quiet comfort - Sears Parts Direct

quiet comfort - Sears Parts Direct
H •.....••
Save this manual
for future
reference
SEAR8
owner's
manuat
Stock No.
42-14415
Model No.
758.144150
®
QUIET COMFORT
WHOLE HOUSE
HUMiDiFiER
13 Gallon Output
FOR YOUR
SAFETY:
innovative Twin Fan
Technology
READ
ALL INSTRUCTIONS
CAREFULLY
......
J
• Operating instructions
- Parts List
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Part No, SP6354
Printed in Canada
FULL
ONE YEAR
WARRANTY
ON HUMIDIFIER
(1) year fr0m the date of purchase, this humidifier fails due to a defect in
material Or workmanshiP, Sears will repair it, free of charge. If within two (2) years from
the date of purchase, the motor fails due to defect in material or workmanship, Sears
i
r service
ts available
by simply returning
the humidifier to the nearest Sears
,iwhile this product is used in the United States
...... .........
!_a! tights, and you may also have other rights which
Vary'from state to state._:_:,_:
....
:;
Seam; Rbebuck and Co., D/817 WA, Hoffman Estates, IL 60179
GENERAL SAFETY iNSTRUCTiONS
Safety Signal Words
DANGER:
means
4,
if the safety
is not fo!lowed, someone
injured or killed.
information
will be seriously
6.
WARNING;
means if the safety
is notl followed, someone could
ly injured or killed.
information
be serious-
CAUTION:
means if the safety information
is not followed,
someone may be seriously
injured or killed.
I.
To reduce the risk of fire or _
hazard,
plug humidifier directly into a 120V, A.C. electrical outlet. Do not use extension cords.
2,
Keep the electric
cord out of traffic areas.
To reduce the risk of fire hazard, never put
the electric cord under rugs, near heat
registers, radiators,
Keep the humidifier
5. Do not put
humidifier.
Never
clean.
foreign
use your
objects
humidifier
inside
while
the
any part
is missing or damaged
in any manner.
7. To reduce the risk of electrical hazard or
damage to humidifier,
do not tiff, jolt or
tip humidifier
while
unit is running.
8. To reduce the risk of damage
fier, unptug humidifier,
when
tles are empty
not in use.
9. To
reduce the
or when
to humidiwater bot-
the humidifier
risk of accidental
electri-
caJ shock, do not touch the cord
trols with wet hands.
10.Note
the warning
label shown
or con-
below.
stoves or heaters.
3. Always
unplug
the humidifier
before
moving it, before cleaning,
or whenever
the humidifier
is not in service.
1
WARNING:
To reduce
tric shock,
or injury
before filling, servicing
risk
of fire, elec-
always
unplug
or cleaning.
Table of Contents
Warranty Information ....... ;..........................
Generat Safety Instructions ........................
To Save A Service Catt ...............................
2
2
2
Know Your Humidifier .................................
3
HUmidifier Operations
................................
4
Assembly ....................................................
4
Location Instructions
...............................
4-5
Electrical
Hook-Up .......................................
5
Water Flit..................................................
5-6
Operating Humidifier Controls ................... 7
Manual Dryout .....................................
i....... 7
Using Your Humidifier .................................
8
Operating -13ps for Best Performance ......... 8
Replacement and Care of Filters ........... 9-t0
Cleaning Your Humidifier ..................... 11-12
Troubleshooting
.......................................
13
Repair Parts .........................................
14-15
To Save a Service Call
Check
the following
ff your humidifier
not operate,
I _ IS power cord attached
2. ts there electricaf
to outlet?
power to outlet?
witl
is
3. is airflow
control
in operating
position?
4. ts humidity control set high enough?
5. ts the cabinet sitting on a level surface?
|
1
Know "Your Humidifi'er ............................
............................
Control Panel Cover & Pivoting Lid Removed for Clarity
Desired
Humidity
Fan Assembly
Controls
Fitter
Housing
Filters:
Replacement
Filter
42-14415
Description
Gaiton
OutpuV24
Hrs.
Capacity of Bottles
Sq. Ft. Coverage
Fan Speeds
Filters
FillLight
Desired Humidity Light
Automatic
Humidistat
Controis
CU L Listed
AHAM Certified
Volts
Hertz
Arnps
Watts
2-3/8
13
Gallons
2700
3
Each
4
Yes
Yes
Yes
Rotary
Yes
Yes
120 A.C.
60
2,88
165
* Based on an area with average insulation and
an 8 foot ceiling height.
Humidifier Operations
i
Your: new Sears humidifier is designed to
SatiSfyi::home : humidity _requirements
through the principle of evaporation of
water in the air.
After water is added to the bottle, the filters begin to soak up the water and
become totally saturated in approximately
30 minutes. Air is drawn in from the rear of
the humidifier and through the filters by
means of circulation fans. As air passes
through the filters, moisture is absorbed
into the air and then released in the form
of vapor, No water droplets will enter the
home. All evaporation into the air takes
place in the humidifier, which means that
the residue left by evaporating water is not
passed into the home, but remains in the
filter.
=
/
Humidified Air is
Then Released
Through the Top
Dry Air Enters
Rear
Through the
_]
CAUTION: To reduce the risk of injury,
fire or damage to humidifier, use only
cleaners specifically
recommended
for humidifiers. Never use flammable,
combustible or poisonous materials to
clean your humidifier, To reduce the
risk of scalds and damage to humidifier, never put hot water in humidifier.
only
Registered
Bacteriostat
available
from SEARS Retail store, Under no
circumstances should you use water
ICAUTION:
Use
42-14900
EPA
treatment products
designed
for Rote
belt or Ultrasonic humidifiers.
Assembly .........................
Your new Sears Kenmore humidifier is completely assembled for you to use. Remove
the packaging material from •inside your
humidifierand follow the instructionsof this
Location
Instructions
I WARNING: For your own safety, do not !
use humidifier tfany parts are damaged |
| or missing
,
owneds manual for proper usage. The
packaging material is located under the fan
assembly. Remove the packaging material
and discard.
.............
,,,,
!
Step i
Place humidifier on a fia_level surface in an
area Of house where most humidity is need.:ed, or one which would likely result in moist
air being circulated throughout the house,
such as near acold air return. •
Placing the unit ievel is very important ff the
humidifieris located on carpeting.
NOTE: The t3 gallon humidifier contains
•water bottles. The weight of the bottles in
the frontof the cabinet may cause the front
casters to sink deeper into the carpet. If this
happens, the water level wilt be higher
towards the front of the humid_er, and
lower towards the back. The water level
float (located:at the rea_of the cabinet) may
not sense _ water so the fill light will be on
and the unit will not energize; fithis happens, the unit will need tO be leveled in
order for the humidifierto be energized, tt
may be necessary to purchase leveling
coasters from your local hardware store.
The coasters should be positioned under
the front two casters of the humidifier.
Location
NOTE:
from
instructions
DL_e to release
humid_er,
(continued)
of coo!, moist
air
it is best to direct air away
from home thermostat &r_d hot air registers.
It is best to position humid_er
next to an
inside wa!t. Hot air regis!ers and co3d air
from outside walls can affe_l the efficiencies
of the controls.
Unit should
...................
Step 2
The humidifier should be pos_ioned with the
back (cord exit side), at least 2 inches away
from the wall. Air needs to enter through the
_ouvres in the rear pane! in order for the
humidifier to operate at peak efficiency.
not be ptaced
where warm air from a hot air register blows
directly on unit,
Moist air (humid_/)
produced wilt disperse
into the whole house, but _ea closest to the
unit wilt have the highest humidity, ff the unit
is positioned close to a window, condensa*
lion may form on the window pa_e. tf this is
not appropriate
the unit should be repositioned in another location.
Electrical
Locate nearest
location
Hook-Up
.............................
12OV A.C. wall socket in the
desired,
preferably
Plug in the electrical
on inside wall
cord.
shock
hazard,
humidifier
should
be
plugged
intoToa reduce
12OV A.C.
WARNING:
the outlet.
risk of Do
fire not
or
use extension
cords,
Water Fill ......................
WARNING: To reduce the risk of shock,
always unplug humidifier
before cleaning or servicing.
WARNING:
To reduce
Pivoting lid Removed
for Clarity
-"
Fan
Assembly
/
_-_///Water
the risk of fire
shock hazard, do not pour or spill
into control or motor area. Closewattii
trios
control cover, if controls get wet,
them dry completely
and have unit
checked by an authorized
service
sonnet before plugging in.
per-
This humidifier is designed for use with the
two water bottles that are located under the
pivoting lid.
Open the pivoting
lid of the humidifier.
Remove the water bottles by lifting them
straight up and out of the cabinet.
Front of Humidifier
.
;
Water Fill (continued)
Notice the water bottles are designed as
right'and left:! hand units.: Position them in
_e _correct iocation ;so the humidifier:can
function properly. The waterbottles should
rest in the front of the cabinet. Each"E-ZFill Side:Cap" must be:facing the rear of
the unit.
Each water bottle is designed: with an "EZ-Fill Side-Cap" that is easily removable.
Remove the "E-Z-Fill Side-Cap" on the
side of the water bottle by twisting counterclockwise.
"E-Z-Fill Side-Cap"
Should Always Face Rear
Place the opening of the water bottle under
a water faucet [the bottle should fit under a
four-inch clearance faucet). Fill with recommended mixture of cold water and
Sears Bacteriostat #42-14900 (if necessary) only, Solid debris could make the
valve leak.
....
Turn Counterclockwise
ove Cap
Install the "E-Z-Fill Side-Cap" by twisting
clockwise, Hand tighten only.
Check for possible leaks by performing
the following:
1. Grasp bottle handle and hold the bottle
uPright over a sink_
2. Press up on valve Cap plunger for about
one second to let out a little water.
3. Release the plunger.
4. Listen foi_ air btibbles. Look for leaks
around the "E-Z-Fill Side-Cap".
Valve
Cap Plunger
5. If you hear air bubbles or see leaks,
retighten the "E-Z-Fil! Side-Cap" and
: : i_epeat Steps_i_4!:i: ;
: Wipel off excess W_te_ from the bottle.
Posit_on the Water. botUe back into the unit
; by
graspir_ the water bottle handle and
0wer.ff into the cabinet until the bottlesits
" on padsat b0ttom ofcabinet. "rhe "E-Z-Fiil
-: iSide-Cap" must i0e facing the rear of the
:cabinet.
when:positioned
pr0perly, the
plunger
will 0pen:and Water will flow into
: the cab net The :water evei wilt automatically remain at approximately 1/2" until the
bottles areempty. _=i ....
The unit is now ready for operation.
Pivoting Lid
for Clarity
Removed
_
Operating Humidifier Controls
The operating controls of your Kenmore
Quiet Comfort whole house humidifier are
located on the top center of the humidifier.
The controls are found under the smoked
control cover, located between the air circulating fans,
Fill Light
When the humidifier is almost out of water,
the Fill light will come on and the fans will
automatically shut off.
0
Lift the control cover by placi,ng your finger
in the round cutout and lifting. The cover
will stay open. Now you can clearly see the
control area. Familiarize yourself w_th the
controls and reference the diagram of the
control area for the correct naming used in
this manual.
To Operate
Humidity
0
0=
'L!i)'
e
0
0
e_kx
the Controls
Control:
IMPORTANT: Water damage may result ff
condensation starts to form on windows or
wails. Humidity Control setting should be
lowered until condensation
no longer
forms.
Humidity
Light
When the selected humidity level is met,
the fans will shut off and the green
"Desired Humidity" _ight will illuminate,
When more humidity is called for, the fans
will turn on and the I_t
OFF
6_
Adjust the amount of humidity depending
on your needs. The humidifier will turn on
and off as required to maintain level of
humidity selected. A medium setting is recommended, but there are times when low
or high amount of humidity may be preferred. For constant operation of humidifier, MAX allo'ws for the maximum amount of
humidity to be evaporated into the air continuously.
Desired
....
,,,
will go out.
Speed Control
The unit is adjusted from "OFF" to "3" with
a rotary speed control. The higher the air
flow speed, the more water is evaporated
and released into the air. Low speed (1) is
the quietest and is provided for conditions
that may not require as high an evaporation rate.
FILL
Q
DESIRED
HUMIDITY
o, 13
Manual
Dryout
At the end of the humidification season or
if you do not plan to run the humidifier for
one week or mo.Te, you can override the
automatic shutoff function to completely
dry the humidifier cabinet out.
To do this, simply slide the float retainer
ideated at the back of the humidifier cabinet to the top position of the slot it is located in. This will hold the float in an upward
position and the fans will run until you turn
the power off.
NOTE: Be sure to position float retainer to
the normal operating mode (lowest position in slot) for humidifier operation.
Below is a diagram of the slot the float
retainer is located in at the back of the cabinet.
TOP POSITION iS FOR
MANUAL DRYOUT
<_____ BOTTOM POSITION IS FOR
NORMAL OPERATION MODE
L
::::4
: :
_:i:i
/
¸
:.
:•
•i
/!:,/
•=
•
•
Step 4
NOTE: Humidifier
should
....
operate
with
humidity control on the recommended
medium setting. If it does not, the humidity
is at a relatively high level. To test the unit
under this condition, turn Humidity Control
all the way to MAX and unit should begin
to operate, After the unit has been tested,
set Humidity Control to medium or desired
level.
Allow 24 hours for humidifier to adjust.
If humidity level in home is sufficient, the
humidifier will only operate with Humidity
Control set on MAX.
if humidifier stops running and the "Desired
Humidity"
indicator
is illuminated,
the
humidity level is at the normal requirements for that setting or it is adjusting to
the home conditions• The chart below
shows recommended indoor humidity levels.The figure below shows approximate
relative humidity percentages which correspond to the various settings of the
Humidity Control.
When Outdoor
Temperature is:
Recommended
indoor Relative
Humidity is:
-10°F
0°F
10°F
20°F & above
2O%
25%
30%
35%
IMPORTANT: Water damage may result if
condensation starts to form on windows or
walls. Humidity Control setting should be
lowered until condensation
no longer
forms.
Relative
Operating
Tips for Best Performance
1, Positionthe humidifier at least 2 inches
: _rom any wall and away from any heat
registers:
2; Do not restrict airflow from entering or
exiting the humidifier:
3. Use Sears rec0mmerided bacteriostat
42-14900 to retard bacteria growth that
may cause odors and may :be harmful
to your health..
Humidity
.....
4. Perform regular cleaning as instructed
in "Clean ng Your Hum differ" section of
this manual.
5. Replace the evaporative wicking fii_ers
at least once per humidification season
or more depending on water conditions
in your area.
Replacernent
and Care of Filters
WARNING: To reduce the risk of shock I
l
or injury from moving parts, always t
unplug humidifier before removing or t
replacing any parts,
t
CAUTiON:
To help retard bacteria l
growth and keep maximum efficiency, I
the filters should be replaced at least I
once per season, or more often under I
hard water conditions. Use Sears rec- I
ommended replacement filter 42-14911. I
Ail filters may be rinsed in clear water only.
Take care not to damage paper. To replace
evaporative wicking filters in your Kenmore
Quiet Comfort Whole House humidifier, follow the instructions below.
1. Unplug humidifier and proceed to clean.
Before removing the filters, we recommend moving the humidifier to an area
where floor coverings are not susceptible to water damage, i.e. kitchen or bath
areas.
Pivoting Lid
Fan Assembly
2. Open the pivoting lid and remove water
bottles and set aside. Grasp the fan
assembly front center and rear center.
Lift off and set aside on a clean flat surface. The filter housings are now accessible.
3. Lift filter housing out of cabinet and place
where you may work on them comfortably. With a soft, absorbent cloth remove
any remaining water or loose mineral
deposits not trapped in the fitter from the
humidifier cabinet.
4. To open filter housing for easy access to
filters:
a. Deflect the two spring tabs on top of
filter housing. Lift top cover off of the
filter housing and set aside.
b. Remove the two filters and dispose
of properly. Clean internal parts of
humidifier
per the "Cleaning of
Humidifier" section of your owner's
manual,
Cabinet
Front of Humidiifer
Spring
Tabs
Filter
Replacement
and Care of Filters (continued)
i
Install new filters in the filter housing
track with the glue beads of the wicking pad to the inside of the filter housing.
C.
d.
Fixed Tabs
Spring Tabs
Return the top cover of the filter
housing by installing the cover over
the fixed tabs on the rear of the lower
filter housing and pivoting the cover
down over the topof the filters. Snap
the cover over the two spring tabs.
Fiker
Replace the filter housing in the cabinet. Note: There is a left and a right
filter housing. There is also a front
and back orientation. To position the
filter housings correctly:
• Make sure the two indents in the
cylinder section of the top covers are
positioned towards the center of the
cabinet,
e,
Rear of
Humidifier
Front of
Humidifier
• Be sure that the spring tabs of filter
housings are towards front of cabinet.
\
• Align the lower portion of the filter
assembly over the six ribs located at
the bottom rear of the humidifier cabinet,
f.
Indents
Towards
Center of
Cabinet
Top
Cover
Position fan assembly onto the cabinet, Make sure the fan venturi (lowest cylinder section below the fan) is
placed inside the filter housing.
g. Replace water bottles.
h_' CloSe the pivoting lid.
Flat Portion of Filter Housing
Towards Back of Cabinet
::it :The Unit is ready for, use orl t° be
: :_ stored away for next seaso n.
NOTE:::: Foi _Oit_ ct: operation: of the fiter
housing assembly, fitters must be fully con:tair!ed insidet,e flange: of the toP cover,
i
:i:¸
=
:
•
Indents Toward Center of Cabinet
:: i-
Step 4 e.
10
:
Cleaning Your Humidifier
i
............:
......
Step 2
To Remove
CAUTION: Local water purity varies
from area to area and under certain
conditions water impurities and airborne bacteria
may promote the
growth of microorganisms
in the
reservoir of the humidifier.
the humidifier cabinet, we recommend
moving the humidifier to an area where
floor coverings are not susceptible to
water damage, i.e., kitchen or bath
area. Lift the filter housing assemblies
out of the cabinet and set to the side.
c. Remove the water level float from the
humidifier cabinet by pinching the float
retainer to release it from the cabinet.
The cabinet should be empty before
cleaning. The cabinet consists of the
lower areas of the humidifier where the
filters are during normal operation time.
Parts
a. Open the pivoting lid and remove water
bottles and set aside. Grasp the fan
assembly front center and rear center.
Lift off and set aside on a clean flat surface. The filter housings are now
accessible.
b. Before removing the internal parts of
To retard bacteria growth that may
cause odors and be harmful to your
health, use only Sears replacement
filters. We also recommend using
EPA approved bacteriostat, 42-14900
and humidifier
cleaner 42-14713,
available at your local Sears store.
d. Empty cabinet of any remaining water,
e. Proceed to "Bi-Weekly Maintenance"
or "End of Season Maintenance."
NOTE: If it is necessar¢ to use approved
bacteriostat, follow directions correctly.
The bottles of the whole house humidifier
will hold 2-3/8 gallons of water each.
Step 1
f.
Remove old filters and dispose of properly as described on page 9 and 10.
Step 3
To make cleaning easier, the humidifier
cabinet shoutd be empty and completely
dried out. To accomplish this, use the following method:
a. On the back side of the humidifier cabinet, find the float retainer. In normal
operating mode, the retainer wilt be
positioned in the bottom of the slot in
the cabinet. Push the retainer up to the
top slot position in the cabinet until it
locks in place. (See "Manual Dryout"
section on page 7.)
b. Allow the humidifier to run until there is
no water left in the cabinet.
Install new filters (purchase the correct
evaporative wicking filter pads 42-14911
for your humidifier) into the location where
the old filters were positioned. Install the
filter housings with the new filters into the
correct location. Reinstall the water level
float. NOTE: Float retainer should be positioned in normal operating mode. Assure
that it is positioned in the bottom of the slot
in the back of the cabinet. (See page 7 for
diagram of slot.) Position the fan assembly
on top of the cabinet and return the humidifier to the desired location for use.
Refill humidifier bottles with fresh cool water
and return them to the cabinet. Plug the unit
into a 120 volt A.C. power outlet and set the
controls per the "Operating Humidifier
Controls" section of this manual.
c. Unplug humidifier,
l
_lllji
WARNING:
To reduce the risk of
injury, fire or damage to humidifier,
,use only cleaners specifically recommended
for humidifiers.
Never
use flammable, combustible
or poisonous
materials
to clean your
humidifier.
To reduce the risk of
scalds
and damage to humidifier,
never put hot water in humidifier.
plugged, fan could start after housing
ARNING: If humidifier is not un- 1
is removed.
1t
Cleaning of Humidifier
B_:,Weekly
(continued) ....
Maintenance
......
=
End of Season
Removing Scale:
i. Fili:the i_umidffier cabinet with one 8
oz_ cupof undiluted white vinegar. Let
lution stay 20 minutes.
2. _Clean all interior surfaces with a soft
1
Fo low
"B-Weekly
MaintenanCe ;_'I
instructions at end of humidification:
season.
:i:
2. Remove and throw away fUteis. 'i ' :
3. Let humidifier dry completely before
storing. Do not store with water inside
cabinet or water bottles.
brush. Dampen a soft cloth with Undiluted white vinegar and wipe out the
cabinet to remove scale.
4. Store in coot, dry location.
:
5. Install a new filters in clean humidifier
before next season begins.
3: Rinse thoroughly with clean warm
water to remove scale and cleaning
solution before disinfecting cabinet.
6. "Bi*Weekly" is also recommended if
you do not plan to run the humidifier for
one week or more.
4. Dust the fan assembly and outside surfaces with a soft cloth only.
Disinfecting Humidifier Cabinet
and Water Bottles
1, Fill humidifier cabinet with 1 teaspoon
chlorine bleach in 1 gallon of water, Let
solution stay for 20 minutes, swishing
every few minutes. Wet all surfaces
normally exposed to water.
2. Empty humidifier cabinet after 20 minutes. Rinse with water until bleach
smelJ is gone. Allow unit to dry out
completely.
3. Water bottles should be cleaned in the
same manner.
12
Troubleshooting
"
'
.......
,'iTrouble ...............
:....................
Probable Cause= , ......
"
Remedy
Unit will not run and neither
control panel tight is
illuminated,
• No Power.
• Check 120 volt power
source.
Unit will not shut off.
- Float retainer is positioned
in "Manual DR/out" position.
- Slide float retainer down to
normal operation mode,
Refer to "Manual Dryout"
section on page 7.
• Float is not free,
- Free float from obstruction.
* Float is positioned in
normal operation mode.
• This is normal, A small
amount of water remains
in the cabinet after Fill
Light comes on. Position
float retainer in "Manual
Dryout" position to completely dry out. See page 7.
Bottles continue to empty.
• Air is entering water
bottles.
:- Check "E-Z-Fill Side-Caps"
and valve assembly caps
to ensure lightness,
• Check for leak in water
bottles.
, Ensure gaskets for "E-Z-Fill
Side Caps" are in place
(see repair parts list).
Unit is not emptying,
. Dirty fiiters
Unit will not dry out
completely,
................
i
....
"
• Bottle cap plunger missing
post in bottom of cabinet
Fill Light turns on before
bottles are empty.
•Cha getofreshnewfilters.(42-14911)
• Check orientation of bottle.
Reposition so that bottle
cap plunger is depressed by
post in bottom of cabinet.
• Position unit level. (Some
• Unit is not set up on a
carpet padding may allow
level surface, (Float will
not sense water at the rear unit to sit lower in front
than rear with the additionof the cabinet.)
al weight of water bottles
in the front of the cabinet,
Install coasters under front
casters,
,,,,,,,
CAUTION:'"_'se only 42-14_0
Retail store.
,,,,,,
,,,,,,,,,,,
E'PA Registered 'B'acteriostat
,, ,,,,,
,
av&ilable' from Sears
Use of other water treatment products may damage the filter elements.
Under no circumstances should you use water treatment products designed for
Roto belt or Ultrasonic humidifiers,
,...............
13
Repair Parts
_
_
Parts List for Sears Humidifiers
....
Model No. 758.144150
t
f
CO
C_
Repair Parts
......................................
Parts List for Sears Humidifiers
Model No. 758.144150
Always order by part number - Not by key number
X
_
X
E:
03
o
o3
3z
co
!.L
0 0
r- _j
03
>.-I
.--
o
J_
I-"o
_-___
OOr_o_O09
>
-_
g==.
_-_-_._
-o: _
LIJl_
o
o- I. '_
U-_OOg_LL
COOtr
g,o_
:3
o
_0
o
rn_
0
o
Eo
_-NmmmNm
mm
_o
r.3
_o
_z
Z
__o
>.
•
_ .__-__
_"
"_'_ _"
._"
_
>o'_
"o
0
t,o
r-
O
E
0
_o
_h__
CO L_ L_ "r
0
.,._,
O0 [U
_o_m__oo_
22
_0_
__
N
m
_z
15
Forthe repair or replacementpartsyou need
Call7 am- 7 pm, 7 days a week
1oS@O-366°PART
(1-800-388-7278)
For in-home majorbrand repair service
Call24 hours a day, 7 days a week
t-SGOo4-R_PAmR
(1-800-473-7247)
Forthe Bocationof a Sears RepairService
Center in your area
Call24 hours a day, 7 days a week
t -800-488-1222
For informationonpurchasinga Sears
MaintenanceAgreementor to inquire
aboutan existingAgreement
Call9 am - 5 pro, Monday-Saturday
t -800-827-6655
://
SEARS
,/
Amedea's
Repazr
Spectat,_t5
The model numberwill be foundon the Humidifier identification label.
When requestingservice or ordering parts, always providethe following information:
• ProductType
- Model Number
• Part Number
o Part Description
© 2000 Emerson Electric Co.
Sears, Roebuck and Co., Hoffman Estates,
Part.
No. SP6354
Form.
No. SP6354-1
IL 60179 U.S.A.
Printed
in Canada
09/00
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising