installation and wire connection manual

1. SAFETY PRECAUTIONS
❏❏Symbol Identification
This manual uses symbols and icons to
indicate safety precautions and concerns
during the installation procedure. Be sure
to carefully read and understand each
precaution prior to beginning the installation.
❏❏Before Use
CAUTION
WARNING
•Confirm the battery voltage of the
vehicle to be installed. This unit is
designed only for vehicles with DC
12V power supply.
•Disconnect the negative terminal of
the battery before connecting wires,
otherwise an electric shock, injury
by short circuit may occur.
WARNING
•This symbol is intended to alert the
user to the presence of important
operating instructions. Failure to
heed the instructions may result in
severe injury or death.
CAUTION
•This symbol is intended to alert the
user to the presence of important
operating instructions. Failure to
heed the instructions can result in
injury or material damage.
Car battery
❏❏Installation Precautions
WARNING
•When installing the unit to a vehicle
with an airbag system, never install
it in a place where it may affect the
operation of the airbag.
•Do not install this unit in the
following locations:
A location interfering with the
driver’s visual range or operation.
A location where the gear shift or
brake pedal are hindered.
A location where passengers are at
risk.
An unstable location, or where the
system may fall.
•Do not install the system in the
locations described below. This may
cause a fire, accident or electrical
shock:
A location exposed to rain or dust.
An unstable location, or where the
system may fall.
•Do not install this unit in a place
exposed to direct sunlight, heat or a
place where the vent holes or heat
radiation holes are covered.
•When you install the antenna, mount
it in a place where the elements of
the antenna do not protrude beyond
the edge of the front, back, left and
right of the vehicle.
If it comes in contact with
pedestrians, it may cause an
accident.
❏❏Installation Notes
WARNING
•Please note the position of pipes,
tanks and electrical wirings before
installing the unit into the vehicle;
failure in avoiding these may cause
a fire or malfunction.
CAUTION
•Use only the supplied parts.
If unspecified parts are used, they
may cause damage.
English
INSTALLATION AND WIRE
CONNECTION MANUAL
•Any holes made in the body of the
vehicle should be sealed with a
silicon adhesive.
If exhaust fumes or water penetrates
into the vehicle, this may cause an
accident.
•Fasten the bolts securely when
installing the unit. If the bolts are
loose an accident or malfunction
could occur.
❏❏Connection Notes
WARNING
•Loom all cables according to the
instruction manual, so as not to
hinder operation.
•Wire the connecting cords/cables
away from high temperature areas.
If the coatings of the cables melt,
it could cause an accident/fire by a
short circuit.
Take care when wiring in the engine
compartment.
•When wiring the connecting cables
in a vehicle with an airbag system,
never feed the cables through
a place where it may affect the
operation of the airbag.
An airbag not operating correctly in
an emergency may cause increased
injury.
NX604/FX503
57
CAUTION
English
•Verify wires with a digital multi-meter
prior to making any connections.
Many new vehicles use multiplexed
and/or low voltage circuits that can
be damaged if a test light or logic
probe is used.
•Connect cables appropriately. If a
wrong connection is made, this may
cause a fire or accident.
•When passing cables through
the body of the vehicle, use nonconductive grommets.
If the coatings of the cables are
worn out by rubbing, this may cause
an accident, fire or a short circuit.
•After wiring cables, fix them with
insulation tape.
•Be sure to switch off the vehicle
when connecting or disconnecting
cables to/from the unit, otherwise
an electric shock, injury or accident
may occur.
2. PACKAGE CONTENTS
Main unit
Quick Start Guide & Installation
Manual
CD-ROM
•Owner’s manual
•Owner’s manual - Navigation (NX604
only)
Power supply cable
RCA pin cable (6ch)
RCA pin cable (Rear AUX-IN/Rear
Video Out)
Bag for accessories
•Flat head screw (M5 × 8 mm)
������������������������������������������������������������8
•Hexagonal bolt (M5 × 8 mm)
������������������������������������������������������������8
•Rubber cap (for RCA pin cable)
����������������������������������������������������������10
•Cable holder (NX604 only)
���������������� 3
•Double-sided tape for fastening GPS
antenna (NX604 only)
���������������� 1
•Cable tie������������ 1
Finisher
3. GENERAL CAUTIONS
5. INSTALLING THE MAIN UNIT
●● Do not open the case. There are no userserviceable parts inside. If you drop
anything into the unit during installation,
consult your dealer or an authorized
Clarion service center.
This unit is designed for fixed installation in
the dashboard.
●● When installing the main unit in NISSAN
vehicles, use the parts attached to the
unit and follow the instructions in Figure
3.
When installing the main unit in TOYOTA
vehicles, use the parts attached to the
vehicle and follow the instructions in
Figure 4.
●● Wire as shown in Section 9→ P.61.
●● Reassemble and secure the unit in the
dashboard and set the face panel and
center panel.
4. CAUTIONS ON INSTALLATION
●● Prepare all articles necessary for
installing the main unit before starting.
●● Install the unit within 35° of the horizontal
plane. (Figure 1)
Mounting Screw Holes (Side View of
the Main Unit)
Max. 35°
Figure 1
●● If you have to do any modification on the
car body, such as drilling holes, consult
your car dealer beforehand.
●● Use the included screws for installation.
Using other screws can cause damage.
(Figure 2)
Chassis
For NISSAN vehicle
Chassis
Warranty card
Damage
GPS antenna (NX604 only)
USB Cable
Microphone (NX604 only)
Notice
•The provided disc (CD-ROM manual)
cannot be played back on this unit.
58
NX604/FX503
Max. 3 mm (M4 screw)/
Max. 8 mm (M5 screw)
Figure 2
For TOYOTA vehicle
❏❏Installing the Main Unit in a NISSAN Vehicle
❏❏Installing the Main Unit in a TOYOTA Vehicle
Install by using parts attached to the vehicle. (Screws marked
are attached to the vehicle.)
English
Main Unit
6-Spacer (thickness: 1 mm)
Main Unit
8-Hexagonal screw
(M5 x 8)
Finisher ✽1
Mounting bracket
(1 pair for the left and right sides)
Figure 3
6-Flat head screw
(M5 x 8)
(attached to the main unit)
Mounting bracket
(1 pair for the left
and right sides)
3
✽
Center Panel ✽2
1Position the face panel with its wide edge at the bottom. Fit the edge into the groove of the main
unit.
✽
Figure 4
2Some panel openings are too small for the unit depending on the vehicle type and model. In
such a case, trim the upper and lower sides of the panel frame by about 0.5 to 1.5 mm so the
unit can be inserted smoothly.
✽
3If a hook on the installation bracket interferes with the unit, bend and flatten it with a nipper or
similar tool.
✽
Typical Mounting Brackets
Example 1
Example 2
Affix the screws to the
Example 3
marks.
NX604/FX503
59
❏❏Vehicles other than NISSAN
and TOYOTA
English
In some cases the center panel may require
modification. (Trimming, filing, etc.)
6. REMOVING THE MAIN UNIT
CAUTION
•After connecting the HDMI and USB
cables to the unit, use a cable tie to
tie them down. (Figure 6)
Cable tie
7. CAUTIONS ON WIRING
Fuse (15A
FUSE)
Fuse holder
Figure 5
●● There are various types of fuse holder.
Do not let the battery side touch other
metal parts.
60
NX604/FX503
WARNING
•Do not install the GPS antenna in a place where it may interfere with the operation
of the airbag or hinder the driver’s visual range.
•Do not use the navigation system with the GPS antenna cable cut off. The power
line in the cable may be short-circuited.
When the main unit is to be removed,
disassemble it in the reverse of the order in
“INSTALLING THE MAIN UNIT”.→ P.58
●● Be sure to turn the power off before
wiring.
Be particularly careful where you route
the wires.
●● Keep them well away from the engine,
and exhaust pipe, etc. Heat may damage
the wires.
●● If the fuse should blow, check to see if
the wiring is correct.
If a fuse is blown, replace it with a new
one of the same specification as the
original.
●● To replace the fuse, remove the old fuse
of the power supply cable and insert the
new one. (Figure 5)
8. INSTALLING THE GPS ANTENNA (NX604 ONLY)
HDMI
Cable
USB Cable
Figure 6
●● The supplied GPS antenna is for installation inside the vehicle. Do not install it outside the
vehicle.
●● Install the GPS antenna more than 19.7in (50 cm) away from the main unit, other audio
devices such as CD player, and a radar detector. If it is installed near these devices, GPS
reception may be impaired.
●● To improve the GPS signal reception, install the GPS antenna horizontally on a flat plane.
●● Do not wax or paint the cover of the GPS antenna. This may reduce the performance of
the GPS antenna.
●● Install the GPS antenna at least 3.9in (10 cm) away from the windshield.
●● Wipe off the dirt of the mounting surface before installing the GPS antenna.
●● Stick the double-sided tape to the bottom face of the GPS antenna.
Double-sided
tape
Bottom face of the GPS antenna
9. WIRE CONNECTION
Refer to the following
page.
Radio antenna jack
English
●● Mount the GPS antenna.
Stick it surely on a flat plane of the passenger-side dashboard where GPS signal
interruption is minimized.
●● Wire the GPS antenna cable.
Fasten the cable using the Cable holders.
USB terminal
GPS antenna
jack (NX604
only)
HDMI/MHL
conversion adapter
Rear Vision
Camera
terminal
Android
smartphone
HDMI conversion cable
HDMI cable
(sold separately)
or
GPS antenna
SiriusXMConnect
Vehicle Tuner
terminal (sold
separately)
Android
smartphone
Cable holder
Microphone
Steering
wheel remote
control
terminal (sold
separately)
Gray
Black
Purple
Gray
Black
Red
White
Red
Right
Left
Right
Left
White
Red
White
Yellow
Right
Left
Red
Black
White
Rear
audio
output
terminal
Subwoofer
output
terminal
(MONO 2ch)
video output
terminal
Yellow
video input
terminal
Right
Left
External
Amplifier
Front
audio
output
terminal
Rear Monitor
iPod/iPhone
Connection cable
(CCA-750)
audio input
terminal
NX604/FX503
61
Yellow
+12V main power
Black
English
Purple
Purple/Black
Ground
Rear right
Rear right
Red
Gray
Gray/Black
White
White/Black
Green
Green/Black
Blue/White
Orange/White
Blue
Grass-Green
Purple/White
+12V accessory
Front right
Connecting the parking brake lead
Connect the lead to parking brake lamp ground in the meter panel.
●● Connecting the parking brake lead to lamp ground allows you to watch video images
when the parking brake is engaged.
●● When the parking brake lead is not connected, the monitor will not display video images.
●● If “Audio Only” appears on the screen just after turning on the ACC power of the car,
release the parking brake while confirming safety, and then engage the parking brake
again.
Parking brake lamp
+ lead to battery
Front right
Parking brake
● How to attach the electro-tap
1.Place the Parking brake lead at the stopper,
and fold it back in the direction of the arrow.
2.Pass the Parking brake signal lead through,
and fold it back in the direction of the arrow.
Front left
Front left
Electro-tap
(sold
separately)
Rear left
Parking brake
signal lead
Parking brake
signal lead
Parking brake
signal lead
Rear left
Amplifier turn-on lead
Parking brake lead
(Grass-Green)
Stopper
Illumination
Auto antenna
Parking brake lead
Reverse gear lead
Parking brake lead
(Grass-Green)
❏❏Connecting the Accessories
Connection to the Rear Vision Camera for vehicle
The Rear Vision Camera for vehicle can be connected to optional Rear Vision Camera input
cable (CCA-644) with RCA pin cable. For detailed information, refer to the instruction sheet
or manual for the Rear Vision Camera.
●● Be sure to connect the reverse gear lead to the vehicle’s relevant terminal.
●● Connect the Rear Vision Camera to the RCA pin cable; if not, the screen turns black
while the gearshift lever is in the reverse gear position.
SiriusXM-Connect Vehicle Tuner
See next page for how to connect the parking brake lead.
62
NX604/FX503
Connect this tuner to SiriusXM-Connect Vehicle Tuner terminal.
For more information on how to install the SiriusXM Connect Vehicle tuner, consult the
installation guide included with the tuner.