Sony DVP-NS77H User Guide Manual - DVDPlayer

Sony DVP-NS77H User Guide Manual - DVDPlayer
3-209-001-11(1)
CD/DVD
Player
Operating Instructions
Operating Instructions
US
Manual de instrucciones
ES
DVP-NS77H
© 2007 Sony
Corporation
Downloaded From DvDPlayer-Manual.com Sherwood
Manuals
WARNING
To reduce the risk of fire or
electric shock, do not expose
this apparatus to rain or
moisture.
To avoid electrical shock, do
not open the cabinet. Refer
servicing to qualified
personnel only.
For customers in the U.S.A
Owner’s Record
The model and serial numbers are
located at the rear of the unit.
Record the serial number in the
space provided below. Refer to
them whenever you call upon your
Sony dealer regarding this product.
The AC power cord must be
changed only at a qualified
service shop.
Model No. DVP-NS77H
Serial No.______________
Do not expose the battery to
excessive heat such as direct
sunlight, fire, or the like.
CAUTION
The use of optical instruments with
this product will increase eye
hazard. As the laser beam used in
this CD/DVD player is harmful to
eyes, do not attempt to disassemble
the cabinet.
Refer servicing to qualified
personnel only.
This symbol is
intended to alert the
user to the presence
of uninsulated
“dangerous voltage”
within the product’s enclosure that
may be of sufficient magnitude to
constitute a risk of electric shock to
persons.
This symbol is
intended to alert the
user to the presence
of important
operating and
maintenance (servicing)
instructions in the literature
accompanying the appliance.
• To keep the disc clean, handle
the disc by its edge. Do not touch
the surface. Dust, fingerprints, or
scratches on the disc may cause
it to malfunction.
Note
This equipment has been tested
and found to comply with the
limits for a Class B digital device,
pursuant to Part 15 of the FCC
Rules. These limits are designed to
provide reasonable protection
against harmful interference in a
residential installation. This
equipment generates, uses, and can
radiate radio frequency energy
and, if not installed and used in
accordance with the instructions,
may cause harmful interference to
radio communications. However,
there is no guarantee that
interference will not occur in a
particular installation. If this
equipment does cause harmful
interference to radio or television
reception, which can be
determined by turning the
equipment off and on, the user is
encouraged to try to correct the
interference by one or more of the
following measures:
– Reorient or relocate the
receiving antenna.
– Increase the separation
between the equipment and
receiver.
– Connect the equipment into an
outlet on a circuit different
from that to which the receiver
is connected.
– Consult the dealer or an
experienced radio/TV
technician for help.
CAUTION
You are cautioned that any
changes or modifications not
expressly approved in this manual
could void your authority to
operate this equipment.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
2
Notes About the
Discs
• Do not expose the disc to direct
sunlight or heat sources such as
hot air ducts, or leave it in a car
parked in direct sunlight as the
temperature may rise
considerably inside the car.
• After playing, store the disc in its
case.
• Clean the disc with a cleaning
cloth. Wipe the disc from the
center out.
• Do not use solvents such as
benzine, thinner, commercially
available cleaners, or anti-static
spray intended for vinyl LPs.
• If you have printed the disc’s
label, dry the label before
playing.
Important
Safeguards
For your protection, please read these safety
instructions completely before operating the appliance,
and keep this manual for future reference.
Carefully observe all warnings, precautions and
instructions on the appliance, or the one described in
the operating instructions and adhere to them.
Use
Power sources
This set should be operated only
from the type of power source
indicated on the marking label. If
you are not sure of the type of
electrical power supplied to your
home, consult your dealer or local power company.
For those sets designed to operate from battery power,
or other sources, refer to the operating instructions.
Grounding or Polarization
This set is equipped with a polarized ac power cord
plug (a plug having one blade wider than the other), or
with a three-wire grounding type plug (a plug having a
third pin for grounding). Follow the instructions
below:
For the set with a polarized AC power
cord plug:
This plug will fit into the power
outlet only one way. This is a
safety feature. If you are unable to
insert the plug fully into the outlet, try reversing the
plug. If the plug should still fail to fit, contact your
electrician to have a suitable outlet installed. Do not
defeat the safety purpose of the polarized plug by
forcing it in.
For the set with a three-wire grounding
type AC plug:
This plug will only fit into a
grounding-type power outlet. This
is a safety feature. If you are
unable to insert the plug into the
outlet, contact your electrician to have a suitable outlet
installed. Do not defeat the safety purpose of the
grounding plug.
Overloading
Do not overload wall outlets,
extension cords or convenience
receptacles beyond their capacity,
since this can result in fire or
electric shock.
Object and Liquid Entry
Never push objects of any kind into
the set through openings as they
may touch dangerous voltage points
or short out parts that could result in
a fire or electric shock. Never spill
liquid of any kind on the set.
Attachments
Do not use attachments not
recommended by the manufacturer, as
they may cause hazards.
Cleaning
Unplug the set from the wall outlet
before cleaning or polishing it. Do
not use liquid cleaners or aerosol
cleaners. Use a cloth lightly
dampened with water for cleaning
the exterior of the set.
Installation
Water and Moisture
Do not use power-line operated sets
near water - for example, near a
bathtub, washbowl, kitchen sink, or
laundry tub, in a wet basement, or
near a swimming pool, etc.
Power-Cord Protection
Route the power cord so that it is
not likely to be walked on or
pinched by items placed upon or
against them, paying particular
attention to the plugs, receptacles, and the point where
the cord exits from the appliance.
US
Accessories
Do not place the set on an
unstable cart, stand, tripod,
bracket, or table. The set may
fall, causing serious injury to a
child or an adult, and serious damage to the set. Use
only a cart stand tripod, bracket, or table recommended
by the manufacturer.
An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance
and cart combination to overturn.
S3125A
Ventilation
The slots and openings in the cabinet are provided for
necessary ventilation. To ensure reliable operation of
the set, and to protect it from overheating, these slots
and openings must never be blocked or covered.
• Never cover the slots and
openings with a cloth or
other materials.
• Never block the slots and
openings by placing the set
on a bed, sofa, rug or other
similar surface.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
3US
• Never place the set in a
confined space, such as a
bookcase, or built-in
cabinet, unless proper
ventilation is provided.
• Do not place the set near or
over a radiator or heat
register, or where it is
exposed to direct sunlight.
Service
Damage Requiring Service
Unplug the set from the wall outlet and refer servicing
to qualified service personnel under the following
conditions:
• When the power cord or plug is
damaged or frayed.
Antennas
Outdoor antenna grounding
If an outdoor antenna or cable system is installed,
follow the precautions below.
An outdoor antenna system should not be located in the
vicinity of overhead power lines or other electric light
or power circuits, or where it can come in contact with
such power lines or circuits.
WHEN INSTALLING AN OUTDOOR ANTENNA
SYSTEM, EXTREME CARE SHOULD BE TAKEN
TO KEEP FROM CONTACTING SUCH POWER
LINES OR CIRCUITS AS CONTACT WITH THEM
IS ALMOST INVARIABLY FATAL.
Be sure the antenna system is grounded so as to provide
some protection against voltage surges and built-up static
charges. Section 810 of the National Electrical Code
provides information with respect to proper grounding of
the mast and supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of grounding
conductors, location of antenna-discharge unit, connection
to grounding electrodes, and requirements for the
grounding electrode.
Antenna Grounding According to the
National Electrical Code
Antenna Lead in Wire
Ground Clamp
Electric Service
Equipment
Antenna Discharge unit
(NEC Section 810-20)
Grounding Conductors
(NEC Section 810-21)
Ground Clamps
Power Service Grounding
Electrode System
(NEC Art 250 Part H)
NEC-NATIONAL ELECTRICAL CODE
Lightning
For added protection for this set during a lightning
storm, or when it is left unattended and unused for long
periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will
prevent damage to the set due to lightning and powerline surges.
• If liquid has been spilled or
objects have fallen into the
set.
• If the set has been exposed
to rain or water.
• If the set has been
subject to excessive
shock by being
dropped, or the cabinet
has been damaged.
• If the set does not operate
normally when following
the operating instructions.
Adjust only those controls
that are specified in the
operating instructions. Improper adjustment
of other controls may result in damage and
will often require extensive work by a
qualified technician to restore the set to normal
operation.
• When the set exhibits a distinct change in
performance - this indicates a need for service.
Servicing
Do not attempt to service the set
yourself as opening or removing
covers may expose you to
dangerous voltage or other
hazards.
Refer all servicing to qualified service personnel.
Replacement parts
When replacement parts are required, be sure the
service technician has used replacement parts specified
by the manufacturer that have the same characteristics
as the original parts.
Unauthorized substitutions may result in fire, electric
shock, or other hazards.
Safety Check
Upon completion of any service or
repairs to the set, ask the service
technician to perform routine
safety checks (as specified by the
manufacturer) to determine that
the set is in safe operating
condition.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
4
On operation
Precautions
• To prevent fire or shock hazard, do not
place objects filled with liquids, such as
vases, on the apparatus.
• Should any solid object or liquid fall into
the cabinet, unplug the player and have it
checked by qualified personnel before
operating it any further.
• If the player is brought directly from a cold
to a warm location, or is placed in a very
damp room, moisture may condense on the
lenses inside the player. Should this occur,
the player may not operate properly. In this
case, remove the disc and leave the player
turned on for about half an hour until the
moisture evaporates.
• When you move the player, take out any
discs. If you don’t, the disc may be
damaged.
On power sources
On adjusting volume
On safety
• The player is not disconnected from the AC
power source as long as it is connected to
the wall outlet, even if the player itself has
been turned off.
• If you are not going to use the player for a
long time, be sure to disconnect the player
from the wall outlet. To disconnect the AC
power cord, grasp the plug itself; never pull
the cord.
On placement
• Place the player in a location with adequate
ventilation to prevent heat build-up in the
player.
• Do not place the player on a soft surface
such as a rug.
• Do not place the player in a location near
heat sources, or in a place subject to direct
sunlight, excessive dust, or mechanical
shock.
• Do not install the player in an inclined
position. It is designed to be operated in a
horizontal position only.
• Keep the player and the discs away from
equipment with strong magnets, such as
microwave ovens, or large loudspeakers.
• Do not place heavy objects on the player.
• Install the player so that the AC power cord
can be unplugged from the wall socket
immediately in the event of trouble.
Do not turn up the volume while listening to
a section with very low level inputs or no
audio signals. If you do, the speakers may be
damaged when a peak level section is played.
On cleaning
Clean the cabinet, panel, and controls with a
soft cloth slightly moistened with a mild
detergent solution. Do not use any type of
abrasive pad, scouring powder or solvent
such as alcohol or benzine.
On cleaning discs, disc/lens cleaners
Do not use cleaning discs or disc/lens
cleaners (including wet or spray types).
These may cause the apparatus to
malfunction.
On replacement of parts
In the event that this unit is repaired, repaired
parts may be collected for reuse or recycling
purposes.
IMPORTANT NOTICE
Caution: This player is capable of holding a
still video image or on-screen display image
on your television screen indefinitely. If
you leave the still video image or on-screen
display image displayed on your TV for an
extended period of time you risk permanent
damage to your television screen. Plasma
display panel televisions and projection
televisions are susceptible to this.
If you have any questions or problems
concerning your player, please consult your
nearest Sony dealer.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
5US
Table of Contents
WARNING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Notes About the Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Important Safeguards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
This Player Can Play the Following Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Guide to Parts and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Guide to the Control Menu Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Hookups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Hooking Up the Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 1: Connecting the Video Cords/HDMI Cords. . . . . . . . . . . . . . . . . . . . .
About the HDMI CONTROL functions for ‘BRAVIA’ Theatre Sync
(for HDMI connections only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 2: Connecting the Audio Cords . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 3: Connecting the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Step 4: Preparing the Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Controlling Your TV with the Supplied Remote . . . . . . . . . . . . . . . . . . . .
Step 5: Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16
17
19
20
22
22
23
24
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Playing Discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Various Play Mode Functions (Program Play, Shuffle Play, Repeat Play,
A-B Repeat Play) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Playback Picture (CUSTOM PICTURE MODE). . . . . . . . . . . .
Sharpening the Picture (SHARPNESS). . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjusting the Delay Between the Picture and Sound (AV SYNC) . . . . . . . . .
Locking Discs (CUSTOM PARENTAL CONTROL,
PARENTAL CONTROL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
26
32
36
37
38
39
Searching for a Scene . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Searching for a Particular Point on a Disc (Scan, Slow-motion Play,
Freeze Frame) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Searching for a Title/Chapter/Track/Scene, etc. . . . . . . . . . . . . . . . . . . . . . . 43
Searching by Scene (PICTURE NAVIGATION) . . . . . . . . . . . . . . . . . . . . . . 44
Sound Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Changing the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
TV Virtual Surround Settings (TVS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Enjoying MP3 Audio and JPEG Images . . . . . . . . . . . . . . . . . . . . . 49
About MP3 Audio Tracks and JPEG Image Files . . . . . . . . . . . . . . . . . . . . . 49
Playing MP3 Audio Tracks or JPEG Image Files. . . . . . . . . . . . . . . . . . . . . . 50
Enjoying JPEG Images as a Slide Show . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
6
Settings and Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Using the Setup Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Display or Sound Track Language (LANGUAGE SETUP) . . . . .
Settings for the Display (SCREEN SETUP). . . . . . . . . . . . . . . . . . . . . . . . . .
Custom Settings (CUSTOM SETUP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Settings for the Sound (AUDIO SETUP) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
55
56
57
59
61
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Self-diagnosis Function (When letters/numbers appear in the display). . . . .
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Language Code List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parental Control Area Code List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
63
66
67
68
68
69
About This Manual
• Instructions in this manual describe the controls on the remote. You can also use the
controls on the player if they have the same or similar names as those on the remote.
• “DVD” may be used as a general term for commercial DVDs, DVD+RWs/DVD+Rs/
DVD+Rs DL (+VR mode) and DVD-RWs/DVD-Rs/DVD-Rs DL (VR mode, video
mode).
• The meaning of the icons used in this manual is described below:
Icons
Meaning
Functions available for commercial DVDs and DVD+RWs/DVD+Rs/
DVD+Rs DL in +VR mode or DVD-RWs/DVD-Rs/DVD-Rs DL in video
mode
Functions available for DVD-RWs/DVD-Rs/DVD-Rs DL in VR (Video
Recording) mode
Functions available for VIDEO CDs (including Super VCDs or CD-Rs/CDRWs in video CD format or Super VCD format)
Functions available for music CDs or CD-Rs/CD-RWs in music CD format
Functions available for DATA CDs (CD-ROMs/CD-Rs/CD-RWs
containing MP3* audio tracks, and JPEG image files)
Functions available for DATA DVDs (DVD-ROMs/DVD+RWs/DVD+Rs/
DVD+Rs DL/DVD-RWs/DVD-Rs/DVD-Rs DL containing MP3* audio
tracks, and JPEG image files)
*MP3 (MPEG-1 Audio Layer III) is a standard format defined by ISO (International Organization for
Standardization)/IEC (International Electrotechnical Commission) MPEG which compresses audio data.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
7US
This Player Can Play the
Following Discs
Format of discs
Commercial DVD
DVD-RW/-R
DVD+RW/+R/
+R DL
VIDEO CD/
Music CD
CD-RW/-R
“DVD+RW,” “DVD-RW,” “DVD+R,”
“DVD+R DL,” “DVD-R,” “DVD VIDEO,”
and “CD” logos are trademarks.
Note about CDs/DVDs
The player can play CD-ROMs/CD-Rs/CDRWs recorded in the following formats:
– music CD format
– video CD format
– MP3 audio tracks and JPEG image files of
format conforming to ISO 9660* Level 1/
Level 2, or its extended format, Joliet
– KODAK Picture CD format
* A logical format of files and folders on CDROMs, defined by ISO (International
Organization for Standardization).
The player can play DVD-ROMs/
DVD-RWs/DVD-Rs/DVD-Rs DL/
DVD+RWs/DVD+Rs/DVD+Rs DL recorded
in the following formats:
– MP3 audio tracks and JPEG image files of
format conforming to UDF (Universal Disk
Format).
Example of discs that the player
cannot play
The player cannot play the following discs:
• CD-ROMs/CD-Rs/CD-RWs other than
those recorded in the formats listed on this
page.
• CD-ROMs recorded in PHOTO CD format.
• Data part of CD-Extras.
• DVD Audio discs.
• HD layer on Super Audio CDs.
• BDs
• HD DVDs
• Disc recorded with an AVCHD-compatible
DVD video camera
Also, the player cannot play the following
discs:
• A commercial DVD with a different region
code.
• A disc recorded in a color system other than
NTSC, such as PAL or SECAM (this player
conforms to the NTSC color system).
• A disc that has a non-standard shape (e.g.,
card, heart).
• A disc with paper or stickers on it.
• A disc that has the adhesive of cellophane
tape or a sticker still left on it.
Region code
Your player has a region code printed on the
back of the unit and only will play
commercial DVDs (playback only) labeled
with identical region codes. This system is
used to protect copyrights.
Commercial DVDs labeled
play on this player.
will also
If you try to play any other commercial DVD,
the message “Playback prohibited by area
limitations.” will appear on the TV screen.
Depending on the commercial DVD, there
may be no region code indication, even
though playing the commercial DVD is
prohibited by area restrictions.
DVP–XXXX
X
00V 00Hz
NO.
00W
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
8
ALL
0-000-000-00
Region code
Notes
• Notes about DVD+RWs/DVD+Rs/DVD+Rs
DL, DVD-RWs/DVD-Rs/DVD-Rs DL or CDRs/CD-RWs
Some DVD+RWs/DVD+Rs/DVD+Rs DL,
DVD-RWs/DVD-Rs/DVD-Rs DL, or CD-Rs/
CD-RWs cannot be played on this player due to
the recording quality or physical condition of the
disc, or the characteristics of the recording device
and authoring software.
The disc will not play if it has not been correctly
finalized. For more information, refer to the
operating instructions for the recording device.
Note that some playback functions may not work
with some DVD+RWs/DVD+Rs/DVD+Rs DL,
even if they have been correctly finalized. In this
case, view the disc by normal playback. Also
some DATA CDs/DATA DVDs created in Packet
Write format cannot be played.
• Music discs encoded with copyright protection
technologies
This product is designed to playback discs that
conform to the Compact Disc (CD) standard.
Recently, various music discs encoded with
copyright protection technologies are marketed
by some record companies. Please be aware that
among those discs, there are some that do not
conform to the CD standard and may not be
playable by this product.
• Note on DualDiscs
A DualDisc is a two sided disc product which
mates DVD recorded material on one side with
digital audio material on the other side.
However, since the audio material side does not
conform to the Compact Disc (CD) standard,
playback on this product is not guaranteed.
Note on playback operations of
DVDs and VIDEO CDs
Some playback operations of DVDs and
VIDEO CDs may be intentionally set by
software producers. Since this player plays
DVDs and VIDEO CDs according to the disc
contents the software producers designed,
some playback features may not be available.
Also, refer to the instructions supplied with
the DVDs or VIDEO CDs.
Copyrights
This product incorporates copyright
protection technology that is protected by
U.S. patents and other intellectual property
rights. Use of this copyright protection
technology must be authorized by
Macrovision, and is intended for home and
other limited viewing uses only unless
otherwise authorized by Macrovision.
Reverse engineering or disassembly is
prohibited.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
9US
Guide to Parts and Controls
For more information, see the pages indicated in parentheses.
Front panel
A [/1 (on/standby) button (26)
G x (stop) button (27)
B Disc tray (26)
H H (play) button (26)
C Front panel display (11)
I A (open/close) button (26)
D
(remote sensor) (22)
E PROGRESSIVE button (19)
F HDMI* (High-Definition Multimedia
Interface) indicator (18, 57, 62)
Lights up when the HDMI OUT jack is
correctly connected to a HDCP (Highbandwidth Digital Content Protection)
compliant device with HDMI or DVI
(Digital Visual Interface) input.
* This DVD player incorporates High-Definition
Multimedia Interface (HDMI™) technology.
“HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC.”
Rear panel
A HDMI OUT (High-Definition
Multimedia Interface out) jack (17)
B DIGITAL OUT (OPTICAL) jack (20)
F S VIDEO OUT jack (17)
G COMPONENT VIDEO OUT jacks
(17)
C DIGITAL OUT (COAXIAL) jack (20)
D LINE OUT L/R (AUDIO) jacks (20)
E LINE OUT (VIDEO) jack (17)
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
10
Front panel display
When playing back a DVD
Playing status
Current title/chapter or playing time (30)
Lights up when you can change the angle (27)
Lights up during Repeat Play (34)
When playing back a VIDEO CD with Playback Control (PBC) (30)
Playing status
Current scene or playing time (30)
Lights up during A-B Repeat Play (35)
When playing back a CD, DATA CD (MP3 audio), DATA DVD (MP3 audio), or VIDEO CD
(without PBC)
Playing status
Current track (30)
Lights up during Repeat Play (34)
Playing time (30)
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
11US
Remote
I ./> PREV/NEXT (previous/
next) buttons (27)
J
m/M
buttons (42)
SCAN/SLOW
K ZOOM button (27, 52)
L SLOW PLAY/FAST PLAY buttons
(27)
M AUDIO button (46)
N SUBTITLE button (27, 52)
O [/1 (on/standby) button (26)
P VOL (volume) +/– buttons (23)
The + button has a tactile dot.*
Q TV/VIDEO button (23)
R PICTURE NAVI (picture navigation)
button (44, 51)
S TIME/TEXT button (30)
T MENU button (29)
U ENTER button (24)
V DISPLAY button (13)
W H PLAY button (26)
The H button has a tactile dot.*
X x STOP button (27)
Y X PAUSE button (27)
Z SUR (surround) button (48)
wj ANGLE button (27)
* Use the tactile dot as a reference when operating
the player.
A TV [/1 (on/standby) button (23)
B Z OPEN/CLOSE button (27)
C Number buttons (29)
The number 5 button has a tactile dot.*
D CLEAR button (32)
E TOP MENU button (29)
F C/X/x/c buttons (29)
G O RETURN button (28)
H
/
REPLAY/STEP/
ADVANCE/STEP buttons (27, 42)
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
12
Guide to the Control Menu Display
Use the Control Menu to select a function and to view related information. Press DISPLAY
repeatedly to turn on or change the Control Menu display as follows:
, Control Menu display 1
m
Control Menu display 2 (appears for certain discs only)
m
Control Menu display off
Control Menu display
The Control Menu display 1 and 2 will show different items depending on the disc type. For
details about each item, see the pages in parentheses.
Example: Control Menu display 1 when playing a DVD VIDEO.
Currently playing chapter number*2
Currently playing title number*1
Total number of titles*1
Total number of chapters*2
Control Menu items
12(27)
18(34)
T
1:32:55
OFF
OFF
SET
ON
Selected item
Function name of
selected Control
Menu item
Operation message
PLAY
DVD VIDEO
Playback status
(N Playback,
X Pause,
x Stop, etc.)
Type of disc
being played*3
Playing time*4
Current setting
Options
PROGRAM
ENTER
Quit: DISPLAY
*1 Displays the scene number for VIDEO CDs
(PBC is on), track number for VIDEO CDs/
CDs, album number for DATA CDs/DATA
DVDs.
2
* Displays the index number for VIDEO CDs,
MP3 audio track number, or JPEG image file
number for DATA CDs/DATA DVDs.
*3 Displays Super VCD as “SVCD.”
4
* Displays the date for JPEG files.
To turn off the display
Press DISPLAY repeatedly.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
13US
List of Control Menu items
Item
Item Name, Function
TITLE (page 43)/SCENE (page 43)/TRACK (page 43)
Selects the title, scene, or track to be played.
CHAPTER (page 43)/INDEX (page 43)
Selects the chapter or index to be played.
TRACK (page 43)
Selects the track to be played.
TIME/TEXT (page 43)
Checks the elapsed time and the remaining playback time.
Input the time code for picture and music searching.
Displays the DVD/CD text or the DATA CD/DATA DVD track/file name.
ORIGINAL/PLAY LIST (page 29)
Selects the type of titles (DVD-VR mode) to be played, the ORIGINAL one, or an edited
PLAY LIST.
PROGRAM (page 32)
Selects the title, chapter, or track to play in the order you want.
SHUFFLE (page 34)
Plays the title, chapter, or track in random order.
REPEAT (page 34)
Plays the entire disc (all titles/all tracks/all albums) repeatedly or one title/chapter/track/
album repeatedly.
A-B REPEAT (page 35)
Specifies the parts you want to play repeatedly.
CUSTOM PICTURE MODE (page 36)
Adjusts the video signal from the player. You can select the picture quality that best suits
the program you are watching.
SHARPNESS (page 37)
Exaggerates the outline of the image to produce a sharper picture.
AV SYNC (page 38)
Adjust the delay between the picture and sound.
PARENTAL CONTROL (page 39)
Set to prohibit playback on this player.
SETUP (page 55)
QUICK Setup (page 24)
Use Quick Setup to choose the desired language of the on-screen display, the aspect ratio
of the TV, and the audio output signal.
CUSTOM Setup
In addition to the Quick Setup setting, you can adjust various other settings.
RESET
Returns the settings in “SETUP” to the default setting.
ALBUM (page 43)
Selects the album that contains MP3 audio track and JPEG image file to be played.
FILE (page 43)
Selects the JPEG image file to be played.
DATE (page 52)
Displays the date the picture was taken by a digital camera.
INTERVAL (page 54)
Specifies the duration for which the slides are displayed on the screen.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
14
EFFECT (page 54)
Selects the effects to be used for changing slides during a slide show.
MODE (MP3, JPEG) (page 53)
Selects the data type; MP3 audio track (AUDIO), JPEG image file (IMAGE), or both
(AUTO) to be played when playing a DATA CD or DATA DVD.
z Hint
The Control Menu icon indicator lights up in green
when you select any item
t
except “OFF” (“PROGRAM,” “SHUFFLE,”
“REPEAT,” “A-B REPEAT,” “SHARPNESS”
only). The “ORIGINAL/PLAY LIST” indicator
lights up in green when you select “PLAY LIST”
(default setting). The “CUSTOM PICTURE
MODE” indicator lights up in green when any
setting other than “STANDARD” is selected. The
“AV SYNC” indicator lights up in green when set
to more than 0 ms.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
15US
Hookups
Hooking Up the Player
Follow steps 1 to 5 to hook up and adjust the settings of the player.
Notes
•
•
•
•
•
See “Specifications” (page 67) for a list of supplied accessories.
Plug cords securely to prevent unwanted noise.
Refer to the instructions supplied with the components to be connected.
You cannot connect this player to a TV that does not have a video input jack.
Be sure to disconnect the power cord of each component before connecting.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
16
Step 1: Connecting the Video Cords/HDMI Cords
Hookups
Connect this player to your TV monitor, projector, or audio component such as an AV amplifier
(receiver) using a video cord. Select one of the patterns A through D, according to the input
jack on your TV monitor, projector, or audio component.
In order to view progressive signal (480p) pictures with a compatible TV, projector, or monitor,
you must use pattern C. Select pattern D when connecting to a TV, projector, or audio
component equipped with HDMI input.
A
(yellow)
INPUT
VIDEO
Audio/video
cord
(supplied)
S VIDEO cord
(not supplied)
INPUT
S VIDEO
L
B
AUDIO
R
TV, projector, or
audio component
TV, projector, or
audio component
(yellow)
to LINE OUT (VIDEO)
to S VIDEO OUT
to HDMI OUT
HDMI cord
(not supplied)
to COMPONENT
VIDEO OUT
(green)
(blue)
CD/DVD player
(red)
Component
video cord
(not supplied)
D
COMPONENT
VIDEO IN
C
Y
(green)
PB
(blue)
PR
(red)
HDMI IN
TV, projector, or
audio component
TV, projector, or
audio component
l : Signal flow
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
17US
2
A Video input jack
You will enjoy standard quality images.
With this connection, select “NORMAL
(INTERLACE)” (default) by pressing the
PROGRESSIVE button on the front panel.
Insert the HDMI connector straight into
the HDMI OUT jack.
Do not bend or apply pressure to the
HDMI connector.
B S VIDEO input jack
You will enjoy high quality images.
With this connection, select “NORMAL
(INTERLACE)” (default) by pressing the
PROGRESSIVE button on the front panel.
C Component video input jacks
(Y, PB, PR)
You will enjoy accurate color reproduction
and high quality images.
If your TV accepts progressive 480p format
signals, use this connection and press the
PROGRESSIVE button on the front panel to
output progressive signals. For details, see
“Using the PROGRESSIVE button”
(page 19).
To connect to a TV with DVI input
Use an HDMI-DVI converter cord (not
supplied). The DVI jack will not accept any
audio signals, so you have to use another
audio connection in addition to this
connection (page 20). Furthermore, you
cannot connect the HDMI OUT jack to DVI
jacks that are not HDCP compliant (e.g., DVI
jacks on PC displays).
When connecting to a standard 4:3 screen
TV
Depending on the disc, the image may not fit
your TV screen. To change the aspect ratio,
see page 57.
D HDMI/DVI input jack
Use a certified Sony HDMI cord to enjoy
high quality digital picture and sound through
the HDMI OUT jack.
When connecting to a Sony TV that is
compatible with the HDMI CONTROL
function, see page 19.
Notes
• Do not connect a VCR, etc., between your TV and
the player. If you pass the player signals via the
VCR, you may not receive a clear image on the
TV screen. If your TV has only one audio/video
input jack, connect the player to this jack.
VCR
When connecting to the HDMI OUT jack
Follow the steps below. Improper handling
may damage the HDMI OUT jack and
the connector.
1
Carefully align the HDMI OUT jack on
the back of the player and the HDMI
connector by checking their shapes.
Make sure the connector is not upside
down or tilted.
Connector is
upside down
CD/DVD player
• If the picture appears too white when you are
using A or B connection, set “BLACK LEVEL”
in “SCREEN SETUP” to “OFF” (page 59).
• Be sure to disconnect the HDMI cord when
moving the player.
• Do not apply too much pressure to the cabinet
wall, if you place the player on the cabinet with
the HDMI cord connected. It may damage the
HDMI OUT jack or the HDMI cord.
• When connecting or disconnecting, do not screw
in or rotate the HDMI connector.
Not straight
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
18
TV
Connect
directly
About the HDMI CONTROL
functions for ‘BRAVIA’ Theatre
Sync (for HDMI connections only)
To prepare for the ‘BRAVIA’ Theatre Sync
features
Set “HDMI CONTROL” to “ON” in “CUSTOM
SETUP” (page 60). For details on TV setting, refer
to the operating instructions supplied with the TV.
Note
Depending on the connected component, the HDMI
CONTROL function may not work. Refer to the
operating instructions supplied with the component.
Using the PROGRESSIVE button
By using the PROGRESSIVE button on the
front panel, you can select the signal format in
which the player outputs video signals
(Progressive or Interlace), and the conversion
method for progressive signals.
Each time you press PROGRESSIVE button,
the display changes as follows:
,
PROGRESSIVE AUTO
m
PROGRESSIVE VIDEO
m
NORMAL (INTERLACE)
◆PROGRESSIVE AUTO
Select this setting when:
– your TV accepts progressive signals, and,
– the TV is connected to the COMPONENT
VIDEO OUT jacks.
Normally select this under the above
condition. This automatically detects the
software type, and selects the appropriate
conversion method.
Note that the picture will not be clear or no
picture will appear if you select these settings
when either of the above conditions is not met.
Hookups
By connecting to Sony components that are
compatible with the HDMI CONTROL function
with an HDMI cord (not supplied), you can enjoy
the following features:
• One-Touch Play (page 26)
• System-Power Off
When you turn the TV off by using the [/1 button
on the TV’s remote, the components compatible
with HDMI CONTROL function turn off
automatically.
◆PROGRESSIVE VIDEO
Select this setting when:
– your TV accepts progressive signals, and,
– the TV is connected to the COMPONENT
VIDEO OUT jacks, and,
– you want to fix the conversion method to
PROGRESSIVE VIDEO for video-based
software.
Select this if the image is not clear when you
select PROGRESSIVE AUTO.
Note that the picture will not be clear or no
picture will appear if you select these settings
when either of the above conditions is not
met.
◆NORMAL (INTERLACE)
Select this setting when:
– your TV does not accept progressive
signals, or,
– your TV is connected to jacks other than the
COMPONENT VIDEO OUT jacks (LINE
OUT (VIDEO) or S VIDEO OUT).
About DVD software types and the
conversion method
DVD software can be divided into two types:
film-based software and video-based
software.
Video-based software is derived from TV,
such as dramas and sitcoms, and displays
images at 30 frames/60 fields per second.
Film-based software is derived from film and
displays images at 24 frames per second.
Some DVD software contains both video and
film.
In order for these images to appear natural on
your screen when output in progressive
format, the progressive signals need to be
converted to match the type of DVD software
that you are watching.
Note
When you play video-based software in progressive
signal format, sections of some types of images may
appear unnatural due to the conversion process
when output through the COMPONENT VIDEO
OUT jacks. Images from the S VIDEO OUT and
LINE OUT (VIDEO) jacks are unaffected as they
are output in the normal (interlace) format.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
19US
Step 2: Connecting the Audio Cords
Select one of the following patterns A or B, according to the input jack on your TV monitor,
projector, or audio component such as an AV amplifier (receiver).
This will enable you to listen to sound.
(red)
INPUT
(yellow)*
Audio/video
cord (supplied)
VIDEO
A
(white)
(white)
L
(yellow)*
AUDIO
(red)
R
TV, projector, or
audio component
to LINE OUT L/R (AUDIO)
to DIGITAL OUT (COAXIAL or
OPTICAL)/HDMI OUT
CD/DVD player
COAXIAL
OPTICAL
HDMI OUT
DIGITAL OUT
or
or
Optical digital cord
(not supplied)
Remove jack cap
before connecting
Coaxial digital cord
(not supplied)
HDMI cord (not supplied)
to coaxial or optical/
HDMI digital input
[Speakers]
Rear (L)
Rear (R)
Front (L)
Center
B
[Speakers]
Front (R)
Audio component
with a decoder
Subwoofer
: Signal flow
* The yellow plug is used for video signals (page 17).
z Hint
For correct speaker location, see the operating instructions supplied with the connected components.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
20
A Audio L/R input jacks
This connection will use your TV’s or audio
component’s two speakers for sound.
B Digital audio input jack
*1
Manufactured under license from Dolby
Laboratories.
Dolby, Pro Logic, and the double-D symbol are
trademarks of Dolby Laboratories.
*2 “DTS” and “DTS Digital Out” are registered
trademarks of DTS, Inc.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
Hookups
If your audio component has a Dolby*1
Digital or DTS*2 decoder and a digital input
jack, use this connection. You can enjoy
Dolby Digital (5.1ch) and DTS (5.1ch)
surround effect.
If you connect to a Sony audio component
that is compatible with the HDMI
CONTROL function, refer to the operating
instructions supplied with the audio
component.
Notes
• After you have completed the connection, be sure
to set “DOLBY DIGITAL” to “DOLBY
DIGITAL” and “DTS” to “ON” in Quick Setup
(page 24).
• When you connect an audio component that
conforms to the 96 kHz sampling frequency, set
“48kHz/96kHz PCM” in “AUDIO SETUP” to
“96kHz/24bit” (page 62).
• The TVS effects of this player cannot be used
with this connection.
• When you connect the player to an audio
component using an HDMI cord, you will need to
do one of the following:
– Connect the audio component to the TV with the
HDMI cord.
– Connect the player to the TV with a video cord
other than HDMI cord (component video cord, S
VIDEO cord, or audio/video cord).
• When connecting to the HDMI OUT jack,
carefully align the HDMI connector with the jack.
Do not bend and apply pressure to the HDMI
cord.
21US
Step 3: Connecting the Power Cord
Plug the player and TV power cords into an AC outlet.
Step 4: Preparing the Remote
You can control the player using the supplied remote. Insert two R6 (size AA) batteries by
matching the 3 and # ends on the batteries to the markings inside the compartment. When
using the remote, point it at the remote sensor
on the player.
Notes
• Do not leave the remote in an extremely hot or humid place.
• Do not drop any foreign object into the remote casing, particularly when replacing the batteries.
• Do not expose the remote sensor to direct light from the sun or a lighting apparatus. Doing so may cause a
malfunction.
• If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage
from battery leakage and corrosion.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
22
Controlling other TVs with the
remote
You can control the sound level, input source,
and power switch of your Sony TV with the
supplied remote.
You can control the sound level, input source,
and power switch of non-Sony TVs as well.
If your TV is listed in the table below, set the
appropriate manufacturer’s code.
TV
Number
buttons
1
While holding down TV [/1, press the
number buttons to select your TV’s
manufacturer’s code (see the table
below).
2
Release TV [/1.
VOL +/–
TV/VIDEO
Hookups
Controlling Your TV with the
Supplied Remote
Code numbers of controllable TVs
If more than one code number is listed, try
entering them one at a time until you find the
one that works with your TV.
Manufacturer
Code number
You can control your TV using the buttons
below.
Sony
01 (default)
Daewoo
04, 22
By pressing
You can
Hitachi
02, 04
TV [/1
Turn the TV on or off
JVC
09
VOL +/–
Adjust the volume of the TV
LG/Goldstar
04
Switch the TV’s input source
between the TV and other
input sources
MGA/Mitsubishi 04, 13
TV/VIDEO
Note
• Depending on the connected unit, you may not be
able to control your TV using all or some of the
buttons on the supplied remote.
Panasonic
19
Philips
21
RCA
04, 10
Samsung
04, 20
Sharp
18
Toshiba
07, 18
Notes
• When you replace the batteries of the remote, the
code number you have set may be reset to the
default setting. Set the appropriate code number
again.
• Depending on the connected unit, you may not be
able to control your TV using all or some of the
buttons on the supplied remote.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
23US
Step 5: Quick Setup
Follow the steps below to make the minimum number of basic adjustments for using the player.
To skip an adjustment, press >. To return to the previous adjustment, press ..
ENTER
1 Turn on the TV.
2 Press [/1.
3 Switch the input selector on your
5 Press X/x to select a language.
TV so that the signal from the
player appears on the TV screen.
The Setup Display for selecting the
aspect ratio of the TV to be connected
appears.
“Press [ENTER] to run QUICK SETUP”
(press enter to run Quick Setup) appears
at the bottom of the screen. If this
message does not appear, select
“QUICK” (quick) under “SETUP”
(setup) in the Control Menu to run Quick
Setup (page 56).
4 Press ENTER without inserting a
disc.
The Setup Display for selecting the
language used in the on-screen display
appears.
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
ENGLISH
ENGLISH
FRENCH
SPANISH
PORTUGUESE
The player displays the menu and
subtitles in the selected language.
6 Press ENTER.
SCREEN SETUP
16:9
TV TYPE:
16:9
HDMI RESOLUTION:
JPEG RESOLUTION: 4:3 LETTER BOX
4:3 PAN SCAN
YCBCR/RGB (HDMI):
ON
SCREEN SAVER:
JACKET PICTURE
BACKGROUND:
ON
BLACK LEVEL:
OFF
BLACK LEVEL (COMPONENT OUT):
FULL
4:3 OUTPUT:
7 Press X/x to select the setting that
matches your TV type.
◆ If you have a wide-screen TV or a 4:3
standard TV with a wide-screen mode
• 16:9 (page 57)
◆ If you have a 4:3 standard TV
• 4:3 LETTER BOX or 4:3 PAN SCAN
(page 57)
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
24
8 Press ENTER.
The Setup Display for selecting the type
of jack used to connect your audio
component appears.
YES
LINE OUTPUT L/R(AUDIO)
DIGITAL OUTPUT
“DTS” is selected.
AUDIO SETUP
AUDIO DRC:
STANDARD
DOWNMIX:
DOLBY SURROUND
DIGITAL OUT:
ON
D-PCM
DOLBY DIGITAL:
DTS:
OFF
OFF
48kHz/96kHz PCM:
ON
AUDIO (HDMI):
Hookups
Is this player connected to an amplifier
(receiver)? Select the type of jack you
are using.
11Press ENTER.
NO
X/x to select whether or
9 Press X/x to select the type of jack 12notPress
you wish to send a DTS signal
(if any) you are using to connect to
an audio component, then press
ENTER.
If you did not connect an audio
component, select “NO,” then go to step
13.
If you connected an audio component
using just an audio cord, select “YES:
LINE OUTPUT L/R (AUDIO),” then go
to step 13.
If you connected an audio component
using a digital coaxial or optical/HDMI
cord, select “YES: DIGITAL OUTPUT.”
to your audio component.
If your audio component has a DTS
decoder, select “ON.” Otherwise, select
“OFF.”
13Press ENTER.
Quick Setup is finished. All connections
and setup operations are complete.
10Press X/x to select the type of
Dolby Digital signal you wish to
send to your audio component.
If your audio component has a Dolby
Digital decoder, select “DOLBY
DIGITAL.” Otherwise, select “D-PCM.”
AUDIO SETUP
AUDIO DRC:
STANDARD
DOWNMIX:
DOLBY SURROUND
DIGITAL OUT:
ON
D-PCM
DOLBY DIGITAL:
DTS:
D-PCM
48kHz/96kHz PCM: DOLBY DIGITAL
AUDIO (HDMI):
AUTO
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
25US
4 Press A on the player, and place a
disc on the disc tray.
Playback
Playing Discs
Depending on the DVD or VIDEO CD, some
operations may be different or restricted.
Refer to the operating instructions supplied
with your disc.
TIME/TEXT
RETURN
MENU
ENTER
DISPLAY
REPLAY
ADVANCE
ZOOM
SLOW PLAY
SUBTITLE
5 Press H.
The disc tray closes. The player starts
playback (continuous play). Adjust the
volume on the TV or the audio
component.
Depending on the disc, a menu may
appear on the TV screen. For DVD
VIDEOs, see page 29. For VIDEO CDs,
see page 30.
Number
buttons
CLEAR
TOP MENU
Playback side facing down
FAST PLAY
ANGLE
1 Turn on your TV.
2 Press [/1.
The player turns on.
3 Switch the input selector on your
TV so that the signal from the
player appears on the TV screen.
To turn off the player
Press [/1. The player enters standby mode.
One-Touch Play (for HDMI connections
only)
With one touch of the H button on the
remote, the player and your TV automatically
turn on and the TV’s input is switched to the
player. Playback starts automatically.
The TV’s input will also switch to the player
automatically, in the following cases:
– You press H, TOP MENU, MENU, or
DISPLAY buttons on the remote.
Note that these buttons are not effective
when you play audio CD or MP3 audio
track in “AUDIO (MP3)” mode.
– If a disc with auto play function is loaded.
z Hint
You can have the player turn off automatically
whenever you leave it in stop mode for more than
30 minutes. To turn this function on or off, set
“AUTO POWER OFF” in “CUSTOM SETUP” to
“ON” or “OFF” (page 59).
◆ When using an audio component
Turn on the audio component and select
the appropriate channel so that you can
hear sound from the player.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
26
Notes on playing DTS sound tracks on a
DVD VIDEO
Note
Discs created on DVD recorders must be correctly
finalized before they can be played. For more
information about finalizing, refer to the operating
instructions supplied with the DVD recorder.
Additional operations
To check the position of the buttons below,
see the illustration on page 26.
To
Operation
Stop
Press x
Pause
Press X
Resume play after
pause
Press X or H
Playback
• DTS audio signals are output only through
the DIGITAL OUT (COAXIAL or
OPTICAL)/HDMI OUT jack.
• When you play a DVD VIDEO with DTS
sound tracks, set “DTS” to “ON” in
“AUDIO SETUP” (page 62).
• If you connect the player to audio
equipment without a DTS decoder, do not
set “DTS” to “ON” in “AUDIO SETUP”
(page 62). A loud noise may come out from
the speakers, affecting your ears or causing
the speakers to be damaged.
Go to the next chapter, Press >
track or scene in
continuous play mode
Press .
Go back to the
previous chapter,
track or scene in
continuous play mode
Stop play and remove Press Z
the disc
Change the angle
Press ANGLE during
playback.
Press ANGLE
repeatedly to select an
angle number.
Display the subtitle
Press SUBTITLE
during playback.
Press SUBTITLE
repeatedly to select a
subtitle language.
Replay the previous
scene*1
Press
REPLAY during
playback
Briefly fast forward
the current scene*2
Press
ADVANCE during
playback
Magnify the image*3
Press ZOOM
repeatedly. Press
CLEAR to cancel.
*1 All DVDs except for DVD+Rs/DVD+RWs/
DVD+Rs DL.
*2 DVDs only.
*3 Video and JPEG pictures only (except
BACKGROUND pictures). You can move the
enlarged picture using C/X/x/c. Depending
upon the contents of the disc, the zoom function
may be canceled automatically when the picture
is moved.
Note
You may not be able to use the Replay or Advance
function with some scenes.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
27US
Playing quickly or slowly with
sound
You can listen to dialog or sound while
playing the current scene quickly or slowly.
During playback, press FAST PLAY or
SLOW PLAY.
The speed changes when you press either
FAST PLAY or SLOW PLAY.
To return to normal playback
Press H.
Notes
• You can only use this function with DVDs,
VIDEO CDs, or Super VCDs only.
• “Operation not possible” will appear when
maximum or minimum speed is reached.
• During Fast Play or Slow Play mode, you cannot
change the angle (page 27), subtitle (page 27), or
sound (page 46). The sound can only be changed
for VIDEO CDs/Super VCDs.
• Fast Play and Slow Play functions do not work
when playing DTS sound tracks.
• You cannot use Fast Play or Slow Play functions
when playing a still picture in DVD-VR mode.
Locking the disc tray (Child
Lock)
You can lock the disc tray to prevent children
from opening it.
When the player is in standby mode, press
O RETURN, ENTER, and then [/1 on the
remote.
The player turns on and “LOCKED” appears
on the front panel display. The A and Z
buttons on the player or the remote do not
work while the Child Lock is set.
To unlock the disc tray
When the player is in standby mode, press
O RETURN, ENTER, and then [/1 again.
Note
Even if you select “RESET” under “SETUP” in the
Control Menu (page 56), the disc tray remains
locked.
Resuming Playback From the
Point Where You Stopped the
Disc (Multi-disc Resume)
The player stores the point where you stopped
the disc for up to 6 discs and resumes
playback the next time you insert the same
disc. If you store a resume playback point for
the 7th disc, the resume playback point for the
first disc is deleted.
1 While playing a disc, press x to
stop playback.
“RESUME” appears on the front panel
display.
2 Press H.
The player starts playback from the point
where you stopped the disc in step 1.
z Hint
To play from the beginning of the disc, press x
twice, then press H.
Notes
• “MULTI-DISC RESUME” in “CUSTOM
SETUP” must be set to “ON” (default) for this
function to work (page 60).
• The point where you stopped playing is cleared
when:
– you change the play mode.
– you change the settings on the Setup Display.
• For DVD-VR mode, CDs, DATA CDs, and
DATA DVDs, the player remembers the resume
playback point for the current disc.
The resume point is cleared when:
– you opened the disc tray.
– you disconnect the power cord.
– the player enters standby mode (DATA CD/
DATA DVD only).
• Resume Play does not work during Shuffle Play
and Program Play.
• This function may not work with some discs.
• If “MULTI-DISC RESUME” in “CUSTOM
SETUP” is set to “ON” and you playback a
recorded disc such as DVD-RW, the player may
playback other recorded discs from the same
resume point.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
28
Using the DVD’s Menu
1 Press TOP MENU or MENU.
The disc’s menu appears on the TV
screen.
The contents of the menu vary from disc
to disc.
2 Press C/X/x/c or the number
buttons to select the item you want
to play or change.
If you press the number buttons, the
following display appears.
Press the number buttons to select the
item you want.
Some DVD-VR (Video Recording) mode
have two types of titles for playback:
originally recorded titles (ORIGINAL) and
titles that can be created on recordable DVD
players for editing (PLAY LIST). You can
select the type of title to be played.
1 Press DISPLAY when the player is
Playback
A DVD VIDEO is divided into long sections
of a picture or a music feature called “titles.”
When you play a DVD VIDEO which
contains several titles, you can select the title
you want using the TOP MENU button.
When you play DVD VIDEOs that allow you
to select items such as language for the sound
and subtitles, select these items using the
MENU button.
Selecting “ORIGINAL” or “PLAY
LIST” in DVD-VR mode
in stop mode.
The Control Menu appears.
2 Press X/x to select
(ORIGINAL/PLAY LIST), then press
ENTER.
The options for “ORIGINAL/PLAY
LIST” appear.
12(27)
18(34)
T
1:32:55
PLAY LIST
PLAY LIST
ORIGINAL
DVD-VR
1
3 Press X/x to select a setting.
3 Press ENTER.
• PLAY LIST: plays the titles created
from “ORIGINAL” for editing.
• ORIGINAL: plays the titles originally
recorded.
4 Press ENTER.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
29US
Playing VIDEO CDs With PBC
Functions (PBC Playback)
PBC (Playback Control) allows you to play
VIDEO CDs interactively by following the
menu on the TV screen.
1 Start playing a VIDEO CD with PBC
functions.
The menu for your selection appears.
2 Press the number buttons to select
Checking the Playing Time and
Remaining Time
You can check the playing time and remaining
time of the current title, chapter, or track. Also,
you can check the DVD/CD text or track name
(MP3 audio) recorded on the disc.
1 Press TIME/TEXT during playback.
The following display appears.
T 1:01:57
the item number you want.
3 Press ENTER.
4 Follow the instructions in the
Time
information
2 Press TIME/TEXT repeatedly to
menu for interactive operations.
change the time information.
Refer to the instructions supplied with the
disc, as the operating procedure may
differ depending on the VIDEO CD.
The available time information depends
upon the type of disc you are playing.
To return to the menu
Press O RETURN.
z Hint
To play without using PBC, press ./> or the
number buttons while the player is stopped to select
a track, then press H or ENTER.
“Play without PBC” appears on the TV screen and
the player starts continuous play. You cannot play
still pictures such as a menu.
To return to PBC playback, press x twice then
press H.
Note
Depending on the VIDEO CD, “Press ENTER” in
step 3 may appear as “Press SELECT” in the
instructions supplied with the disc. In this case,
press H.
◆ When playing a DVD
• T *:*:* (hours: minutes: seconds)
Playing time of the current title
• T–*:*:*
Remaining time of the current title
• C *:*:*
Playing time of the current chapter
• C–*:*:*
Remaining time of the current chapter
◆ When playing a VIDEO CD or Super
VCD (with PBC functions)
• *:* (minutes: seconds)
Playing time of the current scene
◆ When playing a VIDEO CD (without
PBC functions) or CD
• T *:* (minutes: seconds)
Playing time of the current track
• T–*:*
Remaining time of the current track
• D *:*
Playing time of the current disc
• D –*:*
Remaining time of the current disc
◆ When playing a Super VCD (without
PBC functions)
• T *:* (minutes: seconds)
Playing time of the current track
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
30
◆ When playing a DATA CD (MP3 audio)
or DATA DVD (MP3 audio)
• T *:* (minutes: seconds)
Playing time of the current track
Checking the play information of
the disc
Press TIME/TEXT repeatedly in step 2 to
display text recorded on the DVD/CD.
The DVD/CD text appears only when text is
recorded in the disc. You cannot change the
text. If the disc does not contain text, “NO
TEXT” appears.
To check DATA CD/DATA DVD album
name, etc.
By pressing TIME/TEXT while playing MP3
audio tracks on a DATA CD/DATA DVD,
you can display the name of the album/track
and the audio bit rate (the amount of data per
second of the current audio track) on your TV
screen.
You can view the time information and text
displayed on the TV screen also on the front
panel display. The information on the front
panel display changes as follows when you
change the time information on your TV
screen.
When playing a DVD
Playback
To check the DVD/CD text
Checking the information on the
front panel display
Playing time of the current title
Remaining time of the
current title
Playing time of the current
chapter
Bit rate
T
17:30
128k
Remaining time of the
current chapter
Text
JAZZ
RIVER SIDE
Album name
Track name
Current title and chapter
number
(returns to top automatically)
When playing a DATA CD (MP3 audio) or
DATA DVD (MP3 audio)
,
Playing time and number of the
current track
,
Track name
,
Current album and track number
(returns to top automatically)
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
31US
When playing a VIDEO CD (without PBC
functions) or CD
,
Playing time and number of the
current track
,
Remaining time of the current track
Various Play Mode
Functions (Program Play,
Shuffle Play, Repeat Play, A-B Repeat
,
Play)
Playing time of the disc
,
Remaining time of the disc
,
Text
z Hints
• When playing VIDEO CDs without PBC
functions, the track number, and the index number
are displayed after the text.
• When playing VIDEO CDs with PBC functions,
the scene number, or the playing time are
displayed.
• Long text that does not fit in a single line will
scroll across the front panel display.
• You can also check the time information and text
using the Control Menu (page 13).
Notes
• Depending on the type of disc being played, the
DVD/CD text or track name may not be
displayed.
• The player can only display the first level of the
DVD/CD text, such as the disc name or title.
• Playing time of MP3 audio tracks may not be
displayed correctly.
• If you play a disc containing JPEG image files
only, “BGM” appears when “MODE (MP3,
JPEG)” is set to “AUTO” or “AUTO (BGM),”
and “JPEG” appears when “MODE (MP3,
JPEG)” is set to “IMAGE (JPEG)” in the front
panel display.
You can set the following play modes:
• Program Play (page 32)
• Shuffle Play (page 34)
• Repeat Play (page 34)
• A-B Repeat Play (page 35)
Note
The play mode is canceled when:
– you open the disc tray.
– the player enters standby mode by pressing [/1.
Creating your own program
(Program Play)
You can play the contents of a disc in the
order you want by arranging the order of the
titles, chapters, or tracks on the disc to create
your own program. You can program up to 99
titles, chapters, and tracks.
1
Press DISPLAY.
The Control Menu appears.
2
Press X/x to select
(PROGRAM), then press ENTER.
The options for “PROGRAM” appear.
12(27)
18(34)
T
1:32:55
OFF
OFF
SET
ON
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
32
PLAY
DVD VIDEO
3
Press X/x to select “SET t,” then
press ENTER.
PROGRAM
ALL CLEAR
1. TITLE 0 2 – 0 3
2. TITLE – –
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
“TRACK” is displayed when you play
a VIDEO CD or CD.
PROGRAM
T
––
01
02
03
04
05
Selected title and chapter
◆ When playing a VIDEO CD or CD
For example, select track “02.”
Press X/x to select “02” under “T,” then
press ENTER.
Titles or tracks
recorded on a disc
4
Selected track
Press c.
PROGRAM
ALL CLEAR
1. TITLE – –
2. TITLE – –
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
T
C
––
01
02
03
04
05
ALL
01
02
03
04
05
06
ALL CLEAR
1. TRACK
2. TRACK
3. TRACK
4. TRACK
5. TRACK
6. TRACK
7. TRACK
◆ When playing a DVD VIDEO
For example, select chapter “03” of title
“02.”
Press X/x to select “02” under “T,” then
press ENTER.
PROGRAM
ALL CLEAR
1. TITLE – –
2. TITLE – –
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
T
C
––
01
02
03
04
05
ALL
01
02
03
04
05
06
Next, press X/x to select “03” under “C,”
then press ENTER.
02
––
––
––
––
––
––
––
01
02
03
04
05
Total time of the programmed tracks
6
Chapters recorded on a disc
Select the title, chapter, or track you
want to program.
0:15:30
T
PROGRAM
The cursor moves to the title or track row
“T” (in this case, “01”).
5
Playback
ALL CLEAR
1. TITLE
2. TITLE – –
3. TITLE – –
4. TITLE – –
5. TITLE – –
6. TITLE – –
7. TITLE – –
T
––
01
02
03
04
05
To program other titles, chapters, or
tracks, repeat steps 4 to 5.
The programmed titles, chapters, and
tracks are displayed in the selected order.
7
Press H to start Program Play.
Program Play begins.
When the program ends, you can restart
the same program again by pressing H.
To return to normal play
Press CLEAR, or select “OFF” in step 3. To
play the same program again, select “ON” in
step 3 and press ENTER.
To change or cancel a program
1
Follow steps 1 to 3 of “Creating your own
program (Program Play).”
2
Select the program number of the title,
chapter, or track you want to change or
cancel using X/x and press c. If you
want to delete the title, chapter, or track
from the program, press CLEAR.
3
Follow step 5 for new programming. To
cancel a program, select “--” under “T,”
then press ENTER.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
33US
To cancel all of the titles, chapters, or
tracks in the programmed order
1
Follow steps 1 to 3 of “Creating your own
program (Program Play).”
2
3
Press X and select “ALL CLEAR.”
Press ENTER.
z Hint
You can perform Repeat Play, or Shuffle Play of
programmed titles, chapters, or tracks. During
Program Play, follow the steps of Repeat Play (page
34) or Shuffle Play (page 34).
4
Press ENTER.
Shuffle Play starts.
To return to normal play
Press CLEAR, or select “OFF” in step 3.
z Hints
• You can set Shuffle Play while the player is
stopped. After selecting the “SHUFFLE” option,
press H. Shuffle Play starts.
• Up to 200 chapters in a disc can be played in
random order when “CHAPTER” is selected.
Note
Notes
• When you program tracks on a Super VCD, the
total playing time is not displayed.
• You cannot use this function with VIDEO CDs or
Super VCDs with PBC playback.
Playing in random order (Shuffle
Play)
You cannot use this function with VIDEO CDs or
Super VCDs with PBC playback.
Playing repeatedly (Repeat Play)
You can have the player “shuffle” titles,
chapters, or tracks. Subsequent “shuffling”
may produce a different playing order.
You can play all of the titles or tracks on a
disc, or a single title, chapter, or track
repeatedly.
You can use a combination of Shuffle or
Program Play modes.
1
1
Press DISPLAY during playback.
2
Press X/x to select
(SHUFFLE), then press ENTER.
2
12(27)
18(34)
T
1:32:55
PLAY
DVD VIDEO
OFF
OFF
TITLE
CHAPTER
3
Press X/x to select the item to be
shuffled.
◆ When playing a DVD VIDEO
• TITLE
• CHAPTER
◆ When playing a VIDEO CD or CD
• TRACK
Press X/x to select
(REPEAT), then press ENTER.
The options for “REPEAT” appear.
The options for “SHUFFLE” appear.
12(27)
18(34)
T
1:32:55
Press DISPLAY during playback.
The Control Menu appears.
The Control Menu appears.
OFF
OFF
DISC
TITLE
CHAPTER
3
Press X/x to select the item to be
repeated.
◆ When playing a DVD VIDEO
• DISC: repeats all of the titles.
• TITLE: repeats the current title on a
disc.
• CHAPTER: repeats the current chapter.
◆ When Program Play is activated
• ON: shuffles titles, chapters, or tracks
selected in Program Play.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
34
DVD VIDEO
◆ When playing in DVD-VR mode
• DISC: repeats all the titles of the
selected type.
• TITLE: repeats the current title on a
disc.
• CHAPTER: repeats the current chapter.
◆ When playing a VIDEO CD or CD
• DISC: repeats all of the tracks.
• TRACK: repeats the current track.
You can play a specific portion of a title,
chapter, or track repeatedly. (This function is
useful when you want to memorize lyrics,
etc.)
1
The Control Menu appears.
2
◆ When Program Play or Shuffle Play is
activated
• ON: repeats Program Play or Shuffle
Play.
4
Press DISPLAY during playback.
Press X/x to select
(A-B
REPEAT), then press ENTER.
The options for “A-B REPEAT”
appear.
12(27)
18(34)
T
1:32:55
Press ENTER.
Playback
◆ When playing a DATA CD or DATA DVD
• DISC: repeats all of the albums.
• ALBUM: repeats the current album.
• TRACK (MP3 audio tracks only):
repeats the current track.
Repeating a specific portion
(A-B Repeat Play)
PLAY
DVD VIDEO
Repeat Play starts.
OFF
SET
OFF
To return to normal play
Press CLEAR, or select “OFF” in step 3.
z Hint
You can set Repeat Play while the player is stopped.
After selecting the “REPEAT” option, press H.
Repeat Play starts.
3
Press X/x to select “SET t,” then
press ENTER.
The “A-B REPEAT” setting bar appears.
A 18 - 1:32:30
B
Notes
• You cannot use this function with VIDEO CDs or
Super VCDs with PBC playback.
• When repeating a DATA CD/DATA DVD which
contains MP3 audio tracks and JPEG image files,
and their playing times are not the same, the sound
will not match the image.
• When “MODE (MP3, JPEG)” is set to “IMAGE
(JPEG)” (page 53), you cannot select “TRACK.”
4
During playback, when you find the
starting point (point A) of the portion to
be played repeatedly, press ENTER.
The starting point (point A) is set.
A 18 - 1:32:55
5
B 18 - 1:33:05
When you reach the ending point
(point B), press ENTER again.
The set points are displayed and the
player starts repeating this specific
portion.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
35US
To return to normal play
Press CLEAR, or select “OFF” in step 3.
Notes
• When you set A-B Repeat Play, the settings for
Shuffle Play, Repeat Play, and Program Play are
canceled.
• A-B Repeat Play does not work across multiple
titles.
• You may not set A-B Repeat Play for contents in
DVD-VR mode that contains still pictures.
Adjusting the Playback
Picture (CUSTOM PICTURE MODE)
You can adjust the video signal of the DVD,
VIDEO CD, or DATA CD/DATA DVD in
JPEG format from the player to obtain the
picture quality you want. Choose the setting
that best suits the program you are watching.
When you select “MEMORY,” you can make
further adjustments to each element of the
picture (color, brightness, etc.).
1 Press DISPLAY twice during
playback.
The Control Menu appears.
2 Press X/x to select
(CUSTOM PICTURE MODE), then
press ENTER.
The options for “CUSTOM PICTURE
MODE” appear.
STANDARD
STANDARD
DYNAMIC 1
DYNAMIC 2
CINEMA 1
CINEMA 2
MEMORY
DVD VIDEO
3 Press X/x to select the setting you
want.
The default setting is underlined.
• STANDARD: displays a standard picture.
• DYNAMIC 1: produces a bold
dynamic picture by increasing the
picture contrast and the color intensity.
• DYNAMIC 2: produces a more
dynamic picture than DYNAMIC 1 by
further increasing the picture contrast
and color intensity.
• CINEMA 1: enhances details in dark
areas by increasing the black level.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
36
• CINEMA 2: white colors become
brighter and black colors become richer
and the color contrast is increased.
• MEMORY: adjusts the picture in
greater detail.
Sharpening the Picture
(SHARPNESS)
4 Press ENTER.
You can enhance the outlines of images to
produce a sharper picture.
The selected setting takes effect.
1 Press DISPLAY twice during
playback.
Playback
z Hint
When you watch a movie, “CINEMA 1” or
“CINEMA 2” is recommended.
The Control Menu appears.
Adjusting the picture items in
“MEMORY”
You can adjust each element of the picture
individually.
• PICTURE: changes the contrast
• BRIGHTNESS: changes the overall
brightness
• COLOR: makes the colors deeper or lighter
• HUE: changes the color balance
1
In step 3 of “Adjusting the Playback
Picture,” select “MEMORY” and press
ENTER.
The “PICTURE” adjustment bar appears.
2 Press X/x to select
(SHARPNESS), then press ENTER.
The options for “SHARPNESS” appear.
OFF
OFF
1
2
DVD VIDEO
3 Press X/x to select a level.
• 1: enhances the outline.
• 2: enhances the outline more than 1.
4 Press ENTER.
PICTURE
2
0
Press C/c to adjust the picture
contrast.
To go to the next or previous picture item
without saving the current setting, press
X/x.
3
The selected setting takes effect.
To cancel the “SHARPNESS” setting
Select “OFF” in step 3.
Press ENTER.
The adjustment is saved and
“BRIGHTNESS” adjustment bar
appears.
4
Repeat step 2 and 3 to adjust
“BRIGHTNESS,” “COLOR,” and
“HUE.”
To turn off the display
Press O RETURN or DISPLAY.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
37US
To reset the “AV SYNC” setting
Adjusting the Delay
Between the Picture and
Sound (AV SYNC)
When the sound does not match the pictures
on the screen, you can adjust the delay
between the picture and sound.
1 Press DISPLAY twice during
playback.
Press CLEAR in step 4.
Notes
• This function is not effective if you use the
DIGITAL OUT (OPTICAL or COAXIAL)
jack, and set “DOLBY DIGITAL” or
“DTS” in AUDIO SETUP to “DOLBY
DIGITAL” or “ON” respectively (page 61).
• This function is not effective if you connect
a Dolby Digital or DTS-compliant device
via the HDMI OUT jack, and set “DOLBY
DIGITAL” or “DTS” in AUDIO SETUP to
“DOLBY DIGITAL” or “ON” respectively
(page 61).
The Control Menu appears.
2 Press X/x to select
(AV
SYNC), then press ENTER.
The following display appears.
STOP
DVD VIDEO
0 ms
SET
3 Press x to select “SET c”, then
press ENTER.
The “AV SYNC” adjustment bar
appears.
AV SYNC
0ms
4 Press c repeatedly to adjust the
delay.
Each time you press C/c, the delay is
adjusted by 10 milliseconds.
5 Press ENTER.
The selected setting takes effect.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
38
Locking Discs (CUSTOM
4
◆ If you have not entered a password
The display for registering a new
password appears.
PARENTAL CONTROL, PARENTAL
CONTROL)
You can set two kinds of playback restrictions
for a disc.
• Custom Parental Control
You can set playback restrictions so that the
player will not play inappropriate discs.
• Parental Control
Playback of some DVD VIDEOs can be
limited according to a predetermined level
such as the age of the users. Scenes may be
blocked or replaced with different scenes.
The same password is used for both Parental
Control and Custom Parental Control.
PARENTAL CONTROL
1
Enter a 4-digit password using the
number buttons, then press ENTER.
The display for confirming the password
appears.
◆ When you have already registered a
password
The display for entering the password
appears.
5
Press DISPLAY while the player is in
stop mode.
The Control Menu appears.
3
Press X/x to select
(PARENTAL CONTROL), then press
ENTER.
The options for “PARENTAL
CONTROL” appear.
12(27)
18(34)
T
1:32:55
Enter or re-enter your 4-digit password
using the number buttons, then press
ENTER.
“Custom parental control is set.” appears
and then the screen returns to the Control
Menu.
Insert the disc you want to lock.
If the disc is playing, press x to stop
playback.
2
Playback
Enter a new 4-digit password,
then press ENTER .
Custom Parental Control
You can set the same Custom Parental
Control password for up to 40 discs. When
you set the 41st-disc, the first disc is canceled.
Press X/x to select “ON t,” then
press ENTER.
To turn off the Custom Parental Control
function
1
Follow steps 1 to 3 of “Custom Parental
Control.”
2
Press X/x to select “OFF t,” then press
ENTER.
3
Enter your 4-digit password using the
number buttons, then press ENTER.
STOP
DVD VIDEO
OFF
ON
PLAYER
PASSWORD
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
39US
To play a disc for which Custom Parental
Control is set
1
Insert the disc for which Custom Parental
Control is set.
The “CUSTOM PARENTAL
CONTROL” display appears.
CUSTOM PARENTAL CONTROL
Custom parental control is already
set. To play, enter your password
and press ENTER .
Parental Control (limited
playback)
Playback of some DVD VIDEOs can be
limited according to a predetermined level
such as the age of the users. The
“PARENTAL CONTROL” function allows
you to set a playback limitation level.
1
The Control Menu appears.
2
2
Press DISPLAY while the player is in
stop mode.
Enter your 4-digit password using the
number buttons, then press ENTER.
The player is ready for playback.
Press X/x to select
(PARENTAL CONTROL), then press
ENTER.
The options for “PARENTAL
CONTROL” appear.
12(27)
18(34)
T
1:32:55
z Hint
If you forget your password, enter the 6-digit
number “199703” using the number buttons when
the “CUSTOM PARENTAL CONTROL” display
asks you for your password, then press ENTER.
The display will ask you to enter a new 4-digit
password.
STOP
DVD VIDEO
OFF
ON
PLAYER
PASSWORD
3
Press X/x to select “PLAYER t,”
then press ENTER.
◆ If you have not entered a password
The display for registering a new
password appears.
Enter a 4-digit password using the
number buttons, then press ENTER.
The display for confirming the password
appears.
◆ When you have already registered a
password
The display for entering the password
appears.
4
Enter or re-enter your 4-digit password
using the number buttons, then press
ENTER.
The display for setting the playback
limitation level appears.
5
Press X/x to select “STANDARD,”
then press ENTER.
The selection items for “STANDARD”
are displayed.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
40
6
Press X/x to select a geographic area
as the playback limitation level, then
press ENTER.
The area is selected.
When you select “OTHERS t,” select
and enter a standard code in the table on
page 68 using the number buttons.
7
1
2
Parental Control setting is complete.
The lower the value, the stricter the
limitation.
To turn off the Parental Control function
The options for “PARENTAL
CONTROL” appear.
3
1
Insert the disc and press H.
The display for entering your password
appears.
2
Enter your 4-digit password using the
number buttons, then press ENTER.
The player starts playback.
Press X/x to select “PASSWORD
t,” then press ENTER.
The display for entering the password
appears.
4
Enter your 4-digit password using the
number buttons, then press ENTER.
5
Enter a new 4-digit password using the
number buttons, then press ENTER.
6
To confirm your password, re-enter it
using the number buttons, then press
ENTER.
Set “LEVEL” to “OFF” in step 8.
To play a disc for which Parental Control is
set
Press X/x to select
(PARENTAL CONTROL), then press
ENTER.
Playback
Select the level you want using X/x,
then press ENTER.
Press DISPLAY while the player is in
stop mode.
The Control Menu appears.
Press X/x to select “LEVEL,” then
press ENTER.
The selection items for “LEVEL” are
displayed.
8
Changing the password
If you make a mistake entering your
password
Press C before you press ENTER and input the
correct number.
z Hint
If you forget your password, remove the disc and
repeat steps 1 to 3 of “Parental Control (limited
playback).” When you are asked to enter your
password, enter “199703” using the number
buttons, then press ENTER. The display will ask
you to enter a new 4-digit password. After you enter
a new 4-digit password, replace the disc in the
player and press H. When the display for entering
your password appears, enter your new password.
Notes
• When you play discs which do not have the
Parental Control function, playback cannot be
limited on this player.
• Depending on the disc, you may be asked to
change the parental control level while playing
the disc. In this case, enter your password, then
change the level. If the Resume Play mode is
canceled, the level returns to the previous level.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
41US
Opposite direction
× 2b t 1m t 2m t 3m
Searching for a Scene
Searching for a
Particular Point on a
Disc (Scan, Slow-motion Play,
Freeze Frame)
You can quickly locate a particular point on a
disc by monitoring the picture or playing back
slowly.
STEP
STEP
3m (DVD/VIDEO CD only)
× 2b (DVD VIDEO only)
The “× 2B”/ “× 2b” playback speed is about
twice the normal speed.
The “3M”/“3m” playback speed is faster
than “2M”/“2m” and the “2M”/“2m”
playback speed is faster than “1M”/
“1m.”
Watching frame by frame
(Slow-motion Play)
Press
m or M
when the player is
in pause mode. To return to normal speed,
press H.
Each time you press
m or M
during Slow-motion Play, the playback speed
changes. Two speeds are available. With each
press the indication changes as follows:
Playback direction
y1
2
Notes
• Depending on the disc, you may not be able to do
some of the operations described.
• For DATA CDs/DATA DVDs, you can search for
a particular point only on an MP3 audio track.
Locating a point quickly by
playing a disc in fast forward or
fast reverse (Scan)
Press
m or M
while playing a
disc. When you find the point you want, press
H to return to normal speed. Each time you
press
m or M
during scan, the
scan speed changes. With each press the
indication changes as shown below. Actual
speeds may differ between discs.
Opposite direction (DVD only)
2
y1
The “2 y”/“2
than “1 y”/“1
Playing one frame at a time
(Freeze Frame)
When the player is in the pause mode, press
STEP to go to the next frame. Press
STEP to go to the preceding frame
(DVD only). To return to normal playback,
press H.
Note
You cannot search for a still picture in DVD-VR
mode.
Playback direction
× 2B t 1M t 2M t 3M
3M (DVD/VIDEO CD only)
× 2B (DVD VIDEO/CD only)
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
42
” playback speed is slower
.”
Searching for a Title/
Chapter/Track/Scene,
etc.
◆ When playing a VIDEO CD or Super VCD
without PBC Playback
TRACK
INDEX
◆ When playing a VIDEO CD or Super VCD
with PBC Playback
SCENE
◆ When playing a CD
TRACK
◆ When playing a DATA CD/DATA DVD
ALBUM
TRACK (MP3 audio tracks only)
FILE (JPEG image files only)
Example: when you select
CHAPTER
“** (**)” is selected (** refers to a number).
The number in parentheses indicates the total
number of titles, chapters, tracks, indexes,
scenes, albums, or files.
Number
buttons
CLEAR
ENTER
DISPLAY
12(27)
18(34)
T
1:32:55
Searching for a Scene
You can search a DVD by title or chapter, and
you can search a VIDEO CD/CD/DATA CD/
DATA DVD by track, index, file, or scene.
As titles and tracks are assigned unique
numbers on the disc, you can select the
desired one by entering its number. You can
also search for a scene using the time code.
PLAY
DVD VIDEO
Selected row
1 Press DISPLAY (When playing a
DATA CD or DATA DVD with JPEG
image files, press twice).
The Control Menu appears.
2 Press X/x to select the search
3 Press ENTER.
“** (**)” changes to “-- (**).”
12(27)
(34)
T
1:32:55
PLAY
DVD VIDEO
method.
◆ When playing a DVD
TITLE
CHAPTER
TIME/TEXT
Select “TIME/TEXT” to search for a starting
point by inputting the time code.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
43US
4 Press the number buttons to select
the title, chapter, track, index,
scene, etc., number you want to
search.
If you make a mistake
Cancel the number by pressing CLEAR,
then select another number.
Searching by Scene
(PICTURE NAVIGATION)
You can divide the screen into 9 subscreens
and find the desired scene quickly.
5 Press ENTER.
The player starts playback from the
selected number.
PICTURE
NAVI
To search for a scene using the time code
(DVD only)
1
In step 2, select
TIME/TEXT.
“T **:**:**” (playing time of the current
title) is selected.
2
Press ENTER.
“T **:**:**” changes to “T --:--:--.”
3
Input the time code using the number
buttons, then press ENTER.
For example, to find the scene at 2 hours,
10 minutes, and 20 seconds after the
beginning, just enter “2:10:20.”
z Hints
• When the Control Menu display is turned off, you
can search for a chapter (DVD) or track (CD/
DATA CD/DATA DVD) by pressing the number
buttons and ENTER.
• You can display the first scene of titles, chapters,
or tracks recorded on the disc on a screen divided
into 9 sections. You can start playback directly by
selecting one of the scenes. For details, see
“Searching by Scene (PICTURE
NAVIGATION)” (page 44).
Notes
• The title, chapter, or track number displayed is the
same number recorded on the disc.
• You cannot search for a scene on a DVD+RW/
DVD+R/DVD+R DL using the time code.
ENTER
RETURN
1 Press PICTURE NAVI during
playback.
The following display appears.
CHAPTER VIEWER
ENTER
2 Press PICTURE NAVI repeatedly to
select an item.
• CHAPTER VIEWER (DVD VIDEO
only): displays the first scene of each
chapter.
• TITLE VIEWER (DVD VIDEO only):
displays the first scene of each title.
• TRACK VIEWER (VIDEO CD/
Super VCD only): displays the first
scene of each track.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
44
DISPLAY
3 Press ENTER.
The first scene of each chapter, title, or
track appears as follows.
2
3
4
5
6
7
8
9
4 Press C/X/x/c to select a chapter,
title, or track, and press ENTER.
Playback starts from the selected scene.
Searching for a Scene
1
To return to normal play during setting
Press O RETURN or DISPLAY.
z Hint
If there are more than 9 chapters, titles, or tracks, V
is displayed at the bottom right of the screen.
To display the additional chapters, titles, or tracks,
select the bottom scenes and press x. To return to
the previous scene, select the top scenes and press
X.
Note
Depending on the disc, you may not be able to select
some items.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
45US
Sound Adjustments
Changing the Sound
When playing a DVD VIDEO recorded in
multiple audio formats (PCM, Dolby Digital,
or DTS), you can change the audio format. If
the DVD VIDEO is recorded with
multilingual tracks, you can also change the
language.
With CDs or VIDEO CDs, you can select the
sound from either the right or left channel and
listen to the sound of the selected channel
through both the right and left speakers. For
example, when playing a disc containing a
song with the vocals on the right channel and
the instruments on the left channel, you can
hear the instruments from both speakers by
selecting the left channel.
AUDIO
1 Press AUDIO during playback.
The following display appears.
1:ENGLISH DOLBY DIGITAL 3/2.1
2 Press AUDIO repeatedly to select
◆ When playing a DVD VIDEO
Depending on the DVD VIDEO, the
choice of language varies.
When 4 digits are displayed, they
indicate a language code. See “Language
Code List” on page 68 to see which
language the code represents. When the
same language is displayed two or more
times, the DVD VIDEO is recorded in
multiple audio formats.
◆ When playing in DVD-VR mode
The types of sound tracks recorded on a
disc are displayed. The default setting is
underlined.
Example:
• 1: MAIN (main sound)
• 1: SUB (sub sound)
• 1: MAIN+SUB (main and sub sound)
◆ When playing a VIDEO CD or CD
The default setting is underlined.
• STEREO: the standard stereo sound
• 1/L: the sound of the left channel
(monaural)
• 2/R: the sound of the right channel
(monaural)
◆ When playing a Super VCD
The default setting is underlined.
• 1:STEREO: the stereo sound of the
audio track 1
• 1:1/L: the sound of the left channel of
the audio track 1 (monaural)
• 1:2/R: the sound of the right channel of
the audio track 1 (monaural)
• 2:STEREO: the stereo sound of the
audio track 2
• 2:1/L: the sound of the left channel of
the audio track 2 (monaural)
• 2:2/R: the sound of the right channel of
the audio track 2 (monaural)
◆ When playing DATA CD or DATA DVD
The player’s internal background sound
will be played.
The default setting is underlined.
• BGM 1
• BGM 2
• BGM 3
• BGM 4
the desired audio signal.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
46
Notes
Note
• While playing a Super VCD on which the audio
track 2 is not recorded, no sound will come out
when you select “2:STEREO,” “2:1/L,” or
“2:2/R.”
• When playing in DVD-VR mode: If you connect
to an audio component using the DIGITAL OUT
(COAXIAL or OPTICAL)/HDMI OUT jack and
want to switch between the sound tracks, set
“DOLBY DIGITAL” to “D-PCM” in “AUDIO
SETUP” (page 62).
• If “MODE (MP3, JPEG)” is set to “AUTO” or
“AUTO (BGM)” (page 53), you can hear the
player’s internal background sound when MP3 is
not played.
If “DTS” is set to “OFF” in “AUDIO SETUP”
(page 62), the DTS track selection option will not
appear on the screen even if the disc contains DTS
tracks.
You can check the audio signal format by
pressing AUDIO repeatedly during playback.
The format of the current audio signal (Dolby
Digital, DTS, PCM, etc.) appears as shown
below.
Sound Adjustments
Checking the audio signal
format
Example:
Dolby Digital 5.1 ch
Rear (L/R)
1:ENGLISH DOLBY DIGITAL 3 / 2 .1
Front (L/R)
+ Center
LFE (Low Frequency
Effect)
About audio signals
Audio signals recorded in a disc contain the
sound elements (channels) shown below.
Each channel is output from a separate
speaker.
• Front (L)
• Front (R)
• Center
• Rear (L)
• Rear (R)
• Rear (Monaural): This signal can be either
the Dolby Surround Sound processed
signals or the Dolby Digital sound’s
monaural rear audio signals.
• LFE (Low Frequency Effect) signal
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
47US
To cancel the setting
TV Virtual Surround
Settings (TVS)
When you connect a stereo TV or 2 front
speakers, TVS (TV Virtual Surround) lets
you enjoy surround sound effects by using
sound imaging to create virtual rear speakers
from the sound of the front speakers (L: left,
R: right) without using actual rear speakers.
TVS was developed by Sony to produce
surround sound for home use using just a
stereo TV.
This only works when playing a multichannel
Dolby audio sound track. Furthermore, if the
player is set up to output the signal from the
DIGITAL OUT (OPTICAL or COAXIAL)/
HDMI OUT jack, the surround effect will
only be heard when “DOLBY DIGITAL” is
set to “D-PCM” in “AUDIO SETUP” (page
61).
SUR
1 Press SUR during playback.
The following display appears.
Select “OFF” in step 2.
◆TVS DYNAMIC THEATER, TVS DYNAMIC,
TVS WIDE
This mode is effective when the distance
between the front L and R speakers is short,
such as with built-in speakers on a stereo TV.
◆TVS NIGHT
This feature is useful when you want to hear
the dialog and enjoy the surround sound
effects of “TVS WIDE” at low volume.
◆TVS STANDARD
Use this setting when you want to use TVS
with 2 separate speakers.
Notes
• When the playing signal does not contain a signal
for the rear speakers, the surround effects cannot
be heard.
• When you select one of the TVS modes, turn off
the surround setting of the connected TV or audio
component.
• Make sure that your listening position is between
and at an equal distance from your speakers and
that the speakers are located in similar
surroundings.
• Not all discs will respond to the “TVS NIGHT”
function in the same way.
• If you use the DIGITAL OUT (OPTICAL or
COAXIAL)/HDMI OUT jack and set “DOLBY
DIGITAL” to “DOLBY DIGITAL,” and “DTS”
to “ON” in “AUDIO SETUP,” sound will come
from your speakers but it will not have the
SURROUND effect.
• The TVS effects do not work when using the Fast
Play or Slow Play functions, even though you can
change the TVS modes.
TVS DYNAMIC THEATER
2 Press SUR repeatedly to select
one of the TVS sounds.
See the explanations given for each item
in the following section.
• TVS DYNAMIC THEATER
• TVS DYNAMIC
• TVS WIDE
• TVS NIGHT
• TVS STANDARD
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
48
Enjoying MP3 Audio and JPEG
Images
About MP3 Audio Tracks
and JPEG Image Files
MP3 is audio compression technology that
satisfies the ISO/IEC MPEG regulations.
JPEG is image compression technology.
You can play DATA CDs/DATA DVDs that
contain MP3 audio tracks or JPEG image
files.
Notes
• The player will play any data with the extension
“.MP3,” “.JPG,” or “.JPEG,” even if they are not
in MP3 or JPEG format. Playing these data may
generate a loud noise which could damage your
speaker system.
• The player does not conform to audio tracks in
mp3PRO format.
• Some JPEG files cannot be played.
About playback order of albums,
tracks, and files
Albums play in the following order:
◆Structure of disc contents
Tree 1
Tree 2
Tree 3
Tree 4
Tree 5
ROOT
Enjoying MP3 Audio and JPEG Images
DATA CDs/DATA DVDs that the
player can play
You can play back DATA CDs or DATA
DVDs recorded in MP3 (MPEG-1 Audio
Layer III) and JPEG format.
However, this player only plays DATA CDs
whose logical format is ISO 9660 Level 1/
Level 2 or Joliet, and DATA DVDs of
Universal Disk Format (UDF).
Refer to the instructions supplied with the
disc drives and the recording software (not
supplied) for details on the recording format.
Note
The player may not be able to play some DATA
CDs/DATA DVDs created in the Packet Write
format.
MP3 audio track or JPEG image
file that the player can play
The player can play the following tracks and
files:
– MP3 audio tracks with the extension
“.MP3.”
– JPEG image files with the extension
“.JPEG” or “.JPG.”
– JPEG image files that conform to the DCF*
image file format.
* “Design rule for Camera File system”: Image
standards for digital cameras regulated by JEITA
(Japan Electronics and Information Technology
Industries Association).
Album
Track or file
When you insert a DATA CD/DATA DVD
and press H, the numbered tracks (or files)
are played sequentially, from 1 through 7.
Any sub-albums/tracks (or files) contained
within a currently selected album take
priority over the next album in the same tree.
(Example: C contains D so 4 is played
before 5.)
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
49US
When you press MENU and the list of album
names appears, the album names are arranged
in the following order:
A t B t C t D t F t G. Albums
that do not contain tracks (or files) (such as
album E) do not appear in the list.
z Hints
• If you add numbers (01, 02, 03, etc.) to the front
of the track/file names when you store the tracks
(or files) in a disc, the tracks and files will be
played in that order.
• Since a disc with many trees takes longer to start
playback, it is recommended that you create
albums with no more than two trees.
Notes
• Depending on the software you use to create the
DATA CD/DATA DVD, the playback order may
differ from the above illustration.
• The playback order above may not be applicable
if there are more than 200 albums and 300 tracks/
files in each album.
• The player can recognize up to 200 albums (the
player will count just albums, including albums
that do not contain MP3 audio tracks and JPEG
image files). The player will not play any albums
beyond the 200th album.
• Proceeding to the next or another album may take
some time.
Playing MP3 Audio
Tracks or JPEG Image
Files
You can play MP3 audio tracks and JPEG
image files on DATA CDs or DATA DVDs.
CLEAR
PICTURE
NAVI
MENU
ENTER
RETURN
ZOOM
SUBTITLE
z Hint
You can view the disc information while playing
MP3 audio tracks (page 30).
Notes
• DATA CDs recorded in KODAK Picture CD
format automatically start playing when inserted.
• If no MP3 audio track or JPEG image file is
recorded on the DATA CD/DATA DVD, “No
audio data” or “No image data” appears on the
screen.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
50
Selecting an album
1
Press MENU.
The list of albums on the disc appears.
When an album is being played, its title is
shaded.
2
Press X/x to select the album you
want to play.
3
Press H.
Playback starts from the selected album.
To select MP3 audio tracks, see
“Selecting an MP3 audio track”
(page 51).
To select JPEG image files, see
“Selecting a JPEG image file” (page 51).
To go to the next or previous MP3 audio
track
Press > or . during playback. You can
select the first track of the next album by
pressing > during playback of the last
track of the current album.
Note that you cannot return to the previous
album by using . and that you need to
select the previous album from the album list.
Selecting a JPEG image file
1
After step 2 of “Selecting an album,”
press PICTURE NAVI.
To stop playback
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Press x.
To go to the next or previous page
Press c or C.
To turn on or off the display
Press MENU repeatedly.
z Hint
Of the selected album, you can select to play only
the MP3 audio tracks, JPEG image files, or both, by
setting “MODE (MP3, JPEG)” (page 53).
Selecting an MP3 audio track
1
After step 2 of “Selecting an album,”
press ENTER.
The list of tracks in the album appears.
2
Press X/x to select a track and press
ENTER.
Playback starts from the selected track.
To stop playback
Press x.
To go to the next or previous page
To display additional images, select a
bottom image and press x. To return to a
previous image, select a top image and
press X.
2
Enjoying MP3 Audio and JPEG Images
The image files in the album appear in 16
subscreens. A scroll box is displayed on
the right.
Press C/X/x/c to select the image you
want to view, and press ENTER.
The selected image appears.
To go to the next or previous JPEG image
file
Press C or c during playback. You can select
the first file of the next album by pressing c
during playback of the last file of the current
album.
Note that you cannot return to the previous
album by using C and that you need to select
the previous album from the album list.
To rotate a JPEG image
Press X/x while viewing the image. Each
time you press X, the image rotates
counterclockwise by 90 degrees.
To return to the previous display
To return to normal view, press CLEAR.
Press O RETURN.
Note that the view also returns to normal if
you press C/c to go to the next or previous
image.
Downloaded From DvDPlayer-Manual.com Sherwood
Manuals
Press c or C.
,continued
51US
To magnify a JPEG image (ZOOM)
Press ZOOM while viewing the image. You
can enlarge the image up to four times the
original size and scroll using C/X/x/c.
To return to normal view, press CLEAR.
◆When pressed once (x2)
The image enlarges twice the original size.
◆When pressed twice (x4)
The image enlarges four times the original
size.
Enjoying JPEG Images as
a Slide Show
You can play JPEG image files on a DATA
CD or DATA DVD successively as a slide
show.
To display JPEG image information
Press SUBTITLE while viewing JPEG
image files.
The file name, camera maker/model, date,
time, picture resolution, file size, camera
setting information (ISO speed rating,
Exposure time, F Number, Exposure bias, or
Focal length) of the picture are displayed on
the screen.
is displayed when the picture was taken
using flash.
is displayed when the image is
automatically rotated.
To hide the information, press SUBTITLE.
Note that the above information may not
appear depending on the digital camera.
To stop viewing the JPEG image
Press x.
z Hints
• While viewing JPEG image files, you can set
options such as “INTERVAL” (page 54),
“EFFECT” (page 54) and “SHARPNESS”
(page 37).
• You can view JPEG images files without MP3
audio by setting “MODE (MP3, JPEG)” to
“IMAGE (JPEG)” (page 53).
• The date the picture was taken is displayed beside
“DATE” in the Control Menu (page 13). Note that
no date may appear depending on the digital
camera.
Note
PICTURE NAVI does not work if “AUDIO (MP3)”
is selected in “MODE (MP3, JPEG)” (page 53).
MENU
ENTER
DISPLAY
AUDIO
1 Press MENU.
The list of albums on the DATA CD/
DATA DVD appears.
2 Press X/x to select an album.
3 Press H.
The JPEG images in the selected album
start playing as a slide show.
To stop playback
Press x.
Notes
• The slide show stops when X/x or ZOOM is
pressed.To resume the slide show, press H.
• This function does not work if “MODE (MP3,
JPEG)” is set to “AUDIO (MP3)” (page 53).
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
52
Viewing a slide show with sound
(MODE (MP3, JPEG))
You can enjoy a slide show with sound.
1
Press DISPLAY during stop mode.
The Control Menu appears.
2
Press X/x to select
(MODE
(MP3, JPEG)) and press ENTER.
The options for “MODE (MP3, JPEG)”
appear.
3
DATA CD MP3
Press X/x to select “AUTO” (default),
and press ENTER.
The default setting is underlined.
• AUTO: plays the JPEG image files with
MP3 audio tracks. If there is no MP3
file, plays JPEG image files with the
player’s internal background sound.
• AUTO (BGM): plays the JPEG image
files with the player’s internal
background sound. To choose the
melody of the background sound, press
AUDIO repeatedly while viewing the
image. You can enjoy MP3 audio track
whenever MP3 track is selected.
• AUDIO (MP3): plays only MP3 audio
tracks continuously.
• IMAGE (JPEG): plays only JPEG
image files continuously.
4
Notes
• If you play a disc containing MP3 audio tracks
only and “MODE (MP3, JPEG)” is set to
“AUTO” or “AUTO (BGM)”, you can listen to
MP3 audio tracks only.
• If you play a disc containing JPEG image files
only, the player’s internal background sound will
be played when “MODE (MP3, JPEG)” is set to
“AUTO” or “AUTO (BGM)”.
• If JPEG playback finishes during MP3 playback,
MP3 playback continues with background
picture.
• If MP3 playback finishes during JPEG playback,
player’s internal background sound starts.
• If you play large MP3 track data and JPEG image
data at the same time, the sound may skip. It is
recommended that you set the MP3 bit rate to 128
kbps or lower when creating the file. If the sound
still skips, then reduce the size of the JPEG file.
Enjoying MP3 Audio and JPEG Images
12(27)
18(34)
T
32:55
AUTO
AUTO
AUTO (BGM)
AUDIO (MP3)
IMAGE (JPEG)
z Hints
• To repeat both MP3 audio tracks and JPEG image
files in a single album, repeat the same MP3 audio
track or album when “MODE (MP3, JPEG)” is set
to “AUTO” or “AUTO (BGM)”. See “Playing
repeatedly (Repeat Play)” (page 34) to repeat the
track or album.
• The player recognizes a maximum of 200 albums
regardless of the selected mode. Of each album,
the player recognizes up to 300 MP3 audio tracks
and 300 JPEG image files when “AUTO” or
“AUTO (BGM)” is selected, 600 MP3 audio
tracks when “AUDIO (MP3)” is selected, 600
JPEG image files when “IMAGE (JPEG)” is
selected.
Press MENU.
The list of albums on the DATA CD/
DATA DVD appears.
5
Press X/x to select the album that
contains both the MP3 audio tracks
and JPEG images you want to play.
6
Press H.
A slide show starts with sound.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
53US
Setting the pace for a slide show
(INTERVAL)
Selecting the slides’ appearance
(EFFECT)
You can set the time the slides are displayed
on the screen.
You can select the way the slides are
displayed during a slide show.
1
1
Press DISPLAY twice while viewing a
JPEG image or when the player is in
stop mode.
2
Press X/x to select
then press ENTER.
Press DISPLAY twice while viewing a
JPEG image or when the player is in
stop mode.
The Control Menu appears.
2
Press X/x to select
(INTERVAL), then press ENTER.
(EFFECT),
The options for “EFFECT” appear.
The options for “INTERVAL” appear.
3 ( 1 2)
4)
1(
10/29/2007
NORMAL
NORMAL
FAST
SLOW 1
SLOW 2
DATA CD JPEG
INTERVAL
3
3 ( 1 2)
4)
1(
10/29/2007
Press X/x to select a setting.
MODE 1
MODE 1
MODE 2
MODE 3
MODE 4
MODE 5
OFF
3
Press ENTER.
Notes
• Some JPEG files, especially progressive JPEG
files or JPEG files of 3,000,000 pixels or more,
may take longer to display than others, which may
make the duration seem longer than the setting
you selected.
• Duration of interval depends on “JPEG
RESOLUTION” setting in “SCREEN SETUP”
(page 57).
Press X/x to select a setting.
The default setting is underlined.
• MODE 1: the images randomly cycle
through the effects.
• MODE 2: the next image slides over the
previous image.
• MODE 3: the image sweeps in from top
to bottom.
• MODE 4: the image sweeps in from left
to right.
• MODE 5: the image stretches out from
the center of the screen.
• OFF: turns off this function.
The default setting is underlined.
• NORMAL: sets to standard duration.
• FAST: sets a duration shorter than
NORMAL.
• SLOW 1: sets a duration longer than
NORMAL.
• SLOW 2: sets a duration longer than
SLOW 1.
4
4
Press ENTER.
Note
Note that this setting does not work if the JPEG file
has rotation information.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
54
DATA CD JPEG
3 Press X/x to select “CUSTOM,”
Settings and Adjustments
Using the Setup Display
By using the Setup Display, you can make
various adjustments to items such as picture
and sound. You can also set a language for the
subtitles and the Setup Display, among other
things.
For details on each Setup Display item, see
pages from 56 to 62.
Note
Playback settings stored in the disc take priority
over the Setup Display settings and not all of the
functions described may work.
then press ENTER.
The Setup Display appears.
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
ENGLISH
ENGLISH
ORIGINAL
ENGLISH
4 Press X/x to select the setup item
The Setup item is selected.
Example: “SCREEN SETUP”
Number
buttons
Selected item
ENTER
DISPLAY
SCREEN SETUP
TV TYPE:
16:9
HDMI RESOLUTION:
AUTO (1920×1080p)
JPEG RESOLUTION:
HD
YCBCR/RGB (HDMI):
YCBCR
SCREEN SAVER:
ON
BACKGROUND:
JACKET PICTURE
ON
BLACK LEVEL:
OFF
BLACK LEVEL (COMPONENT OUT):
FULL
4:3 OUTPUT:
Settings and Adjustments
from the displayed list:
“LANGUAGE SETUP,” “SCREEN
SETUP,” “CUSTOM SETUP,” or
“AUDIO SETUP.” Then press
ENTER.
Setup items
X/x to select an item, then
1 Press DISPLAY when the player is 5 Press
press ENTER.
in stop mode.
The options for the selected item appear.
Example: “TV TYPE”
The Control Menu appears.
2 Press X/x to select
(SETUP), then press ENTER.
The options for “SETUP” appear.
( 47 )
STOP
DVD VIDEO
SCREEN SETUP
16:9
TV TYPE:
16:9
HDMI RESOLUTION:
JPEG RESOLUTION: 4:3 LETTER BOX
YCBCR/RGB (HDMI):
4:3 PAN SCAN
SCREEN SAVER:
ON
BACKGROUND:
JACKET PICTURE
BLACK LEVEL:
ON
OFF
BLACK LEVEL (COMPONENT OUT):
FULL
4:3 OUTPUT:
QUICK
CUSTOM
RESET
QUICK
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
Options
,continued
55US
6 Press X/x to select a setting, then
press ENTER.
The setting is selected and setup is
complete.
Example: “4:3 PAN SCAN”
Selected setting
SCREEN SETUP
TV TYPE:
4:3 PAN SCAN
HDMI RESOLUTION:
AUTO (1920×1080p)
HD
JPEG RESOLUTION:
YCBCR/RGB (HDMI):
YCBCR
SCREEN SAVER:
ON
BACKGROUND:
JACKET PICTURE
BLACK LEVEL:
ON
OFF
BLACK LEVEL (COMPONENT OUT):
FULL
4:3 OUTPUT:
Setting the Display or
Sound Track Language
(LANGUAGE SETUP)
“LANGUAGE SETUP” allows you to set
various languages for the on-screen display or
sound track.
Select “LANGUAGE SETUP” in the Setup
Display. To use the display, see “Using the
Setup Display” (page 55).
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
To enter the Quick Setup mode
ENGLISH
ENGLISH
ORIGINAL
ENGLISH
Select “QUICK” in step 3. Follow from step
5 of the Quick Setup explanation to make
basic adjustments (page 24).
To reset all of the “SETUP” settings
1
Select “RESET” in step 3 and press
ENTER.
2
Select “YES” using X/x.
You can also quit the process and return
to the Control Menu by selecting “NO”
here.
3
Press ENTER.
All the settings explained on pages 56 to
62 return to the default settings. Do not
press [/1 while resetting the player,
which takes a few seconds to complete.
◆ OSD (On-Screen Display)
Switches the display language on the screen.
◆ MENU (DVD VIDEO only)
You can select the desired language for the
disc’s menu.
◆ AUDIO (DVD VIDEO only)
Switches the language of the sound track.
When you select “ORIGINAL,” the language
given priority in the disc is selected.
◆ SUBTITLE (DVD VIDEO only)
Switches the language of the subtitle recorded
on the DVD VIDEO.
When you select “AUDIO FOLLOW,” the
language for the subtitles changes according
to the language you selected for the sound
track.
z Hint
If you select “OTHERS t” in “MENU,”
“SUBTITLE,” or “AUDIO,” select and enter a
language code from “Language Code List” on
page 68 using the number buttons.
Note
If you select a language in “MENU,”
“SUBTITLE,” or “AUDIO” that is not recorded on
a DVD VIDEO, one of the recorded languages will
be automatically selected.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
56
Settings for the Display
(SCREEN SETUP)
Choose settings according to the TV to be
connected.
Select “SCREEN SETUP” in the Setup
Display. To use the display, see “Using the
Setup Display” (page 55).
The default settings are underlined.
SCREEN SETUP
TV TYPE:
HDMI RESOLUTION:
JPEG RESOLUTION:
16:9
AUTO (1920×1080p)
HD
YCBCR/RGB (HDMI):
YCBCR
ON
JACKET PICTURE
BLACK LEVEL:
ON
BLACK LEVEL (COMPONENT OUT):
OFF
4:3 OUTPUT:
FULL
SCREEN SAVER:
BACKGROUND:
Selects the aspect ratio of the connected TV
(4:3 standard or wide).
16:9
4:3
LETTER
BOX
Select this when you connect a
wide-screen TV or a TV with a
wide mode function.
Select this when you connect a
4:3 screen TV. Displays a wide
picture with bands on the upper
and lower portions of the
screen.
4:3
Select this when you connect a
PAN SCAN 4:3 screen TV. Automatically
displays the wide picture on the
entire screen and cuts off the
portions that do not fit.
16:9
4:3 LETTER BOX
4:3 PAN SCAN
◆ HDMI RESOLUTION
Selects the type of video signals output from
the HDMI OUT jack. When you select
AUTO (1920× 1080p) (default), the player
outputs video signals of the highest resolution
acceptable for your TV. If the picture is not
clear, natural or to your satisfaction, try
another option that suits the disc and your
TV/projector, etc. For details, refer also to the
instruction manual supplied with the TV/
projector, etc.
AUTO
Normally, select this.
(1920× 1080p)
1920× 1080i
Sends 1920× 1080i video
signals.
1280× 720p
Sends 1280× 720p video
signals.
720× 480p
Sends 720× 480p video signals.
To reset the setting
If the picture does not appear normal or goes
blank, press [/1 to turn off the player, and
enter “369” using the number buttons on the
remote, then press [/1 to turn on the player
again.
Settings and Adjustments
◆ TV TYPE
Note
Depending on the DVD, “4:3 LETTER BOX” may
be selected automatically instead of “4:3 PAN
SCAN” or vice versa.
Notes
• In case of “AUTO (1920× 1080p),” the player
automatically adjusts the video signals that are
suitable for the TV.
Other cases, the player directly send the signal
even if TV cannot accept.
• When the HDMI indicator on the front panel
lights up, images from the S VIDEO OUT and
LINE OUT (VIDEO) jacks are enlarged
vertically. (Except when 720× 480p is selected).
◆ JPEG RESOLUTION
Selects the type of JPEG resolution so that
you can enjoy high picture quality via your
HDMI connection.
You cannot select this when “HDMI
RESOLUTION” is set to “720× 480p” or
“TV TYPE” is set to “4:3 LETTER BOX” or
“4:3 PAN SCAN”.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
57US
SD
Displays standard definition
picture with black frame.
HD
Displays high definition picture
with black frame.
HD
Displays high definition picture
without black frame.
(1920× 1080i) Displays high definition picture
HD
with black frame at 1920× 1080
pixels.
(1920× 1080i) Displays high definition picture
HD
without black frame at
1920× 1080 pixels.
Notes
• To view the best picture quality, set this setting to
“(1920× 1080i) HD ” or “(1920× 1080i) HD.”
• “(1920× 1080i) HD ” and “(1920× 1080i) HD”
are effective only when you set “HDMI
RESOLUTION” to “1920x1080i” and “TV
TYPE” to “16:9.”
• If you set this setting to “(1920× 1080i) HD ”
or “(1920× 1080i) HD,” wipe, rotation, and zoom
function are not available.
• If you want to use wipe, rotation, and zoom
function; sets this setting to “SD,” “HD ,” or
“HD.”
• If you set this setting to “(1920× 1080i) HD ”
or “(1920× 1080i) HD,” next image appears after
black mute.
• HDMI signal will stop momentarily during
loading or unloading DATA CD or DATA DVD
disc.
◆ YCBCR/RGB (HDMI)
Selects the type of HDMI signal output from
HDMI OUT jack.
YCBCR
Outputs YCBCR signals.
RGB
Outputs RGB signals.
◆ SCREEN SAVER
The screen saver image appears when you
leave the player in pause or stop mode for 15
minutes, or when you play a CD or DATA
CD (MP3 audio)/DATA DVD (MP3 audio)
for more than 15 minutes. The screen saver
will help prevent your display device from
becoming damaged (ghosting). Press H to
turn off the screen saver.
ON
Turns on the screen saver.
OFF
Turns off the screen saver.
◆ BACKGROUND
Selects the background color or picture on the
TV screen when the player is in stop mode or
while playing a CD or DATA CD (MP3
audio)/DATA DVD (MP3 audio).
JACKET
PICTURE
GRAPHICS A preset picture stored in the
player appears.
BLUE
The background color is blue.
BLACK
The background color is black.
◆ BLACK LEVEL
Selects the black level (setup level) for the
video signals output from the jacks other than
COMPONENT VIDEO OUT/HDMI OUT.
ON
Sets the black level of the
output signal to the standard
level.
OFF
Lowers the standard black
level. Use this when the picture
becomes too white.
Notes
• If the playback picture becomes distorted, set
“YCBCR” to “RGB.”
• If the HDMI OUT jack is connected to equipment
with a DVI jack, “RGB” signals will be
automatically output even when you select
“YCBCR”.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
58
The jacket picture (still picture)
appears, but only when the
jacket picture is already
recorded on the disc (CDEXTRA, etc.). If the disc does
not contain a jacket picture, the
“GRAPHICS” picture appears.
◆ BLACK LEVEL (COMPONENT OUT)
Selects the black level (setup level) for the
video signals output from the COMPONENT
VIDEO OUT jacks. You cannot select this
when the player outputs progressive signals
(page 19).
OFF
ON
Sets the black level of the
output signal to the standard
level. Normally, select this
position.
Raises the standard black level.
Use this setting when the
picture appears too dark.
Custom Settings (CUSTOM
SETUP)
Use this to set up playback related and other
settings.
Select “CUSTOM SETUP” in the Setup
Display. To use the display, see “Using the
Setup Display” (page 55).
The default settings are underlined.
CUSTOM SETUP
AUTO POWER OFF:
AUTO PLAY:
DIMMER:
PAUSE MODE:
TRACK SELECTION:
MULTI-DISC RESUME:
HDMI CONTROL:
LANGUAGE FOLLOW:
◆ 4:3 OUTPUT
FULL
NORMAL
Select this when you can
change the aspect ratio on your
TV.
Select this when you cannot
change the aspect ratio on your
TV. Shows a 16:9 aspect ratio
signal with black bands on left
and right sides of the image.
◆ AUTO POWER OFF
Switches the Auto Power Off setting on or
off.
OFF
Switches this function off.
ON
The player enters standby mode
when left in stop mode for more
than 30 minutes.
Settings and Adjustments
This setting is effective only when you set
“TV TYPE” in “SCREEN SETUP” to
“16:9.”
Adjust this to watch 4:3 aspect ratio. If you
can change the aspect ratio on your TV,
change the setting on your TV, not the player.
OFF
OFF
BRIGHT
AUTO
OFF
ON
OFF
ON
◆ AUTO PLAY
Switches the Auto Play setting on or off. This
function is useful when the player is
connected to a timer (not supplied).
16:9 aspect ratio TV
OFF
Switches this function off.
ON
Automatically starts playback
when the player is turned on by
a timer (not supplied).
◆ DIMMER
Adjusts the lighting of the front panel display.
BRIGHT
Makes the lighting bright.
DARK
Makes the lighting dark.
AUTO
DARK
Makes the lighting dark if you
do not operate the player or
remote for a short while.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
59US
◆ PAUSE MODE (DVDs only)
◆ HDMI CONTROL
Selects the picture in pause mode.
Switches the HDMI CONTROL setting
on or off.
AUTO
FRAME
The picture, including subjects
that move dynamically, is
output with no jitter. Normally,
select this position.
The picture, including subjects
that do not move dynamically,
is output in high resolution.
◆ TRACK SELECTION (DVD VIDEO only)
Gives the sound track which contains the
highest number of channels priority when you
play a DVD VIDEO on which multiple audio
formats (PCM, DTS, or Dolby Digital
format) are recorded.
OFF
No priority given.
AUTO
Priority given.
OFF
Switches this function off.
ON
Allows you to use the HDMI
CONTROL features (page 19).
◆ LANGUAGE FOLLOW
Switches the languages of the DVD player
to the same as the current TV OSD
language.
You cannot select this when “HDMI
CONTROL” is set to “OFF.”
ON
Switches this function on.
OFF
Switches this function off.
Notes
• Turn off any display before using this function.
• The OSD language for player keeps if the TV’s
language cannot be supported.
Notes
• When you set the item to “AUTO,” the language
may change. The “TRACK SELECTION” setting
has higher priority than the “AUDIO” settings in
“LANGUAGE SETUP” (page 56).
• If you set “DTS” to “OFF” (page 62), the DTS
sound track is not played even if you set “TRACK
SELECTION” to “AUTO.”
• If PCM, DTS, and Dolby Digital sound tracks
have the same number of channels, the player
selects PCM, DTS, and Dolby Digital sound
tracks in this order.
◆ MULTI-DISC RESUME (DVD VIDEO/
VIDEO CD only)
Switches the Multi-disc Resume setting on or
off. Resume playback can be stored in
memory for up to 6 different DVD VIDEOs/
VIDEO CDs (page 28).
ON
Stores the resume setting in
memory for up to 6 discs.
OFF
Does not store the resume
setting in memory. Playback
restarts at the resume point only
for the current disc in the player.
Note
If you run Quick Setup, Multi-disc Resume settings
stored in memory may return to the default settings.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
60
Settings for the Sound
(AUDIO SETUP)
“AUDIO SETUP” allows you to set the sound
according to the playback and connection
conditions.
Select “AUDIO SETUP” in the Setup
Display. To use the display, see “Using the
Setup Display” (page 55).
The default settings are underlined.
AUDIO SETUP
AUDIO DRC:
STANDARD
DOWNMIX:
DOLBY SURROUND
DIGITAL OUT:
ON
D-PCM
DOLBY DIGITAL:
DTS:
OFF
48kHz/16bit
48kHz/96kHz PCM:
AUDIO (HDMI):
AUTO
DOLBY
SURROUND
Normally, select this position.
Multi-channel audio signals are
output to 2 channels for enjoying
surround sounds.
NORMAL
Multi-channel audio signals are
downmixed to 2 channels for use
with your stereo.
◆ DIGITAL OUT
Selects if audio signals are output via the
DIGITAL OUT (OPTICAL or COAXIAL)/
HDMI OUT jack.
Normally, select this position.
When you select “ON,” see
“Setting the digital output signal”
for further settings.
OFF
The influence of the digital
circuit upon the analog circuit is
minimal. If you are using the
HDMI OUT jack, PCM sound
will be output depending on the
connected equipment.
If the signal is encrypted for
copyright protection purposes,
the signal is only output as
48 kHz/16 bit PCM.
◆ AUDIO DRC (Dynamic Range Control)
(DVDs only)
Makes the sound clear when the volume is
turned down when playing a DVD that
conforms to “AUDIO DRC.”
This function affects the output from the
following jacks:
– LINE OUT L/R (AUDIO) jacks
– DIGITAL OUT (OPTICAL or COAXIAL)/
HDMI OUT jack only when “DOLBY
DIGITAL” is set to “D-PCM” (page 62).
STANDARD Normally, select this position.
TV MODE
Makes low sounds clear even if
you turn the volume down.
WIDE
RANGE
Gives you the feeling of being
at a live performance.
◆ DOWNMIX (DVDs only)
Switches the method for mixing down to 2
channels when you play a DVD which has
rear sound elements (channels) or is recorded
in Dolby Digital format. For details on the
rear signal components, see “Checking the
audio signal format” (page 47). This function
affects the output of the following jacks:
– LINE OUT L/R (AUDIO) jacks
– DIGITAL OUT (OPTICAL or COAXIAL)/
HDMI OUT jack when “DOLBY
DIGITAL” is set to “D-PCM” (page 62).
Setting the digital output signal
Settings and Adjustments
ON
Switches the method of outputting audio
signals when you connect a component such
as an audio component or MD deck with a
digital input jack.
For connection details, see page 20.
Select “DOLBY DIGITAL,” “DTS,” and
“48kHz/96kHz PCM” after setting
“DIGITAL OUT” to “ON.”
If you connect a component that is
incompatible with the selected audio signal, a
loud noise (or no sound) may be heard from
the speakers, risking damage to your ears or
speakers.
Notes
• The AV SYNC function (page 38) is not effective
if you use the DIGITAL OUT (OPTICAL or
COAXIAL) jack, and set “DOLBY DIGITAL” or
“DTS” to “DOLBY DIGITAL” or “ON”
respectively.
• The AV SYNC function (page 38) is not effective
if you connect a Dolby Digital or DTS-compliant
device via the HDMI OUT jack, and set “DOLBY
DIGITAL” or “DTS” to “DOLBY DIGITAL” or
“ON” respectively.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
61US
◆ DOLBY DIGITAL (DVDs only)
◆ 48kHz/96kHz PCM (DVD VIDEO only)
Selects the type of Dolby Digital signal.
Selects the sampling frequency of the audio
signal.
D-PCM
DOLBY
DIGITAL
Select this when the player is
connected to an audio
component without a built-in
Dolby Digital decoder. You can
select whether the signals
conform to Dolby Surround
(Pro Logic) or not by making
adjustments to the
“DOWNMIX” item in
“AUDIO SETUP” (page 61).
Select this when the player is
connected to an audio
component with a built-in
Dolby Digital decoder.
Note
If the HDMI OUT jack is connected to equipment
not compatible with DOLBY DIGITAL signals, the
“D-PCM” signals will be automatically output even
when you select “DOLBY DIGITAL.”
◆ DTS
48kHz/16bit The audio signals of DVD
VIDEOs are always converted
to 48kHz/16bit.
96kHz/24bit All types of signals including
96kHz/24bit are output in their
original format. However, if the
signal is encrypted for
copyright protection purposes,
the signal is only output as
48kHz/16bit.
Notes
• The analog audio signals from the LINE OUT
L/R (AUDIO) jacks are not affected by this
setting and keep their original sampling frequency
level.
• If the HDMI OUT jack is connected to equipment
not compatible with 96 kHz/24 bit signals,
48 kHz/16 bit PCM will be automatically output
even when you select “96kHz/24bit.”
Select the type of DTS audio signals.
◆ AUDIO (HDMI)
OFF
Selects the type of audio signal output from
the HDMI OUT jack.
ON
Select this when the player is
connected to an audio
component without a built-in
DTS decoder.
Select this when the player is
connected to an audio
component with a built-in DTS
decoder.
AUTO
Normally, select this. Outputs
audio signals according to the
“DIGITAL OUT” settings
(page 61).
PCM
Converts Dolby Digital, or
96 kHz/24 bit PCM signals to
48 kHz/16 bit PCM.
Note
If the HDMI OUT jack is connected to equipment
not compatible with DTS signals, the “OFF” signals
will be automatically output even when you select
“ON.”
Note
A loud noise (or no sound) will be output if you
connect the player to a TV that is not compatible
with DOLBY DIGITAL/DTS signals and “AUTO”
is selected. In this case, select “PCM.”
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
62
Additional Information
Troubleshooting
If you experience any of the following
difficulties while using the player, use this
troubleshooting guide to help remedy the
problem before requesting repairs. Should
any problem persist, consult your nearest
Sony dealer.
Power
, If the HDMI OUT jack is used for video
output, changing the “HDMI
RESOLUTION” setting in “SCREEN
SETUP” may solve the problem (page 57).
Connect the TV and the player using a video
jack other than the HDMI OUT, and switch
the TV’s input to the connected video input
so that you can see the on-screen displays.
Change the “HDMI RESOLUTION”
setting in “SCREEN SETUP,” and switch
the TV’s input back to HDMI. If the picture
still does not appear, repeat the steps and try
other options.
, Press [/1 to turn off the player, and enter
“369” using the number buttons on the
remote, then press [/1 to turn on the player
again (page 57).
The power is not turned on.
, Check that the power cord is connected
securely.
Picture
There is no picture/picture noise appears.
, Try the following: 1Turn the player off
and on again. 2Turn the connected
equipment off and on again. 3Disconnect
and then connect the HDMI cord again.
The picture does not fill the screen, even
though the aspect ratio is set in “TV TYPE”
under “SCREEN SETUP.”
, The aspect ratio of the disc is fixed on your
DVD.
Additional Information
, Re-connect the connecting cord securely.
, The connecting cords are damaged.
, Check the connection to your TV (page 17)
and switch the input selector on your TV so
that the signal from the player appears on
the TV screen.
, The disc is dirty or flawed.
, If the picture output from your player goes
through your VCR to get to your TV or if
you are connected to a combination TV/
VIDEO player, the copy-protection signal
applied to some DVD programs could affect
picture quality. If you still experience
problems even when you connect your
player directly to your TV, try connecting
your player to your TV’s S VIDEO input
(page 17).
, You have selected “PROGRESSIVE
AUTO” or “PROGRESSIVE VIDEO” using
the PROGRESSIVE button on the front
panel even though your TV cannot accept the
progressive signal.
, Even if your TV is compatible with
progressive format 480p signals, the image
may be affected when you set the player to
progressive format. In this case, select
“NORMAL (INTERLACE)” using the
PROGRESSIVE button on the front panel
so that the player is set to normal (interlace)
format.
, The player is connected to an input device
that is not HDCP compliant (the HDMI
indicator on the front panel does not light
up). See page 18.
There is no picture or the picture noise
appears when connected to the HDMI OUT
jack.
Sound
There is no sound.
, Re-connect the connecting cord securely.
, The connecting cord is damaged.
, The player is connected to the wrong input
jack on the audio component (page 20).
, The audio component input is not correctly
set.
, The player is in pause mode or in Slowmotion Play mode.
, The player is in fast forward or fast reverse
mode.
, If the audio signal does not come through
the DIGITAL OUT (OPTICAL or
COAXIAL)/HDMI OUT jack, check the
audio settings (page 61).
, While playing a Super VCD on which the
audio track 2 is not recorded, no sound will
come out when you select “2:STEREO,”
“2:1/L,” or “2:2/R.”
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
63US
, The equipment connected to the HDMI
OUT jack does not conform to the audio
signal format, in this case set
“AUDIO(HDMI)” in “AUDIO SETUP” to
“PCM” (page 62).
No sound is output from the HDMI OUT
jack
, Try the following: 1Turn the player off
and on again. 2Turn the connected
equipment off and on again. 3Disconnect
and then connect the HDMI cord again.
, The HDMI OUT jack is connected to a DVI
device (DVI jacks do not accept audio
signals).
The sound volume is low.
, The sound volume is low on some DVDs.
The sound volume may improve if you set
“AUDIO DRC” in “AUDIO SETUP” to
“TV MODE” (page 61).
Operation
The remote does not function.
, The batteries in the remote are weak.
, There are obstacles between the remote and
the player.
, The distance between the remote and the
player is too far.
, The remote is not pointed at the remote
sensor on the player.
The disc does not play.
, The disc is turned over.
, Insert the disc with the playback side facing
down.
, The disc is skewed.
, The player cannot play certain discs
(page 8).
, The region code on the DVD does not match
the player.
, Moisture has condensed inside the player
(page 5).
, The player cannot play a recorded disc that
is not correctly finalized (page 9).
The MP3 audio track cannot be played
(page 49).
, The DATA CD is not recorded in MP3
format that conforms to ISO 9660 Level 1/
Level 2 or Joliet.
, The DATA DVD is not recorded in MP3
format that conforms to UDF (Universal
Disk Format).
, The MP3 audio track does not have the
extension “.MP3.”
, The data is not formatted in MP3 even
though it has the extension “.MP3.”
, The data is not MPEG-1 Audio Layer III
data.
, The player cannot play audio tracks in
mp3PRO format.
, “MODE (MP3, JPEG)” is set to “IMAGE
(JPEG)” (page 53).
The JPEG image file cannot be played
(page 49).
, The DATA CD is not recorded in JPEG
format that conforms to ISO 9660 Level 1/
Level 2, or Joliet.
, The DATA DVD is not recorded in JPEG
format that conforms to UDF (Universal
Disk Format).
, The file has an extension other than
“.JPEG” or “.JPG.”
, The image is larger than 3072 (width) ×
2048 (height) in normal mode, or more than
3,300,000 pixels in progressive JPEG.
(Some progressive JPEG files cannot be
displayed even if the file size is within this
specified capacity.)
, The image does not fit the screen (the image
is reduced).
, “MODE (MP3, JPEG)” is set to “AUDIO
(MP3)” (page 53).
The MP3 audio tracks and JPEG image
files start playing simultaneously.
, “MODE (MP3, JPEG)” is set to “AUTO”
(page 53).
The player’s internal background sound
and JPEG image files start playing
simultaneously.
, “MODE (MP3, JPEG)” is set to “AUTO
(BGM)” (page 53).
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
64
The album/track/file names are not
displayed correctly.
, The player can only display numbers and
alphabet. Other characters are displayed as
“*”.
The disc does not start playing from the
beginning.
, Program Play, Shuffle Play, Repeat Play, or
A-B Repeat Play is selected (page 32).
, Resume play has taken effect (page 28).
The player starts playing the disc
automatically.
, The disc features an auto playback function.
, “AUTO PLAY” in “CUSTOM SETUP” is
set to “ON” (page 59).
Playback stops automatically.
Some functions such as Stop, Fast Play,
Slow Play, Slow-motion Play, Repeat
Play, Shuffle Play or Program Play cannot
be performed.
, Depending on the disc, you may not be able
to do some of the operations above. Refer to
the operating manual that comes with the
disc.
The language for the sound track cannot
be changed.
, Try using the DVD’s menu instead of the
direct selection button on the remote
(page 29).
, Multilingual tracks are not recorded on the
DVD being played.
, The DVD prohibits the changing of the
language for the sound track.
, Try using the DVD’s menu instead of the
direct selection button on the remote
(page 29).
, Multi-angles are not recorded on the DVD
being played.
, The angle can only be changed when the
“
” indicator lights up on the front panel
display (page 11).
, The DVD prohibits changing of the angles.
The player does not operate properly.
, When static electricity, etc., causes the
player to operate abnormally, unplug the
player.
5 numbers or letters are displayed on the
screen and on the front panel display.
, The self-diagnosis function was activated.
(See the table on page 66.)
The disc tray does not open and “LOCKED”
appears on the front panel display.
, Child Lock is set (page 28).
The disc tray does not open and “TRAY
LOCKED” appears on the front panel
display.
, Contact your Sony dealer or local
authorized Sony service facility.
Additional Information
, While playing discs with an auto pause
signal, the player stops playback at the auto
pause signal.
The angles cannot be changed.
“Data error” appears on the TV screen
when playing a DATA CD/DATA DVD.
, The MP3 audio track/JPEG image file you
want to play is broken.
, The data is not MPEG-1 Audio Layer III
data.
, The JPEG image file format does not
conform to DCF (page 49).
, The JPEG image file has the extension
“.JPG” or “.JPEG,” but is not in JPEG
format.
The subtitle language cannot be changed
or turned off.
, Try using the DVD’s menu instead of the
direct selection button on the remote
(page 29).
, Multilingual subtitles are not recorded on
the DVD being played.
, The DVD prohibits the changing of
subtitles.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continued
65US
The HDMI CONTROL function does not
work.
, When HDMI indicator does not light up on
the front panel, check the HDMI connection
(page 17).
, Set the “HDMI CONTROL” setting in
“CUSTOM SETUP” to “ON” (page 60).
, Make sure that the connected component is
compatible with the HDMI CONTROL
function. Please refer to the operating
instructions of the component for detailed
explanation.
, If you change the HDMI connection,
connect and disconnect the AC power cord,
or have a power failure, set the “HDMI
CONTROL” setting in “CUSTOM
SETUP” to “OFF,” then set the “HDMI
CONTROL” setting in “CUSTOM
SETUP” to “ON” (page 60).
Display language on the screen switches
automatically.
, When “LANGUAGE FOLLOW” is set to
“ON” in the “CUSTOM SETUP” (page 60),
the display language on the screen
automatically switches, according to the
language setting of the connected TV, if you
change the language settings on your TV,
etc.
Self-diagnosis Function
(When letters/numbers appear in the
display)
When the self-diagnosis function is activated
to prevent the player from malfunctioning, a
five-character service number (e.g., C 13 50)
with a combination of a letter and four digits
appears on the screen and the front panel
display. In this case, check the following
table.
C:13:50
First three
characters of
the service
number
Cause and/or corrective
action
C 13
The disc is dirty or recorded
in a format that this player
cannot play (page 8).
, Clean the disc with a
cleaning cloth or check its
format.
C 31
The disc is not inserted
correctly.
, Re-insert the disc
correctly.
The DVD player turns on automatically.
, HDMI input is selected using TV Interface.
Some TV has this function for HDMI
CONTROL.
, “HDMI CONTROL” in “CUSTOM
SETUP” is set to “ON” (page 60).
E XX
To prevent a malfunction, the
(xx is a number) player has performed the
self-diagnosis function.
, Contact your nearest
Sony dealer or local
authorized Sony service
facility and give the 5character service number.
Example: E 61 10
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
66
Specifications
System
General
Laser: Semiconductor laser
Signal format system: NTSC
Power requirements:
120 V AC, 60 Hz
Power consumption: 11 W
Dimensions (approx.):
430 × 43 × 210.4 mm (17 × 111/16 × 82/7
in.) (width/height/depth) incl. projecting
parts
Mass (approx.): 1.76 kg (37/8 lb)
Operating temperature: 5 ° C to 35 ° C
Operating humidity: 25 % to 80 %
Audio characteristics
Frequency response: DVD VIDEO (PCM
48 kHz): 2 Hz to 22 kHz (±0.5 dB)/
CD: 2 Hz to 20 kHz (±0.5 dB)
Wow and flutter: Less than detected value
(±0.001% W PEAK)
Outputs
Supplied accessories
Audio/video cord (1)
Remote Commander (remote) (1)
R6 (size AA) batteries (2)
Specifications and design are subject to
change without notice.
Additional Information
(Jack name: Jack type/Output level/Load
impedance)
LINE OUT (AUDIO): Phono jack/2 Vrms/
10 kilohms
DIGITAL OUT (OPTICAL): Optical
output jack/–18 dBm (wave length
660 nm)
DIGITAL OUT (COAXIAL): Phono jack/
0.5 Vp-p/75 ohms
HDMI OUT: HDMI 19 pin-Standard
Connector
COMPONENT VIDEO OUT(Y, PB, PR):
Phono jack/Y: 1.0 Vp-p/PB, PR:
interlace*1 = 0.648 Vp-p, progressive or
interlace*2 = 0.7 Vp-p/75 ohms
*1 BLACK LEVEL (COMPONENT OUT) is ON
*2 BLACK LEVEL (COMPONENT OUT) is OFF
LINE OUT (VIDEO): Phono jack/1.0 Vp-p/
75 ohms
S VIDEO OUT: 4-pin mini DIN/
Y: 1.0 Vp-p, C: 0.286 Vp-p/75 ohms
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
67US
Language Code List
For details, see pages 46, 56.
The language spellings conform to the ISO 639: 1988 (E/F) standard.
Code Language
Code Language
Code Language
Code Language
1027
1028
1032
1039
1044
1045
1051
1052
1053
1057
1059
1060
1061
1066
1183
1186
1194
1196
1203
1209
1217
1226
1229
1233
1235
1239
1245
1248
1253
1254
1257
1261
1269
1283
1287
1297
1298
1299
1300
1301
1305
1307
1311
1313
1326
1327
1332
1334
1347
1349
1350
1352
1353
1356
1357
1358
1363
1365
1369
1376
1379
1393
1403
1408
1417
1428
1435
1507
1508
1509
1511
1512
1513
1514
1515
1516
1517
1521
1525
1527
1528
1529
1531
1532
1534
1535
1538
1539
1540
1543
1557
1564
1572
1581
1587
1613
1632
1665
1684
1697
1067
1070
1079
1093
1097
1103
1105
1109
1130
1142
1144
1145
1149
1150
1151
1157
1165
1166
1171
1174
1181
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Byelorussian
Bulgarian
Bihari
Bislama
Bengali;
Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
German
Bhutani
Greek
English
Esperanto
Spanish
Estonian
Basque
Persian
Finnish
Fiji
Faroese
French
Frisian
Irish
Scots Gaelic
Galician
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Italian
Hebrew
Japanese
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Korean
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laothian
Lithuanian
Latvian;
Lettish
1345 Malagasy
1436
1463
1481
1482
1483
1489
1491
1495
1498
1501
1502
1503
1505
1506
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Malay
Maltese
Burmese
Nauru
Nepali
Dutch
Norwegian
Occitan
(Afan)Oromo
Oriya
Punjabi
Polish
Pashto;
Pushto
Portuguese
Quechua
RhaetoRomance
Kirundi
Romanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sangho
SerboCroatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Tonga
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Wolof
Xhosa
Yoruba
Chinese
Zulu
1703 Not specified
Parental Control Area Code List
For details, see page 40.
Code Area
Code Area
Code Area
Code Area
2044
2047
2046
2057
2070
2079
2090
2092
2115
2165
2174
2109
2248
2238
2254
2276
2304
2363
2362
2376
2390
2379
2427
2424
2436
2489
2501
2149
2499
2086
2528
2184
Argentina
Australia
Austria
Belgium
Brazil
Canada
Chile
China
Denmark
Finland
France
Germany
India
Indonesia
Italy
Japan
Korea
Malaysia
Mexico
Netherlands
New Zealand
Norway
Pakistan
Philippines
Portugal
Russia
Singapore
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
68
Spain
Sweden
Switzerland
Thailand
United
Kingdom
Index
Symbols
16:9 57
4:3 LETTER BOX 57
4:3 PAN SCAN 57
48kHz/96kHz PCM 62
5.1 Channel Surround 21
Front panel display 11
Setup Display 55
DOLBY DIGITAL 46, 62
DOWNMIX 61
DTS 46, 62
DVD 7, 26
DVD+RW 7
DVD’s menu 29
DVD-RW 7
A
E
‘BRAVIA’ Theatre Sync 19
Numerics
EFFECT 54
F
Fast forward 42
FAST PLAY 28
Fast reverse 42
FILE 43
Film based software 19
Freeze Frame 42
Front panel display 11
H
BACKGROUND 58
Batteries 22
BLACK LEVEL 58
BLACK LEVEL
(COMPONENT OUT) 59
Handling discs 2
HDMI
AUDIO (HDMI) 62
HDMI CONTROL 19, 60
HDMI RESOLUTION 57
LANGUAGE FOLLOW 60
Hooking up 16
C
I
B
CD 8, 26
CHAPTER 43
CHAPTER VIEWER 44
Checking the audio signal
format 47
Child Lock 28
Connecting 17
Continuous play
CD/VIDEO CD 26
DVD 26
Control Menu 13
CUSTOM 55
CUSTOM PARENTAL
CONTROL 39
CUSTOM PICTURE MODE
36
CUSTOM SETUP 59
D
DATA CD 7, 49
DATA DVD 7, 49
DATE 52
DIGITAL OUT 61
Digital output 61
DIMMER 59
Display
Control Menu Display 13
INDEX 43
INTERVAL 54
J
JPEG 7, 49
JPEG RESOLUTION 57
L
LANGUAGE SETUP 56
Locating
a specific point by watching
the TV screen 42
M
MEMORY 37
MENU 56
MODE (MP3, JPEG) 53
MP3 7, 49
MULTI-DISC RESUME 28,
60
N
NORMAL (INTERLACE) 19
O
On-screen display
Control Menu Display 13
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
P
PARENTAL CONTROL 39
PAUSE MODE 60
PBC Playback 30
PICTURE NAVIGATION 44,
51
PLAY LIST 29
PROGRAM 32
Program Play 32
PROGRESSIVE AUTO 19
PROGRESSIVE VIDEO 19
Q
QUICK 56
Quick Setup 24, 56
R
Remote 12, 22, 23
REPEAT 34
Repeat Play 34
REPLAY 27
RESET 56
S
Scan 42
SCENE 43
SCREEN SAVER 58
SCREEN SETUP 57
Searching 42
SETUP 55
Setup Display 55
SHARPNESS 37
SHUFFLE 34
Shuffle Play 34
Slide Show 52
SLOW PLAY 28
Slow-motion Play 42
Speakers
Hooking up 20
SUBTITLE 27, 52, 56
Surround 48
Additional Information
A-B REPEAT 35
ADVANCE 27
ALBUM 43
Album 49
ANGLE 27
AUDIO 46, 56
AUDIO DRC 61
AUDIO SETUP 61
AUTO (BGM) 32, 46, 53
AUTO PLAY 59
AUTO POWER OFF 59
AV SYNC 38
Setup Display 55
ORIGINAL 29
ORIGINAL/PLAY LIST 29
OSD 56
T
TIME/TEXT 30
TITLE 43
TITLE VIEWER 44
TOP MENU 29
TRACK 43
Track 11
TRACK SELECTION 60
TRACK VIEWER 44
Troubleshooting 63
TV TYPE 57
TVS (TV Virtual Surround) 48
,continued
69US
U
Usable discs 8
V
Video based software 19
VIDEO CD 7, 26
Z
ZOOM 27, 52
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
US
70
Tabla de contenido
Conexiones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Conexión del reproductor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Paso 1: Conexión de los cables del video/HDMI (interfaz multimedia de alta
definición). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Acerca de las funciones CONTROL HDMI para ‘BRAVIA’ Theatre Sync
(sólo para conexiones HDMI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Paso 2: Conexión de los cables de audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Paso 3: Conexión del cable de alimentación . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Paso 4: Preparación del control remoto. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Control del televisor mediante el control remoto . . . . . . . . . . . . . . . . . . . 10
Paso 5: Ajuste rápido. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Reproducción . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Reproducción de discos. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
ES
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
1ES
Conexiones
Conexión del reproductor
Siga los pasos 1 a 5 para conectar el reproductor y ajustar sus valores.
Notas
•
•
•
•
•
Consulte la lista de accesorios suministrados en “Especificaciones” (página 83)
Enchufe los cables firmemente para evitar ruidos no deseados.
Consulte el manual de instrucciones suministrado con los componentes que va a conectar.
No es posible conectar este reproductor a un televisor que no tenga una toma de entrada de video.
Asegúrese de desconectar el cable de corriente de cada componente antes de realizar las conexiones.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
ES
2
Paso 1: Conexión de los cables del video/HDMI
(interfaz multimedia de alta definición)
Conexiones
Mediante un cable de vídeo, conecte el reproductor al monitor, proyector o componente de
audio, como un amplificador de AV (receptor). Seleccione uno de los patrones A a D según la
toma de entrada del monitor del televisor, del proyector o del componente de audio.
Para visualizar imágenes de señal progresiva (480 p) con un televisor, un proyector o un monitor
compatible, debe utilizar el patrón C. Seleccione el patrón D al conectar a un televisor, un
proyector o un componente de audio equipado con entrada HDMI (interfaz multimedia de alta
definición).
A
INPUT
(amarillo)
VIDEO
Cable de audio/
vídeo
(suministrado)
Cable S VIDEO
(s vídeo) (no
suministrado)
INPUT
S VIDEO
L
B
AUDIO
R
Televisor, proyector o
componente de audio
Televisor, proyector o
componente de audio
(amarillo)
a S VIDEO OUT
(salida de s vídeo)
a LINE OUT (VIDEO)
(salida línea) (vídeo)
a HDMI OUT (salida de
la interfaz multimedia
de alta definición)
Cable de conexión
HDMI (no suministrado)
(verde)
(azul)
(rojo)
a COMPONENT
VIDEO OUT
(salida de vídeo
componente)
Cable de conexión
de vídeo componente
(no suministrado)
Reproductor CD/
DVD (reproductor
de discos
compactos y
videodiscos
digitales)
COMPONENT
VIDEO IN
C
Y
(verde)
D
PB
(azul)
PR
(rojo)
HDMI IN
Televisor, proyector o
componente de audio
Televisor, proyector o
componente de audio
l : flujo de señal
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continúa
3ES
A Toma de entrada de vídeo
Conecte la clavija amarilla del cable de audio/
vídeo (suministrado) a la toma amarilla
(vídeo). Disfrutará de imágenes de calidad
estándar.
En esta conexión, presione el botón
PROGRESSIVE (progresivo) del panel
frontal para seleccionar “NORMAL
(INTERLACE)” (normal (entrelazado))
(predeterminado).
Cuando se conecte a un televisor Sony que
sea compatible con la función CONTROL
HDMI, consulte la página 5.
Al realizar la conexión a la toma HDMI
OUT (salida de la interfaz multimedia de
alta definición)
Realice los pasos siguientes. Una
manipulación incorrecta podría dañar la toma
HDMI OUT y el conector.
1
B Toma de entrada S VIDEO (s
vídeo)
Conecte un cable S VIDEO (s vídeo) (no
suministrado). Disfrutará de imágenes de alta
calidad.
En esta conexión, presione el botón
PROGRESSIVE (progresivo) del panel
frontal para seleccionar “NORMAL
(INTERLACE)” (normal (entrelazado))
(predeterminado).
C Tomas de entrada de vídeo
componente (Y, PB, PR)
Conecte el componente a través de las tomas
de COMPONENT VIDEO OUT (salida de
vídeo componente) con un cable de vídeo
componente (no suministrado) o con tres
cables de vídeo (no suministrados) del mismo
tipo y longitud. Este tipo de conexiones
proporciona imágenes de alta calidad con una
reproducción fiel de los colores.
Si el televisor admite señales de formato
progresivo de 480 p, utilice esta conexión y
presione el botón PROGRESSIVE
(progresivo) del panel frontal para emitir
señales progresivas. Para obtener más
información, consulte “Uso del botón
PROGRESSIVE (progresivo)” (página 6).
D Toma de entrada HDMI/DVI
(interfaz multimedia de alta
definición/interfaz visual digital)
Utilice un cable Sony HDMI certificado (no
suministrado) para disfrutar de una imagen y
un sonido digitales de alta calidad a través de
la toma HDMI OUT (salida de la interfaz
multimedia de alta definición).
Alinee con cuidado la toma HDMI OUT
de la parte posterior del reproductor y
el conector HDMI mediante la
comprobación de su forma.
Asegúrese de que la conector no esté al
revés ni inclinada.
La conector está al revés
2
Inserte el conector HDMI directamente
en la toma HDMI OUT.
No doble ni presione el conector HDMI.
Para conectarlo a un televisor con entrada
DVI (interfaz visual digital)
Utilice un cable adaptador HDMI-DVI (no
suministrado). La toma DVI (interfaz visual
digital) no admitirá señales de audio, por lo
que deberá usar otra conexión de audio
además de esta conexión (página 7). Además,
no es posible conectar la toma HDMI OUT
(salida de la interfaz multimedia de alta
definición) a las tomas DVI (interfaz visual
digital) no compatibles con HDCP
(Protección de contenido digital de alto ancho
de banda) (por ejemplo, tomas DVI (interfaz
visual digital) en pantallas de PC
(computadora personal)).
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
ES
4
No está recta
Si lo conecta a un televisor de pantalla 4:3
estándar
Según el disco, es posible que la imagen no
quepa en la pantalla del televisor. Para
cambiar la relación de aspecto, consulte la
página 69.
• No conecte una videograbadora, etc., entre el
televisor y el reproductor. Si pasa las señales del
reproductor a través de la videograbadora, es
posible que no reciba una imagen clara en la
pantalla del televisor. Si el televisor sólo tiene una
toma de entrada de audio/vídeo, conecte el
reproductor a esta toma.
Videograbadora
Reproductor de
CD/DVD
(reproductor de
discos compactos
y videodiscos
digitales)
Si conecta los componentes Sony compatibles con
la función CONTROL HDMI con un cable HDMI
(no suministrado), podrá disfrutar de las siguientes
funciones:
• Reproducción mediante una pulsación
(página 14)
• Desconexión del sistema
Cuando apague el televisor mediante el botón [/1
del control remoto del televisor, los componentes
compatibles con la función CONTROL HDMI se
apagarán automáticamente.
Conexiones
Notas
Acerca de las funciones
CONTROL HDMI para ‘BRAVIA’
Theatre Sync (sólo para
conexiones HDMI)
Preparación para las funciones de
‘BRAVIA’ Theatre Sync
Televisor
Conectar
directamente
• Si la imagen aparece demasiado blanca cuando
utiliza las conexiones A o B, ajuste la opción
“BLACK LEVEL” de “SCREEN SETUP” en
“OFF” (página 71).
• Asegúrese de desconectar el cable HDMI cuando
mueva el reproductor.
• Si coloca el reproductor en un armario con el
cable HDMI conectado, no ejerza presión
excesiva en la pared del armario. Podría dañar el
cable HDMI o la toma HDMI OUT.
• Cuando conecte o desconecte la unidad, no
enrosque ni gire el conector HDMI.
Ajuste “HDMI CONTROL” en “ON” en el
“CUSTOM SETUP” (página 73). Para obtener más
información acerca de la configuración del
televisor, consulte el manual de instrucciones
suministrado con el mismo.
Nota
En función del componente conectado, es posible
que la función CONTROL HDMI no funcione.
Consulte el manual de instrucciones suministrado
con el componente.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continúa
5ES
Uso del botón PROGRESSIVE
(progresivo)
El botón PROGRESSIVE (progresivo)
permite seleccionar el formato de señal que
utilizará el reproductor para emitir señales de
video (Progresivo o Entrelazado) y el método
de conversión para las señales progresivas.
Cada vez que presione el botón
PROGRESSIVE (progresivo), la pantalla
cambiará de la siguiente forma:
,
PROGRESSIVE AUTO
(progresivo automático)
m
PROGRESSIVE VIDEO
(progresivo video)
m
NORMAL (INTERLACE)
(normal (entrelazado))
◆PROGRESSIVE AUTO (progresivo
automático)
Seleccione este ajuste cuando:
– el televisor acepte señales progresivas y
– esté conectado a las tomas COMPONENT
VIDEO OUT (salida de vídeo componente).
Normalmente seleccione este ajuste si se
cumple la condición anterior. Detectará en
forma automática el tipo de software y
seleccionará el método de conversión
adecuado.
Tenga presente que si selecciona estos ajustes
y no se cumple ninguna de las condiciones
mencionadas anteriormente, la imagen no
será nítida o no aparecerá ninguna imagen.
◆PROGRESSIVE VIDEO (progresivo video)
Seleccione este ajuste cuando:
– el televisor acepte señales progresivas y
– esté conectado a las tomas COMPONENT
VIDEO OUT (salida de vídeo componente) y
– desea fijar el método de conversión en
PROGRESSIVE VIDEO (progresivo video)
para el software basado en video. Seleccione
este ajuste si la imagen no es nítida cuando
selecciona PROGRESSIVE AUTO
(progresivo automático).
Tenga presente que si selecciona estos ajustes
y no se cumple ninguna de las condiciones
mencionadas anteriormente, la imagen no
será nítida o no aparecerá ninguna imagen.
◆NORMAL (INTERLACE) (normal
(entrelazado))
Seleccione este ajuste cuando:
– el televisor no acepte señales progresivas o
– esté conectado a tomas que no sean las
tomas COMPONENT VIDEO OUT (salida
de vídeo componente), LINE OUT
(VIDEO) (salida línea (vídeo)) o S VIDEO
OUT (salida de s vídeo).
Acerca de los tipos de software de DVD
(videodisco digital) y el método de
conversión
El software de DVD (videodisco digital)
puede dividirse en dos tipos: el software
basado en cine y el software basado en video.
El software basado en video proviene de
programas de televisión, como telenovelas y
comedias, y muestra imágenes a 30
fotogramas/60 campos (25 fotogramas/50
campos) por segundo. El software basado en
cine proviene de películas y muestra
imágenes a 24 fotogramas por segundo.
Existe software de DVD (videodisco digital)
que contiene tanto video como películas.
Para que estas imágenes parezcan naturales
en la pantalla cuando se emiten en formato
progresivo, las señales progresivas deben
convertirse para que coincidan con el tipo de
software de DVD (videodisco digital) que
está viendo.
Nota
Si reproduce software basado en video en formato
de señales progresivas, es posible que algunas
partes de determinados tipos de imágenes no
parezcan naturales debido al proceso de conversión
si se emiten mediante las tomas COMPONENT
VIDEO OUT (salida de vídeo componente). Las
imágenes emitidas a través de las tomas S VIDEO
OUT (salida de s vídeo) y LINE OUT (VIDEO)
(salida línea (vídeo)) no se verán afectadas al
utilizar un formato normal (entrelazado).
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
ES
6
Paso 2: Conexión de los cables de audio
Seleccione uno de los siguientes patrones, A o B, según la toma de entrada del monitor del
televisor, del proyector o del componente de audio, como un amplificador de AV (receptor).
De este modo podrá escuchar el sonido.
(blanco)
(amarillo)*
INPUT
A
VIDEO
(blanco)
Conexiones
Cable de
audio/video
(suministrado)
(rojo)
L
(amarillo)*
AUDIO
(rojo)
R
TV (televisor), proyector
o componente de audio
a LINE OUT L/R (AUDIO)
(salida línea izquierda/derecha)
a DIGITAL OUT (COAXIAL o OPTICAL)
(salida digital coaxial o óptica)/HDMI OUT
(salida de la interfaz multimedia de alta definición)
COAXIAL
OPTICAL
HDMI OUT
o
DIGITAL OUT
Cable de conexión digital
óptica (no suministrado)
Quite la tapa de la toma
antes de conectar.
Reproductor
de CD/DVD
(reproductor
de discos
compactos y
videodiscos
digitales)
o
Cable de conexión digital
coaxial (no suministrado)
Cable de conexión HDMI (no suministrado)
[Altavoces]
Posterior
(izquierdo)
Frontal
(izquierdo)
Central
a la entrada digital coaxial o óptica/
HDMI (salida de la interfaz
multimedia de alta definición
[Altavoces]
Posterior
(derecho)
Componente de audio
que dispone de un
codificador
B
Frontal
(derecho)
Altavoz
potenciador de
graves
: Flujo de señal
* La clavija amarilla se utiliza para señales de vídeo (página 3).
z Sugerencia
Para la colocación correcta de los altavoces, consulte el manual de instrucciones suministrado con los
componentes conectados.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continúa
7ES
A Tomas de entrada de audio I/D
Esta conexión utilizará los dos altavoces del
televisor o del componente de audio para el
sonido.
B Tomas de entrada de audio
• Al realizar la conexión a la toma HDMI OUT
(salida de la interfaz multimedia de alta
definición), haga coincidir el conector HDMI
(interfaz multimedia de alta definición) con la
toma. No doble el cable HDMI (interfaz
multimedia de alta definición) ni ejerza presión
sobre el mismo.
digital
Si el componente de audio dispone de
decodificador Dolby*1 Digital o DTS*2 y una
toma de entrada digital, utilice esta conexión.
Conexión mediante un cable digital coaxial o
óptica/HDMI (interfaz multimedia de alta
definición) (no suministrado). Podrá disfrutar
de los efectos de sonido envolvente de Dolby
Digital (5.1ch) y DTS (5.1ch).
Si se conecta a un componente de audio de
Sony que sea compatible con la función
CONTROL HDMI, consulte el manual de
instrucciones suministrado con el mismo.
*1
*2
Fabricado bajo licencia de Dolby Laboratories.
Dolby, Pro Logic y el símbolo de la doble D son
marcas comerciales de Dolby Laboratories.
“DTS” y “DTS Digital Out” son marcas
comerciales registradas de DTS, Inc.
Notas
• Después de establecer la conexión, asegúrese de
ajustar “DOLBY DIGITAL” en “DOLBY
DIGITAL” y “DTS (sistema digital de sala de
cine)” en “ON” en Ajuste rápido (página 11).
• Al conectar un componente de audio que admita
la frecuencia de muestreo de 96 kHz, ajuste
“48kHz/96kHz PCM” de “AUDIO SETUP” en
“96kHz/24bits” (página 76).
• Los efectos TVS (sonido envolvente virtual de
televisor) de este reproductor no son compatibles
con esta conexión.
• Cuando conecte el reproductor a un componente
de audio mediante un cable HDMI (interfaz
multimedia de alta definición), tendrá que realizar
alguno de los pasos siguientes:
– Conecte el componente de audio al televisor con
el cable HDMI (interfaz multimedia de alta
definición).
– Conecte el reproductor al televisor con un cable
de video que no sea el cable HDMI (interfaz
multimedia de alta definición) (cable de video
componente, cable de S video o cable de audio/
video).
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
ES
8
Paso 3: Conexión del cable de alimentación
Conecte los cables de alimentación del reproductor y del televisor a una toma de ca.
Se puede controlar el reproductor con el control remoto suministrado. Inserte dos pilas R6
(tamaño AA) de forma que coincidan sus extremos 3 y # con las marcas del interior del
compartimiento. Al utilizar el control remoto, oriéntelo hacia el sensor remoto
del
reproductor.
Conexiones
Paso 4: Preparación del control remoto
Notas
• No deje el control remoto en lugares extremadamente cálidos o húmedos.
• No permita que caigan objetos extraños sobre el control remoto, especialmente cuando sustituya las pilas.
• No exponga el sensor del control remoto a la luz directa del sol ni a dispositivos de iluminación. Si lo hace,
pueden producirse fallas en el funcionamiento.
• Cuando no vaya a usar el control remoto durante un tiempo prolongado, extraiga las pilas para evitar
posibles daños por fugas y corrosión.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continúa
9ES
Control del televisor mediante el
control remoto
Control de un televisor de otro
proveedor con el control remoto
Puede controlar el nivel del sonido, la fuente
de entrada y el interruptor de alimentación del
televisor Sony con el control remoto
suministrado.
También puede controlar el nivel del sonido,
la fuente de entrada y el interruptor de
alimentación de un televisor de otro
proveedor con el control remoto
suministrado.
Si el televisor figura en la tabla que aparece a
continuación, establezca el código del
fabricante correspondiente.
TV (televisor)
VOL
(volumen)
+/–
Botones
numéricos
TV/VIDEO
(televisor/
video)
1
Mientras mantiene presionado TV
(televisor) [/1, presione los botones
numéricos para seleccionar el código
del fabricante del televisor (consulte
la tabla que se proporciona a
continuación).
2
Suelte TV (televisor) [/1.
Códigos de televisores controlables
Puede controlar el televisor mediante los
botones que se indican a continuación.
Si aparece más de un código, ingréselos uno
tras otro hasta encontrar el que funciona con
su televisor.
Presionando
Puede
Fabricante
Número de código
TV
(televisor) [/1
Encender o apagar el
televisor
Sony
01 (predeterminado)
Daewoo
04, 22
VOL
(volumen) +/–
Ajustar el volumen del
televisor
Hitachi
02, 04
TV/VIDEO
(televisor/video)
Cambiar la fuente de entrada
del televisor entre éste y otras
fuentes de entrada
JVC
09
LG/Goldstar
04
MGA/Mitsubishi 04, 13
Panasonic
Nota
Según la unidad conectada, podrá controlar el
televisor utilizando algunos o todos los botones del
control remoto suministrado.
19
Philips
21
RCA
04, 10
Samsung
04, 20
Sharp
18
Toshiba
07, 18
Notas
• Al sustituir las pilas del control remoto, es posible
que el código recupere el valor de fábrica. Vuelva
a ajustar el código apropiado.
• Según la unidad que conecte, podrá controlar el
televisor utilizando algunos o todos los botones
del control remoto suministrado.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
ES
10
Paso 5: Ajuste rápido
Siga los pasos siguientes para realizar el mínimo de ajustes básicos para utilizar el reproductor.
Para saltar un ajuste, presione >. Para volver al ajuste anterior, presione ..
Conexiones
ENTER
(ingresar)
1 Encienda el televisor.
2 Presione [/1.
3 Cambie el selector de entrada del
televisor para que la señal del
reproductor aparezca en la
pantalla del televisor.
En la parte inferior de la pantalla,
aparecerá “Press [ENTER] to run
QUICK SETUP”. Si este mensaje no
aparece, seleccione “QUICK” en
“SETUP” del menú de control para
ejecutar el ajuste rápido (página 68).
4 Presione ENTER (ingresar) sin
insertar ningún disco.
Aparece la pantalla de ajustes que le
permitirá seleccionar el idioma utilizado
en la pantalla.
LANGUAGE SETUP
OSD:
MENU:
AUDIO:
SUBTITLE:
ENGLISH
ENGLISH
FRENCH
SPANISH
PORTUGUESE
5 Presione X/x para seleccionar un
idioma.
El reproductor muestra el menú y los
subtítulos en el idioma seleccionado.
6 Presione ENTER (ingresar).
Aparece la pantalla de ajustes que le
permitirá seleccionar la relación de
aspecto del televisor que vaya a conectar.
SCREEN SETUP
16:9
TV TYPE:
16:9
HDMI RESOLUTION:
JPEG RESOLUTION: 4:3 LETTER BOX
4:3 PAN SCAN
YCBCR/RGB (HDMI):
ON
SCREEN SAVER:
JACKET PICTURE
BACKGROUND:
ON
BLACK LEVEL:
OFF
BLACK LEVEL (COMPONENT OUT):
FULL
4:3 OUTPUT:
7 Presione X/x para seleccionar el
ajuste que coincida con el tipo de
televisor.
◆ Si tiene un televisor con pantalla
panorámica o uno 4:3 estándar con el
modo de pantalla panorámica
• 16:9 (página 69)
◆ Si tiene un televisor 4:3 estándar
• 4:3 LETTER BOX (tipo buzón) o 4:3
PAN SCAN (exploración PAN)
(página 69)
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continúa
11ES
8 Presione ENTER (ingresar).
Aparece la pantalla de ajustes que le
permitirá seleccionar el tipo de toma
utilizada para conectar el componente de
audio.
Is this player connected to an amplifier
(receiver)? Select the type of jack you
are using.
YES
LINE OUTPUT L/R(AUDIO)
DIGITAL OUTPUT
NO
9 Presione X/x para seleccionar (si
existe) el tipo de toma que utilice
para conectar a un componente de
audio y, a continuación, presione
ENTER (ingresar).
Si no conectó elcomponente de audio,
seleccione “NO” y vaya al paso 13.
Si conectó el componente de audio sólo
con un cable de audio, seleccione “YES:
LINE OUTPUT L/R (AUDIO)” y vaya al
paso 13.
Si conectó un componente de audio
mediante un cable digital coaxial, óptica/
HDMI (interfaz multimedia de alta
definición) seleccione “YES: DIGITAL
OUTPUT”.
10Presione X/x para seleccionar el
tipo de señal Dolby Digital que
desee enviar al componente de
audio.
Si el componente de audio dispone de
decodificador Dolby Digital, seleccione
“DOLBY DIGITAL”. De lo contrario,
seleccione “D-PCM”.
AUDIO SETUP
AUDIO DRC:
STANDARD
DOWNMIX:
DOLBY SURROUND
DIGITAL OUT:
ON
D-PCM
DOLBY DIGITAL:
DTS:
D-PCM
48kHz/96kHz PCM: DOLBY DIGITAL
AUDIO (HDMI):
AUTO
11Presione ENTER (ingresar).
Se selecciona “DTS” (sistema digital de
sala de cine).
AUDIO SETUP
AUDIO DRC:
STANDARD
DOWNMIX:
DOLBY SURROUND
DIGITAL OUT:
ON
D-PCM
DOLBY DIGITAL:
DTS:
OFF
OFF
48kHz/96kHz PCM:
ON
AUDIO (HDMI):
12Presione X/x para seleccionar si
desea o no enviar una señal DTS
(sistema digital de sala de cine) al
componente de audio.
Si el componente de audio dispone de
decodificador DTS, seleccione “ON”. De
lo contrario, seleccione “OFF”.
13Presione ENTER (ingresar).
El ajuste rápido ha finalizado. Todas las
conexiones y operaciones de ajuste se
han completado.
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
ES
12
1 Encienda el televisor.
2 Presione [/1.
Reproducción
Reproducción de discos
*1
*5
*2
*3
*4
*6
3 Cambie el selector de entrada del
televisor para que la señal del
reproductor aparezca en la
pantalla del televisor.
◆ Cuando utilice un componente de
audio
Encienda el componente de audio y
seleccione el canal adecuado para que
pueda escuchar el sonido del reproductor.
Reproducción
Algunas operaciones pueden ser distintas o
estar limitadas en función del DVD
(videodisco digital) o VIDEO CD
(videodisco compacto).
Consulte las instrucciones de uso
suministradas con el disco.
El reproductor se enciende.
4 Presione A en el reproductor y
coloque un disco en la bandeja de
discos.
Botones
numéricos
CLEAR
(borrar)
TOP MENU
(menú
superior)
RETURN
(volver)
REPLAY
(reproducción)
ZOOM
(ampliación)
SLOW PLAY
(reproducción
lenta)
MENU
(menú)
ENTER
(ingresar)
DISPLAY
(indicación)
ADVANCE
(avance)
FAST PLAY
(reproducción
rápida)
ANGLE
(ángulo)
SUBTITLE
(subtítulo)
*1 DVD video (video de videodisco digital).
*2 DVD-VR (videodisco digital sin función de
*3
*4
*5
*6
Con la cara de reproducción
hacia abajo
5 Presione H.
La bandeja de discos se cierra y el
reproductor inicia la reproducción
(continua). Ajuste el volumen en el
televisor o en el componente de audio.
De acuerdo con el disco, puede aparecer
un menú en la pantalla del televisor. Para
los DVD VIDEO (video de videodisco
digital), consulte página 16. Para los
VIDEO CD (videodiscos compactos),
consulte página 17.
grabación de video).
VCD (videodisco compacto).
CD (disco compacto).
DATA CD (disco compacto de datos).
DATA DVD (videodisco digital de datos).
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
,continúa
13ES
Para apagar el reproductor
Presione [/1. El reproductor entra en modo
de espera.
Reproducción mediante una pulsación
(sólo para conexiones HDMI)
Con una sola pulsación del botón H del
control remoto, el reproductor y el televisor se
encenderán automáticamente y la toma de
entrada del televisor cambiará al reproductor.
La reproducción comenzará
automáticamente.
La entrada del televisor también cambiará
automáticamente al reproductor en los
siguientes casos:
– Cuando presione los botones H, TOP
MENU, MENU o DISPLAY en el control
remoto.
Tenga en cuenta que, en el modo “AUDIO
(MP3)”, estos botones no funcionarán
durante la reproducción de pistas de audio
de CD o MP3.
– Si se ha cargado el disco con función de
reproducción automática.
z Sugerencia
El reproductor se puede apagar en forma automática
siempre que lo deje en modo de parada durante más
de 30 minutos. Para activar o desactivar esta
función, ajuste “AUTO POWER OFF” en
“CUSTOM SETUP” en “ON” o “OFF”
(página 72).
Notas sobre la reproducción de pistas de
sonido DTS (sistema digital de sala de
cine) de un DVD VIDEO (video de
videodisco digital)
• Las señales de audio DTS (sistema digital
de sala de cine) se emiten sólo a través de la
toma DIGITAL OUT (COAXIAL o
OPTICAL)/HDMI OUT (salida digital
coaxial o óptica/salida de la interfaz
multimedia de alta definición).
• Cuando reproduzca un DVD VIDEO (video
de videodisco digital) con pistas de sonido
DTS (sistema digital de sala de cine), ajuste
“DTS” (sistema digital de sala de cine) en
“ON” en “AUDIO SETUP” (página 76).
• Si conecta el reproductor al equipo de audio
sin utilizar un decodificador DTS (sistema
digital de sala de cine), no ajuste “DTS”
(sistema digital de sala de cine) de “AUDIO
SETUP” en “ON” (página 76). Es posible
que los altavoces emitan un ruido fuerte,
que podría afectar los oídos o dañar los
altavoces.
Nota
Los discos creados con grabadoras de DVD
(videodisco digital) deberán estar finalizados
correctamente para poder reproducirse. Para
obtener más información acerca de la finalización,
consulte el manual de instrucciones suministrado
con la grabadora de DVD (videodisco digital).
Downloaded
From DvDPlayer-Manual.com Sherwood Manuals
ES
14
Operaciones adicionales
Consulte la ilustración de la página 13 para
comprobar la posición de los siguientes
botones.
Funcionamiento
Detener
Presione x
Hacer una pausa
Presione X
Reanudar la
reproducción después
de la pausa
Presione X o H
Pasar al capítulo, pista Presione >
o escena siguiente en
el modo de
reproducción continua
Retroceder al capítulo, Presione .
pista o escena anterior
en el modo de
reproducción continua
Detener la
reproducción y
expulsar el disco
Presione Z
Cambio de ángulo
Presione ANGLE
durante la
reproducción.
Presione ANGLE
varias veces para
seleccionar un
número de ángulo.
Mostrar subtítulos
Presione SUBTITLE
durante la
reproducción.
Presione SUBTITLE
varias veces para
seleccionar un idioma
de subtítulos.
Volver a reproducir la
escena anterior*1
Presione
(REPLAY)
(reproducción) durante
la reproducción
Avanzar rápidamente
una pequeña parte de
la escena actual*2
Presione
(ADVANCE)
(avance) durante la
reproducción
Reproducción
Para
*1 Todos los discos de DVD (videodisco digital)
excepto para DVD+R (videodisco digital más
grabable)/DVD+RW (videodisco digital más
regrabable)/DVD+R DL (videodisco digital más
grabable de doble capa). Este botón no puede
utilizarse durante la reproducción de archivos de
video DivX*.
2
* Sólo para discos DVD (videodisco digital). Este
botón no puede utilizarse durante la reproducción
de archivos de video DivX*.
3
* Sólo para imágenes de video y JPEG (grupo
conjunto de expertos en fotografía) (salvo
imágenes FONDO). Puede mover la imagen
ampliada mediante C/X/x/c. Según el
contenido del disco, es posible que se cancele en
forma automática la función de zoom
(ampliación) cuando se mueva la imagen.
* DVP-NS78H solamente
Nota
Tal vez no pueda utilizar la función de repetición o
avance en ciertas escenas.
Aumentar la imagen*3 Presione ZOOM
(ampliación) varias
veces. Presione
CLEAR (borrar) para
cancelar.
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
15ES
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
Downloaded From DvDPlayer-Manual.com Sherwood Manuals
Printed on 70% or more recycled paper using
VOC (Volatile Organic Compound)-free
vegetable oil based ink.
Sony Corporation
Printed in MalaysiaSherwood Manuals
Downloaded
From DvDPlayer-Manual.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement