A93 Actuators (Belimo) - Davies Supply Group Ltd.

A93 Actuators (Belimo) - Davies Supply Group Ltd.
21/02/14
A93
Actuators (Belimo)
Actuator - Spring Return - 35 in-lb Minimum Torque












Direct coupled spring return damper actuator
<60 second spring return
Overload Protection: Electronic throughout rotation
Angle of Rotation: 95o adjustable (electronically variable 0-100%)
Fits shaft diameter 3/8"-1/2" (standard) 1/2"-3/4" (with K6-1 clamp
accessory)
Visual position indicator
Direction of Rotation: CW/CCW external switch
Spring return is reversible through CW/CCW mounting
Dimensions: 7.67" x 3.15" x 3.23"
Electrical Connection: 3ft, 18GA plenum cable, 1/2" conduit fitting.
(appliance cable used on #LF120-SUS)
Housing: NEMA 2
5 year warranty
Control Input
Feedback
Power Supply
Running Time
VA Rating
Brand
Part Number
2 to 10 VDC
(4-20mA with 500ohm resistor, ZG-R01)
2 to 10 VDC
24 VAC/DC
150 seconds
constant
5
Belimo
LF24-SRUS
2 to 10 VDC, Built-in minimum position
2 to 10 VDC
24 VAC/DC
150 seconds
constant
5
Belimo
LF24-SR-EUS
On/Off
-
24 VAC/DC
40 to 75 seconds
7
Belimo
LF24US
On/Off
-
120 VAC
40 to 75 seconds
7.5
Belimo
LF120US
On/Off
-
120 VAC
40 to 75 seconds
7.5
Belimo
*LF120-SUS
* Built-in auxiliary switch: 1 SPDT, 3A (0.5A inductive) @ 250V
Actuator - Spring Return - 133 in-lb Minimum Torque













Direct coupled spring return damper actuator
<20 second spring return
Overload Protection: Electronic throughout rotation
Angle of Rotation: 95o adjustable (electronically variable 0-100%)
Fits shaft diameter 1/2"-1.05" (clamp self-centers on 1/2", 3/4" & 1.05")
Visual position indicator
Manual override with 3mm crank supplied
Direction of Rotation: CW/CCW external switch
Spring return is reversible through CW/CCW mounting
Dimensions: 10.59" x 3.86" x 3.10"
Electrical Connection: 3ft, 18GA appliance cable, 1/2" conduit fitting
Housing: NEMA 2 (IP54)
5 year warranty
Control Input
Feedback
Power Supply
Running Time
VA Rating
Brand
Part Number
2 to 10 VDC
(4-20mA with 500ohm resistor, ZG-R01)
2-10 VDC
24 VAC/VDC
150 seconds
10
Belimo
AFB24-SRUS
On/Off
-
24 VAC/VDC
150 seconds
10
Belimo
AF24US
On/Off
-
120 VAC
150 seconds
10
Belimo
AF120US
On/Off
-
24-120 VAC
24-125 VDC
75 seconds
10
Belimo
AFBUP
Davies Supply Group Ltd.
Calgary (800) 661-1346
(403) 244-2161
Lethbridge (877) 595-7707
(403) 381-7707
Saskatoon (877) 355-3377
(306) 933-2433
A94
23/07/10
Actuator Parts & Accessories (Belimo)
Crank Arm & Adapter Kit
Description
Brand
Part Number
Crank arm fits shafts up to 3/4 on AF & NF Belimo
Actuators
Belimo
KH-AFUS
Positions crank arm in same relative position as crank
arm on electric foot mount-type linkage actuators.
Includes retrofit bracket, ZG112 right angle bracket
and KH-LF crank arm
Belimo
ZG-LF112
Description
Brand
Part Number
Universal channel mounting bracket
(1 1/2" H x 5 1/2" W x 2 1/4" Base)
Belimo
ZG106
KH-AFUS
ZG-LF112
Mounting Bracket
ZG106
Davies Supply Group Ltd.
Calgary (800) 661-1346
(403) 244-2161
Lethbridge (877) 595-7707
(403) 381-7707
Saskatoon (877) 355-3377
(306) 933-2433
21/02/14
A94-1
Actuators (Honeywell)
Actuators - Spring Return - Universal Fire & Smoke Actuators











Spring return damper actuators for fire/smoke control applications
Reversible design enables mounting clockwise or counter clockwise spring return with one model
Patent pending design eliminates need for limit switches to reduce power consumption
Die-cast aluminum housing, housing design allows flush mounting to damper
Optional internal end switches reduce the installation time and eliminates the need for an accessory auxiliary switch pack
Clip-in conduit connections have been added to the base of the actuator to simplify wiring and connection of flexible conduit
Simplified , Self-centering shaft adapter (SCSA), enables fast, tight and secure connection to the damper
Damper shaft is stronger than in previous models, only requires two set screws for all models
Models available with SPST position-indicating switches (7°, 85° stroke)
Note : Designed to operate reliably in smoke control systems requiring
Underwriter’s Laboratories Inc. UL555S ratings up to 350 F (176°C), the
actuator must be tested with the damper to achieve this rating
No special cycling required during long-term holding
MS4104F
Description
two-position, 120 VAC
two-position, 2 SPSTa, 120 VAC
two-position, 120 VAC
two-position, 2 SPST, 120 VAC
two-position, 230 VAC
two-position, 2 SPSTa, 230 VAC
two-position, 230 VAC
two-position, 2 SPSTa, 230 VAC
two-position, 24 VAC
two-position, 2 SPSTa, 24 VAC
two-position, 24 VAC
two-position, 2 SPSTa, 24 VAC
two-position, 120 VAC
two-position, 2 SPSTa, 120 VAC
two-position, 230 VAC
two-position, 2 SPSTa, 230 VAC
two-position, 24 VAC
two-position, 2 SPSTa, 24 VAC
Davies Supply Group Ltd.
Torque
30 lb-in
3.4 N•m)
30 lb-in
(3.4 N•m)
80 lb-in
(9 N•m)
80 lb-in
(9 N•m)
30 lb-in
(3.4 N•m)
30 lb-in
(3.4 N•m)
80 lb-in
(9 N•m)
80 lb-in
(9 N•m)
30 lb-in
(3.4 N•m)
30 lb-in
(3.4 N•m)
80 lb-in
(9 N•m)
80 lb-in
(9 N•m)
175 lb-in
(20 N•m)
175 lb-in
(20 N•m)
175 lb-in
(20 N•m)
175 lb-in
(20 N•m)
175 lb-in
(20 N•m)
175 lb-in
(20 N•m)
Timing
15 sec
15 sec
15 sec
15 sec
15 sec
15 sec
15 sec
15 sec
15 sec
15 sec
15 sec
15 sec
15 sec
15 sec
15 sec
15 sec
15 sec
15 sec
Stroke
95° angle of
rotation
95° angle of
rotation
95° angle of
rotation
95° angle of
rotation
95° angle of
rotation
95° angle of
rotation
95° angle of
rotation
95° angle of
rotation
95° angle of
rotation
95° angle of
rotation
95° angle of
rotation
95° angle of
rotation
95° angle of
rotation
95° angle of
rotation
95° angle of
rotation
95° angle of
rotation
95° angle of
rotation
95° angle of
rotation
Calgary (800) 661-1346
(403) 244-2161
Power Consumption
0.18A, 18W (Driving)
0.11A, 9W (Holding)
0.25A, 23W (Driving) 0.13A,
7W (Holding)
0.13A, 18W (Driving)
0.10A, 11W (Holding)
0.13A, 23W (Driving)
0.09A, 7W (Holding)
16 VA (Driving)
8 VA (Holding)
23 VA (Driving)
7 VA (Holding)
0.35A, 35W (Driving)
0.15A, 10W (Holding)
0.20A, 35W (Driving)
0.14A, 10W (Holding)
45 VA (Driving)
10 VA (Holding)
Lethbridge (877) 595-7707
(403) 381-7707
MS4120F
Brand
Part Number
Honeywell
MS4104F1010
Honeywell
MS4104F1210
Honeywell
MS4109F1010
Honeywell
MS4109F1210
Honeywell
MS4604F1010
Honeywell
MS4604F1210
Honeywell
MS4609F1010
Honeywell
MS4609F1210
Honeywell
MS8104F1010
Honeywell
MS8104F1210
Honeywell
MS8109F1010
Honeywell
MS8109F1210
Honeywell
MS4120F1006
Honeywell
MS4120F1204
Honeywell
MS4620F1005
Honeywell
MS4620F1203
Honeywell
MS8120F1002
Honeywell
MS8120F1200
Saskatoon (877) 355-3377
(306) 933-2433
21/02/14
A95
Actuators (Honeywell)
Actuators - Spring Return





Zelix low torque direct coupled actuators are light and compact while delivering the power of larger models
Self-centering shaft adaptor attaches to the shaft with a single screw turn, no need for U-bolts
Mode Selector, Adapts models to floating (tri-state), modulating (proportional) or economizer applications
Wiring access cover allows direct wiring without a junction box
Standard wiring for all Honeywell actuators
SW2-US
Torque
Voltage
27 lb-in
(3 Nm)
24 VAC/DC
MS7505
Description
D2 Damper
7 in-lb per sq. ft.
D3 Damper
4.5 in-lb per sq. ft.
4 sq. ft.
6 sq. ft.
Floating and Modulating
24 VAC/DC
44 lb-in
(5 Nm)
120/230 VAC
24 VAC/DC
24 VAC/DC
88 lb-in
(10 Nm)
100-250 VAC
24 VAC/DC
24 VAC/DC
175 lb-in
(20 Nm)
100-250 VAC
MS7503A2030
Floating with Auxiliary Switches
MS7503A2130
Floating, Modulating and Economizer
MS7403A2030
Two Position
MS8105A1030
Two Position with Auxiliary Switch
MS8105A1130
Two Position
MS4105A1030
Two Position with Auxiliary Switch
6 sq. ft.
10 sq. ft.
MS4105A1130
Floating and Modulating
MS7505A2030
Floating and Modulating with Auxiliary Switch
MS7505A2130
Floating, Modulating and Economizer
MS7405A2030
Two Position
MS8110A1008
Two Position with Auxiliary Switches
MS8110A1206
Two Position
MS4110A1002
Two Position with Auxiliary Switches
13 sq. ft.
20 sq. ft.
MS4110A1200
Floating and Modulating
MS7510A2008
Floating and Modulating with Auxiliary Switches
MS7510A2206
Floating and Modulating with Auxiliary Switches & Adj. Zero
& Span
MS7510H2209
Two Position
MS8120A1007
Two Position with Auxiliary Switches
MS8120A1205
Two Position
MS4120A1001
Two Position with Auxiliary Switches
25 sq. ft.
39 sq. ft.
Floating and Modulating
24 VAC/DC
Part
Number
MS4120A1209
MS7520A2007
Floating and Modulating with Auxiliary Switches
MS7520A2205
Floating and Modulating with Auxiliary Switches & Adj. Zero & Span
MS7520H2208
Actuator Accessories (Honeywell) - Auxiliary Switch Pack
Description
SW 2 Auxiliary Switch Pack, Spring Return (MS) and High
Torque Non Spring
(NOTE! Not for use with Fire and Smoke Actuators )
Davies Supply Group Ltd.
Calgary (800) 661-1346
(403) 244-2161
Brand
Part Number
Honeywell
SW2-US
Lethbridge (877) 595-7707
(403) 381-7707
Saskatoon (877) 355-3377
(306) 933-2433
23/07/10
A96
Actuators (Honeywell)
Actuators - Non-Spring Return





Zelix low torque direct coupled actuators are light and compact while delivering the power of larger models
Self-centering shaft adaptor attaches to the shaft with a single screw turn, no need for U-bolts
Standard wiring for all Honeywell actuators
Mode Selector: Adapts models to floating (tri-state), modulating (proportional) or economizer applications
Wiring access cover allows direct wiring without a junction box
Torque
Voltage
35 lb-in
(4 Nm)
24 VAC
70 lb-in
(8 Nm)
24 VAC
Description
Two Position & Floating
Modulating
Two Position & Floating
Modulating
D2 Damper
7 in-lb per sq. ft.
D3 Damper
4.5 in-lb per sq. ft.
5 sq. ft.
8 sq. ft.
10 sq. ft.
16 sq. ft.
Two Position & Floating
44 lb-in
(5 Nm)
88 lb-in
(10 Nm)
24 VAC/DC
24 VAC/DC
24 VAC
175 lb-in
(20 Nm)
24 VAC/DC
300 lb-in
(20 Nm)
24 VAC
24 VAC/DC
Part
Number
ML6161B2024
ML7161A2008
ML6174B2019
ML7174A2001
MN6105A1011
Two Position & Floating with Auxiliary Switches
6 sq. ft.
Floating and Modulating
10 sq. ft.
MN6105A1201
MN7505A2001
Floating and Modulating with Auxiliary Switches
MN7505A2209
Two Position & Floating
MN6110A1003
Two Position & Floating with Auxiliary Switches
13 sq. ft.
Floating and Modulating
20 sq. ft.
MN6110A1201
MN7510A2001
Floating and Modulating with Auxiliary Switches
MN7510A2209
Two Position & Floating
MN6120A1002
Two Position & Floating with Auxiliary Switches
25 sq. ft.
Modulating
39 sq. ft.
Modulating with Auxiliary Switches
MN6120A1200
MN7220A2007
MN7220A2205
Two Position & Floating
43 sq. ft.
Modulating
67 sq. ft.
MN6134A1003
MN7234A2008
MN6110
ML6161
Davies Supply Group Ltd.
ML6174
Calgary (800) 661-1346
(403) 244-2161
Lethbridge (877) 595-7707
(403) 381-7707
Saskatoon (877) 355-3377
(306) 933-2433
09/05/14
A97
Economizer Actuators & Accessories (Honeywell)
Economizer Damper Actuators - Spring Return







24 VAC modulating spring return foot mounted damper actuators provide modulating control of economizer systems,
ventilation dampers and combustion air dampers
Synchronous motor
Spring returns motor shaft to normal position on power interruption
Uses Q298B linkage
Single ended drive shaft with 4074EGR crank arm assembly
90 Degree Fixed angle of rotation
Reinforced glass-fiber plastic case
Description
Used With
Rotation
Spring Return, foot mounted,
Spdt floating, 24 Vac
Floating
Controllers
Spring Return, foot mounted,
Modulating, 24 Vac
Power Consumption
Control Signal
Brand
Part Number
3 VA
Floating,
SPDT
Honeywell
M6415A1016
8 VA
3 VA
2 to 10 Vdc
Honeywell
M7215A1008
CCW
8 VA
5 VA
Thermistor,
Modulating
Honeywell
M7415A1006
W7459, W7460
Economizers
CW
8 VA
5 VA
Thermistor,
Modulating
Honeywell
M7415B1004
Spring Return, foot mounted,
3 position w/field adj. min pos., 24 Vac
W7459C
CCW
8 VA
3 VA
Three Position
Honeywell
M8405A1006
Spring Return, foot mounted,
2 position w/field adj. min pos., 24 Vac
-
CCW
8 VA
3 VA
Two Psition,
SPST
Honeywell
M8415A1004
Driving
Holding
CCW
8 VA
W7212/13/14,
W7215
Economizers
CCW
Spring Return, foot mounted,
Modulating, 24 Vac
W7459, W7460
Economizers
Spring Return, foot mounted,
Modulating, 24 Vac
Davies Supply Group Ltd.
Calgary (800) 661-1346
(403) 244-2161
Lethbridge (877) 595-7707
(403) 381-7707
Saskatoon (877) 355-3377
(306) 933-2433
25/10/13
A97-1
Economizer Actuators & Accessories (Honeywell)
JADE™ Economizer Logic Module (Series 72)




When used with the Demand Control Ventilation (DCV)
Sensor: This sensor varies the ventilation damper's minimum
ventilation position between two adjustable values (one for
low or highly variable occupancy and one for full
occupancy) to reduce outside air during low occupancy
periods
Description



Contact Ratings
Series 72
JADE™ Economizer
1.5A Run @ 30 Vac
Logic Module with
3.5A Inrush @ 30 Vac
Demand Control Ventilation
The JADE™ Economizer Module is an expandable economizer control
system. It can be configured for 4 different economizer strategies:
Referential or differential dry bulb, referential or differential enthalpy. It
can be used as a stand alone module or wired directly to a commercial set
back space thermostat and sensors to provide Outdoor Air dry-bulb
economizer control. The module can also be connected to optional Sylk
Bus sensors for single or differential enthalpy control, providing power
and communications.
Used with C7232 Demand Control Ventilation (DCV) CO2 Sensors,
C7400S1000 Enthalpy Sensor, C7250A Dry Bulb Temperature & Mixed
Air Sensors, and C7600 Humidity Sensors to proportion outdoor and
return air dampers for control of free cooling in commercial buildings
Used with Series 72 Actuators
Operates from commercial thermostat and DCV sensor to provide a
totally integrated control system
Automatically detects sensors by polling to determine which sensors are
present
Digital with LCD screen for programming and fault detection and
diagnostics
Energizes one or two supplemental exhaust fans during operation,
complete with exhaust cycle setpoint(s)
Input
C7250A Dry Bulb Temp &
Mixed Air Sensor
C7400S1000 Enthalpy Sensor
C7232 CO2 Sensor (For DCV)
C7600 Humidity Only
Output
Used With
Brand
Part Number
2-10 Vdc
to
actuator
Series 72
Actuators.
C7250A,
C7400S1000,
C7232, C7600
Sensors.
Honeywell
W7220A1000
Enthalpy Sensor


Digital enthalpy (temperature/humidity) sensor for use W7220
economizer module and S-Bus devices
Solid state sensor designed to sense temperature and humidity with
5% accuracy
Sensor
Mounting
Used With
Brand
Part Number
7-21 Vdc
Any position where it is exposed to freely circulating air
W7220 JADE™ Module
Honeywell
C7400S1000
Temperature Sensor

Mixed air sensor designed for use as a 20k input to a controller for
sensing mixed or discharged air in rooftop packaged conditioning
equipment
Sensor
Mounting
Used With
Brand
Part Number
20K NTC
Any position where it is exposed to freely circulating air
W7220 JADE™ Module
Honeywell
C7250A1001
Davies Supply Group Ltd.
Calgary (800) 661-1346
(403) 244-2161
Lethbridge (877) 595-7707
(403) 381-7707
Saskatoon (877) 355-3377
(306) 933-2433
17/01/14
A97-2
Economizer Actuators & Accessories (Honeywell)
Economizer Logic Module (Series 72)










Description
Series 72
Economizer Logic Module
with
Demand Control Ventilation
Used with C7232 Demand Control Ventilation (DCV) Sensors and
solid state C7400A Enthalpy Sensors or C7660 Dry Bulb Temperature Sensors to proportion outdoor and return air dampers for control
of free cooling in commercial HVAC equipment
Operates from commercial thermostat and DCV sensor to provide a
totally integrated control system
Mounts on M7215 Motor or ductwork
Used with Series 72 Actuators
Combines minimum and DCV maximum damper position potentiometers with compressor staging
Functions with solid state enthalpy or dry bulb changeover control
Terminals included for connecting optional S963B1128 Remote Potentiometer for remote minimum damper position control
LED indicates when free cooling is available, when module is in DCV
mode and when exhaust fan contact is closed
Features adjustable exhaust fan setpoint and indoor sensor input
Default minimum position in freeze protection
Contact Ratings
Input
Output
C7660 Dry Bulb Temp Sensor
2-10 Vdc
1.5A Run @ 24 Vac
C7400A Enthalpy Sensor
to
3.5A Inrush @ 24 Vac C7150 Mixed Air Temp Sensor
actuator
C7232 CO2 Sensor (For DCV)
Used With
Brand
Part Number
Series 72
Actuators.
C7150, C7400A,
C7232, C7660
Sensors.
Honeywell
W7212A1009
Enthalpy Sensor




Solid state enthalpy sensor used with Honeywell economizer logic
modules to proportion outdoor and return air dampers in economizer
systems
Solid state element sense enthalpy (temperature and humidity); use
two sensors for differential control, maximizing energy savings
Use one sensor in outdoor air for single sensor control; use two
sensors, one in return and one in outdoor air, for differential control
Mount in any position up to 200 feet away from W7459
Application Type
Mounting
Used With
Brand
Part Number
Duct outside (supply) or return
Any position where it is
exposed to freely circulating air
W7210, W7212, W7213, W7214, W7215, W7459,
W7460
Honeywell
C7400A1004
Temperature (Dry Bulb) Sensor



Selectable temperature sensor used with economizer controls that are
mounted on a M7415/M7215 Actuator senses temperature of outdoor
air and provides a signal to economizer control with OK or not OK to
economize. Only to be used with single temperature change over with
the sensor located in the outdoor air.
Permits the use of outdoor air as the first stage of cooling in heating,
ventilating and AC (HVAC) systems
Selectable dip switch provides 8 change over temperature options
Application Type
Mounting
Used With
Brand
Part Number
Duct outside (supply) or return
air with 4 or 20mA output signal
Any position where it is
exposed to freely circulating air
W7210, W7212, W7213, W7214, W7215, W7459,
W7460 Economizer Controls
Honeywell
C7660A1000
Davies Supply Group Ltd.
Calgary (800) 661-1346
(403) 244-2161
Lethbridge (877) 595-7707
(403) 381-7707
Saskatoon (877) 355-3377
(306) 933-2433
23/07/10
A98
Damper Actuators (Honeywell)
Damper Actuator - Two Position - Spring Return










Spring return motors for two position back draft, outdoor air changeover, zone or minimum position damper control
Operate outdoor air dampers for combustion or makeup air in residential and light commercial applications
Operate changeover dampers for heating and cooling systems
Operate minimum position dampers for ventilation and similar
applications
Includes internal SPDT switch for controlling auxiliary equipment,
additional motors, or to provide a burner interlock switch
Spring returns motor to start position on power failure
Drive shafts located on both sides of motor
Adjustable auxiliary switch for cascading motors or operating
auxiliary equipment
Thermal breaker for overload protection during lifting stroke or if
motor fails
Features 2 hexagonal shafts and is foot mounted
Volts
Torque
Rating
Run Time
(Max)
Opening
Timing
Stroke
Description
Brand
Part
Number
120 Vac
20 lb-in.
(2.3 Nm)
40 sec
30 sec
75o
Two position, SPST control signal.
One internal auxiliary switch.
Honeywell
M436A1116
24 Vac
15 lb-in.
(1.7 Nm)
40 sec
25 sec
75o
Two position, SPST control signal.
One internal auxiliary switch.
Honeywell
M836B1033
Draft Damper Actuator - Two Position - Spring Return





Two position draft damper actuators used with two-wire 24V room
thermostats or other low voltage controllers to operate the draft
damper on solid fuel furnaces or boilers and other similar light duty
applications
Equipped with mounting bracket for wall, duct or direct appliance
mounting to control draft damper through an actuator arm or chain
linkage arrangement
Actuator wheel rotates in a clockwise direction (when facing the
wheel) when energized
Features 1 round shaft and is foot mounted, direct coupled
Includes 3.8" linkage arm
Volts
Torque
Rating
Run Time
(Max)
Stroke
Description
Brand
Part
Number
24 Vac
1.9 lb-in.
(0.21 Nm)
20 sec
45o
Two position, SPST control signal.
Bracket mounted with change linkage.
Honeywell
M847A1031
24 Vac
1.9 lb-in.
(0.21 Nm)
20 sec
45o
Two position, SPST control signal.
Bracket mounted with change linkage and
extended bracket.
Honeywell
M847A1098
Davies Supply Group Ltd.
Calgary (800) 661-1346
(403) 244-2161
Lethbridge (877) 595-7707
(403) 381-7707
Saskatoon (877) 355-3377
(306) 933-2433
23/07/10
A99
Modutrol IV™ Actuators (Honeywell)
Modutrol IV™ Actuator - Two Position - Spring Return






Volts
Torque
24/120/230 Vac
60 lb-in.
(6.8 Nm)
120 Vac
60 lb-in.
(6.8 Nm)
Timing
Used to operate dampers and valves in applications where it is necessary or
desirable to have the controlled element return to the starting position in the
event of a power failure or interruption
Can operate valve linkages from the power end or auxiliary end shafts for
normally closed or normally open valve applications
Features dual ended shafts and is foot mounted
Shaft Rotation (upon control signal increase): Clockwise, as viewed from
power end, normally closed
Includes transformer
Integral junction box provides NEMA 3 weather protection if mounted in the
upright position
Stroke
Description
Brand
Part Number
30 sec to 60 sec
90o to 160o
Two position, SPST control signal.
One internal auxiliary switch.
Honeywell
M4185E4006
30 sec to 60 sec
90o to 160o
Two position, SPST control signal.
One internal auxiliary switch.
Honeywell
M4185E4014
Modutrol IV™ Actuator - Floating - Non-Spring Return






Non-spring return floating control motors are used with controllers that provide a switched SPDT or floating output to operate dampers or valves
Designed for either normally open or normally closed valves and dampers
Internal electrically isolated feedback potentiometer that provides indication of
the motor shaft position
Features dual ended shafts, auxiliary switch cams and is foot mounted
Shaft Rotation (upon control signal increase): Dependent on wiring, normally
closed
Integral junction box provides NEMA 3 weather protection if mounted in the
upright position
Volts
Torque
Timing
Stroke
Description
Brand
Part Number
24 Vac
150 lb-in.
(17 Nm)
30 sec to 60 sec
90o to 160o
Floating control signal. Non-linear feedback,
for slaving applications only
Honeywell
M6284D4004S
Modutrol IV™ Actuator - Modulating - Non-Spring Return






Volts
120 Vac
Torque
150 lb-in.
(17Nm)
Davies Supply Group Ltd.
Timing
30 sec to 60 sec
Non-spring return motors used to control dampers and valves. They accept a
current or voltage signal from an electronic controller to position a damper or
valve at any point between open and closed.
Designed for either normally open or normally closed valves and dampers
Features dual ended shafts, auxiliary switch cams and is foot mounted
Shaft Rotation (upon control signal increase): Clockwise, as viewed from
power end, normally closed
Includes transformer and screw terminal adapter
Integral junction box provides NEMA 3 weather protection if mounted in the
upright position
Stroke
Description
Brand
Part Number
90o to 160o
4-20 mA modulating control signal and
adjustable zero and span for split range
applications. Two internal auxiliary
switches
Honeywell
M7284Q1009
Calgary (800) 661-1346
(403) 244-2161
Lethbridge (877) 595-7707
(403) 381-7707
Saskatoon (877) 355-3377
(306) 933-2433
23/07/10
A100
Modutrol IV™ Actuators (Honeywell)
Modutrol IV™ Actuator - Proportional - Non-Spring Return

Non-spring return modulating proportional control motors used with
controllers that provide a Series 90 output to operate dampers or
valves
Features dual ended shafts, auxiliary switch cams and is foot mounted
Shaft Rotation (upon control signal increase): Counter Clockwise
(1009) and Clockwise (1021, 4006), as viewed from power end, normally closed
Integral junction box provides NEMA 3 weather protection if
mounted in the upright position



Volts
Torque
24 Vac
60 lb-in.
(4 Nm)
24 Vac
24 Vac
Timing
Stroke
Description
Brand
Part Number
30 sec to 60 sec
o
90 to 160
Proportional, 135 ohm control signal
Honeywell
M9164D1009
150 lb-in.
(17 Nm)
30 sec to 60 sec
90o to 160o
Proportional, 135 ohm control signal
Honeywell
M9184D1021
150 lb-in.
(17 Nm)
30 sec to 60 sec
90o to 160o
Proportional, 135 ohm control signal.
One internal auxiliary switch.
Honeywell
M9184E4006
o
Modutrol IV™ Actuator - Proportional - Spring Return

Spring return modulating proportional control motors used with controllers that provide a Series 90 output to operate dampers or valves
Operates valve linkages from power end or normally open valve applications
Features dual ended shafts, auxiliary switch cams and is foot mounted
Shaft Rotation (upon control signal increase): Clockwise, as viewed
from power end, normally closed
Integral junction box provides NEMA 3 weather protection if
mounted in the upright position




Volts
Torque
24 Vac
60 lb-in.
(6.8 Nm)
24 Vac
60 lb-in.
(6.8 Nm)
Timing
Stroke
Description
Brand
Part Number
30 sec to 60 sec
o
90 to 160
Proportional, 135 ohm control signal
Honeywell
M9185D4008
30 sec to 60 sec
90o to 160o
Proportional, 135 ohm control signal.
One internal auxiliary switch.
Honeywell
M9185E4005
o
Modutrol IV™ Actuator - Proportional - For Flame Safeguard

Reversing, proportional motors used to drive burner firing rate valves,
dampers or auxiliary equipment
Designed for flame safeguard applications in commercial/industrial
oil or bas burner system
Replaces M9141A,C,D motors
Vibration resistant electronic drive circuit
Regulated by three-wire proportional controller
Double ended shaft, 3/8"





Volts
Torque
24 Vac
150 lb-in.
(17 Nm)
30 sec to 60 sec
24 Vac
150 lb-in.
(17 Nm)
30 sec to 60 sec
Davies Supply Group Ltd.
Timing
Stroke
Description
Brand
Part Number
90 to 160
Proportional control signal for 135 ohm firing
rate applications
Honeywell
M9484D4006
90o to 160o
Proportional control signal for 135 ohm firing
rate applications. One internal auxiliary switch.
Honeywell
M9484E4003
o
o
Calgary (800) 661-1346
(403) 244-2161
Lethbridge (877) 595-7707
(403) 381-7707
Saskatoon (877) 355-3377
(306) 933-2433
23/07/10
A101
Actuator Parts & Accessories (Honeywell)
Auxiliary Switch (For Modutrol III™ & Modutrol IV™)








For control of auxiliary equipment as a function of motor shaft
position
Compatible with Modutrol III™ and Modutrol IV™ actuators.
(Requires 220738A adapter bracket for use with Modutrol IV™)
Adjustable Micro Switch precision switches
Indicate motor position by use of scale plate anchored to a common
shaft, which allows Q607 to be adjusted for operation sequence before
mounting
Adjustable plate allows universal mounting on either end of motor
Wrap-around cover for easy access to switch adjustments and wiring
Maintenance free protection of the switches and cams
Includes adapter for cover end spring return motor and revised mounting bracket
Description
Brand
Part Number
SPDT, On/Off switch control signal. One internal auxiliary
switch. Used on Post 1969 Honeywell Modutrol Actuators.
Honeywell
Q607A1076
Adapter Bracket (For Modutrol III™ & Modutrol IV™)

Adapter bracket adjusts shaft height to match Modutrol III actuator
Description
Brand
Part Number
Used with Modutrol IV™ to match shaft height of
Modutrol III™ Actuator
Honeywell
220738A
Description
Brand
Part Number
Infinitely adjustable crank arm for Modutrol IV™ motors
Honeywell
221455A
1/2" diameter damper shaft crank arm for all actuators and
dampers
Honeywell
26026G
Description
Brand
Part Number
Fits 5/16" diameter pushrods. 1/4" - 28 UNF Male Threads.
Used with all actuators and dampers.
Honeywell
27518
Crank Arms
Crank Arm Ball Joint
Davies Supply Group Ltd.
Calgary (800) 661-1346
(403) 244-2161
Lethbridge (877) 595-7707
(403) 381-7707
Saskatoon (877) 355-3377
(306) 933-2433
23/07/10
A102
Actuator Parts & Accessories (Honeywell)
Crank Arm Assemblies
Description
Brand
Part Number
Auxiliary crank arm assembly for M835, Q298.
SPST, On/Off switch control signal.
Honeywell
121825AA
Crank arm assembly with clip for damper arm of V4066,
V4062 or V9055
Honeywell
7616BR
121825AA
7616BR
Linkage Assembly

Connects motor to 1 or 2 zone dampers with 1/4" to 1/2" diameter
shafts.
Description
Brand
Part Number
Includes 2 damper arms, 2 ball joints and 24" push rod.
Linkage for M6415, M7405, M7415, M8405, M8415 and
dampers.
Honeywell
Q298B1065
Linkage Assembly (For Modutrol IV™)


Davies Supply Group Ltd.
Connects Modutrol IV actuators to standard damper or set of dampers
to provide control of duct airflow
Adjustable to any degree of damper opening.
Description
Brand
Part Number
Includes motor mounting bracket, 3 damper arms, 3.1"
motor crank arm, 4 ball joints, left hand drive ear and crank
arm adapter
Honeywell
Q605H1024
Calgary (800) 661-1346
(403) 244-2161
Lethbridge (877) 595-7707
(403) 381-7707
Saskatoon (877) 355-3377
(306) 933-2433
23/07/10
A103
Actuator Parts & Accessories (Honeywell)
Linkage Bag Assembly (For M836)

Linkage bag assembly for M836 actuators
Description
Brand
Part Number
Consists of: 1 adapter shaft, 1 lever, 2 clamps, 1 coupling, 4 screws, 1 set screw and washer
Honeywell
7640JP
Valve Linkages (For Modutrol™)





Connect Modutrol actuator to a 2 or 3 way valve in modulating or two
-position service
Used primarily on V5011 or V5013 steam water valves
Requires no adjustment when used with Honeywell valves and
Modutrol IV actuators
Mounts directly to the valve bonnet; motor mounts to linkage bracket
Easy to read position indicator
Stem Force
Lift Adjustment
Bonnet Size
Description
Brand
Part Number
80 lb., 160 lb.
3/4" fixed
1 3/8"
Replaces linkage Q601J,K,L.M, and Q618A.
Has anti-spin feature.
Honeywell
Q5001D1000
Description
Brand
Part Number
Angle mounting bracket for M436 & M836 actuators to
side of duct
Honeywell
7640JM
Mounting Bracket (For M436, M836)
Davies Supply Group Ltd.
Calgary (800) 661-1346
(403) 244-2161
Lethbridge (877) 595-7707
(403) 381-7707
Saskatoon (877) 355-3377
(306) 933-2433
23/07/10
A104
Actuator Parts & Accessories (Honeywell)
Internal Auxiliary Switch Assemblies (For Modutrol IV™)




220736A
Control auxiliary equipment as a function of motor shaft position
For installation in any Modutrol IV actuators
Cams can be set to actuate switches at any angle within stroke of
motor
Selectable switch differentials of one or ten degrees of rotation
Volts
Description
Brand
Part Number
120/240
Includes one Micro Switch V3 precision switch,
which is actuated by adjustable cams inside the
motor
Honeywell
220736A
120/240
Includes two Micro Switch V3 precision
switches, which are actuated by adjustable cams
inside the motor
Honeywell
220736B
220736B
Transformers (For Modutrol IV™ Series 1 & 2 Actuators)


Single or multi-tap to match 24 VAC power supply
Includes transformer, screws and instructions for mounting
Volts
Description
Brand
Part Number
120/208/
240 Vac
Multi-tap transformer mounts internally in
Modutrol IV Series 1 Actuators
Honeywell
198162AA
120 Vac
Transformer mounts internally in Modutrol IV
Series 1 Actuators
Honeywell
198162EA
24/120/
230 Vac
Transformer mounts internally in Modutrol IV
Series 2 Actuators
Honeywell
50017460-001
198162AA
Davies Supply Group Ltd.
Calgary (800) 661-1346
(403) 244-2161
Lethbridge (877) 595-7707
(403) 381-7707
Saskatoon (877) 355-3377
(306) 933-2433
23/07/10
A105
Actuator Parts & Accessories (Honeywell)
Manual Potentiometers (For Modutrol™)




Used to limit minimum position of a proportioning Modutrol actuator
Mounts directly into motor
All wiring is accomplished within motor wiring compartment
Color-coded lead wires
Resistance
Dimensions
Description
Brand
Part Number
150 ohms
1" High x 1 3/10" Wide x 2 3/10" Deep
(25mm High x 33mm Wide X 59mm Deep)
For M744, M745, M941, M945, M954, M955
Modutrol actuators with screw terminals.
Includes leadwires and mounting brackets
Honeywell
Q209A1022
150 ohms
3 1/4" High x 3 3/8" Wide x 3 7/8" Deep
(83mm x 86mm x 98mm)
External mount onto Modutrol IV actuators.
Includes quick-connect terminals with leadwires
Honeywell
Q209E1002
Resistor Board (For Modutrol IV™)



Mounts inside wiring box of an M91XX Modutrol IV actuator, can be
used in place of 4074BUY, 4074EAU, 4074EDC or 4074EED resistor
kits
Board snaps on easily to any M91XX Modutrol IV actuator
Board can be configured for any application listed by setting dip
switch:
- In 4074BYK application, board allows single series 90
controller to operate up to six motors in unison
- In 4047EDC, EED application, board permits operation of one
to four motors from 4-20 mA controller
- In 4074EAU application, board allows W973 Single-one Logic
panel to drive two or three motors
Description
Brand
Part Number
Resistor board used with Modutrol IV actuator. One board can be configured for any above application listed.
Honeywell
221508A
Davies Supply Group Ltd.
Calgary (800) 661-1346
(403) 244-2161
Lethbridge (877) 595-7707
(403) 381-7707
Saskatoon (877) 355-3377
(306) 933-2433
23/07/10
A106
Actuator Parts & Accessories (Honeywell)
Interface Modules (For Modutrol IV™)





For converting series 90 Modutrol IV actuator to series 70 (electronic) control
Mounts inside wiring box of any series 90 Modutrol IV actuator
Mates to motor's quick-connect terminals and provides screw terminals for control wiring connections
Features solid-state circuitry with surface mount components
Plastic enclosure provides easy handling and protection for circuitry
Q7330A1004
Q7130A1006, Q7230A1005
Q7630A1001
Description
Brand
Part Number
Provides selectable voltage ranges: 4 to 7, 6 to 9, or 10.5 to 13.5 Vdc. Adapts M91xx to function as M71xx model
Honeywell
Q7130A1006
Provides adjustable zero & span, voltage or current control (includes 2-10 Vdc or 4-20mA). Adapts M91xx to
function as M72xx model
Honeywell
Q7230A1005
Provides interface to W936 Control. Adapts M91xx to function as M73x model
Honeywell
Q7330A1004
Provides 3-wire 14 to 17 Vdc control with a minimum position capability. Adapts M91xx to function as M76xx
model
Honeywell
Q7630A1001
Davies Supply Group Ltd.
Calgary (800) 661-1346
(403) 244-2161
Lethbridge (877) 595-7707
(403) 381-7707
Saskatoon (877) 355-3377
(306) 933-2433
17/01/14
A107
Actuators (Johnson)
Actuator - Electric Motor


Used to position dampers, valves and related equipment in heating,
ventilation, air conditioning and industrial applications
Possess single sized housing for all torques, linkage connection flexibility to either end of the output shaft, solid-state drive and travel limits, and die-cast aluminum housing with corrosive resistant cover
M130AAB-1
M150AGA-1
Torque
Breakaway
Torque
Volts
Auxiliary
Switch
Adjustable
Travel (Stroke)
Timing
50 in.-lb
200
120
1 - SPDT
45o to 270o
60 seconds/160o
150 in.-lb
300
24
o
None
o
45 to 270
o
60 seconds/160
Description
Brand
Part Number
Spring Return
Johnson
M130AAB-1
Non-Spring Return
Johnson
M150AGA-1
Actuator - Positioner




Davies Supply Group Ltd.
Use where control for up to three additional actuators with a single
positioner is desired
Use for 2 stage operation
Precision relay devices that adjust and maintain pneumatic damper
actuators in exact positions
Provides dynamic stabilization and/or sequential control
Calgary (800) 661-1346
(403) 244-2161
Description
Brand
Part Number
Used with D3153-1 two stage actuator
Johnson
D-9502-9
Lethbridge (877) 595-7707
(403) 381-7707
Saskatoon (877) 355-3377
(306) 933-2433
08/07/11
A108
Actuator Parts & Accessories
This Page Left
Intentionally
Blank
Davies Supply Group Ltd.
Calgary (800) 661-1346
(403) 244-2161
Lethbridge (877) 595-7707
(403) 381-7707
Saskatoon (877) 355-3377
(306) 933-2433
23/07/10
A109
Actuators
This Page Left
Intentionally
Blank
Davies Supply Group Ltd.
Calgary (800) 661-1346
(403) 244-2161
Lethbridge (877) 595-7707
(403) 381-7707
Saskatoon (877) 355-3377
(306) 933-2433
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement