Kelvinator KRS220RHY1, KGM220RHY3 Owner's manual

Kelvinator KRS220RHY1, KGM220RHY3 Owner's manual
COMMERCIAL FR
R/REFRIGERATOR
GLASS DOOR REFRIGERATOR
TABLE OF CONTENTS
Product Registration ................................................
Important Safety Instructions ....................................
Electrical Information ...............................................
2
2
2-3
Caster Installation and Setup ........................................
Appliance Start-up .....................................................
Features .................................................................
Routine Maintenance ...............................................
3-4
4
5
6
Energy Conservation
Measures .................................
Troubleshooting
Guide .............................................
Wiring Diagram .......................................................
6
7-8
9
READ AND SAVE THESE INSTRUCTIONS
Electrolux Major Appliances
297279901 (March 2009)
Product
Registration
Proper Disposal
Risk
of Appliance
of Child
Entrapment
Child entrapment and suffocation are not problems of the
past. Junked or abandoned refrigerators or freezers are still
dangerous - even if they will sit for "just a few days". If you are
getting rid of your old refrigerator or freezer, please follow the
instructions below to help prevent accidents:
Read and Save These
Instructions
This Use & Care Guide provides specific operating instructions
for your model. Use your freezer only as instructed in this
guide. These instructions are not meant to cover every possible
condition and situation that may occur. Common sense and
caution must be practiced when installing, operating, and
maintaining any appliance.
e
Remove the door.
e
Leave shelves in place so
children may not easily
climb inside.
Record Your Model and Serial Numbers
Record the model and serial numbers in the space provided
below. The serial plates are located on the left exterior wall
(chest models).
Information
These guidelines must be followed to ensure that safety
mechanisms in the design of this appliance will operate
properly.
Model No.
Serial No.
Register Your Product
The self-addressed PRODUCT REGISTRATION CARD (shown
above) should be filled in completely, signed and returned to the
address provided.
Important
Electrical
Safety Instructions
Read all instructions
before using this appliance
Avoid fire hazard or electric
shock. Do not use an extension cord or an
adapter plug. Do not remove any prong
from the power cord.
Grounding type
wall receptacle
For Your Safety
Do not store or use gasoline or other flammable vapors and
liquids in the vicinity of this unit or any other appliance. Read
product labels for flammability
and other warnings.
Child Safety
Destroy carton, plastic bags, and any exterior
wrapping material immediately after the appliance
is unpacked. Children should never use these items
for play. Cartons covered with rugs, bedspreads,
plastic sheets or stretch wrap may become airtight
chambers and can quickly cause suffocation.
Remove all staples from the carton. Staples can
cause severe cuts, and destroy finishes if they come
in contact with other appliances or furniture.
An empty, discarded ice box, refrigerator, or freezer
is a very dangerous attraction to children.
Remove and discard any spacers used to secure the
shelves during shipping. Small objects are a choke
hazard to children.
Power supply
cord with 3-prong
grounding plug
Refer to the serial plate for correct electrical rating.
The power cord of the appliance is equipped with a
three-prong grounding plug for protection against shock
hazards. It must be plugged directly into its own properly
grounded three-prong receptacle, protected with a 15
amp time delay fuse or circuit breaker. The receptacle
must be installed in accordance with the local codes and
ordinances. Consult a qualified electrician. Receptacles
with Ground Fault Circuit Interrupters (GFCI) are NOT
RECOMMENDED. DO NOT USE AN EXTENSION
CORD OR AN ADAPTER PLUG.
If the voltage varies by 10 percent or more, appliance
performance may be affected. Operating the appliance
with insufficient power can damage the motor. Such
damage
isnotcovered
underthewarranty.
Ifyoususpect
yourvoltage
ishighorlow,consult
yourpower
company
fortesting.
Toprevent
theappliance
frombeingturned
off
accidentally,
donotplugtheunitintoanoutletcontrolled
byawallswitch
orpullcord.
DONOTpinch,knot,orbendthepower
cordinany
manner.
4.
Remove the four scews holding the wood skid to the
bottom of the unit using a 3/8" socket wrench. See Figure
1. Discard the wood skid and screws.
8.
Remove and discard the two front brackets with leg
leveler using a 5/16" socket wrench. See Figure 1.
6.
FOR GLASS DOOR MODELS ONLY - Remove bottom
door support bracket and screw opposite the door hinge
using a 3/8" socket wrench. See Figure 2.
Other Precautions
JJ
•
NEVER unplug the appliance by pulling on the power
cord. Always grip the plug firmly and pull straight out from
the receptacle.
Figure
1
To avoid electrical shock, unplug the appliance before
cleaning.
NOTE: Turning the control to "OFF" turns off the compressor
does not disconnect power to other electrical components.
Caster
Installation
Inspection
but
Screws
and Set-up
for Damage
Inspect the underside of the cabinet and packaging for damage,
similar to what can be caused with a forklift. If hidden damage
is found after uncrating, immediately call the delivery carrier
and request an inspection. Retain all packaging and crating
materials until the inspection is complete.
Skid
Wood Skid
Parts and Accessories
Check to make sure that you have received the box containing
all of the components listed below.
A
Carriage Bolt (4)
D
Fixed Caster (2)
B
Lock Nut (4)
E
Hex Screw (10)
C
Swivel Caster (2)
A
Tools
B
Figure 2
E
C
Needed
The following tools are required to assemble and install the
casters to the unit:
5/16", 3/8" and 9/16"
Socket or Open End
Wrench
Uncrating
Adjustable Wrench
or Pliers
Support Bracket
Phillips c_
Screwdriver
and Set-up
1.
Remove carton and all loose parts from inside the unit.
2.
Remove the rear access guard and place it and the
screws in a safe place for reassembly later.
3.
Using an assistant, carefully tip the unit onto its back and
rest on blocks to avoid damaging the condensate drain
hose and the plastic raceway that covers the evaporator
tubing on the back of the cabinet.
Front Fixed Caster Installation
1.
Locate and align fixed caster (with brake lever facing
front of unit - see Figure 3) over the same mounting
holes from bracket in Figure 1 using six hex screws (3 for
each caster). Secure the screws snug using a 3/8" open
end wrench. Repeat this procedure for opposite corner.
DO NOT OVERTIGHTEN.
Rear Swivel
Caster
Installation
1.
Remove and discard the screws shown in Figure 4 from
each bottom corner using a 5/16" socket wrench.
2.
Locate and align swivel caster over the holes and install
with two hex screws. Secure the screws snug using a
3/8" socket wrench. DO NOT OVERTIGHTEN.
3.
On the opposite side of the swivel caster plate, insert
two carriage bolts through the compressor support rail
and swivel caster plate. Use a lock nut on each bolt and
tighten securely using a 9/16" socket wrench. See Figure
5.
4.
Repeat the same procedure for the opposite rear corner.
5.
With the help of an assistant, carefully upright the unit.
Reassemble the rear access guard with screws.
Unit wifl roll forward
asit
is tipped
up.
Figure 5
Appliance
Placement
Leave a one (1) inch space on all sides and the back of the
cabinet for ease of installation, proper air circulation and
electrical connections. DO NOT block the front grill on the lower
front of your appliance. Sufficient air circulation is essential
for the proper operation of your appliance. Choose a place
that is near a grounded electrical outlet. For the most efficient
operation, the appliance should be located where surrounding
temperatures will not drop below 40°F (5°C) or exceed 110°F
(43°C). Additional compressor heaters are not recommended.
Insulation
The insulated space of this cabinet is sealed to maintain peak
efficiency. Holes drilled in the cabinet may destroy that seal and
damage electrical wiring located in the insulated space.
DAMANGED ELECTRICAL WIRING OR WET INSULATION
CAUSED BY DRILLING WILL VOID THE WARRANTY.
Appliance
Start-up
Once the appliance has been located in its permanent location
and the proper power and grounding has been provided, the
following items must be checked or completed:
Cool Down Period
Figure 3
For safe food storage, allow 24 hours for the appliance to cool
down completely before loading with food. The appliance will
run continuously for the first several hours. Do not place any
food in the appliance until after the first 24 hours of operation.
Thermostat Setting
The appliance is shipped from the factory with the thermostat
set at about the mid-point of the operating range. Adjustments
colder or warmer can be made after the appliance has
been running for at least 8 hours. Allow at least 8 hours for
temperature stabilization before re-adjusting the thermostat.
Defrost
Figure 4
Setting
The appliance is designed to defrost automatically every 12
hours. To set the time of defrost, wait until the desired time to
defrost. With the notch on the timer knob aligned with the line
on the bracket (Fig. A), turn the defrost timer knob clockwise
slowly. The timer will click several times, then once loudly,
at which point the defrost cycle begins. The timer knob will
advance through the defrost cycle, then click loudly at the end
of the cycle. The appliance will defrost automatically every 12
hours after the first defrost cycle.
Forexample,
tosettheappliance
todefrost
at10:00
AM,turn
thetimerknobclockwise
at10:00
AMuntilthetimerclicks
loudly.
Theappliance
willdefrost
dailyat10:00
AMandagain
12hourslaterat10:00PM.NOTE:The
appliance
interior
temperature
willriseduring
thefirstdefrost
cycle.
Door Locks
NOTE: The lock strike should angle out and away from the
cabinet.
Install the lock strike on the lock side of the cabinet using
the three tamper resistant screws
•
©
Install the lock guard in the side of the door cabinet by
installing the two screws into the corresponding screw
holes.
The tamper resistant screws cannot be
removed after the lock strike is secured to the cabinet.
Cabinet
)oor
.®
Figure A
i
i
rews
Screws
Features
e
e
e
e
e
e
e
e
e
e
e
e
e
Heavy duty epoxy powder coated adjustable shelves
NSF certified top mounted evaporator
2-Yz" urethane foam cabinet insulation
Torsion spring door closer
Heavy duty fixed and swivel casters
17 watt fluorescent lamp
Stainless steel evaporator housing
Removable stainless steel drain cover
NSF Certified
Lock Guard-
Temperature
Gauge
This appliance is equipped with an NSF certified temperature
gauge to display cabinet internal temperature. The temperature
gauge is located on the top right side of the evaporator housing
inside the unit.
Adjustable temperature control
NSF certified interior
Heavy duty front grill
Heavy duty commercially rated elecrtrical harness
Heavy duty removable stainless steel shelf support
Shallow
Fluorescent
Regular
BoSom
This appliance is provided with four shelves. One goes on the
floor of the cabinet and the other three are placed in the metal
side supports wherever they are needed. The shallow shelf
goes in the upper position
Lamp (Glass Door Models)
The Glass Door Refrigerator is equipped with a 17 watt
fluorescent lamp. A ballast - lamp mismatch may result in poor
or no lighting.
If the lamp fails, replace with a lamp of the same type and
wattage. Also, replace a lamp that flickers continuously. This
could damage the ballast.
Turning the light off, when not in use, will save energy. However,
frequent ON-OFF cycling will reduce the lamp life.
Use only NSF certified lamp which can be ordered from
your Frigidaire Commercial Service Center by calling
1-866-738-1640.
Casters
Interior
The appliance comes with four casters; two with locks for the
front of the unit and two without locks for the back of the unit.
The casters allow the unit to be moved with ease, and then
locked into place upon final designation. (Refer to pages 3-4 for
instructions.)
Light (Stainless
Steel Door Models)
The Stainless Steel Door models are equipped with a 40 watt
bulb that lights up when the door is opened. If the bulb goes
bad, replace with bulb of the same type and wattage. This is
a special bulb with a shatterproof coating. Use only an NSF
certified bulb of the same type and wattage which can be
ordered from your Frigidaire Commercial Service Center by
calling 1-866-738-1640.
Routine
Maintenance
Periods of Non=use and Moving Tips
Cleaning the interior
Be sure to turn the temperature control to "OFF" and unplug the
electrical cord. Wash the inside surface of the storage area with
warm water and baking soda solution (about one tablespoon
of baking soda per quart of warm water). Rinse thoroughly with
clean, warm water and wipe dry.
Leave the appliance operating during periods of non-use of less
than three (3) weeks.
Long Periods of Non=use
If the appliance will not be used for several months:
•
Remove all food and unplug the power cord.
Cleaning the Exterior
•
Clean and dry the interior thoroughly.
Wipe the cabinet exterior occasionally with a cloth dampened in
mild detergent and water. Rinse and wipe dry with a soft cloth.
Do not use razor blades or other sharp instruments that can
scratch the appliance surface when removing adhesive labels.
Any glue left from the tape can be removed with a mixture of
warm water and mild detergent or touch the residue with the
sticky side of tape already removed. DO NOT REMOVE THE
SERIAL PLATE.
•
Leave the appliance door open slightly, blocking it open if
necessary, to prevent odor and mold growth.
Condensate
Pan
Some models have a condensate pan in a fixed position located
behind the toe grill.This must not be removed from under the
cabinet. If the pan is removed, condensate will drop onto the
floor.
Power Failure
DO NOT open the appliance lid unnecessarily
off for several hours.
if the appliance is
If a power failure occurs, pack seven or eight pounds of dry ice
into the appliance every 24 hours. Look in the Yellow Pages
under "Dry Ice", "Dairies", or "Ice Cream Manufacturers" for local
dry ice suppliers. Always wear gloves and use caution when
handling dry ice.
Energy
Conservation
Measures
This appliance is designed for efficiency with heavy foam
insulation. However, there are things that the user can do to
maintain the appliance in operating condition.
•
Do not operate the appliance any colder than necessary
to maintain safe, product storage temperatures.
Make sure the appliance is located to prevent direct
exposure to sunlight, air ducts, etc.
Keep the door closed except for normal use. Inspect the
door often to see that it self-closes and the gaskets are in
good condition.
Do not overstock the product in the cabinet because it
will block the normal air flow.
Have at least annual inspections by a qualified service
company to see that the refrigerant charge is correct.
This appliance operates more efficiently in a cooler
ambient than in a hot ambient.Try to maintain an ambient
below 80°F (27°C) and 65% RH (Relative Humidity) for
maximum efficiency.
Moving
When moving the appliance,
damage:
follow these guidelines to prevent
•
Disconnect the power cord plug from the wall outlet.
•
Remove foods, then defrost, and clean the appliance.
Secure all loose items such as base panel, baskets,
and shelves by taping them securely in place to prevent
damage.
In the moving vehicle, secure appliance in an upright
position to prevent movement. Also, protect outside of
appliance with a blanket or similar item.
TROUBLESHOOTING
GUIDE
Before calling for service, review this list. It may save you time and expense. This list includes
common occurrences that are not the result of defective workmanship or materials in this
appliance.
PROBLEM
APPLIANCE
CAUSE
CORRECTION
* Appliance is plugged into a circuit
that has a ground fault interrupt.
* Temperature control is in the "OFF"
* Use another circuit. If you are unsure about the outlet,
have it checked by a certified technician.
* See Thermostat Setting.
OPERA TION
Appliance does not run.
position.
* Appliance may not be plugged in, or * Ensure plug is tightly pushed into outlet.
plug may be loose.
* House fuse blown or tripped circuit
* Check!replace fuse with a 15 amp time delay fuse.
breaker.
Reset circuit breaker.
* Power outage
Appliance runs too much or * Room or outside weather is hot.
too long.
* Appliance has recently been
disconnected for a period of time.
* Large amount of warm or hot food
* It takes 24 hours for the appliance to cool down
completely.
* Warm food will cause appliance to run more until the
have been stored recently.
* Door is opened too frequently or
desired temperature is reached.
* Warm air entering the appliance causes it to run
kept open too long.
* Appliance door may be slightly
* Temperature control is set too low.
more. Open the door less often.
* See "Door Problems".
* Appliance gaskets are dirty, worn,
cracked or poorly fitted.
Interior appliance
temperature is too cold.
* Temperature
Interior appliance
temperature is too warm.
* Temperature control is set too
warm.
* Door is opened too frequently or
control is set too low.
kept open too long.
* Appliance door may be slightly
* Large amount of warm or hot food
have been stored recently.
* Appliance has recently been
Appliance external surface
temperature is warm.
* Check house lights. Call local Electric Company.
* It's normal for the appliance to work harder under
these conditions.
* Turn control knob to a warmer setting. Allow several
hours for the temperature to stabilize.
* Clean or change gasket. Leaks in the lid seal will
cause appliance to run longer in order to maintain
desired temperature.
* Turn control knob to a warmer setting. Allow several
hours for the temperature to stabilize.
* Turn control knob to a colder setting. Allow several
hours for the temperature to stabilize.
* Warm air entering the appliance causes it to run
more. Open the door less often.
* See "Door Problems".
* Wait until the appliance has had a chance to reach its
selected temperature.
* appliance requires 24 hours to cool down completely.
disconnected for a period of time.
* The external appliance walls can be * This is normal while the compressor works to transfer
as much as 30°F warmer than room
heat from inside the appliance cabinet.
temperature.
SOUND AND NOISE
Louder sound levels
whenever appliance is on.
Louder sound levels when
compressor comes on.
Popping or cracking sound
when compressor comes
on.
* Modern appliances have increased
storage capacity and more stable
temperatures. They require heavy
duty compressors.
* Appliance operates at higher
pressures during the start of the ON
cycle.
* Metal parts undergo expansion and
contraction, as in hot water pipes.
* This is normal. When the surrounding noise level is
low, you might hear the compressor running while it
cools the interior.
* This is normal. Sound will level off or disappear as
appliance continues to run.
* This is normal. Sound will level off or disappear as
appliance continues to run.
PROBLEM
l
CAUSE
j
CORRECTION
SOUND AND NOISE (Cont.)
Bubbling or gurgling sound,
* Refrigerant (used to cool appliance)
is circulating throughout the system.
* Appliance is not level. It rocks on
the floor when it is moved sliqhtlv.
• Floor is uneven or weak.
Vibrating or rattling noise.
* This is normal.
* Level the appliance by putting wood or metal shims
under part of the appliance.
* Ensure floor can adequately support appliance. Level
the appliance by putting wood or metal shims under
part of the appliance.
* Re-level appliance or move appliance slightly.
• appliance is touching the wall.
WATER / MOIS TURE / FROS T INSIDE A PPL IA NCE
Moisture forms on inside
appliance walls.
[* Weather is hot and humid, which
1* This is normal.
R
E
| increases internal rate of frost build-_
/ up.
I
I * Door is slightly open.
I * See "Door Problems".
B
|
* opened
oor is kept
open tooV.long or is
too frequent
* Open the door less often.
ODOR IN APPLIANCE
Odors in appliance.
* Clean interior with sponge, warm water, and baking
soda.
strong
are in the
i Foods
Interior with
needs
to beodors
cleaned.
appliance.
• Cover the food tightly.
DOOR PROBLEMS
Door will not close.
the floor when it is moved slightly.
* Appliance is not level. It rocks on
* Floor is uneven or weak.
* Level the appliance by putting wood or metal shims
under part of the appliance.
* Ensure floor can adequately support appliance. Level
the appliance by putting wood or metal shims under
part of the appliance.
LIGHTING PROBLEMS
Light bulb is not on.
FOR QUESTIONS,
1-866-738-1640.
*
he fluorescent lamp or light bulb is * See "Fluorescent Lamp" or "Interior Light" on
Features Section.
burned out.
_
....
• See "appliance Does Not Run".
No electric current is reaching the
appliance.
COMMENTS
OR SERVICE
PLEASE
CALL
US TOLL FREE AT
IMPORTANT SAFETY NOTICE
The information provided herein is designed to assist qualified repair personnel only.
Untrained persons should not attempt to make repairs due to the possibility of electrical
shock. Disconnect the power cord before servicing.
ELECTRICAL
F
BLK
_nJiiE FJ
f-'-"l
BLLI
.
CIRCUIT
BLK
I
YF[ L=_
BLK
_=
='=1=
L
J
BLU
_
I
YkL
U
_L
II
L
"
J
OR
OR
3EFF_I
my_
_H
J
STAINLESS STEEL DOOR
REFRIGERATOR
STAINLESS STEEL DOOR
FREEZER
GLASS DOOR
REFRIGERATOR
OverJosd
White
IMPORTANT
IF ANY GREEN GROUNDING WIRES ARE REMOVED DURING SERVICING, THEY MUST BE RETURNED
TOTHEIR ORIGINAL POSITION AND PROPERLY SECURED.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement