6.2 Main Interface of Net-viewer
TABLE OF CONTENTS
FCC RADIATION NORM:................................................................................................................................................. 2
PACKAGE CONTENTS: .................................................................................................................................................. 3
SYSTEM REQUIREMENTS: ............................................................................................................................................ 3
SAFETY INSTRUCTION: ................................................................................................................................................. 5
CHAPTER 1: DVR FEATURES........................................................................................................................................ 6
CHAPTER 2: LAYOUT..................................................................................................................................................... 7
2.1 FRONT PANEL (PLEASE REFER TO ACTUAL PRODUCT FOR DETAIL) .............................................................................. 7
2.2 REAR PANEL (PLEASE SEE ACTUAL PRODUCT FOR DETAIL) ........................................................................................ 8
2.3 REMOTE CONTROL .................................................................................................................................................... 9
2.4 MOUSE OPERATION ................................................................................................................................................ 10
CHAPTER 3: DVR/CAMERA INSTALLATION.............................................................................................................. 11
3.1 CONNECTING THE DVR TO A TV OR MONITOR .......................................................................................................... 11
3.2 CONNECTING THE POWER SUPPLY........................................................................................................................... 11
3.3 CONNECTING THE CAMERAS .................................................................................................................................... 11
CHAPTER 4: DVR START UP ....................................................................................................................................... 12
4.1 SYSTEM INITIALIZATION ........................................................................................................................................... 12
4.2 MAIN INTERFACE ..................................................................................................................................................... 12
CHAPTER 5: DVR MENU AND OPTIONS .................................................................................................................... 13
5.1 MAIN MENU PREVIEW .............................................................................................................................................. 14
5.2 MAIN MENU ............................................................................................................................................................ 15
5.2.1 Recording Functions .................................................................................................................................. 15
5.2.1.1 Record Setup......................................................................................................................................................... 15
5.2.1.2 Motion .................................................................................................................................................................... 16
5.2.1.3 Alarm ...................................................................................................................................................................... 16
5.2.2 Playback ....................................................................................................................................................... 17
5.2.3 Network Setup – Intranet (Internal Access).............................................................................................. 19
5.2.4 Network Setup – Global Access (Connected Directly to Modem).......................................................... 20
5.2.5 Network Setup – Global Access (Connected through a Router or Firewall)......................................... 21
5.2.6 Mobile Setup ................................................................................................................................................ 26
5.2.7 Mobile Phone Access ................................................................................................................................. 26
5.2.8 E-Mail Setup ................................................................................................................................................. 36
5.2.9 Camera ......................................................................................................................................................... 36
5.2.9.1 Camera Setup ........................................................................................................................................................ 36
5.2.9.2 PTZ ......................................................................................................................................................................... 37
5.2.10 System........................................................................................................................................................ 37
5.2.10.1 Date/Time ............................................................................................................................................................. 37
User’s Manual
5.2.10.2 Password ............................................................................................................................................................. 38
5.2.10.3 Language ............................................................................................................................................................. 38
5.2.10.4 Hard Drive ............................................................................................................................................................ 38
5.2.10.5 Video .................................................................................................................................................................... 39
5.2.10.6 System Maintenance........................................................................................................................................... 39
5.2.10.7 Info........................................................................................................................................................................ 39
5.3 LOCK ...................................................................................................................................................................... 39
5.4 VIEW OPTIONS ........................................................................................................................................................ 39
5.5 PTZ CONTROL ........................................................................................................................................................ 40
5.5.1 Cruise Setup ................................................................................................................................................ 40
5.6 PIP MODE............................................................................................................................................................. 40
5.7 PLAYBACK .............................................................................................................................................................. 40
5.8 MUTE ..................................................................................................................................................................... 40
5.9 START ROTATE ....................................................................................................................................................... 40
5.10 START CRUISE ...................................................................................................................................................... 40
CHAPTER 6: NET-VIEWER PROGRAM ....................................................................................................................... 41
6.1 LOG-IN TO NET-VIEWER .......................................................................................................................................... 41
6.2 MAIN INTERFACE OF NET-VIEWER ............................................................................................................................ 42
6.2.1 Menu column ............................................................................................................................................... 42
6.2.1.1 Live ......................................................................................................................................................................... 42
6.2.1.2 Playback................................................................................................................................................................. 42
6.2.1.3. Remote Setting..................................................................................................................................................... 43
6.2.1.4. Local Setting......................................................................................................................................................... 43
6.2.1.5 Log out ................................................................................................................................................................... 43
6.2.2 Play Control ................................................................................................................................................. 44
6.2.3 PTZ Control .................................................................................................................................................. 44
6.2.4 Remote Backup ........................................................................................................................................... 44
6.2.5 Multi Player File format............................................................................................................................... 45
1
User’s Manual
FCC RADIATION NORM:
FCC
This equipment has been tested and found to comply with limits for Class B digital device pursuant
to Part 15 of Federal Communications Commission (FCC) rules.
FCC Compliance Statement
These limits are designed to provide reasonable protection against frequency interference in
residential installation. This equipment generates, uses, and can radiate radio frequency energy,
and if not installed or used in accordance with the instructions, may cause harmful interference to
radio communication. However, there is no guarantee that interference will not occur in television
reception, which can be determined by turning the equipment off and on. The user is encouraged to
try and correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna

Increase the separation between the equipment and the receiver

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected to.
CAUTION!
The Federal Communications Commission warns the user that changes or modifications to the unit
not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
2
User’s Manual
PACKAGE CONTENTS:
Your new Security Camera and DVR Kit will ship with the following items.
16BL-85GB
16BL-161TB
SYSTEM REQUIREMENTS:
Please be sure the computer that you install the included software with complies with the following
specifications:
-
IBM PCs or 100% Compatibles
-
Windows® XP, Vista, 7
-
Internet Explorer 7 or Newer Web Browser Software
3
User’s Manual
-
CD-ROM Drive (for software installation)
4
User’s Manual
SAFETY INSTRUCTION:
1. Use proper power source.
Do not use this product with a power source that applies more than specified voltage
(100-240V AC).
2. Never insert any metal into the DVR or any openings.
Putting metal into the DVR case can cause danger of electric shock.
3. Do not operate in wet or dusty area.
Avoid places like a damp basement or dusty hallway.
4. Do not expose this product to rain or use near water.
If this product accidentally gets wet, unplug it and contact technical support immediately.
5. Keep product surfaces clean and dry.
To clean the outside case of the DVR, use a lightly dampened cloth (no solvents). Do not
use any cleaning solutions or cleaner.
6. Provide proper ventilation.
Use in well ventilated area to avoid overheating of the device.
7. Do not attempt to remove the top cover.
If any abnormal operation is observed, unplug it immediately and contact technical support.
8. Do not attempt to remove the top cover.
Warning: You may be subjected to severe electrical shock if you remove the cover of the
DVR.
9. Handle DVR box carefully.
If you accidentally drop your DVR on any hard surface, it may cause a malfunction. If the
DVR doesn’t work properly due to physical damage, contact an authorized dealer for repair
or exchange.
10. Recommended to use with UPS (Uninterruptable Power Supply)
Connecting your DVR and cameras to a UPS allows continue operation even during power
outages. The duration of power out usage time depends on types of UPS used.
11. Make sure there is good air circulation around the unit.
This DVR system uses a hard drive for video storage, which generates heat during
operation. Do not block air holes/vents (bottom, upper, sides and back) of the DVR that
reduce the generated heat while the system is running. Install or place this product in a well
ventilated area.
5
User’s Manual
CHAPTER 1: DVR FEATURES
Other Features:
•
•
•
•
•
•
•
H.264 compression
Real time recording on 16 channels
USB Backup to flash drive
Triplex operation: view, record, playback simultaneously
Security Certified Hard Drive pre-installed
Easy control with USB mouse
Instant viewing using Windows® Mobile™, Symbian® S60 Version 3 & 5, iPhone®,
Blackberry®, and Android®
•
Internet Remote Functions*: View, Search & Playback, Backup and Setup
•
•
Email alerts with JPEG attachment
Microsoft Windows® XP, Vista, and 7 compatible
6
User’s Manual
CHAPTER 2: LAYOUT
2.1 Front Panel (Please refer to actual product for detail)
3
6
13
Item
Buttons /
Indicators
1
HDD indicator
2
IR Receiver
3
Power indicator
4
MENU/ESC
5
5
7
8
9
Marks
HDD
11
10
12
Functions
When the “Red” indicator flashes it means
the hard drive is being used.
Remote control signal receiver
PWR
If the “Green” indicator is on the system is
properly powered
Enter into main menu or exit menu

Move up

Move Left / Rewind
Select Button, press to enter sub menu /
Change to PTZ (Pan Tilt Zoom) control
mode
Navigation
Buttons

Move Right / Play Forward

Move Down
0-9
Press to switch between channels (Press
and hold ‘0’ for 5 seconds to switch output
between VGA and BNC)
6
Numeric Buttons
7
Display Mode
8
Mute
MUTE
Disable Audio
9
PLAY

Press to play
10
PAUSE/FRAME
11
STOP
12
REC
Start Manual recording
13
USB Data Port
Connect USB device (Flash Drive, Hard
Drive)
Press to switch the display between
Sixteen, Nine, Quad, and single channel
Pause / play frame by frame

Stop Playback; stop manual recording
7
1
4
2
User’s Manual
2.2 Rear Panel (Please see actual product for detail)
1
2
3
5
4
6
7
8
11
9
Item
10
12
Physical
ports
Connection method
1
Video inputs
Connect CH1-16 ( BNC interface)
2
Video outputs
Connect to monitor inputs ( BNC interface)
3
Audio input 1
4 Channel (BNC interface for Channel 1~4)
4
Audio Outputs
Audio Signal Outputs to amplifier or audio equipments
( BNC interface)
5
Audio input 2
12 Channel (for Channel 5~16, included interface cable
required)
6
Ethernet Port
Connect intranet, internet (RJ45 interface)
7
Multi I/O
Output Port for Pan Tilt Zoom, Alarm and Sensors
8
Power Switch
Switch the DVR ON or OFF
9
HDMI
Connect to Monitor with HDMI input port
10
VGA
Connect to monitors with VGA input port
11
USB Port
Connect USB mouse
12
Power Port
Connect power supply - DC12V 5A
8
User’s Manual
2.3 Remote Control
The remote control is the secondary input device for navigating the system’s interface.
To use the remote control:
REC
Start Recording Manually
SEARCH
Turns Search Menu
2x2
Change Display into 2x2 (Quad) mode
3x3
Change Display into 3x3 (NINE) mode
4x4
Change Display into 4x4 (SIXTEEN) mode
AUTO
Put display in preset display sequence in
Video/Audio Setup Menu
Channel Select (Press and hold ‘0’ for 5
0-9
seconds to switch output between VGA
and BNC)
DISPLAY
MODE
Navigation
Buttons
Enter
Press to rotate between different display
modes
MENU/ESC
Open menu or go back to previous menu
Press to navigate in option menus
Press to go into sub menu
FWD
Forward
REW
Rewind
PLAY
Play
STOP
Stop
PAUSE/
FRAME
Press to pause or play frame by frame
SLOW
Play in Slow motion
Z+ Z-
Zoom in and out when in PTZ control
F+ F-
Adjust Focus when in PTZ control
I+ I-
Change the Iris point in PTZ control
PTZ
Open PTZ control
LOCK
9
Put DVR in lock mode
User’s Manual
2.4 Mouse Operation
You can use a mouse instead of the front panel buttons or remote control to navigate the
operation of your DVR
The mouse is the primary input device for navigating system menus.
To use a mouse with the system:
1. Connect a USB mouse to the Top USB MOUSE port on back panel of the system.
NOTE: Only the bottom USB port on the back panel is designed for data backup to a
USB flash drive. Do not connect a USB flash drive to the top USB port on the rear panel.
2. Use the mouse buttons to perform the following:
a. Left-Button: Click to select a menu option; during live viewing in split-screen,
double-click on a channel to view the selected channel in full-screen; double-click
the channel again to return to split-screen view
b. Right-Button: Click to open the Sub-Menu, or click to return to previous option
menu.
3. Scroll-Wheel: No function
10
User’s Manual
Chapter 3: DVR/Camera installation
3.1 Connecting the DVR to a TV or Monitor
Using the supplied BNC to RCA connector
1. Connect the BNC to RCA connector to the back of the DVR labeled Video Output (refer to
Chapter 2.2, Rear Panel Picture)
2. Connect the other end of the cable to an open RCA VIDEO input on your TV or Monitor
3. Select the appropriate video input on your TV or Monitor to view the DVR
NOTE: Your DVR must be powered on so you can view on your TV or Monitor.
3.2 Connecting the Power Supply
1. Plug the provided power supply into the back of the DVR labeled “DC12V”
2. Plug the other end of the power Adapter into any 110V outlet within your home or business.
NOTE: Connecting your DVR and Cameras power source into a UPS or battery backup system will
provide you recorded coverage after power failures. Time depends on type of UPS used.
NOTE: Ensure the cable is pushed all the way into the power supply. Otherwise the DVR will not
power on!!
3.3 Connecting the Cameras
NOTE: Prior to mounting the cameras to their desired destination, please ensure all 8 cameras are
working. Perform these steps near the DVR. Once all 8 cameras are up and running, then you can
lay the cables and mount the cameras to their desired location.
1. Each camera comes with 60ft. of cable per camera. Using one cable per camera, plug each
BNC connector of the camera into the 60ft cable.
2. Plug the other end of the cables into the back of the DVR labeled “CH1 thru CH16”
3. Connect the provided 4-way power splitters to the DC jacks of the cameras, and plug the
power splitter to one of the camera adapters.
4. Plug the camera adapters into any 110V outlet or UPS.
11
User’s Manual
CHAPTER 4: DVR START UP
4.1 System Initialization
After connecting the power adapter and turning on the power, the system will boot-up and start
initializing.
4.2 Main Interface
After initialization, the main interface will load. When there are
video inputs, the interface will display live images from the
cameras. In the main interface, if you use the mouse to
double-click the live image of any channel, the image will be
maximized to full screen, by double-clicking again, the display
will return to multiple channel mode displaying image from
multiple cameras; clicking the right button of the mouse, will
load the Pop-up Menu; by clicking the left button of the mouse
to select options; when clicking any area outside the menu,
you will close the Pop-up menu.
USING THE ONSCREEN DISPLAY
Use the system’s graphical onscreen display to navigate menus and configure options and
settings.
1. Date & Time: Displays the date and time on the system;
2. Channel Title: Displays the customizable name for the channel.
3. Record Status: Displays the current recording status of the system: R = normal recording; M =
motion recording; H = HDD error or HDD full and I = Alarm Recording.
4. Channel number: Displays channel number.
NOTE: By default, passwords are disabled on the system. You do not need to enter a
password when accessing any system menus. However, for security purposes, it is highly
recommended to enable passwords on the system using the Password Menu.
For details, see “Managing Passwords”
12
User’s Manual
CHAPTER 5: DVR MENU AND OPTIONS
Mouse Only
When using the mouse, use the Sub-Menu to access several system options, including the
Main Menu.
To open the Sub-Menu:
Right-click anywhere onscreen to open Sub-Menu.
Select one of the following options:
1. MAIN MENU: Opens the main system menu
2. Lock: Password protect access to menu and options
3. View Options: Change between different viewing options
4. PTZ: Opens the PTZ control menu
5. PIP: Choose between showing one or two small pictures
within the main display picture.
6. Playback: Open the Search Menu to view recorded video
7. Mute On: Select to mute audio
8. START ROTATE: Start sequential display
9. START CRUISE: PTZ cruise settings
To close the Sub-Menu, click anywhere onscreen.
Using the Virtual Keyboard – Mouse Only
When using the mouse, you can input certain values using the onscreen virtual keyboard.
You will need to use the Virtual Keyboard when entering your User ID and Password.
To use the Virtual Keyboard:
1. Click on an option or field, such as the User ID and Password
fields.
2. Click 0~9 to enter the desired digit.
to switch between numerals, upper and
3. Click
lowercase letters, and other characters (only for certain
options)
to Backspace/Delete.
4. Click
NOTE: The buttons will turn from orange to white when you
select the button with the mouse cursor.
5. Click
13
to enter/confirm and close the Virtual Keyboard.
User’s Manual
5.1 Main Menu Preview
Record
Record
Functions
Motion
Alarm Setup
Playback
Internet / LAN
Mobile
Network
E-mail Setup
MAIN MENU
Camera Settings
Camera
PTZ
Date/Time
Password
System
Language
Advanced
Hard Drive
Video
Maintain
Info
14
User’s Manual
5.2 Main Menu
Right-click the mouse, a pop-up menu will be displayed on
the screen. Click “MAIN MENU” button on the pop-up menu
to enter into Main Menu. You can also use the Menu button
on the front panel to open the Main Menu. When using the
front panel buttons, use the FWD and REW button to move
in the menu, and use the SEL button to select the icon. Use
the ESC button to return to previous window. In Main Menu,
you can change settings such as Record Settings, Playback,
Network, Camera, or System settings such as Hard Disk
Drive, Video Output, System Maintenance etc.
5.2.1 Recording Functions
5.2.1.1 Record Setup
Select Main Menu  Record Settings  Record
Functions to open the RECORD SETUP menu. The
adjustable options are as follow:
Record: Allows you to turn each channel ON/OFF.
Audio: Allows you to Enable/Disable the audio port if you
have audio enabled camera installed.
Quality: Choose between “Good”, “Better”, and “Best”
resolution.
Copy: Use this option to duplicate the setting of one
channel to another
File Size: Set the file size limit of each recorded clip.
Framerate: Choose the frame rate of your recording.
Resolution: Choose between “D1” (Highest), “HD1”
(Mid), and “C1F” (Low) resolutions.
REC. MODE: Choose between Time Schedule Record or
Continuous. Time Schedule will allow you to set motion
detection or record at a specific time of day/night.
Note: Select Time Schedule Record and the select Schedule to access the below menu.
SCHEDULE recording options include ALL, CH-1, CH-2,
CH-3, CH-4…CH-16 respectively. Please select the option
you need to record according to the schedule, the channel
you have set will be highlighted in “Blue” and channels you
have not set will be “Grey”.
To setup weekly schedules, click on the box of the corresponding time. Choose between
Motion, Continuous, or No Recording and then click on each box in the schedule time line
that you want to apply the select record type to. You can also use the “From – To” pull-down
menus and Copy button to copy settings from one day to another. After you have
completed the schedule, click “Apply” button to save the settings.
You can also click on the Default button to use the system defaults. The system default settings
are:
Alarm all time on = Motion Detection = ON
15
User’s Manual
5.2.1.2 Motion
To configure the Motion Detection function of the
DVR, click “MAIN”  “Recording Functions” 
“Motion” to enter the Motion Detect Setup window.
Channel: Choose the channel you would like to
configure to have specific motion detection function.
Motion Detection: Enable or Disable Motion Detection
of the selected channel.
Sensitivity: Choose the level of sensitivity of motion
detection. 1 is the least sensitive.
Detection Area: Click this button of the corresponding
channel to select the area you want to have motion
detection. The channel is separated into a 15*10 area.
When any movements in the selected area are detected,
recording or alarm will be triggered. The
semi-transparent area means no motion detection will be
performed in those areas.
Copy: Duplicate the setting of the selected channel to
other channels.
Red = Motion Detection Enabled
Clear = Motion Detection Disabled
NOTE: You can click and drag the mouse cursor when selecting/deselecting the motion area.
5.2.1.3 Alarm
To configure the Alarm mode of each channel, click
“Main Menu”  “Record Settings”  “Alarm” to enter
into “ALARM SETUP” menu.
Channel: Select the channel you would like to configure
Alarm settings
I/O Status: Select between “NO” (Normal Open), “NC”
(Normal Close), and OFF depending on your external
Alarm.
Copy To: Use the function to duplicate the same setting
of one channel to another.
16
User’s Manual
Click the “Alarm Config” button to configure the
alarm settings in detail.
MD Alarm: Set action when motion is triggered.
I/O Alarm: Set action when external alarm is triggered.
HDD Loss: Set action when HDD is operating
irregularly.
HDD Space: Set this to trigger the alarm(s) when the
“HDD Overwrite” option is disabled and the HDD is full.
Video Loss: Set this to trigger the alarm when any of
the camera signal is distorted or loss.
ALARM Time: Configure these options for how long the
external and built in buzzer will react when alarm is
triggered.
Pre Record: Your DVR temporarily store the 5 seconds
of video before any alarm is triggered. Set this to “ON”
if you would like the pre-recorded 5 seconds to be
saved to your HDD also.
5.2.2 Playback
To play a recorded video, select “Main Menu” 
“Playback” Functions to open the RECORD SEARCH
menu.
To search for a file, enter specific date and click
“SEARCH”, you will find all the recordings of that day.
You can play video Forward at 2x, 4x, and 8x speeds,
Slow play at 1/2x, 1/4x, 1/8x, or normal play, pause and
play frame by frame using the playback control bar, and
adjust volume by clicking or sliding tune control bar.
When playback is finished, system will return to previous
menu.
To search by file, click the “FILE LIST” button. This option will allow you to view all of the
available files by channel and type (all, normal, or alarm).
You can select a file and push the SEL button to playback the file, or use the FWD button and
down button to select options or backup the recorded file you selected. You can also put a
check mark in the box at the end of multiple files if you want to backup more then one file at
a time.
First:Indicates the first page of recording history you have
searched. When you view other pages, clicking [First] button
brings you back to Page one.
Last (Previous page): When viewing event list, clicking
“Previous page” button will take you back to page before the
one you are currently viewing (except the first page).
NEXT (Next page): When viewing event list, clicking “Next
page” button will take you to the page after the one you are
currently viewing (except the last page).
Back (Last page): Indicates the last page of recording history you have searched. When you
view other pages, clicking the “Last page” button will take you to the Last page of the
searched files.
All (Select All): Allows you to select all of the events on the current page.
Inverse (Select Invert): Allows you to revert the selected and unselected events on the
current page except those you have currently selected.
Backup: If you want to backup one recording from the file list, use the Detail Files List to find
recorded video on your system and copy it to a USB flash drive (not included).
17
User’s Manual
NOTE: The system is compatible with most major brands of USB flash drives, with capacities
from 256 MB to 4 GB.
To backup recorded data:
1. Connect an empty USB flash drive to the bottom USB port on the back panel of the
system.
2. Open the Search menu and search for recorded data on the system.
3. Click FILE LIST.
4. Select the files you want to backup and click the "BAK" box next to the file name, select
multiple files if desired. Click ALL to select all files; click OTHER to deselect all files.
NOTE: The size of each file is shown in the File List menu. Use this to help you find a USB
flash drive large enough to hold all the files you wish to backup.
5. Click BACKUP from the side-panel to immediately begin copying the files to the USB flash
drive.
NOTE: Backup progress appears in the status window. DO NOT remove the USB flash drive
during backup.
6. The system will create a folder on the USB flash drive named RecordFile. The files are saved as
.264 files. If backup is successful, click CLOSE in the confirmation window and then
remove the USB flash drive.
NOTE: If there is not enough space on the USB flash drive, the system will display the
following: "Space is not enough."
NOTE: Backup file will be in H.264 format, you can convert it to AVI format using the
Multimedia Player program that comes with the DVR or through the net-viewer program, so
you can use any player that supports AVI format
18
User’s Manual
5.2.3 Network Setup – Intranet (Internal Access)
To access the NETWORK SETUP menu, select Main Menu  NETWORK to open the
NETWORK SETUP menu.
If your DVR is connected to a router of your local network (intranet), then you can setup the
NETWORK Setup section of the DVR to view the image your DVR is recording remotely
using computers connected within your network.
Important Note: You will not be able to access your DVR if your DVR is connected behind two
or more routers.
Note: Prior to changing the NETWORK Setup of your DVR, it is strongly recommended that
you perform the following tasks:
1. Access the configuration page of your router.
2. Reserve an IP Address in your router that is not used by other computers or devices
connected to your internal network.
3. Write down the assigned IP Address of your DVR, Subnet Mask, IP Address of your Router
(Gateway) of your DVR for future reference when configuring the DVR.
1. Select STATIC as the network TYPE.
2. Setup Media Port and Web Port (recommended to
leave these at the default values).
3. Enter the IP Address that you have reserved at the
beginning of this section into this field to be the unique
address of your DVR in your local network.
4. NETMASK: It is recommended to leave the Subnet
mask as the default 255.255.255.0.
5. Set the GATEWAY to the IP Address of your router.
6. Enter the DNS (Domain Name Server) Address, Set
this to you router's IP address.
7. Leave the UPNP option at “Enable”. Click “APPLY”
to save your change.
19
User’s Manual
5.2.4 Network Setup – Global Access (Connected Directly to Modem)
To access the NETWORK SETUP menu, select Main Menu  NETWORK to open the
NETWORK SETUP menu.
If you would like to access your DVR while you are outside of your home, please follow the
instructions below to configure the NETWORK Setup page of your DVR
Important Note: If you are using a DSL modem, the modem must be set to “bridge mode”.
Important Note: We will not be able to help you set up the network configurations if you have a
RADIUS Server or Network Magic installed.
Note: Prior to changing the NETWORK Setup of your DVR, it is strongly recommended that
you perform the following tasks:
1. Find out from your Internet Service Provider (ISP) what kind of service you are using.
Note: Your DVR supports these three common types of Internet Services: DHCP (Cable
Modem), PPPoE (DSL Modem) and Static IP (Fiber Optics). Actual service type may vary,
please ask your ISP for the exact service type.
2. Write down the: IP Address provided by your ISP (if your ISP is using Static IP), Subnet
Mask, Gateway Address, DNS Address(es) provided by your ISP of your DVR for future
reference when configuring the DVR.
DHCP
1. If your ISP uses DHCP networking, select DHCP
network TYPE.
2. Leave Media Port at 9000
3. Setup Web Port (leave at 80 but some ISPs block
inbound traffic on port 80 to prevent web servers so
if the DVR cannot be remotely accessed choose a
different port number)
4. Leave the UPNP option at “ON”. Click the “DDNS
SETUP” Button.
5. You will need to apply for a Dynamic DNS account
and register a Domain Name with one of the known
DDNS provider. Enter your DDNS Provider’s
HOST NAME, USERNAME, and PASSWORD in
the DDNS SETUP page.
NOTE: If you would like a free DNS account please visit
www.nightowldvr.com
20
User’s Manual
STATIC IP
1. Select STATIC as the network TYPE.
2. Leave Media Port at 9000
3. Setup WEB Port (leave at 80 but some ISPs block
inbound traffic on port 80 to prevent web servers so
if the DVR cannot be remotely accessed choose a
different port number)
4. Enter the IP Address that you have reserved at the
beginning of this section into this field to be the
unique address of your DVR in your local network.
5. NETMASK: It is recommended to leave the Subnet
mask as the default 255.255.255.0.
6. Set the GATEWAY to the IP Address of your router.
7. Set the DNS (Domain Name Server) Address to the
IP Address of your router
8. Leave the UPNP option at “Enable”. Click “APPLY”
to save your changes.
PPPoE
1. If your ISP provides you a Static IP Address, select
STATIC as the network TYPE.
2. Leave Media Port at 9000
3. Setup Web Port (leave at 80 but some ISPs block
inbound traffic on port 80 to prevent web servers so
if the DVR cannot be remotely accessed choose a
different port number)
4. Enter your PPPoE NAME and PASSWORD so your
DVR will be able to obtain service from your ISP.
5. Leave the UPNP option at “Enable”. Enter the
DNS (Domain Name Server) address.
6. You will need to apply for a Dynamic DNS account
and register a Domain Name with one of the known
DDNS provider. Enter your DDNS Provider’s
HOST NAME, USERNAME, and PASSWORD in
the DDNS SETUP page.
5.2.5 Network Setup – Global Access (Connected through a Router or Firewall)
To access the NETWORK SETUP menu, select Main Menu  NETWORK to open the
NETWORK SETUP menu.
If you would like to access your DVR while you are outside of your home or office network,
please follow the instructions below to configure the NETWORK Setup of your DVR
Important Note: You will not be able to access your DVR if your DVR is connected behind two
or more routers.
Important Note: If you are using a DSL modem, the modem must be set to “bridge mode”.
Important Note: We will not be able to help you set up the network configurations if you have a
RADIUS Server or Network Magic installed.
Note: Prior to changing the NETWORK Setup of your DVR, it is strongly recommended that
you perform the following tasks:
21
User’s Manual
1. Access the configuration page of your router or Firewall.
2. Reserve an IP Address in your router or firewall that is not used by other computers or
devices connected to your internal network.
3. Make sure your router is configured properly for computer or devices outside of your local
network to access your DVR through your router. To do so, please use the following
method(s): NAT (Network Address Translation), Port Forwarding, DMZ (De-Military Zone),
DDNS (Dynamic DNS). Please refer to your router or firewall user’s manual for reference.
Note: Improper configuration on the router or firewall will prevent you from accessing your
DVR from outside your network.
4. Write down the assigned IP Address of your DVR, Subnet Mask, IP Address of your Router
(Gateway) of your DVR for future reference when configuring the DVR.
1. Select STATIC as the network TYPE.
2. Leave Media Port at 9000
3. Setup Web Port (leave at 80 but some ISPs block
inbound traffic on port 80 to prevent web servers so if
the DVR cannot be remotely accessed choose a
different port number)
4. Enter the IP Address that you have reserved at the
beginning of this section into this field to be the unique
address of your DVR in your local network.
5. NETMASK: It is recommended to leave the Subnet
mask as the default 255.255.255.0.
6. Set the GATEWAY to the IP Address of your router.
7. Set the DNS (Domain Name Server) Address to the
IP Address of your router
8. Leave the UPNP option at “Enable”. Click “APPLY”
to save your changes.
Port Forwarding
To access the DVR from a remote computer over the internet via internet browser (Internet
Explorer).
1. Forward Port 80 and Port 9000 in the router attached to the DVR, to the IP address of
the DVR. *If you can’t use HTTP Port 80 due to use or your Internet Service Provider is
blocking it, use a different port like 1024 as the WEB PORT. When selecting a different
port, forward the new port to the IP address of the DVR and change the settings in the
DVR Network settings. You will also need to add the new port to the end of the IP
address in the browser window. For example, if you use port 1024, you add “:1024” to
the end of the IP address.
2. For instructions on the most popular routers go to www.portforward.com. Click on the
“Routers List” and select your router from the list of router manufacturers by clicking on
the brand and model number.
22
User’s Manual
3. On the next page that opens, click on the “Default Guide” link.
port forwarding instructions for your router.
This will take you to the
4. When you access the DVR from a remote computer, you also need to use a different
address in the Internet Explorer browser window. Instead of entering the IP address of
the DVR, you need to enter the public IP address of the router that the DVR Is attached
to. You can get this address by going to www.myipaddress.com from the
computer that is attached to the same router as the DVR. This website will display the
box in that shows the IP address you need to use.
Viewing your Night Owl DVR over the Internet (UPnP)
Now that you have set up the DVR on your local network, you will want to access your
camera from a remote location over the Internet. This DVR supports a technology called
Universal Plug and Play (UPnP). With UPNP your DVR will automatically open the
necessary ports in your router to allow remote access to your DVR. To make use of
this feature your router will also need to support UPnP. Most modern routers support
this; however, check your router manufacturer’s website just to make sure.
A. Make sure that your DVR is plugged directly into your router with an Ethernet cord.
B. Log into your DVR’s network setup: Main Menu  Network
C. Verify that the TCP/IP Type is set to DHCP.
D. Ensure UPNP is enabled and leave the default ports as:
Media Port: 9000
Web Port: 1024
Server Port: 18000 (Located in the Mobile section)
E. Your router will usually have UPNP enabled by default, but just to make sure, log into
your router to check it is (refer to manufacturer guidelines on how to do this)
F. Once both your DVR and router have UPNP enabled, you are now able to view your
DVR from any computer with high speed Internet access. To do this you need to type
your external IP address in the Internet Browser address bar followed by :1024
Note: There are 2 types of external IP addresses:
1. Static – Your external IP address will never change, even if you turn your broadband
modem off and on.
2. Dynamic – Your external IP address may be likely to change several times a week.
If you want to access your camera from outside your network and have a Dynamic IP
address, you will have to re-check your external IP address every time you connect to
the internet. You can ask your ISP if they can provide you with a static IP address or you
can eliminate the need to enter an IP address by using our DDNS server at
www.nightowldvr.com. DDNS allows you to enter a normal style internet address into
your browser and it will find your camera, even if you have a dynamic IP address. For
23
User’s Manual
more information on how to set up DDNS, refer to the How to setup DDNS in the
supplied user manual.
Note: If you are still confused call our technical support team at 1-866-390-1303 for
assistance.
Accessing the DVR through Internet Explorer Browser (IE):
Once the network settings on the DVR match the settings of your router, and you have
forwarded the ports needed by the DVR (for remote access over the internet), you need
to modify your browser controls.
Note: Ensure you are using Internet Explorer 7 or newer to use this feature (Open IE, Click
Help, Select “About Internet Explorer”)
To Modify Internet Explorer controls
1. Turn OFF “Pop Up Blocker”
Go to Tools,
Select Pop-up Blocker,
If On please select “Turn Off
Pop-up Blocker”
2. Access Active X Controls
Select Tools
Select Internet Options
24
User’s Manual
Access Custom Security Level
Select the “Security” tab
Select “Custom Level…”
3. Enabling all Active X Controls
On this page scroll down to the ActiveX
Controls and Plug Ins, and set all to either
PROMPT or ENABLED.
To connect to the DVR from a remote computer, you would then open an Internet Explorer
browser window and enter the Internet IP of your router that you received by going to
www.myipaddress.com.
If you get an error message “Program cannot load because the Publisher is unknown” or the
program is unsigned, then go to Internet Explorer > Tools > Internet Options, then click on
the ADVANCED tab on the top right. This will open the window in, scroll down to “Security”,
and select on the options to “Allow software to run or install even if the signature is invalid”,
and “Allow Active Content to Run Files on My Computer”.
Warning! It is strongly recommended to return all Internet Explorer Security to its default
settings after the Active X Control has been installed. Enabling all Active X controls put
your computer at risk of being attacked by malware and spywares.
25
User’s Manual
5.2.6 Mobile Setup
If you would like to allow your DVR to be accessible by a
Mobile device, Click “MAIN MENU”  “Network” 
“Mobile” to open the “MOBILE” menu.
USER NAME: is the user name to enter when logging into
the DVR.
USER PASSWORD: is the password to enter when logging
into the DVR.
Server port: Mobile monitoring port. Setting range is
between 1024 and 65535. Please note that the server port
number must not equal to network menu’s “PORT” setting.
5.2.7 Mobile Phone Access
The DVR is currently compatible with mobile phones running Windows® Mobile, Symbian® S60
Version 3 operating systems and iPhones® on 3G networks.
Before you can access the DVR from a mobile phone, you need to setup the Network
Configuration on the DVR. Go to section 5.2.4 or 5.2.5 for instructions. You will also need to
set the configurations in section 5.2.6.
NOTE: The video speed depends on the speed of the internet connection.
When accessing from a mobile phone with Windows Mobile operating system, follow
these procedures:
1. Install the webcam program that is included on the supplied CD by copying the
“Aseesetup.CAB” file to the mobile phone. You can do this by attaching the mobile phone
to a computer and copying the file from the CD to the phone.
2. Click the windows mobile folder and choose the file “Aseesetup”. Select the file which will
open the window. The file is generally default to save to the Device’s built-in memory, but
you can choose to save it to Storage Card.
3. Choose storage location and click “Install” to start the installation.
4. After installation finishes, click the icon named “Asee” to run the program. This will display
the program screen.
26
User’s Manual
5. Click the “Setting” button to enter the Setting menu.
6.
User name: same as the user name setup in DVR under section
5.2.6.
Password: same as the password setup in DVR under section 5.2.6.
Server address: Enter the Public IP or DDNS address of your DVR.
Port: Same as the Server Port you set in the DVR under section
5.2.6.
Notes: Enter the user defined DVR name (if configured).
Click ”OK” to save the settings and to access your DVR remotely.
When accessing from a mobile phone with Symbian® S60 Version 3 or 5 operating
system, follow these procedures:
1. Install the webcam program that is included on the supplied CD by copying the
“ASee_AL_3rd _0901.sisx” file to the mobile phone if you are using Version 3. Copy the
file “ASee_AL_5th_0901.sisx” if you are using Version 5. You can do this by attaching the
mobile phone to a computer and copying the file from the CD to the phone.
2. Select the copied “.sisx” file on your phone to install it.
3. After the phone finishes copying the file, it will ask for permission to install the program.
Select “Continue” to start the installation.
4. Click the “Continue” button on the information box displaying the program and current
version.
5. Select the location of where you want to install the program, to phone memory or to the
memory card, and then click “Select”.
27
User’s Manual
6. Click “Continue” and wait for the program to install.
7. Once the installation is complete, go to the Applications folder and select the “Asee”
program, and click “Open” to display the software interface. Click the “Setup” button to
open the “Setting” screen.
IP:Enter the Public IP or DDNS address of your DVR.
Port:Same as the Server Port you set in the DVR under section 5.2.6.
User Name: same as the user name setup in DVR under section 5.2.6.
Password:same as the password setup in DVR under section 5.2.6.
Channel: Select the channel you want to monitor and click “DONE” to display the screen to
start viewing the live image.
Alias: Enter the user defined DVR name (if configured)
Option: click to select whether history list should be included.
When accessing with an iPhone® follow these procedures:
1. From you iPhone® Select “App Store” from your home screen.
2. Select the Search icon.
3. Type: “Asee” in the search field.
4. Download and install the “Asee” Application.
5. After the application is installed, click the Asee icon
to run the software.
6. Select the Settings icon at the bottom and input your Username, Server IP Address, Mobile
Port number, Login ID and Password (See Section 5.2.6, Mobile)
28
User’s Manual
7. You will now be watching a live streaming video of your security camera on your iPhone®.
Enjoy!
When accessing from a mobile phone with Blackberry® phones, follow these
procedures:
Note: To prevent flickering screen when connecting to your DVR, please make sure the
firmware on your mobile phone is the latest version. Please visit your mobile phone
manufacturer’s website for further details.
1.
2.
3.
4.
Download and install the “Blackberry Desktop Manager” on your PC.
Connect your phone to your PC via USB cable.
Open the Desktop Manager.
Choose “Application Loader” from the Main Menu.
5.
Under the “Add/Remove Applications” pane, click “Start” Button.
6.
Click the “Browse…” button and locate the “ASee.alx” file on the included CD. Select the
“ASee” file under “Device application selection” and click “Next”.
29
User’s Manual
7.
Follow the installation process and click “Finish” at the end to finish the installation.
Using the Software:
Prior to running the software, please make sure you have edited the Application permission of
the “ASee” application by going to “Settings” -> “Options” -> “Applications”, then
highlight the “ASee” application and select “Edit Permissions” in the drop down menu.
Make sure Connections, Interactions, and User Data are set to “Allow”.
1.
To run the application, the Blackberry viewer is installed in the “Downloads” directory.
2.
Open the “Downloads” folder, and then click the “ASee” icon to open the viewing interface.
1 ---Connect/Disconnect
2 ---Full screen
3 ---Snapshot
4 ---Setup
5 ---Help
6 ---Next Channels/Group
7 ---Navigation Controls
30
User’s Manual
3.
Select the “Setup” options and enter the information of the DVR you want to connect in
Settings.
Name: Enter the Name of this group of settings.
Address:Enter the Public IP or DDNS address of your DVR.
Port:Same as the Server Port you set in the DVR under section 5.2.6.
User ID: same as the user name setup in DVR under section 5.2.6.
Password:same as the password setup in DVR under section 5.2.6.
4.
Select the Network Type supported by your phone.
5.
6.
Click the “Save” button to save the settings, and system will return to Live display.
You can save the connection settings for different DVRs when you give the Settings
different names under Settings and click save. To open the list of DVRs that you have
connected to, click the “History” button to open the History List.
31
User’s Manual
7.
Highlight one record and click the trackball/trackpad to open the History pop up menu.
When “Open” is selected, system will directly be connected to the DVR.
8.
When selecting “Edit” option, system will allow you to edit the record.
9. When selecting “Delete” option, the history record will be deleted.
10. When viewing in live view mode, click “Next Channels/Group” icon to switch channels,
and then choose the channel you want to display.
11. Click the “Full screen” icon to view in full screen display mode, click the “Trackball” on the
mobile phone to quit full screen mode.
12. Click “Next page” again button to view the “Navigation Controls” if you have a PTZ
Camera installed with your DVR.
13. Click “Help” button to view the software’s Help instruction.
32
User’s Manual
14. Click “Close button to exit the program.
When accessing from a mobile phone with Android® phones, follow these procedures:
1. Download the Android software from our website (www.nightowlsp.com/support.htm),
decompress and store the downloaded software in an easy to remember location.
2. Copy the downloaded “Asee.pak” to your phone.
3. Make sure your mobile is connected to a network and can download software/files.
4. Goto “All Program” and select the “Market” icon.
5.
In the “Market” interface, click “Search” on the upper right corner and enter “apkinstaller”
to search for the “Apkinstaller” program.
6.
Highlight and install the “apkInstaller” program searched.
33
User’s Manual
7.
Follow up the installation steps to install the software.
8.
Goto “All Programs” and select “ApkInstaller”.
9.
Locate the “ASee.apk” on the included CD and copy to your phone.
10. Select and install the software to your phone.
34
User’s Manual
11. Goto “All Programs” and select the “ASee” icon.
12. The “ASee” main interface will be displayed.
1
Channel Select
2
Pan/Tilt Control
3
Zoom+/-
4
Focus+ -
5
Iris +/-
6
Play/Pause, Snapshot, Settings, Next Channel
Group and help.
13. Click the Settings icon to open the “Settings” menu.
Enter the device information for the DVR that you would like to
connect to:
Address: Enter the IP address of the DVR
Port: Enter the Mobile Port Number of the DVR under section 5.2.6
Device Name: Enter DVR name (User defined)
User ID: Enter the Login User Name for you DVR under section
5.2.6
Password: Enter the Login User Password for your DVR under
section 5.2.6.
History: Click the “History” button at the upper right hand corner to
view records of previously connected devices.
NOTE: If you are having trouble accessing your DVR from your cell phone please visit
www.NightOwlSP.com to ensure you are using the most up to date software. If your phone
is not compatible with the above list please check our website once again to see if your
phone is listed.
35
User’s Manual
5.2.8 E-Mail Setup
There is also an option for the DVR to send an e-mail to a specific mails box when the alarm
is triggered. To enable this option, follow these steps:
Click the “EMAIL SETUP” button under Network.
Set the e-mail account information of your mail
server. Please contact your Network
Administrator for details and configuration
settings.
5.2.9 Camera
5.2.9.1 Camera Setup
There is also an option for the DVR to send an e-mail to a specific mails box when the alarm
is triggered. To enable this option, follow these steps:
Select Main Menu  Camera  Camera Settings to
open the CAMERA SETUP menu.
CH Name: set up the name display of each channel.
Position: display position of each channel.
Color: Click to open sub-menu to adjust image
brightness, saturation, contrast and hue settings of
each channel.
Display CH Image: enable to display the channel.
Display Time: enable to show the time.
Display Record Time: enable to show the time of
the record.
Copy: Use the function to duplicate of one channel
to another.
COLOR SETUP Menu allows you to adjust
image brightness, saturation, contrast and hue
of each channel.
Click “APPLY” to and then click “OK” to save the
adjusted settings. Click “EXIT” to cancel the
modification, or click “DEFAULT” to restore all
settings to the factory default settings.
Privacy Zone: allows you to mask certain
area(s) of the screen to give you better privacy
protection. Simply enable the check box and
then drag the box to the area that you would like
to mask.
36
User’s Manual
5.2.9.2 PTZ
To configure the PTZ (Pan Tilt Zoom) function,
click “Main Menu”  “Camera”  “PTZ”. The
cameras that come with the kit do not support PTZ
function, please refer to the user’s manual of your
PTZ cameras for proper settings. Please note the
channel settings must match the settings of the PTZ
camera.
5.2.10 System
5.2.10.1 Date/Time
Click “MAIN”  “SYSTEM”  “DATE/TIME” to enter the TIME SETTING window to modify
system date, time, date/time format and time zone, DST (day saving time).
•
•
•
•
•
•
•
•
DATE: Enter the day, month, and year
DATE FORMAT: Select YYYY/MM/DD, or
MM/DD/YYYY
TIME: Enter the time
TIME FORMAT: Use the drop-down menu and
select 12HOURS or 24HOURS
TIME ZONE: Use the drop-down menu to select
the time zone you are in.
NTP: Enable or Disable the Internet Time Server
Function.
NTP SERVER: enter the address of the
international time server for periodic time update.
DST: Use the drop-down menu to select ON/OFF
to enable/disable Daylight Savings Time.
When you click the DST Setting button in the
Date/Time menu, the DST STEEING menu will
open.
• Daylight Saving Time: Enable/Disable Daylight
Saving function.
• Time Offset: Enter the number of hours when
day light saving is active.
• Daylight Saving Time Mode: Select between
Week or Date depending on what day daylight
saving takes place.
• Start Time: The starting date of Daylight Saving.
• End Time: Set the date Daylight Saving ends.
37
User’s Manual
5.2.10.2 Password
Click “Main Menu”  “System”  “Password”.
This option allows you to set the user permissions
and password of up to 7 users.
.
The password supports up to 6 characters. Click
“APPLY” to save the settings.
NOTE: Please write down your passwords and
store in a safe location.
5.2.10.3 Language
Click “Main Menu”  “System”  “Language” to
setup the default system language.
5.2.10.4 Hard Drive
To manage the installed Hard Disk, click “Main
Menu”  “System”  “Advanced”  “Hard Drive” to
enter “HDD MANAGEMENT”. The HDD Management
screen shows the capacity and available recording time
of the installed hard drive and let you configure whether
to overwrite old recordings or stop when HDD is full.
Select “Format HDD” to format the installed Hard Disk
Drive and erase all recorded files.
Select “Format USB” to format the installed USB Drive
by erasing all recorded files on the drive.
To enable your DVR to overwrite old recording files,
choose “ENABLE” at the OVERWRITE field and then
click Apply.
38
User’s Manual
5.2.10.5 Video
Click “Main Menu”  “System”  “Advanced” 
“Video” to setup Video and Audio output options
such as resolution and format. You can also
preset a channel display sequence or rearrange the
position and number of each input channel.
5.2.10.6 System Maintenance
Click “Main Menu”  “System”  “Advanced” 
“Maintain” to access the SYSTEM MAINTENANCE
page of your DVR. This option allows you reset the
DVR to factory default settings, update system
software (firmware), and set system auto reboot
time.
When enabling the auto-reboot function, you can
setup system to restart regularly to clear up some
temporary storage memory.
5.2.10.7 Info.
Click “Main Menu”  “System”  “Advanced” 
“Info” to access the system information of your DVR.
5.3 Lock
Click “Lock” of the pop-up menu to activate password protection of your DVR. All menu will be
locked until the correct username and password is entered.
5.4 View Options
Click “View Options” of the pop-up menu to select different viewing options such as the number
of cameras to display at the same time or sequential display.
39
User’s Manual
5.5 PTZ Control
5.5.1 Cruise Setup
Open PTZ setting menu if you want to setup cruise function (system default: on), and set up
cruise channel, cruise points etc.
1
1. Channel Select: Select the channel of the installed PTZ
camera.
2. PTZ direction control: Control PTZ moving direction.
3. Zoom, Focus and Iris Control: control direction, zoom,
focus and iris of PTZ.
4. Presetting PTZ positionsUse this to pre-set several spots of the PTZ camera for quick
access.
2
3
: Go to the selected preset spot.
: Set PTZ preset positions
: Delete Current cruise point.
: Save setting.
: Exit.
To start Cruise, exit this screen and click “Start Cruise” of the
pop-up menu.
4
5.6 PIP MODE
Click “PIP MODE” of the pop-up menu to select between one or two small pictures within the
main display.
5.7 Playback
Click “Playback” of the pop-up menu to open the Video Search screen to display a record.
5.8 Mute
Click “Mute On” of the pop-up menu to enable and display sound.
5.9 Start Rotate
Click “START Rotate” of the pop-up menu to start displaying videos from each camera in
preset sequence.
5.10 Start Cruise
If you have purchased a PTZ camera separate and would like to start the PTZ camera to start
cruising, click “START Cruise” on the pop-up menu to start the function set in section 5.5.1
40
User’s Manual
CHAPTER 6: NET-VIEWER PROGRAM
Open Internet Explorer and enter the IP Address or DDNS address of your DVR. A pop-up will ask
you to install an ActiveX (plug-in) to your computer. Please confirm the download and install the
software.
Reminder: If the ActiveX (plug-in) is not downloaded successfully, please check if your
browser’s safety level or firewall setting is set properly (as stated above). Please also make sure all
of the setup of your modem or router is setup properly.
6.1 Log-in to Net-Viewer
After the ActiveX (plug-in) is installed, please
refresh the screen to load the login page. Enter
your DVR’s login information. Click the “Login”
button to view remotely through NetViewer.
Please note default password is empty. System
allows Administrator to set new password as per
section 5.2.10.2.
After successfully Logged in to Net-Viewer,
system will open the live display interface and
connect to audio/video feed automatically.
41
User’s Manual
6.2 Main Interface of Net-viewer
1
2
3
6.2.1 Menu column
Menu column includes “Live”, “Playback”, “Remote Setting”, “Local Setting” and “Logout”.
6.2.1.1 Live
After Logging-in to system, system will enter into Live display. You can enable/disable
showing certain cameras, control the volume, or control the movement of PTZ cameras
if you have such cameras installed.
6.2.1.2 Playback
This option allows you to playback
recordings remotely.
1. Select the day, channel and type and
click search.
2. Select any event from search result list
to playback.
42
User’s Manual
6.2.1.3. Remote Setting
Clicking “Remote Setting” opens this sub menu, option in this menu includes “Record”,
“Network”, “Camera”, and “System”.
Record
Open sub menu “Record” to access the same
“Record” settings that you would see on the firmware
menus of the DVR.
Network
Open sub menu “Network” to access the same
“Network” settings that you would see on the firmware
menus of the DVR.
Camera
Open sub menu “Camera” to access the same
“Camera” settings that you would see on the firmware
menus of the DVR.
System
Open sub menu “System” to access the same
“System” settings that you would see on the firmware
menus of the DVR.
6.2.1.4. Local Setting
Click “Local Setting” to configure where to store files locally on the computer you are
currently accessing your DVR with.
6.2.1.5 Log out
Log out of the system.
43
User’s Manual
6.2.2 Play Control
1. On / Off Live display
: Clicking this button opens and
closes Live display.
: Capture Screen image and save to PC.
2. Capture
3. Recording
: Operate DVR recording remotely
4. Channel display
: These icons stand for
Single Channel display, Quad Channel display, 3x3
Channel display and 4x4 Channel display, and full
screen respectively.
5. Volume control
: Click or slide the control
bar to adjust sound volume.
6.2.3 PTZ Control
1
1. PTZ direction control: Control PTZ moving direction.
2. Zoom, Focus and Iris Control: control direction,
zoom, focus and iris of PTZ.
3. Presetting PTZ positionsUse this to pre-set several spots of the PTZ camera for
quick access.
: Set PTZ preset positions
: Go to the selected preset spot.
:Load previous setting you have saved.
2
: Save setting.
: Start or Stop PTZ Cruise.
: Delete current Cruise point.
3
6.2.4 Remote Backup
You can backup recorded video files from your system to your PC using the Replay menu in
the remote surveillance software.
To backup files remotely:
1. Click Playback at the top of the main screen.
2. Select a date(s) on the calendar and click REFRESH.
3. Double-click a file from the File List to begin playback.
4. Click Download. Backup begins to C:/DVR/[ip_address]/Backup
NOTE: If you playback a file, you must wait for the file to load before backing it up, otherwise
you may receive an error message
5. When file backup is complete, click OK in the confirmation window. The confirmation
window show the save path of the backup file.
NOTE: Backup files are saved as .264 files.
NOTE: Use the PlayBack Software included on the software CD to playback backed up video.
44
User’s Manual
6.2.5 Multi Player File format
1. If you would like to play any recorded file using video players that supports .avi format, first,
copy or backup file to your PC.
2. Use the AVI Generator software included in the driver CD and install AVI Generator to your
computer.
3. Open the AVI Generator installed on your computer, click Open to find/select the backup file,
and then click “Open”.
Note: the file type you have selected should be *.264 format.
4. Click “Save As” to specify the location and file name for your converted file.
5. Click “Save” to start converting the file into AVI format.
45
User’s Manual
WARRANTY
NIGHT OWL, LLC (“Night Owl”) provides the following warranty to the original retail purchaser only (the
“Purchaser”) with respect to this product (the “Product”):
For a period of one (1) year after the date of sale, the Product shall be free from manufacturing defects in
material and workmanship. In the event that the Product is defective, the Purchaser must return the Product at
Purchaser’s cost (no CODs) to the address below, with the original proof of purchase receipt.
In its sole
discretion, Night Owl will either repair or replace the Product at no additional cost to the Purchaser. Any
replacement Product (or parts) will be covered by the same warranty as the original Product through the
expiration date of the original warranty period.
Exclusions:
This warranty does not apply to the following parts or upon the following events:










Bulbs, LEDs and batteries;
The Product was not used or installed in the manner described in the installation instructions;
Negligent use of the Product, or misuse or abuse of the Product;
Electrical short circuits or power surges;
Use of replacement parts not supplied by Night Owl;
Product is either tampered with, modified, or repaired by another service provider;
Product has not been maintained in accordance with the instructions;
Accident, fire, flood or other acts of God;
Failure to use Night Owl approved accessories;
Defects or damages arising by use of the Product in other than normal conditions (including
normal atmospheric, moisture and humidity conditions).
EXCEPT AS OTHERWISE PROHIBITED BY LAW, THIS WARRANTY IS IN LIEU OF OTHER
WARRANTIES, EXPRESS OR IMPLIED, AND NIGHT OWL NEITHER ASSUMES NOR
AUTHORIZES ANY PERSON TO ASSUME FOR IT ANY OTHER OBLIGATION OR LIABILITY IN
CONNECTION WITH THE SALE OR SERVICE OF THE PRODUCT.
IN NO EVENT SHALL NIGHT OWL BE LIABLE FOR ANY SPECIAL OR CONSEQUENTIAL
DAMAGES ARISING FROM THE USE OF THE PRODUCT OR ARISING FROM THE
MALFUNCTIONING OR NON-FUNCTIONING OF THE PRODUCT, OR FOR ANY DELAY IN THE
PERFORMANCE OF THIS WARRANTY DUE TO ANY CAUSE BEYOND ITS CONTROL. THIS
WARRANTY SHALL NOT APPLY TO INSTALLATION OR THE REMOVAL AND
REINSTALLATION OF PRODUCTS AFTER REPAIR.
Night Owl does not make any claims or warranties of any kind whatsoever regarding the Product’s potential,
ability or effectiveness to prevent, minimize, or in any way affect personal or property damage or injury. Night
Owl is not responsible for any personal damage, loss or theft related to the Product or to its use for any harm,
whether physical or mental related thereto. Any and all claims or statements, whether written or verbal, by
46
User’s Manual
salespeople, retailers, dealers or distributors to the contrary are not authorized by Night Owl, and do not affect
this provision of this warranty.
Returns under this Warranty
In order to obtain service, please make sure that you have registered your product on-line no later than thirty
(30) days after purchase at www.NightOwlSP.com in the warranty registration section or in any other matter
described in the instructions.
TOLL FREE CUSTOMER SERVICE
North America: 1-866-390-1303
1-774-256-7250
Email: Support@NightOwlSP.com
Website: www.NightOwlSP.com
Email:
Support@NightOwlSP.com
TOLL FREE: 1-866-390-1303
Rev 03-2010
47
User’s Manual
48
User’s Manual
49
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising