SPLIT TYPE ROOM AIR CONDITIONER -

SPLIT TYPE ROOM AIR CONDITIONER -
Before using your air conditioner, please read
this manual carefully and keep it for future reference.
SPLIT- TYPE
ROOM AIR CONDITIONER
R ead T hi s M a n u a l
Inside you will find many helpful hints on how
to use and maintain your air conditioner properly.
Just a little preventative care on your part can
save you a great deal of time and money over
the life of your air conditioner. You'll find many
answers to common problems in the chart of
troubleshooting tips. If you review the chart of
Troubleshooting Tips first, you may not need
to call for service.
CONTENTS
SOCIABLE REMARK
Sociable remark..................................................................................
SAFETY PRECAUTIONS
Warning .........................................................................................
Caution .........................................................................................
OPERATING INSTRUCTIONS
Parts names ........... ........................................................................
Operating
temperature.......................................................................
Manual operation .............................................................................
Airflow direction control ....................................................................
How
the
air
conditioner
works
..........................................................
CARE AND MAINTENANCE
Care and maintenance ...........................................................................
OPERATION TIPS
Operation tips ............ ....................................................................
TROUBLESHOOTING TIPS
Troubleshooting tips ............................................................................
! CAUTION
Contact an authorised service technician for repair or maintenance of this unit.
Contact the installer for installation of this unit.
The air conditioner is not intended for use by young children or invalids
without supervision.
Young children should be supervised to ensure that they do not play with the
air conditioner.
If the power cord is to be replaced, replacement work shall be performed by
authorised personnel only.
Installation work must be performed in accordance with the national wiring
standards by authorised personnel only.
1
SOCIABLE REMARK
When using this air conditioner in the European countries, the following
instructions must be followed:
DISPOSAL: Do not dispose this product as unsorted municipal waste. Collection
of such waste separately for special treatment is necessary.
It is prohibited to dispose of this appliance in domestic household waste.
For disposal, there are several possibilities:
A) The municipality has established collection systems, where electronic waste can
be disposed of at least free of charge to the user.
B) When buying a new product, the retailer will take back the old product at least
free of charge.
C) The manufacture will take back the old appliance for disposal at least free of
charge to the user.
D)
As old products contain valuable resources, they can be sold to scrap metal
dealers.
Wild disposal of waste in forests and landscapes endangers your health when
hazardous substances leak into the ground-water and find their way into the food
chain.
2
SAFETY PRECAUTIONS
To prevent injury to the user or other people and property damage, the following instructions must be
followed. Incorrect operation due to ignoring of instructions may cause harm or damage. The
seriousness is classified by the following indications.
WARNING
This symbol indicates the possibility of death or serious injury.
CAUTION
This symbol indicates the possibility of injury or damage to property.
Meanings of symbols used in this manual are as shown below.
Never do this.
Always do this.
WARNING
!
Connect with the power
properly.
Do not operate or stop the
unit by switching on or off
the power.
Do not damage or use an
unspecified power cord.
It may cause electric shock or fire.
Otherwise, it may cause electricIt may cause electric shock or fire
shock or fire due to excess heatdue to heat generation.
generation.
!
!
!
Do not modify power cord
length or share the outlet
with other appliances
Do not operate with wet
hands or in damp
environment.
It may cause electric shock or
fire due to heat generation.
It may cause electric shock.
Always ensure effective
earthing.
Do not allow water to run
into electric parts.
No earthing may cause electric
shock.
It may cause failure of machine No installation may cause fire
and electric shock.
or electric shock.
Disconnect the power if
strange sounds, smell, or
smoke comes from it.
Do not drink water drained
from air conditioner.
It may cause fire and electric
shock.
It contains contaminants and
could make you sick.
Use the correctly rated
breaker or fuse.
Do not use the power cord
close to heating appliances.
There is risk of fire or electricIt may cause fire and electric
shock.
shock.
!
Do not direct airflow at
room occupants only.
This could damage your health.
!
Always install circuit
breaker and a dedicated
power circuit.
Do not open the unit
during operation.
It may cause electric shock.
Do not use the power cord near
flammable gas or combustibles, such
as gasoline, benzene, thinner, etc.
It may cause an explosion or fire.
Ventilate room before operating air
conditioner if there is a gas leakage from
another appliance.
Do not disassemble or modify unit.
It may cause explosion, fire and, burns.
It may cause failure and electric shock.
3
SAFETY PRECAUTIONS
CAUTION
When the air filter is to be
removed, do not touch the
metal parts of the unit.
It may cause an injury.
!
Stop operation and close
the window in storm or
hurricane.
Appearance may be
deteriorated due to change
of product color or
scratching of its surface.
Do not place heavy object on the
power cord and take care so that
the cord is not compressed.
Ventilate the room well
when used together
with a stove, etc.
An oxygen shortage
may occur.
Do not put a pet or house
plant where it will be
exposed to direct air flow.
Do not use for
special purposes.
This could injure the pet or
plant.
! Do not place obstacles
around air-inlets or inside
of air-outlet.
Operation with windows
opened may cause wetting
of indoor and soaking of
household furniture.
Do not use strong detergent
such as wax or thinner. Use
a soft cloth for cleaning.
!
Water may enter the unit and
degrade the insulation. It may
cause an electric shock.
When the unit is to be
cleaned, switch off, and turn
off the circuit breaker.
Do not clean unit when
power is on as it may cause
fire and electric shock, it may
cause an injury.
!
Do not clean the air
conditioner with water.
Do not use this air conditioner to preserve precision devices, food, pets,
plants, and art objects.
It may cause deterioration
of quality, etc.
!
It may cause failure of
product or fire.
It may cause failure of
appliance or accident.
!
Ensure that the installation bracket of
the outdoor appliance is not damaged
due to prolonged exposure.
Turn off the main power
switch when not using
the unit for a long time.
!
Always insert the filters
securely. Clean filter
once every two weeks.
If bracket is damaged, there
is concern of damage due to
falling of unit.
Operation without filters
may cause failure.
!
! If water enters the
unit, turn the unit off
and disconnect the
power , contact a
qualified service
technician.
Use caution when unpacking
and installing. Sharp edges
could cause injury.
There is danger of fire or
electric shock.
!
4
OPERATING INSTRUCTIONS
Parts names
Indoor unit
Indoor unit 3
1
2
4
5
1.
2.
3.
4.
5.
6.
7.
8.
7
6
SET
ATO
U
COOL
DRY
HEAT
9
TEMPE
Outdoor unit
RATR
UE
( C。
)
FAN
HIGH
MED
LOW
TEMP
MODE
ON/O
SING
W
SELE
8
DIRECI
AR
TO I
N
RESE
TL
DSPI
FF
FANSP
EED
P
TIME
RO
OKC
Front panel
Air inlet
Air filter(under the panel)
Air outlet
Horizontal air flow grille
Vertical air flow louver(inside)
Display panel
Remote controller
TIME
LED
LAY
ROF
N
F
TURO
B
9.
Connecting pipe, drain hose
10. Air inlet (side and rear)
11. Air outlet
Outdoor unit
10
NOTE:
All the pictures in this manual are for
explanation purpose only. Your air
conditioner may be slightly different.
The actual shape shall prevail.
11
Ind i c a t o r L ights on D ispla y p anel
CLEAN AIR indication lamp(optional):
Lights up when CLEAN AIR feature is activated.
AUTO indication lamp:
Lights up during the Auto operation.
OPERATION indication lamp:
This indicator flashes after power is on and illuminates when the unit is in operation.
DIGITAL DISPLAY indication lamp:
Displays current setting temperature when the air conditioner is in operation.
DEFROST indication lamp:(for cooling and heating model only)
This indicator illuminates when the air conditioner starts defrosting automatically or wh
the warm air control feature is activated in heating operation..
TIMER indication lamp:
Lights up during Timer operation.
5
OPERATING INSTRUCTIONS
N O T E : T his ma n u a l d oes n o t i ncl u d e R emote Co n t r o ller Op e r a t i o ns, se e t he
< < R e m o t e C ontr o l l e r I nstruc t i o n > > p acked wi t h the u n i t for d e tails.
Operating temperature
Temperature
Mode
Heating operation Drying operation
Cooling operation
。
。
17 C~ 32 C
Room temperature
。
。
0 C~ 30 C
10OC~32OC
(<21000Btu/h models)
17OC~32OC
(>21000Btu/h models)
Outdoor temperature
11OC~43OC
。~
。
18 C 43 C
(<21000Btu/h models)
。
。
( -5 C 43 C:For the models with
~
low temperature cooling system)
。
(21 C
。
52 C:For special tropical
~
models
~
。
。
-7 C 24 C
18OC~43OC
(>21000Btu/h models)
。
。
21 C~ 52 C
(For special tropical models)
NOTE:
1. If air condit ioner is used outsi de of the abov e condit ions, cer tain safety protect ion features may
come into operati on and cause the unit to funct ion abnorm ally.
2. Room relat ive humidity less than 80%. If the air condit ioner operates in excess of this figure, the
sur face of the air condit ioner may attract conden sation. Please sets the ver tical air flow louver to its
maximum angle (ver tically to the floor) , and set HIGH fan mode.
3. Optimum per formance will be achi eved within thes e operati ng temperat ure.
Manual operation
Manul operation can be used temporarily in case the remote controller is disable or
maintenance necessary.
1
2
Panel
3
●
Manual control
button
AUTO/COOL
●
●
6
Open and lift the front panel up to an angle
until it remains fixed with a clicking sound.
Push the button until the AUTO indicator
is lit, the unit will work in forced AUTO
mode (the default setting temperature
is 24℃).
Close the panel firmly to its original
position.
CAUTION:
Once you push the manual button, the
operation mode is shifted in an order as:
AUTO, COOL, OFF.
This button is used for testing purposes only.
To restore the remote controller operation,
use the remote controller directly.
OPERATING INSTRUCTIONS
Airflow direction control
Adjust the air flow direction properly otherwise, it
might cause discomfort or cause uneven room
temperatures.
Adjust the horizontal louver using the remote
controller only.
Adjust the vertical louver manually or by remote
controller only(depending on models).
Range
Vertical
louver
(three places)
Range
To set the vertical air flow(Up--Down) direction
Perform this function while the unit is in operation.
Use the remote controller to adjust the air flow
,,
direction. The horizontal louver can be moved at
,,
a range of 6O for each press, or swing up and down
automatically. Please refer to the REMOTE
CONTROLLER OPERATION MANUAL for details.
To set the horizontal air flow direction (left - right)
Move the vertical louver manually to adjust the air flow
in the direction you prefer.
IMPORTANT: Before adjusting the vertical louvers, the
supply power must be disconnected.
For some models, the vertical louver can be adjusted
by using the remote controller. The vertical louver can
,, left
,be
, moved at a range of 6O for each press, or swing
and right automaticallyPlease refer to the
REMOTE CONTROLLER OPERATION MANUAL
for details.
! CAUTION
Do not operate the air conditioner for long periods with the
air flow direction set downward in cooling or dehumidifying
mode.
Otherwise, condensation may occur on the surface of the
horizontal louver causing moisture to drop on to the floor or
on furnishings.
Do not move the horizontal louver manually unless it is
necessary. Always use the remote controller.
When the air conditioner is started immediately after it was
stopped, the horizontal louver might not move for
approximately 10 seconds.
Open angle of the horizontal louver should not be set too
small, as COOLING or HEATING performance may be
impaired due to too restricted air flow area.
Do not operate unit with horizontal louver in closed position.
When the air conditioner is connected to power (initial
power), the horizontal louver may generate a sound for 10
seconds, this is a normal operation.
7
OPERATING INSTRUCTIONS
How the air conditioner works
SLEEP
operation
7 hours timer off
1℃ Set
Temperature
1℃ 1 hour
1 h ou r
C ooli n g
SLEEP
operation
7 hours timer off
Set
Temperature
1℃ 1℃ 1 hour
1 hour
Heat i n g
AUTO operation
When you set the air conditioner in AUTO mode, it will
automatically select cooling, heating(cooling/heating
models only), or fan only operation depending on what
temperature you have selected and the room temperature.
The air conditioner will control room temperature
automatically round the temperature point set by you.
If the AUTO mode is uncomfortable, you can select
desired conditions manually.
SLEEP operation
When you push SLEEP button on remote controller during
cooling, heating(cooling only type without), or AUTO operation ,
the air conditioner will automatically increase (cooling) or
decrease (heating) 1℃ per hour.
The set temperature will be steady 2 hours later. And the air
conditioner will be timer off in 7 hours. The fan speed will be
automatically controlled. This feature can maintain the most
comfortable temperature and save more energy for you.
DRYING operation
The temperature is regulated while dehumidifying by
repeating turning on and off of the cooling operation or
fan only. The fan speed indicator will display AUTO and
low speed will be used.
OPTI M A L o peration
To achieve optimal performance, please note the following:
Adjust the air flow direction correctly so that it is not directed
on people.
Adjust the temperature to achieve the highest comfort level.
Do not adjust the unit to excessive temperature levels.
Close doors and windows on COOL or HEAT modes, or performance may be reduced.
Use TIMER ON button on the remote controller to select a time
you want to start your air conditioner.
Do not put any object near air inlet or air outlet, as the efficienc
of the air conditioner may be reduced and the air conditioner
may stop running.
Clean the air filter periodically, otherwise cooling or heating
performance may be reduced.
Do not operate unit with horizontal louver in closed position.
8
CARE AND MAINTENANCE
Care and maintenance
Cleaning the Grille, Case and Remote Controller
Turn the system off before cleaning. To clean, wipe with
a soft, dry cloth. Do not use bleach or abrasives.
The stick for opening
the panel
NOTE: Supply power must be disconnectd before
cleaning the indoor unit.
CAUTIONS
Filter Handle
A cloth dampened with cold water may be used
on the indoor unit if it is very dirty. Then wipe it
with a dry cloth.
Do not use a chemically treated cloth or duster to
clean the unit.
Do not use benzine, thinner, polishing powder, or
similar solvents for cleaning. These may cause
the plastic surface to crack or deform.
Never use water hotter than 40 C to clean the front
panel, it could cause deformation of discoloration.
Cleaning the air filter
A clogged air filter reduces the cooling efficiency of
this unit. Please clean the filter once every 2 weeks.
1. Lift the indoor unit panel up to an angle,there is a
stick under the front panel .Stick it up and the front
panel remains fixed.
2. Take hold of the handle of the air filter and lift it
up slightly to take it out from the filter holder,
then pull it downwards.
..
3. Remove the AIR FILTER from the indoor unit.
Clean the AIR FILTER once two weeks.
Clean the AIR FILTER with a vacuum cleaner
or water, then dry it up in cool place.
9
CARE AND MAINTENANCE
4. Remove the Air Freshening Filter(Optional filter
included: Plasma Dust Collector/Silver Ion filter /
Bio filter /Vitamin C filter/3M air purifier filter) from
its support frame.(The removing and installation
method are slightly difference, see the pictures
marked
and
on the left.
2
1
Clean
the air
freshening filter at least once a
month, and replace it every 4-5 months.
Clean it with vacuum cleaner, then dry it in cool
place.
.
.
Air freshening filter
1
Air freshening filter
Do not touch the Plasma Dust Collector
Filter within 10 minutes after opening the
front panel,
may cause filter
an electric
shock.
5. Install
the airitfreshening
back into
position.
6. Insert the upper portion of air filter back into the
unit, taking care that the left and right edges line
up correctly and place filter into position.
Maintenance
2
If you plan to idle the unit for a long time, perform the
following:
(1) Operate the fan for about half a day to dry the
inside of the unit.
(2) Stop the air conditioner and disconnect power.
Remove the batteries from the remote controller.
(3) The outdoor unit requires periodic maintenance
and cleaning. Do not attempt to do this yourself.
Contact your dealer or servicer.
Checks before operation
Check that the wiring is not broken off or disconnected.
Check that the air filter is installed.
Check if the air outlet or inlet is blocked after the
air conditioner has not been used for a long time.
Caution
Do not touch the metal parts of the unit when
removing the filter. Injuries can occur when
handling sharp metal edges.
Do not use water to clean inside the air conditioner.
Exposure to water can destroy the insulation,
leading to possible electric shock.
When cleaning the unit, first make sure that the
power and circuit breaker are turned off.
10
OPERATION TIPS
The following events may occur during normal operation.
1. Protection of the air conditioner.
Compressor protection
The compressor can't restart for 3 or 4 minutes after it stops.
Anti-cold air (Cooling and heating models only)
The unit is designed not to blow cold air on HEAT mode, when the indoor heat exchanger is in
one of the following three situations and the set temperature has not been reached.
A) When heating has just starting.
B) Defrosting.
C) Low temperature heating.
The indoor or outdoor fan stop running when defrosting (Cooling and heating models only).
Defrosting (Cooling and heating models only)
Frost may be generated on the outdoor unit during heat cycle when outdoor temperature is low
and humidity is high resulting in lower heating efficiency of the air conditioner.
During this condition air conditioner will stop heating operation and start defrosting automatically.
The time to defrost may vary from 4 to 10 minutes according to the outdoor temperature and
the amount of frost build up on the outdoor unit.
2. A white mist coming out from the indoor unit
A white mist may generate due to a large temperature difference between air inlet and air outlet
on COOL mode in an indoor environment that has a high relative humidity.
A white mist may generate due to moisture generated from defrosting process when the air
conditioner restarts in HEAT mode operation after defrosting.
3. Low noise of the air conditioner
You may hear a low hissing sound when the compressor is running or has just stopped running.
This sound is the sound of the refrigerant flowing or coming to a stop.
You can also hear a low "squeak" sound when the compressor is running or has just stopped
running. This is caused by heat expansion and cold contraction of the plastic parts in the unit
when the temperature is changing.
A noise may be heard due to louver restoring to its original position when power is first turned on.
4. Dust is blown out from the indoor unit.
This is a normal condition when the air conditioner has not been used for a long time or during first
use of the unit.
5. A peculiar smell comes out from the indoor unit.
This is caused by the indoor unit giving off smells permeated from building material, from furniture,
or smoke.
6. The air conditioner turns to FAN only mode from COOL or HEAT (For cooling and
heating models only) mode.
When indoor temperature reaches the temperature setting on air conditioner, the compressor will
stop automatically, and the air conditioner turns to FAN only mode. The compressor will start again
when the indoor temperature rises on COOL mode or falls on HEAT mode (For cooling and heating
models only) to the set point.
11
OPERATION TIPS
7. Dripping water may generate on the surface of the indoor unit when cooling in a high
relatively humidity (relative humidity higher than 80%). Adjust the horizontal louver to
the maximum air outlet position and select HIGH fan speed.
8. Heating mode (For cooling and heating models only)
The air conditioner draws in heat from the outdoor unit and releases it via the indoor unit
during heating operation. When the outdoor temperature falls, heat drawn in by the air
conditioner decreases accordingly. At the same time, heat loading of the air conditioner
increases due to larger difference between indoor and outdoor temperature. If a
comfortable temperature can't be achieved by the air conditioner, we suggest you use a
supplementary heating device.
9. Auto-restart function
Power failure during operation will stop the unit completely.
For the unit without Auto-restart feature, when the power restores, the OPERATION indicator
on the indoor unit starts flashing. To restart the operation, push the ON/OFF button on the
remote controller. For the unit with Auto-restart feature, when the power restores, the unit
restarts automatically with all the previous settings preserved by the memory function.
10. Lightning or a car wireless telephone operating nearby may cause the unit to malfunction.
Disconnect the unit with power and then re-connect the unit with power again. Push the
ON/OFF button on the remote controller to restart operation.
12
TROUBLESHOOTING TIPS
Troubleshooting Tips
Stop the air conditioner immediately if one of the following faults occur. Disconnect the
power and contact the nearest customer service center.
OPERATION indicator or other indicators flash rapidly (5 times every second) and
this flash can't be fixed by disconnecting the power, and then connect it in again.
Trouble
Fuse blows frequently or circuit breaker trips frequently.
Other objects or water penetrate the air conditioner.
The remote controller won't work or works abnormally.
Any one of the malfunction codes appears: E1, E2, E3.............................Ex.
Malfunctions
Unit does not
start
Unit not cooling
or heating
(Cooling/ heating
models only)
room very well
while air flowing
out from the air
conditioner
Cause
What should be done?
Power cut
Wait for power to be restored.
Unit may have become unplugged.
Check that plug is securely in wall
receptacle.
Fuse may have blown.
Replace the fuse.
Battery in Remote controller may
have been exhausted.
Replace the battery.
The time you have set with timer
is incorrect.
Wait or cancel timer setting.
Inappropriate temperature
Set temperature correctly. For
setting.
detailed method please refer to
"Using remote control" section.
Air filter is blocked.
Clean the air filter.
Doors or Windows are open.
Close the doors or windows.
Air inlet or outlet of indoor or
outdoor unit has been blocked.
Clear obstructions away first, then
Compressor 3 or 4 minutes
protection has been activated.
Wait.
restart the unit.
If the trouble has not been corrected, please contact a local dealer or the nearest customer
service center. Be sure to inform them of the detailed malfunctions and unit model.
Notes: Do not attempt to repair the unit yourself.
Always consult an authorised service provider.
13
The d esig n a n d s p e c i f icati o n s a r e s u b j e ct t o c h ange w itho u t p r i o r n o t ice f or p rodu
impr o v e m ent. Consu l t w i t h t h e s a l e s a g e ncy o r m anufac t u r er f o r d e tails.
CS115U-9A5
2 020 001A596 5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising