User Manual
INSTRUCTION MANUAL
CORDED DRILL
054-1213-0
Read and understand this instruction manual
thoroughly before using the product. It contains
important information for your safety as well as
operating and maintenance advice.
TECHNICAL SPECIFICATIONS 3
SAFETY GUIDELINES 4–7
DESCRIPTION8
OPERATING INSTRUCTIONS 9–13
MAINTENANCE 14–15
TROUBLESHOOTING 16
PARTS LIST 17–18
WARRANTY 19–20
Keep this instruction manual for future use. Should
this product be passed on to a third party, then this
instruction manual must be included.
CORDED DRILL - 054-1213-0
CORDED DRILL - 054-1213-0
TABLE OF CONTENTS
If any parts are
missing or damaged,
or if you have any
questions, please call
our toll-free helpline
at 1-800-689-9928.
2
4
WARNING!
RATED POWER
5A
RATING VOLTAGE
120V, 60 Hz ~
NO LOAD SPEED
0–2700 RPM
Safety symbols in this Instruction Manual are used to flag possible dangers. The safety
symbols and their explanations require your full understanding. The safety warnings do
not, by themselves, eliminate any danger, nor are they substitutes for proper accident
prevention measures.
KEYLESS CHUCK
3/8" (10 mm)
WARNING!
MAXIMUM DRILLING CAPACITY
IN WOOD
IN METAL
1" (25.4 mm)
3/8" (10 mm)
TOOL WEIGHT
3 lb 10 oz (1.64 kg)
This Safety Alert Symbol indicates caution, warning, or danger. Failure to obey a safety
warning can result in serious injury to yourself or others. To reduce the risk of injury, fire, or
electric shock, always follow the safety precautions.
Know your tool
To operate this tool, carefully read this Instruction Manual and all labels affixed to the corded drill
before using. Keep this manual available for future reference.
Important
This tool should only be serviced by a qualified service technician. For more information, call the
toll-free helpline at 1-800-689-9928.
Read all instructions thoroughly
Save these instructions
General power tool safety warnings
WARNING!
Read all safety warnings and instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
CORDED DRILL - 054-1213-0
CORDED DRILL - 054-1213-0
SAFeTY GUIDELINES
TECHNICAL SPECIFICATIONS
3
Work area safety
SAFETY GUIDELINES
• Keep the work area clean and well lit. Cluttered or dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools create sparks, which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool. Distractions can cause
you to lose control.
Electrical safety
• Power tool plugs must match the outlet. Never modify the plug in any way. Do not use
any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching
outlets will reduce the risk of electric shock.
• Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges
and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions. Water entering a power tool will increase
the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power
tool. Keep the cord away from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
• If operating a power tool in a damp location is unavoidable, use a ground-fault circuit
interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.
Personal safety
• Stay alert, watch what you are doing and use common sense when operating a power tool.
Do not use the tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury.
• Use personal protective equipment. Always wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or hearing protection, used for appropriate conditions,
will reduce personal injuries.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting
to power source and/or battery pack, picking up or carrying the tool. Carrying power tools
with your finger on the switch or energising power tools that have the switch on invites accidents.
CORDED DRILL - 054-1213-0
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. This enables better control of
the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection facilities, ensure
that these are connected and properly used. Use of these devices can reduce dust-related hazards.
Power tool use and care
• Do not force the power tool. Use the correct power tool for your application. The correct
power tool will do the job better and more safely at the rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/or the battery pack from the power tool
before making any adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar
with the power tool or these instructions to operate the power tool. Power tools are
dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or binding of moving parts, breakage of
parts and any other condition that may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many accidents are caused by poorly maintained
power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
• Use the power tool, accessories, tool bits, etc. in accordance with these instructions,
taking into account the working conditions and the work to be performed. Use of the power
tool for operations different from those intended could result in a hazardous situation.
Service
• Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is maintained.
CORDED DRILL - 054-1213-0
6
SAFETY GUIDELINES
5
Safety guidelines for corded drill
8
Know your tool
SAFETY GUIDELINES
• Use the auxiliary handles if supplied with the tool. Loss of control can cause personal injury.
• Hold the power tool by the insulated gripping surfaces when performing an operation
where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire
may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
• The label on your tool may include the following symbols. The symbols and their
definitions are as follows:
4
3
1
2
7
V ..................... Volts
A ..................... Amperes
5
6
Hz ................... Hertz
W .................... Watts
min ................. Minutes
............... Alternating current
............. Direct current
n0 ................... No-load speed
............... Class II Construction
…/min ........... Revolutions per minute
............... Grounding terminal
BPM ............... Beats per minute
.............. WARNING – To reduce the risk of injury, user must read instruction manual.
• Use clamps or another practical way to support the workpiece and secure it to a stable
platform. Holding the workpiece by hand or against your body is unstable and may lead to loss of control.
• Inspect the tool cords periodically and, if damaged, have them repaired by a qualified
repair person. Constantly stay aware of the cord location. Following this rule will reduce the risk of
electric shock or fire.
No.
Description
1
Chuck Jaws
2Chuck Sleeve
3Collar
4
Belt Clip
No.
Description
5
Lock-on Button
6Variable-speed Trigger
7Direction-of-rotation Selector
Before attempting to use this tool, become familiar with all of its operating features and safety
requirements. For optimum performance and safety, read the following operating instructions carefully
before using.
WARNING!
Do not allow familiarity with the drill to cause a lack of alertness. A fraction of a second of
carelessness is enough to cause severe injury.
Contents:
Corded drill and instruction manual.
WARNING!
Remove the drill from the package and examine it carefully. Do not discard the carton or
any packaging material until all parts have been examined.
CORDED DRILL - 054-1213-0
CORDED DRILL - 054-1213-0
DESCRIPTION
7
WARNING!
Never connect the drill to the power source when you are assembling parts, making
adjustments, installing or removing bits, cleaning, or when it is not in use. Disconnecting
the drill will prevent accidental starting, which could cause serious personal injury.
Variable-speed trigger switch
(fig 1)
1. Connect the power cord of your drill to a
standard household power outlet.
2. To turn the drill ON, press the trigger switch.
fig 1
Variable-speed
trigger switch
Lock-on button
3. To turn the drill OFF, release the trigger switch.
4. The variable-speed trigger switch delivers
higher speed with increased trigger pressure
and lower speed with decreased trigger
pressure.
Direction-of-rotation selector
(fig 2)
The direction of bit rotation is reversible and is
controlled by a selector located above the trigger
switch. With the drill held toward you:
1. Position the direction-of-rotation selector to
the right of the tool for forward rotation.
This drill is equipped with a lock-on button, which is convenient for continuous drilling for extended
periods of time.
1. To drill continuously, press and hold the trigger switch and then press the lock-on button. Release
the trigger switch.
2. To unlock the lock-on button and stop continuous drilling, press the trigger switch and the lock-on
button will release automatically.
fig 2
Reverse
Forward
Direction-ofrotation selector
2. Position the direction-of-rotation selector to
the left of the tool for reverse rotation.
WARNING!
To prevent gear damage, always allow the drill to come to a complete stop before changing
the direction of rotation.
Installing bits (fig 3)
1. Unplug the drill from the power source.
Lock-on button (fig 1)
10
2. Hold the collar and turn the sleeve
counterclockwise to open the chuck jaws.
fig 3
Sleeve
Clockwise
(tighten)
3. Open the chuck jaws until the opening is
slightly larger than the bit you intend to use,
and raise the front of the drill slightly to keep
the bit from falling out of the chuck jaws.
Collar
4. Insert the drill bit into the chuck.
5. Hold the collar firmly and turn the sleeve clockwise to tighten the chuck.
WARNING!
Insert the drill bit straight into the chuck jaws. Inserting the drill bit into the chuck jaws
at an angle and then tighten the chuck and using the drill could cause the drill bit to be
thrown from the drill, resulting in possible serious personal injury or damage to the chuck
WARNING!
Never hold the collar by one hand and press the trigger to release/tighten the chuck which
could cause serious personal injury.
CORDED DRILL - 054-1213-0
CORDED DRILL - 054-1213-0
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
9
Removing Bits (fig 4)
WARNING!
Use protective gloves when removing
the bit from the tool, or allow the bit
to cool down first. The bit may be hot
after prolonged use.
fig 4
Sleeve
Drilling in wood
For maximum performance, use high-speed steel or brad-point bits for wood drilling.
Counterclockwise
(loosen)
1. Unplug the drill from the power source.
12
1. Begin drilling at a very low speed to prevent the bit from slipping off the starting point.
2. Increase the speed as the drill bit enters the material.
Collar
2. Hold the collar and turn the sleeve
counterclockwise to open the chuck jaws.
3. Remove the drill bit.
WARNING!
Never hold the collar by one hand and press the trigger to release/tighten the chuck which
could cause serious personal injury.
3. When drilling holes all the way through the workpiece, place a block of wood behind the workpiece
to prevent ragged or splintered edges on the back side of the hole.
Drilling in metal
For maximum performance, use high-speed steel bits for metal or steel drilling.
1. When drilling metals, use light oil on the drill bit to keep it from overheating. The oil will prolong the
life of the bit and increase the drilling action.
2. Begin drilling at a very low speed to prevent the bit from slipping off the starting point.
3. Maintain a speed and pressure that allows cutting without overheating the bit. Applying too much
pressure will:
• Overheat the drill
Drilling
1. Secure the material to be drilled in a vise or with clamps to keep it from turning as the drill bit rotates.
2. Install the correct bit.
3. Verify that the direction-of-rotation selector is at the correct setting (forward).
• Wear the bearings
• Bend or burn the bits
• Produce off-center or irregularly-shaped holes
4. Hold the drill firmly and place the bit at the point to be drilled.
5. Press the trigger switch to start the drill.
6. Move the drill bit into the workpiece, applying only enough pressure to keep the bit cutting. Do not
force the drill or apply side pressure to elongate a hole. Allow the tool to do the work.
7. When drilling hard, smooth surfaces, use a center punch to mark the desired location of the hole.
This will prevent the drill bit from slipping off-center as the hole is started.
8. When drilling metals, use light oil on the drill bit to keep it from overheating. The oil will prolong the
life of the bit and increase the drilling action.
9. If the bit jams in the workpiece or if the drill stalls, stop the tool immediately. Reverse the direction
of rotation and gently squeeze the trigger switch to remove the bit from the workpiece. Investigate
and correct the cause of jamming before you resume work.
CORDED DRILL - 054-1213-0
CORDED DRILL - 054-1213-0
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
11
14
Screw driving
Before each use
Try to use modern screws for easy driving and improved grip.
1. Inspect the drill, the trigger switch, the cord and the accessories for damage.
1. Install the correct driver bit.
2. Check for damaged, missing, or worn parts.
2. Insert the driver bit into the screw head, applying only enough pressure to engage the bit in the
screw head.
3. Check for loose screws, misalignment or binding of moving parts, or any other condition that may
affect the operation.
3. Apply minimal pressure to the trigger initially. Increase the speed only when full control can be
maintained.
4. If abnormal vibration or noise occurs, turn the tool off immediately and have the problem
corrected before further use. Unplug the tool from power source before cleaning or performing
any maintenance. Using compressed air may be the most effective cleaning method. Always wear
safety goggles when cleaning tools using compressed air.
4. Keep sufficient pressure on the drill to prevent the bit turning out of the screw head. The screw
head can easily become damaged, making it difficult to drive it home or remove it.
5. To stop the drill, release the trigger switch and allow the tool to come to a complete stop.
WARNING!
It is advisable to drill a pilot hole first, slightly longer than the screw to be driven and just smaller than
the shank diameter of the screw. The pilot hole will act as a guide for the screw and will also make
tightening the screw less difficult. When screws are positioned close to an edge of the material, a pilot
hole will also help to prevent splitting of the wood.
Do not allow brake fluids, gasoline and petroleum-based products, penetrating oil, etc.
come into contact with plastic parts. These substances contain chemicals that can
damage, weaken, or destroy plastic.
Use a countersinking bit (available separately) to accommodate the screw head, so that it does not
protrude from the surface.
If the screw becomes difficult to drive home, remove the screw and try a slightly larger or longer pilot
hole, but remember that there must be enough remaining material for the screw to grip! If restarting a
screw in a hole, make the first few turns by hand. If the screw is still difficult to drive (as when using
very hard woods) try using a lubricant such as soap; liquid soap is usually best.
WARNING!
When servicing, use only identical replacement parts. The use of any other parts may
create a hazard or cause damage to the product.
WARNING!
Use only accessories that are recommended for this drill by the manufacturer. Accessories
that may be suitable for one tool may become hazardous when used with another tool.
WARNING!
If the supply cord of this power tool is damaged, it must be replaced by a specially
prepared cord available through the service organization
WARNING!
Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with
sharp cutting edges are less likely to bind, and are easier to control.
WARNING!
To ensure safety and reliability, all repairs should be performed by a qualified service
technician.
CORDED DRILL - 054-1213-0
CORDED DRILL - 054-1213-0
MAINTENANCE
OPERATING INSTRUCTIONS
13
Removing the chuck (fig 5)
MAINTENANCE
1. Unplug the drill from the power source.
16
fig 5
2. Open the chuck jaws by turning the sleeve in
a counterclockwise direction.
3. Use a Phillips screwdriver (not included) to
remove the chuck screw by turning it in a
clockwise direction.
Mallet
PROBLEM
4. Insert a 5/16 in. or larger hex key (not
included) into the chuck and securely tighten
the chuck jaws around the hex key.
SOLUTIONS
The motor does not start
The tool is not connected to a power
source
Connect the tool to a power source
The bit cannot be installed
1. The sleeve is not released
2. The bit does not fit the chuck jaw
1. Release the sleeve
2. Use the appropriate bit
The motor is overheating
Ensure cooling vents are free of dust
and obstacles
Clean and clear vents. Do not cover
with hand during operation
Chuck jaws
Hex wrench
POSSIBLE CAUSES
If the problem remains unsolved after performing the checks described above, call the tollfree helpline at 1-800-689-9928.
5. Tap the hex key sharply with a mallet (not included) in a counterclockwise direction. This will loosen
the chuck for easy removal.
NOTICE: The chuck screw has left-handed threads. Attach a new chuck to the spindle and tighten the
chuck screw.
CORDED DRILL - 054-1213-0
CORDED DRILL - 054-1213-0
TROUBLESHOOTING
15
No. Part No.
Description
1 541213001
Screw
2
541213002Chuck
3 541213003
Output Shaft
4 541213004
Steel Ball
5 541213005
Ball Bearing
6
541213006Circlip
7
541213007Gear
8
541213008Circlip
9 541213009
Ball Bearing
10541213010 Bracket
11 541213011
Ball Bearing
12 541213012
Rotor
13 541213013
Brush Holder Box
14 541213014
Copper Brush Holder
15 541213015
Carbon Brush
No. Part No.
Description
16 541213016
Brush Holder Box Cover
17
541213017Stator
18 541213018
Ball Bearing
19 541213019
Bearing sleeve
20 541213020
Forward/Reverse Lever
21
541213021Switch
22
541213022Wire (white)
23
541213023Wire (black)
24 541213024
Cable Pressing Board
25541213025 Screw
26 541213026
Cable Jacket
27 541213027
Cable & Plug
28 541213028
Screw
29 541213029
Right Housing
30 541213030
Left Housing
If the problem remains unsolved after performing the checks described above, call the tollfree helpline at 1-800-689-9928.
CORDED DRILL - 054-1213-0
CORDED DRILL - 054-1213-0
18
PARTS LIST
Exploded view
PARTS LIST
17
f) this warranty will not apply to any product that was sold to the original purchaser as a
reconditioned or refurbished product (unless otherwise specified in writing);
20
g) this warranty will not apply to any product or part thereof if any part from another manufacturer
is installed therein or any repairs or alterations have been made or attempted by unauthorized
persons;
h) this warranty will not apply to normal deterioration of the exterior finish, such as, but not limited
to, scratches, dents, paint chips, or to any corrosion or discolouring by heat, abrasive and chemical
cleaners; and
i) this warranty will not apply to component parts sold by and identified as the product of another
company, which shall be covered under the product manufacturer’s warranty, if any.
This Mastercraft product is guaranteed three (3) years from the date of original retail purchase
against defects in materials and workmanship, except for the following components:
Additional limitations
a)Component A: Batteries, chargers and carrying case, which are guaranteed for a period of 2 years
from the date of original retail purchase against defects in workmanship and materials;
This warranty applies only to the original purchaser and may not be transferred. Neither the retailer
nor the manufacturer shall be liable for any other expense, loss or damage, including, without
limitation, any indirect, incidental, consequential or exemplary damages arising in connection with the
sale, use or inability to use this product.
b)Component B: Accessories, which are guaranteed for a period of 1-year from the date of original
retail purchase against defects in workmanship and materials.
Subject to the conditions and limitations described below, this product, if returned to us with proof
of purchase within the stated warranty period and if covered under this warranty, will be repaired or
replaced (with the same model, or one of equal value or specification), at our option. We will bear the
cost of any repair or replacement and any costs of labour relating thereto.
Notice to consumer
These warranties are subject to the following conditions and
limitations:
IMPORTED BY MASTERCRAFT CANADA TORONTO, CANADA M4S 2B8
This warranty gives you specific legal rights, and you may have other rights, which may vary from province to
province. The provisions contained in this warranty are not intended to limit, modify, take away from, disclaim
or exclude any statutory warranties set forth in any applicable provincial or federal legislation.
a) a bill of sale verifying the purchase and purchase date must be provided;
b) this warranty will not apply to any product or part thereof which is worn or broken or which has
become inoperative due to abuse, misuse, accidental damage, neglect or lack of proper installation,
operation or maintenance (as outlined in the applicable owner’s manual or operating instructions)
or which is being used for industrial, professional, commercial or rental purposes;
c) this warranty will not apply to normal wear and tear or to expendable parts or accessories that
may be supplied with the product which are expected to become inoperative or unusable after a
reasonable period of use;
d) this warranty will not apply to routine maintenance and consumable items such as, but not limited
to, fuel, lubricants, vacuum bags, blades, belts, sandpaper, bits, fluids, tune-ups or adjustments;
e) this warranty will not apply where damage is caused by repairs made or attempted by others (i.e.
persons not authorized by the manufacturer);
CORDED DRILL - 054-1213-0
CORDED DRILL - 054-1213-0
WARRANTY
WARRANTY
19
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising