Instruction Manual Evenflo Titan 65
SureRideTM/Titan®65
Child Restraint System
Owner’s Manual
Keep for future use.
Rear-facing
2.3 to 18 kg
(5 to 40 lbs)
48 to 102 cm
(19 to 40 in.)
Forward-facing
10 to 29.4 kg
(22 to 65 lbs)
71 to 137 cm
(28 to 54 in.)
Para instrucciones en Español,
llamar al: 1-800-233-5921
WARNING:
To reduce the risk of serious injury
or death, read this owner’s manual prior
to installing and using this child restraint.
© 2014 Evenflo Company
25701223
1/14
More children are killed every year as passengers in
car crashes than by any other type of injury.
To reduce the risk of SERIOUS INJURY or DEATH, read this
owner’s manual and your vehicle owner’s manual before installing and using this child restraint. Using a child restraint
makes a big difference. By properly using this child restraint
and following these instructions (and the instructions that
accompany your vehicle), you will greatly reduce the risk of
serious injury or death to your child from a crash. Do not
be misled by the commonly used term “safety seat;” no
restraint system can prevent all injuries in all crashes. Many
properly restrained adults and children are injured in motor
vehicle crashes, including relatively minor crashes. A properly used child restraint is the best way to minimize injuries
to your child and to increase the chances for your child’s
survival in most crashes.
Table of Contents
Premature Infant Use..........................................................2
Warnings........................................................................... 3
Safe Practices..................................................................... 7
Recall Information for U.S. Customers................................ 8
Public Notice for Canadian Customers............................... 8
Motor Vehicle/Aircraft Usage............................................. 9
LATCH Information.............................................................9
Symbol Legend...................................................................9
Care and Cleaning........................................................... 10
Storing Your Instructions.................................................. 10
Visual Glossary................................................................. 12
Using the SureRide™ Rear-facing...........................14
Using the SureRide Forward-facing........................16
Installation
Rear-facing Using a Seat Belt ........................................ 18
Rear-facing Using the LATCH System ............................ 21
Forward-facing Using a Seat Belt.................................... 25
Installing Tether Strap.................................................... 27
Forward-facing Using the LATCH System....................... 28
Positioning the Harness Strap.......................................... 32
Adjusting the Recline Stand............................................. 34
Using the Locking Clip..................................................... 36
Securing Your Child......................................................... 38
Adjusting the Crotch Strap.............................................. 39
Adjusting the Harness Strap............................................. 40
Removing Your Child from the Restraint.......................... 41
Removing the Tether Strap.............................................. 41
Removing the LATCH System........................................... 42
Installing the Accessories.................................................. 44
Securing Your Child Restraint in Aircraft............................46
Installing Child Restraint Rear-facing in Aircraft.................46
Installing Child Restraint Forward-facing in Aircraft...........49
Replacement Parts........................................................... 51
Limited Warranty............................................................. 52
U.S. REGULATORY NOTICE
This child restraint meets all applicable requirements of
Federal Motor Vehicle Safety Standard 213.
For Canadian Models
CANADIAN REGULATORY NOTICE
This child restraint meets all applicable requirements of
Canadian Motor Vehicle Safety Standards CMVSS 213
and 213.1.
Child Requirements
• No restraint can guarantee absolute protection from
injury in every crash.
• This child restraint is designed for use by children in
rear-facing and forward-facing positions. To use this
child restraint properly, children MUST meet weight/
size specifications as follows:
For Rear-facing Use
• 2.3 to 18 kg (5 to 40 lbs)
• 48 to 102 cm (19 to 40 inches)
• Top of head is at least 25 mm (1 inch) below
the top of the child restraint seat back.
The American Academy of Pediatrics recommends
that children ride in the rear-facing position to
the highest weight or height allowed by the child
restraint.
Note: Once your child exceeds 18 kg (40 lbs)
OR the top of their head is within 25 mm
(1 inch) of the top of the child restraint seat
back, you MUST use this child restraint in the
forward-facing position.
For Forward-facing Use
• 10 to 29.4 kg (22 to 65 lbs)
• 71 to 137 cm (28 to 54 inches) AND the tops of the
child’s ears are at or below the child restraint seat
back.
• At least one year of age
Note: Once your child exceeds 29.4 kg (65 lbs)
OR is taller than 137 cm (54 inches), they can
no longer safely use this child restraint, and
you should consider using a booster seat.
1
PREMATURE INFANT USE
Before using this child restraint for preterm or low
birth weight infants you must read and follow the
guidelines in this section.
According to the U.S. National Highway Traffic Safety
Administration, a properly installed child restraint reduces the risk of death by over 70 percent for infants
involved in crashes. Federal Motor Vehicle Safety
Standard (FMVSS) 213 establishes design and
dynamic performance requirements for child restraint
systems. However, the standard has no minimum
weight limit and does not address the special
medical needs of preterm or low-birth weight infants.
To ensure that preterm and low-birth weight infants
are transported safely, the guidelines published by the
American Academy of Pediatrics (AAP) in Pediatrics
2009;123:1424–1429 must be followed.
All children should ride rear-facing in the vehicle
as long as possible. Preterm and low-birth weight
infants are at additional risk of breathing difficulties
and heart problems when placed in a child restraint.
Evenflo requires that the evaluation recommended
by the AAP be conducted for all infants born earlier
than 37 weeks and all newborn infants who weigh
less than 5 pounds at birth before their first car trip to
check for breathing difficulties or heart rate problems
when traveling in a rear-facing child restraint.
The AAP recommends that appropriate hospital staff
observe your infant in the child restraint for a
period of 90 to 120 minutes or the duration of travel,
whichever is longer. This period of observation must
be performed with the infant properly positioned
as described in these instructions and with the child
restraint placed at an angle that is approved for use
in the vehicle. The hospital staff will check for any
breathing difficulties or heart rate problems. Your
child’s pediatrician will let you know if there are
any special considerations for travel. The number of
trips and the duration of time the infant is seated in
the child restraint should be minimized. A caregiver
should ride in the back seat to monitor the infant
during travel.
You can learn more about the AAP’s recommendations
for observation of newborns and the guidelines for
safe transportation of preterm and low-birth weight
infants, as well as other resources for parents and
medical professionals, at
http://www.aap.org/healthtopics/carseatsafety.cfm.
2
WARNING
Air Bag Warnings
• DO NOT use this child restraint in the front seat of a
vehicle equipped with an air bag, unless the air bag has
been deactivated. Air bags may cause serious injury or
death to children under 12. If your vehicle has an air
bag, please refer to your vehicle owner’s manual for child
restraint installation.
• If the rear seat of your vehicle is equipped with side air
bags, refer to the following information for proper usage:
Vehicles built prior to the 2002 model year: DO NOT
use this restraint in a vehicle seating position equipped
with a side air bag unless authorized by the vehicle
manufacturer.
Model year 2002 and newer vehicles: Refer to your
vehicle owner’s manual before placing this restraint in a
seating position equipped with a side air bag. DO NOT
place any objects between the restraint and the side air
bag, as an expanding air bag may cause the items to
strike your child.
3
WARNING
Location Warnings
• According to statistics, children are safer when properly
restrained in a rear seating position than in the front
seating position. Generally, the center rear position is safest and should be used if available.
• ONLY use this child restraint on forward-facing vehicle
seats. DO NOT use this restraint with vehicle seats that
face the rear or side.
• ONLY use this child restraint on vehicle seats with backs
that lock into place.
• Some child restraints do not fit all vehicles or all seating
locations. There are many thousands of combinations of
vehicle makes, models, child restraint configurations, seat
belt designs, and seat cushion shapes. The easiest way
to determine whether your child restraint is suitable for
a particular seating position is to check for a tight
installation. If the child restraint cannot be properly
installed, DO NOT use the child restraint. Consult vehicle
owner’s manual, try a different seating location, or call
Evenflo at 1-800-233-5921 (U.S.) or 1-937-7733971 (Canada).
Premature Infants
• DO NOT use this or any child restraint with a premature infant until after consulting your doctor. Premature
infants may have difficulty breathing when in a sitting
position.
Rear-facing Warnings
• DO NOT use this child restraint rear-facing in a vehicle
equipped with lap belts that only lock during a sudden
stop or crash (emergency locking retractors). You must
use a seating location with a locking seat belt. Check
your vehicle owner’s manual to see if you have emergency
locking retractors.
• When using this restraint rear-facing, DO NOT loosen
the vehicle seat belt to provide more leg room, as this will
prevent the child restraint from protecting your child.
• DO NOT use the top two sets of harness slots rear-facing.
The harness may not properly restrain the child during a
crash.
• The headrest on the vehicle seat that the child faces
should be placed in the lowest position. The vehicle seat
back must be fully padded and free of any hard objects.
• Fold-down armrests could pose a hazard to a rear-facing
child in certain types of collisions. Consult your vehicle
owner’s manual before installing any rear-facing child
restraint in front of a fold-down armrest.
4
WARNING
• NEVER turn a child restraint forward-facing with an
infant who weighs less than 10 kg (22 lbs) or who is less
than one year of age. Crash forces may cause serious
neck injury or death.
Forward-facing Warnings
• If your child weighs more than 29.4 kg (65 lbs) or his/her
shoulders are above the highest harness level, you MUST
discontinue using this child restraint, as it may no longer
adequately protect your child.
• DO NOT use the three sets of lower harness slots
forward-facing. The harness may not properly restrain
the child during a crash.
Seat Belt Warnings
• DO NOT use this child restraint in a vehicle with doormounted seat belts.
• DO NOT use this child restraint in a vehicle with seat
belts that automatically move along the vehicle frame
when the door is opened. These seat belts will not hold a
child restraint properly.
• Use only with vehicle seat belts that can be pulled tight
and will stay locked.
• DO NOT use this child restraint if it moves more than
25 mm (1 inch) forward or side-to-side at the belt path.
Serious injury or death may result from poor installation.
Move the child restraint to another seating location.
• DO NOT allow the seat belt release button to touch the
child restraint. Accidental contact may cause the seat belt
to release. If necessary, turn the seat belt release button
away from the child restraint or move the child restraint
to a different location.
• Failure to adjust the harness or seat belts snugly around
your child may result in your child striking the vehicle’s
interior during a sudden stop or crash. Serious injury or
death may occur.
• If the vehicle seat belts are not routed and fastened
correctly, the child restraint may not protect your child in
a crash.
• Remove locking clip from vehicle seat belt when not used
with a child restraint, or the vehicle seat belt will not
properly restrain an adult or child. Serious injury could
occur.
LATCH (Lower Universal Anchorage System [UAS]
or Isofix) Warnings
• ONLY use for securing child restraint to lower LATCH
anchor points.
5
WARNING
LATCH (Lower Universal Anchorage System [UAS]
or Isofix) Warnings – cont.
• ALWAYS read and follow exactly the instructions that
accompany your vehicle and child restraint.
• Do not use the lower anchors of the child restraint
anchorage system (LATCH System) to attach this child
restraint when restraining a child weighing more than
22.7 kg (50 lbs.) with the internal harnesses of the child
restraint.
• NEVER attach two hooks to one vehicle lower anchor
point.
• DO NOT use the vehicle seat belts to install a child restraint when using the LATCH system.
• ONLY use the LATCH system as described in these
instructions. Serious injury or death may result from
misuse.
• ALWAYS be sure that the LATCH hook is fully engaged
onto the LATCH anchor point by pulling hard on the
LATCH strap. If it is not totally engaged, the LATCH system will not secure your child restraint. Serious injury or
death may result.
• DO NOT use this child restraint if it moves more than 25
mm (1 inch) forward or side-to-side at the belt path. Serious injury or death may result from poor installation. Try
again or use the vehicle belts to install the child restraint.
• To avoid a strangulation hazard, you MUST store the
unused LATCH assembly, with all slack removed, in the
storage area on the back of the seat. Roll or fold the
excess LATCH strap and secure with a rubber band to
prevent serious injury to vehicle occupants.
• In addition to these instructions, read and follow your
vehicle owner’s manual regarding installation of child
restraints and LATCH. If there is a discrepancy, follow
your vehicle owner’s manual.
Top Tether Warnings
• Failure to secure the top tether strap (provided) as
specified in these instructions could result in serious injury.
• The top tether strap MUST be used if your vehicle has
a plain lap belt that only locks during a sudden stop or
crash (emergency locking retractors) AND/OR if your
vehicle has seat belts whose buckles extend from a slot
in the vehicle seat cushion in front of the crease where
the seat and back cushions meet. Otherwise, the child
restraint cannot be installed tightly, increasing the risk of
injury to your child. Check your vehicle owner’s manual
6
WARNING
to see if your vehicle has emergency locking retractors.
• To avoid a strangulation hazard, you MUST tightly roll
or fold excess tether strap and secure with the strap/
rubber band. Attach the tether hook to the storage clip
when not in use. This will keep an unused tether from
hitting someone during a crash.
Additional Warnings
• DO NOT use child restraint if it is damaged, broken, or
missing parts.
• DO NOT use this restraint if it has been involved in a
crash. It must be replaced.
• NEVER leave child unattended.
• In hot or sunny weather, ALWAYS check the seat, buckle,
LATCH hooks, and adjuster for hot areas before placing a
child into the child restraint. Your child could be burned.
Cover the child restraint with a light colored blanket
when you leave the vehicle.
• This child restraint must be securely belted to the vehicle
at all times. An unsecured child restraint may injure
someone if a crash occurs.
• DO NOT attach additional padding, toys, or other
devices not made by Evenflo to the child restraint. Items
not tested with the child restraint could injure the child.
• Failure to follow installation instructions could result in
serious injury or death. These instructions and the instructions in your vehicle owner’s manual must be
followed carefully. If there is a conflict between the two,
the vehicle owner’s manual regarding child restraint
installation must be followed.
• In cold weather, DO NOT dress the child in bulky clothing like snowsuits if the child is riding in a child restraint.
Bulky coats/snowsuits make it difficult to properly tighten
the harness to the child, which may allow the child to be
ejected from the restraint during a crash.
Safe Practices
• Everyone rides buckled up or the vehicle does
not go. Make no exceptions for adults or children. If
someone unbuckles, stop the vehicle. Being firm and
consistent from the start will mean fewer discipline
problems as children get older. An unrestrained person
can be thrown into and injure other passengers.
• Many safety advocates and healthcare professionals
recommend that children ride rear-facing for as long as
possible. See limitations recommended on rear-facing
use on page one.
7
• NEVER try to tend to a crying baby’s needs while
driving. NEVER take a baby out of a child restraint for
comforting while the vehicle is moving.
• DO NOT allow a child in a vehicle to have objects such
as lollipops or ice cream on a stick. The object can
injure the child if the vehicle swerves or hits a bump.
• DO NOT feed an infant who is riding in a child
restraint.
• Put sharp or heavy items in the trunk. Anything loose
can be deadly in a crash.
• Dress the child in clothing with legs. Since the
harness must pass between the child’s legs, clothing
with legs permits a tighter fit.
• In hot, sunny weather, cover the seat and buckle with
a light colored blanket when you leave the vehicle.
• For child restraints equipped with leather seat pads,
cover your seat with a blanket in warm weather.
Leather can become very hot in direct sunlight.
• In cold weather, a child may need an extra blanket
for warmth. Secure the child in the child restraint and
cover both the child and the restraint with a blanket.
Recall Information for U.S. Customers
• Child restraints could be recalled for safety reasons.
You must register this restraint to be reached in a recall.
Send your name, address, and the restraint’s model
number and manufacturing date to Evenflo Company,
Inc., 1801 Commerce Dr., Piqua, OH 45356 or call
1-800-233-5921. You may also register online at:
www.evenflo.com/registercarseat.
• For recall information, call the U.S. Government’s Vehicle
Safety Hotline at 1-888-327-4236 (TTY:1-800-4249153) or go to: http://www.NHTSA.gov.
Public Notice for Canadian Customers
• Child restraints could be recalled for safety reasons.
You must register this restraint to be reached in a recall.
Send your name, address, and the restraint’s model
number and manufacturing date to Evenflo Company,
Inc., 1801 Commerce Dr., Piqua, OH 45356, call
1-937-773-3971, or register online at:
www.evenflo.com/registercarseatcanada.
• For public notice information, call Transport Canada at
1-800-333-0510 (1-613-993-9851 in Ottawa region).
8
Motor Vehicle/Aircraft Usage
When used with the internal
harness and properly installed
pursuant to these instructions,
this restraint is certified for use only
in passenger and multi-purpose
Check with
passenger motor vehicles, buses,
your
airline before
and trucks equipped with Type I
departure to make sure
or II seat belts and in aircraft.
Tip
ip!!
Airplane installation is the same
as Type I vehicle installation. Turn
the top of the airplane seat belt
buckle away from the restraint for
easy release and removal.
this restraint meets
their requirements.
Refer to pages 46 to 50 for instructions on installing your
child restraint in aircraft.
LATCH Information
“LATCH” (Lower Anchors and Tethers for CHildren) is
a system for attaching the child restraint to your vehicle
seat. It can be used in place of the seat belts in vehicles
with LATCH anchors. Refer to your vehicle owner’s
manual for the locations of LATCH anchors.
Note: Your vehicle owner’s manual may refer to this system as “Universal Anchorage System,” “Lower Universal
Anchorage System,”or ”ISOFIX.”
Symbol Legend
Air Bag Symbol – Alerts you to important
information about air bag safety.
LATCH Symbol – Alerts you to important
information about LATCH safety.
Tether Anchor Symbol – Alerts you to
important information about tether anchor
safety.
9
Care and Cleaning
• To help protect the vehicle upholstery, place a towel
beneath and behind the child restraint.
• Plastic and metal parts may be wiped clean with mild
soap and water and dried with a soft cloth.
Do not use abrasive cleaners or solvents.
• Take care not to damage any labels.
• The harness can be wiped clean with mild soap and
water. Allow harness to air dry. DO NOT immerse
buckle in water or lubricate buckle.
• Machine wash the seat pad separately in cold water,
delicate cycle, and tumble dry 10 to 15 minutes on
low heat.
• NEVER use child restraint without the seat pad.
• Leather pads (not available on all models) may be
cleaned. For best results spot clean with mild soap
and water or with a mixture of 10 parts water to
1 part mild alcohol. Allow to air dry. DO NOT
MACHINE WASH.
Storing Your Instructions
After thoroughly reading and
following these instructions,
store the instructions in the
clips on the sides of your
child restraint.
For future reference, record the model number of your
child restraint AND the date of manufacture below.
Model Number:
Date of Manufacture:
10
This page is intentionally blank.
11
Visual Glossary
Your vehicle components may be significantly different than
pictured. Consult your owner’s manual to help you identify
your vehicle components.
Fold-down Armrest
Consult your vehicle’s owners manual.
Back Seat
Belt Buckles
Tether Anchors
Forward-facing
ONLY
Center Lap
Belt
Back Seat
Retractor
Lap/Shoulder
Belt
LATCH
Anchors
Seat Crease
IMPORTANT: If your vehicle has side air bags, please refer to
the warnings on page 3.
Top 2 Harness
Positions for
Forward-facing
ONLY
Front View
Chest Clip
For U.S.
Customers:
This set of harness
slots can be for
either forwardfacing or rearfacing use.
For Canadian
Customers:
This set of harness
slots can ONLY be
used forwardfacing.
Harness
Straps
Seat Pad
Crotch Strap
Harness
Release Button
Bottom 3
Harness Positions
for Rear-facing
Crotch Buckle
ONLY
Harness Adjuster
Strap
12
Visual Glossary
Front Seat Lap and Shoulder Belts
Headrests
Must be in the lowest
position where the child
restraint is located.
10
4
30
20
12
0
A
IR
B
A
G
Important
Front Seat Retractor
Consult your vehicle
owner’s manual to determine
proper placement of child restraint
in your vehicle and familiarize
yourself with your vehicle’s
components.
LATCH Hook
Back View
Tether Strap
and Hook
Top 2 Harness
Positions for
Forward-facing
ONLY
Instruction
Storage Area
For U.S.
Customers:
This set of harness
slots can be for
either forwardfacing or rearfacing use.
For Canadian
Customers:
This set of harness
slots can ONLY be
used forwardfacing.
LATCH Hook
Harness Straps
Locking Clip
Note: Recline Stand
is nested below child
restraint.
Splitter Plate
13
Bottom 3
Harness Positions
for Rear-facing
ONLY
Using the SureRide™
Rear-facing
Child Requirements:
• Weight: 2.3 to 18 kg (5 to 40 lbs)
• Height: 48 to 102 cm (19 to 40 inches) AND the
top of child’s head is at least 25 mm (1 inch) below
top of the child restraint seat back.
Note: Once your child exceeds 18 kg (40 lbs) OR the
top of their head is within 25 mm (1 inch) of the top of
the child restraint seat back, you MUST use this child
restraint in the forward-facing position.
14
WARNING
When using this restraint rear-facing, DO NOT loosen
the vehicle seat belt to provide more leg room, as this
will prevent the child restraint from protecting your child.
1.Secure child restraint to the vehicle seat.
• Recline stand is flipped to the recline position
(page 34).
• Install with vehicle seat belt (page 18) or LATCH
system (page 21).
• Towel rolled up and placed beneath the recline
stand, if necessary (page 36).
• Install locking clip, if necessary (page 36).
2.Set the child in the child restraint.
Top of head is at least 25 mm (1 inch) below the
top of the child restraint seat back (page 1).
3.Fasten the buckle. Refer to page 38.
4.Make necessary adjustments.
• Crotch strap is snug against the child (page 39).
• Harness straps MUST be snug against the child’s
shoulders, with no slack (page 38).
5.Position and connect chest clip.
Chest clip/harness tie MUST be at armpit level
(page 38).
6.Check your work.
• Recline stand is flipped to the recline position
(page 34).
• The child restraint DOES NOT move more than
25 mm (1 inch) forward or side-to-side (pages
20 and 24).
• The child’s back and bottom are flat against the
back and bottom surfaces of the child restraint
(page 38).
• Shoulder harness straps MUST start at or below
shoulder height using the strap slots closest to
your child’s shoulders (page 32).
• Buckle tongues are fully engaged (page 38).
• The level arrow is level with the ground (pages
18 and 22).
15
Using the SureRide
Forward-facing
Child Requirements:
• Weight: 10 to 29.4 kg (22 to 65 lbs)
• Height: 71 to 137 cm (28 to 54 inches) AND the
tops of the child’s ears are at or below the child
restraint seat back.
• Age: At least one year of age
Note: Once your child exceeds 29.4 kg (65 lbs) OR is
taller than 137 cm (54 inches), they can no longer safely
use this child restraint, and you should consider using
a booster seat.
16
WARNING
If your child weighs more than 29.4 kg (65 lbs) or their
shoulders are above the highest harness level, you MUST
discontinue use, or the child restraint will not protect
your child.
1.Secure child restraint to the vehicle seat.
• Recline stand is flipped to the upright position
(page 34).
• Install with vehicle seat belt (page 25) or LATCH
system (page 28).
• Canadian consumers: Install tether strap (pages 27
and 31).
• Install locking clip, if necessary (page 36).
2.Set the child in the child restraint.
Tops of the child’s ears are at or below the child
restraint seat back (page 1).
3.Fasten the buckle. Refer to page 38.
4.Make necessary adjustments.
• Crotch strap is snug against the child (page 39).
• Harness straps MUST be snug against the child’s
shoulders, with no slack (page 38).
5.Position and connect chest clip.
Chest clip/harness tie MUST be at armpit level
(page 38).
6.Check your work.
• Recline stand is flipped to the upright position
(page 34).
• The child restraint DOES NOT move more than
25 mm (1 inch) forward or side-to-side (pages
26 and 30).
• The child’s back and bottom are flat against the
back and bottom surfaces of the child restraint
(page 38).
• Shoulder harness straps MUST start at or above
shoulder height, AND you must use the strap
slots closest to your child’s shoulders (page 32).
• Buckle tongues are fully engaged (page 38).
17
Installing Your Child Restraint
Rear-facing Using a Seat Belt
WARNING
1
NEVER turn a child restraint
forward-facing with an infant
who weighs less than 10 kg
(22 lbs) or who is less than one
year of age.
Crash forces may cause serious
injury or death.
ARROW MUST BE LEVEL WITH
GROUND WHEN USED REAR-FACING
ARROW MUST BE LEVEL WITH
GROUND WHEN USED REAR-FACING
A
REAR OF VEHICLE
REAR OF VEHICLE
Infants MUST always ride facing the rear of the
vehicle. The back of the child restraint supports and
protects the baby and absorbs crash forces.
Adjust the child restraint to the recline position (page
34). Place the child restraint in your vehicle rearfacing. Adjust the restraint so that the level arrow A
is level with the ground.
2
Attach the harness
straps B to the splitter
plate C using the infant
position (page 33) on
the harness straps.
As your child grows, you
can attach the harness
straps B to the splitter
plate using the pockets
at the end of the straps.
C
B
18
B
3
WARNING
DO NOT use the two upper harness slots rear-facing. The
harness may not properly restrain the child during a crash.
Make sure the harness
straps are in one of the
three lower strap slots D.
The harness straps should
start at shoulder height or
lower, using the strap slots
closest to your child’s
shoulders E, as shown.
F
D
E
U.S. Customers Only: For a taller child, the fourth
set of harness slots F can be used. Note: These slots
MUST start at shoulder height or lower and be the
closest slots to your child's shoulders.
4
Lap & Shoulder
Belt Combination
Lap Belt Only
H
H
I
I
G
G
Pull the seat pad off of the front of the child restraint.
Route the vehicle seat belt G through the rear-facing
belt path H and continue through the opposite
opening of the child restraint. IMPORTANT: Make
sure the seat belt G is in front of the crotch strap I,
as shown. Fasten the vehicle seat belt depending on
your type of seat belt.
Note: Some ELR vehicle belts can be switched so that
they lock when tightened. It may not be necessary to
use a locking clip in these situations. To install a locking
clip, refer to page 36. Refer to vehicle owner’s manual to
determine which type of belt retractor is in the vehicle.
19
5
G
H
WARNING
• If vehicle seat belts are not routed and fastened
correctly, the child restraint may not protect your
child in a crash.
• DO NOT use this child restraint if it moves more than
25 mm (1 inch) forward or side-to-side at the vehicle
belt path. Serious injury or death may result from
poor installation. If you cannot tightly secure the child
restraint, try again or move it to another location.
The seat belt must be as tight as possible.
Put your full weight onto the child restraint as you
tighten the seat belt G.
Check your work. If you can move the child restraint
more than 25 mm (1 inch) forward or side-to-side at
the belt path H, the seat belt is not tight enough,
and you MUST try again.
20
Installing Your Child Restraint
Rear-facing Using the LATCH System
LATCH is a system for attaching the child restraint to
your vehicle seat. It is to be used in place of your
vehicle’s seat belts and can be used in vehicles with
LATCH anchors. Your vehicle owner’s manual may
refer to this system as ISOFIX, Universal Anchorage
System (UAS), or Lower Universal Anchorage System.
WARNING
• ONLY use for securing child restraint to lower LATCH
anchor points.
• ALWAYS read and follow exactly the instructions that
accompany your vehicle and child restraint.
• NEVER attach two hooks to one vehicle lower anchor
point.
• DO NOT use the vehicle seat belts to install a child
restraint when using the LATCH system.
• ONLY use the LATCH system as described in these
instructions. Serious injury or death may result from
misuse.
• ALWAYS be sure that the LATCH hook is fully
engaged onto the LATCH anchor point by pulling
hard on the LATCH strap. If it is not totally engaged,
the LATCH system will not secure your child restraint.
Serious injury or death may result.
• To avoid a strangulation hazard, you MUST store the
unused LATCH assembly, with all slack removed, in the
storage area on the back of the seat. Roll or fold the
excess LATCH strap and secure with a rubber band to
prevent serious injury to vehicle occupants.
• In addition to these instructions, read and follow your
vehicle owner’s manual regarding installation of child
restraints and LATCH. If there is a discrepancy, follow
your vehicle owner’s manual.
21
1
WARNING
NEVER turn a child restraint
forward-facing with an infant
who weighs less than 10 kg (22 lbs)
or who is less than one year of age.
Crash forces may cause serious
injury or death.
ARROW MUST BE LEVEL WITH
GROUND WHEN USED REAR-FACING
A
REAR OF VEHICLE
ARROW MUST BE LEVEL WITH
GROUND WHEN USED REAR-FACING
REAR OF VEHICLE
Infants MUST always ride
facing the rear of the vehicle.
The back of the child restraint supports and protects
the baby and absorbs crash forces.
Adjust the child restraint to the recline position (page
34). Place the child restraint in your vehicle rearfacing. Adjust the restraint so that the level arrow A
is level with the ground.
2
Attach the harness straps B
to the splitter plate C using
the infant position (page
33) on the harness straps.
As your child grows, you
can attach the harness
straps B to the splitter plate
using the pockets at the end
of the straps.
C
B
3
E
F
D
B
Pull seat pad from front of
child restraint.
Route the LATCH strap D
through the rear-facing
belt path E.
IMPORTANT: Make sure
the LATCH strap D is in
front of the crotch
strap F, as shown.
22
4
WARNING
DO NOT use the two upper harness slots rear-facing. The
harness may not properly restrain the child during a crash.
Make sure the harness
straps are in one of the
three lower strap slots G.
The harness straps should
start at shoulder height or
lower, using the strap slots
closest to your child’s
shoulders H, as shown.
I
G
H
U.S. Customers Only: For a taller child, the fourth set
of harness slots I can be used.
Note: These slots MUST start at shoulder height or
lower and be the closest slots to your child's shoulders.
5
Know Your LATCH
The LATCH system that comes with your child
restraint will be one of the two types below.
SecureRight™
Quick Connector™
Strap
Adjuster
Clip
Hook
Strap
Adjuster
K
L
J
J
J
Refer to your owner’s manual to locate the lower
anchors J on your vehicle seat. Attach the right
hook K, or clip L, to the right anchor J and the
left hook, or clip, to the left anchor. DOUBLE CHECK
that the LATCH hook is fully engaged by pulling hard
on the LATCH strap.
23
6
E
E
WARNING
DO NOT use this child restraint if it moves more than
25 mm (1 inch) forward or side-to-side at the vehicle
belt path. Serious injury or death may result from poor
installation. If you cannot tightly secure the child restraint, try again or move it to another location.
The LATCH assembly must be as tight as possible. Using your full weight, push the child restraint
firmly onto the vehicle seat while pulling up on the
LATCH strap to tighten.
Check your work. If you can move the child restraint more than 25 mm (1 inch) forward or sideto-side at the belt path E, the LATCH assembly is
not tight enough. You will need to try again or find
another location for your child restraint.
To remove the LATCH system, go to page 42.
24
Installing Your Child Restraint
Forward-facing Using a Seat Belt
1
WARNING
DO NOT use the three lower harness slots
forward-facing. The harness may not properly
restrain the child in the event of a crash.
A
A
B
2
Make sure that the harness
straps are in one of the three
upper strap slots A and
the splitter plate is attached
to the bottom of the harness
strap in the toddler position B (page 33). This will
provide more room for your
toddler to fit comfortably.
Adjust the child restraint to
the upright position (page
34). Place the child restraint
in your vehicle forwardfacing.
3
WARNING
C
If the vehicle belts are not
routed and fastened correctly, the child restraint
may not protect your child
in a crash.
Thread the vehicle seat
belt C through the child
restraint.
Note: Lift the pad away for
easier access.
25
4
Lap Belt Only
Lap & Shoulder Belt
Fasten the vehicle seat belt as shown, depending on
your type of seat belt.
Note: Some ELR vehicle belts can be switched so that
they lock when tightened. It may not be necessary to
use a locking clip in these situations. To install a locking
clip, refer to page 36. Refer to vehicle owner’s manual to
determine which type of belt retractor is in the vehicle.
5
C
D
WARNING
DO NOT use this child restraint if it moves more than
25 mm (1 inch) forward or side-to-side at the vehicle
belt path. Serious injury or death may result from
poor installation. Move the child restraint to another
seating location or try to tighten the seat belt again.
The seat belt must be as tight as possible.
Put your full weight onto the seat as you tighten the
seat belt C.
Check your work. If you can move the child restraint
more than 25 mm (1 inch) forward or side-to-side at
the vehicle seat belt path D, the seat belt is not tight
enough, and you will need to try again.
26
6
WARNING
• Failure to follow these instructions could result in
serious injury to your child or other vehicle
occupants.
• The tether strap is for forward-facing use only.
E
F
G
Attach tether hook E
to the tether anchor
bracket F in your
automobile.
Pull the end of the
strap G to tighten.
Remove all slack in
the strap.
WARNING
• To avoid a strangulation hazard, you MUST tightly
roll or fold excess tether strap and secure with the
strap/rubber band.
• Attach the tether hook to the storage clip when not
in use. This will keep an unused tether from hitting
someone during a crash.
After adjusting the top tether strap, you may have
excess strap; DO NOT cut it off. If you do, it may not
be long enough to use in another vehicle. Instead,
tightly roll up the excess tether strap and place the
rubber band around the bundle.
Note: Refer to your vehicle owner’s manual for the
location of the tether anchor bracket in your vehicle.
Older vehicles may not come equipped with anchor
bracket hardware. Check with your vehicle dealer.
If you have questions regarding tether anchors that
are not addressed by the vehicle owner’s manual or
answered by an authorized dealer/vehicle manufacturer, call Evenflo’s ParentLink at 1-800-233-5921
(U.S.) or 1-937-773-3971(Canada).
27
Installing Your Child Restraint
Forward-facing Using the LATCH System
LATCH is a system for attaching the child restraint
to your vehicle seat. It is to be used in place of your
vehicle’s seat belts and can be used in vehicles with
LATCH anchors. Your vehicle owner’s manual may refer
to this system as ISOFIX, Universal Anchorage System
(UAS), or Lower Universal Anchorage System.
IMPORTANT: Use vehicle belt (not LATCH connectors) for internal harness installations with children weighing more than 22.7 kg (50 lbs.).
WARNING
• ONLY use for securing child restraint to lower LATCH
anchor points.
• ALWAYS read and follow exactly the instructions that
accompany your vehicle and child restraint.
• Do not use the lower anchors of the child restraint anchorage system (LATCH System) to attach this child restraint
when restraining a child weighing more than 22.7 kg (50
lbs.) with the internal harnesses of the child restraint.
• NEVER attach two hooks to one vehicle lower anchor
point.
• DO NOT use the vehicle seat belts to install a child restraint when using the LATCH system.
• ONLY use the LATCH system as described in these
instructions. Serious injury or death may result from misuse.
• ALWAYS be sure that the LATCH hook is fully engaged
onto the LATCH anchor point by pulling hard on the
LATCH strap. If it is not totally engaged, the LATCH system
will not secure your child restraint. Serious injury or death
may result.
• DO NOT use this child restraint if it moves more than 25
mm (1 inch) forward or side-to-side at the belt path. Serious injury or death may result from poor installation. Try
again or use the vehicle belts to install the child restraint.
• To avoid a strangulation hazard, you MUST store the
unused LATCH assembly, with all slack removed, in the
storage area on the back of the seat. Roll or fold the excess
LATCH strap and secure with a rubber band to prevent
serious injury to vehicle occupants.
• In addition to these instructions, read and follow your
vehicle owner’s manual regarding installation of child
restraints and LATCH. If there is a discrepancy, follow your
vehicle owner’s manual.
28
1
WARNING
DO NOT use the three lower harness slots forwardfacing. The harness may not properly restrain the child in
the event of a crash.
A
A
B
Make sure that the harness
straps are in one of the
three upper strap slots A
and the splitter plate is attached to the bottom of the
harness strap in the toddler
position B (page 33).
This will provide more
room for your toddler to
fit comfortably.
2
C
Adjust the child restraint to the upright position
(page 34) and place it in your vehicle forward-facing, as shown. Route the LATCH assembly through
each side of the forward-facing belt path C.
29
Know Your LATCH
2
3
The LATCH system that comes with your child
restraint will be one of the two types below.
SecureRight
Quick Connector
Strap
Adjuster
Clip
Hook
Strap
Adjuster
K
L
J
J
J
Refer to your owner’s manual to locate the lower anchors
J on your vehicle seat. Attach the right hook K, or clip
L, to the right anchor J and the left hook, or clip, to
the left anchor. DOUBLE CHECK that the LATCH hook is
fully engaged by pulling hard on the LATCH strap.
4
Ö
C
WARNING
DO NOT use this child restraint if it moves more than
25 mm (1 inch) forward or side-to-side at the vehicle
belt path. Serious injury or death may result from poor
installation. If you cannot tightly secure the child
restraint, try again or move it to another location.
The LATCH assembly must be as tight as possible. Using your full weight, push the child restraint firmly onto the
vehicle seat while pulling up on the LATCH strap to tighten.
Check your work. If you can move the child restraint
more than 25 mm (1 inch) forward or side-to-side at the
belt path C, the LATCH assembly is not tight enough. You
will need to try again or find another location for your child
restraint. To remove the LATCH system, go to page 42.
30
5
WARNING
• Failure to follow these instructions could result in
serious injury to your child or other vehicle occupants.
• The tether strap is for forward-facing use only.
F
G
H
Attach tether hook F
to the tether anchor
bracket G in your
automobile.
Pull the end of the
strap H to tighten.
Remove all slack in
the strap.
WARNING
• To avoid a strangulation hazard, you MUST tightly roll
or fold excess tether strap and secure with the strap/
rubber band.
• Attach the tether hook to the storage clip when not
in use. This will keep an unused tether from hitting
someone during a crash.
After adjusting the top tether strap, you may have
excess strap; DO NOT cut it off. If you do, it may not
be long enough to use in another vehicle. Instead,
tightly roll up the excess tether strap and place the
rubber band around the bundle.
Note: Refer to your vehicle owner’s manual for the
location of the tether anchor bracket in your vehicle.
Older vehicles may not come equipped with anchor
bracket hardware. Check with your vehicle dealer.
If you have questions regarding tether anchors that
are not addressed by the vehicle owner’s manual or
answered by an authorized dealer/vehicle manufacturer, call Evenflo’s ParentLink at 1-800-233-5921
(U.S.) or 1-937-773-3971(Canada).
31
Positioning the Harness Strap
U.S. Customers
Only:
ONLY
C Forward-facing
Top Two Harness
Positions
B
Rear-facing and
Forward-facing
This set of harness
slots can be for either
forward-facing or
rear-facing use.
U.S. and Canadian
Customers:
A
Rear-facing ONLY
Bottom Three
Harness Positions
Shoulder harness straps on this child restraint are
adjustable to six positions.
U.S. Customers Only: Rear-facing, the shoulder
harness straps MUST start at or below shoulder height
using the strap slots closest to your child’s shoulders in
one of the four lower harness positions A and B. The
child’s head MUST be at least 25 mm (1 inch) below
the top of the seat back.
Canadian Customers: Rear-facing, the shoulder
harness straps MUST start at or below shoulder height
using the strap slots closest to your child’s shoulders in
one of the three lower harness positions A. The child’s
head MUST be at least 25 mm (1 inch) below the top
of the seat back.
U.S. and Canadian Customers: Forward-facing, you
MUST use one of the top three harness positions B and
C. If the tops of the child’s ears are above the top of
the seat back, the child’s shoulders fall above the upper
harness slots, or the child weighs more than 29.4 kg (65
lbs), you MUST discontinue use of this child restraint.
We recommend that you move your child to a larger
child restraint or a booster seat. You MUST use the harness slots at or above the child’s shoulders AND closest
to your child’s shoulders.
32
1
Infant
D
F
E
Toddler
2
There are two positions
on the harness straps.
The top loop D is for
infant use. The bottom
pocket E is for use as
your child grows.
To change the harness
strap position, loosen
the shoulder harness
as shown on page
40, step 2. Slide the
harness strap off the
splitter plate F.
Pull harness strap through
to the front of the child
restraint.
Thread each harness strap
through the appropriate
slot. Pull the harness strap
to the back of the child
restraint.
3
Reattach the splitter
plate F to the
appropriate pocket
on the harness strap.
F
33
Adjusting the Recline Stand
Lift the child restraint and
flip the recline stand A,
located under the child
restraint seat, to either the
upright or recline position.
A
Note: Recline position is
to be used for rear-facing
ONLY.
Upright
Recline
FOR CANADIAN CONSUMERS ONLY:
A
Wrap Velcro® strap
around the recline
stand A and insert
the end of the strap
through the D-ring
B, as shown.
B
Pull tightly and
adhere Velcro to
itself, as shown.
34
A
C
C
To fold the recline stand A, turn the child restraint
upside down. Pull the shell walls away from the
locking tabs C on the sides of the recline stand and
rotate the recline stand downward until it lies flat, as
shown.
A
35
Rear-facing Recline
The child restraint MUST
be in the RECLINE position
for rear-facing infant use.
Child MUST weigh
2.3 to 18 kg (5 to 40 lbs).
ARROW MUST BE LEVEL WITH
GROUND WHEN USED REAR-FACING
REAR OF VEHICLE
D
ARROW MUST BE LEVEL WITH
GROUND WHEN USED REAR-FACING
If the level line is not
parallel to the ground, use
a tightly rolled towel or
small blanket D beneath
the front edge of the
recline stand.
REAR OF VEHICLE
Forward-facing Upright
The child restraint MUST
be in the UPRIGHT
position for forward-facing
toddler use.
Child MUST weigh
10 to 29.4 kg (22 to 65 lbs)
and be at least one year
of age.
Using the Locking Clip
To view a video about installing a locking clip, go to
www.evenflo.com.
Use the locking clip with:
• Lap/shoulder seat belt
combinations that have
a buckle tongue that
slides freely along the
belt without locking into
place; OR
•Seat belts equipped with an emergency locking
retractor (ELR). Some ELR vehicle belts can be
switched so that they lock when tightened. It may
not be necessary to use a locking clip in these
situations.
Locking Clip
Consult your vehicle
owner’s manual before
installing the locking
clip.
36
1
Rear-facing
Installation
Forward-facing
Installation
A
A
Using your full weight, press down on the child
restraint as you tighten the seat belt.
While holding the lap and shoulder belts together just
behind the free sliding buckle tongue A, unfasten the
seat belt.
2
Locking clip MUST
be placed within
13 mm (0.5 in.)
of buckle tongue.
B
Thread the locking clip B onto the seat belt and slide
it into place.
Re-buckle the seat belt. Locking clip must be placed
within 13 mm (0.5 inch) of buckle tongue.
WARNING
Remove locking clip from vehicle seat belt when not
used with a child restraint, or the vehicle seat belt will
not properly restrain an adult or child. Serious injury
could occur.
37
Securing Your Child
Place baby in the child restraint. The baby’s back and
bottom should be flat against the restraint. If there
is a gap, the baby will not be comfortable.
1
A
B
Bring each harness strap
over the child’s shoulders.
Insert the buckle tongues A
into the buckle.
Pull up on the harness strap
to check that the buckle
tongues are fastened.
Fasten the chest clip B
by snapping the two
halves together, as
shown.
Slide chest clip to armpit
level.
2
The harness straps must be snug against the child. A
snug strap should not allow any slack. It lies in a relatively straight line without sagging. It does not press
on the child’s flesh or push the child’s body into an
unnatural position. Check the harness straps near the
shoulders for slack. You should NOT be able to pinch
the harness (see illustration). Adjust as needed.
38
Adjusting the Crotch Strap
This Child Restraint Has Two Buckle
Harness Positions
B
A
B
A
To reposition the crotch strap, first turn the child
restraint upside down. Turn the crotch strap harness
anchor A sideways and push it through the slot in the
bottom of the seat shell B.
Reposition the harness anchor into the other slot.
Make certain the harness anchor is properly seated
against the seat shell B.
Note: The crotch strap should be snug against the
child. Choose the slot that is closest to the child AND
the most comfortable for the child but NEVER under
the child’s bottom.
For Newborn Position
Place the anchor A through the rear slot, then feed it
through the front slot.
A
A
Make sure the anchor is
completely through the front
slot and is lying flat against
the bottom of the seat.
IMPORTANT: Do not use this configuration for
infants weighing more than 4.5 kg (10 lbs).
39
Adjusting the Harness Strap
1
A
To tighten the harness straps, pull on the long harness
adjuster strap A on the front of the seat.
2
To loosen the harness
straps, push the
harness release
button B on the
front of the seat.
At the same time,
pull up on the
harness strap C near
the child’s shoulders.
C
B
40
Removing Your Child from the
Restraint
A
C
B
Push the release button A and pull the chest clip apart.
Press the red buckle release B and remove the buckle
tongues C.
Removing the Tether Strap
1
The tether strap that comes with your child
restraint will be one of the two types below.
A
B
Press the adjuster release
button B to loosen
tether strap.
Tilt the adjuster A and
slide the LATCH strap to
loosen.
2
D
C
41
Press the tab C and
twist, then remove
the hook from the
anchor D.
3
WARNING
• To avoid a strangulation hazard, you MUST tightly
roll or fold excess tether strap and secure with the
strap/rubber band.
• Attach the tether hook to the storage clip when not
in use. This will keep an unused tether from hitting
someone during a crash.
When the tether strap
is not in use, you
MUST attach the hook
E to the back of the
child restraint and
tightly roll and secure
the strap with the
strap/rubber band.
A loose tether strap
and hook may injure
your child.
E
Removing the LATCH System
1
A
Or
Tilt the adjuster A and
slide the LATCH strap to
loosen.
B
Press the adjuster release
button B to loosen LATCH
strap.
42
2
C
D
E
Or
To remove the hook C,
press the tab D and
twist, then remove from
anchor E.
F
G
E
To remove the clip F,
pull the red release
strap G and remove clip
from anchor E.
3
When the LATCH
system is not in
use, you MUST
attach the hooks C
to the back of the
child restraint.
A loose LATCH
strap and hook may
injure your child.
C
43
Installing the Accessories
Not available on all models.
A
B
A
WARNING
• Use the fold-down cup holder with the child restraint
in the forward-facing position ONLY.
• DO NOT use the accessories to store cans or hard
cups. Only for use with soft cups (such as styrofoam
or paper).
• DO NOT place any cups that contain hot liquids
(such as coffee or tea) in the cup holder.
• DO NOT snap any other items to this child restraint
unless it has been certified for use with this specific
child restraint.
To install the fold-down cup holder A, move seat
pad B out of the way and install the cup holder
onto the side of the restraint.
44
D
E
The optional Head Pillow
D attaches easily and helps
support the child’s head.
The optional Body Pillow E,
when placed in the restraint,
as shown, helps support
your child.
45
Securing Your Child Restraint in
Aircraft
The Federal Aviation Administration (FAA) recommends
that you secure your child for air travel in an appropriate child restraint based on your child’s weight and size.
Turbulence can happen with little or no warning. When
turbulence occurs, the safest place for your child is
in a properly installed child restraint, not in an
adult’s lap or on the aircraft seat with its seat
belt. Keeping your child in a child restraint during the
flight will help ensure your family arrives safely at your
destination.
The FAA recommends that a child weighing:*
• more than 18 kg (40 lbs) use an aircraft seat belt;
• less than 9 kg (20 lbs) use a rear-facing child restraint; and
• from 9 to 18 kg (20 to 40 lbs) use a forward-facing
child restraint.
* Please note that these FAA recommendations
may vary from those applicable to the use of
your child restraint in a motor vehicle.
IMPORTANT
You must use the internal harness when installing the
child restraint in aircraft.
Installing Child Restraint Rear-facing
in Aircraft
IMPORTANT: Before installing the child restraint, make
sure the aircraft seat is in a fully upright position.
1
ARROW MUST BE LEVEL WITH
GROUND WHEN USED REAR-FACING
REAR OF VEHICLE
Aircraft
Seat Belt
Adjust the child restraint to its recline position (page
34), then place it on the aircraft seat rear-facing, as
shown above.
46
Installing Child Restraint Rear-facing
in Aircraft
2
B
C
A
Pull the seat pad off the front of the child restraint.
Route the aircraft seat belt A through the rear-facing
belt path B opening on one side and continue
through the belt path opening on the opposite side
of the child restraint, as shown above.
IMPORTANT: Make sure the aircraft seat belt A is in
front of the crotch strap C, as shown above.
3
A
Fasten the aircraft seat belt A.
47
Installing Child Restraint Rear-facing
in Aircraft
4
D
B
A
The aircraft seat belt A must be as tight as possible.
Route the excess seat belt strap D back through the
rear-facing belt path B opening, as shown above. Using your full weight, push the child restraint firmly onto
the aircraft seat while pulling on the excess seat belt
strap to tighten.
Check your work. Reconnect the seat pad to the front
of the child restraint. Try to move the child restraint in
all directions. If you can move the restraint more than
25 mm (1 inch) forward or side-to-side at the rearfacing belt path B, the aircraft seat belt A is not tight
enough, and you MUST install again until the seat belt
is tight.
48
Installing Child Restraint Forward-facing
in Aircraft
IMPORTANT: Before installing the child restraint, make
sure the aircraft seat is in a fully upright position.
1
Aircraft
Seat Belt
Adjust the child restraint to its upright position (page
34), then place it on the aircraft seat forward-facing, as
shown above.
2
B
A
Route the aircraft seat belt A through the forward-facing belt path opening in the back of the child restraint
and continue through the belt path opening B on
the opposite side of the child restraint.
Note: Lift the restraint’s seat pad away for easier
access.
49
Installing Child Restraint Forward-facing
in Aircraft
3
A
Fasten the aircraft seat belt A.
4
D
C
The aircraft seat belt must be as tight as possible. Route
the excess aircraft seat belt strap C back through the
forward-facing belt path D opening, as shown above.
Using your full weight, push the child restraint firmly
onto the aircraft seat while pulling on the excess seat
belt strap to tighten.
Note: Because of the fixed length of aircraft seat belts, the
belt buckle could be behind the child’s back after tightening
the belt. For your child’s comfort, Evenflo recommends cushioning the child’s back by placing a small pillow or folded-up
blanket, or a folded-up jacket, over the belt buckle.
Check your work. Reconnect the seat pad to the front
of the child restraint. Try to move the child restraint in all
directions. If you can move the restraint more than 25
mm (1 inch) forward or side-to-side at the forward-facing belt path, the aircraft seat belt is not tight enough,
and you MUST install again until the seat belt is tight.
50
Replacement Parts
Not available on all models. Styles may vary.
To order replacement parts, you can order online at
www.evenflo.com or contact Evenflo. When you contact
us, please have the product model number and date of
manufacture (found on the back of the child restraint).
1 Locking Clip
2 Chest Clip
6 Tether
10 Body Pillow
3 Crotch Strap
7 Head Foam
8 Cup Holder
11 Seat pad
4 Harness
5 LATCH Assembly 9 Head Pillow
Proper Disposal of This Child Restraint
At the end of this child restraint’s useful life, Evenflo
encourages you to dispose of it properly. Most of the
components in this child restraint are recyclable.
1. Remove all fabric and padding.
2. Remove all screws and disassemble the restraint.
3. Recycle all plastic/foam parts and discard the rest.
If your local recycling center won’t accept the padding,
you may dispose of it in the landfill.
NOTE: Evenflo uses recycled materials in the manufacturing
process whenever possible but never for components that
are critical for safety.
51
Limited Warranty
For a period of 90 days from the original purchase of
this Product, Evenflo warrants to the original end user
(“Purchaser”) this Product (including any accessories)
against defects in material or workmanship. Evenflo’s
sole obligation under this express limited warranty
shall be, at Evenflo’s option, to repair or replace any
Product that is determined to be defective by Evenflo
and determined to be covered by this warranty.
Repair or replacement as provided under this warranty is the exclusive remedy of the Purchaser. Proof of
purchase in the form of a receipted invoice or bill of
sale evidencing that the Product is within the warranty period must be presented to obtain warranty
service. This express limited warranty is extended by
Evenflo ONLY to the original Purchaser of the Product
and is not assignable or transferable to subsequent
purchasers or end users of the Product. For warranty
service, contact Evenflo’s ParentLink Consumer
Resource Center.
EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE
LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON
THIS PRODUCT IS HEREBY DISCLAIMED. EVENFLO
SHALL NOT BE LIABLE FOR ANY INCIDENTAL,
CONSEQUENTIAL, SPECIAL OR PUNITIVE DAMAGES
OF ANY KIND FOR BREACH OF THE EXPRESS LIMITED
WARRANTY ON THIS PRODUCT, OR ANY WARRANTY
IMPLIED BY OPERATION OF LAW. OTHER THAN THE
EXPRESS LIMITED WARRANTY SET FORTH ABOVE,
THERE ARE NO OTHER WARRANTIES THAT
ACCOMPANY THIS PRODUCT AND ANY ORAL,
WRITTEN OR ANY OTHER EXPRESS REPRESENTATION
OF ANY KIND IS HEREBY DISCLAIMED.
• www.evenflo.com
• USA: 1-800-233-5921 8 AM – 5 PM E.T.
• Canada: 1-937-773-3971
• México: 01-800-706-12-00
52
• www.evenflo.com
• USA: 1-800-233-5921 8 AM – 5 PM E.T.
• Canada: 1-937-773-3971
• México: 01-800-706-12-00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising