A/V LCD 8-DEVICE WITH LEARNING
A/V LCD 8-DEVICE WITH LEARNING
UNIVERSAL REMOTE CONTROL (URC-8910)
User’s Guide
TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Setting The Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Features And Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Key Charts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Setting Up Your Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Programming TV/VCR Combo Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Manufacturer’s Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setup Codes for TVs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setup Codes for VCRs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Setup Codes for TV/VCR Combos . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Setup Codes for DVD Players . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Setup Codes for Cable Converters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Setup Codes for Satellite Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Setup Codes for CD Players . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Setup Codes for Audio Amplifiers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Setup Codes for Audio Cassette Decks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Setup Codes for Audio Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Setup Codes for Audio Turntables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Setup Codes for Misc. Audio Services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Setup Codes for DAT Recorders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Setup Codes for LD Players. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Setup Codes for Home Automation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Setup Codes for Video Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Searching For Your Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Using Learning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Programming A Learning Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Deleting A Function From A Learning Key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Using Volume Lock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Programming Volume Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Programming Volume Unlock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Using Macros. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Programming A Favorite Channel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Programming A Master Power Key With Instant Channel Selection. . . . . . . . . . . . . . . . . . . 35
Clearing A Macro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Re-Assigning Device Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Using Keymover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Programming Keymover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Restoring Keymover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Using Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Programming Favorite Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Using The Home Theater Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Control Organization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Programming The Home Theater Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Operating The Home Theater Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Using Commercial Skip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Programming Commercial Skip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Operating Commercial Skip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Restoring Factory Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
About Upgrading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Key Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
2
INTRODUCTION
The One For All A/V LCD 8-Device With Learning Universal Remote
Control (URC-8910) is our latest high-performance universal
remote control. It is designed to operate up to eight home entertainment devices, including TV, video, and audio components. Moreover,
this remote control contains sophisticated technology that will allow
you to conveniently consolidate the clutter of all of the original
remote controls used in your home entertainment system. It’s
packed with easy-to-use features such as:
• Advanced Liquid Crystal Display (LCD) with 15 alphanumeric
characters, real-time clock, and icons for constant visual feedback
of operations and programming sequences
• A unique Home Theater mode that combines different device
controls under one mode for operating convenience
• Three macro keys for instant activation of favorite key sequences
• Four learning keys to capture unique functions from your
devices’ original remote controls
• Key Mover for copying keys from one device to another, or to a
different position in the same mode
• Code Search to help you program device codes without using the
code list (starting on page 14) or for brands or models not listed
• Favorite Channel Scan for easy channel surfing
• Mode reassignment to control duplicate types of devices
• Volume Lock to assign volume controls to individual devices or to
one global device
• Commercial Skip feature allows you to channel surf during
commercial interruptions of your favorite programs
• Pre-programmed database with the world’s largest and most
efficient group of infrared codes insures device compatibility
• Internal modem for upgrading device codes over the telephone
• A low battery icon to notify you when batteries are getting low
• Backlighting feature to aid operation in low ambient light
The One For All A/V LCD 8-Device With Learning Universal Remote
Control (URC-8910) requires four (4) new AAA alkaline batteries
(not included) and easy programming to control your devices. For
best results, please read and perform all instructions listed here.
Also, keep these instructions for future reference.
3
INSTALLING BATTERIES
❶
❷
❸
1.
On the back of the URC-8910 remote control, push
the tab and lift off the battery cover.
2.
Obtain four (4) new AAA alkaline batteries. Match
the + and – marks on the batteries to the + and –
marks in the case, and then insert the new batteries.
3.
Align the cover key with the case opening and
replace the cover until it locks.
4.
If batteries are inserted correctly, the entire LCD
will turn on.After 5 seconds of inactivity, the remote
control will turn itself off to conserve battery life.
5.
Perform the steps in Setting The Clock (on the next
page) to set the correct time.
NOTE: When a battery icon appears in the display (see page 7, Key Charts,
LCD), the batteries are low. Simply replace them and the URC-8910 remote
control will be restored to full functionality, complete with your favorite settings.
4
SETTING THE CLOCK
1.
On the URC-8910 remote control, press and hold
SET until you see the display change from the default
device and time to [CODE SET].
NOTE: Default values for device, its code, and time are
shown above.Your remote control settings may be different.
NOTE: If you wish to exit the programming mode at any
time, press EXIT once. You will see an [EXIT] message as the
remote control returns to normal operation.
NOTE: If you see an [INVALID] message, you have inadvertently pressed an incorrect key. Simply note your error and
continue programming.
2.
Press the ▲ key five times until you see the display
change to [CLOCK SET].
(x 5)
NOTE: If you go past [CLOCK SET] , press the ▼ key one or
more times to return to it.
3.
SELECT
Press SELECT once to begin programming.You will
see the display change to the current time.
4.
Press the ▲ key one or more times until you see the
desired hour (a.m. or p.m.).
5.
Press the ▼ key one or more times until you see the
desired minute.
6.
SELECT
Once the time is correctly set, press SELECT once to
accept the values. The display will confirm your
entry with [SUCCESS] and then [EXIT SETUP].
The URC-8910 remote control will return to
normal operation.
5
FEATURES AND FUNCTIONS
Use the illustration below to locate features on the URC-8910 remote
control and then study the Key Charts (on the next three pages) to
learn how they function.
ND SOUN
RROU
D
SU
SELECT
6
Key Charts
The LED (red light) blinks to show that the
remote control is working and sending signals.
The LCD (Liquid Crystal Display)
provides 15 alphanumeric characters that display status messages
during remote control operation
and programming.Also, one or
more icons appear in the LCD to
indicate the following conditions:
or
Morning or Afternoon Time
Low Battery
IR Signal Transmission
Press TV, VCR, DVD, AUX, SAT, CBL,
RCVR/AMP, or CD once to select a
desired home entertainment
device to control.
After programming, press HOME
THEATER once to select the home
theater mode. (See Using The Home
Theater Mode on page 43.)
▲
In the CD mode, use SELECT to select a
compact disc. Use ▲ (or ▼) to select the next
(or previous) CD. Use (or ) to select the
next (or previous) track.
In the RCVR/AMP mode, use SELECT to
set the surround sound. Use ▲ (or ▼) to
adjust the volume higher (or lower). Use
(or ) to adjust the balance left (or right).
▲
SELECT
Use the cursor keys (▲ , ▼, or ) to move
the cursor in the program guide and menu
screens. Use SELECT to choose options from
your selected device’s menu or guide.
▲
D
RROUN SOUND
SU
▲
▲
Press POWER once to turn on or off the
selected device.
▲
Press MENU once to display your selected
device’s main menu.
Use GUIDE to display your selected device’s
program guide or setup menu.
continued on next page...
7
FEATURES AND FUNCTIONS
Key Charts (continued)
Use EXIT to exit from your selected device’s
guide or menu.
Use INFO to display the current channel and
program information.
Use VOL+ (or VOL-) to raise (or lower) the
audio volume.
Press MUTE once to turn the audio off
or on.
In the TV, VCR, DVD, SAT, and CBL modes,
use FAV to scan favorite channels and/or all
channels.(See Using Channel Scan and
Programming Favorite Channel Scan on page
41.)
Use CH+ (or CH-) to select the next higher (or
lower) channel.
Press PREV once to recall the last-viewed
channel and to page back one screen on the
main menu.
In the CD mode, use PREV to turn random
play on or off.
In the RCVR/AMP mode, use PREV to select
the receiver band.
Use the keypad (1 ~ 9 and 0) to
directly select channels (e.g., 009 or
031).
In the RCVR/AMP mode, use the
keypad (1 ~ 9 and 0) to select audio
sources 1 through 10.
Press ENTER once after entering the channel
numbers on some TVs.
In the CD mode, use ENTER to add 10 to the
digit entry (e.g., ENTER and 7 is 17).
Use TV/VID to switch the TV’s input to view
TV or video programs.
8
Use the transport keys to control your
VCR,DVD or CD player,or VOD (Video
On Demand) if available on your cable
or satellite service.
To record a VCR program, press REC
twice.
Use SLEEP to activate your device’s sleep
timer (not available for all devices).
After programming, press M1 ~ M3 once to
run a desired macro (see Using Macros on
page 34).
After programming, press L1 ~ L4
once to activate a learned function.
(See Using Learning on page 30.)
Use PIP to switch the Picture-In-Picture
feature on or off (if available on your TV).
Use MOVE to move the window picture
to different positions in the main picture.
Use SWAP to switch images and sound
between the main and window pictures.
After programming, use COM SKIP to skip
commercials on selected devices (i.e., TV, VCR,
DVD, CBL, and SAT). (See Using Commercial
Skip on page 48.)
Use to turn on or off the key backlight.
When this feature is activated, keys will
remain backlit for 5 seconds after the last key
press. In the setup mode, backlighting
will remain on for 30 seconds.
Use SET for all programming sequences.
9
SETTING UP YOUR COMPONENTS
The URC-8910 remote control is preprogrammed at the factory to
operate an RCA TV and VCR, a Motorola (GI) cable converter, an RCA
satellite receiver, a Pioneer CD player, a Toshiba DVD player, a Pioneer
audio receiver/ amplifier, and a One For All home automation device.
To control devices other than the default brands, perform the following steps and repeat them as needed for each device to be programmed; otherwise skip this section:
NOTE: For TV/VCR Combo control, see “Programming TV/VCR Combo
Control” on page 12.
1.
Turn on a device (e.g.,VCR or DVD player) and, if
applicable, insert media (e.g., cassette or disc).
NOTE: Please read steps 2 through 8 completely before
proceeding. Highlight or write down the codes and device
you wish to program before starting step 2.
2.
On the URC-8910 remote control, press and hold
SET until you see the display change from the current device and time to [CODE SET].
NOTE: The device, its code, and time are examples. Your
remote control settings may be different.
NOTE: To exit programming at any time, press EXIT once or
allow 30 seconds of inactivity to lapse. You will see [EXIT
SETUP] as the remote control returns to normal operation.
NOTE: [INVALID] means you have inadvertently pressed an
incorrect key. Note your error and continue programming.
3.
SELECT
Press SELECT once to begin programming.You will
see the display change to the last-selected device
and its current code (e.g., TV and 0051).
Press a desired device key once (e.g., VCR).You will
see the display change to the desired device and its
current code (e.g., VCR and 0035).
4.
NOTE: Use the AUX key to program control of home
automation devices, video accessories, audio services, and
other audio or video devices. Alternately, use the AUX key to
program control of a second device type (e.g., a second VCR;
see “Re-assigning Device Keys” on page 37).
5.
SELECT
Use the Manufacturer’s Codes (starting on page 14)
to locate the type of device and brand name. Then
use the keypad to enter the first four-digit code for
your device and press SELECT once.
10
For example, to enter the first GE VCR code (on
page 17), press 0 twice, 6 once, 0 once, and then
SELECT once.
If the code is entered correctly, you will see the
[SUCCESS] message.
6.
Press EXIT to exit the programming mode.You will
see an [EXIT SETUP] message as the URC-8910
remote control returns to normal operation.
7.
To verify the code works, aim the URC-8910 remote
control at the desired device, press its device key
once and then press POWER once. The device should
turn off. If it does not respond, repeat steps 2
through 6, trying each code for your brand until you
find one that works. If it still does not work, try
Searching For Your Code on page 27.
NOTE: If the device does not have a POWER key, press the
(Play) key.
8.
Repeat steps 1 through 7 for each device you want
to control. For future reference, write down each
working device code in the boxes below:
TV Code:
VCR Code:
DVD Code:
SAT Code:
CBL Code:
RCVR/AMP
Code:
CD Code:
AUX Code:
Aux. Device
Type:________________________________
11
PROGRAMMING TV/VCR COMBO CONTROL
Perform the following instructions to control a TV/VCR Combo:
1.
Turn on the TV/VCR Combo and insert a video
cassette.
NOTE: Please read steps 2 through 9 completely before proceeding. Highlight or write down the codes and device you
wish to program before starting step 2.
2.
On the URC-8910 remote control, press and hold
SET until you see the display change from the current device and time to [CODE SET].
NOTE: The device, its code, and time are examples.Your
remote control settings may be different.
NOTE: To exit programming at any time, press EXIT once or
allow 30 seconds of inactivity to lapse. You will see [EXIT
SETUP] as the remote control returns to normal operation.
NOTE: [INVALID] means you have inadvertently pressed an
incorrect key. Note your error and continue programming.
3.
SELECT
Press SELECT once to begin programming.You will
see the display change to the last-selected device
and its current code (e.g., TV and 0051)
4.
Press VCR once.You will see the display change to
[VCR] and its current code.
5.
Use the Setup Codes For TV/VCR Combos (on
page 19) to locate the type of device and brand
name. Then use the keypad to enter the first fourdigit code for your device and press SELECT once.
SELECT
For example, to enter the first Sony TV/VCR Combo
code on page 23, press 0 four times and then
SELECT once.
If the code is entered correctly, you will see the
[SUCCESS] message.
NOTE: If your TV/VCR Combo has a separate TV code, you
will also need to perform step 6.
12
6.
(Optional) Skip this step if your TV/VCR Combo
does not have a separate TV code. Otherwise, press
TV once.You will see the display change to [TV] and
its current code.
Use the keypad to enter the separate TV code for
your device.
7.
Press EXIT to exit the programming mode.You will
see [EXIT SETUP] as the URC-8910 remote control
returns to normal operation.
8.
To verify the code works, aim the URC-8910 remote
control at the desired device, press VCR once and
then press POWER once. The TV/VCR Combo
should turn off. If it does not respond, repeat steps 2
through 8, trying each code for your brand until you
find one that works. If it still does not work, try
Searching For Your Code on page 27.
NOTE: If the device does not have a POWER key, press the
(Play) key.
NOTE: For VCR/TV Combos programmed with separate TV
codes, TV volume is controlled by pressing VCR first and
then TV. After that, use VOL+ (or VOL-) to raise (or lower)
the TV volume. For other alternatives on controlling volume
keys, see “Changing Volume Lock” on page 32 or “Using
Keymover” on page 38.
9.
For future reference, write down the working
TV/VCR combo code in the below boxes:
TV/VCR Code:
TV Code
(if used):
13
MANUFACTURER’S CODES
Setup Codes For TVs:
AOC
Admiral
Aiko
Aiwa
Akai
Alaron
Ambassador
America Action
Ampro
Anam
Audiovox
Baysonic
Belcor
Bell & Howell
Bradford
Brockwood
Broksonic
CXC
Candle
Carnivale
Carver
Celebrity
Cineral
Citizen
Concerto
Contec
Craig
Crosley
Crown
Curtis Mathes
Daewoo
Daytron
Denon
Dumont
Dwin
Electroband
Emerson
Envision
Fisher
Fujitsu
Funai
Futuretech
GE
Gibralter
GoldStar
Gradiente
0030, 0019
0093, 0463
0092
0701
0030
0179
0177
0180
0751
0180
0451, 0180, 0092, 0623
0180
0019
0154, 0016
0180
0019
0236, 0463
0180
0030, 0056
0030
0054
0000
0451, 0092
0060, 0030, 0056, 0092
0056
0180
0180
0054
0180
0047, 0054, 0154, 0051, 0451, 0093, 0060, 0030, 0145, 0056,
0016, 0166, 0466, 0747, 1147, 1347
0451, 0019, 0092, 0623, 0624
0019
0145
0017, 0019
0720, 0774
0000
0154, 0236, 0463, 0180, 0178, 0019, 0179, 0177,0623, 0624
0030
0154
0179, 0683
0180, 0179, 0171
0180
0047, 0051, 0451, 0093, 0178, 0021, 0747, 1147, 1347
0017, 0030, 0019
0030, 0178, 0019, 0056
0053, 0056
14
Grunpy
Hallmark
Harley Davidson
Harman/Kardon
Harvard
Hitachi
Infinity
Inteq
JBL
JCB
JVC
KEC
KTV
Kenwood
Konka
LG
LXI
Logik
Luxman
MGA
MTC
Magnavox
Majestic
Marantz
Matsushita
Megatron
Memorex
Midland
Minutz
Mitsubishi
Motorola
Multitech
NAD
NEC
NTC
Nikko
Onwa
Optimus
Optonica
Orion
Panasonic
Penney
Philco
Philips
Pilot
Pioneer
Portland
Princeton
Prism
0180, 0179
0178
0179
0054
0180
0145, 0056, 0016, 0151
0054
0017
0054
0000
0053
0180
0180, 0030
0030, 0019
0628, 0632, 0638, 0703, 0707
0056
0047, 0054, 0154, 0156, 0178, 0747
0016
0056
0150, 0030, 0178, 0019
0060, 0030, 0019, 0056
0054, 0030, 0179, 1254
0016
0054, 0030
0250
0178, 0145
0154, 0250, 0463, 0150, 0178, 0179, 0056, 0016
0047, 0017, 0051, 0747
0021
0093, 0150, 0178, 0019
0093
0180
0156, 0178, 0166
0030, 0019, 0056
0092
0030, 0178, 0092
0180
0154, 0250, 0166
0093
0236, 0463, 0179
0051, 0250
0047, 0156, 0051, 0060, 0030, 0178, 0021, 0019, 0056, 0747,
1347
0054, 0463, 0030, 0145, 0019
0054
0030, 0019
0166, 0679
0019, 0092
0717
0051
continued on next page...
15
MANUFACTURER’S CODES
Setup Codes For TVs (continued):
Proscan
Proton
Pulsar
Quasar
RCA
RadioShack
Realistic
Runco
SSS
Sampo
Samsung
Sansei
Sansui
Sanyo
Scimitsu
Scotch
Scott
Sears
Semivox
Semp
Sharp
Shogun
Signature
Sony
Soundesign
Squareview
Starlite
Supreme
Sylvania
Symphonic
TMK
TNCi
Tandy
Technics
Technol Ace
Techwood
Teknika
Telefunken
Toshiba
Vector Research
Victor
Vidikron
Vidtech
Wards
White Westinghouse
Yamaha
0047, 0747
0178, 0466
0017, 0019
0051, 0250
0047, 0051, 0093, 0019, 0090, 0679, 0747, 1047, 1147, 1247,
1347, 1447
0047, 0154, 0180, 0030, 0178, 0019, 0056, 0747
0154, 0180, 0030, 0178, 0019, 0056
0017, 0030, 0603
0180, 0019
0030
0060, 0030, 0178, 0019, 0056
0451
0463
0154
0019
0178
0236, 0180, 0178, 0019, 0179
0047, 0054, 0154, 0156, 0178, 0179, 0056, 0171, 0747
0180
0156
0093, 0688
0019
0016
0000
0180, 0178, 0179
0171
0180
0000
0054, 0030
0180, 0171
0178, 0056, 0177
0017
0093
0051, 0250
0179
0051, 0056
0054, 0180, 0150, 0060, 0019, 0179, 0056, 0016, 0092
0056
0154, 0156, 0060, 1256
0030
0053
0054
0178, 0019
0054, 0030, 0178, 0021, 0019, 0179, 0056, 0016
0463, 0623, 0624
0030, 0019
16
Zenith
0017, 0463, 0016, 0092, 0624
Setup Codes For VCRs:
Admiral
Adventura
Aiko
Aiwa
Akai
America Action
American High
Asha
Audiovox
Beaumark
Bell & Howell
Broksonic
CCE
Calix
Canon
Carver
Cineral
Citizen
Colt
Craig
Curtis Mathes
Cybernex
Daewoo
Denon
Dynatech
Electrohome
Electrophonic
Emerex
Emerson
Fisher
Fuji
Funai
GE
Garrard
Go Video
GoldStar
HI-Q
Harley Davidson
Harman/Kardon
Harwood
Hitachi
Hughes Network Sys.
JVC
Jensen
KEC
0048, 0209
0000
0278
0037, 0000
0041
0278
0035
0240
0037
0240
0104
0184, 0121, 0209, 0002, 0479
0072, 0278
0037
0035
0081
0278
0037, 0278
0072
0037, 0047, 0240, 0072
0060, 0035, 0041, 0162, 0760
0240
0045, 0278
0042
0000
0037
0037
0032
0037, 0184, 0000, 0121, 0043, 0209, 0002, 0278, 0479
0047, 0104
0035, 0033
0000
0060, 0035, 0048, 0240, 0760
0000
0432
0037, 0038
0047
0000
0081, 0038
0072
0000, 0042, 0041
0042
0067, 0041
0041
0037, 0278
continued on next page...
17
MANUFACTURER’S CODES
Setup Codes For VCRs (continued) :
Gradiente
KLH
Kenwood
Kodak
LXI
Lloyd’s
Logik
MEI
MGA
MGN Technology
MTC
Magnasonic
Magnavox
Magnin
Marantz
Marta
Matsushita
Memorex
Minolta
Mitsubishi
Motorola
Multitech
NEC
Nikko
Noblex
Olympus
Optimus
Orion
Panasonic
Penney
Pentax
Philco
Philips
Pilot
Pioneer
Polk Audio
Profitronic
Proscan
Protec
Pulsar
Quasar
RCA
RadioShack
Radix
Randex
Realistic
0000
0072
0067, 0041, 0038
0035, 0037
0037
0000
0072
0035
0240, 0043
0240
0240, 0000
0278
0035, 0039, 0081, 0000, 0149, 0563
0240
0035, 0081
0037
0035, 0162
0035, 0037, 0048, 0039, 0047, 0240, 0000, 0104, 0209, 0162,
0479, 1037, 1162, 1262
0042
0048, 0067, 0043
0035, 0048
0000, 0072
0104, 0067, 0041, 0038
0037
0240
0035
0037, 0048, 0104, 0162, 0432, 1048, 1062, 1162, 1262
0184, 0209, 0002, 0479
0035, 0162, 0225, 0616, 1062, 1162, 1262, 1362
0035, 0037, 0240, 0042, 0038
0042
0035, 0209, 0479
0035, 0081, 0618, 1081, 1181
0037
0067
0081
0240
0060, 0760
0072
0039
0035, 0162, 1162
0060, 0035, 0048, 0240, 0042, 0149, 0760
0000, 1037
0037
0037
0035, 0037, 0048, 0047, 0000, 0104
18
ReplayTV
Runco
STS
Samsung
Sanky
Sansui
Sanyo
Scott
Sears
Semp
Sharp
Shintom
Shogun
Singer
Sony
Sylvania
Symphonic
TMK
Tatung
Teac
Technics
Teknika
Thomas
Tivo
Toshiba
Totevision
Unitech
Vector
Vector Research
Video Concepts
Videosonic
Wards
White Westinghouse
XR-1000
Yamaha
Zenith
0614, 0616
0039
0042
0240, 0045
0048, 0039
0000, 0067, 0209, 0041, 0479
0047, 0240, 0104
0184, 0045, 0121, 0043
0035, 0037, 0047, 0000, 0042, 0104
0045
0048
0072
0240
0072
0035, 0032, 0000, 0033, 0636, 1032
0035, 0081, 0000, 0043
0000
0240
0041
0000, 0041
0035, 0162
0035, 0037, 0000
0000
0618, 0636
0045, 0043
0037, 0240
0240
0045
0038
0045
0240
0060, 0035, 0048, 0047, 0081, 0240, 0000, 0042, 0072, 0149,
0760
0209, 0072, 0278
0035, 0000, 0072
0038
0039, 0000, 0209, 0033, 0479
MANUFACTURER’S CODES
Setup Codes For TV/VCR Combos:
Broksonic
Citizen
Colt
Curtis Mathes
Daewoo
Emerson
Funai
0002, 0479 (for TV use 0463)
0278
0072
0035 (for TV use 0051)
0278 (for TV use 0624)
0002, 0278 (for TV use 0624), 0294 (for TV use 0236),
0479 (for TV use 0463)
0000
continued on next page...
19
MANUFACTURER’S CODES
Setup Codes For TV/VCR Combos :
GE
GoldStar
Harley Davidson
Hitachi
Lloyd’s
Magnasonic
Magnavox
Magnin
Memorex
MGA
Mitsubishi
Optimus
Orion
Panasonic
Penney
Quasar
RadioShack
RCA
Sansui
Sanyo
Sears
Sharp
Sony
Sylvania
Symphonic
Thomas
White Westinghouse
Zenith
0035 (for TV use 0051), 0048 (for TV use 0093),
0060 (for TV use 0047), 0240
0037 (for TV use 0056)
0000
0000
0000
0278, 0563
0000, 0081 (for TV use 0054)
0240
0037, 0162 (for TV use 0250), 1037, 1162, 1262
0240
0048 (for TV use 0093)
0162 (for TV use 0250), 1162, 1262
0000, 0479 (for TV use 0463)
0035 (for TV use 0051), 0162 (for TV use 0250), 1162,
1262
0035 (for TV use 0051), 0037 (for TV use 0056), 0240
0035 (for TV use 0051), 0162 (for TV use 0250)
1037
0035 (for TV use 0051), 0048 (for TV use 0093),
0060 (for TV use 0047), 0240
0000, 0479 (for TV use 0463)
0240
0000, 0037 (for TV use 0056)
0048 (for TV use 0093)
0000, 0032 (for TV use 0000)
0081 (for TV use 0054)
0000, 0563
0000
0278 (for TV use 0624)
0000, 0637 (for TV use 0624)
MANUFACTURER’S CODES (continued)
Setup Codes For DVD Players:
Aiwa
Apex
Denon
Emerson
Fisher
GE
GPX
Go Video
Gradiente
Harman/Kardon
Hitachi
0641
0672
0490, 0634
0591
0670
0522, 0717
0769
0715
0651
0582
0573, 0664
20
Hiteker
JVC
Kenwood
Konka
Magnavox
Marantz
Mitsubishi
Onkyo
Optimus
Oritron
Panasonic
Philips
Pioneer
Princeton
Proscan
RCA
Samsung
Sanyo
Sharp
Sherwood
Sony
Technics
Techwood
Theta Digital
Toshiba
Yamaha
Zenith
0672
0558, 0623
0534, 0682
0711, 0719, 0720, 0721
0503, 0675
0539
0521
0503, 0627
0571
0651
0490, 0632
0503, 0539
0525, 0571, 0632
0674
0522
0522, 0571, 0704, 0717
0573
0670
0630
0633
0533
0490
0692
0571
0503
0490, 0545
0503, 0591
Setup Codes for Cable Converters:
ABC
Americast
Bell South
General Instrument
GoldStar
Hamlin
Jerrold
Memorex
Motorola
Pace
Panasonic
Paragon
Philips
Pioneer
Pulsar
Quasar
Regal
Runco
Samsung
0003, 0017
0899
0899
0476, 0810
0144
0009, 0273
0003, 0476, 0276, 0810
0000
0476, 1106
0237
0000, 0107
0000
0305, 0317
0144, 0533, 0877
0000
0000
0273, 0279
0000
0144
continued on next page...
21
MANUFACTURER’S CODES
Setup Codes for Cable Converters (continued):
Scientific Atlanta
Sony
Starcom
Supercable
Toshiba
Zenith
0477, 0017, 0877
1006
0003
0276
0000
0000, 0525, 0899
Setup Codes For Satellite Receivers:
AlphaStar
Chaparral
Echostar
Expressvu
GE
General Instrument
HTS
Hitachi
Hughes Network Sys.
JVC
Magnavox
Memorex
Mitsubishi
Next Level
Panasonic
Philips
Proscan
RCA
RadioShack
Samsung
Sony
Star Choice
Toshiba
Uniden
Zenith
0772
0216
0775, 1005
0775
0566
0869
0775
0819
0749, 1142, 1749
0775
0724, 0722
0724
0749
0869
0701, 0247
0749, 0724, 0722, 1076, 1142
0392
0566, 0143, 0392, 0855
0869
1109
0639
0869
0749, 0790
0724, 0722
0856
Setup Codes For CD Players:
Aiwa
Burmester
California Audio Labs
Carver
DKK
Denon
Emerson
Fisher
Garrard
Genexxa
Harman/Kardon
0157, 0124
0420
0029, 0303
0157, 0179, 0437
0000
0003, 0873
0305
0179, 0174
0420, 0393
0032, 0305
0157, 0173
22
Hitachi
JVC
Kenwood
Krell
LXI
Linn
MCS
MTC
Magnavox
Marantz
Mission
NSM
Nikko
Onkyo
Optimus
Panasonic
Parasound
Philips
Pioneer
Polk Audio
Proton
QED
Quasar
RCA
Realistic
Rotel
SAE
Sansui
Sanyo
Scott
Sears
Sharp
Sherwood
Sonic Frontiers
Sony
Soundesign
Tascam
Teac
Technics
Victor
Wards
Yamaha
Yorx
0032
0072
0028, 0037, 0190, 0626, 0681, 0826
0157
0305
0157
0029
0420
0157, 0305
0029, 0157, 0180, 0626
0157
0157
0174
0101, 0868
0000, 0032, 0179, 0305, 0037, 0420, 0145, 0468, 0437, 1063
0029, 0303
0420
0157, 0626
0032, 0305, 0468, 1062, 1063
0157
0157
0157
0029
0032, 0179, 0305, 0053, 0468, 0764, 1062
0179, 0420, 0180
0157, 0420
0157
0157, 0305
0179
0305
0305
0037, 0180, 0861
0180, 1067
0157
0000, 0185, 0490
0145
0420
0420, 0393, 0174, 0180
0029, 0303
0072
0157, 0053
0036, 0187, 0888
0461
Setup Codes for Audio Amplifiers:
GE
Harman/Kardon
JVC
Luxman
0078
0892
0331
0165
ontinued on next page...
23
MANUFACTURER’S CODES
Setup Codes for Audio Amplifiers (continued):
Marantz
Nakamichi
Optimus
Philips
Polk Audio
Realistic
Sansui
Sony
Soundesign
Victor
Wards
Yamaha
0321, 0892
0321
0395
0892
0892
0395
0321
0689
0078
0331
0078
0354
Setup Codes For Audio Cassette Decks:
Sony
0243
Setup Codes for Audio Receivers:
ADC
Aiwa
Bose
Capetronic
Carver
Compaq
Denon
Harman/Kardon
Hewlett Packard
JBL
JVC
Kenwood
MCS
Magnavox
Marantz
Onkyo
Optimus
Panasonic
Philips
Pioneer
Proscan
Quasar
RCA
Sansui
Sharp
Sony
Soundesign
Sunfire
0531
0121, 1089, 1405
1229
0531
1089, 1189
1136
1104, 1160
0110
1181
0110
0074
0186, 1027, 1313, 1569, 1570
0039
0531, 1089, 1189
0039, 1089, 1189
0135
0531, 0670, 0186, 1023
0039, 1518
1089, 1189, 1269
0531, 0014, 0150, 0630, 1023
1254
0039
0531, 1023, 1254
1089
0186
1058, 1158, 1258
0670
1313
24
Technics
Thorens
Victor
Wards
Yamaha
0039, 1308, 1309, 1518
1189
0074
0014
0176, 0186, 1176
Setup Codes For Audio Turntables:
Aiwa
Carver
Magnavox
Marantz
Philips
0188
0188
0188
0188
0188
Setup Codes For Misc. Audio Services:
Jerrold
Scientific Atlanta
Starcom
0459, 0520
0460
0459
Setup Codes For DAT (Digital Audio Tape) Recorders:
Carver
Harman/Kardon
Magnavox
Marantz
Philips
0158
0158
0158
0158
0158
Setup Codes For LD (Laser Disc) Players:
Denon
Mitsubishi
NAD
Optimus
Pioneer
0059
0059
0059
0059
0059
Setup Codes For Home Automation:
GE
One For All
RadioShack
Security System
Universal X10
X10
0240
0167
0240
0167
0167
0167
25
MANUFACTURER’S CODES (CONTINUED)
Setup Codes For Video Accessories:
Archer
GC Electronics
Jebsee
Magnavox
Panasonic
Philips
Pioneer
RadioShack
Sensory Science
Sharp
Sony
0160
0160
0160
0818
1120
0818
1010
0160
1126
1010
0850
26
SEARCHING FOR YOUR CODE
If your device does not respond to the URC-8910 remote control
after trying all codes listed for your brand, or if your brand is not
listed at all, try manually searching for your code.
For example, to manually search for a code for your TV:
1.
Turn on the TV.
2.
On the URC-8910 remote control, press and hold
SET until you see the display change from the
current device and time to [CODE SET].
NOTE: The device, its code, and time are examples. Your
remote control settings may be different.
NOTE: To exit programming at any time, press EXIT once or
allow 30 seconds of inactivity to lapse. You will see [EXIT
SETUP] as the remote control returns to normal operation.
NOTE: [INVALID] means you have inadvertently pressed an
incorrect key. Note your error and continue programming.
3.
Press the ▼ key once until you see the display
change to [MAN SEARCH].
NOTE: If you go past [MAN SEARCH] , press the ▲ key one or
more times to return to it.
4.
SELECT
Press a desired device key once (e.g., TV).You will
see the display change to the desired device and the
first code in the manual search list (e.g., TV and
0047).
5.
6.
Press SELECT once to begin programming.You will
see the display change to the last-selected device
and its code (e.g., VCR and 0035).
SELECT
Aim the URC-8910 remote control at the device
(e.g., TV) and press SELECT once.You will see the
LED (red light) blink and the
(IR) icon flash
indicating IR codes are being transmitted.
continued on next page...
27
SEARCHING FOR YOUR CODE (continued)
NOTE: In the manual search mode, the URC-8910 remote
control will send IR codes from its library to the selected
device, starting with the most popular code first.
If the device (e.g., TV) turned off, skip to the next
step. If it did not turn off, aim the URC-8910 remote
control at the device (e.g., TV) and press the ▲ key
once to advance the manual search to the next code
(e.g., TV and 0054).Again you will see the LED (red
light) blink and the
(IR) icon flash.
7.
Repeat this step as often as needed until you find a
code that turns off the device.
8.
SELECT
To save the working code, press SELECT once. The
display will confirm your entry with [SUCCESS] and
then [EXIT SETUP].
The URC-8910 remote control will return to
normal operation.
NOTE: For future reference, write down the working device
code in the appropriate boxes on page 11.
9.
To perform a manual code search for another
device, repeat steps 1 through 8, but this time (in
step 5) substitute the appropriate device key for the
device you are searching for.
NOTE: If you have not found a working device code after trying the above
procedure, please contact our customer service center to upgrade your
One For All A/V LCD 8-Device With Learning Universal Remote Control
(URC-8910). See “About Upgrading” on page 51.
28
USING LEARNING
Program the learning keys (L1~ L4) to add functions that are
unique to your home entertainment devices (e.g.,VCR Tracking Up
or Down). However, there are some considerations:
• Your original remote control must be in working order for the
learning feature to work properly.
• Learned keys are mode specific, so each one can store a unique
function for each mode.
• Learned keys can be used in macros (see Using Macros on page 34).
• Although dedicated keys (L1~ L4) are provided for storing
learned functions, you can also use any key (except keys for
devices and programming) for learning. However, using them as
learned keys will overwrite their original functions.
• For optimum learning, avoid high levels of ambient light such as
natural sunlight or energy-efficient fluorescent lights.
NOTE: Please have your original remote controls handy before programming
learning. Be sure to press each key within 5 seconds of the previous entry.
If not, the URC-8910 remote control will exit the programming mode.
Programming A Learning Key
1.
On the URC-8910 remote control, press and hold
SET until you see the display change from the current device and time to [CODE SET].
NOTE: The device, its code, and time are examples. Your
remote control settings may be different.
NOTE: To exit programming at any time, press EXIT once or
allow 30 seconds of inactivity to lapse. You will see [EXIT
SETUP] as the remote control returns to normal operation.
NOTE: [INVALID] means you have inadvertently pressed an
incorrect key. Note your error and continue programming.
2.
Press the ▼ key twice until you see the display
changes to [IR LEARN].
(x 2)
NOTE: If you go past [IR LEARN] , press the ▲ key one or
more times to return to it.
3.
SELECT
Press SELECT once to begin programming.You will
see the display change to the last-selected device
(e.g., TV).
continued on next page...
29
USING LEARNING
Programming A Learning Key (continued)
4.
Press a device key once (e.g., TV) to assign a desired
mode for learning.
5.
Select an open learning key (e.g., L1) and press it
once.You will see the display change to [LEARNING]
and the LED (red light) will turn on for 5 seconds.
6.
Place your original remote control (e.g., TV remote
control) head-to-head (about 2" apart) from the
URC-8910 remote control.
2"
7.
On your original remote control, press and hold the
key (i.e., feature) to be learned until you see [SUCCESS] appear on the URC-8910 remote control. The
display will return to device mode you selected for
learning (e.g., TV).
If the key was not learned, you will see an [ERROR]
message instead.
Repeat steps 5 through 7 as needed to achieve
[SUCCESS].
8.
To learn functions onto other learning keys (e.g., L2
~ L4), repeat steps 4 through 7 for each key.
9.
Press EXIT to exit the programming mode.You will
see an [EXIT SETUP] message as the remote control
returns to normal operation.
10.
To test a learned feature, aim the URC-8910 remote
control at the desired device and press its device key
once (e.g., TV, where the learning mode was
assigned). Then press the learning key (e.g., L1)
30
where the learned feature is stored. The feature
should activate. If not, try the programming the
learning key again, starting with step 1 (on page 29).
Deleting A Function From A Learning Key
1.
On the URC-8910 remote control, press and hold
SET until you see the display change from the current device and time to [CODE SET].
NOTE: The device, its code, and time are examples. Your
remote control settings may be different.
NOTE: To exit programming at any time, press EXIT once or
allow 30 seconds of inactivity to lapse. You will see [EXIT
SETUP] as the remote control returns to normal operation.
NOTE: [INVALID] means you have inadvertently pressed an
incorrect key. Note your error and continue programming.
2.
Press the ▼ key three times until you see the display
change to [IR DELETE].
(x 3)
NOTE: If you go past [IR DELETE] , press the ▲ key one or
more times to return to it.
3.
SELECT
Press SELECT once to begin programming.You will
see the display change to the last-selected device
(e.g., TV).
4.
Press a device key once (e.g., TV) for the mode that
contains the learned function.
5.
Press learning key once (e.g., L1) where the feature
(to be deleted) is stored.You will see the display
change to [DELETED] and then return to last-selected
mode (e.g., TV).
6.
If desired, repeat steps 4 and 5 to delete other
learned functions.
7.
Press EXIT to exit the programming mode.You will
see an [EXIT SETUP] message as the URC-8910
remote control returns to normal operation.
31
USING VOLUME LOCK
In its default (unlocked) state, the URC-8910 remote control allows
each device to control its own volume only in its own mode (e.g., TV
volume in the TV mode, VCR volume in VCR mode, etc.). However,
using our Volume Lock feature, you can lock the volume controls for
each device to all modes (e.g., RCVR/AMP volume in all modes).
Moreover, using the Volume Unlock feature (see the next page),
you can further customize the settings so that a device’s volume
controls are unlocked in one mode, but remain locked in all other
modes (e.g., TV volume in the TV mode and RCVR/AMP volume in
other modes).
Programming Volume Lock
1.
On the URC-8910 remote control, press and hold
SET until you see the display change from the current device and time to [CODE SET].
NOTE: The device, its code, and time are examples. Your
remote control settings may be different.
NOTE: To exit programming at any time, press EXIT once or
allow 30 seconds of inactivity to lapse. You will see [EXIT
SETUP] as the remote control returns to normal operation.
NOTE: [INVALID] means you have inadvertently pressed an
incorrect key. Note your error and continue programming.
2.
Press the ▼ key four times until you see the display
change to [VOL LOCK].
(x 4)
NOTE: If you go past [VOL LOCK] , press the ▲ key one or
more times to return to it.
3.
SELECT
Press SELECT once to begin programming.You will
see the display change to [TO MODE].
4.
Press a mode key (e.g., RCVR/AMP) to lock a device’s
volume controls to all modes.You will see the display
change to [SUCCESS] and then [EXIT SETUP] as the
remote control automatically exits the programming
mode and returns to normal operation.
5.
If desired, repeat steps 1 through 4 as needed to lock
volume controls for other devices to all modes.
32
Programming Volume Unlock
1.
On the URC-8910 remote control, press and hold
SET until you see the display change from the
current device and time to [CODE SET].
2.
Press the ▼ key five times until you see the display
change to [VOL UNLOCK].
(x 5)
NOTE: If you go past [VOL UNLOCK] , press the ▲ key one or
more times to return to it.
3.
SELECT
Press SELECT once to begin programming.You will
see the display change to [ALL MODE].
To unlock one mode, skip to step 4. Otherwise press
SELECT once to unlock all modes.You will see the
display change to [UNLOCKED] and then [EXIT SETUP]
as the remote control automatically exits the programming mode and returns to normal operation.
4.
(Optional) Press ▲ (or ▼) once.You will see the
display change to [ONE MODE].
or
SELECT
a. Press SELECT once.You will see the display change
to [SEL MODE].
b. Press a mode key once (e.g., TV) to unlock it.
You will see the display change to [UNLOCKED]
and return to [SEL MODE].
c. If desired, repeat step 4b as needed to unlock
volume controls for other devices. Otherwise,
press EXIT to exit the programming mode.You
will see an [EXIT SETUP] message as the remote
control returns to normal operation.
33
USING MACROS
With programming, the M1 through M3 keys on your URC-8910
remote control can be setup to perform repetitive, time-consuming
operations for easy, convenient access through the press of a single
key. Macro keys are ideal for home theater operations, setting a
favorite channel, guide steps, or other multiple functions you would
like to control with one key press. Moreover, each macro key can
hold up to15 key presses total.
NOTE: Programming a new macro over an existing one will erase the
original macro.
Programming A Favorite Channel
With so many channels available through your cable or satellite
system provider, you can program a macro that directly selects a
favorite channel with one key press. For example, let’s assume your
favorite cable programs are on channel 71. Perform the following
steps to program a macro key for direct access of this channel:
NOTE: This example assumes the TV tuner is connected directly to the cable
line and not through a cable converter.
1.
On the URC-8910 remote control, press and hold
SET until you see the display change from the current device and time to [CODE SET].
NOTE: The device, its code, and time are examples. Your
remote control settings may be different.
NOTE: To exit programming at any time, press EXIT once or
allow 30 seconds of inactivity to lapse. You will see [EXIT
SETUP] as the remote control returns to normal operation.
NOTE: [INVALID] means you have inadvertently pressed an
incorrect key. Note your error and continue programming.
2.
Press the ▼ key six times until you see the display
change to [KEY MACRO].
(x 6)
NOTE: If you go past [KEY MACRO] , press the ▲ key one or
more times to return to it.
3.
4.
SELECT
Press SELECT once to begin programming.You will
see the display change to [SEL MACKEY].
Select an open macro key (e.g., M1) and press it
once.You will see the display change to [ENTER SEQ].
34
5.
Enter a macro sequence of up to 15 keys. For our
example, press the following keys once in this order:
TV - 7- 1
NOTE: If you have access to over 100 channels, add a 0
before the channel numbers (e.g., 0 - 7 -1). If the original
remote control required pressing an Enter key to change the
channel, also press the Enter key after the channel number
(e.g., 0 -7-1-ENTER).
NOTE: An [ERROR] message, followed by [MAX = 15] alerts
you that the macro sequence must be 15 keys or less.
After pressing the first key (in the macro sequence),
you will see the display change to [SEL TO END]. This
message acts as a reminder to use SELECT to end the
sequence (see next step).
6.
SELECT
To end the macro sequence, press and hold SELECT
until you see [SUCCESS] appear in the display,
followed by [EXIT SETUP]. The URC-8910 remote
control will automatically exit the programming
mode and return to normal operation.
Now when you press M1, you will instantly see cable channel 71 on
your TV set.
Programming A Master Power Key With Instant
Channel Selection
A macro key can be programmed to turn on and off your devices as
well. For example, let’s set up a sequence that will turn on the TV
and tune it to channel 3, and then turn on the cable converter and
tune it to a premium channel (e.g., 11).
NOTE: This example assumes all equipment is turned off and that the TV is
connected through the cable converter with TV tuning set to channel 3.
1.
Perform steps 1 through 4 of the previous section,
Programming A Favorite Channel on page 34.
However, this time in step 4, substitute another open
macro key (e.g., M2).
2.
Enter a macro sequence of up to 15 keys. For our
example, press the following keys once in this order:
CBL - POWER - TV - POWER- 0- 3 - CBL- 1- 1
NOTE: If you have access to over 100 channels, add an 0
before each set of channel numbers (e.g., 0 - 0 -3 and 0 - 1 - 1).
If the original remote control required pressing an Enter key
to change the channel, also press the Enter key after each
channel number (e.g., 0 -0-3 -ENTER and 0 - 1 - 1-ENTER).
continued on next page...
35
USING MACROS
Programming A Master Power Key With Instant
Channel Selection (continued)
NOTE: An [ERROR] message, followed by [MAX = 15] alerts
you that the macro sequence must be 15 keys or less.
3.
4.
After pressing the first key (in the macro sequence),
you will see the display change to [SEL TO END].
This message acts as a reminder to use SELECT to
end the sequence (see next step).
SELECT
To end the macro sequence, press and hold SELECT
until you see [SUCCESS] appear in the display,
followed by [EXIT SETUP]. The remote control will
automatically exit the programming mode and
return to normal operation.
Now when you press M2 once, the cable converter and TV will turn
on, the TV will tune to channel 03, and then the cable converter will
tune to channel 11.
Clearing A Macro
1.
Perform steps 1 through 4 of the earlier section,
Programming A Favorite Channel on page 34.
However, this time in step 4, select a macro key you
want to be cleared (e.g., M1 ~ M3).
2.
SELECT
3.
SELECT
Press and hold SELECT to clear the macro key.
You will see the display change to [SEL TO END]. This
message acts as a reminder to use SELECT to end the
sequence (see next step).
Continue pressing SELECT until you see [SUCCESS]
appear in the display, followed by [EXIT SETUP]. The
URC-8910 remote control will automatically exit the
programming mode and return to normal operation.
36
RE-ASSIGNING DEVICE KEYS
The URC-8910 remote control can control a second TV,VCR, DVD
player, or other device by using the Mode Map feature. For example,
to control a TV, a cable converter, and two VCRs, you will need to reassign the unused AUX key to operate the second VCR as follows:
1.
On the URC-8910 remote control, press and hold
SET until you see the display change from the current device and time to [CODE SET].
NOTE: The device, its code, and time are examples. Your
remote control settings may be different.
NOTE: To exit programming at any time, press EXIT once or
allow 30 seconds of inactivity to lapse. You will see [EXIT
SETUP] as the remote control returns to normal operation.
NOTE: [INVALID] means you have inadvertently pressed an
incorrect key. Note your error and continue programming.
2.
Press the ▼ key seven times until you see the display
change to [MODE MAP].
(x 7)
NOTE: If you go past [MODE MAP] , press the ▲ key one or
more times to return to it.
3.
SELECT
Press SELECT once to begin programming.You will
see the display change to [FROM MODE].
4.
Select a mode to be copied (e.g., VCR) and press it
once.You will see the display change to [TO MODE].
5.
Select a mode to be re-assigned (e.g., AUX) and
press it once.You will see the display change to
[SUCCESS], followed by [EXIT SETUP]. The URC-8910
remote control will automatically exit the programming mode and return to normal operation.
6.
The AUX key is now ready to be programmed as
your second VCR. (See Setting Up Your Components
on page 10.)
continued on next page...
37
RE-ASSIGNING DEVICE KEYS (continued)
To re-assign other device keys to the AUX key, repeat steps 1 through
6 on the previous page but substitute the key sequence from the
below chart:
To Re-Assign Device Key
Perform Sequence
AUX as 2nd TV key:
SET*- ▼ (x 7) - SELECT - TV - AUX
AUX as 2nd DVD key:
SET*- ▼ (x 7) - SELECT - DVD- AUX
AUX as 2nd SAT key:
SET*- ▼ (x 7) - SELECT - SAT- AUX
AUX as 2nd CD key:
SET*- ▼ (x 7) - SELECT - CD- AUX
AUX as 2nd CBL key:
SET*- ▼ (x 7) - SELECT - CBL - AUX
AUX as 2nd RCVR/AMP key:
SET*- ▼ (x 7) - SELECT - RCVR/AMP - AUX
*NOTE: Press and hold SET (see step 1 on previous page).
You can also re-assign another unused device key by substituting an
open key for the AUX key in the above chart and performing the
sequence. For example, to re-assign an unused SAT key as a second
CD key, perform SET*- ▼ (x 7) - SELECT - CD - SAT.
USING KEYMOVER
The URC-8910 remote control includes a Keymover feature that
allows you to map (or copy) keys from one mode (i.e., source mode)
to another mode (i.e., destination mode).
NOTE: The following keys cannot be used as a source or destination: TV, VCR,
DVD, AUX, SAT, CBL, RCVR/AMP, CD, HOME THEATER, and SET.
Programming Keymover
For example, if your VCR does not have volume control, try mapping
the volume and mute keys from TV mode to VCR mode as follows:
1.
On the URC-8910 remote control, press and hold
SET until you see the display change from the current device and time to [CODE SET].
NOTE: The device, its code, and time are examples. Your
remote control settings may be different.
NOTE: To exit programming at any time, press EXIT once or
allow 30 seconds of inactivity to lapse. You will see [EXIT
SETUP] as the remote control returns to normal operation.
NOTE: [INVALID] means you have inadvertently pressed an
incorrect key. Note your error and continue programming.
2.
Press the ▼ key eight times until you see the display
change to [KEYMOVER].
(x 8)
38
NOTE: If you go past [KEYMOVER] , press the ▲ key one or
more times to return to it.
3.
SELECT
Press SELECT once to begin programming.You will
see the display change to [FROM MODE].
4.
Select a source mode (e.g., TV) and press it once.You
will see the display change to [FROM KEY].
5.
Select a source key (e.g., VOL+) and press it once.
You will see the display change to [TO MODE].
6.
Select a destination mode (e.g., VCR) and press it
once.You will see the display change to [TO KEY].
7.
Select a destination key (e.g., VOL+) and press it
once.You will see the display change to [SUCCESS],
followed by [EXIT SETUP]. The URC-8910 remote
control will automatically exit the programming
mode and return to normal operation.
8.
Repeat steps 1 through 7 twice more, substituting
VOL– and MUTE as source and destination keys in
steps 5 and 7.
Upon completion of the above procedure, you can now use your
URC-8910 remote control to control the TV’s volume and mute in
the VCR mode, as well as in the TV mode.
Restoring Keymoved Keys to Default Settings
Restoring A Single Keymoved Key
1.
Perform steps 1 through 7 of the previous section,
Programming Keymover on the previous page.
However, this time in step 6, make the destination
mode the same as the source mode (e.g., TV).You
will see the display change to [CLR KMVR].
continued on next page...
39
USING KEYMOVER
Restoring Keymoved Keys to Default Settings
Restoring A Single Keymoved Key (continued)
2.
SELECT
Press SELECT once to clear the keymoved key.You
will see [DELETED] appear in the display, followed by
[EXIT SETUP]. The URC-8910 remote control will
automatically exit the programming mode and
return to normal operation.
Restoring All Keymoved Keys In A Single Mode
1.
2.
Perform steps 1 through 4 of the earlier section,
Programming Keymover on page 38. However, this
time in steps 3 and 4, make the source mode and
source key the same mode (e.g., TV).You will see the
display change to [CLR KMVR].
SELECT
Press SELECT once to clear all keymoved keys from
this mode.You will see [DELETED] appear in the
display, followed by [EXIT SETUP]. The remote control
will automatically exit the programming mode and
return to normal operation.
40
USING CHANNEL SCAN
In the TV, VCR, DVD, SAT, and CBL modes, use the FAV key to start a
3-second scan of all favorite channels (if programmed – see
Programming Favorite Channel Scan below) and/or all channels for
the selected mode.
1.
If Favorite Channel Scan has been set up, skip to
step 2. Otherwise, on the URC-8910 remote control
press TV, VCR, DVD, SAT, or CBL once.
2.
Press FAV once.
• If Favorite Channel Scan has been set up, scanning
of favorite channels will start and, upon completion, continue to scan all channels upward for the
same device.
• If Favorite Channel Scan has not been set up,
scanning will start with the current channel, then
proceed to the next channel up, and continue
until all channels of the selected device is
scanned.You will see the LED (red light) and IR
transmission icon ( ) blink each time a channel
is scanned.
3.
To stop scanning channels at any time, press any key
once (except the backlight key ).
PROGRAMMING FAVORITE CHANNEL SCAN
In the TV, VCR, DVD, SAT, or CBL mode, you can store a list of up to
10 favorite channels, in any order, that will be immediately scanned
when FAV is pressed (see Using Channel Scan above).
NOTE: Only channels of one mode can be stored for Favorite Channel Scan.
1.
On the URC-8910 remote control, press and hold
SET until you see the display change from the current device and time to [CODE SET].
NOTE: The device, its code, and time are examples. Your
remote control settings may be different.
NOTE: To exit programming at any time, press EXIT once or
allow 30 seconds of inactivity to lapse. You will see [EXIT
SETUP] as the remote control returns to normal operation.
NOTE: [INVALID] means you have inadvertently pressed an
incorrect key. Note your error and continue programming.
continued on next page...
41
PROGRAMMING FAVORITE CHANNEL SCAN
(continued)
2.
Press the ▲ key four times until you see the display
change to [FAV CHAN].
(x 4)
NOTE: If you go past [FAV CHAN] , press the ▼ key one or
more times to return to it.
3.
SELECT
4.
SELECT
5.
Press SELECT once to begin programming.You will
see the display change to the last-selected device
(e.g., [VCR]).
Select a mode (e.g., TV) for favorite channel
scanning and press it once. Then press SELECT
once.You will see the display change to [FAV].
Use the keypad to enter a favorite channel number
(e.g., 031). The display will show your entry.
NOTE: If the original remote control required pressing an
Enter key to change the channel, also press the ENTER key
after the channel number (e.g., 0 -3 -1-ENTER). However, the
display will not show the ENTER key.
NOTE: If you made a mistake during entry, press any
number key one or more times until you see the display
clear out. Then try entering the correct numbers again.
SELECT
6.
Press SELECT once.You will see the display clear out,
ready for your next entry.
If desired, repeat step 5 for each favorite channel to
be stored, up to a total of 10 channels.
NOTE: Once the tenth channel is entered, the remote control
will automatically exit programming.
7.
SELECT
(Optional) To exit programming, press and hold
SELECT until you see [SUCCESS] appear in the
display, followed by [EXIT SETUP]. The URC-8910
remote control will automatically exit the programming mode and return to normal operation.
42
USING THE HOME THEATER MODE
The URC-8910 remote control includes a custom Home Theater
mode.After the HOME THEATER key is programmed, it will allow you
to access five groups of remote control keys without having to
change device modes. However, there are some considerations.
• Keymoved and Learned functions, as well Macros programmed
onto keys other than the dedicated macro keys (M1 ~ M3), are
affected by the Home Theater mode. If keys are moved (using
Keymover) or learned onto (using Learning) and they are placed
on keys not within the Control Groups, the keys will be ignored
when pressed.
• A Macro on the POWER key (if applicable) will carry over to the
Home Theater mode.
Control Organization
About Control Groups
For Home Theater programming, the URC-8910 remote control’s
keys are grouped by type of control into the following five
control groups:
(1) Playback Controls: PLAY, STOP, FWD, REW, F.FWD, F.REW,
PAUSE and REC
(2) Audio Controls:
VOL+, VOL- and MUTE
(3) Channel Controls: CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST,
SLEEP, INFO and TV/VID
(5) PIP Controls:
PIP, MOVE and SWAP
▲
MENU, GUIDE, Cursor Controls (▲, ▼, , ),
SELECT and EXIT
▲
(4) Menu Controls:
About Device Groups
Moreover, the URC-8910 remote control’s devices are grouped into
the following five device groups:
(1) Playback Group:
VCR, DVD, CD, CBL, SAT and RCVR/AMP
(2) Audio Group:
TV, VCR, CBL, SAT, DVD, CD, RCVR/AMP and
AUX
(3) Channel Group:
TV, VCR, CBL, SAT, DVD, CD, RCVR/AMP and
AUX
(4) Menu Group:
TV, VCR, CBL, SAT and DVD
(5) PIP Group:
TV, VCR, CBL and SAT
continued on next page...
43
USING THE HOME THEATER MODE
Control Organization
About Device Groups (continued)
The default Device Group settings from the factory is:
(1) Playback Group:
VCR
(2) Audio Group:
TV
(3) Channel Group:
CBL
(4) Menu Group:
CBL
(5) PIP Group:
TV
Programming The Home Theater Mode
For example, let’s assume you have a TV, a cable converter, and a VCR
in your home theater system.You can set up the Home Theater mode
so that selected controls are assigned to these devices as follows:
1.
On the URC-8910 remote control, press and hold
SET until you see the display change from the current device and time to [CODE SET].
NOTE: The device, its code, and time are examples. Your
remote control settings may be different.
NOTE: To exit programming at any time, press EXIT once or
allow 30 seconds of inactivity to lapse. You will see [EXIT
SETUP] as the remote control returns to normal operation.
NOTE: [INVALID] means you have inadvertently pressed an
incorrect key. Note your error and continue programming.
2.
Press the ▲ key three times until you see the display
change to [THEATER].
(x 3)
NOTE: If you go past [THEATER] , press the ▼ key one or
more times to return to it.
3.
SELECT
Press SELECT once to begin programming.You will
see the display change to [PLAYBACK].
NOTE: The program will automatically step through each
Control Group (from Playback to PIP) as you perform steps
3 through 7. However, you can use the ▲ or ▼ keys to navigate to a specific group to make further changes.
44
SELECT
a. Press SELECT once to enter Playback Control
Group assignment.You will see the display change
to the last-selected device (e.g., [TV]).
b. Select a device for Playback Control Group assignment. For this example, press VCR once. This will
assign the entire group of Playback Controls (i.e.,
PLAY, STOP, FF, REW, F.FWD, F.REW, PAUSE and
REC) to the VCR.You will see the display change
to your device choice (e.g., [VCR]).
SELECT
4.
SELECT
c. Press SELECT once to accept the assignment in
step 3b.You will see the display change to the next
Control Group assignment, [AUDIO]).
Press SELECT once to enter Audio Control Group
assignment.You will see the display change to the
last-selected device (e.g., [VCR]).
a. Select a device for Audio Control Group assignment. For this example, press TV once. This will
assign the entire group of Audio Controls (i.e.,
VOL+, VOL-, and MUTE) to the TV.You will see the
display change to your device choice (e.g., [TV]).
SELECT
5.
SELECT
b. Press SELECT once to accept the assignment in
step 4a.You will see the display change to the next
Control Group assignment, [CHANNEL]).
Press SELECT once to enter Channel Control Group
assignment.You will see the display change to the
last-selected device (e.g., [TV]).
continued on next page...
45
USING THE HOME THEATER MODE
Programming The Home Theater Mode
5. (continued)
a. Select a device for Channel Control Group assignment. For this example, press CBL once. This will
assign the entire group of Channel Controls (i.e.,
CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST,
SLEEP, INFO, and TV/VID) to the cable converter.
You will see the display change to your device
choice (e.g., [CBL]).
SELECT
6.
SELECT
b. Press SELECT once to accept the assignment in
step 5b.You will see the display change to the next
Control Group assignment, [MENU]).
Press SELECT once to enter Menu Control Group
assignment.You will see the display change to the
last-selected device (e.g., [CBL]).
▲
SELECT
7.
SELECT
▲
a. Select a device for Menu Control Group assignment.
For this example,press CBL once.This will assign
the entire group of Menu Controls (i.e.,MENU,
GUIDE,Cursor Controls (▲, ▼, , ),SELECT,and
EXIT) to the cable converter.You will see the display
change to your device choice (e.g.,[CBL]).
b. Press SELECT once to accept the assignment in
step 6a.You will see the display change to the next
Control Group assignment, [PIP]).
Press SELECT once to enter PIP Control Group
assignment.You will see the display change to the
last-selected device (e.g., [CBL]).
a. Select a device for PIP Control Group assignment.
For this example, press TV once. This will assign
the entire group of PIP Controls (i.e., PIP, MOVE
and SWAP) to the TV.You will see the display
change to your device choice (e.g., [TV]).
46
SELECT
8.
or
SELECT
b. Press SELECT once to accept the assignment in
step 7a.You will see the display change to the first
Control Group assignment, [PLAYBACK]).
At this point, all Control Groups have been assigned.
To change an assignment, use the ▲ or ▼ keys to
navigate to a specific group and make changes by
repeating the appropriate step (3, 4, 5, 6, or 7).
Otherwise, to exit programming, press and hold
SELECT until you see [SUCCESS] appear in the display, followed by [EXIT SETUP]. The URC-8910
remote control will automatically exit the programming mode and return to normal operation.
Operating The Home Theater Mode
After programming the Home Theater mode (see the previous
section), you simply activate it by pressing HOME THEATER once.
Instantly, groups of URC-8910 remote control keys will be assigned
to their programmed devices.
For the above example (in the previous section), pressing HOME
THEATER once would assign the following keys to the VCR, TV, and
cable converter:
VCR:
PLAY, STOP, FF, REW, F.FWD, F.REW, PAUSE and REC
TV:
VOL+, VOL-, MUTE, PIP, MOVE and SWAP
▲
▲
Cable Converter: CH+, CH-, (Keypad) 0 ~ 9, ENTER, LAST, SLEEP,
INFO, TV/VID, MENU, GUIDE, Cursor Controls (▲, ▼,
, ), SELECT and EXIT
47
USING COMMERCIAL SKIP
The URC-8910 remote control includes a unique Commercial Skip
feature, once programmed, that will allow you to skip viewing commercials by pressing the COM SKIP key. Then, as you change channels (to view another program without commercials), an internal
timer will count down a preset time interval before returning the
device to the original channel.
Programming Commercial Skip
For example, let’s assume you are watching a national sports event
on channel 2 that consistently breaks for one-minute commercials.
Meanwhile, cable channel 26 is showing a favorite action movie
without commercials. By performing the following steps, you can set
Commercial Skip to automatically return the cable converter to the
sports event after one minute of viewing the movie:
NOTE: Commercial Skip only works in the following modes: TV, VCR, DVD,
CBL, and SAT.
1.
Select the device where channels will be changed
(e.g., CBL).
2.
On the URC-8910 remote control, press and hold
COM SKIP until you see the display change from the
current device and time to [CHANNEL].
NOTE: The device, its code, and time are examples. Your
remote control settings may be different.
NOTE: To exit programming at any time, press EXIT once or
allow 30 seconds of inactivity to lapse. You will see [EXIT
SETUP] as the remote control returns to normal operation.
NOTE: [INVALID] means you have inadvertently pressed an
incorrect key. Note your error and continue programming.
3.
Use the keypad to enter a favorite channel number
(e.g., 002). The display will show your entry.
NOTE: If the original remote control required pressing an
Enter key to change the channel, also press the ENTER key
after the channel number (e.g., 0 -0 -2-ENTER). However, the
display will not show the ENTER key.
NOTE: If you made a mistake during entry, press EXIT once.
You will see [EXIT SETUP] as the remote control returns to
normal operation. Then try programming Commercial Skip
again starting with step 1.
4.
SELECT
Press SELECT once to accept your channel entry.You
will see the display change to [30 SEC].
48
5.
or
6.
SELECT
If desired, press ▲ (or ▼) one or times to select a
different time interval.Your choices are 30 (default),
60, 90, 120, 150, or 180 seconds. For this example,
select 60 seconds.
Press SELECT once to accept the 60-second setting.
You will see [SUCCESS] appear in the display,
followed by [EXIT SETUP]. The URC-8910 remote
control will automatically exit the programming
mode and return to normal operation.
Operating Commercial Skip
In our example, let’s assume you are watching a national sports
event on cable channel 2 and it looks like a commercial is about to
appear. Immediately, press COM SKIP once and then enter channel
26 (e.g. 026).
The cable converter will switch to channel 26 and, after 1 minute,
automatically return to channel 2. The next time a commercial
appears, try pressing COM SKIP once, followed by PREV once to
activate the same sequence.
For a more powerful Commercial Skip technique, try programming
these steps into an open macro key (see Using Macros on page 34).
This way you will be able to press one key to switch channels and
return after a preset time.
49
RESTORING FACTORY DEFAULT SETTINGS
The URC-8910 remote control includes an Operation Reset program
that you can use to restore the unit to factory default settings.
IMPORTANT: Executing this program will erase all custom settings,
including Home Theater assignments, Macros, Learned Keys, Keymoved
Keys, and all device assignments.
1.
On the URC-8910 remote control, press and hold
SET until you see the display change from the current device and time to [CODE SET].
NOTE: The device, its code, and time are examples. Your
remote control settings may be different.
NOTE: To exit programming at any time, press EXIT once or
allow 30 seconds of inactivity to lapse. You will see [EXIT
SETUP] as the remote control returns to normal operation.
NOTE: [INVALID] means you have inadvertently pressed an
incorrect key. Note your error and continue programming.
2.
Press the ▲ key twice until you see the display
change to [OPS RESET].
(x 2)
NOTE: If you go past [OPS RESET] , press the ▼ key one or
more times to return to it.
3.
SELECT
4.
SELECT
Press SELECT once to begin programming.You will
see the display change to [CLR SETUP].
Press SELECT once to start the process.You will see
the display change to [RESET RAM] as the active
memory is cleared, followed by [RESET E2] as the
preprogrammed memory is restored.
Then you will see [EXIT SETUP] as the URC-8910
remote control automatically exits the programming
mode and returns to normal operation.
50
ABOUT UPGRADING
The URC-8910 remote control has the largest infrared code library
available. However, if you purchase a brand new home entertainment or home automation device, it may not respond to the codes
stored in the remote control’s memory.
If this happens, please contact our Customer Support department
(see Troubleshooting Section on page 52) to upgrade the URC-8910
remote control. The Customer Support representative will search our
entire database for a code that matches your device and instruct you
how to enter it into your URC-8910 remote control.
If the code for your home entertainment or home automation device
is not in our database, we will need to “capture” the code for that
device from its original remote control.A new code would then be
created and entered into your URC-8910 remote control. If necessary,
the Customer Support representative can instruct you how to begin
the capture procedure.
NOTE: One For All reserves the right to replace a returned remote control with
a new one of equal or superior functionality.
Upgrade Exclusions
• Home entertainment or home automation devices controlled by
radio frequency (RF/UHF), wired, or ultrasonic remote controls.
Only devices controlled by infrared remote controls are covered.
• Home entertainment or home automation devices not controlled
by remote controls.
• Broken or defective product.
• Products that operate over 100 kHz.
• Infrared keyboards and infrared pointing devices (such as
mouse substitutes).
• All products for sale and/or use outside the continental United
States, Hawaii,Alaska, or Canada.
SPECIFICATIONS
Remote Control Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 AAA
Batteries
Remote Control Dimensions
(H x W x D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2⁄16 x 2-10⁄16 x 2-3⁄16
in.
(H x W x D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 232 x 65 x 31
mm
Remote Control Weight (without Batteries) . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 oz (220
g)
NOTE: Specifications are typical. Individual units might vary. Specifications
are subject to change and improvement without notice.
51
TROUBLESHOOTING
PROBLEM:
LCD (Liquid Crystal Display) begins to fade, does not
appear, or the LOW BATTERY (
)icon appears.
SOLUTION:
Replace the batteries with four (4) new AAA alkaline
batteries (see page 4).
PROBLEM:
LED (red light) and IR ( ) icon blinks when you press a
key, but home entertainment device does not respond.
SOLUTION:
Be sure to select the correct device key for the device you
want to control.Also, aim the URC-8910 remote control
at the device not farther than 15 feet away.
PROBLEM:
The URC-8910 remote control does not control home
entertainment devices or commands do not work properly.
SOLUTION:
Try all listed codes for the device brands being set up.
Make sure they originally can be operated with an
infrared remote control.
PROBLEM:
TV/VCR combo does not respond properly.
SOLUTION:
Use the VCR codes for your brand. Some combo units may
require both a TV code and a VCR code for full operation.
PROBLEM:
The URC-8910 remote control does not turn on Sony or
Sharp TV/VCR Combo.
SOLUTION:
For Power On, these products require programming TV
codes. For Sony, use TV code 0000 and VCR code 0032.
For Sharp, use TV code 0093 and VCR code 0048.
PROBLEM:
Changing channels does not work properly.
SOLUTION:
If original remote control required pressing ENTER to
change channels, press ENTER on the URC-8910 remote
control after entering the channel number.
PROBLEM:
During learning, the display shows an [ERROR] message
after pressing and holding a key to be learned.
SOLUTION:
A bad capture has occurred.Avoid high-ambient light
sources, such as direct daylight and fluorescent bulbs.
Also, try readjusting positions of remote controls before
performing the procedure again. Make sure the key(s)
on the original remote control is (are) operating correctly.
PROBLEM:
CH+ and CH- do not work for your RCA TV.
SOLUTION:
Due to RCA design (1983-1987), only the original remote
control will operate these functions.
PROBLEM:
No remote control of volume.
SOLUTION:
See Using Volume Lock on page 32 to lock/unlock the
volume controls.
PROBLEM:
The URC-8910 remote control turns on audio devices and
controls volume, but does not change preset channels.
SOLUTION:
Some products may need both a Tuner/Receiver code
and an Audio Amplifier code for remote control of all
features on your audio device.
PROBLEM:
Tried Search For Your Code method and still could not find
a working code.
SOLUTION:
Your device may be newer than the URC-8910 remote
control. (See About Upgrading on page 51.)
52
PROBLEM:
Your satellite (DSS) receiver does not respond to the codes
listed on page 22.
SOLUTION:
Make sure the satellite (DSS) receiver can be operated
with an Infrared (IR) remote control and is not set up to
receive only Radio Frequency (RF) signals.
SOLUTION:
Please contact us in any of the following ways:
• Please visit : www.oneforall.com
• If the above website is not able to provide you with the
information you need, please email us at
[email protected]
• Customer Support : (330) 405-8616
ERROR MESSAGES
A wrong key sequence or incorrect data has
been entered. Try entry again.
Requested manufacturer’s code has not been
found in the remote control’s database. Try
another code.
Macro sequence being entered has reached the
maximum limit of 15 keystrokes. Try entry
again with fewer keystrokes.
A complete cycle of code search in the
URC-8910 remote control’s database has been
reached. Try another code search or contact
Customer Support (see Troubleshooting Section
on page 52).
An error has occurred during a learning or
programming sequence. Try entry again.
Indicates a check result of E2 status is either
bad or is not present. Contact Customer
Support (see Troubleshooting Section
on page 52).
Indicates data captured during learning has
filled the URC-8910 remote control’s memory.
Try deleting older learned keys to free up
memory space (see page 31).
Indicates data captured during learning has
caused a error in the URC-8910 remote control’s memory. Try learning again.
53
KEY INDEX
Audio Amplifier Functions
Press RCVR/AMP once to control your audio
amplifier.
Press POWER once to turn on or off the
selected device (e.g, RCVR/AMP).
Use GUIDE to display your audio amplifier’s
program guide or setup menu.
Use INFO to display the audio amplifier’s
program information.
▲
SELECT
Use SELECT to set the surround sound. Use ▲
(or ▼) to adjust the volume higher (or lower).
Use (or ) to adjust the balance left (or
right).
▲
D
RROUN SOUND
SU
Use VOL+ (or VOL-) to raise (or lower) the
audio amplifier’s audio volume.
Press MUTE once to turn the audio amplifier’s
audio off or on.
Use CH+ (or CH-) to select the audio amplifier’s
next higher (or lower) station (if applicable).
Use PREV to change the radio band
(if applicable).
Use the keypad (1 ~ 9 and 0) to
select audio sources (e.g., 1~ 10). If
the original remote control required
pressing an Enter key to change the
audio source, also press the ENTER
key after the source number (e.g.,
9 -ENTER).
Press ENTER once after entering the source
numbers on some audio amplifiers.
Use TV/VID to switch the audio amplifier
between input and output.
54
Use the transport keys to control
your CD player (if applicable).
Use SLEEP to activate your audio amplifer’s
sleep timer (not available for all devices).
After programming, press M1 ~ M3 once to
run a desired macro (see Using Macros on
page 34).
After programming, press L1 ~ L4
once to activate a learned function.
(See Using Learning on page 29.)
Use to turn on or off the key backlight.
When this feature is activated, keys will
remain backlit for 5 seconds after the last key
press. In the setup mode, backlighting
will remain on for 30 seconds.
Use SET for all programming sequences.
Audio Cassette Deck Functions
Press AUX once to control your audio cassette
deck. (See Re-assigning Device Keys on page
37.)
Press POWER once to turn on or off the
selected device (e.g, AUX).
Use GUIDE to display your audio cassette
deck’s program guide (if applicable).
D
RROUN SOUND
SU
SELECT
▲
▲
Use INFO to display the audio cassette deck’s
program information.
Use the cursor keys (▲ , ▼, or ) to move
the cursor in the audio cassette deck’s program guide and menu screens. Use SELECT to
choose options from the menu or guide.
Use VOL+ (or VOL-) to raise (or lower) the
audio cassette deck’s audio volume
(if applicable).
continued on next page...
55
KEY INDEX
Audio Cassette Deck Functions (continued)
Press MUTE once to turn the audio cassette
deck’s audio off or on (if applicable).
Use the keypad (1 ~ 9 and 0) to
directly select tracks. If the original
remote control required pressing an
Enter key to select a track, also press
the ENTER key after the track number
(e.g., 1-2 -ENTER).
Use TV/VID to switch the audio cassette deck
between input and output.
Use the transport keys to control
your audio cassette deck.
After programming, press M1 ~ M3 once to
run a desired macro (see Using Macros on
page 34).
After programming, press L1 ~ L4
once to activate a learned function.
(See Using Learning on page 29.)
Use to turn on or off the key backlight.
When this feature is activated, keys will
remain backlit for 5 seconds after the last key
press. In the setup mode, backlighting
will remain on for 30 seconds.
Use SET for all programming sequences.
56
Audio Receiver Functions
Press RCVR/AMP once to control your audio
receiver.
Press POWER once to turn on or off the
selected device (e.g, RCVR/AMP).
Use GUIDE to display your audio receiver’s
program guide or setup menu.
Use INFO to display the audio receiver’s
program information.
▲
SELECT
Use SELECT to set the surround sound. Use ▲
(or ▼) to adjust the volume higher (or lower).
Use (or ) to adjust the balance left (or
right).
▲
D
RROUN SOUND
SU
Use VOL+ (or VOL-) to raise (or lower) the
audio receiver’s audio volume.
Press MUTE once to turn the audio receiver’s
audio off or on.
Use CH+ (or CH-) to select the audio receiver’s
next higher (or lower) station (if applicable).
Use PREV to change the radio band
(if applicable).
Use the keypad (1 ~ 9 and 0) to
select audio sources (e.g., 1~ 10). If
the original remote control required
pressing an Enter key to change the
audio source, also press the ENTER
key after the source number (e.g.,
9 -ENTER).
Press ENTER once after entering the source
numbers on some audio receivers.
Use TV/VID to switch the audio receiver
between input and output.
continued on next page...
57
KEY INDEX
Audio Receiver Functions (continued)
Use the transport keys to control
your CD player (if applicable).
Use SLEEP to activate your audio receiver’s
sleep timer (not available for all devices).
After programming, press M1 ~ M3 once to
run a desired macro (see Using Macros on
page 34).
After programming, press L1 ~ L4
once to activate a learned function.
(See Using Learning on page 29.)
Use to turn on or off the key backlight.
When this feature is activated, keys will
remain backlit for 5 seconds after the last key
press. In the setup mode, backlighting
will remain on for 30 seconds.
Use SET for all programming sequences.
Audio Turntable Functions
Press AUX once to control your audio turntable. See Re-assigning Device Keys on page 37.
Press POWER once to turn on or off the
selected device (e.g, AUX).
Use GUIDE to display your audio turntable’s
program guide (if applicable).
Use INFO to display the audio turntable’s
program information.
SELECT
58
▲
Use SELECT to select a disc. Use ▲ (or ▼) to
select the next (or previous) LP. Use (or )
to select the next (or previous) track.
▲
D
RROUN SOUND
SU
Use VOL+ (or VOL-) to raise (or lower) the
audio turntable’s audio volume (if applicable).
Press MUTE once to turn the audio turntable’s
audio off or on (if applicable).
Use the keypad (1 ~ 9 and 0) to
directly select tracks. If the original
remote control required pressing an
Enter key to select a track, also press
the ENTER key after the track number
(e.g., 1-2 -ENTER).
Use the transport keys to control
your audio turntable (if applicable).
After programming, press M1 ~ M3 once to
run a desired macro (see Using Macros on
page 34).
After programming, press L1 ~ L4
once to activate a learned function.
(See Using Learning on page 29.)
Use to turn on or off the key backlight.
When this feature is activated, keys will
remain backlit for 5 seconds after the last key
press. In the setup mode, backlighting
will remain on for 30 seconds.
Use SET for all programming sequences.
59
KEY INDEX (Continued)
Cable Converter Functions
Press CBL once to control your cable
converter.
Press POWER once to turn on or off the
selected device (e.g, SAT).
Press MENU once to display your cable
converter’s main menu.
Use GUIDE to display your cable converter’s
program guide or setup menu.
Use EXIT to exit from your cable converter’s
guide or menu.
D
RROUN SOUND
SU
SELECT
▲
▲
Use INFO to display the cable converter’s
current channel and program information.
Use the cursor keys (▲ , ▼, , or ) to move
the cursor in the cable converter’s program
guide and menu screens. Use SELECT to
choose options from the menu or guide.
Use VOL+ (or VOL-) to raise (or lower) the
cable converter’s audio volume (if applicable).
Press MUTE once to turn the cable converter’s
audio off or on (if applicable).
Use FAV to scan favorite channels and/or all
channels.(See Using Channel Scan and
Programming Favorite Channel Scan on page
41.)
Use CH+ (or CH-) to select the cable converter’s next higher (or lower) channel.
Press PREV once to recall the last-viewed
channel and to page back one screen on the
cable converter’s main menu.
Use the keypad (1 ~ 9 and 0) to
directly select channels (e.g., 009 or
031). If the original remote control
required pressing an Enter key to
change the channel, also press the
ENTER key after the channel number
(e.g., 0-3-1-ENTER).
60
Press ENTER once after entering the channel
numbers on some TVs.
Use TV/VID to switch the TV’s input to view
TV or cable programs.
Use the transport keys to control
your cable converter’s VOD service
(if applicable).
Use SLEEP to activate your cable converter’s
sleep timer (not available for all devices).
After programming, press M1 ~ M3 once to
run a desired macro (see Using Macros on
page 34).
After programming, press L1 ~ L4
once to activate a learned function.
(See Using Learning on page 29.)
Use PIP to switch the Picture-In-Picture
feature on or off (if available on your TV).
Use MOVE to move the window picture
to different positions in the main picture.
Use SWAP to switch images and sound
between the main and window pictures.
After programming, use COM SKIP to skip
commercials on your cable converter. (See
Using Commercial Skip on page 48.)
Use to turn on or off the key backlight.
When this feature is activated, keys will
remain backlit for 5 seconds after the last key
press. In the setup mode, backlighting
will remain on for 30 seconds.
Use SET for all programming sequences.
61
KEY INDEX (continued)
CD Player Functions
Press CD once to control your CD player.
Press POWER once to turn on or off the
selected device (e.g, CD).
Use GUIDE to display your CD player’s
program guide.
Use INFO to display the CD player’s current
channel and program information.
▲
SELECT
Use SELECT to select a compact disc. Use ▲
(or ▼) to select the next (or previous) CD.
Use (or ) to select the next (or previous)
track.
▲
D
RROUN SOUND
SU
Use VOL+ (or VOL-) to raise (or lower) the
CD player’s audio volume (if applicable).
Press MUTE once to turn the CD player’s
audio off or on (if applicable).
Use the keypad (1 ~ 9 and 0) to
directly select tracks. If the original
remote control required pressing an
Enter key to select a track, also press
the ENTER key after the track number
(e.g., 1-2 -ENTER).
Use the transport keys to control
your CD player.
After programming, press M1 ~ M3 once to
run a desired macro (see Using Macros on
page 34).
After programming, press L1 ~ L4
once to activate a learned function.
(See Using Learning on page 29.)
62
Use to turn on or off the key backlight.
When this feature is activated, keys will
remain backlit for 5 seconds after the last key
press. In the setup mode, backlighting
will remain on for 30 seconds.
Use SET for all programming sequences.
DVD Player Functions
Press DVD once to control your DVD player.
Press POWER once to turn on or off the
selected device (e.g, DVD).
Press MENU once to display your DVD player’s
main menu.
Use GUIDE to display your DVD player’s
program guide.
Use EXIT to exit from your DVD player’s guide
or menu.
D
RROUN SOUND
SU
SELECT
▲
▲
Use INFO to display the DVD player’s current
channel and program information.
Use the cursor keys (▲ , ▼, or ) to move
the cursor in the DVD player’s program guide
and menu screens. Use SELECT to choose
options from the menu or guide.
Use VOL+ (or VOL-) to raise (or lower) the
DVD player’s audio volume (if applicable).
Press MUTE once to turn the DVD player’s
audio off or on (if applicable).
Use FAV to scan favorite channels and/or all
channels.(See Using Channel Scan and
Programming Favorite Channel Scan on page
41.)
Use the keypad (1 ~ 9 and 0) to
directly select chapters (e.g., 09 or
31). If the original remote control
required pressing an Enter key to
select a chapter, also press the ENTER
key after the chapter number
(e.g., 3-1-ENTER).
continued on next page...
63
KEY INDEX
DVD Player Functions (continued)
Use TV/VID to switch the TV’s input to view
TV or DVD programs.
Use the transport keys to control
your DVD player.
After programming, press M1 ~ M3 once to
run a desired macro (see Using Macros on
page 34).
After programming, press L1 ~ L4
once to activate a learned function.
(See Using Learning on page 29.)
Use to turn on or off the key backlight.
When this feature is activated, keys will
remain backlit for 5 seconds after the last key
press. In the setup mode, backlighting
will remain on for 30 seconds.
Use SET for all programming sequences.
64
Home Automation Functions
Press AUX once to control home automation.
(See Re-assigning Device Keys on page 37.)
Press POWER once to turn on home
automation.
Use VOL+ (or VOL-) to brighten (or dim) the
lights controlled by home automation.
Press MUTE once to turn off home
automation.
Use CH+ (or CH-) to turn home automation
on (or off).
After programming, press M1 ~ M3 once to
run a desired macro (see Using Macros on
page 34).
After programming, press L1 ~ L4
once to activate a learned function.
(See Using Learning on page 29.)
Use to turn on or off the key backlight.
When this feature is activated, keys will
remain backlit for 5 seconds after the last key
press. In the setup mode, backlighting
will remain on for 30 seconds.
Use SET for all programming sequences.
65
KEY INDEX
LD (Laser Disc) Player Functions
Press AUX once to control home automation.
(See Re-assigning Device Keys on page 37.)
Press POWER once to turn on or off the
selected device (e.g, AUX).
Press MENU once to display your LD player’s
main menu.
Use GUIDE to display your LD player’s
program guide.
Use EXIT to exit from your LD player’s guide
or menu.
D
RROUN SOUND
SU
SELECT
▲
▲
Use INFO to display the LD player’s current
channel and program information.
Use the cursor keys (▲ , ▼, or ) to move
the cursor in the LD player’s program guide
and menu screens. Use SELECT to choose
options from the menu or guide.
Use VOL+ (or VOL-) to raise (or lower) the
LD player’s audio volume (if applicable).
Press MUTE once to turn the LD player’s
audio off or on (if applicable).
Use the keypad (1 ~ 9 and 0) to
directly select chapters (e.g., 09 or
31). If the original remote control
required pressing an Enter key to
select a chapter, also press the ENTER
key after the chapter number
(e.g., 3-1-ENTER).
Use TV/VID to switch the TV’s input to view
TV or LD programs.
Use the transport keys to control
your LD player.
66
After programming, press M1 ~ M3 once to
run a desired macro (see Using Macros on
page 34).
After programming, press L1 ~ L4
once to activate a learned function.
(See Using Learning on page 29.)
Use to turn on or off the key backlight.
When this feature is activated, keys will
remain backlit for 5 seconds after the last key
press. In the setup mode, backlighting
will remain on for 30 seconds.
Use SET for all programming sequences.
Satellite Receiver Functions
Press SAT once to control your satellite
receiver.
Press POWER once to turn on or off the
selected device (e.g, SAT).
Press MENU once to display your satellite
receiver’s main menu.
Use GUIDE to display your satellite receiver’s
program guide or setup menu.
Use EXIT to exit from your satellite receiver’s
guide or menu.
D
RROUN SOUND
SU
SELECT
▲
▲
Use INFO to display the satellite receiver’s
current channel and program information.
Use the cursor keys (▲ , ▼, or ) to move
the cursor in the satellite receiver’s program
guide and menu screens. Use SELECT to
choose options from the menu or guide.
Use VOL+ (or VOL-) to raise (or lower) the
satellite receiver’s audio volume (if applicable).
Press MUTE once to turn the satellite receiver’s
audio off or on (if applicable).
Use FAV to scan favorite channels and/or all
channels.(See Using Channel Scan and Programming Favorite Channel Scan on page 41.)
continued on next page...
67
KEY INDEX
Satellite Receiver Functions (continued)
Use CH+ (or CH-) to select the satellite
receiver’s next higher (or lower) channel.
Press PREV once to recall the last-viewed
channel and to page back one screen on the
satellite receiver’s main menu.
Use the keypad (1 ~ 9 and 0) to
directly select channels (e.g., 009 or
031). If the original remote control
required pressing an Enter key to
change the channel, also press the
ENTER key after the channel number
(e.g., 0-3-1-ENTER).
Press ENTER once after entering the channel
numbers on some TVs.
Use TV/VID to switch the TV’s input to view
TV or satellite programs.
Use the transport keys to control
your satellite receiver’s PVR or VOD
service (if applicable).
Use SLEEP to activate your satellite receiver’s
sleep timer (not available for all devices).
After programming, press M1 ~ M3 once to
run a desired macro (see Using Macros on
page 34).
After programming, press L1 ~ L4
once to activate a learned function.
(See Using Learning on page 29.)
Use PIP to switch the Picture-In-Picture
feature on or off (if available on your TV).
Use MOVE to move the window picture
to different positions in the main picture.
Use SWAP to switch images and sound
between the main and window pictures.
68
After programming, use COM SKIP to skip
commercials on your satellite receiver. (See
Using Commercial Skip on page 48.)
Use to turn on or off the key backlight.
When this feature is activated, keys will
remain backlit for 5 seconds after the last key
press. In the setup mode, backlighting
will remain on for 30 seconds.
Use SET for all programming sequences.
TV Functions
Press TV once to control your television.
Press POWER once to turn on or off the
selected device (e.g, TV).
Press MENU once to display your TV’s
main menu.
Use GUIDE to display your TV’s program
guide or setup menu.
Use EXIT to exit from your TV’s guide
or menu.
D
RROUN SOUND
SU
SELECT
▲
▲
Use INFO to display the TV’s current channel
and program information.
Use the cursor keys (▲ , ▼, or ) to move
the cursor in the TV’s program guide and
menu screens. Use SELECT to choose options
from the menu or guide.
Use VOL+ (or VOL-) to raise (or lower) the
TV’s audio volume.
Press MUTE once to turn the TV audio off
or on.
Use FAV to scan favorite channels and/or all
channels.(See Using Channel Scan and
Programming Favorite Channel Scan on page
41.)
continued on next page...
69
KEY INDEX
TV Functions (continued)
Use CH+ (or CH-) to select the TV’s next
higher (or lower) channel.
Press PREV once to recall the last-viewed
channel and to page back one screen on the
TV’s main menu.
Use the keypad (1 ~ 9 and 0) to
directly select channels (e.g., 009 or
031). If the original remote control
required pressing an Enter key to
change the channel, also press the
ENTER key after the channel number
(e.g., 0-3-1-ENTER).
Press ENTER once after entering the channel
numbers on some TVs.
Use TV/VID to switch the TV’s input to view
TV or video programs.
Use the transport keys to control
your VCR.
To record a VCR program, press REC
twice.
Use SLEEP to activate your TV’s sleep
timer (not available for all devices).
After programming, press M1 ~ M3 once to
run a desired macro (see Using Macros on
page 34).
After programming, press L1 ~ L4
once to activate a learned function.
(See Using Learning on page 29.)
Use PIP to switch the Picture-In-Picture
feature on or off (if available on your TV).
Use MOVE to move the window picture
to different positions in the main picture.
Use SWAP to switch images and sound
between the main and window pictures.
70
After programming, use COM SKIP to skip
commercials on your TV. (See Using
Commercial Skip on page 48.)
Use to turn on or off the key backlight.
When this feature is activated, keys will
remain backlit for 5 seconds after the last key
press. In the setup mode, backlighting
will remain on for 30 seconds.
Use SET for all programming sequences.
VCR Functions
Press VCR once to control your VCR.
Press POWER once to turn on or off the
selected device (e.g, VCR).
Press MENU once to display your VCR’s
main menu.
Use GUIDE to display your VCR/PVR’s
program guide or setup menu (if applicable).
D
RROUN SOUND
SU
SELECT
▲
▲
Use EXIT to exit from your VCR’s guide
or menu.
Use the cursor keys (▲ , ▼, or ) to move
the cursor in the VCR’s program guide and
menu screens. Use SELECT to choose options
from the menu or guide.
Use VOL+ (or VOL-) to raise (or lower) the
VCR’s audio volume (if applicable).
Press MUTE once to turn the VCR audio off
or on (if applicable).
Use FAV to scan favorite channels and/or all
channels.(See Using Channel Scan and
Programming Favorite Channel Scan on page
41.)
Use CH+ (or CH-) to select the TV’s next
higher (or lower) channel.
continued on next page...
71
KEY INDEX
VCR Functions (continued)
Press PREV once to recall the last-viewed
channel and to page back one screen on the
VCR’s main menu.
Use the keypad (1 ~ 9 and 0) to
directly select channels (e.g., 009 or
031). If the original remote control
required pressing an Enter key to
change the channel, also press the
ENTER key after the channel number
(e.g., 0-3-1-ENTER).
Press ENTER once after entering the channel
numbers on some VCRs.
Use TV/VID to switch the TV’s input to view
TV or VCR programs.
Use the transport keys to control
your VCR.
To record a VCR program, press REC
twice.
Use SLEEP to activate your VCR’s sleep
timer (not available for all devices).
After programming, press M1 ~ M3 once to
run a desired macro (see Using Macros on
page 34).
After programming, press L1 ~ L4
once to activate a learned function.
(See Using Learning on page 29.)
Use PIP to switch the Picture-In-Picture
feature on or off (if available on your TV).
Use MOVE to move the window picture
to different positions in the main picture.
Use SWAP to switch images and sound
between the main and window pictures.
72
Use to turn on or off the key backlight.
When this feature is activated, keys will
remain backlit for 5 seconds after the last key
press. In the setup mode, backlighting
will remain on for 30 seconds.
Use SET for all programming sequences.
LIMITED WARRANTY
One For All® warrants, to the original purchaser only, that this product will
be free from defects in materials and workmanship, under normal use, for
ninety (90) days from the date of original purchase.
This limited warranty is valid only on ONE FOR ALL® product purchased
and used in the United States of America or Canada, and does not apply to
products used for industrial or commercial purpose.
The limited warranty does not cover damage or failure caused by products
or services not supplied by ONE FOR ALL® , or which result from accident,
misuse, abuse, neglect, mishandling, misapplication, faulty installation, setup adjustment, improper maintenance, alteration, maladjustment of consumer controls, modifications, commercial use, or that is attributable to acts
of God.
There are no express warranties except as listed above. ONE FOR ALL®
SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT OR ARISING OUT
OF ANY BREACH OF WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE,ARE LIMITED TO THE WARRANTY PERIOD SET FORTH ABOVE. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on
how long an implied warranty lasts, so the above exclusions or limitations
may not apply to you. This warranty gives you specific legal rights and you
may also have other rights which vary from state to state.
To obtain warranty service for a defective product during the warranty period, please return the product, preferably in the original carton, along with
your purchase receipt, to the store of original purchase.A note detailing the
complaint would be helpful. The store, at its option, will replace or repair
this product if found to be defective.
One For All: 330-405-8655 (for Warranty only)
73
ADDITIONAL INFORMATION
As you update your home entertainment system, One For All® has
a universal remote control that will fit your needs. Look for these
exciting products at a retailer near you.
One For All 3 Device (BIG KEYS) . . . . . . . . . . . . . . . . . . . . URC-3300
One For All Access 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-3605
One For All Video Expert 4 Device . . . . . . . . . . . . . . . . . . . URC-4081
One For All Video Expert Plus 4L
Upgradeable Remote Control with Learning . . . . . . . . . . URC-4880
One For All 4 Device (BIG KEYS) . . . . . . . . . . . . . . . . . . . . URC-4330
One For All Access 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-4605
One For All Access 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . URC-5705
One For All 6 Home Theater. . . . . . . . . . . . . . . . . . . . . . . . . URC-6011
One For All 8 Home Theater. . . . . . . . . . . . . . . . . . . . . . . . . URC-8011
One For All 8L Home Theater with Learning . . . . . . . . . . URC-8811
One For All A/V Producer 8 Device Learner . . . . . . . . . . . URC-8910
One For All IR/RF Home Producer 8 Device Learner . . . URC-9910
ONE FOR ALL® is the registered trademark of Universal Electronics
Inc. Computime International Ltd. is the Licensee of the ONE FOR
ALL® brand for USA and Canada.
Copyright 2002 by Universal Electronics Inc. No part of this publication may be reproduced, transmitted, transcribed, stored in any
retrieval system, or translated to any language, in any form or by any
means,electronic,mechanical,magnetic,optical,manual,or otherwise,
without the prior written permission of Universal Electronics Inc.
The One For All A/V LCD 8-Device With Learning Universal Remote
Control (URC-8910) is compatible for use in North America,
excluding Mexico.
URC-8910B00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 06/03
74
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement