SITOP Power Supply Order Overview

SITOP Power Supply Order Overview
© Siemens AG 2017
Output/Type
Rated input voltage
(range)
Dimensions in Article No.
mm (WxHxD) Siemens1)
Short description
Expansion modules to increase system availability
Signaling module for SITOP
modular 6EP1...-3BA00
Rating
240 V AC/6 A
25 x 125 x 125
6EP1961-3BA10
• Signaling contacts and remote ON/OFF
switching
Redundancy module, PSE202U
• 24 V/10 A
24 V DC (19 … 29 V DC)
30 x 80 x 100
6EP1964-2BA00
• Decouples SITOP power supplies of the
same type
• 24 V/10 A: 2 x 5 A or 1 x 10 A
• 24 V/NEC Class2:
2 x 5 ... 40 A with limiting of output to
Class2 – limit 100 VA
• 24 V/40 A:
power supplies 5 ... 20 A or 1 x 40 A
• 24 V/NEC Class2
24 V DC (19 … 29 V DC)
30 x 80 x 100
6EP1962-2BA00
• 24 V/40 A
24 V DC (24 … 28.8 V DC)
70 x 125 x 125
6EP1961-3BA21
Buffer module PSE201U for
24 V DC (24 … 28.8 V DC)
SITOP modular and SITOP smart
70 x 125 x 125
6EP1961-3BA01
Selectivity module PSE200U:
with common alarm signal
• 4x 0.5 ... 3 A
24 V DC (22 … 30 V DC)
72 x 80 x 72
6EP1961-2BA11
• 4x 0.5...3 A NEC Class 2 NEU 24 V DC (22 … 30 V DC)
72 x 80 x 72
6EP1961-2BA51
• 4x 3 … 10 A
24 V DC (22 … 30 V DC)
72 x 80 x 72
6EP1961-2BA21
24 V DC (22 … 30 V DC)
72 x 80 x 72
6EP1961-2BA31
with single-channel signaling
• 4x 0.5 ... 3 A
• 4x 0.5 ... 3 A NEC Class 2 NEU 24 V DC (22 … 30 V DC)
72 x 80 x 72
6EP1961-2BA61
• 4x 3 … 10 A
24 V DC (22 … 30 V DC)
72 x 80 x 72
6EP1961-2BA41
Diagnosis module SITOP select
4x 2 … 10 A
24 V DC (22 … 30 V DC)
72 x 90 x 90
6EP1961-2BA00
• Bridges power failures for up to a
period of seconds
• Selectivity/diagnosis module for selective
protection of 24 V DC paths and fast fault
localization
• Versions with power limitation of each
output to 100 VA according to NEC Class 2
• With group signaling contact or singlechannel signaling for channel-specific
evaluation via SIMATIC S7 function blocks
or LOGO! software
• Manual activation and deactivation of
feeders via reset button
• Remote reset for temporary faults
• Voltage measuring point for output current
• Sequential connection reduces total inrush
current
Maintenance-free SITOP DC UPS with capacitors – Uninterruptible power supply up to minutes
24 V DC/15 A, 2.5 kWs,
UPS500S
24 V DC (22 … 29 V DC),
24 V DC SITOP
24 V DC/15 A, 5 kWs,
UPS500S
120 x 125 x 125
6EP1933-2EC41
120 x 125 x 125
6EP1933-2EC51
24 V DC/15 A, 5 kWs,
UPS501S
24 V DC, UPS500S
70 x 125 x 125
6EP1935-5PG01
24 V DC/7 A, 5 kWs,
UPS500P
24 V DC (22.5 … 29 V DC),
24 V DC SITOP
400 x 80 x 80
6EP1933-2NC01
470 x 80 x 80
6EP1933-2NC11
24 V DC/7 A, 10 kWs,
UPS500P
• DC UPS modules with integral energy
buffer, digital inputs and outputs
(UPS500S) and USB interface
• Totally maintenance-free DC UPS with
double-layer capacitors
• SITOP UPS500S for DIN-rail mounting
can be combined with up to 3 expansion
modules UPS501S
• SITOP UPS500P in degree of protection IP65
for distributed use outside the control cabinet
• Capacitors eliminate battery replacement
• Long service life even at high ambient
temperature
• No ventilation of the mounting location is
necessary
• SW tool (free download) supports further
processing and response of the PC
DC-UPS with battery modules – uninterruptible power supply up to hours,
optionally with Ethernet/PROFINET connection and TIA integration
SITOP UPS1600, 24 V DC/10 A
24 V DC (22 … 29 V DC),
input voltage via 24 V DC
SITOP power supply unit
50 x 125 x 125
6EP4134-3AB00-0AY0
50 x 125 x 125
6EP4134-3AB00-1AY0
• with Ethernet/
PROFINET interface (2 ports)
50 x 125 x 125
6EP4134-3AB00-2AY0
SITOP UPS1600, 24 V DC/20 A
50 x 125 x 125
6EP4136-3AB00-0AY0
• with USB interface
50 x 125 x 125
6EP4136-3AB00-1AY0
• with Ethernet/
PROFINET interface (2 ports)
50 x 125 x 125
6EP4136-3AB00-2AY0
SITOP UPS1600, 24 V DC/40 A
70 x 125 x 150
6EP4137-3AB00-0AY0
• with USB interface
70 x 125 x 150
6EP4137-3AB00-1AY0
• with Ethernet/PROFINET
interface (2 ports)
70 x 125 x 150
6EP4137-3AB00-2AY0
89 x 130 x 107
6EP4131-0GB00-0AY0
190 x 169 x 80
6EP4133-0GB00-0AY0
• with USB interface
SITOP UPS1100
• 24 V DC/1.2 Ah
• 24 V DC/3.2 Ah
• 24 V DC/7 Ah
• 24 V DC/12 Ah
• 24 V DC/2.5 Ah, extended
temperature range
• 24 V DC/5 Ah, LiFePo
1)
End-of-charge voltage,
automatically set by UPS1600:
Battery modules UPS1100
1.2/2.5/3.2/7/12 Ah:
28.0 … 27.3 V DC (< + 20 °C),
26.8 ... 26.3 V DC (> +20 °C)
Battery module UPS1100
5 Ah LiFePo:
28.8 V DC (-20 ... +50 °C)
186 x 186 x 110
6EP4134-0GB00-0AY0
253 x 186 x 110
6EP4135-0GB00-0AY0
265 x 115 x 76
6EP4132-0GB00-0AY0
• DC UPS module with digital inputs/outputs,
with USB or Ethernet/Profinet interfaces as
option
• Maintenance-free UPS1100 battery modules
with automatic detection by UPS1600
• UPS 1100 5 Ah in Lithium technology
(LiFePo) with a long durability at high
temperature
• Intelligent battery management for
monitoring operational readiness, battery
supply line and battery charge status.
Selection of optimum, temperature-driven
charging characteristic
• High overload capacity and high charging
current
• Minimum standby consumption
• Integrated Web server
• SITOP UPS Manager (free SW download)
supports configuration and monitoring in
PC-based systems
• Complete integration into TIA:
User-friendly engineering in the TIA Portal,
function blocks for S7 user programs and
WinCC faceplates (free download)
• NEW: Integrated OPC UA server
189 x 186 x 112.7 6EP4133-0JB00-0AY0
Current ordering data plus terms and conditions of sale and delivery can be found in the Catalog KT10.1
and in the Internet at: www.siemens.com/industrymall
www.siemens.com/sitop
All product designations may be trademarks or product names of Siemens AG or
supplier companies whose use by third parties for their own purposes could violate
the rights of the owners.
Siemens AG
Process Industries and Drives
Process Automation
Postfach 48 48
90026 Nürnberg
Germany
© Siemens AG 2017
Subject to change without prior notice
PDF
BR 0417 10 En
Produced in Germany
Siemens provides products and solutions with industrial security functions that
support the secure operation of plants, systems, machines and networks. In order
to protect plants, systems, machines and networks against cyber threats,
it is necessary to implement – and continuously maintain – a holistic, state-oftheart industrial security concept. Siemens’ products and solutions only form
one element of such a concept. Customer is responsible to prevent unauthorized
access to its plants, systems, machines and networks. Systems, machines
and components should only be connected to the enterprise network or the
internet if and to the extent necessary and with appropriate security measures
(e.g. use of firewalls and network segmentation) in place. Additionally,
Siemens’ guidance on appropriate security measures should be taken into
account. For more information about industrial security, please visit
http://www.siemens.com/industrialsecurity.
The information provided in this brochure contains merely general descriptions or
characteristics of performance which in case of actual use do not always
apply as described or which may change as a result of further development of the
products. An obligation to provide the respective characteristics shall only exist if
expressly agreed in the terms of contract. Availability and technical specifications
are subject to change without prior notice.
Siemens’ products and solutions undergo continuous development to make
them more secure. Siemens strongly recommends to apply product updates as
soon as available and to always use the latest product versions. Use of product
versions that are no longer supported, and failure to apply latest updates may
increase customer’s exposure to cyber threats. To stay informed about product
updates, subscribe to the Siemens Industrial Security RSS Feed under
http://www.siemens.com/industrialsecurity.
Security information
SITOP Power Supply
SITOP Power Supply
Top Integration. Top Efficiency. Top Reliability.
Order
overview
Edition
04/2017
siemens.com/sitop
© Siemens AG 2017
Order overview SITOP
Regulated Power Supplies, Expansion modules and DC UPS
Output/Type
Rated input voltage
(range)
Dimensions in Article No.
mm (WxHxD) Siemens1)
hort description
SITOP compact – Slim power supply for control boxes
12 V DC/2.0 A, PSU100C
100 – 230 V AC
(85 ... 264 V AC/
110 … 300 V DC)
30 x 80 x 100
6EP1321-5BA00
52.5 x 80 x 100
6EP1322-5BA10
24 V DC/0.6 A, PSU100C
22.5 x 80 x 100
6EP1331-5BA00
24 V DC/1.3 A, PSU100C
30 x 80 x 100
6EP1331-5BA10
24 V DC/2.5 A, PSU100C
45 x 80 x 100
6EP1332-5BA00
24 V DC/3.7 A, PSU100C
NEC Class2
52.5 x 80 x 100
6EP1332-5BA20
24 V DC/4.0 A, PSU100C
52.5 x 80 x 100
6EP1332-5BA10
12 V DC/6.5 A, PSU100C
• Mini power supply for small mounting
surface thanks to slim design
• Wide-range input AC and DC
• High efficiency over the entire load range
• Low energy consumption < 0.75 W
• Green LED for “Output voltage o.k.
• Adjustable output voltage
• Plug-in terminal
• NEC class 2 variant with power limitation
to 100 VA
• Temperature range –20 ... +70 °C
LOGO!Power – Flat power supply for distribution boards in LOGO! 8 design 2)
5 V DC/3.0 A
100 – 240 V AC
(85 … 264 V AC/
110 … 300 V DC)
5 V DC/6.3 A
12 V DC/0.9 A
36 x 90 x 53
6EP3310-6SB00-0AY0
54 x 90 x 53
6EP3311-6SB00-0AY0
18 x 90 x 53
6EP3320-6SB00-0AY0
12 V DC/1.9 A
36 x 90 x 53
6EP3321-6SB00-0AY0
12 V DC/4.5 A
54 x 90 x 53
6EP3322-6SB00-0AY0
15 V DC/1.9 A
36 x 90 x 53
6EP3321-6SB10-0AY0
15 V DC/4.0 A
54 x 90 x 53
6EP3322-6SB10-0AY0
24 V DC/0.6 A
18 x 90 x 53
6EP3330-6SB00-0AY0
24 V DC/1.3 A
36 x 90 x 53
6EP3331-6SB00-0AY0
24 V DC/2.5 A
54 x 90 x 53
6EP3332-6SB00-0AY0
24 V DC/4.0 A
72 x 90 x 53
6EP3333-6SB00-0AY0
• Small. Clever. LOGO!Power:
The 4th generation with even more power
in a smaller space
• Overall width reduced by 18 mm (1 modular
width) in each performance class
• New performance class only 18 mm wide
• Wide-range AC and DC input
• Voltage measuring point for output current
• Up to 90% efficiency over entire load
range
• Very low no-load losses of < 0.3 %
• Constant current and power reserve when
starting up for loads with high inrush
currents
• Flexible rail or wall mounting
• Green LED for “Output voltage OK”
• Adjustable output voltage
• Temperature range -25 ... +70 °C
SITOP lite – Cost-effective basic power supply
24 V DC/2.5 A, PSU100L
120/230 V AC
(85 ... 132/170 ... 264 V AC)
24 V DC/5 A, PSU100L
24 V DC/10 A, PSU100L
24 V DC/20 A, PSU100L
NEU 120/230 V AC (85 ... 264 V AC)
32.5 x 125 x 120
6EP1332-1LB00
50 x 125 x 120
6EP1333-1LB00
70 x 125 x 120
6EP1334-1LB00
110 x 125 x 125
6EP1336-1LB00
50 x 125 x 120
6EP1322-2BA00
70 x 125 x 120
6EP1323-2BA00
• For industrial applications and basic
requirements
• Narrow width
• Green LED for “24 V OK”
• Adjustable output voltage
88 ... 370 V DC
SITOP smart – Powerful standard power supply
12 V DC/7 A, PSU100S
120/230 V AC
(85 … 132/170 … 264 V AC)
12 V DC/14 A, PSU100S
24 V DC/2.5 A, PSU100S
32,5 x 125 x 120
6EP1332-2BA20
24 V DC/5 A, PSU100S
50 x 125 x 120
6EP1333-2BA20
24 V DC/10 A, PSU100S
70 x 125 x 120
6EP1334-2BA20
24 V DC/20 A, PSU100S
115 x 145 x 150
6EP1336-2BA10
24 V DC/5 A, PSU300S
400 – 500 V 3 AC
(340 … 550 V 3 AC)
24 V DC/10 A, PSU300S
50 x 125 x 120
6EP1433-2BA20
70 x 125 x 120
6EP1434-2BA20
24 V DC/20 A, PSU300S
90 x 145 x 150
6EP1436-2BA10
24 V DC/40 A, PSU300S
150 x 145 x 150
6EP1437-2BA20
• Space-saving, slim design
• PSU100S with automatic range switch
over 120/230 V AC
• Extra-Power (1.5 x Irated for 5 s)
for brief operational overload
• Permanent overload capacity (1.2 x Irated)
to 45 °C ambient temperature
(24 V devices)
• Green LED and signaling contact „Output
voltage OK”
• Adjustable output voltage up to 28.0 V DC
or 15.5 V DC (12 V devices)
• Expandable with, redundancy module,
selectivity/diagnostics module, buffer
module and DC UPS
SITOP modular – Technology power supply for demanding solutions
24 V DC/5 A, PSU8200
120/230 V AC
(85 … 132/176 … 264 V AC)
24 V DC/10 A, PSU8200
24 V DC/5 A, PSU200M
120-230/230-500 V AC
(85 … 264/176 … 550 V AC)
45 x 125 x 125
6EP3333-8SB00-0AY0
55 x 125 x 125
6EP3334-8SB00-0AY0
70 x 125 x 125
6EP1333-3BA10
70 x 125 x 125
6EP1334-3BA10
24 V DC/20 A, PSU8200
120/230 V AC
90 x 125 x 125
(85 … 275 V/DC 88 … 350 V AC)
6EP1336-3BA10
24 V DC/40 A, PSU8200
120/230 V AC
(95 … 132/190 … 264 V AC)
6EP3337-8SB00-0AY0
24 V DC/20 A, PSU8200
400 – 500 V 3 AC
(320 … 575 V 3 AC)
24 V DC/10 A, PSU200M
24 V DC/40 A, PSU8200
36 V DC/13 A, PSU8200
48 V DC/10 A, PSU8200
NEU
48 V DC/20 A, PSU300M
400 – 500 V 3 AC
(340 … 550 V 3 AC)
145 x 145 x 150
70 x 125 x 125
6EP3436-8SB00-0AY0
150 x 125 x 150
6EP1437-3BA10
70 x 125 x 125
6EP3446-8SB10-0AY0
70 x 125 x 125
6EP3446-8SB00-0AY0
240 x 125 x 125
6EP1457-3BA00
• Wide-range input
• Efficiency levels of up to 94%
• Extra power feature (1.5 x IN for 5 s/min
for brief operational overload
• Power Boost (3 x Irated for 25 ms)
for triggering protective equipment
• Switchable characteristic curves for
parallel operation and short-circuit
protection
• Operation status indicated by 3 LEDs
• Output voltage adjustable
• 24 V power supply units expandable with
add-on modules and DC UPS
• 36 V and 48 V versions enable smaller
cross-sections of the load supply lines
SITOP modular – Power supply system SITOP PSU8600 with complete TIA integration
PSU8600 basic unit
• 24 V DC/20 A
• 24 V DC/20 A/4 x 5 A
• 24 V DC/40 A
• 24 V DC/40A/4 x 10 A
80 x 125 x 150
100 x 125 x 150
125 x 125 x 150
125 x 125 x 150
6EP3436-8SB00-2AY0
6EP3436-8MB00-2CY0
6EP3437-8SB00-2AY0
6EP3437-8MB00-2CY0
Supply from basic unit
PSU8600 via connection
System Clip Link
60 x 125 x 150
60 x 125 x 150
6EP4436-8XB00-0CY0
6EP4437-8XB00-0CY0
60 x 125 x 150
125 x 125 x 150
60 x 125 x 150
125 x 125 x 150
6EP4297-8HB00-0XY0
6EP4297-8HB10-0XY0
6EP4293-8HB00-0XY0
6EP4295-8HB00-0XY0
70 x 100 x 75
6EP1332-1SH71
• Compact Power Module for the S7-1200
with automatic range switchover
• System and load power supply for the
S7-300 in new narrow design with
automatic range switchover
Modular system:
CNX8600 expansion module
• 24 V DC/4 x 5 A
• 24 V DC/4 x 10 A
• Compact basic units with 1 or 4 outputs,
each overload monitored
• Expandable without wiring effort: Up to
4 CNX8600 modules (for max. 20 outputs)
and up to 2 BUF8600 modules (for max.
20 s DC buffering at 40 A, accordingly
longer buffer times at lower load currents)
• Outputs individually adjustable:
Voltage (5 - 28 V DC) and current
• Two Ethernet/PROFINET ports for optimum
integration in machines and plants
• NEW: Integrated OPC UA server
• Simple engineering and comprehensive
monitoring and diagnosis in TIA Portal
• Support of energy management due to
capturing energy data and switching off
the outputs selectivel
400-500 V 3 AC,
(320 … 575 V 3 AC)
BUF8600 buffer module
• 100 ms/40 A
• 300 ms/40 A
• 4 s/40 A
• 10 s/40 A
Power supply in SIMATIC Design
24 V DC/2.5 A, PM1207
120/230 V AC
(85 … 132/176 … 264 V AC)
24 V DC/2 A, PS307
120/230 V AC
(85 … 132/170 ... 264 V AC)
24 V DC/5 A, PS307
24 V DC/10 A, PS307
24 V DC/3 A, PM1507
24 V DC/8 A, PM1507
24 V DC/8 A, ET200pro PS
40 x 125 x 120
6ES7307-1BA01-0AA0
60 x 125 x 120
6ES7307-1EA01-0AA0
80 x 125 x 120
6ES7307-1KA02-0AA0
120/230 V AC
(85 … 132 V/170 ... 264 V AC)
50 x 147 x 135
6EP1332-4BA00
75 x 147 x 135
6EP1333-4BA00
400 – 480 V 3 AC
(340 ... 550 V 3 AC)
310 x 135 x 90
6ES7148-4PC00-0HA0
• Power supply in degree of protection
IP67 for electronics/sensors and load
voltage for the SIMATIC ET200pro
• Low-cost power supply for wall mounting
in various installation positions
• Rugged aluminum enclosure
• Wide-range input
• Temperature range from –10 to +70 °C
• Load power supply of S7-1500 in slimline
design with automatic range switchover
and extra power (1.5 x Irated for 5 s/min)
Power supplies in special design, for special uses
12 V DC/3 A, PSU100D
97 x 98 x 38
6EP1321-1LD00
97 x 158 x 38
6EP1322-1LD00
24 V DC/2.1 A, PSU100D
97 x 128 x 38
6EP1331-1LD00
24 V DC/3.1 A, PSU100D
97 x 128 x 38
6EP1332-1LD00
24 V DC/4.1 A, PSU100D
97 x 158 x 38
6EP1332-1LD10
24 V DC/6.2 A, PSU100D
97 x 178 x 38
6EP1333-1LD00
24 V DC/12.5 A, PSU100D
105 × 199 × 41
6EP1334-1LD00
120 – 230 V AC
(85 ... 132/170 ... 264 V AC)
160 x 130 x 60
6EP1333-1AL12
160 x 130 x 60
6EP1334-1AL12
120 – 230 V AC
(AC 85 ... 132/170 ... 264 V)
120 x 181 x 60
6EP1333-7CA00
24 V DC/8 A , ET200pro PS
400 – 480 V 3 AC
(340 ... 550 V 3 AC)
310 x 135 x 90
6ES7148-4PC00-0HA0
24 V DC/20 A, PSU400M
600 V DC (300 … 900 V DC)
90 x 125 x 125
6EP1536-3AA00
• PSU400M: DC/DC converter for drive/
battery networks
24 V DC/5 A, PSU300E
400 – 500 V 3 AC
(320 … 550 V 3 AC)
42 x 125 x 125
6EP1433-0AA00
• 3-phase power supply in a slim aluminium
housing
12 V DC/20 A, PSU3800
400 – 500 V 3 AC
(320 … 575 V 3 AC)
12 V DC/8.3 A, PSU100D
24 V DC/5 A in flat design
24 V DC/10 A in flat design
24 V DC/5 A, PSU100P
24 V DC/8 A, PSU100P
100 – 240 V AC
(85 … 264 V AC)
6EP1334-7CA00
150 x 125 x 150
6EP1437-3BA20
3-52 V DC/10 A, SITOP flexi
120/230 V AC
(85 … 132/170 … 264 V AC)
75 x 125 x 125
6EP1353-2BA00
• Continuously adjustable output voltage
2x15 V DC/3.5 A, SITOP dual
120/230 V AC (93 … 264 V AC)
75 x 125 x 125
6EP1353-0AA00
• Two 15 V DC outputs, e.g. for ± 15 V DC
24 V DC/30 A, PSU300B
70 x 125 x 125
6EP3424-8UB00-0AY0
6EP3436-8UB00-0AY0
• Rugged metal enclosure in IP67 degree
of protection for distributed use
• Signaling contact and LED for operation
status
• Optimized power supply for battery
charging; with selectable output
characteristic, functional expansion
possible using expansion modules
24 V DC/17 A, PSU3800
70 x 125 x 125
• Flat metal housing for DIN-rail mounting
Current ordering data plus terms and conditions of sale and delivery can be found in the Catalog KT10.1 and in the Internet at: www.siemens.com/industrymall
2)
Planned start of delivery: June 2016. The former product line (article no. 6EP13…, 3rd generation LOGO!Power) can be ordered until approx. end of 2017.
1)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement