user`s manual - Fitness Deals Online

user`s manual - Fitness Deals Online
Model No. PETL13012.0
Serial No.
Write the serial number in the space
above for reference.
USER’S MANUAL
Serial Number
Decal
CUSTOMER SERVICE
UNITED KINGDOM
Call: 08457 089 009
From Ireland: 053 92 36102
Website: www.iconsupport.eu
E-mail: [email protected]
Write:
ICON Health & Fitness, Ltd.
c/o HI Group PLC
Express Way
CASTLEFORD
WF10 5QJ
UNITED KINGDOM
AUSTRALIA
Call: 1800 993 770
E-mail: [email protected]
Write:
ICON Health & Fitness
PO Box 635
WINSTON HILLS NSW 2153
AUSTRALIA
CAUTION
Read all precautions and instructions in this manual before using
this equipment. Keep this manual
for future reference.
www.iconeurope.com
TABLE OF CONTENTS
WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
IMPORTANT PRECAUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
BEFORE YOU BEGIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
PART IDENTIFICATION CHART. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
THE CHEST HEART RATE MONITOR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
OPERATION AND ADJUSTMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
EXERCISE GUIDELINES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
PART LIST. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
EXPLODED DRAWING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
ORDERING REPLACEMENT PARTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
RECYCLING INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover
WARNING DECAL PLACEMENT
This drawing shows the locations of the warning decals. If a decal is missing or illegible,
call the telephone number on the front
cover of this manual and request a free
replacement decal. Apply the decal in the
location shown. Note: The decals may not be
shown at actual size.
PROFORM is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read
all important precautions and instructions in this manual and all warnings on your treadmill before
using your treadmill. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
12.When connecting the power cord (see page
16), plug the power cord into an earthed
circuit. No other appliance should be on the
same circuit. When replacing the fuse in the
power cord adapter, insert an ASTA-approved
BS1362, 13-amp fuse into the fuse carrier.
2. Before beginning any exercise program,
consult your physician. This is especially
important for persons over age 35 or persons
with pre-existing health problems.
13.If an extension cord is needed, use only a
3-conductor, 14-gauge (1 mm2) cord that is
no longer than 5 ft. (1.5 m).
3. Use the treadmill only as described in this
manual.
14.Keep the power cord away from heated
surfaces.
4. The treadmill is intended for home use only.
Do not use the treadmill in any commercial,
rental, or institutional setting.
15.Never move the walking belt while the power
is turned off. Do not operate the treadmill
if the power cord or plug is damaged, or if
the treadmill is not working properly. (See
TROUBLESHOOTING on page 26 if the treadmill is not working properly.)
5. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
6. Place the treadmill on a level surface, with
at least 8 ft. (2.4 m) of clearance behind it
and 2 ft. (0.6 m) on each side. Do not place
the treadmill on any surface that blocks air
openings. To protect the floor or carpet from
damage, place a mat under the treadmill.
16.Read, understand, and test the emergency
stop procedure before using the treadmill
(see HOW TO TURN ON THE POWER on
page 18).
17.Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
7. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
18.The treadmill is capable of high speeds.
Adjust the speed in small increments to
avoid sudden jumps in speed.
8. Keep children under age 12 and pets away
from the treadmill at all times.
9. The treadmill should be used only by persons weighing 330 lbs. (150 kg) or less.
19.The heart rate monitor is not a medical
device. Various factors, including the user’s
movement, may affect the accuracy of heart
rate readings. The heart rate monitor is
intended only as an exercise aid in determining heart rate trends in general.
10.Never allow more than one person on the
treadmill at a time.
11.Wear appropriate exercise clothes while
using the treadmill. Do not wear loose
clothes that could become caught in the
treadmill. Athletic support clothes are recommended for both men and women. Always
wear athletic shoes. Never use the treadmill
with bare feet, wearing only stockings, or in
sandals.
20.Never leave the treadmill unattended while
it is running. Always remove the key, press
the power switch into the off position (see
the drawing on page 5 for the location of the
power switch), and unplug the power cord
when the treadmill is not in use.
3
21.Do not attempt to move the treadmill until it
is properly assembled. (See ASSEMBLY on
page 7, and HOW TO FOLD AND MOVE THE
TREADMILL on page 25.) You must be able to
safely lift 45 lbs. (20 kg) to move the treadmill.
25.
22.When folding or moving the treadmill, make
sure that the storage latch is holding the
frame securely in the storage position.
23.Never insert any object into any opening on
the treadmill.
DANGER: Always unplug the power
cord immediately after use, before cleaning the treadmill, and before performing the
maintenance and adjustment procedures
described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service representative only.
26.Over exercising may result in serious injury
or death. If you feel faint or if you experience
pain while exercising, stop immediately and
cool down.
24.Inspect and properly tighten all parts of the
treadmill regularly.
SAVE THESE INSTRUCTIONS
4
BEFORE YOU BEGIN
Thank you for selecting the new PROFORM® 1350
ZLT treadmill. The 1350 ZLT treadmill provides an
impressive selection of features designed to make your
workouts at home more effective and enjoyable.
manual. To help us assist you, note the product model
number and serial number before contacting us. The
model number and the location of the serial number
decal are shown on the front cover of this manual.
For your benefit, read this manual carefully before
you use the treadmill. If you have questions after
reading this manual, please see the front cover of this
Before reading further, please familiarize yourself with
the parts that are labeled in the drawing below.
Length: 6 ft. (183 cm)
Width: 2 ft. 10 in. (86 cm)
Weight: 209 lbs. (95 kg)
Console
Accessory Tray
Handrail
Heart Rate Monitor
Key/Clip
Motor Hood
Walking Belt
Power Switch
Foot Rail
Wheel
Platform Cushion
Idler Roller
Adjustment Screws
5
PART IDENTIFICATION CHART
Use the drawings below to identify small parts used for assembly. The number in parentheses below each drawing is the key number of the part, from the PART LIST near the end of this manual. The number following the key
number is the quantity used for assembly. Note: If a part is not in the hardware kit, check to see if it is preattached. Extra parts may be included.
#10 Star
Washer (5)–4
5/16" Star
Washer (8)–4
3/8" Star
Washer (10)–6
#10 x 3/4"
Screw (4)–4
#8 x 1/2"
Screw (1)–14
3/8" Nut (9)–4
3/8" x 2" Bolt (2)–2
5/16" x 2 3/4" Screw (12)–4
3/8" x 2 1/2" Bolt (7)–2
3/8" x 4" Screw (3)–6
#8 x 3/4" Tek
Screw (13)–8
5/16" Flat
Washer (XX)–4
6
ASSEMBLY
• Assembly requires two persons.
• To identify small parts, see page 6.
• Place all parts in a cleared area and remove the
packing materials. Do not dispose of the packing
materials until you finish all assembly steps.
• Assembly requires the following tools:
the included hex keys
• After shipping, there may be an oily substance
on the exterior of the treadmill. This is normal. If
there is an oily substance on the treadmill, wipe
it off with a soft cloth and a mild, non-abrasive
cleaner.
one adjustable wrench
• Left parts are marked “L” or “Left” and right parts
are marked “R” or “Right.”
needlenose pliers
one Phillips screwdriver
scissors
To avoid damaging parts, do not use power tools.
1.
Go to www.iconsupport.eu on your computer
and register your product.
• activates your warranty
• saves you time if you ever need to contact
Customer Service
• allows us to notify you of upgrades and offers
1
Note: If you do not have Internet access, call
CUSTOMER SERVICE (see the front cover of
this manual) and register your product.
2.
Make sure that the power cord is unplugged.
2
Locate the Upright Wire (91) bundled around the
front of the Base (29). Cut the plastic tie securing
the Upright Wire. Route the Upright Wire out of
the indicated hole.
See the inset drawing. Cut the plastic tie near
the Upright Wire (91). Be careful not to damage the Upright Wire.
29
91
Cut
Hole
Tie
Cut
91
7
3.Press a Base Cap (87) into each side of the
Base (29).
3
87
29
87
4.Identify the Left Upright (84). Have a second
person hold the Left Upright near the Base (29).
4
84
See the inset drawing. Tie the wire tie in the
Left Upright (84) securely around the end of the
Upright Wire (91). Then, insert the Upright Wire
into the lower end of the Left Upright as you pull
the other end of the wire tie through the Left
Upright.
Wire
Tie
91
91
Wire
Tie
84
29
5.Hold the Left Upright (84) against the Base (29).
Be careful not to pinch the wires. Partially
tighten three 3/8" x 4" Screws (3) with three
3/8" Star Washers (10) into the Left Upright and
Base; do not fully tighten the Screws yet.
5
84
10
3
Wires
29
8
6.Hold the Right Upright (85) against the Base
(29). Partially tighten three 3/8" x 4" Screws (3)
with three 3/8" Star Washers (10) into the Right
Upright and the Base; do not fully tighten the
Screws yet.
6
85
10
29
3
7. Identify the Left and Right Base Covers (88, 89).
Slide the Left and Right Base Covers onto the
Left and Right Uprights (84, 85) as shown.
7
85
84
88
9
89
8.Identify the left handrail assembly (A). If there is
a wire in the left handrail assembly, remove and
discard it.
8
12
79
Hold the left handrail assembly (A) near the Left
Upright (84). Insert the wire tie on the Upright
Wire (91) into the bottom and out of the end of
the left Handrail (79) as shown. Then, pull the
Upright Wire through the Left Handrail.
8
91
B
A
Wire
Tie
Attach the left Handrail (79) to the Left Upright
(84) with two 5/16" x 2 3/4" Screws (12) and two
5/16" Star Washers (8). Make sure not to pinch
the Upright Wire (91). Start both Screws, but
do not tighten them yet.
84
Remove and discard the two indicated screws
(B) from the left Handrail (79).
9.Attach the right Handrail (79) to the Right Upright
(85) with two 5/16" x 2 3/4" Screws (12) and two
5/16" Star Washers (8). Start both Screws, but
do not tighten them yet.
9
12
Remove and discard the two indicated screws
(B) from the right Handrail (79).
8
79
B
85
10
10.Set the Console Base (98) face down on a soft
surface to avoid scratching the Console Base.
10
11
Remove the two screws (C) from the Pulse
Crossbar (81). Remove the Pulse Crossbar and
discard the screws.
101
98
Remove the four 5/16" x 5/8" Screws (11) from
the Console Frame (101). The Screws will be
used in a later step.
C
11
81
11.Identify the Left and Right Trays (95, 96).
11
Attach the Trays (95, 96) to the Console Base
(98) with eight #8 x 1/2" Screws (1). Note: It may
be easier to start the two inside Screws and then
slide the Trays into place before tightening the
other six Screws.
101
96
1
1
95
Note: It may be necessary to rotate the Console
Frame (101) upward when attaching the Trays
(95, 96).
98
1
1
11
1
12.IMPORTANT: To avoid damaging the Pulse
Crossbar (81), do not use power tools and do
not overtighten the #10 x 3/4" Screws (4).
12
4
79
Orient the Pulse Crossbar (81) as shown. Attach
the Pulse Crossbar to the Handrails (79) with
four #10 x 3/4" Screws (4) and four #10 Star
Washers (5). Start all four Screws, and then
tighten them.
91
Make sure that the Upright Wire (91) isn’t
pinched. Firmly tighten the four 5/16" x 2 3/4"
Screws (12).
5
12
4
81
5
79
12
13.With the help of a second person, hold the console assembly near the Handrails (79) (only one
is shown).
13
Console
Assembly
Connect the ground wire from the console
assembly to the Ground Wire (80) on the Pulse
Crossbar (81).
Connect the Upright Wire (91) to the console
wire. See the inset drawing. The connectors
should slide together easily and snap into
place. If they do not, turn one connector and try
again. IF YOU DO NOT CONNECT THE CONNECTORS PROPERLY, THE CONSOLE MAY
BECOME DAMAGED WHEN YOU TURN ON
THE POWER. Then, remove the wire tie from
the Upright Wire.
Ground
Wire
Console
Wire
91
80
Console
Wire
91
12
81
Wire
Tie
79
14.Set the console assembly on the Handrails (79).
Make sure that no wires are pinched. Insert
the excess Upright Wire (91) behind the Console
Frame (101).
14
Console
Assembly
101
Attach the console assembly to the brackets
on the Handrails (79) with the four 5/16" x 5/8"
Screws (11) that you removed in step 10. Start
all four Screws, but do not tighten them yet.
91
79
79
11
11
15.Attach the Pulse Crossbar (81) to the console
assembly with six #8 x 1/2" Screws (1). Start all
six Screws, and then tighten them.
15
Console
Assembly
Firmly tighten the four 5/16" x 5/8" Screws (11).
11
11
81
1
16.Tighten all six 3/8" x 4" Screws (3).
1
1
16
3
3
13
17.Raise the Frame (57) to the position shown.
Have a second person hold the Frame until
this step is completed.
17
Orient the Storage Latch (54) so that the large
barrel and the latch knob are oriented as shown.
57
Remove any ties from the end of the Storage
Latch (54). Attach the lower end of the Storage
Latch to the Base (29) with a 3/8" x 2" Bolt (2)
and a 3/8" Nut (9).
9
2
Attach the upper end of the Storage Latch (54)
to the Frame (57) with a 3/8" x 2" Bolt (2) and a
3/8" Nut (9).
54
Large
Barrel
Latch
Knob
29
18.Attach a Wheel (93) to the Base (29) with a 3/8"
x 2 1/2" Bolt (7) and a 3/8" Nut (9). Do not overtighten the Nut; the Wheel must turn freely.
18
9
2
57
Attach the other Wheel (93) to the other side
of the Base (29) in the same way.
See HOW TO FOLD THE TREADMILL on page
25. Lower the Frame (57) to the floor.
7
29
93
9
9
93
7
19.Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of plastic
on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the treadmill.
Note: Extra parts may be included. Keep the included hex key in a secure place; the hex key is used to adjust
the walking belt (see pages 27 and 28).
14
THE CHEST HEART RATE MONITOR
HOW TO PUT ON THE HEART RATE MONITOR
The heart rate
monitor consists of
a chest strap and a
sensor. Insert the
tab on one end of
the chest strap into
the hole in one end
of the sensor as
shown. Then, press
the end of the sensor under the buckle
on the chest strap.
The tab should be
flush with the front of
the sensor.
Tabs
• Do not expose the heart rate monitor to direct sunlight for extended periods of time; do not expose it
to temperatures above 122° F (50° C) or below 14°
F (-10° C).
Chest
Strap
• Do not excessively bend or stretch the sensor when
using or storing the heart rate monitor.
Sensor
• To clean the sensor, use a damp cloth and a small
amount of mild soap. Then, wipe the sensor with a
damp cloth and thoroughly dry it with a soft towel.
Never use alcohol, abrasives, or chemicals to clean
the sensor. Hand wash and air dry the chest strap.
Tab
Sensor Buckle
The heart rate monitor must be worn
under your clothes,
tight against your
skin. Wrap the heart
rate monitor around
your chest in the
location shown.
Make sure that
the logo is rightside-up. Then, attach the other end of the chest strap
to the sensor. Adjust the length of the chest strap, if
necessary.
TROUBLESHOOTING
If the heart rate monitor does not function properly, try
the steps below.
• Make sure that you are wearing the heart rate monitor as described at the left. If the heart rate monitor
does not function when positioned as described,
move it slightly lower or higher on your chest.
• If heart rate readings are not displayed until you
begin perspiring, rewet the electrode areas.
• For the console to display heart rate readings, you
must be within arm’s length of the console.
• If there is a battery cover on the back of the sensor,
replace the battery with a new battery of the same
type.
Pull the sensor away from your body a few inches and
locate the two electrode areas, which are covered by
shallow ridges. Using saline solution such as saliva or
contact lens solution, wet the electrode areas. Then,
return the sensor to a position against your chest.
• The heart rate monitor is designed to work with
people who have normal heart rhythms. Heart rate
reading problems may be caused by medical conditions such as premature ventricular contractions
(pvcs), tachycardia bursts, and arrhythmia.
CARE AND MAINTENANCE
• The operation of the heart rate monitor can be
affected by magnetic interference from high power
lines or other sources. If you suspect that magnetic
interference is causing a problem, try relocating the
fitness equipment.
• Thoroughly dry the sensor with a soft towel after
each use. Moisture may keep the sensor activated,
shortening the life of the battery.
• Store the heart rate monitor in a warm, dry place.
Do not store the heart rate monitor in a plastic bag
or other container that may trap moisture.
15
SP
OPERATION AND ADJUSTMENT
HOW TO PLUG IN THE POWER CORD
Follow the steps below to plug in the power cord.
This product must be earthed. If it should malfunction or break down, earthing provides a path of least
resistance for electric current to reduce the risk of
electric shock. This product’s power cord has an
equipment-earthing conductor and an earthing plug.
IMPORTANT: If the power cord is damaged, it must
be replaced with a manufacturer-recommended
power cord.
1. Plug the indicated end of the power cord into the
socket on the treadmill.
Socket on Treadmill
AUS
DANGER:
Improper connection of
the equipment-earthing conductor can result
in an increased risk of electric shock. Check
with a qualified electrician or serviceman if
you are in doubt as to whether the product
is properly earthed. Do not modify the plug
provided with the product—if it will not fit
the outlet, have a proper outlet installed by a
qualified electrician.
Power Cord
2. Plug the power cord into an appropriate outlet that
is properly installed and earthed in accordance with
all local codes and ordinances.
Australia
UK
Outlet
GR
Outlet
UK
AUS
FR/SP
GR
RU
16HU
GR
RU
HU
CONSOLE DIAGRAM
FEATURES OF THE CONSOLE
You can even listen to your favorite workout music or
audio books with the console’s stereo sound system
while you exercise.
The treadmill console offers an impressive array of
features designed to make your workouts more effective and enjoyable. When you use the manual mode,
you can change the speed and incline of the treadmill
with the touch of a button. As you exercise, the console
will display instant exercise feedback. You can even
measure your heart rate using the handgrip heart rate
monitor.
To turn on the power, see page 18. To use the manual mode, see page 18. To use an onboard workout,
see page 21. To use a set-a-goal workout, see page
22. To use an iFit workout, see page 22. To use the
stereo sound system, see page 23. To use the information mode, see page 24.
In addition, the console features twenty-four onboard
workouts—six calorie workouts, six incline workouts,
six intensity workouts, and six speed workouts. Each
workout automatically controls the speed and incline of
the treadmill as it guides you through an effective exercise session.
Note: The console can display speed and distance in
either miles or kilometers. To find which unit of measurement is selected, see THE INFORMATION MODE
on page 24. For simplicity, all instructions in this section refer to kilometers.
IMPORTANT: If there are sheets of plastic on the
console, remove the plastic. To prevent damage
to the walking platform, wear clean athletic shoes
while using the treadmill. The first time you use
the treadmill, observe the alignment of the walking
belt, and center the walking belt if necessary (see
page 28).
The console also features an iFit mode that enables
the treadmill to communicate with your wireless
network through an optional iFit module. With the
iFit mode, you can download personalized workouts,
create your own workouts, track your workout results,
race against other iFit users, and access many other
features. To purchase an iFit module at any time, go
to www.iFit.com or call the telephone number on
the front cover of this manual.
ETNE12812
(NETL12812 )
17
HOW TO TURN ON THE POWER
HOW TO USE THE MANUAL MODE
IMPORTANT: If the treadmill has been exposed to
cold temperatures, allow it to warm to room temperature before turning on the power. If you do not
do this, you may damage the console displays or
other electrical components.
1.Insert the key into the console.
Plug in the power cord (see
page 16). Next, locate the
power switch on the treadmill frame near the power
cord. Press the power
switch into the reset
position.
If the manual mode is not selected, press the
Manual button to select the manual mode.
See HOW TO TURN ON THE POWER at the left.
2.Select the manual mode.
3. Start the walking belt.
Reset
To start the walking belt, press the Start button, the
Speed increase button, or one of the KM/H buttons
numbered 2 through 20.
IMPORTANT: The console features a display demo
mode, designed to be used if the treadmill is displayed in a store. If the displays light as soon as
you plug in the power cord and press the power
switch into the reset position, the demo mode is
turned on. To turn off the demo mode, hold down
the Stop button for a few seconds. If the displays
remain lit, see THE INFORMATION MODE on page
24 to turn off the demo mode.
If you press the Start button or the Speed increase
button, the walking belt will begin to move at 2
Km/H. As you exercise, change the speed of the
walking belt as desired by pressing the Speed
increase and decrease buttons. Each time you
press one of the buttons, the speed setting will
change by 0.1 Km/H; if you hold down the button,
the speed setting will change in increments of 0.5
Km/H. Note: After you press the button, it may take
a moment for the walking belt to reach the selected
speed setting.
Next, stand on the foot
rails of the treadmill. Find
Key
the clip attached to the key
and
slide the clip onto the
Clip
ETNE12812
waistband
of your
clothes.
(NETL12812
)
Then, insert the key into the
console. After a moment,
the displays will light.
IMPORTANT: In an emergency, the key can be pulled from the console,
causing the walking belt to slow to a stop. Test the
clip by carefully taking a few steps backward; if the
key is not pulled from the console, adjust the position of the clip.
If you press one of the numbered KM/H buttons,
the walking belt will gradually change speed until it
reaches the selected speed setting.
To stop the walking belt, press the Stop button.
The time will begin to flash in the display. To restart
the walking belt, press the Start button or the
Speed increase button.
18
4. Change the incline of the treadmill as desired.
The My Trail tab will show a track that represents
400 m (1/4 mile). As you exercise, the white rectangle will show your progress. The My Trail tab will
also show the number of laps you complete.
To change the incline of the treadmill, press the
Incline increase or decrease button or one of the
numbered % Grade buttons. Each time you press
one of the buttons, the treadmill will gradually
adjust to the selected incline setting.
The Calorie tab will show the approximate amount
of calories you have burned. The height of each
segment represents the amount of calories burned
during that segment.
5.Follow your progress with the displays.
As you walk or run on the treadmill, the display can
show the following workout information:
• The elapsed time
• The distance that you have walked or run
• The workout intensity bar
• The approximate number of calories you have
burned
• The incline level of the treadmill
• The number of vertical feet you have climbed
• The speed of the walking belt
• Your heart rate (see step 6 on page 20)
• The matrix
As you exercise, the workout intensity level bar will
indicate the approximate intensity level of your
exercise.
E
(N
Press the Home button to return to the default
menu (see THE INFORMATION MODE on page
24 to set the default menu). If necessary, press the
Home button again.
When a wireless iFit module
is connected, the wireless
symbol at the top of the display will show the strength
of your wireless signal.
Four arcs indicate full signal
strength.
The matrix offers several display tabs. Press the
increase and decrease button next to the Enter button until the desired tab is shown.
To reset the displays, press the Stop button, remove the key, and then reinsert the key.
he Incline tab will show a profile of the incline setT
tings of the workout. A new segment will appear at
the end of each minute. The Speed tab will show a
profile of the speed settings of the workout.
19
6. Measure your heart rate if desired.
7. Turn on the fan if desired.
Before using
the handgrip
heart rate monitor, remove the
sheets of plastic
from the metal
contacts on the
pulse bar. In addition, make sure
that your hands
are clean.
The fan features multiple speed settings.
Press the fan increase
and decrease buttons
repeatedly to select a fan speed or to turn off the
fan.
8.When you are finished exercising, remove the
key from the console.
Contacts
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting or you may damage the treadmill when you
fold it to the storage position. Next, remove the
key from the console and put it in a secure place.
To measure your heart rate, stand on the foot
rails and hold the pulse bar with your palms on
the metal contacts for approximately ten seconds;
avoid moving your hands. When your pulse is
detected, a heart symbol in the calorie display
will flash each time your heart beats, one or two
dashes will appear, and then your heart rate will be
shown. For the most accurate heart rate reading, continue to hold the contacts for about 15
seconds.
20
hen you are finished using the treadmill, press
W
the power switch into the off position and unplug
the power cord. IMPORTANT: If you do not do
this, the treadmill’s electrical components may
wear prematurely.
HOW TO USE AN ONBOARD WORKOUT
The workout will continue in this way until the last
segment of the profile flashes in the display and the
last segment ends. The walking belt will then slow
to a stop.
1.Insert the key into the console.
See HOW TO TURN ON THE POWER on page 18.
Note: The calorie goal is an estimate of the
number of calories that you will burn during
the workout. The actual number of calories
that you burn will depend on various factors
such as your weight. In addition, if you manually change the speed or incline of the treadmill
during the workout, the number of calories you
burn will be affected.
2. Select an onboard workout.
To select an onboard workout, press the Calorie
button, the Incline button, the Intensity button, or
the Speed button repeatedly until the desired workout appears in the display.
When you select an onboard workout, the lower
display will show the duration of the workout and
the name of the workout. The upper display will
show the duration and distance of the workout. In
addition, a profile of the speed settings of the workout will appear in the matrix. If you select a calorie
workout, the approximate number of calories you
will burn will appear in the name of the workout.
If the speed or incline setting is too high or too low
at any time during the workout, you can manually override the setting by pressing the Speed or
Incline buttons; however, when the next segment
of the workout begins, the treadmill will automatically adjust to the speed and incline settings for the next segment.
3. Start the workout.
To stop the workout at any time, press the Stop
button. The time will begin to flash in the display.
To resume the workout, press the Start button or
the Speed increase button. The walking belt will
begin to move at 2 Km/H. When the next segment
of the workout begins, the treadmill will automatically adjust to the speed and incline settings for the
next segment.
ress the Start button or the Speed increase button
P
to start the workout. A moment after you press the
button, the treadmill will automatically adjust to the
first speed and incline settings of the workout. Hold
the handrails and begin walking.
Each workout is divided into segments. One speed
setting and one incline setting are programmed for
each segment. Note: The same speed setting and/
or incline setting may be programmed for consecutive segments.
4. Follow your progress with the displays.
See step 5 on page 19. The display will show
the time remaining in the workout instead of the
elapsed time.
During the
workout, the
profiles on
the speed
and incline
Current Segment
tabs will
show your
progress.
The flashing segment of the profile represents the
current segment of the workout. The height of the
flashing segment indicates the approximate speed
or incline setting for the current segment. At the
end of each segment, a series of tones will sound
and the next segment of the profile will begin to
flash. If a different speed and/or incline setting is
programmed for the next segment, the treadmill
will automatically adjust to the new speed and/or
incline setting.
5. Measure your heart rate if desired.
See step 6 on page 20.
6. Turn on the fan if desired.
See step 7 on page 20.
7. W
hen you are finished exercising, remove the
key from the console.
21
See step 8 on page 20.
HOW TO USE A SET-A-GOAL WORKOUT
6. Turn on the fan if desired.
1. Insert the key into the console.
See HOW TO TURN ON THE POWER on page 18.
7.When you are finished exercising, remove the
key from the console.
2. Select a set-a-goal workout.
To select a set-a-goal workout, press the Set A
Goal button on the console.
See step 7 on page 20.
See step 8 on page 20.
HOW TO USE AN IFIT WORKOUT
Use the increase and decrease buttons next to
the Enter button to set a calorie, time, or distance
goal, and then press the Enter button. Next, press
the increase and decrease buttons next to the
Enter button to select a goal. Press the Speed and
Incline buttons to select the speed and incline for
the workout. The screen will show the duration and
distance of the workout, and the approximate number of calories you will burn during the workout.
Note: To use an iFit workout, you must have access to
a computer with a USB port and an internet connection. In addition, you must have access to a wireless
network including an 802.11b/g/n router with SSID
broadcast enabled (hidden networks are not supported). An iFit.com membership is also required.
1.Insert the key into the console.
3. Start the workout.
See HOW TO TURN ON THE POWER on page 18.
Press the Start button to start the workout. A
moment after you press the button, the walking belt
will begin to move. Hold the handrails and begin
walking.
2. Insert the iFit module into the console.
The workout will function in the same way as the
manual mode (see pages 18 to 20).
IMPORTANT: To satisfy exposure compliance
requirements, the antenna and transmitter in
the iFit module must be at least 8 in. (20 cm)
from all persons and must not be near or connected to any other antenna or transmitter.
To insert the iFit module, see the instructions
included with the iFit module.
The workout will continue until you reach the goal
that you set. The walking belt will then slow to a
stop.
3. Select a user.
Note: The calorie goal is an estimate of the
number of calories that you will burn during the
workout. The actual number of calories that you
burn will depend on various factors such as
your weight.
If more than one user is registered, you can switch
users in the iFit main screen. Press the increase
and decrease buttons next to the Enter button to
select a user.
4. Follow your progress with the displays.
4. Select an iFit workout.
To select an iFit workout, press one of the iFit
buttons. Before some workouts will download, you
must add them to your schedule on www.iFit.com.
See step 5 on page 19.
5. Measure your heart rate if desired.
See step 6 on page 20.
22
Press the Map button, the Train button, or the Lose
Wt. button to download the next workout of that
type in your schedule. Press the Compete button to
compete in a race that you have previously
scheduled.
6.Follow your progress with the displays.
To re-run a recent iFit workout from your schedule,
first press the Track button. Next, press the increase and decrease buttons to select the desired
workout. Then, press the Enter button to start the
workout.
See step 6 on page 20.
Note: If there are no workouts of the selected type
in your schedule, the next workout in your schedule
will be downloaded.
9.When you are finished exercising, remove the
key from the console.
See step 5 on page 19.
7. Measure your heart rate if desired.
8.Turn on the fan if desired.
See step 7 on page 20.
For more information on the iFit workouts,
please see www.iFit.com.
For more information about the iFit mode, go to
www.iFit.com.
When you select an iFit workout, the display will
show the duration of the workout, the distance you
will walk or run, the approximate number of calories
you will burn, the name of the workout, and the
maximum speed and incline settings. If you select a
competition workout, the display will count down to
the beginning of the race.
HOW TO USE THE STEREO SOUND SYSTEM
To play music or audio books through the console’s
stereo speakers, you must connect your MP3 player,
CD player, or other personal audio player to the console through the MP3 jack.
Note: Some of the iFit buttons can also run two
demo workouts. To use the demo workouts,
remove the iFit module from the console and press
one of the iFit buttons.
To use the MP3 jack, plug your audio wire into the MP3
jack. Then, plug your audio wire into a jack on your
MP3 player, CD player, or other personal audio player.
Make sure that your audio wire is fully inserted.
5. Start the workout.
See step 8 on page 20.
Next, press the play button
on your MP3 player, CD
player, or other personal
audio player. Adjust the volume on your personal audio
player or press the volume
increase and decrease buttons on the console.
See step 3 on page 21.
During some workouts, the voice of a personal
trainer will guide you through your workout. You
can select a setting for the personal trainer (see
THE INFORMATION MODE on page 24).
To stop the workout at any time, press the Stop
button. The time will begin to flash in the display.
To resume the workout, press the Start button or
the Speed increase button. The walking belt will
begin to move at the speed setting for the first
segment of the workout. When the next segment of
the workout begins, the treadmill will automatically
adjust to the speed and incline settings for the next
segment.
Decrease
Increase
If you are using a personal CD player and the CD
skips, set the CD player on the floor or another flat surface instead of on the console.
23
THE INFORMATION MODE
into the reset position, and insert the key into the
console. However, when you remove the key, the
displays will remain lit, although the buttons will not
function. If the demo mode is turned on, the word
ON will appear in the matrix. To turn on or turn off
the demo mode, press the Enter button.
The console features an information mode that keeps
track of treadmill information and allows you to personalize console settings.
1. Select the information mode.
CONTRAST LVL—Press the Incline increase and
decrease buttons to adjust the contrast level of the
display.
To select the information mode, hold down the Stop
button while inserting the key into the console and
then release the Stop button. When the information
mode is selected, the following information will be
shown:
If a module is connected, you may also select
the following screen:
The time display will show the total number of
hours that the treadmill has been used.
TRAINER VOICE—To turn on or turn off the voice
of the personal trainer, press the Enter button.
The distance display will show the total number
of kilometers (or miles) that the walking belt has
moved.
If an iFit module is connected, you may also select the following screens:
DEFAULT MENU—The default menu will appear
when you insert the key into the console or when
you press the Home button. Press the Enter button
repeatedly to select the manual main screen or the
iFit screen as the default menu.
The lower section of the display will show the
status of an iFit module. If an iFit module is connected, the display will show the words WIFI
MODULE. If a USB module is connected, the
display will show the words USB/SD MODULE. If
no module is connected, the display will show the
words NO IFIT MODULE.
CHECK WIFI STATUS—Press the Enter button
to check the status of your iFit module. The lower
display will show the software version number, the
network SSID, the network encryption type, the
connection status, the wireless signal strength, the
IP address of the module, the number of registered
users and their names, the results of the DNS
lookup, and the status of the iFit server.
2. Select the optional screens.
While the information mode is selected, the matrix
will display several optional screens. Press the
decrease button next to the Enter button to select
each of the following screens:
SEND/RECEIVE DATA—To send and receive
workouts, workout logs, and updates, press the
Enter button. When the process is finished, the
words TRANSFERS DONE will appear in the
display.
UNITS—To change the unit of measurement, press
the Enter button. To view distance in miles, select
ENGLISH. To view distance in kilometers, select
METRIC.
DEMO—The console features a display demo
mode, designed to be used if the treadmill is displayed in a store. While the demo mode is turned
on, the console will function normally when you
plug in the power cord, press the power switch
3. Exit the information mode.
To exit the information mode, remove the key from
the console.
24
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL
HOW TO MOVE THE TREADMILL
To avoid damaging the treadmill, adjust the incline
to the lowest position before you fold the treadmill.
Then, remove the key and unplug the power cord.
CAUTION: You must be able to safely lift 45 lbs. (20
kg) to raise, lower, or move the treadmill.
efore moving the treadmill, fold it as described at the
B
left. CAUTION: Make sure that the latch knob is
locked in the storage position. Moving the treadmill
may require two people.
1. Hold the frame and one of the handrails, and place
one foot against a wheel.
1. Hold the metal frame firmly in the location shown
by the arrow below. CAUTION: Do not hold the
frame by the plastic foot rails. Bend your legs
and keep your back straight.
1
Frame
1
Handrail
Frame
Wheel
2. Pull back on the handrail until the treadmill will roll
on the wheels, and carefully move it to the desired
location. CAUTION: Do not move the treadmill
without tipping it back, do not pull on the frame,
and do not move the treadmill over an uneven
surface.
2.Raise the frame until the latch knob locks in the
storage position. CAUTION: Make sure that the
latch knob locks.
2
3. Place one foot against a wheel, and carefully lower
the treadmill.
Frame
HOW TO LOWER THE TREADMILL FOR USE
1.
See drawing 2. Hold the upper end of the treadmill
with your right hand. Then, pull the latch knob to
the left and hold it. IMPORTANT: Do not turn the
latch knob. If necessary, push the frame forward
slightly. Pivot the frame downward a few inches,
and release the latch knob.
Latch
Knob
2.
See drawing 1 at the left. Hold the metal frame
firmly with both hands, and lower it to the floor.
CAUTION: Do not hold the frame by the plastic
foot rails, and do not drop the frame. Bend your
legs and keep your back straight.
o protect the floor or carpet, place a mat under the
T
treadmill. Keep the treadmill out of direct sunlight. Do
not leave the treadmill in the storage position in temperatures above 85° F (30° C).
25
TROUBLESHOOTING
Most treadmill problems can be solved by following the simple steps below. Find the symptom that
applies, and follow the steps listed. If further assistance is needed, see the front cover of this manual.
c.Remove the key from the console, and then
reinsert it.
d.If the treadmill still will not run, please see the front
cover of this manual.
SYMPTOM: The power does not turn on
SYMPTOM: The console displays remain lit when
you remove the key from the console
a.Make sure that the power cord is plugged into a
surge suppressor and that the surge suppressor
is plugged into a properly grounded outlet (see
page 16). Use only a surge suppressor that meets
all of the specifications described on page 16.
IMPORTANT: The treadmill is not compatible
with GFCI-equipped outlets and may not be
compatible with AFCI-equipped outlets.
a.The console features a display demo mode,
designed to be used if the treadmill is displayed in
a store. If the displays remain lit when you remove
the key, the demo mode is turned on. To turn off
the demo mode, hold down the Stop button for a
few seconds. If the displays are still lit, see THE
INFORMATION MODE on page 24 to turn off the
demo mode.
b.After the power cord has been plugged in, make
sure that the key is inserted into the console.
SYMPTOM: The displays of the console do not
function properly
c.Check the power switch located on the treadmill
frame near the power cord. If the switch protrudes
as shown, the switch has tripped. To reset the
power switch, wait for five minutes and then press
the switch back in.
a.Remove the key from the console and UNPLUG
THE POWER CORD.
c
Tripped
emove the five #8 x 3/4" Screws (15). Carefully
R
slide the Motor Hood (65) off.
Reset
65
15
15
15
SYMPTOM: The power turns off during use
a.Check the power switch (see the drawing above).
If the switch has tripped, wait for five minutes and
then press the switch back in.
15
b.Make sure that the power cord is plugged in. If the
power cord is plugged in, unplug it, wait for five
minutes, and then plug it back in.
26
Locate the Reed Switch (52) and the Magnet (51)
on the left side of the Pulley (50). Turn the Pulley
until the Magnet is aligned with the Reed Switch.
Make sure that the gap between the Magnet and
the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the #8 x 3/4" Tek Screw (13), move
the Reed Switch slightly, and then retighten the
Screw. Reattach the Motor Hood (not shown) with
the five #8 x 3/4" Screws (not shown) and run the
treadmill for a few minutes to check for a correct
speed reading.
b.If the walking belt is overtightened, treadmill performance may decrease and the walking belt may
become damaged. Remove the key and UNPLUG
THE POWER CORD. Using the hex key, turn both
idler roller screws counterclockwise, 1/4 of a turn.
When the walking belt is properly tightened, you
should be able to lift each edge of the walking belt
2 to 3 in. (5 to 7 cm) off the walking platform. Be
careful to keep the walking belt centered. Then,
plug in the power cord, insert the key, and run the
treadmill for a few minutes. Repeat until the walking belt is properly tightened.
Top
View
b
52
13
51
50
2–3 in.
1/8 in.
Idler Roller Screws
SYMPTOM: The incline of the treadmill does not
change correctly
a. Hold down the Stop button and the Speed increase
button, insert the key into the console, and then
release the Stop button and the Speed increase
button. Press the Stop button and then press the
Incline increase or decrease button. The treadmill will automatically rise to the maximum incline
level and then return to the minimum level. This will
recalibrate the incline system. If the incline does not
begin calibrating, press the Stop button again, and
then press the Incline increase or decrease button
again. When the incline is calibrated, remove the
key from the console.
c.Your treadmill features a walking belt coated with
high-performance lubricant. IMPORTANT: Never
apply silicone spray or other substances to
the walking belt or the walking platform unless
instructed to do so by an authorized service
representative. Such substances may deteriorate the walking belt and cause excessive wear.
If you suspect that the walking belt needs more
lubricant, see the front cover of this manual.
d.If the walking belt still slows when walked on, see
the front cover of this manual.
SYMPTOM: The walking belt slows when walked on
a.
Use only a surge suppressor that meets all of the
specifications described on page 16.
27
SYMPTOM: The walking belt is not centered
between the foot rails. IMPORTANT: If the walking
belt rubs against the foot rails, the walking belt
may be damaged.
SYMPTOM: The walking belt slips when walked on
a. F
irst, remove the key and UNPLUG THE POWER
CORD. Using the hex key, turn both idler roller
screws clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able
to lift each edge of the walking belt 2 to 3 in. (5 to
7 cm) off the walking platform. Be careful to keep
the walking belt centered. Then, plug in the power
cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walking belt
is properly tightened.
a. F
irst, remove the key and UNPLUG THE POWER
CORD. If the walking belt has shifted to the left,
use the hex key to turn the left idler roller screw
clockwise 1/2 of a turn; if the walking belt has
shifted to the right, turn the left idler roller screw
counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Then, plug in the
power cord, insert the key, and run the treadmill
for a few minutes. Repeat until the walking belt is
centered.
a
a
Foot Rails
28
EXERCISE GUIDELINES
Burning Fat—To burn fat effectively, you must exercise at a low intensity level for a sustained period of
time. During the first few minutes of exercise, your
body uses carbohydrate calories for energy. Only after
the first few minutes of exercise does your body begin
to use stored fat calories for energy. If your goal is to
burn fat, adjust the intensity of your exercise until your
heart rate is near the lowest number in your training
zone. For maximum fat burning, exercise with your
heart rate near the middle number in your training
zone.
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for persons
over age 35 or persons with pre-existing
health problems.
The heart rate monitor is not a medical device.
Various factors may affect the accuracy of
heart rate readings. The heart rate monitor is
intended only as an exercise aid in determining heart rate trends in general.
Aerobic Exercise—If your goal is to strengthen your
cardiovascular system, you must perform aerobic
exercise, which is activity that requires large amounts
of oxygen for prolonged periods of time. For aerobic
exercise, adjust the intensity of your exercise until your
heart rate is near the highest number in your training
zone.
These guidelines will help you to plan your exercise
program. For detailed exercise information, obtain a
reputable book or consult your physician. Remember,
proper nutrition and adequate rest are essential for
successful results.
WORKOUT GUIDELINES
EXERCISE INTENSITY
Warming Up—Start with 5 to 10 minutes of stretching and light exercise. A warm-up increases your body
temperature, heart rate, and circulation in preparation
for exercise.
Whether your goal is to burn fat or to strengthen your
cardiovascular system, exercising at the proper intensity is the key to achieving results. You can use your
heart rate as a guide to find the proper intensity level.
The chart below shows recommended heart rates for
fat burning and aerobic exercise.
Training Zone Exercise—Exercise for 20 to 30 minutes with your heart rate in your training zone. (During
the first few weeks of your exercise program, do not
keep your heart rate in your training zone for longer
than 20 minutes.) Breathe regularly and deeply as you
exercise; never hold your breath.
Cooling Down—Finish with 5 to 10 minutes of stretching. Stretching increases the flexibility of your muscles
and helps to prevent post-exercise problems.
EXERCISE FREQUENCY
To find the proper intensity level, find your age at the
bottom of the chart (ages are rounded off to the nearest ten years). The three numbers listed above your
age define your “training zone.” The lowest number is
the heart rate for fat burning, the middle number is the
heart rate for maximum fat burning, and the highest
number is the heart rate for aerobic exercise.
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest
between workouts. After a few months of regular exercise, you may complete up to five workouts each week,
if desired. Remember, the key to success is to make
exercise a regular and enjoyable part of your everyday
life.
29
PART LIST
Model No. PETL13012.0 R1212A
Key No. Qty.
Description
Key No. Qty.
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
#8 x 1/2" Screw
3/8" x 2" Bolt
3/8" x 4" Screw
#10 x 3/4" Screw
#10 Star Washer
#8 x 1/2" Ground Screw
3/8" x 2 1/2" Bolt
5/16" Star Washer
3/8" Nut
3/8" Star Washer
5/16" x 5/8" Screw
5/16" x 2 3/4" Screw
#8 x 3/4" Tek Screw
#8 x 3/4" Pan Head Screw
#8 x 3/4" Screw
1/4" Roller Screw
Key/Clip
#8 x 1 3/4" Screw
#8 x 7/16" Screw
5/16" Motor Screw
#10 Flat Washer
3/8" x 1" Bolt
5/16" x 1 3/4" Shoulder Bolt
1/4" x 1 1/4" Screw
#8 x 1" Screw
#8 x 3/4" Pan Tek Screw
3/8" x 1 1/2" Hex Head Bolt
3/8" x 3" Hex Head Bolt
Base
1/4" Star Washer
5/16" Flat Washer
Incline Frame Washer
5/16" Nut
Hood Clip
Platform Grommet
3/8" Jam Nut
Thick Base Pad
Isolator Top
Isolator
Spring
Isolator Bottom
Left Foot Rail
Warning Decal
Walking Platform
Walking Belt
Right Foot Rail
Belt Guide
1/2" x 2 1/4" Bolt
Reed Switch Clip
Drive Roller/Pulley
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
Magnet
Reed Switch
Cable Tie
Storage Latch
Drive Motor
Motor Belt
Frame
Rear Foot
#8 x 3/4" Machine Bolt
Right Rear Cover
Left Rear Cover
Idler Roller
#8 Nut
Motor Bushing
Motor Hood
Hood Accent
Incline Motor
Incline Frame Insert
Incline Frame
Controller
Electronics Bracket
Hood Post
Power Switch
Power Cord
Power Cord Grommet
Belly Pan
Left Handrail Cover
Left Handrail Insert
Handrail
Ground Wire
Pulse Crossbar
Right Handrail Insert
Right Handrail Cover
Left Upright
Right Upright
Console Clamp
Base Cap
Left Base Cover
Right Base Cover
Grommet
Upright Wire
Thin Base Pad
Wheel
Caution Decal
Left Tray
Right Tray
#8 x 1/2" Console Ground Screw
Console Base
Wire Tie
Console
14
2
6
4
4
12
2
4
4
6
4
4
13
33
11
2
1
2
4
2
6
2
4
1
4
12
1
1
1
1
4
2
4
3
4
4
2
4
4
4
4
1
1
1
1
1
2
2
1
1
30
1
1
4
1
1
1
1
2
1
1
1
1
1
2
1
1
1
2
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
2
4
1
1
1
1
2
2
2
1
1
1
1
1
1
Key No. Qty.
Description
Key No. Qty.
Description
101
102
103
104
105
106
Console Frame
Electronics Bracket
Filter
Motor Isolator
Grounding Bracket
Receptacle
107
108
109
110
*
Chest Strap
Sensor
1/2" Nut
#8 Star Washer
User’s Manual
1
1
1
1
1
1
1
1
2
6
–
Note: Specifications are subject to change without notice. For information about ordering replacement parts, see
the back cover of this manual. *These parts are not illustrated.
31
16
32
14
61
13
35
31
33
23
41
26
40
39
38
62
44
26
58
43 21
15
26
14
60
16
41
40
39
38
45
19
46
47
13
23
14
15
21
42
57
26
58
31
33
35
21
15
15
9
15
21
33
35
31
48
23
49
13
2
41
26
40
39
38
21
15
51
50
52
18
56
6
64
41
26
40
39
19
38
64
55
9
104
48
2
53
110
6
18
102
103
110
24
30
35
31
33
15
110
6
6
47
54
15
21
23
20
59
63
EXPLODED DRAWING A
Model No. PETL13012.0 R1212A
EXPLODED DRAWING B
Model No. PETL13012.0 R1212A
15
15
15
65
66
32
28
68
6
27
69
109
36
67
22
22
36
32
70
105
14
71
6
109
68
6
14
74
110
14
72
14
34
14
72
34
14
106
26
73
34
26
76
26
33
75
EXPLODED DRAWING C
Model No. PETL13012.0 R1212A
12
78
8
77
11
79
4
14
5
97
80
81
4
1
84
1
12
5
83
8
1
1
10
11
82
3
79
36
14
87
85
94
88
6
90
7
36
37
13
87
91
87
92
93
9
10
29
37
13
93
94
9
87
92
13
7
34
3
13
89
10
3
EXPLODED DRAWING D
Model No. PETL13012.0 R1212A
1
98
95
14
1
14
1
99
14
14
1
14
14
100
14
14
14
96
1
14
1
101
86
14
25
14
17
86
107
108
35
25
ORDERING REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to provide the following information when contacting us:
• the model number and serial number of the product (see the front cover of this manual)
• the name of the product (see the front cover of this manual)
• the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED DRAWING
near the end of this manual)
RECYCLING INFORMATION
This electronic product must not be disposed of in municipal waste. To preserve the environment, this product must be recycled after its useful life as
required by law.
Please use recycling facilities that are authorized to collect this type of waste in
your area. In doing so, you will help to conserve natural resources and improve
European standards of environmental protection. If you require more information
about safe and correct disposal methods, please contact your local city office or
the establishment where you purchased this product.
Part No. 339139 R1212A
Printed in China © 2012 ICON IP, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement