OF45150 TWIN STACK PORTABLE AIR COMPRESSOR

OF45150 TWIN STACK PORTABLE AIR COMPRESSOR
OF45150
OPERATOR’S MANUAL
TWIN STACK
PORTABLE AIR
COMPRESSOR
!
WARNING:
To reduce the risk of injury, the user
must read and understand the
Operator’s Manual before using this
product.
IN610301AV 6/04
Printed in U.S.A.
Table of Contents
Section
Safety Instructions
Section
Page
Page
Getting to Know Your Air
Compressor . . . . . . . . . . . . . . . . . . .11
Table of Contents . . . . . . . . . . . . . . . .2
Safety Instructions . . . . . . . . . . . . . . .3
Safety Signal Words . . . . . . . . . . . . .3
Before Using the Air
Compressor . . . . . . . . . . . . . . . . . . . .3
Spraying Precautions . . . . . . . . . . . .5
Breathable Air Warning . . . . . . . . . . .5
Warning Labels . . . . . . . . . . . . . . . . .6
Operating Your Air Compressor . . .13
Moisture in Compressed Air . . . . . .13
Operating Your Air Compressor . . .13
For Trouble-Free Operation . . . . . .13
Maintenance . . . . . . . . . . . . . . . . . . .14
Tank . . . . . . . . . . . . . . . . . . . . . . . . .15
Filter Removal, Inspection, and
Replacement . . . . . . . . . . . . . . . . . .15
Lubrication . . . . . . . . . . . . . . . . . . . .15
Storage . . . . . . . . . . . . . . . . . . . . . .15
Motor Specifications and
Electrical Requirements . . . . . . . . . .7
Power Supply and Motor
Specifications . . . . . . . . . . . . . . . . . .7
General Electrical Connections . . . . .7
110-120 Volt, 60 Hz Tool
Information . . . . . . . . . . . . . . . . . . . .8
Extension Cords . . . . . . . . . . . . . . . .8
Thermal Overload Protector . . . . . . .9
This manual contains information that is
very important to know and understand.
This information is provided for SAFETY
and to PREVENT EQUIPMENT PROBLEMS. To help recognize this information, observe the following symbols.
Warning indicates
a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Safety Signal Words
ardous situation which, if not avoided,
MAY result in minor or moderate injury.
!
Danger indicates
DANGER: an imminently haz-
!
WARNING:
!
CAUTION: potentially haz-
Caution indicates a
Notice indicates
important information, that if not followed, may cause damage to equipment.
NOTICE:
ardous situation which, if not avoided,
WILL result in death or serious injury.
Maintenance Schedule . . . . . . . . . .15
Troubleshooting . . . . . . . . . . . . . . . .16
Repair Parts . . . . . . . . . . . . . . . . . . .18
Notes . . . . . . . . . . . . . . . . . . . . . . . . .22
Glossary of Terms . . . . . . . . . . . . . . .9
Warranty . . . . . . . . . . . . . . . . . . . . . .24
Unpacking and Checking
Content . . . . . . . . . . . . . . . . . . . . . . .10
Installation . . . . . . . . . . . . . . . . . . . .10
Before Using the Air Compressor
3. Do not exceed pressure rating of any
component in system.
Air compressors are utilized in a variety
of air system applications. Because air
compressors and other components
(material pump, spray gun, filters, lubrications, hoses, etc.) used make up a
high pressure pumping system, the following safety precautions should be
observed at all times. Only persons well
acquainted with these rules of safe operation should be allowed to use the air
compressor.
!
4. Protect material lines and air lines
from damage or puncture. Keep hose
and power cable away from sharp
objects, chemical spills, oil, solvents,
and wet floors.
5. Never point a spray gun at oneself or
any other person. Accidental discharge may result in serious injury.
6. Check hoses for weak or worn condition, before each use, making certain
all connections are secure; do not
use if deficiency is found. Notify an
authorized service facility for examination or repair.
WARNING:
All electrical work should be
done by a qualified (licensed or
certified) electrician. On a properly wired circuit, the black
wires supply a voltage potential
even when the unit is off.
7. Release all pressures within system
slowly; dust and debris may be harmful.
1. Read instruction manuals for each
component carefully, before attempting to assemble, disassemble or
operate your particular system.
!
Disconnect power and depressurize system before servicing
air compressor! (Turn pressure
regulator knob fully clockwise
after shutting off compressor.)
2. Wear safety glasses (meeting ANSI
Z87.1 or in Canada CSA Z94.3-99)
and use hearing protection when
operating the pump or unit. Everyday
glasses are not safety glasses.
2
WARNING:
3
Safety Instructions (continued)
19. When spraying with solvent of toxic
chemicals, follow instructions provided by the chemical manufacturer.
8. Follow all local electrical and safety
codes, as well as the National
Electrical Code (NEC) and the
Occupational Safety and Health Act
(OSHA).
20. Spray in a well ventilated area, to
keep fumes from collecting and causing health and fire hazards.
9. Wiring and fuses should follow electrical codes, current capacity, and be
properly grounded.
21. Do not spray in vicinity of open
flames or other places where a spark
can cause ignition. Do not smoke
when spraying paint, insecticides, or
other flammable substances.
10. Electric motors must be securely and
adequately grounded. See grounding
instructions and extension cord information in this manual.
22. Use a respirator when spraying.
11. Always disconnect power source
before working on or near a motor, or
its connected load. If power disconnect point is out-of-sight, lock it in the
open position and tag to prevent
unexpected application of power.
23. NEVER reset safety valve or pressure switch. Keep safety valve free
from paint and other accumulations.
This provides safety against over
pressure.
12. Guard all moving parts; keep visitors
away. Never allow children in work
area.
24. Do regular maintenance; keep all
nuts, bolts, and screws tight, to be
sure equipment is in safe working
condition .
13. Use only a properly grounded outlet
that will accept a three pronged plug,
and wear shoes to prevent shock
hazards.
25. Keep cleaning rags and other flammable waste materials in a tightly
closed metal container and dispose of
later in the proper fashion.
14. Be careful when touching exterior of
operating motor; it may be hot
enough to cause injury.
26. Drain tanks of moisture after each
day’s use. If unit will not be used for a
while, it is best to leave drain cock
open until such time as it is to be
used. This will allow moisture to completely drain out and help prevent
corrosion of inside of tank.
15. Protect power cable from coming in
contact with sharp objects.
16. Clean electrical or electronic equipment with an approved cleaning
agent, such as dry, nonflammable
cleaning solvent.
27. Inspect tank yearly for rust, pin holes
or any other imperfections that could
cause it to become unsafe. NEVER
weld or drill holes in air tank.
17. To avoid spontaneous combustion,
discard waste rags into approved
metal waste cans.
Spraying Precautions
!
3. Do not direct paint or other sprayed
material at the compressor. Locate
compressor as far away from the
spraying area as possible to minimize
overspray accumulation on the compressor.
WARNING:
Do not spray flammable materials in vicinity of open flame or
near ignition sources including
the compressor unit.
4. When spraying or cleaning with solvents or toxic chemicals, follow the
instructions provided by the chemical
manufacturer.
1. Do not smoke when spraying paint,
insecticides, or other flammable substances.
2. Use a face mask/respirator when spraying and
spray in a well ventilated
area to prevent health and
fire hazards.
!
DANGER:
Breathable Air Warning
This compressor/pump is not equipped and should not be used “as
is” to supply breathing quality air. For any application of air for
human consumption, the air compressor/pump will need to be fitted
with suitable in-line safety and alarm equipment. This additional
equipment is necessary to properly filter and purify the air to meet
minimal specifications for Grade D breathing as described in
Compressed Gas Association Commodity Specification G 7.1 - 1966,
OSHA 29 CFR 1910. 134, and/or Canadian Standards Associations
(CSA).
DISCLAIMER OF WARRANTIES
In the event the compressor is used for the purpose of breathing air
application and proper in-line safety and alarm equipment is not
simultaneously used, existing warranties shall be voided, and
Campbell Hausfeld disclaims any liability whatsoever for any loss,
personal injury or damage.
18. Never store flammable liquids or
gases in vicinity of compressor.
4
5
Safety Instructions (continued)
Motor Specifications and
Electrical Requirements
Warning Labels
Power Supply and Motor Specifications
Find and read all warning labels found on
the air compressor shown below
!
The A-C motor used on this compressor
is a capacitor start, capacitor run nonreversible induction type, having the following specifications. It is wired at the
factory for operation on 110V-120V AC,
60 Hz service.
WARNING:
To reduce the risk of electrical
hazards, fire hazards or damage
to the tool, use proper circuit
protection. Your tool is wired at
the factory for operation using
the voltage shown. Connect
tool to a power line with the
appropriate voltage and a 15amp branch circuit. Use a 15amp time delay type fuse or circuit breaker. To reduce the risk
of shock or fire, if power cord is
worn or cut, or damaged in any
way, have it replaced immediately.
Voltage
Amperes
Hertz (Cycles)
Phase
RPM
110-120
14.5
60
Single
3450
General Electrical Connections
!
DANGER:
!
Do not permit fingers to touch
the terminals of plug when
installing or removing the plug
to or from the outlet.
To reduce the risk of electrocution:
1. Use only identical replacement parts when servicing.
Servicing should be performed by a qualified technician.
DK724100AV 1000
6
WARNING:
2. Do not use in rain or where
floor is wet. This too is
intended for indoor residential use only.
7
Motor Specifications and
Electrical Requirements (continued)
Thermal Overload Protector
4. Lack of proper ventilation.
!
110-120 volt, 60Hz Tool Information
If the grounding instructions are not completely understood, or if you are in doubt
as to whether the tool is properly grounded check with a qualified electrician or
service personnel.
The plug supplied on your tool may not
fit into the outlet you are planning to use.
Your local electrical code may require
slightly different power cord plug connections. If these differences exist refer to
and make the proper adjustments per
you local code before your tool is
plugged in and turned on.
!
In the event of a malfunction or breakdown, grounding provides a path of least
resistance for electrical current to reduce
the risk of electric shock. This tool is
equipped with an electric cord having an
equipment-grounding conductor and a
grounding plug, as shown. The plug must
be plugged into a matching outlet that is
properly installed and grounded in accordance with all local codes and ordinances.
WARNING:
If not properly grounded, this
tool can cause an electrical
shock, particularly when used
in damp locations, in proximity
of plumbing, or out of doors.
CAUTION:
5. Unit is being used with an extension
cord.
This compressor is equipped
with an automatic reset thermal
overload protector which will
shut off motor if it becomes
overheated.
See Troubleshooting Chart for corrective
action.
!
CAUTION:
The motor must be allowed to
cool down before start-up is
possible. The motor will automatically restart without warning if left plugged into electrical
outlet, and the motor is turned
on.
If thermal overload protector shuts motor
OFF frequently look for the following
causes.
1. Low voltage.
2. Wrong gauge wire.
3. Clogged air filter.
Glossary of Terms
3-Prong Plug
Do not modify the plug provided. If it will
not fit the outlet, have the proper outlet
installed by a qualified electrician.
Properly
Grounded
3-Prong
Outlet
Improper connection of the equipmentgrounding conductor can result in a risk
of electric shock. The conductor with
insulation having an outer surface that is
green with or without yellow stripes is the
equipment-grounding conductor. If repair
or replacement of the electric cord or
plug is necessary, do not connect the
equipment-grounding conductor to a live
terminal.
TEST
RESET
Grounding Prong
Extension Cords
2. To avoid loss of power and overheating, additional air hose must be used
to reach work area instead of extension cords.
1. The air compressor should be located
where it can be directly plugged into
an outlet. An extension cord should
not be used with this unit.
8
allows the intermittent use of an air tool
with an air requirement higher than the
compressor’s rated delivery.
ASME Safety Valve
A safety valve that automatically releases
the air if the air receiver (tank) pressure
exceeds the preset maximum.
Volts or Voltage
A measurement of the force of an electrical current.
PSI (Pounds per Square Inch)
Measurement of the pressure exerted by
the force of the air. The actual psi output
is measured by a pressure gauge on the
compressor
Amps or Amperage
A measure of the electrical force minus
the resistance on an electrical line.
Ridgid air compressors require 15 amps
for operation. Be sure the compressor
will operate on an electrical line with the
proper amps. If other appliances operate
on the same line, they will reduce the
available amps. If the amperage is not
adequate, the result will be blown fuses
or tripped circuits.
SCFM (Standard Cubic Feet per
Minute)
Sometimes called CFM (Cubic Feet per
Minute). Measurement of air volume
delivered by the compressor.
Air Delivery
A combination of psi and SCFM. The air
delivery required by a tool is stated as
(number) SCFM at (number) psi. The
combination of these figures determines
what size unit is needed.
Regulator
A control that adjusts the line pressure to
the proper amount needed to operate
spray guns and air tools.
Air Tank Capacity
The volume of air stored in the tank and
available for immediate use. A large tank
Tanks Pressure Gauge
Indicates tank pressure in psi.
9
Glossary of Terms (Continued)
Getting to Know Your Air Compressor
Line Pressure Gauge
Displays the current line pressures. It is
regulated by the regulator knob.
3
2
Cut-in/Cut-off Pressure
Specific psi at which a compressor starts
and stops while refilling the air tank.
1
4
Handle
Regulator
Knob
Regulated
Outlet Gauge
5
Air Storage
Tanks
Tank Pressure
Gauge
Unpacking and Checking Contents
1. Remove the air compressor from the
carton.
!
2. Place the compressor on a secure,
stationary work surface and look it
over carefully.
!
WARNING:
6
For your own safety, never
operate unit until all assembly
steps are complete and until
you have read and understood
the entire operator’s manual.
WARNING:
Do not operate unit if damaged
during shipping, handling or
use. Damage may result in
bursting and cause injury or
property damage.
!
7
Safety Valve
Air Outlet
Fittings
WARNING:
To reduce the risk of injury, if
any parts are missing, do not
attempt to operate the air compressor until the missing parts
are obtained and installed correctly.
9
8
On/Off Switch
Air Filter
Installation
1. Check and tighten all bolts, fittings,
etc., before operating compressor.
2. Operate compressor in a ventilated
area so that compressor may be
properly cooled.
4. To avoid loss of power and overheating, additional air hose must be used
to reach work area instead of extension cords.
3. Compressor should be located where
it can be directly plugged into an outlet. An extension cord should not be
used with this unit.
10
10
11
Tank Drain Valve
Getting to Know Your Air
Compressor (Continued)
1. Air Storage Tanks. The tanks store
air for later use.
2. Regulated Outlet Gauge. This gauge
shows at-a-glance, air pressure at
outlet. Air pressure is measured in
pounds per square inch (PSI). Most
tools have maximum pressure ratings.
Never exceed the maximum pressure
rating of the tool you are using. Be
sure this gauge reads ZERO before
changing air tools or disconnecting
hose from outlet.
Operating Your Air Compressor
Moisture in Compressed Air
6. ASME Safety Valve. This valve automatically releases air if the tank pressure exceeds the preset maximum.
Close
Open
IMPORTANT: This condensation will
cause water spots in a paint job, especially when spraying other than water
based paints. If sandblasting, it will
cause the sand to cake and clog the gun,
rendering it ineffective.
A filter in the air line, located as near to
the gun as possible, will help eliminate
this moisture.
Operating Your Air Compressor
3. Handle. Used to move the compressor.
4. Regulator Knob. This knob controls
air pressure to an air operated tool or
paint spray gun. Turning the knob
clockwise increases air pressure at
the outlet. Turning counterclockwise
will lower air pressure at the outlet.
Fully counterclockwise will shut off the
flow of air completely.
Moisture in compressed air will form into
droplets as it comes from an air compressor pump. When humidity is high or
when a compressor is in continuous use
for an extended period of time, this moisture will collect in the tank. When using a
paint spray or sandblast gun, this water
will be carried from the tank through the
hose, and out of the gun as droplets
mixed with the spray material.
7. Air Outlet Fittings. These fittings are
1/4” universal-style quick connect fittings and allow rapid tool changes.
8. Air Filter. The air filter keeps dirt and
debris from entering the compressor
pump and reduces compressor noise.
9. On/Off Switch. This switch allows
manual control of the compressor.
Note that when the switch is turned
on, the compressor will automatically
start and stop depending on tank
pressure.
10. Tank Drain Valve. The tank drain
valve allows moisture to be removed
from the tank.
5. Tank Pressure Gauge. Gauge shows
pressure in air receiver indicating
compressor is building pressure properly.
Adjust the regulator knob to the desired
pressure.
Make sure the tank drain valve is closed,
the regulator knob is turned fully counterclockwise, and the On/Off switch is in the
OFF position.
Plug compressor into a dedicated 15
Amp (minimum) circuit.
Turn On/Off switch to the ON position.
The compressor will now start building
pressure.
After compressor reaches cut-off pressure, install a hose (with the desired air
tool attached) into the outlet fitting.
!
Do not over-pressurize any air
tool. Consult air tool instructions for proper air tool pressure.
The compressor is now ready to operate.
For Trouble-Free Operation
1. Read instructions: Carefully read
through this operator’s manual
BEFORE OPERATING the new air
compressor. It contains information
about operation and maintenance of
the unit.
sure to close tank drain valve tightly
before operating compressor.
3. Change air filter: Never run compressor without an air filter nor with a
clogged air filter. Replace with a new
filter when the element is dirty.
2. Drain tank daily: Depressurize system
prior to draining tank. Open tank
drain valve and drain moisture from
tank. This helps prevent tank corrosion and keeps oil and moisture out
of the compressed air system. Be
12
WARNING:
13
Maintenance
!
Tank
WARNING:
!
Release all pressure and disconnect power before making
any repair.
NOTICE:
DANGER:
Drain liquid from tank daily.
Never attempt to repair or modify a tank! Welding, drilling or
any other modification will
weaken the tank resulting in
damage from rupture or explosion. Always replace worn,
cracked or damaged tanks.
1. Check compressor for any visible
problems, especially check air filter to
be sure it is clean.
The tank should be carefully inspected at
a minimum of once a year. Look for
cracks forming near the welds. If a crack
is detected, remove pressure from tank
immediately and replace.
2. Pull ring on safety valve and allow it to
snap back to normal position.
!
Filter Removal, Inspection and Replacement
WARNING:
To change a filter, pull off the filter housing
cover. If filter element is dirty, replace element or entire filter.
Safety valve must be replaced if
it cannot be actuated or it leaks
air after ring is released.
Lubrication
3. Drain moisture from tank daily. Shut
compressor off. Depressurize system
prior to draining tank. Drain moisture
from tank by opening the tank drain
valve underneath the tank.
This is an oilless type compressor requiring no lubrication.
Storage
4. Turn power OFF and clean dust and
dirt from motor, tank, air lines and
pump cooling fins.
Tank
Drain
Valve
NOTE: The air filter in the filter housing
on the side of the head must be checked
and cleaned periodically, more often if
used under very dusty conditions or
when a great deal of fog from spraying is
allowed to circulate near unit.
1. When not in use, compressor should be 3. Hose should be disconnected and hung
stored in a cool dry place.
open ends down to allow any moisture
to drain.
2. Tank should be drained of moisture.
Maintenance Schedule
IMPORTANT: Unit should be located as
far from spraying area as hose will allow
to prevent over-spray from clogging filter.
14
Operation
Daily
Drain Tank
Weekly
Check Air Filter
Check Safety Valve
Blow Dirt From Inside Motor
15
Troubleshooting
!
TROUBLE
Thermal overload
protector cuts out
repeatedly
WARNING:
For your own safety do not try
and run the air compressor
while troubleshooting.
TROUBLE
Compressor will not
run
PROBABLE CAUSE
1. Unit is plugged into
extension cord
2. No electrical power
5. Thermal overload open
6. Pressure switch bad
Fuses blow/circuit
breaker trips repeatedly
1. Low voltage
2. Clogged air filter
3. Lack of proper ventilation/room temperature
too high
4. Unit is plugged into
extension cord
3. Blown fuse
4. Breaker open
Motor hums but cannot run or runs slowly
PROBABLE CAUSE
1. Remove extension cord
Air tank pressure
drops when compressor shuts off
2. Plugged in? Check
fuse/breaker or motor overload
3. Replace blown fuse
4. Reset, determining why
problem happened
5. Motor will restart when cool
6. Replace
1. Check with voltmeter
2. Remove extension cord
1. Incorrect size fuse, circuit
overloaded
1. Check for proper fuse, use
time-delay fuse.
Disconnect other electrical
appliances from circuit or
operate compressor on its
own branch circuit
2. Remove extension cord
16
1. Check with voltmeter
2. Clean filter (see
Maintenance section)
3. Move compressor to well
ventilated area
4. Remove extension cord
REMEDY
1. Low voltage
2. Unit is plugged into
extension cord
3. Shorted or open motor
winding
4. Defective check valve or
unloader
2. Unit is plugged into
extension cord
3. Defective check valve or
unloader
REMEDY
2. Loose drain lock
3. Check valve leaking
3. Replace or repair
1. Check all connections with
soap and water solution
and tighten
2. Tighten
3. Disassemble check valve
assembly, clean or replace
!
DANGER:
Do not disassemble
check valve with air in
tank; bleed tank
1. Excessive water in air
tank
2. High humidity
1. Drain tank
1. Defective pressure
switch
2. Excessive air usage
1. Replace switch
Compressor vibrates
Loose mounting bolts
Tighten
Air output lower than
normal
1. Broken inlet valves
1. Have authorized service
representative repair unit
2. Clean or replace intake filter
3. Tighten connections
Excessive moisture
in discharge air
3. Replace motor
4. Replace or repair
1. Loose connections (fittings, tubing, etc.)
Compressor runs
continuously
2. Intake filter dirty
3. Connections leaking
17
2. Move to area of less
humidity; use air line filter
2. Decrease air usage; compressor not large enough
for a requirement
Repair Parts
Repair Parts
For Repair Parts, Call 1-800-4-RIDGID
1
Please provide following information:
-Model number
-Serial number (if any)
-Part description and number as shown in parts list
2
40
41
3
4
5
39
4
38
4
8
6
9
7
6
To Pump Head
37
To Unloader
36
11
34
10
12
33
35
13
32
16
31
16
30
29
28
14
15
18
19
17
27
26
20
21
25
24
23
22
18
Ref.
Catalog
No.
Number
1
17698
2
17703
3
17708
4
17713
5
17718
6
17723
7
17728
8
17733
9
17738
10
17743
11
17748
12
17753
13
17758
14
17763
15
17878
16
17783
17
17793
18
17798
19
17808
20
17813
21
17838
22
17848
23
17853
24
17858
25
17863
26
17868
27
17873
28
17773
29
17883
30
17888
31
17893
32
17898
33
17903
34
17908
35
17913
36
17918
37
17923
38
17928
39
17933
40
17938
41
17943
REPAIR PARTS KITS
18713
Part
Number
WL373000AJ
WL012000AV
WL012300AV
ST158000AV
WL003202AV
WL003203AV
CV222203AJ
WL016200AP
ST039700AV
ST039800AV
ST117802AV
ST209800AV
CW209600AV
EC012600AV
GA016901AV
ST071626AV
WL024501AV
V-215106AV
ST185600AV
WL025900AV
WL025800AV
ST073276AV
ST158300AV
WL021400AV
ST074415AV
ST119704AV
HF203300AV
GA016900AV
CW210000AV
ST022500AV
ST119305AV
HF002401AV
CW211700AV
CW211300AJ
D-1403
ST073612AV
AR052700CG
ST129301AV
ST129302AV
WL012406AV
ST072224AV
Descriptons
Pump/motor assembly
Filter
Filter element
Shoulder bolt
Rubber bushing (Rear)
Rubber bushing (Front)
Check valve
Exhaust tube
Nut
Ferrule
1/4" Flexible tube
Strain relief screw
Strain relief
Cord
Tank gauge
1/4”-20 x 1/2” Screw
Regulator assy. (includes 15, 27 & 28)
165 psi Safety valve
Grip
Roll bar
Control panel bracket
Foot screw
Molded rubber bumper
3/8” Nylon tube
1/4”-20 x 1/2” Thread cutting screw
3/8” 90o Push to connect
Coupler
Outlet gauge
Unloader
Plug
3/8” Push to connect
Nipple
Pressure switch cover
Pressure switch
Tank drain valve
Plug
4.5 gal. twin tank
Shroud screw
Shroud screw
Shroud
Exhaust fitting
WL209308AJ
Exhaust tube kit (without check valve)
19
Qty
1
1
1
4
2
2
1
1
1
1
1
1
1
1
1
4
1
1
1
1
1
4
4
1
4
1
2
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
Repair Parts
Repair Parts
For Repair Parts, Call 1-800-4-RIDGID
Please provide following information:
-Model number
-Serial number (if any)
-Part description and number as shown in parts list
2
1
Ref.
No.
Catolog
Number
Part
Number
1
2
3
4
5
6
17948
—
—
—
17958
17963
WL010500AV
XA012100AV
MC302300AJ
4
7
—
5
8
9
10
11
12
13
14
—
—
—
17968
—
17973
17978
(Included
with piston
assembly,
Ref. No. 11)
WL210300AJ
XA010800AV
XA012001AV
14
13
3
12
11
REPAIR PARTS KITS
17953
17983
17988
10
9
Descriptons
1
1
M5 x .8 x 12 HHCS (L.H.)
Washer
Fan
Piston assembly (includes. #7)
Intake valve
Head gasket
Discharge valve gasket
1
1
1
1
1
1
1
WL602801AJ
WL201405AJ
WL209802AJ
Head bolt kit (set of 4)
Valve plate kit (Includes #2-5, 12-14)
Fan kit (includes #8-10)
6
8
7
20
Qty
Head
Head bolts
Exhaust valve
Valve plate
Cylinder gasket
Motor assembly (includes
eccentric/bearing assembly)
M5 x .8 x 20 HH cap screw
21
1
4
1
1
1
1
1
1
Notes
Notes
22
23
RIDGID“ AIR COMPRESSOR LIMITED THREE YEAR WARRANTY
This product is manufactured by Campbell Hausfeld. The trademark is licensed from
Ridgid, Inc. All warranty communications should be directed to RIDGID air compressor technical service at (toll free) 1-800-4-RIDGID.
WHAT IS COVERED UNDER THE LIMITED THREE YEAR WARRANTY
This warranty covers all defects in workmanship or materials in this RIDGID air compressor for the three-year period from the date of purchase. This warranty is specific to this air compressor. Warranties for other RIDGID products may vary.
Catalog No. OF45150
Model No. OF45150
Serial No. ___________
The model and serial numbers may be found on your
unit. You should record both model and serial number
in a safe place for future use.
HOW TO OBTAIN SERVICE
To obtain service for this RIDGID air compressor you must return it, freight prepaid,
to a service center authorized to repair RIDGID air compressors. You may obtain the
location of the service center nearest you by calling (toll free) 1-800-4-RIDGID or by
logging on to the RIDGID website at www.ridgid.com. When requesting warranty
service, you must present the proof of purchase documentation, which includes a
date of purchase. The authorized service center will repair any faulty workmanship,
and either repair or replace any defective part, at Campbell Hausfeld’s option at no
charge to you.
WHAT IS NOT COVERED
This warranty applies only to the original purchaser at retail and may not be transferred. This warranty does not cover normal wear and tear or any malfunction, failure or defect resulting from misuse, abuse, neglect, alteration, modification or repair
by other than a service center authorized to repair RIDGID branded air compressors.
Expendable materials, such as oil, filters, etc. are not covered by this warranty.
Gasoline engines and components are expressly excluded from coverage and you
must comply with the warranty given by the engine manufacturer, which is supplied
with the product. CAMPBELL HAUSFELD MAKES NO WARRANTIES,
REPRESENTATIONS OR PROMISES AS TO THE QUALITY OR PERFORMANCE OF ITS AIR COMPRESSORS OTHER THAN THOSE
SPECIFICALLY STATED IN THIS WARRANTY. RIDGID, INC. MAKES NO
WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED,
INCLUDING AS NOTED BELOW.
ADDITIONAL LIMITATIONS
To the extent permitted by applicable law, all implied warranties, including warranties
of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE, are disclaimed.
Any implied warranties, including warranties of merchantability or fitness for a particular purpose, that cannot be disclaimed under state law are limited to three years
from the date of purchase. Campbell Hausfeld is not responsible for direct, indirect,
incidental, special or consequential damages. Some states do not allow limitations
on how long an implied warranty lasts and/or do not allow the exclusion or limitation
of incidental or consequential damages, so the above limitations may not apply to
you. This warranty gives you specific legal rights, and you may also have other
rights, which vary from state to state.
QUESTIONS OR COMMENTS
CALL 1-800-4-RIDGID
www.ridgid.com
Please have your Model Number and Serial Number on hand when calling.
© 2004 RIDGID, INC.
Part No. IN610301AV 6/04
Form No. IN610301AV
Printed in U.S.A. 6/04
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement