GFDL110EHWW - PC Richard

GFDL110EHWW - PC Richard
GFDL110EH
GE® 7.0 Cu. Ft. Capacity Electric Dryer with 200 ft. long-venting
Dimensions and Installation Information (in inches)
Electric Dryer Rating
240V
5600W, 24A, 60Hz
208V
4400W, 22A, 60Hz
Exhaust Options: 4-way via rear, right, left and bottom.
Circuit Requirements: An individual, properly grounded
branch circuit, protected by a 30-amp circuit breaker or
a time-delay fuse, is required.
Note: Dryer wall outlet must be located within 36”
of service cord entry and accessible when dryer is
mounted in position.
Installation Information: For complete information, see
installation instructions packed with your dryer.
For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
geappliances.com or call GE Answer Center®
service, 800.626.2000.
Listed by
Underwriters
Laboratories
Specification Revised 3/14
360499
GFDL110EH
GE® 7.0 Cu. Ft. Capacity Electric Dryer with 200 ft. long-venting
Special Installation Requirements:
Stacked Dimensions (in inches)
Stacked Installation:
•Brackets for stacking dryer over washer are not included with the dryer.
GEFLSTACK or part no. WE25X10018.
Alcove or Closet Installation:
•If your dryer is approved for installation in an alcove or closet, it will be
stated on a label on the dryer back.
•The dryer MUST be exhausted to the outside.
•Minimum clearances between dryer cabinet and adjacent walls or other
surfaces are: 0" either side, 3" front and rear.
•Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52".
•Closet doors must be louvered or otherwise ventilated and must contain a
minimum of 60 sq. in. of open area equally distributed. If this closet contains
both a washer and a dryer, doors must contain a minimum of 120 sq. in. of
open area equally distributed.
Pedestal Dimensions (in inches)
•No other fuel-burning appliance shall be installed in the same closet with
a gas dryer.
SBSD137HWW - white
Bathroom or Bedroom Installation:
•The dryer MUST be exhausted to the outdoors.
•The installation must conform with the local codes, or in the absence of
local codes, with the National Electric Code and National Fuel Gas Code, ANSI Z223
for gas dryers.
This optional 13" pedestal raises
the door opening and height of
the washer or dryer. Feet on 13"
pedestal allow it to adjust to
13
13-3/8" height.
27
Minimum Clearance other than Alcove or Closet Installations:
•Minimum clearances to combustible surfaces 0" both sides, 3" rear.
28-3/4
For more information on venting kits and accessories,
please call 1-800-GE-CARES.
For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
geappliances.com or call GE Answer Center®
service, 800.626.2000.
Above illustrations intended for dimensional reference only.
Refer to photography for actual product appearance.
2-1/2
Listed by
Underwriters
Laboratories
3-1/2
1-3/4 Gas Pipe Electrical
12
Connection Connection
Specification Revised 3/14
360499
GFDL110EH
GE® 7.0 Cu. Ft. Capacity Electric Dryer with 200 ft. long-venting
Dryer exhausting information—use metal
duct only vertical and horizontal ducting
Best performance
Maximum length
of 4" dia rigid
A 4
metal duct
B
A
Exhaust hood type
Number
A
B
4
2-1/2
of 90°
4"
2-1/2"
B
turns opening opening
Domestic dryer models
0
200 ft.
175 ft.
2-1/2
1
185 ft.
165 ft.
2
175 ft.
155 ft.
3
165 ft.
145 ft.
GE Frontload Long Vent 7.0
4
155 ft.
135 ft.
cu. ft. capacity electric dryer
(GFDL)
5
145 ft.
125 ft.
0
150 ft.
125 ft.
1
135 ft.
115 ft.
2
125 ft.
105 ft.
3
115 ft.
95 ft.
All Long Vent 6.0 - 8.0 cu. ft.
4
105
ft.
85
ft.
capacity electric & gas dryers
(GTDL)
5
95 ft.
75 ft.
0
90 ft.
60 ft.
All 6.0 - 8.3 cu. ft. capacity
1
60 ft.
45 ft.
models electric and gas dryers
2
45 ft.
35 ft.
(GFDS, GFDR, GFDN, GTDS,
3
35 ft.
25 ft.
GTDN, GHDN, GHDS, GTDP,
GLDP, GTDX, HTDP, HTDX)
4
25 ft.
15 ft.
0
90 ft.
60 ft.
1
60 ft.
45 ft.
2
45 ft.
35 ft.
DCVH480
3
35 ft.
25 ft.
0
46 ft.
37 ft.
1
37 ft.
30 ft.
2
30 ft.
22 ft.
All 3.6 cu. ft. (DSKS, DSKP)
electric dryers
3
23 ft.
15 ft.
0
56 ft.
42 ft.
1
48 ft.
34 ft.
2
40 ft.
26 ft.
Laundry Center GTUP270,
GTUN275
3
32 ft.
18 ft.
0
43 ft.
36 ft.
1
33 ft.
26 ft.
Laundry Center GTUP240
2
24 ft.
16 ft.
A
Dryer Exhausting Information – Metal Duct Only
For complete information, see installation instructions packed with your dryer.
Ducting Materials: For best performance, this dryer should be vented with 4” diameter
all rigid metal exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible
metal (semi-rigid) ducting can be used (Kit WX08X10077). In special installations, it may
be necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct.
A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid
metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4” diameter can
be maintained throughout the entire length of the transition duct. Please see installation
instruction packed with your dryer for complete instructions when using flexible metal (foil
type) ducting.
Exhaust Length Calculation:
1. Determine the number of 90° turns needed for your installation. If you exhaust to the
side or bottom of dryer, add one turn.
2. The maximum length of 4’ rigid (aluminum or galvanized) duct which can be tolerated is
shown in the table.
A turn of 45° or less may be ignored. Two 45° turns within the duct length should be
treated as a 90° elbow.
A turn over 45° should be treated as a 90° elbow.
Dryers must be exhausted to the outside.
Caution: For personal safety do not terminate exhaust into a chimney, under any enclosed
house floor (crawl space), or into an attic, since the accumulated lint could create a fire
hazard or moisture could cause damage. Never terminate the exhaust into a common duct
or plenum with a kitchen exhaust, since the combination of lint and grease could create a
fire hazard.
Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts, bird
nesting, etc. The wall cap must also be located at least 12" above the ground or any other
obstruction with the opening pointed down.
For more information on venting kits and accessories, please call 1-800-GE-CARES.
Listed by
Underwriters
Laboratories
For every extra 90° elbow, reduce the allowable vent system length by 10 ft.
Two 45° elbows will be treated like one 90° elbow.
For the side exhaust installations, add one 90° elbow to the chart.
The total vent system length includes all the straight portions and elbows of the system (transition
duct included).
Laundry Center length includes factory-installed elbow that does not impact vent length.
Specification Revised 3/14
360499
GFDL110EH
GE® 7.0 Cu. Ft. Capacity Electric Dryer with 200 ft. long-venting
Features and Benefits
• Dura Drum provides long-lasting dependability
• H
E SensorDry™ with dual thermistors continually monitors moisture and
temperature to prevent clothing wear and tear due to over-drying and
inconsistent heat
• Speed Dry quickly dries items and small loads for families on the go
• e
Dry option—energy saving option reduces dry temperatures on select
cycles without sacrificing performance
• 4 heat settings provide the right temperature for the right drying needs
• 6 dry cycles—additional cycles for your clothes-drying needs
• 200 ft. long-venting capability - Provides flexible installation
• Model GFDL110EHWW – White
Specification Revised 3/14
360499
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement