Control 10 Series Owners Manual

Add to my manuals
9 Pages

advertisement

Control 10 Series Owners Manual | Manualzz

Control 10 Series

Ceiling Loudspeakers

Control 12C/T, Control 14C/T, Control 16C/T, Control 18C/T

Owner’s Manual

& Installation Guide

1

Rev B

Table of Contents Product Feature Identification

(Control 14C/T Shown)

Product Descripti on .................................................... 2

Product Feature Identification ................................... 2

I nstallation Preparations ............................................. 3

Step-By-Step Installation and Wiring ....................... 3

Painting the Speaker .................................................... 7

Safety Agency Compliance ......................................... 7

Maintenance ................................................................. 8

Replacement Parts ....................................................... 8

Contacting JBL ............................................................. 8

Product Specifications ................................................. 8

Tap Selector for

70V/100V taps, 8Ω direct and OFF

Zinc-Plated

Steel Backcan

Loudspeaker

Driver

Thank you for purchasing JBL Control Contractor ceiling loudspeakers. Read through this manual to familiarize yourself with the features, applications and precautions before you use these products.

Product Descriptions

The JBL Control Contractor Control 10 Series ceiling loudspeakers utilize innovative design and materials to provide premium level performance from compact inceiling speakers. Available in white or black (-BK).

CONTROL 12C/T – A 3” (75 mm) full-range driver to provide high-fidelity full-range sound over an extremely wide coverage area.

CONTROL 14C/T – A wide bandwidth ceiling speaker containing a co-axially mounted 4” (100 mm) woofer and

¾” (19 mm) soft-dome tweeter.

CONTROL 16C/T – A wide bandwidth, high sensitivity, extended bass ceiling speaker containing a co-axially mounted 6.5” (165 mm) woofer and ¾” (19 mm) softdome tweeter.

CONTROL 18C/T – A high-output, more narrow coverage extended bass ceiling speaker containing a co-axially mounted 8” (200 mm) woofer and 1” (25 mm) soft-dome tweeter.

Seismic Tab

(secondary support point)

Removeable

Locking Input

Connector

Attachment

Screws

Strain Reliefs

(x2)

Terminal Cover

Plate

Perforated

Press-In Grille

Rotating

Mounting Tabs

(dog-ears)

2

Installation Preparations

The entire installation can be accomplished, if necessary, without requiring access above the ceiling. Bracketry for use with either suspended ceilings or sheetrock ceilings is included. The speaker is held securely in place via mounting ears which lock into place. Inputs are attached to a removable locking connector (included) which can be prewired before installing the speaker for ultra-fast snap-on installation.

OPTIONAL PRE-INSTALLATION BRACKETS

IN MOST CASES, NO BRACKETS OTHER THAN THE

ONES INCLUDED WITH YOUR SPEAKER ARE REQUIRED.

Everything needed for most installations of these loudspeakers is provided with your Control Contractor ceiling speaker.

However, when the speaker is being installed into a sheet rock

(typically gypsum board) ceiling, JBL’s optional pre-installation brackets can be installed before the sheetrock is installed. The pre-installation bracket provides a bracket to which wiring can be tied behind the sheetrock. It can function as a cutout template when many cutouts are to be made in a production-line style installation, and it secures the ceiling speaker to the building structure. Two types of pre-installation brackets are available from JBL Professional as optional accessories:

1) The optional NEW-CONSTRUCTION BRACKET is made of flat sheetmetal, with wings to attach to the building structure.

Holes are drilled for nails or screws at 16 inches (406 mm) and

24 inches (610 mm) on-center. Additional holes can be drilled by the installer at other spacings up to a maximum of 24-3/4 inches (630 mm) apart. Sheet rock installs over the bracket, and the bracket provides a template for blind cutout of the hole in the sheet rock. The sheet rock is typically cut with a router-type cutting tool, using the bracket ring as a cutout guide.

Figure 2:

Optional MR Plaster-Ring Bracket (“Mud Ring”)

Table 1: New Construction Brackets

Model

Control 12C/T

New

Construction

Bracket

MTC-24NC

Plaster-Ring

Bracket

MTC-24MR

Control 14C/T

Control 16C/T

Control 18C/T

MTC-24NC

MTC-26NC

MTC-47NC

MTC-24MR

MTC-26MR

MTC-47MR

USING INCLUDED C-BRACKET WITH

SHEET-ROCK

For most installations, the INCLUDED C-shaped backing plate provides adequate reinforcement to the ceiling material, spreading out the clamping force from the tab clamps.

CUTOUT SIZES

Table 2: Cutout Sizes

Model

Control 12C/T

Control 14C/T

Control 16C/T

Control 18C/T

Cutout Size

(diameter)

167 mm (6.6 in)

167 mm (6.6 in)

225 mm (8.8 in)

282 mm (11.1 in)

Figure 1:

Optional NC New-Construction Bracket

2) The optional PLASTER-RING BRACKET (or “mud ring”) contains a circular offset, forming a edge guide for sheet rock plastering. The bracket has wings that attach to the building structure. Sheet rock is typically either precut or cut with a rotary cutting tool using the outside of the plaster ring circle as a guide. The sheet rock hole is then plastered (or “mudded”) up to the ring to create a seamless cutout.

3

STEP-BY-STEP

INSTALLATION AND WIRING

The installation system has been designed so that the entire installation can be accomplished from beneath the ceiling for instances when access above the tile is not possible or practical.

However, in some cases it may be easier with removable ceiling tiles to access from both the top and bottom of the ceiling tile during various phases of the installation.

Step 1 – Cut the Hole. Cutout the circular hole to the cutout hole size listed above. Pull the wiring through the cutout hole.

Figure 3:

Hole Cutout

Step 2 – Insert Backing Hardware Through the Hole. Packaged with the speakers are two types of backing hardware – a

C-shaped backing-plate bracket and two tile rails.

Suspended Ceilings – Insert the C-plate through the hole cut in the ceiling tile. Place the C-plate around the hole with the tabs located as shown on Figure 4. Insert the tile rails through the cut hole in the ceiling tile. Snap the two rails into the two tabs in the C-plate and align the rails so that the ends extend OVER the T-channel grid on the side of the tile.

Secure the rails onto the C-bracket tabs by inserting a screw though each tab into the rail. This can all be accomplished from below the ceiling tile, if necessary.

FOR SAFETY:

IMPORTANT TO USE BRACKETS

ALL included support brackets – C-plate and tile rails -- MUST be used when installing into suspended ceiling tiles.

Additional Suspended Ceiling Installation

Information

Tile Rails: The tile rails are designed to fit either standard

24-inch wide tiles or 600-mm wide tiles. The tile rail pieces do NOT physically attach to the T-grid struts. Instead, the inverted-V shape at the ends of the rails sit OVER the T-grid strut. During normal operation, the rails are supported by the edge of the tile. If the tile were to come out or fall apart, the ends of the support rails are designed to catch onto the T-grid, providing secure support to hold the loudspeaker assembly in place.

Vibration Reduction: Loudspeakers can generate substantial vibration which can cause buzzing of the ceiling materials or structure. Depending on the character of the ceiling tile and structure, the installer might need to place neoprene or other dampening material under the tile rails or the edges of the tiles to eliminate rattles.

Cutout Placement: The tile rails are pre-punched with attachment holes along their length. Placement is not limited to the center of the tile as is the case with many other tile rail support systems.

Non-Suspended Ceiling Types – The C-bracket can be optionally used by itself to shore up the ceiling material and to spread out the clamping force from the tab clamps. Insert the C-plate through the cut hole in the ceiling and place it on the back side of the hole before inserting the speaker.

Step 3 – Connect the Wiring to the Removable Locking

Connector – The connector is INCLUDED with the speaker.

Connect the wire by stripping the insulation back about 5 mm

(about 3/16 inch). Do NOT strip wires back any longer than this. Insert the bare end of wire fully into the connector (not allowing any bare wire outside of connector) and screw down the hold-down screw until tight using a small flatblade screwdriver.

Tighten any unused screws to avoid rattling from vibration.

Figure 4:

C-Bracket and Tile Rail Positioning on Ceiling Tile

Figure 5:

Connecting Wires to Removeable

Locking Connector

4

Guide to the Pins for Connection -- The removable locking input connector contains 4 terminals, as marked on the connector. The pin functions are listed on the label located on the terminal cover plate.

Figure 6

Connecteor Pins

Pins 1 & 2 are the “+” and “-” inputs to the loudspeaker. Pins 1

& 2 are looped to pins 3 & 4, respectively (Pin 1 connects to Pin

3 and Pin 2 connects to Pin 4) inside the speaker. Pins 3 & 4 are intended as loop-through connections to subsequent loudspeakers. There are two possible hookup schemes for connecting subsequent speakers, determined by the desired result from the circuit whenever this speaker’s connector gets disconnected during troubleshooting:

Paralleling Input Terminals -- Connect the wire pair of the subsequent speaker to pins 1 & 2 (in parallel with the input wire pair). Whenever the connector is pulled out of the speaker for troubleshooting, subsequent speakers will stay connected. This can be useful during troubleshooting to be able to disconnect a single loudspeaker at a time. In this hookup scheme, no wires get connected to pins 3 & 4.

From Amplifier or Previous

Speaker

+

-

Figure 9:

Using Loop-Through Terminals

-

+

To Subsequent

Speaker(s)

+

-

To

Subsequent

Speaker(s)

+ -

Power

Amplifier

Figure 10:

Loop-Through System Hookup Diagram

Choose whichever hookup pattern accommodates your installation best.

Step 4 – Open the Strain Relief Fitting / Terminal

Cover

From Amplifier or Previous

Speaker

Figure 7:

Paralleling Input Terminals

+ -

Power

Amplifier

Figure 8:

Parallel System Hookup Diagram

To Subsequent

Speaker(s)

Figure 11:

Open the strain relief fitting by loosening the two set screws in the backcan, then loosen the two horizontal screws, and slide open the sliding cover.

Loosen the screws holding the fitting’s sliding piece of the input-terminal cover and slide the cover open.

To

Subsequent

Speaker(s)

Step 5 – Plug connector into connector socket in the speaker’s terminal cup.

Using Loop-Through Terminals (Pins 3 & 4) -- By connecting the wire pair of the subsequent speaker to pins 3 & 4, then all subsequent speakers will be disconnected when this speaker’s connector is disconnected during troubleshooting,.

This can be useful as a way to isolate problems to a section of the distributed line while leaving the wires attached to the connector.

5

Figure 12:

Plug Connector into Connector Socket. Shown with a single cable (left) or with two cables for input and loop-through (right)

Step 6 – Tighten the Strain Relief Fitting & Close the Terminal Cover

Figure 13:

Tighten the Two Horizontal Screws to Slide and Tighten the

Strain Relief Fitting. Then Tighten the Two Set Screws into the

Backcan. (Shown with a single speaker cable)

Tightening onto Flexible or Hard Conduit – The supplied fitting accommodates up to 3/8 inch (9.5mm) flexible conduit. Insert the conduit into the strain relief fitting. Tighten the sliding

Strain Relief Fitting.

Step 7 – Insert the Speaker Into the Ceiling and

Tighten.

Figure 15:

Tightening Mounting Tabs

IMPORTANT -- For each attachment screw, FIRST turn ½ turn

COUNTER-CLOCKWISE to release the mounting tab from its guide.

Then tighten the mounting tabs by turning the screw CLOCK-

WISE until tight. The first ¼ clockwise turn rotates the attachment tabs outward and the remaining turns tighten the tabs down onto the back of the ceiling surface. DO NOT OVER-

TIGHTEN.

A tab is provided on the back of each speaker for connection to a independent secondary support point. Some construction codes require using this secondary support point, which requires connecting a support line to a separate secure support point. Consult construction codes in your region.

IMPORTANT -- Control Contractor ceiling speakers can generate substantial vibration . Using the seismic tab as a secondary support point is highly recommended in case the ceiling tile or structure breaks. In some areas, using the seismic tab as a secondary support point is required by code.

Figure 14:

Inserting Speaker into Ceiling

(C-ring/tile-rail assembly is above the ceiling tile. Speaker inserted through cutout in ceiling material. Diagram shown without cable and ceiling tile for clarity)

Insert the speaker into the ceiling as far as it goes, until the front baffle rim touches the ceiling.

Turn the attachment screws to tighten the mounting tabs, by using the following directions:

Step 8 Adjust Tap Selector

The tap selector rotary switch is located on the front baffle. Adjust the tap setting before applying power to the speaker and before inserting the grille. From the OFF position, turn the selector counter-clockwise to set to the 8Ω (low impedance) nominal setting (see spec sheet for more precise impedance information) or turn the selector clockwise to set to the various 70V and 100V distributed system tap settings.

6

Figure 16:

Tap Selector

(Shown: Control 14C/T. Tap ratings on the other models differ from these figures.)

Step 9 – Insert the Grille

Consider which direction the logo is facing and press the grille into place until the front of the grille is flush with the rim. It is often easiest to press in various places around the perimeter of the grille. Make sure grille is securely seated to prevent it from vibrating loose and falling.

Removing the Grille -- The grille presents a tight fit in order to make sure that it won’t fall out, even with high vibrations that can be produced by these speakers. If you need to remove the grille, it is easiest to do so by inserting 2 pointed objects (such as push pins) into 2 nearby holes in the grille, presenting slow even pressure to pull down on the grille until that section of the grille comes out approximately 6 mm (1/4 inch) . Work your way around the grille, loosening a section at a time until the grille comes out. primer is used first. Application can be made by rolling, brushing or spraying.

Painting the Speaker Along With the Ceiling – Insert the clear plastic paint shield into the front of the speaker to mask the drivers and internal baffle, paint the speaker, then remove the shield.

Painting the Grille – Painting the grille requires removal of the logo prior to painting (the logo should be stuck back onto the grille after painting, making sure it is located in the exact center of the grille).

The backing to the grille is glued in place so that it can’t interfere with the movement of the woofer cone. Leave the grille backing in place. Spray the grille lightly using thinned paint. Make sure the spray is light enough that when the grille is held up to the light, you can still see light through the grille holes (which means that sound can also get through). Spray only the front of the grille, not the back. Rolling or brushing the paint is discouraged because the mesh and/or backing may become clogged with paint and poor sound quality may result, however using a very short-napped roller can be made to work.

Safety Agency Compliance

S7232

Painting the Speaker

The speaker’s textured white finish complements most decor and does not need further finishing. Where the interior design requires it, these speakers are easy to paint.

The rim can be painted before installation or in cases where the rim needs to be finished along with the ceiling, the speaker rim can be painted after attaching into the ceiling.

Type of Paint – The speaker’s ABS rim accepts almost any type of latex or oil based paint. Two coats are recommended.

Painting Process – For best results, the following procedure is recommended:

LISTED

15CM

Signaling Speaker

UL-2043 Fire Tests for Heat and Visible Smoke Release for

Discrete Products and their Accessories Installed in Air Handling Spaces, NFPA-70 National Electric Code 1996, Article

300-22(C), and NFPA-90A Installation of Air Conditioning and

Ventilation Systems, Section 2-3.10.1 (a), Exception 3. Listed UL1480-6 Speakers for Fire Protective Signaling Systems.

SUITABLE FOR USE IN AIR HANDLING SPACES.

• Clean the rim and grille with a light solvent such as mineral spirits by rubbing the item with a lightly dampened cloth. Do not, however, use abrasives such as sandpaper or steel wool. Nor should you use gasoline, kerosene, acetone, MEK, paint thinner, harsh detergents or other chemicals. Use of these cleaners may result in permanent damage to the enclosure.

• After cleaning, apply two or more thin coats of either latex or oil-based paints. Latex paint will adhere best if an oil-based 7

These products are in compliance with the EMC Directive

89/336/EEC and Article 10 (1) of the directive. In compliance with Technical Regulations EN50081-1 and EN50082-1. For a copy of the model-specific CE Declaration of Conformity, contact JBL at the address listed at the end of this manual.

Maintenance

No maintenance is required when installed in accordance with installation and wiring guidelines described in this manual.

Replacement Parts

There are no user serviceable parts inside these speakers.

Refer servicing to an authorized JBL Service Center. For the name of an authorized Service Center in your area, contact JBL Professional at the address listed below.

Warranty & Contacting JBL

These products are designed and backed by JBL Professional, the world leader in sound reinforcement. For complete JBL warranty information, to order replacement parts or to ask for clarifications to this manual, contact JBL Professional:

WITHIN THE UNITED STATES: Contact the Applications

Dept, JBL Professional, PO Box 2200, 8500 Balboa Blvd,

Northridge CA 91329 USA. In the USA you may call Monday through Fiday 8:00 am to 5:00 pm Pacific Coast Time

(818) 894-8850.

IN OTHER AREAS THROUGHOUT THE WORLD: Contact the JBL Professional Distributor in your country.

A list of JBL Professional Distributors and U.S. Service

Centers can be obtained from the JBL Professional website at www.jblpro.com.

---------------------------------------------------------------------

1 Half-space (flush mounted in ceiling)

2 Continuous Pink Noise Rating is IEC-shaped pink noise with a 6 dB crest

factor for 100 hours continuously. Continuous Program Power is a

conservative expression of the system’s ability tohandle normal speech and

music program material, and is defined as 3 dB above the Continuous Pink

Noise Rating.

3 Half-space (in ceiling) average 1 kHz to 16 kHz.

JBL Professional

8500 Balboa Blvd, P.O. Box 2200

Northridge, CA 91329 U.S.A.

8

Product Specifications

See product specification sheets for complete specification listings.

Control 12C/T

Components: 76 mm (3 in) full-range driver

Frequency Range 1 : 68 Hz - 17 kHz

Power Capacity (low-Z): 40 W Cont. Program

Sensitivity 2

20 W Cont. Pink Noise

: 84 dB

Coverage 3 : 130˚

Max. SPL: 97 dB @ 1m ave., 103 dB peak

Nominal Impedance: 8 ohms (in direct/bypass 8Ω setting)

Transformer Taps: 15W, 7.5W, 3.8W @ 70V & 100V;

plus 1.9W @ 70V

Control 14C/T

Components: 100 mm (4 in) LF driver

19 mm (3/4 in) HF driver

Frequency Range

Sensitivity

1 : 74 Hz - 20 kHz

Power Capacity (low-Z): 60 W Cont. Program

Coverage

2

30 W Cont. Pink Noise

: 87 dB

3 : 120˚

Max. SPL: 102 dB @ 1m ave., 108 dB peak

Nominal Impedance: 8 ohms (in direct/bypass 8Ω setting)

Transformer Taps: 25W, 12.5W, 6.3W @ 70V & 100V;

plus 3.2W @ 70V

Control 16C/T

Components: 165 mm (6.5 in) LF driver;

Frequency Range 1

19 mm (3/4 in) HF driver

: 62 Hz - 20 kHz

Power Capacity (low-Z): 100 W Cont. Program

Sensitivity 2

50 W Cont. Pink Noise

: 91 dB

Coverage 3 : 110˚

Max. SPL: 108 dB @ 1m ave., 116 dB peak

Nominal Impedance: 8 ohms (in direct/bypass 8Ω setting)

Transformer Taps: 30W, 15W, 7.5W @ 70V & 100V;

plus 3.8W @ 70V

Control 18C/T

Components: 200 mm (8 in) LF driver;

Frequency Range 1

25 mm (1 in) HF driver

: 58 Hz - 20 kHz

Power Capacity (low-Z): 180 W Cont. Program

Sensitivity 2

90 W Cont. Pink Noise

: 92 dB

Coverage 3 : 90˚

Max. SPL: 112 dB @ 1m ave., 118 dB peak

Nominal Impedance: 8 ohms (in direct/bypass 8Ω setting)

Transformer Taps: 60W, 30W, 15W @ 70V & 100V;

plus 7.5W @ 70V

C10 MANUAL

Revision B

9

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals