Honda ST1300 NT700V Accessory Socket Installation Instructions 7 Pages
Honda ST1300 NT700V Accessory Socket Installation Instructions
The Honda Accessory Socket ST1300, NT700V is a 12V DC accessory socket that can be used to power a variety of accessories, such as GPS units, cell phone chargers, and heated gear. The socket is installed on the motorcycle's bodywork and is connected to the motorcycle's electrical system. The socket is equipped with a safety label that should be attached to the inside of the pocket lid once installation is complete.
advertisement
INSTALLATION
INSTRUCTIONS
Accessory
12V DC ACCESSORY SOCKET
P/N 08V70-MCS-100
Application
ST1300 / NT700V
Publications No.
MII 12941
Issue Date
August 2009
Honda Dealer: Please give a copy of these instructions to your customer.
PARTS LIST
SOCKET HARNESS
INSTALLATION (ST1300)
NOTE:
• The Quartet Harness (P/N 08A30-MCS-100) which is sold separately is required to install the Accessory
Socket Kit.
• Disconnect the negative cable from the battery before installing this accessory.
• The tripmeter and clock will be reset when you disconnect the battery.
SOCKET RING
SOCKET
1.
Remove the parts from the motorcycle as described in the Service Manual.
Around The Front of the Motorcycle
SCREW
(2)
CLIP
(3)
(1)
No.
(1)
(2)
(3)
Description
ACC socket assy.
Safety label
Wire tie
Qty
1
1
3
TOOLS AND SUPPLIES REQUIRED
Electric drill motor
Hole saw (32 mm)
Marker
Ruler
Isopropyl alcohol
Shop towel
OPERATION
• Use a 2A blade fuse when the fuse needs to be replaced with a new one.
RIGHT REAR VIEW MIRROR COVER
Around The Meter Panel
LEFT REAR VIEW
MIRROR COVER
SCREW
© 2009 American Honda Motor Co., Inc - All Rights Reserved.
08V70-MCS-1002-91
CLIP
1 of 7
Around The Cowl
CLIP
SOCKET BOLT
METER PANEL
RIGHT INNER COWL
RIGHT
MIDDLE
COWL
RIGHT ENGINE
GUARD COVER
RIGHT LOWER COWL
INNER LOWER COWL
2.
Remove the right pocket lid from the right middle cowl.
SCREW
RIGHT MIDDLE COWL
RIGHT POCKET LID
BOLT
CLIP
SCREW
CLIP
2 of 7
08V70-MCS-1002-91 © 2009 American Honda Motor Co., Inc - All Rights Reserved.
2.
Using a marker and ruler, measure and mark the right pocket lid as shown.
25 mm
MARKER
5.
Install the accessory socket in the 32 mm hole you just made, then attach the safety label to the inside of the pocket lid in the area shown.
• Remove the fuse box cover before routing the socket ring.
SAFETY LABEL
Remove the adhesive baking before attaching.
RIGHT POCKET LID
SOCKET RING
25 mm
RIGHT POCKET LID
4.
Using an electric drill motor and hole saw, drill a 32 mm hole through the mark you just made.
• Remove any burrs from the edge of the hole.
ACC SOCKET
ISOPROPYL ALCOHOL
Thoroughly clean the area where the safety label will be attached.
6.
Reinstall the right pocket lid on the right body cowl in the reverse order of removal.
7.
Route and connect the socket harness to the quartet harness as shown.
SOCKET HARNESS
MARK
ELECTRIC DRILL MOTOR
(32 mm HOLE SAW)
QUARTET
HARNESS
© 2009 American Honda Motor Co., Inc - All Rights Reserved.
RIGHT POCKET LID
3-PIN CONNECTOR
(RED)
08V70-MCS-1002-91
FUSE BOX
3 of 7
8.
Connect the accessory socket as shown, then reinstall the right body cowl in the reverse order of removal. Secure the wire harnesses with the wire ties in the areas shown.
Right Side
WIRE TIE
Secure to the motorcycle’s frame.
WIRE TIE
MOTORCYCLE’S
HARNESS
Left Side
WIRE TIE
Secure to the motorcycle’s harness.
SOCKET HARNESS
9.
Reinstall all removed parts in the reverse order of removal.
4 of 7
08V70-MCS-1002-91
WIRE TIE
© 2009 American Honda Motor Co., Inc - All Rights Reserved.
INSTALLATION (NT700V)
NOTE:
• The sub harness kit (P/N 08A30-MEW-100) which is sold separately, is required to install the Accessory
Socket Kit.
• Disconnect the negative cable from the battery before installing this accessory.
• The tripmeter and clock will be reset when you disconnect the battery.
1.
Remove the seat and left side cover from the motorcycle as shown.
SEAT
3.
Remove the clips from the middle cowl as shown.
CLIP
4.
Refer to the Service Manual for the motorcycle, remove the motorcycle parts.
METER PANEL RIGHT POCKET LID
SCREW
BOLT
SCREW
BOLT
WASHER
LEFT
POCKET LID
LEFT SIDE COVER
2.
Raise the wind screen as shown.
SCREEN
RIGHT
LEFT POCKET
© 2009 American Honda Motor Co., Inc - All Rights Reserved.
08V70-MCS-1002-91
5 of 7
BOLT LEFT MIRROR 6.
Using an electric drill motor and hole saw, drill a 32 mm hole through the mark you just made.
• Remove any burrs from the edge of the hole.
SCREW
MARK
LEFT PANEL
SCREW FRONT COWL
BOLT
LEFT COWL
BOLT
BOLT
LEFT ENGINE
GUARD COVER
5.
Using a marker and ruler, measure and mark the left pocket as shown.
MARKER
ELECTRIC DRILL MOTOR
(32 mm HOLE SAW)
7.
Install the accessory socket in the 32 mm hole you just made, then attach the safety label to the inside of the left pocket in the area shown.
• Remove the fuse box cover before routing the socket ring.
SAFETY LABEL
Remove the adhesive baking before attaching.
ISOPROPYL ALCOHOL
Thoroughly clean the area where the safety label will be attached.
SOCKET RING
LEFT POCKET
LEFT POCKET 42 mm
6 of 7
90 mm
ACC SOCKET
08V70-MCS-1002-91
LEFT POCKET
© 2009 American Honda Motor Co., Inc - All Rights Reserved.
8.
Connect the socket harness to the sub harness as shown.
LEFT POCKET
SOCKET HARNESS
SUB HARNESS
3-PIN CONNECTOR (White)
FUSE BOX
9.
Install the motorcycle’s parts in the reverse order of removal.
LEFT POCKET
© 2009 American Honda Motor Co., Inc - All Rights Reserved.
08V70-MCS-1002-91
7 of 7
advertisement
Key Features
- 12V DC power outlet
- Designed for Honda ST1300 and NT700V models
- Requires separate Quartet Harness (ST1300) or Sub Harness Kit (NT700V)
- Safety label included
- Installation instructions provided
Frequently Answers and Questions
What is the Quartet Harness and why is it required for installation on the ST1300?
What is the Sub Harness Kit and why is it required for installation on the NT700V?
What kind of fuse should I use with the accessory socket?
What happens to the tripmeter and clock when I disconnect the battery?
Related manuals
advertisement