LiftMaster 374UT Universal Mini Remote Control

LiftMaster 374UT Universal Mini Remote Control
MODEL 374UT
Universal Mini Remote Control
TABLE OF CONTENTS
GETTING STARTED .................................................... 2
COMMERCIAL DOOR OPERATORS ................................. 10
LOCATE THE PROGRAM/LEARN BUTTON ........................ 3-7
Programming to a commercial door operator
with a RADIO button................................................ 10
GATE OPERATORS .................................................... 11
®
Chamberlain products ............................................. 3
Genie® products ..................................................... 4
Linear® products ..................................................... 5
Wayne Dalton® products ........................................... 5
LiftMaster® products ................................................ 6
Overhead Door® products .......................................... 6
Stanley® products ................................................... 7
GARAGE DOOR OPENERS .......................................... 8-9
Programming to a garage door opener with a
Program/LEARN button ............................................. 8
Programming to a Genie® Intellicode® 2
garage door opener ................................................. 9
Program to a gate operator
with a Program/LEARN button .................................... 11
EXTERNAL RECEIVERS ............................................... 12
Programming to an external receiver
with a Program/LEARN button .................................... 12
ALTERNATE PROGRAMMING OPTIONS ........................... 13
Alternate programming option for products
with a Program/LEARN button .................................... 13
NEED HELP? ........................................................... 14
BATTERY ............................................................... 15
STOP
Read instructions thoroughly BEFORE beginning.
If using the Universal Mini Remote Control with residential door openers, the remote control must be used only
with door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are
always located on or near the bottom of the door track.
To prevent possible SERIOUS INJURY or DEATH from a moving gate or door:
• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote control
transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted and there are no obstructions to door travel.
• ALWAYS keep gate or door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door.
GETTING STARTED
The Universal Mini Remote Control can be programmed to activate up to two products, such as a garage door opener, MyQ® light
control, gate operator, or commercial door operator. Each button on the remote control works independently of the other and must
be programmed separately. The images throughout this manual are for reference only and your product may look different.
Gate Operator
Garage Door Opener
Commercial Door Operator
LED
Bottom Button
You will need to locate the Program/LEARN button on your product before you start programming.
GARAGE DOOR OPENERS
EXTERNAL RECEIVER
The Program/LEARN button is typically located on the back or side panel
of your garage door opener. Your Program/LEARN button may have a
different name (SMART button, SET button, etc.). For help locating your
Program/LEARN button refer to the Table of Contents in this manual or
contact your garage door opener manufacturer.
COMMERCIAL DOOR OPERATORS
The RADIO button is typically located on the logic board of your operator.
For help locating your RADIO button contact your door operator
manufacturer.
GATE OPERATORS
The Program/LEARN button is typically located on the control board of
your operator. Your Program/LEARN button may have a different name
(RADIO button, XMITTER button, etc.). For help locating your Program/
LEARN button contact your gate operator manufacturer.
2
Some products do not
have a Program/LEARN
button. In this case, the
Program/LEARN button
will be located in an
external receiver. The
receiver will be located on
the product or mounted
nearby. Follow the
programming instructions
for an external receiver.
LOCATE THE PROGRAM/LEARN BUTTON
CHAMBERLAIN PRODUCTS
3
LOCATE THE PROGRAM/LEARN BUTTON
GENIE PRODUCTS
Learn Code
Button
Program Set Button
4
LOCATE THE PROGRAM/LEARN BUTTON
LINEAR PRODUCTS
Learn
Button
Learn
Button
WAYNE-DALTON PRODUCTS
Program SW
Button
5
LOCATE THE PROGRAM/LEARN BUTTON
LIFTMASTER PRODUCTS
Yellow Learn
Button
Purple Learn
Button
Orange Learn
Button
Green Learn
Button
OVERHEAD DOOR PRODUCTS
Learn Code
Button
6
LOCATE THE LEARN BUTTON
STANLEY PRODUCTS
Learn Button
7
GARAGE DOOR OPENERS
Programming to a Garage Door Opener with a Program/LEARN Button
The Program/LEARN button is typically located on the back or side panel of the garage door opener or an external receiver. For
help locating your Program/LEARN button contact your garage door opener manufacturer.
If you have a Chamberlain branded garage door opener with a yellow learn button, press and release the learn button, then press
and hold the button on the remote control you would like to use. If programming is not successful, proceed through the steps
below.
If you have a Genie® Intellicode® 2 garage door opener go to the next page.
The images throughout this manual are for reference only and your product may look different.
1
2
Start with your garage door closed.
Press and hold bottom button on the remote control until
the blue LED stays solid (approximately 15 seconds) then
release the button.
LED
Bottom Button
IMPORTANT: The remote will activate your garage door during
programming. Ensure garage door is clear of ALL obstructions.
3
4
Press and release the Program/LEARN button on your
garage door opener.
On the remote control, press and release the button that
you would like to program twice. The blue LED will blink
for up to 60 seconds.
LED
5
6
Wait for the garage door to move, then press and release
either of the buttons on the remote.
8
Test the remote control by pressing the button you
programmed in step 4. If the garage door opener does not
activate, repeat the programming steps.
GARAGE DOOR OPENERS (continued)
Programming to a Genie® Intellicode® 2 Garage Door Opener
Before starting, you MUST have an existing Genie® Intellicode® 2 remote control programmed to the garage door opener. For help
programming a Genie Intellicode 2 remote control, see your owner’s manual.
The images throughout this manual are for reference only and your product may look different.
1
2
Start with your garage door closed.
Press and hold bottom button on the remote control until
the blue LED stays solid (approximately 15 seconds) then
release the button.
LED
Bottom Button
IMPORTANT: The remote will activate your garage door during
programming. Ensure door is clear of ALL obstructions.
3
Wait for the round LED on the garage door opener to
flash BLUE then press and release either of the buttons
on the remote.
5
Press and release the Program/Set button and the long
LED will flash PURPLE.
7
4
6
8
On the remote control, press and release the button that
you would like to program 3 times. The blue LED will blink
for up to 60 seconds.
On the garage door opener, press and hold the
Program/Set button until both the long and short LED’s
light up BLUE.
On the Genie® remote control, press and release the
button that is already programmed to the garage door
opener. Both LED’s will flash PURPLE.
The garage door will open.
LED
Test the remote control by pressing the button you
programmed in step 7. If the garage door opener does not
activate, repeat the programming steps.
9
COMMERCIAL DOOR OPERATORS
Programming to a Commercial Door Operator with a RADIO Button
The RADIO button is typically located on the logic board of the operator or an external receiver. For help locating your RADIO
button contact your commercial door operator manufacturer.
The images throughout this manual are for reference only and your product may look different.
1
2
Start with your commercial door closed.
Press and hold bottom button on the remote control until
the blue LED stays solid (approximately 15 seconds) then
release the button.
LED
Bottom Button
IMPORTANT: The remote will
activate your commercial door
during programming. Ensure
door is clear of ALL
obstructions.
3
4
Press and release the RADIO button on your commercial
door operator. The RADIO LED will illuminate.
RADIO LED
On the remote control, press and release the button that
you would like to program twice. The blue LED will blink
for up to 60 seconds.
LED
RADIO Button
5
6
Wait to see if the LED on the operator flashes rapidly,
indicating the remote control is programmed to the
operator. Press and release the RADIO button on your
commercial door operator to exit programming mode.
RADIO Button
7
Test the remote control by pressing the button you
programmed in step 4. If the commercial door operator
does not activate, repeat the programming steps or visit
LiftMaster.com/374ut for additional instructions.
10
Wait for commercial door to move, then press and release
either button on the remote control to exit programming
mode.
GATE OPERATORS
Programming to a Gate Operator with a Program/LEARN Button
The Program/LEARN button is typically located on the control board of the operator or an external receiver. For help locating your
Program/LEARN button contact your gate operator manufacturer.
The images throughout this manual are for reference only and your product may look different.
1
2
Start with your gate closed.
Press and hold bottom button on the remote control until
the blue LED stays solid (approximately 15 seconds) then
release the button.
LED
Bottom Button
IMPORTANT: The remote will activate your gate during
programming. Ensure gate is clear of ALL obstructions.
3
4
Press and release the Program/LEARN button* on your
gate operator. The Program/LEARN LED will illuminate.
Program/LEARN
Button*
On the remote control, press and release the button that
you would like to program twice. The blue LED will blink
for up to 60 seconds.
LED
Program/LEARN
LED
* Depending on your product, the Program/LEARN button may have a different
name (use the button for programming remote controls).
5
6
Wait for the gate to move or the program/LEARN LED on
the gate operator blinks, then press and release either of
the buttons on the remote.
11
Test the remote control by pressing the button you
programmed in step 4. If the gate operator does not
activate, repeat the programming steps or visit
LiftMaster.com/374ut for additional instructions.
EXTERNAL RECEIVERS (continued)
Programming to an External Receiver with a Program/LEARN Button
STOP
If using the Universal Mini Remote Control with residential door openers, the remote control must be used only with
door openers manufactured after 1993 that utilize photoelectric sensors. The photoelectric sensors are always located
on or near the bottom of the door track.
The external receiver is typically located on the product or mounted near the product.
The images throughout this manual are for reference only and your product may look different.
1
2
Start with your garage door, commercial door, or gate
closed.
Press and hold bottom button on the remote control until
the blue LED stays solid (approximately 15 seconds) then
release the button.
LED
Bottom Button
IMPORTANT: The remote will activate your door or gate during
programming. Ensure door or gate is clear of ALL obstructions.
3
4
Press and release the Program/LEARN button* on the
external receiver.
Program/LEARN
Button*
On the remote control, press and release the button that
you would like to program twice. The blue LED will blink
for up to 60 seconds.
LED
* Depending on your product, the Program/SMART/LEARN button may have a
different name (use the button for programming remote controls).
5
6
Wait for the door or gate to move, then press and release
either of the buttons on the remote.
12
Test the remote control by pressing the button you
programmed in step 4. If the garage door opener,
commercial door operator, or gate operator does not
activate, repeat the programming steps.
MYQ® LIGHT CONTROLS
Programming to a MyQ® Light Control
The images throughout this manual are for reference only and your product may look different.
1
3
5
2
Plug the lamp into the module and plug the module
into an electrical outlet (the LED on the module will
flash). NOTE: Make sure the lamp is switched ON.
4
Press and release the LEARN button on the module (the
LED on the module will light).
If the lamp is not ON, press and release the Power button
on the module to turn the lamp ON.
Press the button on the remote control.
LED
The lamp’s light bulb will blink and the LED on the
module will turn OFF when the device has been
programmed.
13
Button
NEED HELP?
The remote control does not have good range.
•
The range of the remote control may vary depending on various factors and environmental factors
The remote control will not program to a product with a Program/LEARN button.
•
Check the battery in the remote control. The LED should light when you press a button. Replace the battery if necessary.
The remote control LED will not light or it is dim.
•
Replace the battery.
The remote control LED does not activate the product until it is close to the product.
•
Replace the battery.
14
BATTERY
Screw
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V CR2032 coin batteries.
• DO NOT recharge, disassemble, heat above 212°F (100°C)
or incinerate.
Battery
NOTICE: To comply with FCC and or Industry Canada (IC) rules, adjustment or
modifications of this receiver and/or transmitter are prohibited, except for
changing the code setting or replacing the battery. THERE ARE NO OTHER USER
SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is
subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Dispose of batteries properly. Replace ONLY with 3V CR2032 coin
batteries.
Need Help?
Go to LiftMaster.com/374ut or call
1-800-442-1255
LiftMaster.com
1-800-442-1255
Chamberlain and LiftMaster are Trademarks of Chamberlain Group. Genie is a Trademark of Overhead Door Corporation.
Overhead Door is a Trademark of Overhead Door Corporation. Linear is a Trademark of Linear Corporation. Master Mechanic
is a Trademark of TruServ. Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark of The Stanley Works. Wayne
Dalton is a trademark of Wayne Dalton Corporation. Do It is a trademark of Do It Best Corporation.
GDOPro103
© 2016, LiftMaster
All Rights Reserved
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising