917Vw User Manualx

Add to my manuals
29 Pages

advertisement

917Vw User Manualx | Manualzz

917Vw User Manual

1. Preface

About This Guide

This guide describes the monitor's features, setup, and operation. lnformation in this document is subject to change without notice.

The sections are as follows:

Safety Instructions

Setup

: lists safety information.

: describes the initial setup process.

Using the Monitor

Drivers

: gives an overview of how to use the monitor.

: provides driver installation instructions for Windows.

Technical Support : provides tips and solutions for common problems.

Product Information : lists the technical specifications of the monitor.

National Conventions

The following subsections describe notational conventions used in this document.

Notes, Cautions, and Warnings

Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These blocks are notes, cautions, and warnings, and they are used as follows:

NOTE:

A NOTE indicates important information that helps you make better use of your computer system.

CAUTION:

A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

WARNING:

A WARNING indicates the potential for bodily harm and tells you how to avoid the problem.

Some warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific presentation of the warning is mandated by regulatory authority.

Product Registration

Please link www.aoc.com

, select your country or region, log in Product Registration to register.

2. Safety Introduction

FCC Notice

FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS)

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.

2. Increase the separation between the equipment and receiver.

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

4. Consult the dealer or an experienced radio/TV technician for help.

NOTICE :

1. The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

2. Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits.

3. The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. It is theresponsibilities of the user to correct such interference.

WEEE Declaration

Disposal of Waste Equipment by Users in Private Household in the European Union.

This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste.Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or the shop where you purchased the product .

HG Declaration

SAFETY: Lamp Disposal

LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR

FEDERAL LAWS. FOR MORE INFORMATION, CONTACT THE ELECTRONIC INDUSTRIES ALLIANCE AT

WWW.EIAE.ORG

.

Precautions

WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards, and/or mechanical hazards.

Read and follow these precautions when connecting and using your computer monitor:

PRECAUTIONS

Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement.

Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance. Use only a cart or stand recommended by the manufacturer or sold with the monitor. If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit instructions.

Slots and openings in the back and bottom of the cabinet are provided for ventilation. To ensure reliable operation of the monitor and to protect it from overheating, be sure these openings are not blocked or covered. Do not place the monitor on a bed, sofa, rug, or similar surface. Do not place the monitor near or over a radiator or heat register. Do not place the monitor in a bookcase or cabinet unless proper ventilation is provided.

The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the type of power supplied to your home, consult your dealer or local power company.

The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of the grounded plug.

Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the monitor from damage due to power surges.

Do not overload power strips and extension cords. Overloading can result in fire or electric shock.

Never push any object into the slot on the monitor cabinet. It could short circuit parts causing a fire or electric shock. Never spill liquids on the monitor.

Do not attempt to service the monitor yourself; opening or removing covers can expose you to dangerous voltages and other hazards. Please refer all servicing to qualified service personnel.

To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate configured receptacles marked between

100 - 240V AC, Min. 5A.

The wall socket shall be installed near the equipment and shall be easily accessible.

For use only with the attached power adapter (Output 12Vdc) which have UL,CSA listed license(Only for monitors with power adapter).

Please make sure to clean the cabinet regularly with the provided cloth , you can use soft-cleanser to clean the stain , instead of severe spray

• cleanser which will cauterize the monitor cabinet.

Dont leak liquid into monitor which will result in the damage of chassis or component. Please unplug before cleaning ,and do not scratch the screen with hard things.

3. Setup

Setup the stand and base

Please setup or remove the base following below steps.

Adjusting Viewing Angle

For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference.

Hold the stand so you do not topple the monitor when you change the monitor's angle.

You are able to adjust the monitor's angle from -5°to 20°.

NOTE:

Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.

Attaching the Cables

Cable Connections On Back of Monitor and Computer

1. Power

2. DVI

3. Analog

Turn off your computer before performing the procedure below.

1. Connect the power cable to the AC port on the back of the monitor.

2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port.

3. Turn on your monitor and computer.

If your monitor displays an image, installation is complete. If it does not display an image, see Troubleshooting .

Attaching Wall Mounting Arm

Preparing to Install An Optional Wall Mounting Arm

This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this procedure. Follow these steps:

1. Remove the base.

2. Follow the manufacturer's instructions to assemble the wall mounting arm.

3. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor.

4. Insert the 4 screws into the holes and tighten.

5. Reconnect the cables. Refer to the user's manual that came with the optional wall mounting arm for instructions on attaching it to the wall.

4. Using the Monitor

Setting the Optimal Resolution

The recommended resolution for this monitor is 1440 by 900. To setup the monitor to this resolution, follow the steps below.

1. Click START.

2. Click SETTINGS.

3. Click CONTROL PANEL.

4. Double click DISPLAY.

5. Click SETTINGS.

6. Set the resolution SLIDE-BAR to 1440 by 900.

External Controls

Press the power button to turn the monitor on or off. The other control knobs are located at front panel of the monitor (See Figure ). By changing these settings, the picture can be adjusted to your personal preferences.

* The power cord should be connected.

* Press the power button to turn on the monitor. The power indicator will light up.

1 Eco Mode / Up

2 Exit / Left

3 Menu / Right

4 Auto / Down

5 Power on/off

OSD Settings

1) Press the MENU-button ( ) to activate the OSD window.

2) Press or to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate sub-menu . Once the desired function is highlighted, press MENU-button to activate it.

3) Press or to change the settings of the selected function. Press or to select another function in sub-menu . Press

AUTO( ) to exit . If you want to adjust any other function, repeat steps 2-3.

4) OSD Lock Function: To lock the OSD, press and hold the MENU button while the monitor is off and then press power button to turn the monitor on. To un-lock the OSD - press and hold the MENU button while the monitor is off and then press power button to turn the monitor on.

5) Eco Mode hot key ( ) : Press the Eco key continuously to select the Eco mode of brightness when there is no OSD ( Eco mode hot key may not be available in all models).

6) Volume adjustment hot key : When there is no OSD , press Volume ( ) to active volume adjustment bar, press or to adjust volume ( Only for the models with speakers).

DCB Adjustment

What is DCB?

Dynamic Color Boost (DCB) is an advanced color adjustment technology. Through analyzing RGB signals, DCB creates more vivid and natural images to suit various color environment needs. DCB has two types of color enhancers: “Color Boost” and “Picture

Boost” .

DCC: Dynamic color control

ICM: Intelligent color management

1) How to use Color Boost?

YCM adjustment: In addition to the basic R (red), G (green), B (blue) color adjustments, Color Boost has added Y (yellow), C

(cyanine), and M (magenta) for more color fine-tuning options. YCM adjustments are in the third icon labeled "Color Temperature "in the OSD menu. When adjusting YCM values, RGB values will also be changed automatically due to the color correlation between

RGB and YCM.

Five color-enhancement settings: To accommodate various display needs, Color Boost also offers 5 different color enhancement modes: Full Enhance, Natural Skin, Green Field, Sky Blue, and Auto-Detect. Please go to the fourth icon labeled “Color Boost” in the

OSD menu and select one of the five settings you desire to be turned on.

Full Enhance: When "Full Enhance" is turned on, the color saturation of the entire screen is fully enriched, thus all colors become

more vibrant.

Nature Skin: When "Natural Skin" is turned on, the red and yellow colors are enriched automatically, thus presents human skin with more natural and truer colors. "Natural Skin" setting is ideal for viewing human portrait and detailed skin texture.

Green Field: When "Green Field" is turned on, the green color is enriched so that football field and mountain landscape would look more natural and fresh. “Green Field” setting is ideal for watching mountain scenery and outdoor sports.

Sky Blue: When"Sky Blue" is turned on, the color blue is being fine-tuned so that the sky or ocean landscape will look more vivid and in-depth. "Sky Blue" setting is ideal for viewing sky and ocean images.

Auto Detect: When “Auto Detect” is turned on, every pigment will be detected and self-adjusted to render a lively picture.

Demo: Screen divided into two for demonstration purposes.

2) How to use Picture Boost?

Users can change the color settings of a self-selected zone on the screen. The size and position of the selected zone can also be adjusted. "Picture Boost" is located in the fifth icon labeled "Picture Boost" in the OSD menu. Turn on "Bright Frame" to select a zone on the screen to be enhanced. Please note when adjust or turn on any one of the DCB features, the rest of color settings including

DCR will be disabled or return to default.

Disclaimer: DCB aftereffects are subject to the resolution and quality of the display content, hence may look different than the above

illustrations.

DCR Adjustment

What is DCR?

Dynamic Contrast Ratio (DCR) auto adjusts the brightness of the screen so users can see the darker areas of the displayed content in more depths. By increasing the darkness of the dark areas and the brightness of the bright areas, contrast ratio is uplifted to exceed 2000:1. DCR value varies subject to the original CR values of the LCD module. The higher the original CR, the higher DCR can be achieved. DCR is great for watching movie or video contents.

How to Use DCR?

Go to the first OSD icon labeled "Luminance", turn on or off DCR as desires. DCR boosts the contrasts between lightness & darkness and enables the viewer to see more layers and details of the picture, especially in the darker areas. Please note when DCR is on,

DCB will be disabled.

DCR Demos:

Disclaimer: DCR aftereffects are subject to the resolution and quality of the display content, hence may look different than the above

illustrations.

Function Control Illustration

Luminance

Brightness

Contrast

Eco mode

Gamma

DCR

Adjust Range

0-100

0-100

Standard

Text

Internet

Game

Movie

Sports

Gamma1

Gamma2

Gamma3

Off

Description

Backlight Adjustment

Contrast from Digital-register.

Standard Mode

Text Mode

Internet Mode

Game Mode

Movie Mode

Sports Mode

Adjust to Gamma1

Adjust to Gamma 2

Adjust to Gamma 3

Disable dynamic contrast ratio

On mage Setup

Clock

Focus

H.Position

V.Position

Color Temp.

Warm

Normal

Cool sRGB

User

Color Boost

Full Enhance

Nature Skin

Green Field

Sky-blue

AutoDetect

Demo

Picture Boost

Frame Size

Brightness

Contrast

Hue

Saturation

Position

0-100

0-100

0-100

0-100

User-B

User-G

User-R

User-Y

User-C

User-M on or off on or off on or off on or off on or off on or off

0-100

0-100

0-100

0-100

0-100

H. position

Enable dynamic contrast ratio

Adjust picture Clock to reduce Vertical-Line noise.

Adjust Picture Phase to reduce Horizontal-Line noise

Adjust the verticalposition of the picture.

Adjust the horizontal position of the picture.

Recall Warm Color Temperature from EEPROM.

Recall Normal Color Temperature from EEPROM.

Recall Cool Color Temperature from EEPROM.

Recall SRGB Color Temperature from EEPROM.

Blue Gain from Digital-register

Green Gain Digital-register.

Red Gain from Digital-register

Yellow Gain from Digital-register

Cyan Gain from Digital-register

Magenta Gain from Digital-register

Disable or Enable Full Enhance Mode

Disable or Enable Nature Skin Mode

Disable or Enable Green Field Mode

Disable or Enable Sky-blue Mode

Disable or Enable AutoDetect Mode

Disable or Enable Demo

Adjust Frame Size

Adjust Frame Brightness

Adjust Frame Contrast

Adjust Frame Hue

Adjust Frame Saturation

Adjust Frame horizontal Position

LED Indicators

Status

Full Power Mode

Active-off Mode

Bright Frame

OSD Setup

H.Position

V.Position

Timeout

Language

Extra

Input Select

Auto Config

Reset

DDC-CI

Information

V.position on or off

0-100

0-100

0-100

Digital

Analog yes or no yes or no

LED Color

Green or Blue

Orange or red

Adjust Frame vertical Position

Disable or Enable Bright Frame

Adjust the verticalposition of OSD

Adjust the horizontal position of OSD

Adjust the OSD Timeout

Select the OSD language

Select Digital Sigal Source as Input

Select Analog Sigal Source as Input

Auto adjust the picture to default

Reset the menu to default

Turn ON/OFF DDC-CI Support

Show the information of the main image and sub-image source

5. Drivers

Windows 2000

1. Start Windows® 2000

2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.

3. Double click on the 'Display' Icon.

4. Select the 'Settings' tab then click on 'Advanced...'.

5. Select 'Monitor'

- If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation.

- If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps given below.

6. Click on 'Driver' and then click on 'Update Driver...' then click on the 'Next' button.

7. Select 'Display a list of the known drivers for this device so that I can choose a specific driver', then click on 'Next' and then click on 'Have disk...'.

8. Click on the 'Browse...' button then select the appropriate drive F: ( CD-ROM Drive).

9. Click on the 'Open' button, then click on the 'OK' button.

10. Select your monitor model and click on the 'Next' button.

11. Click on the 'Finish' button then the 'Close' button.

If you can see the 'Digital Signature Not Found' window, click on the 'Yes' button.

Windows ME

1. Start Windows® Me

2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'.

3. Double click on the 'Display' Icon.

4. Select the 'Settings' tab then click on 'Advanced...'.

5. Select the 'Monitor' button, then click on 'Change...' button.

6. Select 'Specify the location of the driver(Advanced)' and click on the 'Next' button.

7. Select 'Display a list of all the drivers in a specific location, so you can choose the driver you want', then click on 'Next' and then click on 'Have Disk...'.

8. Click on the 'Browse...' button, select the appropriate drive F: ( CD-ROM Drive) then click on the 'OK' button.

9. Click on the 'OK' button, select your monitor model and click on the 'Next' button.

10. Click on 'Finish' button then the 'Close' button.

Windows XP

1. Start Windows® XP

2. Click on the 'Start' button and then click on 'Control Panel'.

3. Select and click on the category 'Printers and Other Hardware'

4. Click on the 'Display' Item.

5. Select the 'Settings' tab then click on the 'Advanced' button.

6. Select 'Monitor' tab

- If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation.

- If the 'Properties' button is active, click on 'Properties' button.

Please follow the steps below.

7. Click on the 'Driver' tab and then click on 'Update Driver...' button.

8. Select the 'Install from a list or specific location [advanced]' radio button and then click on the 'Next' button.

9. Select the 'Don't Search. I will choose the driver to install' radio button. Then click on the 'Next' button.

10. Click on the 'Have disk...' button, then click on the 'Browse...' button and then select the appropriate drive F: (CD-ROM

Drive).

11. Click on the 'Open' button, then click the 'OK' button.

12. Select your monitor model and click on the 'Next' button.

- If you can see the 'has not passed Windows® Logo testing to verify its compatibility with Windows® XP' message, please click on the 'Continue Anyway' button.

13. Click on the 'Finish' button then the 'Close' button.

14. Click on the 'OK' button and then the 'OK' button again to close the Display_Properties dialog box.

Windows Vista

1. Start Windows® Vista

2. Click the Start button; select and click on 'Control Panel'.

3. Select and click on 'Hardware and Sound'

4. Choose 'Device Manager' and Click on 'Update device drivers'.

5. Select 'Monitor' and then right click on 'Generic PnP Monitor'.

6. Click on 'Update Driver Software'.

7. Select 'Browse my computer for driver software'.

8. Click the 'Browse'button and choose the drive in which you've placed the disk. Example:(CD-ROM Drive:\\Lcd\PC\drivers\).

9. Click the 'Next' button.

10. Wait few minutes for installing the driver, and then click 'Close' button.

6. Technical Support

Frequently Asked Questions

Problem & Question

Power LED Is Not ON

No Plug & Play

Picture Is Fuzzy & Has Ghosting

Shadowing Problem

Picture Bounces, Flickers Or

Wave Pattern Is Present In The

Picture

Monitor Is Stuck In Active

Off-Mode"

Possible Solutions

Make sure the power button is ON and the Power Cord is properly connected to a grounded power outlet and to the monitor.

In order for the Plug & Play feature of the monitor to work, you need a Plug & Play compatible computer & video card. Check with your computer manufacturer. Also check the monitor's video cable and make sure none of the pins are bent.

Make sure the AOC Monitor Drivers are installed (AOC Monitor Drivers are available at : http://www.aoc.com

)

Adjust the Contrast and Brightness Controls.

Make sure you are not using an extension cable or switch box. We recommend plugging the monitor directly to the video card output connector on the back of your computer.

Move electrical devices that may cause electrical interference as far away from the monitor as possible.

Use the maximum refresh rate your monitor is capable of at the resolution your are using.

The Computer Power Switch should be in the ON position.

The Computer Video Card should be snugly seated in its slot.

Make sure the monitor's video cable is properly connected to the computer.

Inspect the monitor's video cable and make sure none of the pins are bent.

Missing one of the primary colors

(RED, GREEN, or BLUE)

Screen image is not centered or

sized properly

Picture has color defects (white

does not look white)

Horizontal or vertical disturbances

on the screen

Make sure your computer is operational by hitting the CAPS LOCK key on the keyboard while observing the CAPS LOCK LED. The LED should either turn ON or

OFF after hitting the CAPS LOCK key.

Inspect the monitor's video cable and make sure that none of the pins arebent.

Make sure the monitor's video cable is properly connected to the computer.

Adjust H-Position and V-Position or press hot-key (AUTO).

Adjust RGB color or select color temperature

Use win 95/98 shut-down mode Adjust CLOCK and FOCUS or perform hot-key

(AUTO-key )

7. Product Information

Specifications

LCD Panel Model number

Driving system

Viewable Image Size

Pixel pitch

Video

Separate Sync.

Display Color

917Vw

TFT Color LCD

481mm diagoanl

0.2835mm(H) x 0.2835mm(V)

R, G, B Analog lnterface & Digital Interface

H/V TTL

16.7M Colors

Dot Clock 135 MHz

Resolution Horizontal scan range 30 kHz - 83 kHz

408.24mm Horizontal scan

Size(Maximum)

Vertical scan range 56 Hz - 75 Hz

Vertical scan 255.15mm

Size(Maximum)

Optimal preset resolution

Highest preset resolution

Plug & Play

Input Connector

Input Video Signal

Power Source

Power Consumption

1440 x 900 (60 Hz)

1440 x 900 (60 Hz)

VESA DDC2B/CI

D-Sub 15pin & DVI-D

Analog: 0.7Vp-p(standard), 75 OHM, Positive & DVI-D Digital Interface

(TMDS)

100~240VAC, 47~63Hz

Active < 37W

Standby < 2W

Physical

Characteristics

Connector Type

Signal Cable Type

15-pin Mini D-Sub & DVI-D

Detachable

Dimensions & Weight:

Height (with base) 439 mm

Width

Depth

358 mm

204 mm

Weight (monitor only) 3.8 kg

Weight (with packaging) 4.7 kg

Environmental Temperature:

Operating 0° to 50°

Non-Operating

Humidity:

Operating

-20°to 60°

10% to 85% (non-condensing)

Non-Operating

Altitude:

Operating

Non-Operating

5% to 80% (non-condensing)

0~ 3000m (0~ 10000 ft )

0~ 5000m (0~ 15000 ft )

EPA ENERGY STAR ®

ENERGY STAR® is a U.S. registered mark. As an ENERGY STAR® Partner, AOC International (Europe) GmbH has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.

Preset Display Modes

STAND RESOLUTION

Dos-mode

VGA

SVGA

XGA

SXGA

WXGA

720 × 400

640 × 480

640 × 480

800 × 600

800 × 600

1024 × 768

1024 × 768

1024 × 768

1280 × 1024

1280 × 1024

1440 × 900

HORIZONTAL

FREQUENCY(kHZ)

31.47kHz

31.47kHz

37.50kHz

37.879kHz

46.875kHz

48.363kHz

56.476kHz

60.021kHz

64.000kHz

80.000kHz

55.935kHz

VERTICAL

FREQUENCY(Hz)

70.0Hz

60.0Hz

75.0Hz

60.0Hz

75.0Hz

60.0Hz

70.0Hz

75.0Hz

60.0Hz

75.0Hz

59.8Hz

Pin Assignments

Pin Number

9

10

11

12

13

14

15

1

6

7

8

2

3

4

5

15-Pin Side of the Signal Cable

Video-Red

Video-Green

Video-Blue

N.C.

Ground

GND-R

GND-G

GND-B

+5V

Detect Cable

N.C.

DDC-Serial data

H-sync

V-sync

DDC-Serial clock

Pin No.

1

2

3

4

5

6

7

8

Signal Name

TMDS Data 2-

TMDS Data 2+

TMDS Data 2/4 Shield

TMDS Data 4-

TMDS Data 4+

DDC Clock

DDC Data

N.C.

Plug and Play

Pin No.

9

10

11

12

13

14

15

16

Signal Name

TMDS Data 1-

TMDS Data 1+

TMDS Data 1/3 Shield

TMDS Data 3-

TMDS Data 3+

+5V Power

Ground(for+5V)

Hot Plug Detect

Pin No.

17

18

19

20

21

22

23

24

Signal Name

TMDS Data 0-

TMDS Data 0+

TMDS Data 0/5 Shield

TMDS Data 5-

TMDS Data 5+

TMDS Clock Shield

TMDS Clock +

TMDS Clock -

Plug & Play DDC2B Feature

This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.

The DDC2B is a bi-directional data channel based on the I

2

C protocol. The host can request EDID information over the DDC2B channel.

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement