Service Manual - Daewoo
S/M No. : C621Q0S002
Service Manual
Microwave Oven
Model: KOC-621Q0S
KOC-624Q0S
DAEWOO ELECTRONICS CO., LTD.
http : //svc.dwe.co.kr
Feb. 2002
PRECAUTIONS TO BE OBSERVED BEFORE AND
DURING SERVICING TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
(a) Do not operate or allow the oven to be operated with the door open.
(b) Make the following safety checks on all ovens to be serviced before activating the magnetron or other
microwave source, and make repairs if necessary: (1) Interlock operation, (2) Proper door closing, (3)
Seal and sealing surfaces (arcing, wear, and other damage), (4) Damage to or loosening of hinges and
latches (5) Evidence of dropping or abuse.
(c) Before turning on power to the microwave oven for any service test or inspection within the microwave
generating compartments, check the magnetron, wave guide or transmission line, and cavity for proper
alignment, integrity, and connections.
(d) Any defective or misadjusted components in the interlock, monitor, door seal and microwave
generation and transmission systems shall be repaired, replaced, or adjusted by procedures described
in this manual before the oven is released to the owner.
A microwave leakage check to verify compliance with the Federal performance standard should be
performed on each oven prior to release to the owner.
TABLE OF CONTENTS
1. SAFETY AND PRECAUTIONS....................................................................................................................................2
2. SPECIFICATIONS ........................................................................................................................................................3
3. EXTERNAL VIEW.........................................................................................................................................................3
3-1. OUTER DIMENSION ..........................................................................................................................................3
3-2. FEATURE DIAGRAM .........................................................................................................................................4
4. INSTALLATION ............................................................................................................................................................5
5. CONTROL PANEL .......................................................................................................................................................6
6. DISASSEMBLY AND ASSEMBLY ..............................................................................................................................8
7. INTERLOCK MECHANISM AND ADJUSTMENT.....................................................................................................19
8. TROUBLE SHOOTING GUIDE ..................................................................................................................................20
9. MEASUREMENT AND TEST.....................................................................................................................................26
9-1. MEASUREMENT OF THE MICROWAVE POWER OUTPUT ........................................................................26
9-2. MICROWAVE RADIATION TEST ....................................................................................................................27
9-3. COMPONENT TEST PROCEDURE................................................................................................................28
9-4. COMPONENT ACTION....................................................................................................................................29
10. WIRING DIAGRAM...................................................................................................................................................30
11. EXPLODED VIEW AND PARTS LIST ..................................................................................................................31
11-1. DOOR ASSEMBLY.........................................................................................................................................31
12-2. CONTROL PANEL ASSEMBLY.....................................................................................................................31
13-3. TOTAL ASSEMBLY ........................................................................................................................................31
12. PRINTED CIRCUIT BOARD ....................................................................................................................................33
13. P.C.B CIRCUIT DIAGRAM.......................................................................................................................................37
1
1. SAFETY AND PRECAUTIONS
1. FOR SAFE OPERATION
Damage that allows the microwave energy (that cooks or heats the food) to escape will result in poor cooking and may
cause serious bodily injury to the operator.
IF ANY OF THE FOLLOWING CONDITIONS EXIST, OPERATOR MUST NOT USE THE APPLIANCE.
(Only a trained service personnel should make repairs.)
(1) A broken door hinge.
(2) A broken door viewing screen.
(3) A broken front panel, oven cavity.
(4) A loosened door lock.
(5) A broken door lock.
The door gasket plate and oven cavity surface should be kept clean.
No grease, soil or spatter should be allowed to build up on these surfaces or inside the oven.
DO NOT ATTEMPT TO OPERATE THIS APPLIANCE WITH THE DOOR OPEN.
The microwave oven has concealed switches to make sure the power is turned off when the door is opened.
Do not attempt to defeat them.
DO NOT ATTEMPT TO SERVICE THIS APPLIANCE UNTIL YOU HAVE READ THIS SERVICE MANUAL.
2. FOR SAFE SERVICE PROCEDURES.
1. If the oven is operative prior to servicing, a microwave emission check should be performed prior to servicing the
oven.
2. If any certified oven unit is found to servicing, a microwave emission check should be performed prior to servicing the
oven.
(1) inform the manufacturer, importer or assembler,
(2) repair the unit at no cost to the owner,
(3) attempt to ascertain the cause of the excessive leakage,
(4) tell the owner of the unit not to use the unit until the oven has been brought into compliance.
3. If the oven operates with the door open, the service person should tell the user not to operate the oven and contact
the manufacturer immediately.
IMPORTANT
The wire in this mains lead coloured in accordance with the following code.
Green-and-yellow : Earth
Blue
: Neutral
Brown
: Live
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked with the
letter ‘E’, earth symbol or coloured green-and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the letter ‘N’ or coloured
black.
The wire which is coloured brown must be connected to the terminal which is marked with the letter ‘L’ or coloured
red.
NOTE : This oven is designed for counter-top use only.
2
2. SPECIFICATIONS
MODEL
KOC-621Q0S, 624Q0S
POWER SUPPLY
MICROWAVE
230V~50HZ, SINGLE PHASE WITH EARTHING
1250W
POWER
GRILL
1250W
CONSUMPTION
OVEN
1650W
COMBINATION
2500W
MICROWAVE ENERGY OUTPUT
800W(IEC705)
MICROWAVE FREQUENCY
2450MHz
OUTSIDE DIMENSIONS (W X H X D)
470X285X356mm (18.5X11.2X14.0 in.)
CAVITY DIMENSIONS (W X H X D)
295X167X300mm (11.6X6.6X11.8 in.)
NET WEIGHT
APPROX. 15kg (33.1 lbs.)
TIMER
Oven: 99 minutes, M/W: 60 minutes, Grill: 30 minutes
FUNCTION SELECTIONS
MICROWAVE/ GRILL/ OVEN/ COMBINATION
POWER SELECTIONS
10 LEVELS
CAVITY VOLUME
0.6 Cu. Ft
* Specifications are subject to change without notice.
3. EXTERNAL VIEW
OUTER DIMENSION
470
356
285
3-1.
3
3-2. FEATURE DIAGRAM
1
2
3
4 5
M/W
Def.
Grill
Temp
g
Auto Cook
1. Roast Beef
3. Roast Chicken
5. Vegetable
2. Roast Pork
4. Fish Fillets
M/W
Defrost
Grill
1000g
Combi
100g
10m.
1m.
Temp
10s.
Clock
Auto Cook
6
Start/
Speedy cook
Stop/
Clear
Combi
KOC-621Q
e
w
q 7
8
9
0
11.DOOR HOOK
When the door is closed, it will automatically lock shut. If door is opened while oven is operating, the magnetron
will immediately stop operating.
12.DOOR VIEWING SCREEN
Allows viewing of food. The screen is designed so that light can pass through, but not the microwave.
13.TOP HEATER
Turns on when convection, grill and combi cooking is selected.
14.OVEN LAMP
Automatically turns on during oven operating.
15.SAFETY INTERLOCK SYSTEM
16.CONTROL PANEL
17. UNDER HEATER
18. METAL RACK
19.TURNTABLE TRAY
Rotates during cooking and ensure even distribution of Microwaves.
It can also be used as a cooking utensil.
10.TRAY GUIDE
This must always be used for cooking together with the turntable tray.
11. COUPLER
This fits over the shaft in the center of the ovens cavity floor. This is to remain in the oven for all cooking.
12. OVEN FRONT PLATE
13.DOOR SEAL
Door seal maintains the microwave energy within the oven cavity and prevents microwave leakage.
4
4. INSTALLATION
1. Steady, flat location
This microwave oven should be set on a steady, flat surface.
This microwave oven is designed for counter top use only.
2. Leave space behind and side
All air vents should be kept a clearance. If all vents are covered during operation, the oven may overheat and, eventually,
cause failure.
3. Away from Radio and TV sets
Poor television reception and radio interference may result if the oven is located close to a TV, Radio, antenna or feeder
and so on.
Position the oven as far from them as possible.
4. Away from heating appliances and water taps
Keep the oven away from hot air, steam or splash when choosing a place to position it, or the insulation might be
adversely affected and breakdowns occur.
5. Power supply
• Check your local power source. This microwave oven requires a current of approximately 12 amperes, 230V, 50Hz.
• Power supply cord is about 1.2 meters long.
• The voltage used must be the same as specified on this oven. Using a higher voltage may result in a fire or other
accident causing oven damage. Using low voltage will cause slow cooking. We are not responsible for damage
resulting from use of this oven with a voltage of ampere fuse other than those specified.
• This appliance is supplied with cable of special type, which, if damaged, must be repaired with cable of same type.
• Such a cable can be purchased from DAEWOO and must be installed by a Qualified Person.
6. Examine the oven after unpacking for any damage such as:
A misaligned door, broken door or a dent in cavity.
If any of the above are visible, DO NOT INSTALL, and notify dealer immediately.
7. Do not operate the oven if it is colder than room temperature.
(This may occur during delivery in cold weather.) Allow the oven to become room temperature before operating.
EARTHING INSTRUCTIONS
This appliance must be earthed. In the event of an electrical short circuit, earthing reduces the risk of the electric shock by
providing an escape wire for the electric current. This appliance is equipped with a cord having a earthing wire with a
earthing plug. The plug must be plugged into an outlet that is properly installed and earthed.
WARNING
Improper use of the earthing plug can result in a risk of electric shock.
Consult a qualified electrician of serviceman if the earthing instructions are not completely understood, or if doubt
exists as to whether the appliance is properly earthed, and either:
If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 3-blade earthing plug, and a
3-slot receptacle that will accept the plug on the appliance.
The marked rating of the extension cord should be equal to or greater than the electrical rating of the appliance, or
Do not use an extension cord.
5
5. CONTROL PANEL
1. KOC-621Q0S
M/W
Def.
Grill
Temp
g
Auto Cook
1. Roast Beef
3. Roast Chicken
5. Vegetable
2. Roast Pork
4. Fish Fillets
1
M/W
3
Grill
1000g
10m.
6
4
Combi
100g
1m.
7
5
Temp
10s.
8
9
Clock
Auto Cook
0
q
Stop/
Clear
Start/
Speedy cook
w
Defrost
2
Combi
KOC-621Q
BUTTONS
1. m/w - Press to select microwave power level.
2. defrost - Press to select weight/time defrost mode.
3. grill - Press to select grill.
4. combi - Press to select combi cooking mode.
5. temp - Press to select temperature.
6. 10m. - Press to set time and weight.
7. 1m. - Press to set time and weight.
8. 10s. - Press to set time.
9. clock - Use to set clock.
10. auto cook - Press to select auto cook menu.
11. stop/clear - Press once to stop a programme, and twice to cancel a programme.
12. start/speedy cook - Press to start a programme, also for speedy start (each press adds 30 seconds microwave
cooking time).
6
2. KOC-624Q0S
M/W
Def.
Grill Temp
g
Auto Cook
1. Roast Beef
2. Roast Pork
3. Roast Chicken 4. Fish Fillets
5. Vegetable
1
M/W
Defrost
2
3
Grill
10min.
6
4
Combi
1min.
7
5
Temp
10sec.
8
9
Clock
Auto Cook
0
q
Stop/
Clear
Start/
Speedy cook
w
BUTTONS
1. m/w - Press to select microwave power level.
2. defrost - Press to select weight/time defrost mode.
3. grill - Press to select grill.
4. combi - Press to select combi cooking mode.
5. temp - Press to select temperature.
6. 10m. - Press to set time and weight.
7. 1m. - Press to set time and weight.
8. 10s. - Press to set time.
9. clock - Use to set clock.
10. auto cook - Press to select auto cook menu.
11. stop/clear - Press once to stop a programme, and twice to cancel a programme.
12. start/speedy cook - Press to start a programme, also for speedy start (each press adds 30 seconds microwave
cooking time).
7
6. DISASSEMBLY AND ASSEMBLY
- Cautions to be observed when trouble shooting.
Unlike many other appliances, the microwave oven is high-voltage, high-current equipment. It is completely safe
during normal operation. However, carelessness in servicing the oven can result in an electric shock or possible
danger from a short circuit. You are asked to observe the following precautions carefully.
1. Always remove the power plug from the outlet before servicing.
2. Use an insulated screwdriver and wear rubber gloves when servicing the high voltage side.
3. Discharge the high voltage capacitor before touching any oven components or wiring.
(1) Check the grounding.
Do not operate on a two-wire extension cord.
The microwave oven is designed to be used while grounded.
It is imperative, therefore, to make sure it is grounded
properly before beginning repair work.
(2) Warning about the electric charge in the high voltage capacitor.
For about 30 seconds after the operation has stopped, electric
charge remains in the high voltage capacitor.
When replacing or checking parts, short between oven chassis
and the negative high terminal of the high voltage capacitor by
using a properly insulated screwdriver to discharge.
4. When the 15A fuse is blown out due to the operation of the monitor
switch; replace primary interlock switch, secondary interlock switch
and interlock monitor switch.
5. After repair or replacement of parts, make sure that the screws are
properly tightened, and all electrical connections are tightened.
6. Do not operate without cabinet.
SHORT
CAUTION : Service personnel should remove their watches whenever working close to or replacing the magnetron.
WARNING : When servicing the appliance, take care when touching or replacing high potential parts because of
electrical shock or exposing microwave. These parts are as follows - HV Transformer, Magnetron,
HV Capacitor, HV Diode.
8
1. To remove cabinet
1) Remove four screws on cabinet back.
2) Push the cabinet backward.
2. To remove door assembly
1) Remove two screws which secure the stopper hinge top.
2) Remove the door assembly from top plate of cavity.
3) Reverse the above for assemby.
NOTE: After replacting the door assembly, perform a
check of correct alignment with the hinge and
cavity front plate.
9
3. To remove door parts.
• KOC-621Q0S
REF NO.
PART CODE
A01
3512203410
FRAME DOOR
PART NAME
ABS
DESCRIPTION
1
A02
3517004800
BARRIER-SCREEN *O
TEMP GLASS T3.2
1
A03
3515203000
STOPPER HINGE *T AS
KOC-621S5J
1
A04
3511709400
DOOR PAINTING AS
KOC-621S5J
1
A05
3517004700
BARRIER-SCREEN *I
TEMP GLASS T3.0
1
A06
3512301100
GASKET DOOR
PBT
1
A07
3513101000
HOOK
POM
1
A08
3515101700
SPRING HOOK
PW1
1
(1) Remove the gasket door(A06) from door plate.
(2) Remove the door frame (A01) from door plate(A04).
(3) Remove the stopper hinge top(A03) from door plate(A04).
(4) Remove the spring(A08) and the hook(A07).
(5) Remove the barrier screen outer(A02) from door frame(A01).
(6) Reverse the above steps for reassembly.
10
Q’TY
REMARK
• KOC-624Q0S
A03
A04
A01
A07
A02
A08
A11
A05
A10
A06
A09
A12
A13
A15
A14
REF NO.
PART CODE
PART NAME
DESCRIPTION
A01
3512301100
GASKET DOOR
PBT
1
A02
3517004700
BARRIER-SCREEN *I
TEMP GLASS T3.0
1
A03
3515203000
STOPPER HINGE *T AS
KOC-621S5J
1
A04
3511709400
DOOR PAINTING AS
KOC-621S5J
1
A05
3513101000
HOOK
POM
1
A06
3515101700
SPRING HOOK
PW1
1
A07
3517004800
BARRIER SCREEN *O
TEMP GLASS T3.2
1
A08
3512203420
FRAME DOOR
ABS
1
A09
7001503511
SCREW MACHINE
PAN 5*35 MFZN
2
A10
3511606500
DECORATOR DOOR *T
SUS430
1
A11
3511606800
DECORATOR DOOR *L
SUS430
1
A12
3511606600
DECORATOR DOOR *U
SUS430
1
A13
3511606700
DECORATOR DOOR *R
SUS430
1
A14
3515307800
SUPPORTER HANDLE
KOR-164H0A
2
A15
3512603210
HANDEL DOOR
KOC-624’X
1
(1) Remove the gasket door(A01) from door plate.
(2) Remove the door frame (A08) from door plate.
(3) Remove two screws (A09) from door plate.
(4) Remove the door handle (A15) and handle supporter (A14) from door plate.
(5) Remove the four door decorators (A10~A13) from door frame.
(6) Remove the stopper hinge top(A03) from door plate.
(7) Remove the spring(A06) and the hook(A05).
(8) Remove the barrier screen outer(A07) from door frame.
(9) Reverse the above steps for reassembly.
11
Q’TY
REMARK
4. Method to reduce the gap between the door seal and the
oven front surface.
A
(1) To reduce gap located on part ‘A’.
• Loosen two screws on stopper hinge top, and then push the door
to contact the door seal to oven front surface.
• Tighten two screws.
M/W
Def.
Grill
Temp
2. Roast Pork
4. Fish Fillets
M/W
Defrost
Grill
1000g
Combi
100g
Auto Cook
Start/
Speedy cook
KOC-621Q
NOTE : A small gap may be acceptable if the microwave leakage does not exceed 4mW/cm2.
12
1m.
10s.
Clock
Combi
B
10m.
Temp
Stop/
Clear
(2) To reduce gap located on part ‘B’.
• Loosen two screws on stopper hinge under, and then push the
door to contact the door seal to oven front surface.
• Tighten two screws.
g
Auto Cook
1. Roast Beef
3. Roast Chicken
5. Vegetable
5. To remove control panel parts.
• KOC-621Q0S
REF NO.
PART CODE
B01
3518523500
SWITCH MEMBRANE
PART NAME
KOC-621Q0S
DESCRIPTION
1
B02
3516715810
CONTROL-PANEL
ABS
1
B03
3514325720
PCB AS
KOC-621Q0S
1
B04
7112401211
SCREW TAPPING
T1 TRS 4X12 MFZN
4
(1) Remove four screws(B04) which secure the PCB AS(B03).
(2) Pull out the PCB AS(B03) from control panel(B02).
(3) Reverse the above steps for reassembly.
13
Q’TY
REMARK
• KOC-624Q0S
B03
B04
B02
B05
B01
REF NO.
PART CODE
PART NAME
DESCRIPTION
Q’TY
B01
3518523510
SWITCH MEMBRANE
KOC-624Q0S
1
B02
3511606900
DECORATOR C-PANEL
SUS430
1
B03
3516715830
CONTROL PANEL
ABS
1
B04
PKMPMSEQ30
PCB MAIN MANUAL AS
KOC-624Q0S
1
B05
7112401211
SCREW TAPPING
T2S TRS 4*12 MFZN
4
REMARK
(1) Remove the screw which secure the control panel, push up two snap fits and draw forward the control panel
assembly.
(2) Remove four screws which secure the PCB assembly to control panel.
(3) Disconnect membrane tail from the connector of the PCB assembly.
(4) Detach membrane from the control panel.
(5) Pull out the decorator c-panel from the control panel.
(6) Reverse the above steps for reassembly.
14
6. To remove high voltage capacitor.
1) Remove a screw which secure the grounding ring
terminal of the H.V. diode and the capacitor holder.
2) Remove the H.V. diode from the capacitor holder.
3) Reverse the above steps for reassembly.
◆ High voltage circuit wiring
7. To remove magnetron.
1) Remove a screw which secure the magnetron.
2) Remove the magnetron.
3) Reverse the above steps for reassembly.
CAUTION : Never install the magnetron without the metallic gasket plate which is packed with each magnetron to
prevent microwave leakage. Whenever repair work is carried out on magnetron, check the microwave
leakage. It shall not exceed 4mW/cm2 for a fully assembled oven with door normally closed.
Metallic
gasket
plate
Magnetron
antenna
Cooling fin
Filament
terminal
15
8. To remove wind guide assembly.
1) Remove a screw for earthing.
2) Remove the noise filter from the wind guide.
3) Remove two screws which secure the wind guide assembly.
4) Draw forward the wind guide assembly.
5) Pull the fan from the motor shaft.
6) Remove two screws which secure the motor shaded pole.
7) Remove the motor shaded pole.
8) Reverse the above steps for reasembly.
9. To remove H.V.transformer.
1) Remove four screws holding the H.V.transformer.
2) Remove the H.V.transformer.
3) Reverse the above steps for reassembly.
16
10. To remove Top heater assembly parts.
REF NO.
1
2
3
4
5
6
PART CODE
7112401011
3511409700
3512513110
7392500011
7392500011
3512803300
PART NAME
SCREW TAPPING
COVER INSU *T AS
GUIDE AIR OUTLET
NUT HEX
NUT HEX
HEATER
DESCRIPTION
T1 TRS 4*10 MFZN
KOC-621Q0S
SA1D-80 T0.5
6N-2-5 MFZN
6N-2-5 MFZN
230V 1150W 1B08965
1) Remove two screws 1 then pull out cover insulator *t as 2 and guide air outlet 3.
2) Remove a hex nut 4 and hex nut 5.
3) Pull out heater.
4) Reverse the above steps for reassembly.
17
Q’TY
2
1
1
1
1
1
REMARK
11. To remove Motor synchro. And Under heater assembly parts.
CUTTING (8EA)
REF NO.
1
2
3
4
5
PART CODE
7122400811
7113400814
3512802000
3515304000
3511404410
PART NAME
SCREW TAPPING
SCREW TAPPING
HEATER *U
SUPPORTER HEATER
COVER HEATER *U
DESCRIPTION
T2S TRS 4*8 MFZN
T1 BIN 4*8 MFNI
230V 400W R1837400
STS430 T0.5
STS430-2B/HL T0.6
1) Cut the cover parts from the base plate.
2) Remove a screw and then pull out Motor syncro.
3) Remove a screw1 and then pull out the Under heater *U. assembly.
4) Remove a screw2 .
5) Pull out the Heater *U 3 from the Cover heater *U 5 .
6) Reverse the above steps for reassembly.
18
Q’TY
1
1
1
1
1
REMARK
7. INTERLOCK MECHANISM AND ADJUSTMENT
The door lock mechanism is a device which has been specially designed to completely eliminate microwave radiation when
the door is opened during operation, and thus to perfectly prevent the danger resulting from the leakage of microwave.
(1) Primary interlock switch
When the door is closed, the hook locks the oven door. If the door is not closed properly, the oven will not operate.
When the door is closed, the hook pushes the button of the microswitch. Then the button of the primary interlock switch
bring it under ON condition.
(2) Secondary interlock switch and interlock monitor switch
When the door is closed, the hook pushes the lock lever downward. The lock lever presses the button of the interlock
monitor switch to bring it under OFF condition and presses the button of the secondary interlock switch to bring it under
ON condition.
ADJUSTMENT :
Interlock monitor switch
When the door is closed, the interlock monitor switch should be opened before other switches are closed.
When the door is opened, the interlock monitor switch should be closed after other switches are opened.
(3) Adjustment steps
a) Loosen the two mounting screws.
b) Adjust interlock switch assembly position.
c) Make sure that lock lever moves smoothly after adjustment is completed.
d) Tighten completely two mounting screws.
NOTE :
Microwave emission test should be performed after adjusting interlock mechanism.
If the microwave emission exceed 4mW/cm2, readjust interlock mechanism.
19
8. TROUBLE SHOOTING GUIDE
Following the procedure below to check if the oven is defective or not.
1) Check grounding before trouble checking.
2) Be careful of the high voltage circuit.
3) Discharge the high voltage capacitor.
4) When checking the continuity of the switches, fuse or high voltage tranformer, disconnect one load wire from these
parts and check continuity with the AC plug removed. To do otherwise may result in a false reading or damage to
your meter.
NOTE : When electric parts are checked, be sure the power cord is not inserted the wall outlet.
Check wire harness, wiring and connection of the terminals and power cord before check the parts listed below.
(TROUBLE 1) Oven does not operate at all : any inputs can not be accepted.
CONDITION
Fuse blows.
CHECK
Check continuity of
interlock monitor switch with
door closed
( COM↔NC )
RESULT
CAUSE
Continuity
Malfunction of
Interlock
monitor switch
(COM↔NC)
REMEDY
Replace
No continuity
No
Continuity
Check continuity of
both primary and secondary
interlock switch with door closed
Malfunction of
interlock switch
Replace
Continuity
Continuity
Check continuity of
primary interlock switch contact with
door partially open until interlock
monitor switch contact close
( COM↔NC close )
Check continuity of
primary winding of low voltage
transformer
0 Ω or infinite
Approx.
790Ω
( normal )
Fuse again
blows
Disconnect high voltage
fuse and operate the unit
20
Shorted contacts
of primary
interlock Switch
Defective low
voltage
transformer
Defective
high voltage
transformer
Replace
Replace
Replace
CONDITION
CHECK
RESULT
CAUSE
REMEDY
Outlet has
proper
voltage
fuse does not
blow?
Check continuity of
magnetron
No
continuity
Defective
magnetron.
Replace
Check continuity of noise filter
board
No
continuity
Defective line
filter board
Replace
Check continuity of
power supply cord
No
continuity
Open power
supply cord
Replace
continuity
Defective touch
control circuit
Replace
NOTE : All these switches must be replaced at the same time, please refer to (7.Interlock mechanism and
adjustment) for adjustment instructions
(TROUBLE 2)
Display shows all figures selected, but oven does not start cooking, even though desired program and time
are set and start button is tapped.
CONDITION
CHECK
RESULT
CAUSE
REMEDY
Turn table
motor and
oven lamp
do
not turn on
Check continuity of
primary interlock switch
No
continuity
Malfunction of
primary interlock
switch
Adjust or
replace
Check continuity of
secondary interlock
and D.O.M switch
No
continuity
Malfunction of
secondary
Interlock and
D.O.M switch
Adjust or
replace
Check D.C voltage
being supplied to
RELAY(RY5) coil
0V
Defective touch
control Circuit
Replace
Approx.
13V DC
Fault contacts
of RELAY
(RY5) or open
relay coil.
Replace
21
TROUBLE 3) No microwave oscillation even though fan motor rotates.
CONDITION
CHECK
RESULT
CAUSE
REMEDY
No
microwave
oscillation
Check continuity of
high voltage fuse
No
continuity
Defective
high voltage
fuse
Replace
Check continuity of
high voltage capacitor terminals
with wires removed
Continuity
Defective
high voltage
transformer
1
Check continuity of
high voltage rectifier in forward
and backward
direction with DC megger
Continuity
in backward
direction
Defective high
voltage rectifier
Replace
No microwave oscillation
Connect megger leads to
magnetron terminal and
magnetron body
Continuity
Defective
magnetron
2
Check D.C voltage
being supplied to
RELAY (RY1) coil
0V
Defective
touch control
circuit
Replace
Approx.
13V DC
Faulty contacts of
RELAY
(RY1) or open
relay coil
Replace
Defective
high voltage
transformer
Replace
Defective high
voltage
transformer
Replace
Defective
magnetron
Replace
0 Ω or ∞
1 Check resistance of primary
and secondary coil of high
voltage transformer
1 Check continuity of filament
No continuity
terminal of high voltage
transformer
2 Check continuity of
magnetron heater with wires
removed
No continuity
22
(TROUBLE 4)
Grill heater (upper heater) is not heated; food will not become hot.
CONDITION
Grill heater is
not heated.
CHECK
RESULT
CAUSE
REMEDY
Check continuity of
primary interlock switch
No
continuity
Malfunction of
primary Interlock
switch
Adjust or
replace
Check continuity of
secondary interlock switch
No
continuity
Malfunction of
secondary
interlock switch
Adjust or
replace
Check continuity of
heater
No
continuity
Defective heater
Check D.C voltage
being supplied to
RELAY (RY3) coil
0V
Defective touch
control circuit
Replace
Approx.
13V DC
Faulty contacts of
RELAY
(RY3) or open
relay coil
Replace
Replace
(TROUBLE 5)
Fan motor does no rotate.
CONDITION
CHECK
RESULT
CAUSE
REMEDY
Fan does
not rotate.
Check continuity of
primary interlock switch
No
continuity
Malfunction of
primary Interlock
switch
Adjust or
replace
Check continuity of
secondary interlock
switch
No
continuity
Malfunction of
secondary
interlock switch
Adjust or
replace
Check continuity of
fan
No
continuity
Defective fan
Check D.C voltage
being supplied to
RELAY (RY6) coil
0V
Defective touch
control circuit
Replace
Approx.
13V DC
Faulty contacts of
RELAY
(RY6) or
open relay coil
Replace
23
Replace
(TROUBLE 6)
Lower heater is not heated; food will not become hot.
CONDITION
CHECK
RESULT
CAUSE
REMEDY
Lower heater
Is not heated
Check continuity of
Primary interlock switch
No
continuity
Malfunction of
primary Interlock
switch
Adjust or
Replace
Check continuity of
secondary interlock
switch
No
continuity
Malfunction of
secondary
interlock switch
Adjust or
replace
Check continuity of
heater
No
continuity
Defective heater
Check D.C voltage
Being supplied to
RELAY (RY4) coil
0V
Defective
Touch control
circuit
Replace
Approx.
13V DC
Faulty contacts of
RELAY
(RY4) or open
relay coil
Replace
Replace
(TROUBLE 7)
The following visual conditions indicate a probable defective touch control Circuit or Membrane.
1. Incomplete segments.
1) segment missing
2) partial segments missing
3) digit flickering other than normal fluorescent slight flickering
2. A distinct change in the brightness of one or more numbers exists in the
display
3. One or more digits in the display are not on when they should be.
4. Display does not count down or up with time cooking or clock operation.
5. Oven is programmable and cooks normally but no display shows.
6. Display obviously jumps in time while counting down.
M/W
Def.
Grill
Temp
7. Display counts down noticeably too fast while cooking.
CONDITION
CHECK
Display does
not show
programming
at all, even if
keyboard is
touched.
Check each pad for continuity
of the pad
RESULT
Normal
24
g
CAUSE
REMEDY
Malfunction of
Membrane.
Replace
C/PANEL
assembly.
(TROUBLE 8)
When “Err 2” or “Err 3” come on display.
CONDITION
CHECK
RESULT
CAUSE
REMEDY
“Err 2” or
“Err 3” come
on display
Check continuity of thermistor
(resistance of thermistor)
0Ω or infinite
Defective
thermistor
Replace
Approx
200k~300kΩ
(room
temperature)
Check continuity of heater
(upper, lower)
25
No
continuty
Defective
heater
Replace
continuity
Defective touch
control circuit
Replace
9. MEASUREMENT AND TEST
9-1. MEASUREMENT OF THE MICROWAVE POWER OUTPUT
Microwave output power can be checked by indirectly measuring the temperature rise of a certain amount of water
exposed to the microwave as directed below.
PROCEDURE
1. Microwave power output measurement is made with the microwave oven supplied at rated voltage and operated at
its maximum microwave power setting with a load of 1000 ± 5cc of potable water.
2. The water is contained in a cylindrical borosilicate glass vessel having a maximum material thickness of 3 mm and
an outside diameter of approximately 190 mm.
3. The oven and the empty vessel are at ambient temperature prior to the start of the test. The initial temperature of
the water is 10 ± 2°C (50 ± 3.6°F). If is measured immediately before the water is added to the vessel. After
addition of the water to the vessel, the load is immediately placed on the center of the shelf, which is in the lowest
normal position.
4. Microwave power is switched on.
5. Heating time should be exactly A seconds.
(Refer to table as following)
Heating time is measured while the microwave
generator is operating at full power. The filament heatup time for magnetron is not included.
6. The initial and final temperature of water is selected so
that the maximum difference between the ambient and
final water temperature is 5K.
7. The microwave power output P in watts is calculated
from the following formula:
P = 4187 X ∆ T/t
• ∆ T is difference between initial and ending temperature.
• t is the heating time.
The power measured be B (Refer to SPECIFICATIONS) W ± 10.0 %.
CAUTION
1. Water load should be measured exactly to 1 liter.
2. Input power voltage should be exactly specified voltage (Refer to SPECIFICATIONS).
3. Ambient temperature should be 20 ± 2°C (68 ± 3.6°F)
✻ Power level table
Power level
percentage
Output
Power level
percentage
Output
High
100% (P-Hi)
800W
Medium
50% (P-50)
390W
Sauté
90% (P-90)
720W
Medium low
40% (P-40)
300W
Reheat
80% (P-80)
630W
Low
30% (P-30)
220W
Medium high
70% (P-70)
550W
Defrost
20% (P-10)
140W
Simmer
60% (P-60)
470W
Warm
10% (P-10)
90W
26
9-2. MICROWAVE RADIATION TEST
WARNING
1. Make sure to check the microwave leakage before and after repair of adjustment.
2. Always start measuring of an unknown field to assure safety for operating personnel from microwave energy.
3. Do not place your hands into any suspected microwave radiation field unless the safe density level is known.
4. Care should be taken not to place the eyes in direct line with the source of microwave energy.
5. Slowly approach the unit under test until the radiometer reads an appreciable microwave leakage from the
unit under the test.
PROCEDURE
1. Prepare Microwave Energy Survey Meter, 600cc glass beaker,
and glass thermometer 100°C (212°F).
M/W
Def.
Grill
Temp
g
Auto Cook
1. Roast Beef
3. Roast Chicken
5. Vegetable
2. Pour 275cc ± 15cc of tap water initially at 20 ± 5°C (68 ± 9°F) in
the 600 cc glass beaker with an inside diameter of approx. 95
mm(3.5 in.).
2. Roast Pork
4. Fish Fillets
M/W
Defrost
Grill
1000g
Combi
100g
10m.
1m.
Temp
10s.
Clock
Auto Cook
Start/
Speedy cook
Stop/
Clear
Combi
KOC-621Q
3. Place it at the center of the tray and set it in a cavity.
4. Close the door and operate the oven.
5. Measure the leakage by using Microwave Energy Survey Meter
with dual ranges, set to 2450MHz.
1) Measured radiation leakage must not exceed the value
prescribed below. Leakage for a fully assembled oven with
door normally closed must be less than 4mW/Cm2.
2) When measuring the leakage, always use the 5 cm (2 in.)
space cone with probe. Hold the probe perpendicular to the
cabinet and door. Place the space cone of the probe on the
door, cabinet, door seem, door viewing screen, the exhaust air vents and the suction air vents.
3) Measuring should be in a counter-clockwise direction at a rate of 1 in./sec. If the leakage of the cabinet door
seem is unknown, move the probe more slowly.
4) When measuring near a corner of the door, keep the probe perpendicular to the areas making sure the probe
end at the base of the cone does not get closer than 2 in. from any metal. If it does not, erroneous reading may
result.
27
9-3. COMPONENT TEST PROCEDURE
• High voltage is present at the high voltage terminal of the high voltage transformer during any cooking cycle.
• It is neither necessary nor advisable to attempt measurement of the high voltage.
• Before touching any oven components or wiring, always unplug the oven from its power source and discharge the
capacitor.
1. High voltage transformer
1) Remove connections from the transformer terminals and check continuity.
2) Normal readings should be as follows :
Secondary winding ... Approx. 100 Ω±10%
Filament winding ... Approx. 0 Ω
Primary winding ... Approx. 1.2 Ω
2. High voltage capacitor
1) Check continuity of capacitor with meter on the highest OHM scale.
2) A normal capacitor will show continuity for a short time, and then indicate 10MΩ once the capacitor charged.
3) A shorted capacitor will show continuous continuity.
4) An open capacitor will show constant 10MΩ.
5) Resistance between each terminal and chassis should be infinite.
3. High voltage diode
1) Isolate the diode from the circuit by disconnecting the leads.
2) With the ohmmeter set on the highest resistance scale measure the resistance across the diode terminals.
Reverse the meter leads and again observe the resistance reading. Meter with 6V, 9V or higher voltage batteries
should be used to check the front-back resistance of the diode, otherwise an infinite resistance may be read in
both directions. A normal diode's resistance will be infinite in one direction and several hundred k Ω in the other
direction.
4. Magnetron
For complete magnetron diagnosis, refer to "Measurement of the Microwave Power Output." Continuity checks can
only indicate and open filament or a shorted magnetron. To diagnose for an open filament or a shorted magnetron,
1) Isolate magnetron from the circuit by disconnecting the leads.
2) A continuity check across magnetron filament terminals should indicate 0.1 Ω or less.
3) A continuity check between each filament terminal and magnetron case should read open.
5. Fuse
If the fuse in the primary and monitor switch circuit is blown when the door is opened, check the primary and
monitor switch before replacing the blown fuse. In case the fuse is blown by an improper switch operation, replace
the defective switch and fuse at the same time. Replace just the fuse if the switches operate normally.
28
9-4. COMPONENT ACTION
COOKING MODE
MANUAL
M/W
MODE
GRILL
COMBI
MAGNETRON
UPPER ELEMENT LOWER ELEMENT
●
●
●
●
●
TEMP
DEFROST
●
AUTO
ROAST BEEF
●
●
COOK
ROAST PORK
●
●
ROAST CHICKEN
●
●
FISH FILLETS
●
VEGETABLE
●
29
●
10. WIRING DIAGRAM
30
11. EXPLODED VIEW AND PARTS LIST
1. DOOR ASSEMBLY
Refer to 6. Disassembly and assembly.
2. CONTROL PANEL ASSEMBLY
Refer to 6. Disassembly and assembly.
3. TOTAL ASSEMBLY
31
NO
PART NAME
A00
DOOR AS
B00
CONTROL-PANEL AS
F01
F02
F03
F04
F05
F06
F07
F08
F09
F10
F11
F12
F13
F14
F15
F16
F17
F18
F19
F20
F21
F22
F23
F24
F25
F26
F27
F28
F29
F30
F31
F32
F33
F34
F35
F36
F37
F38
F39
F40
F41
F42
F43
F44
F45
F46
F47
F48
F49
F50
F51
F52
F53
F54
F55
F56
F57
F58
F59
F60
F61
F62
F63
CABINET AS
SCREW TAPPING
SENSOR TEMPERATURE
SCREW TAPPING
SCREW TAPPING
SCREW TAPPING
SCREW TAPPING
SCREW TAPPING
CORD POWER AS
NOISE-FILTER
SCREW TAPPING
SCREW TAPPING
MOTOR SHADED POLE
GUIDE WIND
FAN
NUT HEX
SCREW TAPPING
MAGNETRON
SPECIAL SCREW
SCREW TAPPING
HEATER *U
SUPPORTER HEATER *U
SCREW TAPPING
COVER HEATER *U
SCREW TAPTITE
HOLDER HV CAPACITOR
CAPACITOR HV
DIODE HV
FUSE HV
TRANS HV
SPECIAL SCREW
BASE
FOOT
SCREW TAPPING
SCREW TAPTITE
STOPPER HINGE *U AS
HARNESS MAIN
SW MICRO
SW MICRO
SW MICRO
LEVER LOCK
LOCK
LAMP
MOTOR SYNCRO
SCREW TAPPING
SCREW TAPTITE
COVER WAVE GUIDE
COUPLER
GUIDE TRAY
TRAY METAL
TRAY RACK AS
SCREW TAPPING
THERMOSTAT
SCREW TAPPING
COVER INSULATOR *T
SCREW TAPPING
CLAMP WIRE
HEATER
SCREW TAPTITE
GUIDE AIR OUTLET
NUT HEX
CAVITY JOINT AS
REAR-PLATE *O
DESCRIPTION
KOG-621Q0S
KOG-624Q0S
KOC-621Q0S
KOG-624Q0S
KOC-621Q0S
T1 TRS 4*10 MFZN
PTM-K312-D7
T1 TRS 4*10 MFZN
T2S TRS 4*12 MFZN
T1 TRS 4*10 MFZN
T2S TRS 4*12 MFZN
T1 TRS 4*10 MFZN
3X1.5 80X80 120-RTML 1.4M
DWLF-M02
T1 TRS 4*10 MFZN
T2S PAN 4X30 MFZN
230V 25W MW15CA-K01
PP 5113MF6 A353B
P.P GF20
6N-2-5 MFZN
T2S TRS 4*12 MFZN
2M218H(F)
T2 FLANGE 4X13 PW SE M
T1 BIN 4*8 MFNI
230V 400W R18374001
STS430 T0.5
T2S TRS 4*8 MFZN
STS430-2B/HL T0.6
TT3 TRS 4X8 MFZN
SECC T0.6
2100VAC 0.98UF #187
"HVR-1X-3AB 12KV #187"
5KV 0.7A HV-41A70-1 #187
DW-R80S0-62T
TT3 HEX 4X8 FLG MFZN
SBHG T0.8
DASF-310
T1 TRS 4*10 MFZN
TT3 TRS 4X8 MFZN
KOR-121M0A
KOC-621Q0S
VP-533A-OF SPNO #187 200G
VP-531A-OF/SZM-V16-FA-61
VP-533A-OF SPNO #187 200G
POM
POM
BL 240V 25W T25 C7A H187
100/240V 4W GM-16-24FD16
T2S PAN 4X10 MFZN
TT3 TRS 4X8 MFZN
MICA T0.35
PTFE
SPP T1.0
SPP T0.6
KOC-621Q0S
T2S PAN 3X6 MFZN
OFF:145 ON:135 V #187
T1 TRS 4*10 MFZN
SECC T0.5
T1 TRS 4*10 MFZN
SBHG
230V 1150W 1B08965001
TT3 TRS 4X8 MFZN
SA1D-80 T0.5
6N-2-5 MFZN
KOC-621Q0S
SBHG T0.6
32
PART CORD
3511709210
3511709230
PKCPSWEQ20
PKCPSWEQ30
3510806710
7112401011
3514801400
7112401011
7122401211
7112401011
7122401211
7112401011
35113A5QJ5
3518603710
7112401011
7121403011
3963512910
3512513700
3511800100
7392500011
7122401211
3518002200
3516002700
7113400814
3512802000
3515304000
7122400811
3511404410
7272400811
3513003200
3518302200
3518400400
3518700230
3518118710
3516003700
3510310800
3512101400
7112401011
7272400811
3515202800
3512718900
4415A17352
4415A66910
4415A17352
3513701300
3513807900
3513601600
3966030500
7121401011
7272400811
3511404710
3517401900
3512512810
3517205500
3517208400
7121300611
3518903200
7112401011
3511404500
7112401011
3511200400
3512803300
7272400811
3512513110
7392500011
3516107530
3516503700
Q'TY
1
1
1
1
1
3
1
1
1
4
2
1
1
1
1
2
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
4
1
4
5
2
1
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
12. PRINTED CIRCUIT BOARD
CIRCUIT CHECK PROCEDURE
1. Low voltage transformer check
The low voltage transformer is located on the P.C.B.
Measuring condition: Input voltage: 230V / Frequency: 50Hz
3 4
5
6
Terminal
Voltage(olad)
Voltage(no load)
6-10
DC 13V
DC 14V
10
LVT1
DMR-621FS
AS 230V/50Hz
NOTE
1. Secondary side voltage of the low voltage transformer changes in proportion to fluctuation of power source
voltage.
2. The allowable tolerance of the secondary voltage is within ± 5% of nominal voltage.
2. Voltage Check
- Key check point
NO
CHECK POINT
1
IC1 PIN 55, 64
2
IC1 PIN 17
REMARK
5VDC±5%
5V
0V
T
3
T : 20 ms(50Hz)
IC1 PIN 30 OR 31
5V
0V
T
T : 250 ns(4MHz)
- Check method
NO
MEASURE POINT
WAVE FORM
REMEDY
REMARK
1
A
DC 5V±5%
Replace C13, C3
NO LOAD
2
B
DC 17V±20%
Replace D10~D13, EC4
NO LOAD
NOTE: Each measure point must be measured with GND points.
33
3. Case of no microwave oscillation
1) When touching M/W button, oven lamp turns on and Fan motor and turntable rotate, and cook indicator in
display comes on.
*Cause: RELAY 1 does not operate.
B
A
8
D2
M/W
1N4148
RY1
G5G-1A-DT 12V
Q10 C106M
STATE
POINT A
POINT B
RELAY 1 ON
+5V DC
GND
RELAY 1 OFF
GND
+13V DC
2) When touching M/W button, oven lamp does not turn on and turntable motor does not rotate but cook indicator
in display comes on.
*Cause: RELAY 5 does not operate.
B
LAMP,
TRAY
A
16
D15
1N4148
RY5
Q7 C106M
CS11-12SH 12V
STATE
POINT A
POINT B
RELAY 5 ON
+5V DC
GND
RELAY 5 OFF
GND
+13V DC
3) When touching M/W button, oven lamp turn on and turns on and fan motor does not rotate but cook indicator in
display comes on.
*Cause: RELAY 6 does not operate.
B
FAN
A
18
D16
1N4148
RY6
Q12 C106M
CS11-12SH 12V
STATE
POINT A
POINT B
RELAY 6 ON
+5V DC
GND
RELAY 6 OFF
GND
+13V DC
34
4. Case of no heating of upper grill
When touching GRILL or COMBI button, oven lamp turns on and Fan motor and turntable rotate, and cook
indicator in display comes on.
*Cause: RELAY 3 does not operate.
B
A
14
D4
UPPER
GRILL
1N4148
RY3
Q11 C106M
G5G-1A-DT 12V
STATE
POINT A
POINT B
RELAY 3 ON
+5V DC
GND
RELAY 3 OFF
GND
+13V DC
5. Case of no heating of lower grill
When touching TEMP button, oven lamp turns on and Fan motor and turntable rotate and cook indicator in display
comes on.
*Cause: RELAY 4 does not operate.
B
A
15
D14
LOWER
GRILL
1N4148
RY4
Q6 C106M
CS11-12SH- 12V
STATE
POINT A
POINT B
RELAY 4 ON
+5V DC
GND
RELAY 4 OFF
GND
+13V DC
35
6. Case of no stopping of the count down timer
When the door is opened during operation, the count down timer does not stop.
CN1
A
B
35313-0210
1
2
R1 1K
7
D.O.M SW
D1
R4
C1
1N4148
10K
104Z
+5V
POINT
A
B
DOOR OPEN
OPEN
+5V DC
DOOR CLOSED
CLOSE
GND
STATE
CHECK NO
1
METHOD
Check the stage(ON,OFF) of the door open
monitor switch by resistance measurement.
36
REMEDY
Replace door open monitor swith.
13. P.C.B. CIRCUIT DIAGRAM
37
PCB ASS’Y PART LIST
NO
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
NAME
BUZZER
CAPACITOR CERAMIC
CAPACITOR CERAMIC
C ARRAY
CAPACITOR ELECTRO
CAPACITOR ELECTRO
CAPACITOR ELECTRO
CONNECTOR WAFER
CONNECTOR WAFER
CONNECTOR WAFER
CONNECTOR WAFER
DIODE SWITCHING
DIODE SWITCHING
DIODE RECTIFYING
DIODE ZENER
LED DISPLAY
IC MICOM
REGULATOR
PCB MAIN
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR
RESISTOR ARRAY
RESONATOR CERAMIC
SW RELAY
SW RELAY
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANS POWER
WIRE COPPER 5mm
42
43
44
WIRE COPPER 10mm
WIRE COPPER12.5mm
RESISTOR
SYMBOL
BZ1
C1,C3,C8,C9,C13
C11,C12
CA1
EC2
EC3
EC4
CN1
CN2
CN4
CN5
D2,D4,D14~D16
D1,D7,D8,D9
D5,D6,D10~D13
ZD2
DP1
IC1
VL1
M235
R4,R30,R36,R37
R1,R32,R34
R40
R38,R39
R5,R9,R17,R18
R31
R33
R10~R16
R41~R43
R6
R7
R8
RA1
CR1
RY1,RY3
RY4~RY6
Q8
Q15
Q1~Q5
Q6,Q7,Q10~Q13
LVT1
J1,J2,J6,J8,J9
J11~J13,J15.J19
J7,J14,J16~J18
J3,J4
SJ2
38
SPECIFCATION
BM-20K
104 50V Z AXIAL
473 50V Z AXIAL
1000pF, 2.54MM
10V RSS 470uF
25V RSS 470uF
25V RSS 1000uF
35313-0210
35312-0310
FCZ254-8
35328-0610
1N4148 AUTO 52mm
1N4148M 5MM
1N4004A AUTO 52mm
UZ -3.9BSB
DDRG-621S-1
TMP87CK40ANMC7805C
81.5 X 214
1/6W 10K Ohm 5%
1/6W 1K Ohm 5%
1/6W 2K Ohm 5%
1/6W 4.7K Ohm 5%
1/6W 100K Ohm 5%
1/6W 1M Ohm 5%
1/6W 200 Ohm 5%
1/6W 330 Ohm 5%
1/2W 27 Ohm 5%
1/6W 5.88K Ohm 1%
1/6W 16.9K Ohm 1%
1/6W 1.30K Ohm 1%
5P(4) 1/8 100K 5%
CRT-4.00MS
G5G-1A-DT 12V
CS11-12SH
KTA1266Y AUTO
KTC3198GR AUTO
KRA106M AUTO
KRC106M AUTO
DMR-621FS
1/0.52 TIN COATING
PART CODE
3515600100
CCZF1H104Z
CCZF1H473Z
CN4XB-102M
CEXF1A471V
CEXF1E471V
CEXF1E102V
30166M7020
30166M5030
441M367130
4CW3061MX0
DZN4148--DZN4148M-DZN4004A-DZUZ3R9BSB
DDDRG621S1
13GS621Q00
1CPMC7805C
3514325200
RD-AZ103JRD-AZ102JRD-AZ202JRD-AZ472JRD-AZ104JRD-AZ105JRD-AZ201JRD-AZ331JRD-2Z270JS
RN-AZ5881F
RN-AZ1692F
RN-AZ1301F
RA-85X104J
5P4R00MTS5SC0101123
5SC0101128
TZTA1266YTZTC3198GR
TZRA106M-TZRC106M-5EPV041412
85801052GY
Q'TY
1
5
2
1
1
1
1
1
1
1
1
5
4
6
1
1
1
1
1
4
3
1
2
4
1
1
7
3
1
1
1
1
1
2
3
1
1
5
6
1
10
1/0.52 TIN COATING
1/0.52 TIN COATING
1/6W 1K Ohm 5%
85801052GY
85801052GY
RD-AZ102J-
5
2
1
DAEWOO ELECTRONICS CO., LTD.
686, AHYEON-DONG MAPO-GU SEOUL, KOREA
C.P.O. BOX 8003 SEOUL, KOREA
TELEX: DWELEC K28177-8
CABLE: “DAEWOOELEC”
S/M NO. : C621Q0S002
PRINTED DATE: Feb, 2002
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement