Quick Set-Up - HSU Research

Quick Set-Up - HSU Research
Quick Set-Up Guide for
Dolby Digital Receiver Systems
1. Setting-up the receiver.
On the receiver, go to the SPEAKER SET-UP or BASS MANAGEMENT menu and set the subwoofer to ON or YES. If possible,
set all the speakers to SMALL. Turn the receiver off.
ULS-15 Amplifier Panel
Low Level /Sub Inputs:
Antenna:
Orient for optimal reception.
Usually vertical
position is good.
Wireless Channel Selection:
For Dolby Digital systems, connect the SUBWOOFER OUT to
either of these inputs. For stereo-only systems, you may connect the
left and right channels to both inputs as explained in the manual.
By default, it is set to channel 1.
Unless you have problems with
interference, leave it on channel 1.
2. Placing the subwoofer.
There is no need put the subwoofer between the left and right speakers. Put it in a corner
or near the listening seats if possible.
Wireless Signal Indicator:
LED is on (green) when the wireless receiver and transmitter establishes connection.
Wired/Wireless Switch:
Select “Wireless” if you use the wireless feature.
Otherwise, select “Wired.”
XLR Inputs:
If your processor
has balanced outputs, use these.
Volume Control:
Set this to the second line up from minimum. Use the
subwoofer level control on your controller to fine tune.
If your controller does not have a subwoofer level control, then adjust this to get the desired bass level.
Phase Switch:
Depending on your system and room, the bass in the
crossover region may be smoother if you reverse the
phase of the subwoofer. See the Fine Tuning section of
the manual.
3. Hooking up the subwoofer.
WIRED: Run an interconnect cable from the receiver’s SUBWOOFER or LFE
output to either of the subwoofer’s LOW LEVEL INPUTS. This cable is
available at most electronics and audio stores. Plug the power cord into the
subwoofer, and turn the power switch to “Auto.” Set the wired/wireless switch
on the subwoofer to “Wired.”
Power Indicator:
When the subwoofer is ON, this LED light will be green.
When the subwoofer is in STANDBY mode, it will be red.
Power / Auto-on Switch:
When in the ON position, the subwoofer will stay on at
all times. In AUTO mode, material with bass will quickly turn the subwoofer on. After around 15 - 30 minutes
of inactivity, the subwoofer will automatically go into
STANDBY mode.
WIRELESS: Connect the subwoofer pre-out
to the two inputs on the wireless transmitter
using a splitter. Set the wireless channel on the
transmitter so that it is the same as that on the
subwoofer. Set the wired/wireless switch on
the subwoofer to “Wireless.” Place the transmitter as high as practical, and away from
metal surfaces if possible.
Crossover Defeat Switch:
If you are using a SUBWOOFER or LFE output, you can
disengage the crossover by switching it to OUT. The
crossover should be switched to IN when using high level
inputs or two channel low level inputs.
Crossover Frequency Control:
This low-pass crossover controls what frequencies are
handled by the subwoofer.
ULF Trim:
High Level from Amplifier:
4. Adjusting the volume level.
Set the volume on the subwoofer to the second line up from minimum. Do fine tuning using
the subwoofer level control on your receiver. Adjust to get the desired amount of bass. For
more rigorous level setting, consult the manual.
If your controller does not have low
level outputs (SUBWOOFER, LFE,
or full-range preamp outputs), use
these color coded connectors. Run
speaker wire from your amplifier or
receiver’s speaker terminals to tap
the signal.
Power Input:
This is an IEC socket. Connect
the supplied power cord here. If
your country uses a different
power cord, get one locally.
This compensates for room gain at very low frequencies. Smaller rooms have more boost in the low bass.
Setting this control to 16 Hz gives flat response to 16 Hz
outdoors. Adjust to suit your room.
Voltage Selector Switch:
For 100 - 120V line voltage, set to 120V. For 220 250V, set to 240V.
Removable Fuse Holder:
By pushing in and turning counter-clockwise, you can
remove and replace the fuse. Use only the correctly
rated 5 x 20 mm replacement fuses.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement