Corsair CD Player / Radio

Corsair CD Player / Radio
Thanks for shopping with Improvements!
Corsair CD Player / Radio
Item #453887
To order, call
1-800-642-2112
West Chester, OH 45069
1213
If you have questions regarding this product, call
1-800-642-2112 Mon.-Fri. 9:00-5:00 EST (Ohio)
and ask for our product specialists, or e-mail:
[email protected]
See many more products on the Internet!
www.ImprovementsCatalog.com
If you have any questions regarding this product,
call 1-800-642-2112 and ask for our product
specialists (Mon.-Fri. 9:00-5:00 EST) or e-mail:
WARNING:
General
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE. DO NOT REMOVE COVER.
PILOT LAMPS SOLDERED IN PLACE. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
CAUTION: TO REDUCE
THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE
COVER (OR BACK). NO
USER - SERVICEABLE
PARTS INSIDE. REFER
SERVICING TO QUALIFIED
SERVICE PERSONNEL.
Connect your stereo headphones (not included) to
the HEADPHONE JACK (10). While headphones
are connected, the internal speakers will be disabled.
The exclamation point
within an equilateral
triangle is intended to
alert user to the
presence of important
operating and
maintenance (servicing)
instruction in the
literature accompanying
the appliance.
For Compact Disc Units Only:
INVISBLE LASER RADIATION WHEN OPEN AND INTERLOCK FAILED
OR DEFEATED. AVOID DIRECT EXPORSURE TO LASER BEAM.
To remove a disc from its storage case, press down
on the center of the case and lift the disc out,
holding it carefully by the edges.
Fingerprints and dust should be carefully wiped off
the disc’s recorded surface with a soft cloth. Unlike
conventional record, compact discs have no grooves
to collect dust and microscopic debris, so gently
wiping with a soft cloth should remove most particles.
Wipe in a straight line from the inside to the
outside of the disc. Small dust particles and light
stains will have absolutely no effect on reproduction
quality.
B EN Z E N E
AM 530 - 1710 KHz
FM 88 - 108 MHz
AC 120V ~ 60Hz
18W
3” 8Ohm 5W x 2
* DESIGN AND SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
1
Make sure the radio is plugged in correctly.
2
Check to see that the power button is
pushed in.
1
Check the volume level by turning the volume
knob.
CD does not play
Specification
:
:
Power Supply
:
Power Consumption :
Speaker
:
There is no Power
There is no Sound
COMPACT DISC CARE
CAUTION
Frequency Range
Troubleshooting
Care and Maintenance
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lighting flash with
arrowhead symbol, within
an equilateral triangle, is
intended to alert user to
the presence of uninsulated
"dangerous voltage" within
the product's enclosure
that may be of sufficient
magnitude to constitute
risk of electric shock
to persons.
Headphone Jack
1
Check to make sure CD is inserted correctly
(label side facing up).
2
Check that the surface of the CD is clean
3
Make sure function switch is set to CD.
CLEANER
Clean the disc periodically with a soft, lint-free, dry
cloth. Never use detergents or abrasive cleaners
to clean the disc. If necessary, use a CD cleaning
kit.
Never write on or affix labels to the surface of compact
discs.
CARE OF THE CANBINET
If the cabinet becomes dusty wipe it with with a soft
dry dust cloth. Do not use any wax, polish sprays,
or abrasive cleaners on the cabinet.
CAUTION
Never allow any water or other liquids to get inside
the unit while cleaning.
11
Clock & Alarm Operation
Battery Back-Up
This Model includes a battery back-up circuit. The
battery will maintain the clock and alarm settings in
the event of a power failure. The battery back-up
requires one 9V battery (not included). The battery
compartment is located on the back of the radio. To
install/replace the battery, follow the instructions below.
1
Press in on the locking tab to remove the BATTERY
COVER (25).
Welcome
Thank you for purchasing the Crosley Corsair
(CR612). Before operating this unit, please read this
manual thoroughly and retain it for future reference.
About This Manual
Instructions in this manual describe the control
functions of the CR612.
Table of Contents
Getting Started
Control Locators....................... 4 - 5
Unpacking ................................ 6
Set up ....................................... 6
Radio
AM/FM Tuning ........................ 6
CD Player
Player a CD ............................ 7
Programmed Play .................. 7
Battery Compartment
(For Clock Backup)
Clock & Alarm Operation
2
Attach a 9V battery to the battery contacts as
shown.
Setting the Clock .....................
Setting the Alarm .....................
Snooze .....................................
Sleep function .........................
Battery Back-Up ......................
8
8
9
9
10
General
3
Tuck the battery back into the battery compartment
and replace the battery cover.
If the power is interrupted, the clock and alarm times
will remain stored but the display will be blank to
conserve power. The display will come back on and
show the correct time once power has been restored.
Note: In the event of a power failure, the alarm will
default to buzzer mode until power is restored.
The life of the battery will depend on how often you
lose power and the length of power outages. It is
recommended to replace the battery every 9-12
months.
10
Headphone Jack ..................... 11
Care and Maintenance ............ 11
Troubleshooting Guide ............. 11
Warranty ................................... 12
Control Locators
Clock & Alarm Operation
Unit Controls
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
4
Tuner Dial
LED Display
FM Stereo Indicator
Speakers
Power Button
Tuning Knob
AM/FM Switch
Function Switch
Volume Knob
Headphone Jack
Sleep
Alarm 1
Alarm 2
Time
Program
Forward Skip
Backward Skip
CD Mode
CD Display
Stop
Play/Pause
1
4
10
2
8
7
9
11
Snooze Function
3
5
6
12
13
14
4
Sleep Function
Using the snooze function will temporarily turn the
alarm off for a period of 6 minutes. After 6 minutes,
the alarm will reactivate. To use the snooze function,
follow the instructions below.
The sleep function is designed to allow you to listen
to the Radio or CD and turn itself off automatically.
To use the sleep function, follow the instructions
below.
1
Once alarm is activated, press the Snooze button.
The snooze LED will light and the Alarm 1 or
Alarm 2 LED will continue to flash.
1
With the unit on or off, press the Sleep button.
The display will show 90 for 90 minutes. The
Sleep LED will come on.
2
The alarm will turn off for a period of 6 minutes.
After 6 minutes, the alarm will sound again.
2
3
After 6 minutes, the alarm will sound again.
Press the Sleep button again while 90 is showing
to change the duration of the Sleep time. You
can choose between 90, 60, 30, and 15 minutes
in sleep mode.
3
Once a time is selected, the radio goes into
sleep mode and the unit will turn off after the
set period of time.
Note: If the power is turned off and the unit is
in CD mode, pressing Sleep will automatically
start the CD playing. If the power is turned on
and the sleep button is pressed, you will have
to manually start the CD.
21 20 19 18 17 16 15
9
Clock & Alarm Operation
Control Locators
Setting The Clock
Unit Controls
The clock time can be set with the power turned on
or off as long as the unit is plugged in. To set the
clock, follow the instructions below.
To set Alarm 2
1
Press Alarm 2. The clock display will switch to
alarm time and start to flash. The Alarm 2 LED
will come on.
1
Press the TIME (14) button. The clock display
will begin to flash.
2
2
Press the FORWARD SKIP
(16) button to
set the hour.
Note: There is a PM indicator light that will come
on to denote PM hours.
Press the FORWARD SKIP
(16) button to
set the hour.
Note : There is a PM indicator light that will come
on to denote PM hours.
3
3
Press the BACKWARD SKIP
set the minutes.
Press the BACKWARD SKIP
set the minutes.
4
4
Once the correct time is set, press the TIME (14)
button again to store the time.
Once you have the correct alarm time set for
Alarm 2, press the Alarm 2 button again to turn
the alarm on. The Alarm 2 LED with stay lit.
5
5
To switch between 12H and 24H mode, press
and hold the TIME (14) button.
To turn the alarm off, press the Alarm 2 button
again. The alarm will turn off and the LED light
will go off.
6
Once set, the alarm will sound once the clock
reaches the set alarm time for Alarm 2. The
Alarm 2 LED will begin to flash.
7
To turn the alarm off while it is going off, press
the Alarm 2 button.
(17) button to
Setting The Alarm
This unit features dual alarms. You can set each
alarm to wake you at different times. The alarms can
be set with the power turned on or off as long as the
unit is plugged in. To set the alarm(s), follow the
instructions below.
To set Alarm 1
1
Press Alarm 1. The clock display will switch to
alarm time and start to flash. The Alarm 1 LED
will come on.
2
Press the FORWARD SKIP
(16) button to
set the hour.
Note : There is a PM indicator light that will come
on to denote PM hours.
3
Press the BACKWARD SKIP
set the minutes.
4
Once you have the correct alarm time set for
Alarm 1, press the Alarm 1 button again to turn
the alarm on. The Alarm 1 LED with stay lit.
5
To turn the alarm off, press the Alarm 1 button
again. The alarm will turn off and the LED light
will go off.
6
Once set, the alarm will sound once the clock
reaches the set alarm time for Alarm 1. The Alarm
1 LED will begin to Flash.
7
To turn the alarm off while it is going off, press
the Alarm 1 button.
8
(17) button to
22
23
24
25
26
Snooze
CD Door Open
FM Wire Antenna
Battery Cover
AC Power Cord
(17) button to
23
22
Note : The alarm will wake you to Radio, CD or
Buzzer. Turn the FUNCTION SWITCH to your
desired wake up mode. You can set this mode
with the radio on or off. In the case of power
outage, the alarm will wake you to Buzzer if the
battery is installed. The alarm will sound for 60
minutes if not stopped manually by pressing
Snooze or by turning the alarm off.
24
26
25
5
Getting Started
RADIO Operation
CD Player
AM/FM Tuning
Unpacking
1
Pull the packing materials off the unit.
2
Remove the plastic bag covering the radio.
3
Press OPEN (23) to open the CD DOOR.
4
Remove the cardboard shipping card from the
CD Player.
5
Unwind FM Antenna (24) and allow it to hang
straight down.
6
Remove plastic bag covering the AC Power Cord
(26).
Note: Save all packing materials.
1
2
Turn the FUNCTION SWITCH (8) to the Radio
position.
3
Turn the AM/FM SWITCH (7) to the desired
tuning band.
4
Rotate the TUNING KNOB (6) to tune in the
desired station. When tuning in FM stations,
the FM STEREO INDICATOR (3) will appear
the brightest when the station has reached its
strongest frequency.
5
Set Up
Press the POWER BUTTON (5) to turn the unit
on.
Rotate the VOLUME KNOB (9) to set the
desired volume level.
Playing a CD
1
Press the POWER BUTTON (5) to turn the unit
on.
2
Turn the FUNCTION SWITCH (8) to the CD
position.
3
Press the CD DOOR OPEN BUTTON (23) to
open the CD DOOR.
4
3
In Normal mode, the CD will play from track 1 or
the first selected track till the end of the CD and
stop.
4
When in Repeat 1, the repeat light will flash and
only the selected song will be repeated. You can
select the song to repeat before you press play
or during playback.
Load the desired CD into the player with the
labeled side of the CD facing up and close the
CD DOOR.
5
5
When in Repeat all, the repeat light will stay on
continuously. In this mode, once the CD is
finished, it will start over from the beginning.
The LED DISPLAY (2) will flash ( - - ) for a second
and then display the total number of tracks on
the CD.
Note: The display will read “no” if there is no
disc in the unit or the disc cannot be read.
6
When in Random mode, the random light will
stay on continuously. When Random mode, the
CD player will randomly play tracks in no particular
order.
6
Press the PLAY/PAUSE BUTTON
begin playing the CD.
7
7
Pushing STOP (20) will clear the Random and
Repeat functions and the unit will return to Normal
Mode.
To skip to a different track, press the FORWARD
(16) or BACKWARD SKIP
(17)
SKIP
button until you reach the desired track number.
Pressing the FORWARD SKIP
(16) button
will advance forward from track to track. Pressing
(17) will skip
the BACKWARD SKIP
backwards from track to track.
Hints For Better Reception
1
Untie the AC Power Cord (26) at the back of the
unit.
2
Remove Plug safety cover on the prongs of the
plug.
3
Plug the AC cord into an appropriate outlet.
FM – Make sure the FM WIRE ANTENNA (24) is
fully extended in a straight line.
AM – This radio is equipped with an internal AM
antenna. Try rotating the unit slightly to one
side or the other to improve AM reception.
8
9
AC
Polarized Plug
4
5
6
This product is equipped with a polarized
alternating current line plug (a plug having one
blade wider than the other). This plug will fit into
the power outlet only one way. This is a safety
feature. If you are unable to insert the plug fully
into the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the
purpose of the polarized plug.
Install 9V battery in the Battery Compartment (25)
if you wish to use the battery backup. See page
10 for instructions on installing the battery.
(21) to
To fast forward through part of a particular track,
press and hold the FORWARD SKIP
(16)
button. Playback will resume at the point that
you release the button. To reverse playback,
(17)
press and hold the BACKWARD SKIP
button.
To pause during playback, press the
PLAY/PAUSE BUTTON
(21). To resume play,
press the button again.
10 To Stop playback, press the STOP BUTTON
(20).
Programmed Play
You can program up to 20 tracks that will play in the
order that you program them.
1
In CD Mode with a CD inserted and play stopped,
press the PROGRAM BUTTON (15)
2
Select a track you would like to program in
memory by using the Forward or Backward skip
buttons.
3
Once you have selected a track, press the
PROGRAM BUTTON (15) again. That track is
now stored.
4
5
Repeat steps 2-3 to store up to 20 tracks.
6
To clear programming, press the stop button.
Programmed tracks will also be cleared if the
CD Door is opened or the power is disconnected.
Play Mode
1
There are four modes in which you can listen to
your CD :
Normal, Repeat 1, Repeat all, and Random.
2
To change between these options, press the CD
MODE (18) button. The play mode will change
in the following sequence.
Repeat
Repeat all
Random
When all desired tracks are programmed, press
the PLAY/PAUSE BUTTON (21) to begin playback
of the selected tracks. The tracks will play in the
order in which they were programmed.
Normal
7
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement