advertisement
ENGLISH
KW-R925BTS / KW-R920BTS
CD RECEIVER
INSTRUCTION MANUAL
For customer Use:
Enter below the Model No. and Serial No. which are located on the top or bottom of the cabinet. Retain this information for future reference.
Model No.
Serial No.
B5A-0831-00 [K]
Data Size:
Book Size:
B6L (182 mm x 128 mm)
B6L (182 mm x 128 mm)
CONTENTS
BEFORE USE 2
BASICS 3
GETTING STARTED
1 Cancel the demonstration
2 Set the clock
3 Set the basic settings
4
RADIO 5
CD / USB / iPod / ANDROID 7
Pandora® 9 iHeartRadio® 10
SiriusXM® Radio 11
BLUETOOTH® 14
AUX 20
AUDIO SETTINGS
DISPLAY SETTINGS
20
24
REFERENCES 26
Maintenance
More information
TROUBLESHOOTING 28
SPECIFICATIONS 30
INSTALLATION /
CONNECTION 32
BEFORE USE
IMPORTANT
• To ensure proper use, please read through this manual before using this product. It is especially important that you read and observe Warning and Caution in this manual.
• Please keep the manual in a safe and accessible place for future reference.
Warning
Do not operate any function that takes your attention away from safe driving.
Caution
Volume setting:
• Adjust the volume so that you can hear sounds outside the car to prevent accidents.
• Lower the volume before playing digital sources to avoid damaging the speakers by the sudden increase of the output level.
General:
• Avoid using the external device if it might hinder safe driving.
• Make sure all important data has been backed up. We shall bear no responsibility for any loss of recorded data.
• Never put or leave any metallic objects (such as coins or metal tools) inside the unit to prevent a short circuit.
• If a disc error occurs due to condensation on the laser lens, eject the disc and wait for the moisture to evaporate.
Remote control (RM-RK52):
• Do not leave the remote control in hot places such as on the dashboard.
• The Lithium battery is in danger of explosion if replaced incorrectly. Replace it only with the same or equivalent type.
• The battery pack or batteries shall not be exposed to excessive heat such as sunshine, fire or the like.
• Keep the battery out of reach of children and in its original packaging when not in used. Dispose of used batteries promptly. If swallowed, contact a physician immediately.
How to read this manual
• Operations are explained mainly using buttons on the faceplate of KW-R925BTS.
• English indications are used for the purpose of explanation. You can select the display language from the menu. ( 5)
• [XX] indicates the selected items.
• ( XX) indicates references are available on the stated page.
2
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BASICS
Faceplate
Loading slot Display window
How to reset
Remote control (RM-RK52)
Remote sensor (Do not expose to bright sunlight.)
T I ST
Press twice within
5 seconds.
Pull out the insulation sheet when using for the first time.
How to replace the battery
Volume knob
KW-R925BTS:
USB cable from the rear of the unit
To
Turn on the power
Adjust the volume
Select a source
Change the display information
On the faceplate
Press .
• Press and hold to turn off the power.
Turn the volume knob.
Press the volume knob to mute the sound or pause playback.
• Press again to cancel.
• Press
• Press
Press
repeatedly.
, then turn the volume knob within 2 seconds.
repeatedly. ( 26)
On the remote control
( Not available )
Press or .
Press to mute the sound or pause playback.
• Press again to cancel.
Press SOURCE repeatedly.
( Not available )
ENGLISH
3
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
GETTING STARTED
3
Set the basic settings
1
Press and hold .
2 Turn the volume knob to select an item (see the following table), then press the knob.
3
Repeat step
2
until the desired item is selected or activated.
4
Press to exit.
To return to the previous setting item, press .
1
Cancel the demonstration
When you turn on the power for the first time (or [FACTORY RST] is set to
[YES]), the display shows: “CANCEL DEMO” “PRESS” “VOLUME KNOB”
1
Press the volume knob.
[YES] is selected for the initial setup.
2 Press the volume knob again.
2
Set the clock
1
Press and hold .
2 Turn the volume knob to select [CLOCK], then press the knob.
3 Turn the volume knob to select [CLOCK SET], then press the knob.
4
Turn the volume knob to make the settings, then press the knob.
Day Hour Minute
5 Turn the volume knob to select [24H/ 12H], then press the knob.
6 Turn the volume knob to select [12 HOUR] or [24 HOUR], then press the knob.
7
Press to exit.
To return to the previous setting item, press .
Default: XX
SETTINGS
BEEP
(Not applicable when 3-way crossover is selected.)
ON: Activates the keypress tone. ; OFF: Deactivates.
SRC SELECT
AM * ON: Enables AM in source selection. ; OFF: Disables.
PANDORA * ON: Enables PANDORA/PANDORA-F/PANDORA-R in source selection. ;
OFF: Disables.
IHEART *
AUX *
ON: Enables IHEARTRADIO/IHEART FRONT/IHEART REAR in source selection. ;
OFF: Disables.
ON: Enables AUX in source selection. ; OFF: Disables.
F/W UPDATE
SYSTEM
F/W xxxx
YES: Starts upgrading the firmware. ; NO: Cancels (upgrading is not activated).
FACTORY RST
YES: Resets the settings to default (except the stored station). ; NO: Cancels.
* Not displayed when the corresponding source is selected.
4
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
GETTING STARTED
CLOCK
CLOCK SYNC
AUTO: The clock time is automatically set using the Clock Time (CT) data in FM Radio Broadcast
Data System signal. ; OFF: Cancels.
CLOCK DISP
ON: The clock time is shown on the display even when the unit is turned off. ; OFF: Cancels.
ENGLISH
ESPANOL
Select the display language for menu and music information if applicable.
By default, ENGLISH is selected.
RADIO
“ST” lights up when receiving an FM stereo broadcast with sufficient signal strength.
Search for a station
1
Press
2 Press
(or)
Press and hold
repeatedly to select FM or AM.
(or press on RM-RK52) to search for a station automatically.
(or press and hold on RM-RK52) until “M” flashes, then press repeatedly to search for a station manually.
Settings in memory
You can store up to 18 stations for FM and 6 stations for AM.
Store a station
While listening to a station....
Press and hold one of the number buttons (1 to 6).
(or)
1
Press and hold the volume knob until “PRESET MODE” flashes.
2 Turn the volume knob to select a preset number, then press the knob.
The preset number flashes and “MEMORY” appears.
ENGLISH
5
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
RADIO
Select a stored station
Press
(or)
or one of the number buttons (1 to 6).
1
Press .
2 Turn the volume knob to select a preset number, then press the knob to confirm.
Other settings
1
Press and hold .
2
Turn the volume knob to select [TUNER], then press the knob.
3 Turn the volume knob to select an item (see the following table), then press the knob.
4
Repeat step
3
until the desired item is selected/activated or follow
5 the instructions stated on the selected item.
Press to exit.
To return to the previous setting item, press .
RADIO TIMER
Default: XX
Turns on the radio at a specific time regardless of the current source.
1 ONCE/ DAILY/ WEEKLY/ OFF: Select how often the timer will be turned on.
2 FM/ AM/ SIRIUS XM *
1
: Select the source.
3 01 to 18 (for FM/ SIRIUS XM)/ 01 to 06 (for AM): Select the preset station.
4 Set the activation day *
2
and time.
“M” lights up when complete.
Radio Timer will not activate for the following cases.
• The unit is turned off.
• [OFF] is selected for [AM] in [SRC SELECT] after Radio Timer for AM is selected. ( 4)
SSM
IF BAND
MONO *
3
SSM 01 – 06 / SSM 07 – 12 / SSM 13 – 18: Automatically presets up to 18 stations for FM. “SSM” stops flashing when the first 6 stations are stored. Select SSM 07 – 12 / SSM 13 – 18 to store the following 12 stations.
AUTO: Increases the tuner selectivity to reduce interference noises from adjacent FM stations. (Stereo effect may be lost.) ; WIDE: Subjects to interference noises from adjacent FM stations, but sound quality will not be degraded and the stereo effect will remain.
ON: Improves the FM reception, but the stereo effect will be lost. ;
OFF: Cancels.
AREA
AREA US: For North/Central/South America, AM/FM intervals:
10 kHz/200 kHz. ; AREA SA: For some South American countries, AM/
FM intervals: 10 kHz/50 kHz. ; AREA EU: For any other areas, AM/FM intervals: 9 kHz/50 kHz.
PTY SEARCH *
3
Select a PTY code (see below).
If there is a station broadcasting a program of the same PTY code as you have selected, that station is tuned in.
PTY code: NEWS, INFORM (information), SPORTS, TALK, ROCK, CLS ROCK (classic rock), ADLT HIT (adult hits), SOFT RCK (softrock), TOP 40, COUNTRY, OLDIES, SOFT,
NOSTALGA (nostalgia), JAZZ, CLASSICL (classical), R & B (rhythm and blues),
SOFT R&B (soft rhythm and blues), LANGUAGE, REL MUSC (religious music),
REL TALK (religious talk), PERSNLTY (personality), PUBLIC, COLLEGE, HABL ESP
(Spanish talk), MUSC ESP (Spanish music), HIP HOP, WEATHER
*
1 Selectable only when SiriusXM Vehicle Tuner is connected.
* 2
Selectable only when [ONCE] or [WEEKLY] is selected in step
1
.
* 3
Only for FM source.
6
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
CD / USB / iPod / ANDROID
Start playback
The source changes automatically and playback starts.
CD
Eject disc Label side
Selectable source:
• KW-R925BTS: CD/ USB FRONT/
USB REAR/ IPOD FRONT/ IPOD
REAR/ ANDROID-F/ ANDROID-R
• KW-R920BTS: CD/ USB/
USB-IPOD/ ANDROID
USB input terminal
USB
USB 2.0 cable*
1
(commercially available)
KW-R925BTS:
You can also connect to the USB cable from the rear of the unit.
iPod/iPhone
(Accessory of the iPod/iPhone)*
1
ANDROID
*
2
Micro USB 2.0 cable*
1
(commercially available)
To On the faceplate
Reverse / Fast-forward*
3
Press and hold
Select a track/file
Select a folder*
4
Repeat play* 5
Press
Press
Press
.
.
repeatedly.
.
Random play* 5
On the remote control
Press and hold
Press .
Press .
.
TRACK RPT/ FOLDER RPT/ ALL RPT : MP3/WMA/AAC/WAV/FLAC file
ONE RPT/ ALL RPT/ RPT OFF : iPod or ANDROID
Press repeatedly.
SONG RND/ ALL RND/ RND OFF : iPod or ANDROID
* 1
Do not leave the cable inside the car when not using.
* 2
When connecting an Android device, “Press [VIEW] to install JVC MUSIC PLAY APP” is shown. Follow the instructions to install the application. You can also install the latest version of JVC MUSIC PLAY application on your Android device before connecting.
( 26)
* 3
For ANDROID: Applicable only when [AUTO MODE] is selected. ( 8)
* 4
For CD: Only for MP3/WMA/AAC files. This does not work for iPod/ ANDROID.
* 5
For iPod/ ANDROID: Applicable only when [HEAD MODE]/ [AUTO MODE] is selected. ( 8)
ENGLISH
7
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
CD / USB / iPod / ANDROID
Select control mode
While in IPOD FRONT/ IPOD REAR/ USB-IPOD source, press
repeatedly.
HEAD MODE: Control iPod from this unit.
IPHONE MODE: Control iPod using the iPod itself. However, you can still play/pause or file skip from this unit.
While in ANDROID/ ANDROID-F/ ANDROID-R source, press
repeatedly.
AUTO MODE: Control Android device from this unit via JVC MUSIC PLAY application installed in the Android device.
AUDIO MODE: Control Android device using the Android device itself via other media player applications installed in the Android device. However, you can still play/pause or file skip from this unit.
Select music drive
Press repeatedly.
Stored songs in the following drive will be played back.
• Selected internal or external memory of a smartphone (Mass Storage
Class).
• Selected drive of a multiple drives device.
Select a file from a folder/list
1 Press .
2 Turn the volume knob to select a folder/list, then press the knob.
3
Turn the volume knob to select a file, then press the knob.
Quick Search
If you have many files, you can search through them quickly.
Turn the volume knob quickly to browse through the list quickly.
– Not applicable for iPod.
Alphabet search (applicable only for iPod):
You can search for a file according to the first character.
Press or turn the volume knob quickly to select the desired character (A to Z/ 0 to 9/ OTHERS).
– Select “OTHERS” if the first character is other than A to Z, 0 to 9.
• To return to the previous setting item, press
• To cancel, press and hold .
.
• For iPod, applicable only when [HEAD MODE] is selected.
• For ANDROID, applicable only when [AUTO MODE] is selected.
8
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Pandora®
Preparation:
Install the latest version of the Pandora application on your device
(iPhone/ iPod touch), then create an account and log in to Pandora.
• Select [ON] for [PANDORA] in [SRC SELECT]. ( 4)
Start listening
1 Open the Pandora application on your device.
2 Connect your device to the USB input terminal.
USB input terminal
Create and save a new station
1
Press .
2
Turn the volume knob to select [NEW STATION], then press the knob.
3 Turn the volume knob to select [FROM TRACK] or [FROM ARTIST], then press the knob.
A new station is created based on the current song or artist.
4
Press and hold one of the number buttons (1 to 6) to store.
To select a stored station, press one of the number buttons (1 to 6).
and / or (Accessory of the iPod/iPhone)*
1
To On the faceplate
Playback / pause Press the volume knob.
Skip a track
Thumbs up or
thumbs down* 2
Press T.
Press .
*
1
Do not leave the cable inside the car when not using.
* 2
If thumbs down is selected, the current track is skipped.
Search for a registered station
1 Press .
2
Turn the volume knob to select an item, then press the knob.
[BY DATE]: According to the registered date.
[A-Z]: Alphabetical order.
3 Turn the volume knob to select the desired station, then press the knob.
To cancel, press and hold .
3
KW-R925BTS:
You can also connect to the USB cable from the rear of the unit.
Press
PANDORA-R.
repeatedly to select PANDORA/ PANDORA-F/
On the remote control
Press .
Press I.
Press .
Bookmark current song information
Press and hold the volume knob.
“BOOKMARKED” appears and the information is stored to your device.
The bookmark is available on your Pandora account but not on this unit.
ENGLISH
9
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
iHeartRadio®
Preparation:
Install the latest version of iHeartAuto application on your device
(iPhone/ iPod touch), then create an account and log in to iHeartRadio.
• Select [ON] for [IHEART] in [SRC SELECT]. ( 4)
Start listening
1
Open the iHeartAuto application on your device.
2
Connect your device to the USB input terminal.
USB input terminal and / or
(Accessory of the iPod/iPhone)*
KW-R925BTS:
You can also connect to the USB cable from the rear of the unit.
3 Press repeatedly to select IHEARTRADIO/
IHEART FRONT/ IHEART REAR.
* Do not leave the cable inside the car when not using.
To
Playback / pause
Skip a track for custom station
Thumbs up or thumbs down
Create a new/ custom station
Scan for live station
On the faceplate
Press the volume knob.
Press T.
Press .
Press and hold the volume knob.
1 Press 1 to start scanning.
2
Press the volume knob to listen to the station.
On the remote control
Press .
Press I.
Press .
( Not available )
( Not available )
Search and store a station
1 Press .
2 Turn the volume knob to select a category, then press the knob.
3
Turn the volume knob to select the desired station, then press the knob.
When a city list appears, you can search cities in alphabetical order by turning the volume knob quickly.
To cancel, press and hold .
• To store a station: Press and hold one of the number buttons (2 to 6).
• To select a stored station: Press one of the number buttons (2 to 6).
10
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
SiriusXM® Radio
Only SiriusXM® brings you more of what you love to listen to, all in one place. Get over 140 channels, including commercial-free music plus the best sports, news, talk, comedy and entertainment. Welcome to the world of satellite radio. A SiriusXM Vehicle Tuner and
Subscription are required.
Preparation:
1
Connect the optional SiriusXM Vehicle Tuner
(commercially available).
Antenna
Start listening
1 Press
2
Press
.
repeatedly to select SIRIUS XM.
“ ” lights up.
3
Turn the volume knob to select a CATEGORY, then press the knob.
4 Turn the volume knob to select a category from the list, then press the knob.
If “ALL CHANNEL” is selected, all the available channels will be shown.
5
Turn the volume knob to select a channel, then press the knob.
(or)
Press to search for a channel manually.
• Pressing and holding changes the channel rapidly.
If a locked channel or a mature channel is selected, a pass code input screen appears.
Enter the pass code to receive the channel. ( 13)
Expansion port on the rear panel
SiriusXM
Vehicle Tuner
2
Check your Radio ID for activation.
The SiriusXM Radio ID is required for activation and can be found by tuning to Channel 0 as well as on the label found on the SiriusXM Connect tuner and its packaging.
The Radio ID does not include the letters I, O, S or F.
3
Press repeatedly to select SIRIUS XM to start updating.
Store a channel
You can store up to 18 channels.
To
Store a channel
Select a stored channel
Do this
Press and hold one of the number buttons (1 to 6).
1
Press and hold the volume knob until “PRESET MODE” flashes.
2 Turn the volume knob to select a preset number, then press the knob.
The preset number flashes and “MEMORY” appears.
Press one of the number buttons (1 to 6).
1
Press .
2
Turn the volume knob to select PRESET, then press the knob.
3 Turn the volume knob to select a preset number, then press the knob.
Press on RM-RK52.
ENGLISH
11
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
SiriusXM® Radio
SiriusXM Replay™
1 Press the volume knob.
“ ” lights up and the unit memorizes this paused position.
2
Press the volume knob to start Replay.
Replay starts from the paused position in step
1
.
During Replay...
To
Playback / pause
On the faceplate
Press the volume knob.
On the remote control
Press
Skip the current song backward/forward
Rewind /
Fast-forward
Go to Live and exit
Replay
Press .
Press .
Press and hold
.
Press and hold
Press and hold the volume knob.
1 Press .
2 Turn the volume knob to select LIVE, then press the knob.
.
When you select a SmartFavorites channel, you can rewind and replay up to 30 minutes of any of the missed news, talk, sports or music content.
• Playback starts from the beginning of the song if [TUNE START] is set to
[ON] ( 13) for most music channels stored as a SmartFavorite.
To
Select a stored
SmartFavorite channel
Cancel
SmartFavorites channels
Reassign
SmartFavorites channels
On the faceplate
Press one of the number buttons (1 to 6).
1
Press .
2 Turn the volume knob to select a preset number, then press the knob to confirm.
1
Press
.
2
Turn the volume knob to select PRESET, then press the knob.
3 Turn the volume knob to select a preset number, then press and hold the knob.
“
*
” are removed from the last character.
Repeat steps 1 to 3 of cancelling SmartFavorites channels.
“
*
” appears at the last character.
SmartFavorites and TuneStart™
User preset channels are initially assigned as the SmartFavorites channels.
SmartFavorite channel is available with SXV200 or later SiriusXM tuner models. The SiriusXM Vehicle Tuner automatically buffers the broadcast audio content of the SmartFavorites channels in the background.
• Using SXV200: This unit can assign a maximum of 6 SmartFavorites channels. If you try to assign the 7th channel, an error beep tone will be heard. Initially, preset channels 1 to 6 are assigned as SmartFavorites.
Using SiriusXM tuner models later than SXV200: This unit can assign a maximum of 18 SmartFavorites channels. Initially, all preset channels are assigned as SmartFavorites.
*
” appears at the last character of the channel name for the
SmartFavorites channels.
12
TuneScan™
You can get a short preview of the songs that you have missed on each of your SmartFavorite music channels or currently tuned music channel.
1
Press
.
2 Turn the volume knob to select TUNE SCAN, then press the knob.
Scanning start for the first 6 seconds of the recorded music contents.
• To listen to the current song, press the volume knob to stop scanning.
The unit continues playing the current song.
• To select the previous/next song, press .
• To cancel scanning, press and hold the volume knob. Playback returns to the channel before you entered TuneScan.
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
SiriusXM® Radio
SiriusXM settings
1 Press and hold .
2 Turn the volume knob to select [SIRIUS XM], then press the knob.
3
Turn the volume knob to select an item (see the following table), then press the knob.
4 Repeat step 3 until the desired item is selected/activated or follow the instructions stated on the selected item.
5
Press to exit.
To return to the previous setting item, press .
Default: XX
CH LOCK
CODE SET
LOCK SET
CH EDIT* 1
CH CLEAR*
1
To unlock settings:
1 Turn the volume knob to select a number.
2 Press to move to the entry position.
3 Repeat steps 1 and 2 to enter the current pass code.
(Initial pass code is 0000.)
4 Press the volume knob to confirm.
1 Press the volume knob to enter [NEW CODE].
2 Turn the volume knob to select a number.
3 Press to move to the entry position.
4 Repeat steps 2 and 3 to enter a new 4-digit pass code.
5 Press the volume knob to confirm.
6 Repeat steps 2 to 5 to reconfirm the pass code.
• Make a note of the new pass code to enter channel lock settings for next time.
MATURE CH: Selects the SiriusXM-defined lock setting. ; USER
DEFINED: Selects the individual channels the user wants to lock. ; OFF: Cancels.
1 Turn the volume knob to select a category, then press the knob.
2 Turn the volume knob to select a channel you want to lock, then press the knob.
“L” appears in front of the channel number.
3 Press and hold to exit.
YES: Clears all the locked channels. ; NO: Cancels.
TUNE START*
2
ON: All qualified music channels in the Smart Favorites will start playback from the beginning of the song. ; OFF: Cancels.
SIGNAL LVL
BUF USAGE
NO SIGNAL/ WEAK/ GOOD/ STRONG: Shows the strength of the current received signal.
0% — 100% (0): Shows the memory usage for Replay buffer.
SXM RESET
YES: Resets stored channel and lock setting to default. ;
NO: Cancels.
* 1
Displayed only when [USER DEFINED] is selected.
*
2
Available only if the connected SiriusXM Vehicle Tuner is SXV200 or later that supports SmartFavorites.
ENGLISH
13
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
BLUETOOTH — Connection
Supported Bluetooth profiles
– Hands-Free Profile (HFP)
– Advanced Audio Distribution Profile (A2DP)
– Audio/Video Remote Control Profile (AVRCP)
– Serial Port Profile (SPP)
– Phonebook Access Profile (PBAP)
Supported Bluetooth codecs
– Sub Band Codec (SBC)
– Advanced Audio Coding (AAC)
Connect the microphone
Rear panel
MIC (Microphone input terminal)
Microphone
(supplied)
Adjust the microphone angle
Secure using cord clamps
(not supplied) if necessary.
Pair and connect a Bluetooth device for the first time
1 Press to turn on the unit.
2 Search and select “JVC UNIT” on the Bluetooth device.
“BT PAIRING” flashes on the display.
• For some Bluetooth devices, you may need to enter the Personal Identification Number
(PIN) code immediately after searching.
3 Perform (A) or (B) depending on what scrolls on the display.
For some Bluetooth devices, pairing sequence may vary from the steps described below.
(A) “[Device Name]” “XXXXXX” “VOL – YES” “BACK – NO”
“XXXXXX” is a 6-digit passkey randomly generated during each pairing.
Ensure that the passkey which appears on the unit and Bluetooth device is the same.
Press the volume knob to confirm the passkey.
Operate the Bluetooth device to confirm the passkey.
(B) “[Device Name]” “VOL – YES” “BACK – NO”
Press the volume knob to start pairing.
• If “PAIRING” “PIN 0000” scrolls on the display, enter the PIN code “0000” into the
Bluetooth device.
You can change to a desired PIN code before pairing. ( 18)
• If only “PAIRING” appears, operate the Bluetooth device to confirm pairing.
“PAIRING COMPLETED” appears when pairing is completed and “ ” will light up when the
Bluetooth connection is established.
ST
* Functionality depends on the type of the phone used.
Lights up to show the battery strength and signal strength.*
• This unit supports Secure Simple Pairing (SSP).
• Up to 10 devices can be registered (paired) in total.
• Once the pairing is completed, the Bluetooth device will remain registered in the unit even if you reset the unit. To delete the paired device, 18, [DELETE PAIR].
• A maximum of two Bluetooth phones and one Bluetooth audio device can be connected at any time.
• Some Bluetooth devices may not automatically connect to the unit after pairing. Connect the device to the unit manually.
• Refer to the instruction manual of the Bluetooth device for more information.
14
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
Auto Pairing
When you connect the iPhone/ iPod touch/
Android device to the USB input terminal, pairing request (via Bluetooth) is automatically activated.
Press the volume knob to pair once you have confirmed the device name.
Automatic pairing request is activated only if:
– Bluetooth function of the connected device is turned on.
– [AUTO CNNT] is set to [ON]. ( 18)
– JVC MUSIC PLAY application is installed on the Android device ( 7) and [AUTO MODE] is selected ( 8).
BLUETOOTH — Mobile phone
Receive a call
When there is an incoming call:
• The buttons will blink in the color you have selected in [RING COLOR]. ( 16)
• The unit answers the call automatically if [AUTO ANSWER] is set to a selected time. ( 16)
During a call:
• The buttons stop blinking and illuminate in the color you have selected in [RING COLOR]. ( 16)
• If you turn off the unit, the Bluetooth connection is disconnected.
To
First incoming call...
Answer a call
Reject a call
End a call
On the faceplate
Press or the volume knob.
Press and hold volume knob.
or the
Press and hold volume knob.
or the
On the remote control
Press
Press and hold
.
Press and hold
.
.
ENGLISH
15
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
To On the faceplate
While talking on the first incoming call...
Answer another incoming call and hold the current call
Press knob.
Reject another incoming call
or the volume
Press and hold the volume knob.
or
While having two active calls...
End current call and activate held call
Press and hold the volume knob.
Swap between the current call and held call
Adjust the phone volume
[00] to [35] (Default: [15])
Press .
or
Turn the volume knob during a call.
• This adjustment will not affect the volume of the other sources.
Switch between hands-free and private talk modes
Press during a call.
• Operations may vary according to the connected Bluetooth device.
On the remote control
( Not available )
( Not available )
Press and hold
.
( Not available )
( Not available )
( Not available )
Default: XX
MIC LEVEL
NOISE RDCT
–10 — +10 (–4): The sensitivity of the microphone increases as the number increased.
–5 — +5 (0): Adjust the noise reduction level until the least noise is being heard during a phone conversation.
ECHO CANCEL
–5 — +5 (0): Adjust the echo cancellation delay time until the least echo is being heard during a phone conversation.
Make the settings for receiving a call
1 Press to enter Bluetooth mode.
2 Turn the volume knob to select an item (see the following table), then press the knob.
3
Repeat step
2
until the desired item is selected or activated.
To return to the previous setting item, press .
Default: XX
SETTINGS
AUTO ANSWER
01 SEC — 30 SEC: The unit answers incoming call automatically in the selected time (in seconds). ;
OFF: Cancels.
RING COLOR
COLOR 01 — COLOR 49 (COLOR 08): Selects the notification light color for the buttons when there is an incoming call and during a call. ; OFF : Cancels.
Improve the voice quality
While talking on the phone....
1
Press and hold .
2
Turn the volume knob to select an item (see the following table), then press the knob.
3 Repeat step 2 until the desired item is selected or activated.
4
Press to exit.
To return to the previous setting item, press .
16
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
Make a call
You can make a call from the call history, phonebook, or dialing the number.
Call by voice is also possible if your mobile phone has the feature.
1
Press to enter Bluetooth mode.
2
Turn the volume knob to select an item (see the following table), then press the knob.
3 Repeat step 2 until the desired item is selected/activated or follow the instructions stated on the selected item.
To return to the previous setting item, press .
Make a call using voice recognition
1 Press and hold to activate the connected phone.
2
Speak the name of the contact you want to call or the voice command to control the phone functions.
• Supported Voice Recognition features vary for each phone. Refer to the instruction manual of the connected phone for details.
• This unit also supports the intelligent personal assistant function of iPhone.
RECENT CALL
(Applicable only if the phone supports PBAP)
1 Press the volume knob to select a name or a phone number.
• “<” indicates call received, “>“ indicates call made, “M” indicates call missed.
• “NO HISTORY” appears if there is no recorded call history or call number.
2 Press the volume knob to call.
PHONEBOOK
(Applicable only if the phone supports PBAP)
1 Press to select the desired letter (A to Z, 0 to 9, and OTHERS).
• “OTHERS” appears if the first character is other than A to Z, 0 to 9.
2 Turn the volume knob to select a name, then press the knob.
3 Turn the volume knob to select a phone number, then press the knob to call.
• The phonebook of the connected phone is automatically transferred to the unit when pairing.
• This unit can display only non-accent letters. (Accent letters such as “Ú” is showns as “U”.)
DIAL NUMBER
1 Turn the volume knob to select a number (0 to 9) or character ( , #, +).
2 Press to move the entry position.
1
and
2
until you finish entering the phone number.
3 Press the volume knob to call.
VOICE
Speak the name of the contact you want to call or the voice command to control the phone functions. ( Make a call using voice recognition)
Settings in memory
Store a contact in memory
You can store up to 6 contacts into the number buttons (1 to 6).
1
Press
to enter Bluetooth mode.
2 Turn the volume knob to select [RECENT CALL], [PHONEBOOK], or
[DIAL NUMBER], then press the knob.
3
Turn the volume knob to select a contact or enter a phone number.
If a contact is selected, press the volume knob to show the phone number.
4
Press and hold one of the number buttons (1 to 6).
“MEMORY P(selected preset number)” appears when the contact is stored.
To erase a contact from the preset memory, select [DIAL NUMBER] in step
2
and store a blank number.
Make a call from memory
1
Press to enter Bluetooth mode.
2
Press one of the number buttons (1 to 6).
3 Press the volume knob to call.
“NO PRESET” appears if there is no contacts stored.
ENGLISH
17
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
Bluetooth mode settings
1
Press and hold .
2
Turn the volume knob to select [BLUETOOTH], then press the knob.
3
Turn the volume knob to select an item (see the following table), then press the knob.
4
Repeat step
3
until the desired item is selected/activated or follow the instructions stated on the selected item.
5
Press to exit.
To return to the previous setting item, press .
Default: XX
PHONE*
1
AUDIO*
1
Selects the phone or audio device to connect or disconnect.
“ ” appears in front of the device name when connected.
APPLICATION* 1 Shows the connected phone name using the JVC Smart Music Control * 2 app.
“ ” appears in front of the device name when connected.
DELETE PAIR
1 Turn the volume knob to select a device to delete, then press the knob.
2 Turn the volume knob to select [YES] or [NO], then press the knob.
SET PINCODE
(0000)
Changes the PIN code (up to 6 digits).
1 Turn the volume knob to select a number.
2 Press
to move the entry position.
1
and
2
until you finish entering the PIN code.
3 Press the volume knob to confirm.
AUTO CNNCT
AUTO PAIR
INITIALIZE
ON: The unit automatically reconnect when the last connected Bluetooth device is within range. ; OFF: Cancels.
ON: The unit automatically pair supported Bluetooth device (iPhone/ iPod touch/
Android device) when it is connected through USB input terminal. Depending on the operating system of the connected device, this function may not work. ; OFF: Cancels.
YES: Initializes all the Bluetooth settings (including stored pairing, phonebook, and etc.). ; NO: Cancels.
INFORMATION
MY BT NAME: Displays the unit name (JVC UNIT). ;
MY ADDRESS: Shows address of this unit.
*
1 You can only connect a maximum of two Bluetooth phones and one Bluetooth audio device at any time.
*
2 JVC Smart Music Control is designed to view JVC car receiver status and perform simple control operations on Android smart phones.
Bluetooth compatibility check mode
You can check the connectivity of the supported profile between the Bluetooth device and the unit.
• Make sure there is no Bluetooth device paired.
1
Press and hold .
“BLUETOOTH” “CHECK MODE” appears. “SEARCH NOW
USING PHONE” “PIN IS 0000” scrolls on the display.
2
Search and select “JVC UNIT” on the Bluetooth device within 3 minutes.
3 Perform (A), (B) or (C) depending on what appears on the display.
(A) “PAIRING” “XXXXXX” (6-digit passkey): Ensure that the same passkey appears on the unit and Bluetooth device, then operate the Bluetooth device to confirm the passkey.
(B) “PAIRING” “PIN IS 0000”: Enter “0000” on the
Bluetooth device.
(C) “PAIRING”: Operate the Bluetooth device to confirm pairing.
After pairing is successful, “PAIRING OK” “[Device Name]” appears and Bluetooth compatibility check starts.
If “CONNECT NOW USING PHONE” appears, operate the
Bluetooth device to allow phonebook access to continue.
“TESTING” flashes on the display.
The connectivity result flashes on the display.
“PAIRING OK” and/or “H.FREE OK”*
1
and/or “A.STREAM OK”*
2 and/or “PBAP OK”*
3
: Compatible
* 1
Compatible with Hands-Free Profile (HFP)
*
2
Compatible with Advanced Audio Distribution Profile (A2DP)
* 3
Compatible with Phonebook Access profile (PBAP)
After 30 seconds, “PAIRING DELETED” appears to indicate that pairing has been deleted, and the unit exits check mode.
• To cancel, press and hold then turn on the power again.
to turn off the power,
18
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
BLUETOOTH®
BLUETOOTH — Audio
Audio player via Bluetooth
1 Press repeatedly to select BT AUDIO (or press SOURCE on RM-RK52).
2 Operate the Bluetooth audio player to start playback.
To
Playback / pause
On the faceplate
Press the volume knob.
On the remote control
Press .
Select group or folder
Reverse / Forward skip
Reverse / Fast-forward
Repeat play
Random play
Press
Press
.
Press and hold
Press repeatedly.
TRACK RPT, ALL RPT, RPT OFF
.
Press repeatedly.
GROUP RND, ALL RND, RND OFF
Refer to “Select a file from a folder/ list” on page 8.
.
Press
Press .
.
Press and hold
( Not available )
( Not available )
Select a file from a folder/ list
( Not available )
Operations and display indications may differ according to their availability on the connected device.
.
Internet radio via Bluetooth
Listen to Pandora
You can listen to Pandora on the Android device via
Bluetooth on this unit.
Preparation:
Select [ON] for [PANDORA] in [SRC SELECT]. ( 4)
1
Open the Pandora application on your device.
2
Connect your Bluetooth audio player via
Bluetooth connection. ( 14)
3 Press repeatedly to select PANDORA.
The source switches and broadcast starts automatically.
You can operate Pandora in the same way as Pandora for iPod/iPhone. ( 9)
Listen to iHeartRadio
You can listen to iHeartRadio on the Android device via Bluetooth on this unit.
Preparation:
Select [ON] for [IHEART] in [SRC SELECT]. ( 4)
1 Open the iHeartAuto application on your smart phone.
2
Connect your smart phone via Bluetooth
connection. ( 14)
3 Press
IHEARTRADIO.
repeatedly to select
The source switches and broadcast starts automatically.
You can operate iHeartRadio in the same way as iHeartRadio for iPod/iPhone. ( 10)
ENGLISH
19
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUX
Use a portable audio player
1
Connect a portable audio player (commercially available).
3.5 mm (1/8") stereo mini plug with “L” shaped connector
(commercially available)
AUDIO SETTINGS
Auxiliary input jack
Portable audio player
2
Select [ON] for [AUX] in [SRC SELECT]. ( 4)
3 Press repeatedly to select AUX.
4
Turn on the portable audio player and start playback.
Use a 3-core plug head stereo mini plug for optimum audio output.
Select a preset equalizer
Press
(or)
Press
repeatedly.
, then turn the volume knob within 5 seconds.
Preset equalizer:
FLAT (default)/ HARD ROCK / POP / HIP HOP / R&B / JAZZ / CLASSICAL / USER
Store your own sound settings
1
Press and hold to enter EASY EQ setting.
2
Turn the volume knob to select an item, then press the knob.
Refer to [EASY EQ] for setting ( 21) and the result is stored to [USER].
• To return to the previous setting item, press
• To exit, press .
.
Other settings
1 Press and hold .
2
Turn the volume knob to select an item ( 21), then press the knob.
3
Repeat step
2
until the desired item is selected/activated or follow the instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press .
20
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO SETTINGS
Default: XX
EQ SETTING
EQ PRESET
Select a preset equalizer suitable to the music genre. (Select [USER] to use the settings made in [EASY EQ] or [PRO EQ].)
FLAT / HARD ROCK / POP / HIP HOP / R&B / JAZZ / CLASSICAL /
USER
EASY EQ
Adjust your own sound settings. The settings are stored to [USER].
• The settings made may affect the current settings of [PRO EQ].
SUB.W SP *
1 * 2
:
SUB.W *
1 * 3
: –50 to +10
00
BASS LVL:
MID LVL:
TRE LVL:
–09 to +09
–09 to +09
–09 to +09
00
00
00)
PRO EQ
Adjust your own sound settings. The settings are stored to [USER].
• The settings made may affect the current settings of [EASY EQ].
62.5HZ
LVL –09 to +09 (00): Adjusts the level to memorize for each source.
(Before making an adjustment, select the source you want to adjust.)
BASS EXT ON: Turns on the extended bass. ; BASS EXT OFF: Cancels.
100HZ / 160HZ / 250HZ / 400HZ / 630HZ / 1KHZ / 1.6KHZ / 2.5KHZ /
4KHZ / 6.3KHZ / 10KHZ / 16kHZ
LVL –09 to +09 (00): (Refer above)
Q FACTOR
Q 1.35/ Q 1.50/ Q 2.00: Adjust the quality factor.
AUDIO
BASS BOOST
+01 — +05: Selects your preferred bass boost level. ; OFF: Cancels.
LOUD
01 / 02: Boosts low or high frequencies to produce a well-balanced sound at low volume. ; OFF: Cancels.
SUB.W LEVEL *
1
SPK-OUT *
2
(Not applicable when 3-way crossover is selected.)
00 to +06 (+03): Adjusts the output level of the subwoofer connected via speaker lead. ( 33)
PRE-OUT *
3
–50 to +10 (00): Adjusts the output level of the subwoofer connected to the lineout terminals (SW or REAR/SW) through an external amplifier. ( 33)
SUB.W *
3
ON / OFF: Turns on or off the subwoofer output.
FADER
BALANCE *
4
VOL ADJUST
(Not applicable when 3-way crossover is selected.)
R15 — F15 (00): Adjusts the front and rear speaker output balance.
L15 — R15 (00): Adjusts the left and right speaker output balance.
–15 — +06 (00): Preset the initial volume level of each source (compared to the FM volume level). Before adjustment, select the source you want to adjust.
AMP GAIN
SPK/PRE OUT
LOW POWER: Limits the maximum volume level to 25. (Select if the maximum power of each speaker is less than 50 W to prevent damaging the speakers.) ;
HIGH POWER: The maximum volume level is 35.
(Not applicable when 3-way crossover is selected.)
Depending on the speaker connection method, select the appropriate setting to get the desired output. ( 22, Speaker output settings)
SPK SIZE
X ' OVER
Depending on the crossover type you have selected (see [X ' OVER TYPE] below), 2-way crossover or 3-way crossover setting items will be shown. ( 23,
Crossover settings)
By default, 2-way crossover type is selected.
X ' OVER TYPE
Caution: Adjust the volume before changing the X ' OVER TYPE to avoid the sudden increase or decrease of the output level.
X ' OVER 2-WAY
(Displayed only when [X ' OVER 3-WAY] is selected)
YES: Selects two way crossover type. ; NO: Cancels.
X ' OVER 3-WAY
(Displayed only when [X ' OVER 2-WAY] is selected)
YES: Selects three way crossover type. ; NO: Cancels.
* 1
Displayed only when [SUB.W] is set to [ON].
* 2
For 2-way crossover: Displayed only when [SPK/PRE OUT] is set to [SUB.W/SUB.W]. ( 22)
* 3
For 2-way crossover: Displayed only when [SPK/PRE OUT] is set to [REAR/SUB.W] or [SUB.W/
SUB.W]. ( 22)
* 4
This adjustment will not affect the subwoofer output.
ENGLISH
21
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO SETTINGS
SND EFFECT
ENHANCE
RESPONSE
SOUND LIFT
VOL LINK EQ
K2
(Not applicable for TUNER source.)
SML/ MED/ LRG: Virtually enhances the sound space. ; OFF: Cancels.
LV1/ LV2/ LV3: Virtually makes the sound more realistic. ; OFF: Cancels.
LV1/ LV2/ LV3: Virtually adjust the sound position heard from the speakers. ; OFF: Cancels.
ON: Boosts the frequency to reduce the noise heard from outside the car or running noise of the tyres. ; OFF: Cancels.
(Not applicable for TUNER source, SIRIUS XM source, AUX source.)
ON: Improve the sound quality of compressed music. ; OFF: Cancels.
Speaker output settings
(Only for X ' OVER 2-WAY)
Select the output setting for the speakers [SPK/PRE OUT], base on the speaker connection method.
Connection via lineout terminals
For connections through an external amplifier. ( 33)
(For KW-R925BTS)
Setting on
[SPK/PRE OUT]
REAR/REAR
(default)
FRONT
Front speakers output
Audio signal through lineout terminal
REAR
Rear speakers output
SW
Subwoofer output
REAR/SUB.W
( Not available ) ( Not available )
SUB.W/SUB.W
Front speakers output
L (left): Subwoofer output
R (right): (Mute)
( Not available )
Subwoofer output
(For KW-R920BTS)
Setting on
[SPK/PRE OUT]
Audio signal through lineout terminal
REAR/REAR
FRONT
Front speakers output
REAR/SUB.W (default) Front speakers output
REAR/SW
Rear speakers output
Subwoofer output
SUB.W/SUB.W
Front speakers output Subwoofer output
Connection via speaker leads
For connections without using an external amplifier. However, with this settings you can also enjoy the subwoofer output. ( 33)
Setting on
[SPK/PRE OUT]
REAR/REAR
REAR/SUB.W
SUB.W/SUB.W
Audio signal through rear speaker lead
L (left) R (right)
Rear speakers output
Rear speakers output
Subwoofer output
Rear speakers output
Rear speakers output
(Mute)
If [SUB.W/SUB.W] is selected:
– [FRQ 120HZ] is selected in [SUB.W LPF] and [THROUGH] is not available.
– [R02] is selected in [FADER] and selectable range is [R15] to [00].
22
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO SETTINGS
Crossover settings
Below are the available setting items for 2-way crossover and 3-way crossover.
Caution
Select a crossover type according to how the speakers are connected. ( 33)
If you select a wrong type:
• The speakers may damage.
• The output sound level may be extremely high or low.
SPK SIZE (speaker size)
Selects according to the connected speaker size for optimum performance.
• The frequency and slope settings are automatically set for the crossover of the selected speaker.
• If [NONE] is selected for [TWEETER] of [FRONT], [REAR] and [SUBWOOFER] for [SPK SIZE], the [X ‘ OVER] setting of the selected speaker is not available.
X ‘ OVER (crossover)
[FRQ]/ [HPF FRQ]/ [LPF FRQ]:
Adjusts the crossover frequency for the selected speakers (high pass filter or low pass filter).
• If [THROUGH] is selected, all signals are sent to the selected speakers.
[SLOPE]/ [HPF SLOPE]/ [LPF SLOPE]:
Adjusts the crossover slope.
• Selectable only if a setting other than [THROUGH] is selected for the crossover frequency.
[PHASE]:
Selects the phase of the speaker output to be in line with the other speaker output.
[GAIN LEFT]/ [GAIN RIGHT]/ [GAIN]:
Adjusts the output volume of the selected speaker.
2-way crossover setting items
SPK SIZE
FRONT SIZE
3.5"/ 4"/ 4.75"/ 5"/ 6.5"/ 6.75"/ 7"/ 4×6"/ 5×7"/ 6×8"/ 6×9"/ 7×10"
REAR * 1
TWEETER
SML/ MID/ LRG/ NONE (not connected)
3.5"/ 4"/ 4.75"/ 5"/ 6.5"/ 6.75"/ 7"/ 4×6"/ 5×7"/ 6×8"/ 6×9"/ 7×10"/ NONE (not connected)
SUBWOOFER *
2 * 3
6.5"/ 8"/ 10"/ 12"/ 15" OVER/ NONE (not connected)
X ' OVER
TWEETER
FRONT HPF
FRQ
1KHZ/ 1.6KHZ/ 2.5KHZ/ 4KHZ/ 5KHZ/ 6.3KHZ/ 8KHZ/ 10KHZ/12.5KHZ
GAIN LEFT
–08DB to 00DB
GAIN RIGHT
–08DB to 00DB
FRQ
30HZ/ 40HZ/ 50HZ/ 60HZ/ 70HZ/ 80HZ/ 90HZ/ 100HZ/ 120HZ/ 150HZ/
180HZ/ 220HZ/ 250HZ/ THROUGH
REAR HPF *
1
SLOPE
GAIN
FRQ
–06DB/ –12DB/ –18DB/ –24DB
–08DB to 00DB
30HZ/ 40HZ/ 50HZ/ 60HZ/ 70HZ/ 80HZ/ 90HZ/ 100HZ/ 120HZ/ 150HZ/
180HZ/ 220HZ/ 250HZ/ THROUGH
SLOPE
GAIN
SUB.W LPF *
2 * 3
FRQ
–06DB/ –12DB/ –18DB/ –24DB
–08DB to 00DB
30HZ/ 40HZ/ 50HZ/ 60HZ/ 70HZ/ 80HZ/ 90HZ/ 100HZ/ 120HZ/ 150HZ/
180HZ/ 220HZ/ 250HZ/ THROUGH
–06DB/ –12DB/ –18DB/ –24DB
SLOPE
PHASE
GAIN
REVERSE (180°)/ NORMAL (0°)
–08DB to 00DB
* 1
Displayed only when [SPK/PRE OUT] is set to [REAR/REAR] or [REAR/SUB.W]. ( 22)
* 2
For KW-R920BTS: Displayed only when [SPK/PRE OUT] is set to [REAR/SUB.W] or [SUB.W/SUB.W]. ( 22)
*
3 Displayed only when [SUB.W] is set to [ON]. ( 21)
ENGLISH
23
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
AUDIO SETTINGS
3-way crossover setting items
SPK SIZE
TWEETER SML/ MID/ LRG
MID RANGE
3.5"/ 4"/ 4.75"/ 5"/ 6.5"/ 6.75"/ 7"/ 4×6"/ 5×7"/ 6×8"/ 6×9"
WOOFER *
X ' OVER
6.5"/ 8"/ 10"/ 12"/ 15" OVER/ NONE (not connected)
TWEETER HPF FRQ
1KHZ/ 1.6KHZ/ 2.5KHZ/ 4KHZ/ 5KHZ/ 6.3KHZ/
8KHZ/ 10KHZ/ 12.5KHZ
MID RANGE
SLOPE
PHASE
GAIN
HPF FRQ
HPF SLOPE
LPF FRQ
–06DB/ –12DB
REVERSE (180°)/ NORMAL (0°)
–08DB to 00DB
30HZ/ 40HZ/ 50HZ/ 60HZ/ 70HZ/ 80HZ/ 90HZ/
100HZ/ 120HZ/ 150HZ/ 180HZ/ 220HZ/ 250HZ/
THROUGH
–06DB/ –12DB
1KHZ/ 1.6KHZ/ 2.5KHZ/ 4KHZ/ 5KHZ/ 6.3KHZ/
8KHZ/ 10KHZ/ 12.5KHZ/ THROUGH
–06DB/ –12DB
REVERSE (180°)/ NORMAL (0°)
WOOFER *
LPF SLOPE
PHASE
GAIN
LPF FRQ
SLOPE
–08DB to 00DB
30HZ/ 40HZ/ 50HZ/ 60HZ/ 70HZ/ 80HZ/ 90HZ/
100HZ/ 120HZ/ 150HZ/ 180HZ/ 220HZ/ 250HZ/
THROUGH
–06DB/ –12DB
PHASE
GAIN
REVERSE (180°)/ NORMAL (0°)
–08DB to 00DB
* Displayed only when [SUB.W] is set to [ON]. ( 21)
24
DISPLAY SETTINGS
1
Press and hold .
Press COL to enter [COLOR] directly.
2 Turn the volume knob to select an item (see the following table), then press the knob.
3
Repeat step
2
until the desired item is selected/activated or follow the instructions stated on the selected item.
4 Press to exit.
To return to the previous setting item, press .
Default: XX
DISPLAY
DIMMER
Dim the display and button illuminations.
OFF: Dimmer is turned off.
ON: Dimmer is turned on. Brightness changes to [NIGHT] setting.
( 25, [BRIGHTNESS])
DIMMER TIME: Set the dimmer on and off time.
1 Turn the volume knob to adjust the [ON] time, then press the knob.
2 Turn the volume knob to adjust the [OFF] time, then press the knob.
(Default: [ON]: 18:00 or 6:00 PM
[OFF]: 6:00 or 6:00 AM)
AUTO: Dimmer turns on and off automatically when you turn off or on the car headlights. *
1
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
DISPLAY SETTINGS
BRIGHTNESS
Set the brightness for button and display illuminations for day and night separately.
1 DAY / NIGHT: Select day or night.
2 Select a zone. ( 24)
3 Set the brightness level (00 to 31). (Default: DAY: 31 ; NIGHT: 15)
SCROLL *
2
ONCE: Scrolls the display information once. ; AUTO: Repeats scrolling at
5-second intervals. ; OFF: Cancels.
COLOR
PRESET
Select color for display and button illuminations separately.
Default color:
ALL ZONE: [COLOR 08], DISP ZONE: [COLOR 01],
ZONE 1: [COLOR 08], ZONE 2: [COLOR 46]
1 Select a zone. ( 24)
2 Select a color for the selected zone.
DAY COLOR
NIGHT COLOR
Store your own day and night colors for different zone.
1 Select a zone. ( 24)
2 RED / GREEN / BLUE: Select a primary color.
3 00 to 31: Select the level.
Repeat steps 2 and 3 for all the primary colors.
• Your setting is stored to [USER] in [PRESET].
• If [00] is selected for all primary colors for [DISP ZONE], nothing appears on the display.
COLOR GUIDE
ON: Changes the button and display illuminations when settings are performed on menu and list search. Display zone will automatically change depending on volume level. ; OFF: Cancels.
[NIGHT COLOR] or [DAY COLOR] is changed by turning on or off your car’s headlight.
[NIGHT COLOR] is shown.
speeds.
POP: The selected color pattern is shown.*
3
(Selectable only when
[ALL ZONE] is selected in step
1
.)
* 1
The illumination control wire connection is required. ( 33)
* 2
Some characters or symbols will not be shown correctly (or will be blanked).
*
3
If one of these color pattern is selected, the [ZONE 1], [DISP ZONE], [ZONE 2] illumination color will change to the default color.
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
ENGLISH
25
REFERENCES
Change the display information
Each time you press , the display information changes.
• If the information is unavailable or not recorded, “NO TEXT”, “NO NAME”, or other information (eg. station name) appears.
FM or AM
CD or USB / USB FRONT /
USB REAR
Frequency Day/Clock
(For FM Radio Broadcast Data System stations only)
Station name (PS) Frequency Program type (PTY)
Radio text+ Day/Clock Level meter Level meter with color synchronisation * (back to the beginning)
(For CD-DA)
Playing time Day/Clock Disc name Track title
Level meter Level meter with color synchronisation *
(back to the beginning)
(For MP3/WMA/AAC/WAV/FLAC files)
Playing time Day/Clock Album title/Artist Track title
Folder/file name Level meter Level meter with color synchronisation * (back to the beginning)
USB-IPOD / IPOD FRONT /
IPOD REAR or ANDROID /
ANDROID-F / ANDROID-R
Playing time Day/Clock Album title/Artist Track title
Level meter Level meter with color synchronisation *
(back to the beginning)
PANDORA / PANDORA-F /
PANDORA-R
Station name Shared/Radio Album title Artist Track title Playing time Day/Clock Level meter Level meter with color synchronisation * (back to the beginning)
IHEARTRADIO / IHEART
FRONT / IHEART REAR
SIRIUS XM
Station name Track title Track Artist Day/Clock
Level meter Level meter with color synchronisation *
(back to the beginning)
Channel no./Channel name Artist Song title Content information Category name Day/Clock Level meter
Level meter with color synchronisation * (back to the beginning)
AUX
AUX Day/Clock Level meter Level meter with color synchronisation *
(back to the beginning)
BT AUDIO
Playing time Day/Clock Album title/Artist Track title Level meter
Level meter with color synchronisation * (back to the beginning)
* The color of the button illumination and display illumination changes and synchronises with the sound level.
Maintenance
Cleaning the unit
Wipe off dirt on the faceplate with a dry silicone or soft cloth.
Handling discs:
• Do not touch the recording surface of the disc.
• Do not stick tape etc. on the disc, or use a disc with tape stuck on it.
• Do not use any accessories for the disc.
• Clean from the center of the disc and move outward.
• Clean the disc with a dry silicone or soft cloth. Do not use any solvents.
• When removing discs from this unit, pull them out horizontally.
• Remove burrs from the center hole and disc edge before inserting a disc.
General
• This unit can only play the following CDs:
• DualDisc playback: The Non-DVD side of a “DualDisc” does not comply with the “Compact
Disc Digital Audio” standard. Therefore, the use of Non-DVD side of a DualDisc on this product cannot be recommended.
26
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
REFERENCES
• Detailed information and notes about the playable audio files .
Playable files
• Playable audio file: MP3 (.mp3)/ WMA (.wma)/ AAC (.aac)
• Playable disc media: CD-R/CD-RW/CD-ROM
• Playable disc file format: ISO 9660 Level 1/2, Joliet, Long file name.
• Playable USB device file system: FAT12, FAT16, FAT32
Even when audio files comply with the standards listed above, playback may be impossible depending on the types or conditions of media or device.
The AAC (.m4a) file in a USB device or a CD encoded by iTunes cannot be played on this unit.
Unplayable discs
• Discs that are not round.
• Discs with coloring on the recording surface or discs that are dirty.
• Recordable/ReWritable discs that have not been finalized.
• 8 cm CD. Attempting to insert using an adapter may cause malfunction.
About USB devices
• This unit can play MP3/ WMA/ AAC/ WAV/ FLAC files stored on a USB mass storage class device.
• You cannot connect a USB device via a USB hub.
• Connecting a cable whose total length is longer than 5 m may result in abnormal playback.
• This unit cannot recognize a USB device whose rating is other than 5 V and exceeds 1.5 A.
About iPod/iPhone
Made for
- iPod touch (2nd, 3rd, 4th, and 5th generation)
- iPod classic
- iPod nano (3rd, 4th, 5th, 6th, and 7th generation)
- iPhone 3G, 3GS, 4, 4S, 5, 5S, 5C, 6, 6 Plus
• It is not possible to browse video files on the “Videos” menu in [HEAD MODE].
• The song order displayed on the selection menu of this unit may differ from that of the iPod/ iPhone.
• Depending on the version of the operating system of the iPod/iPhone, some functions may not operate on this unit.
About Android device
• This unit supports Android OS 4.1 and above.
• Some Android devices (with OS 4.1 and above) may not fully support Android Open Accessory
(AOA) 2.0.
• If the Android device supports both mass storage class device and AOA 2.0, this unit always playback via AOA 2.0 as priority.
About iHeartRadio
• iHeartRadio® is a third-party service, therefore the specifications are subject to change without prior notice. Accordingly, compatibility may be impaired or some or all of the services may become unavailable.
• Some iHeartRadio® functionality cannot be operated from this unit.
About Bluetooth
• Depending on the Bluetooth version of the device, some Bluetooth devices may not be able to connect to this unit.
• This unit may not work with some Bluetooth devices.
• Signal conditions vary, depending on the surroundings.
ENGLISH
27
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
TROUBLESHOOTING
Symptom Remedy
Sound cannot be heard.
• Adjust the volume to the optimum level.
• Check the cords and connections.
“MISWIRING CHECK
WIRING THEN PWR ON” appears.
Turn the power off, then check to be sure the terminals of the speaker wires are insulated properly. Turn the power on again.
“PROTECTING SEND
SERVICE” appears.
Send the unit to the nearest service center.
Source cannot be selected. Check the [SRC SELECT] setting. ( 4)
Connect the antenna firmly.
• Radio reception is poor.
• Static noise while listening to the radio.
Disc cannot be ejected.
Press and hold to forcibly eject the disc. Be careful not to drop the disc when it is ejected.
“IN DISC” appears.
Make sure nothing is blocking the loading slot when you eject the disc.
Press , then insert the disc correctly.
“PLEASE” and “EJECT” appear alternately.
Playback order is not as intended.
The playback order is determined by the file name (USB) or the order in which files were recorded (disc).
This depends on the recording process earlier.
Elapsed playing time is not correct.
“NOT SUPPORT” appears and track skips.
Check whether the track is a playable format. ( 27)
“READING” keeps flashing. • Do not use too many hierarchical levels and folders.
• Reload the disc or reattach the USB device.
“CANNOT PLAY” flashes and/or connected device cannot be detected.
• Check whether the connected device is compatible with this unit and ensure the files are in supported formats. ( 27)
• Reattach the device.
28
Symptom
The iPod/iPhone does not turn on or does not work.
Remedy
• Check the connection between this unit and iPod/iPhone.
• Detach and reset the iPod/iPhone using hard reset.
“LOADING” appears when you enter search mode by pressing .
Correct characters are not displayed.
• Sound cannot be heard during playback.
• Sound output only from the Android device.
This unit is still preparing the iPod/iPhone music list. It may take some time to load, try again later.
• This unit can only display uppercase letters, numbers, and a limited number of symbols.
• Depending on the display language you have selected
( 5), some characters may not be displayed correctly.
• Reconnect the Android device.
• If in [ AUDIO MODE], launch any media player application on the Android device and start playback.
• If in [ AUDIO MODE], relaunch the current media player application or use another media player application.
• Restart the Android device.
• If this does not solve the problem, the connected Android device is unable to route the audio signal to unit. ( 27)
[
Cannot playback at
AUTO MODE].
“NO DEVICE” or “READING” keeps flashing.
• Make sure JVC MUSIC PLAY APP is installed on the
Android device. ( 7)
• Reconnect the Android device and select the appropriate control mode. ( 8)
• If this does not solve the problem, the connected Android device does not support [ AUTO MODE]. ( 27)
• Switch off the developer options on the Android device.
• Reconnect the Android device.
• If this does not solve the problem, the connected Android device does not support [ AUTO MODE]. ( 27)
Turn off the power saving mode on the Android device.
Playback is intermittent or sound skips.
“CANNOT PLAY” • Make sure Android device contains playable audio files.
• Reconnect the Android device.
• Restart the Android device.
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
TROUBLESHOOTING
Symptom Remedy
“ADD ERROR”
“CHK DEVICE”
“NO SKIPS”
“NO STATIONS”
“STATION LMT”
New station creation is unsuccessful.
Check the Pandora application on your device.
The skip limit has been reached.
No stations are found.
The number of registered stations has reached its limit.
Retry after deleting unnecessary stations from your device.
“UPGRADE APP” Make sure you have installed the latest version of the
Pandora application on your device.
Communication is unstable.
“CONNECT ERR”
“RATING ERR” Registration of thumbs up/thumbs down has failed due to insufficient network connectivity.
Registration of thumbs up/thumbs down is not allowed.
“THUMBS N/A”
“LICENSE ERR” You try to access from a country which Pandora is not deliverable.
Station cannot be selected.
If “Explicit Content” in [Account Settings] is checked in the web version of iHeartRADIO, custom stations become unavailable.
“NOT CONNCTD” Link to the application is impossible.
“CH LOCKED LOCK CODE?” The selected channel is locked. Enter the correct pass code to unlock. ( 13)
“CHAN UNSUB” The selected channel is unsubscribed.
“CH UNAVAIL” The selected channel is unavailable.
Symptom
“CHK ANTENNA”
Remedy
Check that the antenna and its connection are in good condition.
“CHECK TUNER” Make sure the SiriusXM Vehicle Tuner is connected to the unit.
Make sure the antenna is mounted outside the vehicle.
“NO SIGNAL”
“SUBSCRIPTION UPDATED –
PRESS ENTER TO CONTINUE.”
“CODE ERROR”
“NO CONTENT”
“SCAN CANCEL”
Your subscription is updated. Press the volume knob to continue.
Make sure you have entered the correct pass code.
( 13)
There is insufficient content to start TuneScan.
TuneScan has been aborted.
No Bluetooth device is detected.
• Search from the Bluetooth device again.
• Reset the unit. ( 3)
Pairing cannot be made.
• Make sure you have entered the same PIN code to both the unit and Bluetooth device.
• Delete pairing information from both the unit and the
Bluetooth device, then perform pairing again. ( 14)
Echo or noise occurs.
• Adjust the microphone unit’s position. ( 14)
• Check the [ECHO CANCEL] setting. ( 16)
Phone sound quality is poor.
Sound is being interrupted or skipped during playback of a
Bluetooth audio player.
• Reduce the distance between the unit and the Bluetooth device.
• Move the car to a place where you can get a better signal reception.
• Reduce the distance between the unit and the Bluetooth audio player.
• Turn off, then turn on the unit and try to connect again.
• Other Bluetooth devices might be trying to connect to the unit.
ENGLISH
29
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
TROUBLESHOOTING
Symptom
The connected
Bluetooth audio player cannot be controlled.
“PAIRING FULL”
“PLEASE WAIT”
“NOT SUPPORT”
“ERROR”
“H/W ERROR”
Remedy
• Check whether the connected Bluetooth audio player supports Audio/Video Remote Control Profile (AVRCP).
(Refer to the instructions of your audio player.)
• Disconnect and connect the Bluetooth player again.
The number of registered devices has reached its limit.
Retry after deleting an unnecessary device. ( 18, DELETE
PAIR)
The unit is preparing to use the Bluetooth function. If the message does not disappear, turn off and turn on the unit, then connect the device again.
The connected phone does not support Voice Recognition feature.
Try the operation again. If “ERROR” appears again, check if the device supports the function you have tried.
Reset the unit and try the operation again. If “H/W ERROR” appears again, consult your nearest service center.
SPECIFICATIONS
FM Frequency Range 87.9 MHz — 107.9 MHz (200 kHz step)
87.5 MHz — 108.0 MHz (50 kHz step)
50 kHz/200 kHz Channel Space Selection
Usable Sensitivity (S/N = 26 dB) 8.2 dBf (0.71 μV/75 Ω)
Quieting Sensitivity (DIN S/N = 46 dB) 17.2 dBf (2.0 μV/75 Ω)
Frequency Response (±3 dB) 30 Hz — 15 kHz
Signal-to-Noise Ratio (MONO)
Stereo Separation (1 kHz)
AM Frequency Range
Channel Space Selection
Usable Sensitivity (S/N = 20 dB)
64 dB
40 dB
530 kHz — 1 700 kHz (10 kHz step)
531 kHz — 1 611 kHz (9 kHz step)
9 kHz/10 kHz
29 dBμ (28.2 μV)
Laser Diode
Digital Filter (D/A)
Spindle Speed
Wow & Flutter
Frequency Response (±1 dB)
Total Harmonic Distortion (1 kHz)
Signal-to-Noise Ratio (1 kHz)
Dynamic Range
Channel Separation
MP3 Decode
WMA Decode
AAC Decode
GaAIAs
8 times over sampling
500 rpm — 200 rpm (CLV)
Below measurable limit
20 Hz — 20 kHz
0.01 %
105 dB
90 dB
85 dB
Compliant with MPEG-1/2 Audio Layer-3
Compliant with Windows Media Audio
AAC-LC “.aac” files
30
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
SPECIFICATIONS
USB Standard
Compatible Devices
File System
Maximum Supply Current
Digital Filter (D/A) Converter
MP3 Decode
WMA Decode
AAC Decode
WAV Decode
FLAC Decode
Frequency Response (±3 dB)
Input Maximum Voltage
Input Impedance
Version
Frequency Range
Output Power
Maximum Communication Range
Pairing
Profile
USB 1.1, USB 2.0 (Full speed)
Mass storage class
FAT12/ 16/ 32
DC 5 V 1.5 A
24 Bit
Compliant with MPEG-1/2 Audio Layer-3
Compliant with Windows Media Audio
AAC-LC “.aac” files
Linear-PCM
FLAC files
20 Hz — 20 kHz
1 000 mV
30 kΩ
Bluetooth Ver.2.1+EDR/ Bluetooth 3.0
2.402 GHz — 2.480 GHz
+4 dBm (MAX), 0 dBm (AVE) Power Class 2
Line of sight approx. 10 m (32.8 ft)
SSP (Secure Simple Pairing)
HFP1.6 (Hands-Free Profile)
A2DP (Advanced Audio Distribution Profile)
AVRCP1.5 (Audio/Video Remote Control Profile)
PBAP (Phonebook Access Profile)
SPP (Serial Port Profile)
Maximum Output Power 50 W × 4 or
50 W × 2 + 50 W × 1 (Subwoofer = 4 Ω)
22 W × 4 Full Bandwidth Power
(at less than 1 % THD)
Speaker Impedance
Preout Level/Load (CD/USB)
Preout Impedance
4 Ω — 8 Ω
4 000 mV/10 kΩ load
≤ 600 Ω
Operating Voltage
(10.5 V — 16 V allowable)
Maximum Current Consumption
Operating Temperature Range
Installation Size (W × H × D)
Weight
Subject to change without notice.
14.4 V
10 A
–10°C — +60°C
178 mm × 100 mm × 158 mm
(7-1/16" × 3-15/16" × 6-1/4")
1.3 k g
(3 lbs)
ENGLISH
31
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Warning
• The unit can only be used with a 12 V DC power supply, negative ground.
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or
Ground wire (black) to prevent a short circuit.
• Insulate unconnected wires with vinyl tape to prevent a short circuit.
• Be sure to ground this unit to the car’s chassis again after installation.
Caution
• For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
• Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.
• Do not connect the wires of speakers to the car chassis or Ground wire (black), or connect them in parallel.
• Connect speakers with a maximum power of more than 50 W. If the maximum power of the speakers is lower than 50 W, change the [AMP GAIN] setting to avoid damaging the speakers. ( 21)
• Mount the unit at an angle of less than 30º.
• If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red) to the terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned on and off by the ignition key.
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working properly.
• If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old fuse with one that has the same rating.
Basic procedure
1
Remove the key from the ignition switch, then disconnect the
terminal of the car battery.
2 Connect the wires properly.
32
3
Install the unit to your car.
See Installing the unit (in-dash mounting).
4 Connect the terminal of the car battery.
5 Press to turn on the power.
6
Reset the unit within 5 seconds. ( 3)
Installing the unit (in-dash mounting)
Install onto the car brackets using the supplied screws (B) or (C). The screw holes differ depending on the model of the cars.
Do the required wiring. ( 33)
Dashboard of your car
Use only the specified screws. Using wrong screws might damage the unit.
Part list for installation
(A) Wiring harness (B) Flat head screw
M5 × 8 mm (M5 × 3/8")
Car bracket
(C) Round head screw
M5 × 8 mm (M5 × 3/8")
Output terminals
KW-R925BTS REAR
FRONT
SW
KW-R920BTS FRONT
REAR/SW
For 2-way crossover setting For 3-way crossover setting
: Rear output
: Front output
: Subwoofer output
: Front output
: Rear/subwoofer output
: Tweeter output
: Mid Range output
: Woofer output
: Mid Range output
: Woofer output
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
Wiring connection
Output terminals ( 32)
Signal cord (not supplied)
Vehicle dashboard
Factory wiring harness (vehicle)
Custom wiring harness
(separately purchased)
* 1
Firmly connect the ground wire of the amplifier to the car’s chassis to avoid damaging the unit.
* 2
You can also connect a subwoofer speaker directly using this lead without an external subwoofer amplifier.
For setting, 22.
Recommended connection
To the steering wheel remote control adapter
Antenna terminal
Light blue/yellow
STEERING
WHEEL
REMOTE
Join the same color wires together.
Blue: To power antenna
Blue/white: To amplifier
Blue/white: Remote (200 mA max.)
Orange/white: Illumination
Brown
(Not used)
Fuse (10 A)
Yellow: Battery 12 V
Red: Ignition 12 V
Black: Ground
Gray: Front speaker/For 3-way crossover: Mid range speaker (right)
Gray/black
White: Front speaker/For 3-way crossover: Mid range speaker (left)
White/black
Purple: Rear speaker/For 3-way crossover: Tweeter (right)
Purple/black
Green: Rear speaker *
2
/For 3-way crossover: Tweeter (left)
Green/black *
2
JVC Amplifier *
1
(For KW-R925BTS)
USB cable (DC 5 V
(approx. 1.2 m/4 feet)
1.5 A)
MIC (Microphone input terminal) ( 14)
Expansion port (12 V 500 mA)
To the optional SiriusXM Vehicle Tuner
(commercially available) ( 11)
Remote wire
(not supplied)
Ignition switch
Car fuse block
Separate red wire
Make this connection if your vehicle factory wiring harness does not have “12 V ignition switch” wire.
IMPORTANT
We recommend installing the unit with a commercially available custom wiring harness specific for your car and leave this job to professionals for your safety. Consult your car audio dealer.
ENGLISH
33
Data Size: B6L (182 mm x 128 mm)
Book Size: B6L (182 mm x 128 mm)
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project