(This Page Intentionally Left Blank) RIFMS2

10/01/07 © 2007

Wireless Flush Mount

Intercom

Wall Flush-Mount Design

(Model#: allo

System Features :

• Easily install in drywall for a “Built-in” look. This brand new design features extended, through-wall technology, easily covering the largest home and business locations.

• “C” Batteries operate the unit for up to

3 years.

• Multi-Channel with digital secure connection.

• Unlimited number of units can operate in a dwelling, without mixing with the next-door dwelling.

• Network wide conference mode

The Wireless Flush Mount

Intercom features an amazing 1000’ range, and allows multiple simultaneous conversations, using a 900

MHz secure digital radio link.

For privacy, your intercoms form an exclusive network, and respond only to other intercoms in your network.

Even conversations within your network are secure, as intercoms automatically pair up, blocking all other intercoms from listening in.

Since this intercom system requires no connection to wall power, it is perfect for the do-it-yourself installer.

Please read the instructions carefully.

Note: This unit is recommended for indoor use only.

FCC STATEMENT

This device complies with FCC part 15 rules. It may not cause harmful interference with other devices, and must accept interference from other devices.

FCC ID: JLFTRX

S

etting Up the Intercom

Installation

Choose a wall location that is free of beams and other obstructions inside the wall. Mount the intercom at a convenient height for easy use, typically shoulder height.

Cut a hole in the wall measuring 6 1/8” wide by 4 1/2” high. Insert each of the four screws through a corner of the frame and into a plastic fastener. Screw in only about 1/4” into each plastic fastener - do not tighten.

Place the frame in the hole. With a large screwdriver, tighten the screws until the selfaligning fasteners rotate and tighten to firmly hold the frame in place.

Install four ‘C’ batteries in the

Intercom’s battery pack (the LEDs will illuminate). Clip this unit into the frame by inserting the top section first and then the lower half (as shown in the picture).

This unit is now ready to be taught to other intercoms in the network.

Creating an Intercom Network with

Wall Mount and/or Portable Units.

The Intercom units must be taught to each other to form an intercom network. The Wall

Mount unit is fully compatible with other Wall

Mount Intercom units, as well as the Portable

Intercom units.

To create a new network of intercoms, place each Wall Mount Intercom in Learn mode by holding down both buttons for 3 seconds. The

LEDs will flash rapidly. Within 10 seconds, put any other Wall Mount intercom units in learn mode by holding down the same two buttons

(or single button for the portable unit). Each intercom will produce a tone as it joins the network. Note: One unit may produce a different tone. This is normal.

To add an additional intercom unit to an existing network, put both the new intercom and one of the networked intercoms in learn mode by pushing both buttons on each unit for 3 seconds. The new unit will join the network.

Channel Selection

The default channel for the intercom is the

Paging Channel. All four channel lights will flash in sequence. Press the

CHANNEL button to set an intercom unit to one of four secure channels or the paging channel.

While on a channel, you can only be heard by other units set to the same channel or the paging channel.

Using the Intercom

To talk, hold down the TALK button.

Every intercom unit in the network on the same channel will receive the signal.

Release the TALK button when you are finished talking. When someone responds to you within 10-15 seconds by holding down the TALK button on a different intercom unit, a secure connection is created. Other units will not receive the signal.

Adjusting the speaker volume

The volume can be adjusted by holding down the TALK button and repeatedly pressing the CHANNEL button to cycle through three volume levels.

Conference Mode

All Intercoms must be set on the same channel or the paging channel to participate in the Conference.

To place Intercoms in the Conference

Mode, slide dipswitch #3 (sw3) UP on all

Wall Mount intercoms and dipswitch #2

Up on Portable units in the network.

Troubleshooting and Frequently Asked Questions

Nothing Happens. The Intercom Does Not Function

It is normal for the lights to go out if the Wall Mount Intercom has been inactive for five minutes. The lights should illuminate again after a button is pressed or a signal is received. If the unit does not operate, check the batteries. Normally, the CHANNEL lights should flash, showing the channel that the unit is set to. If the units have power and are not working, they may need to form a network. Press the LEARN buttons on the units that need to be introduced and they will beep in response. You may need to clear their memory (see below), AND THEN teach them.

If the units are not on the same channel, press the CHANNEL button until both units are on the same channel or in Paging mode, with all channel lights illuminated.

The Intercom is Not Getting the Expected Transmission Range

Trees, metal, electrical wiring or other electrical devices directly between units can limit the range, as can having it mounted within is few inches of electrical wiring.

There is a Double Beep every Ten Minutes

The intercom is indicating that the batteries are low and need to be replaced.

How do I Clear the Intercom’s Memory to Remove it from a Network

Press and hold both buttons for 20 seconds. A tone will indicate that the unit has cleared its memory and you can re-teach it to a new intercom. If an intercom signals, while the buttons are depressed, the procedure will have to be repeated.

I hear Static and Feedback through the Intercom

The intercom is probably too close to another intercom. Once the intercom is installed in the desired location, it will operate normally. If a cordless phone, cell phone, or other radio device is too close to the intercom, it can generate static or limit the range.

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

If you have installation or operation questions, please see above, or check out the manufacturer’s web page at www.chamberlain-DIY.com. You can receive free technical assistance by calling 800.528.9131.

Warranty:

This product is warranted to be free of defects for the period of One Year from the date of purchase. The warranty

covers parts, labor, and return shipping to you, but not all accessories. Chamberlain will repair or replace any defective product at our discretion. Warranty does not cover misuse or damage other than due to normal operating conditions. If you need to send the system in for repair, contact Chamberlain for a Return Goods Authorization. Packages without a Return Goods Authorization number will be rejected.