Asko ADA series Installation Instructions Manual

Installation Instructions

FI Dishwasher

CONTENTS

INTRODUCTION ......................................................................................................................... 2

WHAT YOU NEED ...................................................................................................................... 2

SAFETY INSTRUCTIONS ............................................................................................................ 3

BEFORE STARTING THE INSTALLATION .................................................................................. 3

XXL DISHWASHERS ................................................................................................................... 4

– UNIT DIMENSIONS ............................................................................................................... 4

– PREPARING THE LOCATION ................................................................................................ 4

ADA AND XL DISHWASHERS .................................................................................................... 5

– UNIT DIMENSIONS ............................................................................................................... 5

– PREPARING THE LOCATION ................................................................................................ 5

– ADAFI TRIM KIT INSTALLATION OPTIONS .......................................................................... 6

STEP 1. FITTING THE DISHWASHER IN PLACE........................................................................ 7

STEP 2. ATTACHING THE ACCESSORY DOOR OR CUSTOM PANEL .................................... 10

STEP 3. ADJUSTING THE DOOR SPRINGS ............................................................................ 11

STEP 4. CONNECTING ELECTRICITY, WATER, AND DRAIN .................................................. 12

STEP 5. CHECKING DISHWASHER FUNCTION AND FIT ....................................................... 15

STEP 6. SECURING THE DISHWASHER.................................................................................. 15

STEP 7. ATTACHING THE TOE KICK (IF APPLICABLE) .......................................................... 17

INSTALLATION CHECKLIST ..................................................................................................... 20

IMPORTANT!

READ ALL OF THESE INSTRUCTIONS BEFORE INSTALLING THE DISHWASHER.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

492181 Install DW16 FI USA EN Rev 03.indd 1 2016-05-31 10:32:38

INTRODUCTION

Read these instructions carefully and completely before you install the machine. The installation should be carried out by a qualified person who is familiar with all local codes and ordinances for electrical and plumbing connections.

WHAT YOU NEED

TOOLS

1) Phillips No. 2 screwdriver

2) Flat blade screwdriver

3) Torx screwdriver size T 20

4) Adjustable wrenches (if you use copper fittings)

5) Open-ended wrench

(1/2˝ [12 mm], 5/8˝ [16 mm] and 1˝ [24 mm])

6) Tape measure

7) Spirit level

8) Electric drill with 1-1/2˝ drill bit

9) Keyhole saw

MATERIALS SUPPLIED

NOTE:

Cosmetic damage must be reported to the ASKO dealer within five days from the date of purchase. As soon as you unpack the dishwasher, thoroughly check it for cosmetic damage.

*

1

*

7

*

2

*

8

2

3

5

6

4

6x

1-1/2"

(38 mm)

2x

3/8"

(10 mm)

2x 2x

1"

(25 mm)

* Only select models.

MATERIALS

• Minimum 3/8" OD copper tubing of sufficient length for your installation

• Shut-off valve and fittings for water supply line

AUTOMATIC HIGH LOOP

The drain hose is fastened to the back of the machine at the best height. To eliminate potential drain problems, leave this hose in place.

CUSTOMER CARE CENTER 1-800-898-1879 • WWW.ASKONA.COM



3

2 CUSTOMER CARE CENTER 1-800-898-1879 • WWW.ASKONA.COM

SAFETY INSTRUCTIONS

• It is important that you closely follow the instructions provided here.

• An incorrect or defective installation can lead to higher consumption of energy, water and dishwashing detergent, which can lead to higher costs and poor cleaning results.

• Plumbing and electrical installations must be carried out by qualified professionals.

• Exercise caution during the installation! Wear protective gloves! Always work in pairs!

• The power outlet for the dishwasher should be installed in a location that is easily accessible once the dishwasher is installed.

• Always follow the applicable regulations for water, drain and electrical connection.

• If a dishwasher must be hard wired, it must be connected to a grounded circuit.

WARNING!

Turn off the water supply when installing the dishwasher!

BEFORE STARTING THE INSTALLATION

Connection to water supply:

• T here must be a shut off valve on the water supply pipe. The shut off valve should be installed in a location that is easily accessible so that the water may be shut off in the event that the dishwasher needs to be moved.

Installation advice:

• Cable holes for wires/cables need not be larger than

1-1/2˝ (38 mm).

• Attach the light shielding film (see FITTING THE

DISHWASHER IN PLACE). Only select models.

NOTE:

Check that the fitting and connection measurements are correct. See UNIT DIMENSIONS and PREPARING

THE LOCATION.

XXL/XL?

?

XXL

[ mm]

See page 4

XL

See page 5

XL / XXL

492181 Install DW16 FI USA EN Rev 03.indd 3


3

2016-05-31 10:32:39

XXL DISHWASHERS

UNIT DIMENSIONS

Height (Adjustable)

Width

Depth (Includes high loop)

Depth W/Door Open

Weight

23-5/8"

596 mm

U.S.

33-7/8˝ to 35-7/8˝

23-5/8˝

22-7/8˝

49-1/2˝

110 Ib

Metric

861 mm to 912 mm

596 mm

581 mm

1258 mm

50 kg

49-1/2"

1258 mm

22-7/8"

581 mm

Technical Data

Electricity 120V, 60Hz, 15 amp

Water pressure 4.2 - 140 psi,

0.03-1.0 MPa,

0.3-10 Bar

Heating element 1200 watt

Max loading 1300 watt

4

2-7/8"

74 mm

Door

3-1/8"

79 mm

3-3/8"

85 mm

9"

228 mm

Reverse hose within the high loop bracket to accommodate a left side drain.

PREPARING THE LOCATION

The best place for your dishwasher is in the kitchen near the sink. This makes it easier to connect the water and drain supply lines.

A built-in dishwasher must be enclosed on the top, both sides and the back.

The power-supply receptacle for the appliance shall be installed in a cabinet or on a wall adjacent to the undercounter space in whitch the appliance is to be installed.

The electrical and water supplies should enter through the area indicated by the shading on the illustration at right. Preferably, they should come through the right side of the machine. The access hole must be round and smooth and no bigger than 1-1/2˝ (38 mm) in diameter. If the partition is metal, it needs to be covered with an edge protector. Use caution when the appliance is installed or removed, to reduce the likelihood of damage to the power-supply cord.

** If accessory FI fill strips are used, then 1/2˝ (13 mm) must be added to the dishwasher height and cutout. Additionally,

3/8˝ (10 mm) must be added to the dishwasher width and cutout width. Remove locking nuts for an installed height of 33-7/8˝ (860-861 mm).

Cutout Dimensions

U.S.

Height** 33-7/8˝ – 36˝

Width 23-5/8 – 24˝

Depth 24˝

Metric

860 – 914 mm

600 – 610 mm

610 mm

3

/

4

”

(19)

TYPICAL

3 ½” (89)

FINISHED

RETURN

W

FRAMELESS CABINETRY

3 ½” (89)

FINISHED

RETURN

FILLER

W

FRAMED CABINETRY

Framed cabinets will require additional finished filler material behind the face frame for a proper installation.

2"

51 mm

4"

102 mm

5-3/8"

136 mm

24"

610 mm

23-5/8" – 24"

600 – 610 mm




5


ADA AND XL DISHWASHERS

UNIT DIMENSIONS

Height (Adjustable)*

Width

Depth (Includes high loop)

Depth W/Door Open

Weight

23-5/8"

596 mm

U.S.

32-3/8˝ to 34-1/4˝

23-5/8˝

22-7/8˝

48-3/8˝

108 Ib

Metric

821 mm to 872 mm

596 mm

581 mm

1229 mm

49 kg

48-3/8"

1218 mm

22-7/8"

581 mm

Technical Data

Electricity 120V, 60Hz, 15 amp

Water pressure 4.2 - 140 psi,

0.03-1.0 MPa,

0.3-10 Bar

Heating element 1200 watt

Max loading 1300 watt

2-7/8"

74 mm

Door

3-1/8"

79 mm 3-3/8"

85 mm

9"

228 mm

Reverse hose within the high loop bracket to accommodate a left side drain.

PREPARING THE LOCATION

The best place for your dishwasher is in the kitchen near the sink. This makes it easier to connect the water and drain supply lines.

A built-in dishwasher must be enclosed on the top, both sides and the back.

The power-supply receptacle for the appliance shall be installed in a cabinet or on a wall adjacent to the undercounter space in whitch the appliance is to be installed.

The electrical and water supplies should enter through the area indicated by the shading on the illustration at right. Preferably, they should come through the right side of the machine. The access hole must be round and smooth and no bigger than 1-1/2˝ (38 mm) in diameter. If the partition is metal, it needs to be covered with an edge protector. Use caution when the appliance is installed or removed, to reduce the likelihood of damage to the power-supply cord.

* 32-1/4˝ (820 mm) height requires removal of top trim, and lowering side trim (2). Remove locking nuts for an installed height of 32-1/4˝ (820-821 mm).

Cutout Dimensions

U.S.

Height* 32-1/4˝ – 34˝

Width 23-5/8 – 24˝

Depth 24˝

Metric

820 – 864 mm

600 – 610 mm

610 mm

3

/

4

”

(19)

TYPICAL

3 ½” (89)

FINISHED

RETURN

W

FRAMELESS CABINETRY

3 ½” (89)

FINISHED

RETURN

FILLER

W

FRAMED CABINETRY

Framed cabinets will require additional finished filler material behind the face frame for a proper installation.

2"

51 mm

4"

102 mm

5-3/8"

136 mm

24"

610 mm

23-5/8” – 24"

600 mm – 610 mm


5


ADAFI TRIM KIT INSTALLATION OPTIONS

ASKO XLADAFI dishwashers can be installed either with or without accessory fill strips depending on the type of installation. If the dishwasher cutout has been cut to European widths of 23-5/8˝ (600 mm), the unit won’t require fill strips. If the dishwasher cutout is a standard 24˝ (610 mm) wide, we have fill strips that make the unit 24˝ (610 mm) wide.

23-5/8˝ (600 mm) Wide Door Panels

The ASKO accessory fill kit for 23 5/8˝ (600 mm) Width

Door Panels (445006), which includes the counter saver fill strip and both side fill strips, should be installed in the back mounting holes.

23-7/8˝ (606 mm) Wide Door Panels

The ASKO accessory fill kit for 23-7/8˝ (606 mm) Width

Door Panels (445008) which includes the counter saver fill strip and both side fill strips, should be installed in the front mounting holes.

6



2016-05-31 10:32:42


7


STEP 1. FITTING THE DISHWASHER IN PLACE

1. Be sure to remove the transport protection for the door when unpacking the dishwasher.

2x

2. Attach the light shielding film (packed in the document bag) to the underside of the countertop above the touch buttons. (Only certain models).

!

The light shielding film ensures optimal button functionality.

NOTE:

The surface on which the protective film is to be attached must be clean and dry.

3. Attach the supplied door sealing

(only certain models).

This strip is an essential part of the Turbo Dry

Express system and must be installed to ensure an optimum seal between the dishwasher tank and door.

2

1

2

1

4. Start by measuring the height from the floor to the bottom edge of the counter top. Measure the height from the floor to the top edge of the dishwasher.

5. Loosen the lock nuts on the dishwasher’s steel feet using a 5/8 inch (16 mm) open-ended wrench.

Screw the lock nuts down as close to the floor as possible.


5/8" (16 mm)


7

2016-05-31 10:32:45


6. Adjust the front feet by turning them clockwise to raise or counterclockwise to lower the dishwasher.

Leave enough space to adjust them later.

1˝ (24 mm)

7. Screw in the back foot completely by turning the adjustment screw at the front counterclockwise.

Use a flat-bladed screwdriver or a 1/4˝ nut driver.

(Only models with front adjustable rear foot).

If the machine does not have a front adjustable rear foot, level the remaining rear legs just as you did the front legs.

8. Push the dishwasher into the cabinet. At the same time, pull the power cord, the drain hose, and the fill hose through the appropriate cut outs.

Use caution when sliding the dishwasher into place. The protective slides could cause damage to certain types of soft flooring.

NOTE:

If installing in a metal cabinet, the hole(s) for the drain hose and connection pipe must be fitted with edge protectors/rubber grommets.

9. Lift the dishwasher a little at the front and turn the front feet to lower them.

10. Check that the height of the machine corresponds to the height from the floor to the bottom edge of the counter top.

1˝ (24 mm)

8



2016-05-31 10:32:46


9


11. Adjust the back foot by turning the adjustment screw at the front clockwise. (Only models with front adjustable rear foot.)

If the machine does not have a front adjustable rear foot, level the remaining rear legs just as you did the front legs.

12. Place the spirit level on the dishwasher door to check that the machine is level and adjust if necessary. The door must be fully closed!

NOTE:

The dishwasher must be level!

An unlevel machine can affect the amount of water taken in, the door can be difficult to close, and the baskets difficult to place securely.




9

2016-05-31 10:32:46

*

1

STEP 2. ATTACHING THE ACCESSORY DOOR OR CUSTOM PANEL

Follow the separate instructions supplied with the dishwasher to attach the chosen accessory door or custom panel to the front of the machine.

NOTE:

Once you have fitted the accessory door or custom panel to the dishwasher, the door springs may need adjusting. Check that the door stays in the position in which it is placed. If the door drops down when you open it, the springs need to be tightened. If the door shuts on its own, the springs need to be loosened. See step 3 for further instructions.

NOTE:

The custom panel must not cover the air nozzle and thereby block the flow of air.

3

4

*

2

5

6

6x

1-1/2"

(38 mm)

2x

3/8"

(10 mm)

2x 2x

1"

(25 mm)

Custom Panel Dimensions

Width Height

Custom panel XL (4” toe kick) 23

3

/

8

” (600 mm) 28-1/8” (714 mm)

Custom panel XXL (4” toe kick) 23

3

/

8

” (600 mm) 30-1/8” (765 mm)

Custom panel XXL (6” toe kick) 23 3 /

8

” (600 mm) 28-1/8” (714 mm)

Panel Requirements

Max. Weight (including handle) 20 lb (9 kg)

Min. Thickness 3/4” (19mm)

Typical panel dimensions are based on a

23

5

/

8

” (600 mm) opening width and 34 ½” (876 mm) finished height, with a minimum 4” (102 mm) toe kick and

1

/

8

” (3 mm) reveals. For all other opening widths, the panel should be ¼” (6 mm ) less than the opening to achieve minimum reveals. Panel dimensions must be adjusted accordingly for all other installations.

10



2016-05-31 10:32:47

*

7

*

8


11

STEP 3. ADJUSTING THE DOOR SPRINGS

XL = 3-11 kg

XXL = 1-9 kg

Check that the door is balanced. It should not fall open or snap shut. Adjust as necessary.

1. If you need to adjust the door spring tension, use a screwdriver to turn the hexagonal headed screw located at the front of the machine.

The maxium weight for the door panel on units with this type of springs is 19 lbs. Heavier springs are not available for this unit.

Adjustable spring




11

2016-05-31 10:32:49

STEP 4. CONNECTING ELECTRICITY, WATER, AND DRAIN

1.

CONNECT DRAIN HOSE

ASKO provides a 7/8˝ (22 mm) diameter corrugated drain hose which is connected to the back of the unit to form a high loop.

THREE WAYS TO INSTALL

DRAIN CONNECTIONS

A) Typical connection to sink plumbing before trap

(high loop drain)

NOTE:

Do not use any fittings anywhere in the drain line that are less than 7/8˝ (22 mm) OD.

The access hole for the drain line should be 1-5/8˝ (41 mm)- 2˝ (50mm) max.

The end of the drain line is 1/2˝ (12 mm), but it is adjustable to 7/8˝, 3/4˝, 5/8˝ (22mm, 19 mm, and 16 mm). If the drain connection is larger than

1/2˝ (12 mm), you can easily cut the drain line to fit the connection.

The illustrations to the right show three ways to connect the drain supply line.

24 ″ min.

(610 mm)

20 ″ min.

(508 mm)

B) Connection to air gap then to the trap

THE HIGH LOOP

The high loop is necessary for proper draining. Therefore, all

ASKO dishwashers have the drain hoses attached to the drain pump and fastened to the top back of the unit, as illustrated. This gives the drain hose an automatic high loop, which is necessary for proper draining. The drain hose is fastened at the best high loop height.

To eliminate potential drain problems, simply leave this hose in place.

DO NOT REMOVE THE HIGH LOOP ATTACHED TO

THE BACK OF THE DISHWASHER!

24 ″ min.

(610 mm)

20 ″ min.

(508 mm)

IMPORTANT THINGS TO REMEMBER:

• Failure to provide the proper drain connection height (minimum of 20˝ (508 mm) above the bottom of the dishwasher base) or a 20˝ (508 mm) high loop will result in improper drainage, which will damage the machine.

• No part of the drain hose should be higher than

35˝ (889 mm) from the bottom of the dishwasher.

• The drain hose can be extended to a maximum length of 10 feet (3048 mm). Joints and jointed tubes, if any, must have a minimum 7/8˝ (22 mm) OD.

• If the drain line is going to be connected to a waste disposer, be sure to remove the knockout or plug from the fitting on the disposer before connecting the drain line.

• Do not use fittings smaller than 7/8˝ (22 mm)

OD; otherwise the water may not drain properly.

C) Connection to waste disposer with air gap

24 ″ min.

(610 mm)

20

″ min.

(508 mm)

NOTE:

Don’t forget to remove the knockout or plug from the disposer fitting.

12



2016-05-31 10:32:50


13



2. CONNECT WATER SUPPLY HOSE

WARNING!

Plumbing connections must comply with applicable sanitary, safety and plumbing codes in your area

.

The machine can be connected to either a hot

(max. 160 °F, 70 °C) or cold water supply. We recommend a cold water supply. The water pressure should be 4.2-140 psi.

Connect to cold water...

If you use oil or electricity to heat your home.

Connect to hot water (max 160 °F, 70 °C)...

If you use district heating, solar power, or geothermal power to heat your home. Choosing a hot water connection cuts program times and reduces the dishwasher’s electricity consumption.

For service convenience, a shut-off valve (not supplied) should be installed in the supply line in an easily accessible location, such as, beneath the sink.

In order to prevent heat damage to the inlet valve, all solder connections must be made before the water supply line is connected.

Flush the water supply line prior to connecting it to the water fill tube.

The unit has a float switch in the base pan to protect against flooding. If the inlet valve connection is not seated properly, water may leak into the base pan and activate the float switch.

Water connection should be carried out by a qualified professional. It is important that the water supply line and the shut-off valve have a sufficient flow volume. At least 3 gallons (12 liters) per minute must be able to pass through the line. Connect the machine using the accompanying supply hose.

Water pressure should be 4.2-140 PSI. There should be a shut off valve on the water pipe.

Use the supplied O ring and tighten the connection by hand plus a quarter turn with a wrench.

If the pipes are newly installed, it may be wise to flush them so that any debris is washed away. Otherwise, debris can clog the filter in the machine’s water intake and cut off the water supply.

Only use the inlet hose supplied with the machine.

Do not reuse old or other loose inlet hoses.

Shutoff valve

Grounded outlet

(1) Water supply

(2) Water supply valve (not supplied)

Water connection

(2)

(1)

NOTE:

Be sure to run the PEX tubing through the hole leading to the sink compartment before moving the dishwasher into position.



13

2016-05-31 10:32:50


3. CONNECT THE PLUG

Ensure that the power outlet is within the range of the power cable. Do not use an extension cord!

The dishwasher must be connected to a grounded outlet.

Grounded outlet

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grouding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grouded in accordance with all local codes and ordinances.

WARNING!

Improper connection of the equipmentgrounding conductor can result in a risk of electric shock. Check with a qualified electrican or service representative if you are in doubt whether the appliance is properly grounded.

Do not modify the plug provided with the appliance, if it will not fit the outlet, have proper outlet installed by a qualified electrician.

Plug

14



2016-05-31 10:32:51


15


STEP 5. CHECKING DISHWASHER FUNCTION AND FIT

Test the dishwasher with the Rinse & Hold program.

Check that the dishwasher fills and drains properly.

Also check that none of the connections leak.

Also check that adjacent drawers and cabinet doors can be opened when the dishwasher door is open.

STEP 6. SECURING THE DISHWASHER

A minimum 3 ½” (89 mm) finished return is required on all sides of the opening. Framed cabinets will require additional finished filler material behind the face frame for a proper installation. See illustration.

NOTE:

3 ½” (89 mm) finished returns will be visible and should be finished to match cabinetry.

3

/

4

”

(19)

TYPICAL

RETURN

W

FRAMELESS CABINETRY

1. Pull out the upper basket, and the center basket if present, and turn the basket stop on the runner outward.

2. To make more space available when installing the machine, remove the upper and center basket if present.

3. Remove the lower basket. Otherwise it easily rolls out if you need to adjust the dishwasher during installation.

4. Screw the dishwasher to the counter from the inside or to the cabinets on either side. If the counter is a hard material, such as marble, screw the dishwasher to the side cabinets. Use the supplied plastic spacers when mounting the dishwasher into place!

Alt. 1

5

6

NOTE:

When it is not possible to attach the dishwasher to the cabinet or the underside of the counter top, you should install tip guards to prevent the machine from tipping when you open the door.

Sold individually.

Alt. 2

FILLER

RETURN

W

FRAMED CABINETRY

5

6

Tip Guards

(P/N 441487)



15

2016-05-31 10:32:51

STEP 6. SECURING THE DISHWASHER

5. Check that the dishwasher’s steel feet are solidly placed on the floor. Make sure the dishwasher is not hanging in the air by the mounting tabs. If it is, turn the front feet to lower them until the machine is resting on the feet.

6. Also adjust the dishwasher’s steel feet so that the dishwasher is level.

7. Tighten the lock nuts on the steel feet with a 5/8 inch (16 mm) open-ended wrench.

5/8" (16 mm)

16



2016-05-31 10:32:52


17


*

1

*

2

3

5

6

4

6x

1-1/2"

(38 mm)

2x

3/8"

(10 mm)

2x 2x

1"

(25 mm)

STEP 7. ATTACHING THE TOE KICK (IF APPLICABLE)

*

7

7

*

8

8

Insulation material

1.

4.

5. x

6. x

2.

3.



17

2016-05-31 10:32:54

NOTES

18



2016-05-31 10:32:55


19

NOTES




19

2016-05-31 10:32:55

INSTALLATION CHECKLIST

ASKO - DISHWASHER

Appliance Installation Checklist

• Remove packaging and check for cosmetic damages.

• Remove the information packets from inside the dishwasher.

• Attach any accessories as required by the installation. Fill strips, light shielding film, supplied door sealing, accessory door, custom panel...

• Attach the drain line using the largest section of the disposer boot allowable.

Leave the high loop in place.

• Attach the PEX fill hose. Don’t forget to use the O-ring.

• Plug the dishwasher into the wall.

• Turn on the water and check the fill line connections for leaks.

• Slide the unit into the cabinet and level the machine front to rear, and left to right.

• Mount the unit to the cabinet.

• Show the customer their warranty card, and help them locate the model and serial number on the unit.

• Leave all user books for consumer.

20



en (05-16)

2016-05-31 10:32:55

Asko ADA series Installation Instructions Manual

Installation Instructions

FI Dishwasher

CONTENTS

IMPORTANT!

INTRODUCTION

WHAT YOU NEED

SAFETY INSTRUCTIONS

BEFORE STARTING THE INSTALLATION

XXL/XL?

XXL DISHWASHERS

ADA AND XL DISHWASHERS

STEP 1. FITTING THE DISHWASHER IN PLACE

STEP 1. FITTING THE DISHWASHER IN PLACE

STEP 1. FITTING THE DISHWASHER IN PLACE

STEP 2. ATTACHING THE ACCESSORY DOOR OR CUSTOM PANEL

STEP 3. ADJUSTING THE DOOR SPRINGS

STEP 4. CONNECTING ELECTRICITY, WATER, AND DRAIN

STEP 4. CONNECTING ELECTRICITY, WATER, AND DRAIN

STEP 4. CONNECTING ELECTRICITY, WATER, AND DRAIN

STEP 5. CHECKING DISHWASHER FUNCTION AND FIT

STEP 6. SECURING THE DISHWASHER

STEP 6. SECURING THE DISHWASHER

STEP 7. ATTACHING THE TOE KICK (IF APPLICABLE)

NOTES

NOTES

INSTALLATION CHECKLIST

ASKO - DISHWASHER

Related manuals

Table of contents

Asko ADA series Installation Instructions Manual

Installation Instructions

FI Dishwasher

CONTENTS

IMPORTANT!

INTRODUCTION

WHAT YOU NEED

SAFETY INSTRUCTIONS

BEFORE STARTING THE INSTALLATION

XXL/XL?

XXL DISHWASHERS

ADA AND XL DISHWASHERS

STEP 1. FITTING THE DISHWASHER IN PLACE

STEP 1. FITTING THE DISHWASHER IN PLACE

STEP 1. FITTING THE DISHWASHER IN PLACE

STEP 2. ATTACHING THE ACCESSORY DOOR OR CUSTOM PANEL

STEP 3. ADJUSTING THE DOOR SPRINGS

STEP 4. CONNECTING ELECTRICITY, WATER, AND DRAIN

STEP 4. CONNECTING ELECTRICITY, WATER, AND DRAIN

STEP 4. CONNECTING ELECTRICITY, WATER, AND DRAIN

STEP 5. CHECKING DISHWASHER FUNCTION AND FIT

STEP 6. SECURING THE DISHWASHER

STEP 6. SECURING THE DISHWASHER

STEP 7. ATTACHING THE TOE KICK (IF APPLICABLE)

NOTES

NOTES

INSTALLATION CHECKLIST

ASKO - DISHWASHER

Related manuals

Atag

VA9611NT

Asko

491289

Asko

492632

Asko

D5534XLFI

Asko

492612

Asko

DFI664XXLSOF

Asko

DFI663

Asko

DFI663XXL

Asko

DBI664IXXLSSOF

Asko

DBI663IS

Table of contents