Manual Water Softener

Manual Water Softener
MANUAL WATER
SOFTENER RANGE
Technical data
Table 1
Water
hardness
Model
degrees French
30 °f
40 °f
60 °f
80 °f
degrees German
16.5 °d
22 °d
33 °d
44 °d
Parts per million
300 ppm
400 ppm
600 ppm
800 ppm
Height
Salt
WS - 08
1000 ltrs
900 ltrs
700 ltrs
500 ltrs
400 mm
1.0 kg
WS - 12
1500 ltrs
1350 ltrs
1050 ltrs
750 ltrs
500 mm
1.5 kg
WS - 16
2100 ltrs
1800 ltrs
1400 ltrs
1000 ltrs
600 mm
2.0 kg
WS - 20
3000 ltrs
2600 ltrs
2100 ltrs
1500 ltrs
900 mm
2.5 kg
Volume of water softened, against hardness
Flow rate
(litres per hour)
1000 ltrs
Water pressure
Water temperature
Minimum
Maximum
Minimum
Maximum
1 bar
5.5 bar
4 °c
15 °c
This leaflet is an integral part of the product. Please read the warnings provided carefully as these
provide important information concerning the safe installation, use and servicing of this product. This
water softener is intended to be used to soften cold drinking water only, any other use is considered
improper and as such unreasonable.
WARNING: use only sodium chloride Na Cl in large grains (kitchen salt) for regeneration. The
use of any other chemical substances or products is strictly forbidden.
Figure 1 LEGEND
A. Water Inlet
B. Water Outlet
C. Water Inlet Tap
D. Water Outlet
E. Pressure Relief Hose
F. Regeneration Hose
G. Cover Knob
I. Check Valve Tap
Fig 1: Installation Drawing
INSTALLATION.
After removing the packaging, make sure that the water softener isn't damaged. Keep the packaging
materials (plastic bags, cardboard box etc.) out of the reach of children as they can be dangerous.
The water softener should be installed in full observance of the current laws, following the
manufacturer's instructions and by experts. If installed incorrectly, the equipment may cause injuries
to people and animals and damage to property, in which case the manufacturer cannot be held
liable.
• Install the water softener in rooms where the temperature is minimum 5°c and maximum 30°c
CONNECTION TO THE WATER MAINS (Refer to Fig 1)
• The user must install a tap between the water mains and the water softener so that the water can
be turned off in an emergency, plus a check valve to avoid any pressure returns.
• Connect the water inlet and outlet hoses to the water softener and make sure these are tightened
properly.
• Place the drain hose directly in a drain.
COMMISSIONING
Fig 2
Rinsing of resins (Refer to Fig 2) Place the
outlet hose in a drain.
Turn the taps levers to the left and open the water inlet; let the water flow
until clear, then stop the inlet water and connect the outlet hose to the
machine to be supplied.
Routine Regeneration (Refer to Fig 3)
Fig 3
• Place the depression hose in a bucket. Turn the taps levers to the right and
wait for the pressure to drop. Remove the cover by unscrewing the knob and
then add the salt in the amount indicated to suit the model (see table 1).
• WARNING: Remove any salt from the seal on the cover.
Regeneration Mode (Refer to Fig 4)
Fig 4
• Replace the cover and tighten the knob securely, then move the inlet tap
lever to the left.
• WARNING: Remove any salt from the top of the water softener.
• Let the salty water flow from the drain hose until the water is soft (about 40
minutes).
Normal Operating Mode
Fig 5
• Return the water softener to normal working conditions by turning the outlet
tap lever to the left.
• Regeneration completed.
• WARNING: the equipment connected to the water softener is not
supplied during regeneration.
To ensure the efficiency of the water softener at all times, we recommend routine
regeneration to suit the use made of the water softener and the hardness of the water used.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement