Display for 5-in-1 Weather Sensor

Display for 5-in-1 Weather Sensor
Instruction Manual
Display for 5-in-1 Weather Sensor
model 06037
Package Contents
1. Display with Tabletop Stand
2. Power Adapter
3. USB Cable
4. Instruction Manual
This product requires an AcuRite 5-in-1 Weather Sensor
(sold separately) to be operational.
IMPORTANT
PRODUCT MUST BE REGISTERED
TO RECEIVE WARRANTY SERVICE
PRODUCT REGISTRATION
Register online to receive 1 yearwarranty protection
www.AcuRite.com
Questions? Contact Customer Support at
(844) 228-5465 or visit www.AcuRite.com.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
Features & Benefits
Display
1 23 4 1
5
33
32
31
30
29
6
7
8
9
10
11
12
13
28
27
26
25
14
15
24
16
17
23
22
21
20
2
19
18
1. Previous 2 Wind Directions
2. Backlight Button
19.
Button
For setup preferences.
20.SET Button
For momentary backlight and
dimmer settings.
For setup preferences.
3. Current Wind Speed
4. Current Wind Direction
5. Current Indoor Temperature
21.
Button
For setup preferences.
22.SELECT Button
Press to change the WEATHER
SELECT category data being
displayed.
Arrow icon indicates direction
temperature is trending.
6. Display Low Battery Indicator
7. Peak Wind Speed
23.Weather TickerTM
24.Heat Index/ Wind Chill Alert
Indicator
Highest speed from the last
60 minutes.
Activates when heat index rises over
90ºF (32ºC) or when wind chill drops
below -17ºF (-27ºC).
8. Current Indoor Humidity
Arrow icon indicates direction
humidity is trending.
25.Learning Mode Icon
9. Wind Speed Alert Indicator
Disappears after weather forecast
self-calibration is complete.
Activates when wind speed is over
50 mph.
26.WEATHER SELECT
10.Clock
11.Heavy Rainfall Warning Icon
Displays heat index, dew point, wind
chill, feels like, days with rain this
month, and days since last recorded
rainfall.
Activated when over 1 inch of rainfall
is recorded in 2 hours or less.
27.Date
28.Current Outdoor Humidity
12.AUTO DIM Indicator
Indicates display is in auto-dimming
brightness mode (see page 6).
Arrow icon indicates direction
humidity is trending.
13.Current Rainfall
Rainfall recorded since 12:00am.
29.Average Wind Speed
14.12 to 24 Hour Weather Forecast
Average wind speed over the past
2 minutes.
Self-Calibrating Forecasting pulls data
from your 5-in-1 sensor to generate
your personal forecast.
30.5-in-1 Sensor Signal Strength
31.Sensor Low Battery Indicator
32.Current Outdoor Temperature
Arrow icon indicates direction
15.Storm Alert Indicator
Activates when barometric pressure
drops.
temperature is trending.
16.Month/Year/All-Time Rainfall
17.Current Barometric Pressure
33.Calibration Indicator
Appears next to calibrated values.
Arrow icon indicates direction
pressure is trending.
18.RAINFALL Button
Press to change the RAINFALL
data being displayed (Month, Year,
All-Time).
3
Back of Display
1 2
4
3
DEVICE ID
############
6
7
5
9
8
BACK OF DISPLAY
7. CLEAR RECORD/ RESET BUTTON
Press and release to clear data recorded since 12:00 am. Press and HOLD for full reset to factory defaults.
1. Plug-in for Power Adapter
2. Plug-in for USB Cable
3. Integrated Hang Hole
For easy wall mounting.
8. Power Adapter
9. USB Cable for PC Connection
4. DEVICE ID
12 digit unique ID required for online connectivity functions.
10. Battery Compartment Cover
(not shown)
5. Backup Battery Compartment
6.
A-B-C Switch
ID code that must match 5-in-1 sensor’s A-B-C switch to ensure units synchronize.
4
SETUP
Display Setup
3 Write Down the DEVICE ID
1 Set the A-B-C Switch
The A-B-C switch is located inside
the battery compartment. It can
be set to A, B or C. However,
you must select the same letter
choices for both the sensor and
the display in order for the units
to synchronize.
12 digit unique ID needed for
online connectivity functions.
24 C8 6E
4 Install or Replace Backup
Batteries (optional)
Insert 3 x AA alkaline batteries
into the battery compartment,
as shown. Follow the polarity
(+/-) diagram in the battery
compartment.
2 Plug Power Adapter into
Electric Outlet
3
1
A-B-C Switch
set to match
sensor
Write Down
DEVICE ID
12 digit number
4
Install Backup
Batteries
3 AA Batteries
ABC
2
Plug in Power
Adapter
IMPORTANT: Batteries are a backup
power source to preserve records
in the event of a power outage.
Power adapter is the recommended
primary power source to enjoy the full
functionality of this product.
PLEASE DISPOSE OF OLD OR DEFECTIVE BATTERIES IN AN ENVIRONMENTALLY SAFE
WAY AND IN ACCORDANCE WITH YOUR LOCAL LAWS AND REGULATIONS.
BATTERY SAFETY: Clean the battery contacts and also those of the device prior to battery installation. Remove batteries from equipment which is not to
be used for an extended period of time. Follow the polarity (+/-) diagram in the battery compartment. Promptly remove dead batteries from the device. Dispose of
used batteries properly. Only batteries of the same or equivalent type as recommended are to be used. DO NOT incinerate used batteries. DO NOT dispose of batteries
in fire, as batteries may explode or leak. DO NOT mix old and new batteries or types of batteries (alkaline/standard). DO NOT use rechargeable batteries. DO NOT
recharge non-rechargeable batteries. DO NOT short-circuit the supply terminals.
5
Set the Time, Date & Units
Press the “SET” button, located on the front of the display, to enter SET MODE.
Once in set mode, the preference you are currently setting will blink on the
display.
To adjust the currently selected (flashing) item, press and release the “T“ or
“V “ buttons (press and HOLD to fast adjust).
To save your adjustments, press and release the “ SE T ” button again to adjust
the next preference. The preference set order is as follows:
TOP DISPLAY:
CLOCK HOUR
CLOCK MINUTE
CALENDAR MONTH
CALENDAR DATE
CALENDAR YEAR
TEMPERATURE UNITS (ºF or ºC)
WIND SPEED UNITS (MPH, KPH, Knots)
RAINFALL UNITS (in or mm)
PRESSURE UNITS (inHg or hPa)
TICKER DISPLAY:
LANGUAGE (English, French, Spanish)
WEATHER TICKER SPEED (SLOW, MEDIUM, FAST)
PC CONNECT MODE (1, 2, 3, 4)
You will automatically exit SET MODE if no buttons are pressed for 20 seconds.
Enter setup mode at any time by pressing the “ SE T ” button.
Display Backlight Settings
This weather station’s color display features three different lighting settings:
High (100%) brightness, Medium (60%) brightness and Low (30%) brightness.
Using battery power alone, the backlight is available momentarily for 10
seconds by pressing the “ ” button.
When display is powered with the power adapter, backlight remains on at
100% brightness. Press “ ” button once to dim to 60% brightness; press again
to dim to 30%, press a 3rd time to enter “AUTO DIM” mode. “AUTO DIM” will
appear below the time.
AUTO DIM MODE: Automatically adjusts display brightness based on time of day & year.
MARCH 11- NOVEMBER 4
6:00 a.m. - 9:00 p.m. = 100% brightness
9:01 p.m. - 5:59 a.m.= 30% brightness
NOVEMBER 5 - MARCH 10 7:30 a.m. - 7:00 p.m.= 100% brightness
7:01 p.m. - 7:29 a.m. = 30% brightness
6
Placement for Maximum Accuracy
AcuRite sensors are sensitive to surrounding environmental conditions. Proper
placement of both the display and the sensor are critical to the accuracy and
performance of this product.
Display Placement
Place the display in a dry area free of dirt and dust. To ensure
accurate temperature measurement, place out of direct sunlight and
away from heat sources or vents. Display stands upright for tabletop
use or is wall-mountable.
Important Placement Guidelines
Display and sensor must be within 330 feet (100 m) of each other.
MAXIMIZE WIRELESS RANGE
lace units away from large metallic items, thick walls, metal surfaces, or other
P
objects that may limit wireless communication.
PREVENT WIRELESS INTERFERENCE
lace both units at least 3 feet (.9 m) away from electronic devices (TV, computer,
P
microwave, radio, etc.).
PC Connect
PC Connect works with PCs to provide access to your Weather Center data in
the following ways:
• Data File: The display logs (or stores) data so that you can download it to a CSV (comma separated values) data file on your PC.
• Web Browser or Smartphone: Monitor sensor data remotely using AcuRite’s
free AcuRite online software, or from a mobile device using the free AcuRite
app, available from the Apple App Store or Google Play Store.
• Weather Underground: This weather station is compatible for streaming data to the Weather Underground Personal Weather Station Network. For more information, navigate to: www.acurite.com > Support > Downloads
USB Mode
To set up PC Connect, you must first select mode 3 on your display to gain
access to all functionality. Modes 1, 2 and 4 are not used for the
PC Connect software.
1.While in normal viewing mode, press and release the “SET” button until
“PC CONNECT MODE” appears on the Weather TickerTM screen.
2.Press and release the “T“ or “V “ buttons to select mode 3.
3.Press the “SET” button to confirm your selection. PC Connect USB Mode is now set.
7
Download the Software
The PC Connect software is available online as a free download. A manual
(PDF) is included with the software download.
Before setting up the PC Connect software, verify that the
display is ON with the power adapter
plugged in. Next, connect the mini-USB
(small end of the cable) into the USB
port on the display, located inside the
battery compartment.
PC Connect software to your computer by visiting:
1 Download
www.acurite.com > Support > Downloads
Open the file that was downloaded in step 1 and follow the on-screen
2 instructions
to install the software.
After PC Connect is installed on the computer, the initial configuration will
3 begin
automatically. Select where to save weather data downloaded from the
display. By default, this will create a folder on the computer.
prompted by the software to plug in the display, connect the
4 When
USB (larger end of the cable) into a USB port on the computer.
PC Connect is installed and ready for use.
Follow the instructions within the
PC Connect app to complete setup
and begin using the software.
8
(PC)
OPERATION
Using the Professional Weather Center
Learning Mode
Self-Calibrating Forecasting use a unique algorithm to analyze changes in
pressure over a time period (called Learning Mode) to determine your altitude.
After 14 days, the Learning Mode icon disappears from the display screen. At
this point, the self-calibrated pressure is tuned in to your location and the unit is
ready for superior weather prediction.
Weather Forecast
AcuRite’s patented Self-Calibrating Forecasting provides your personal forecast
of weather conditions for the next 12 to 24 hours by collecting data from
the sensor in your backyard. It generates a forecast with pinpoint accuracy personalized for your exact location.
STORM
LIKELY
PARTLY
CLOUDY
RAIN
LIKELY
CLOUDY
SNOW
LIKELY
CHANCE OF MIXED
RAIN & SNOW
View the complete list of icons at www.AcuRite.com/acurite-icons
Weather Select
Weather Select displays data including wind chill, dew point, heat index, feels
like, days with rain this month, and days since last recorded rainfall. To change
the “Weather Select” category shown, press the “SELECT” button on the front
of the display.
Barometric Pressure
Subtle variations in barometric pressure greatly affect the weather. This
weather center displays the current pressure with an arrow icon to indicate the
direction the pressure is trending (FALLING, STEADY, or RISING).
9
Rainfall Tracking
This weather station features enhanced tracking of historical rainfall data. Rain
accumulation data is recorded for today, over all-time, by year, by month, and
by rainfall event.
icon is shown
Press the “RAINFALL” button to review rainfall records. The
on the display while historical data is being viewed.
Records are shown in the following order:
PREVIOUS RAINFALL #1*
PREVIOUS RAINFALL #2*
PREVIOUS RAINFALL #3*
CURRENT MONTH TOTAL RAINFALL
PREVIOUS MONTH TOTAL RAINFALL
2 MONTHS AGO TOTAL RAINFALL
CURRENT YEAR TOTAL RAINFALL
PREVIOUS YEAR TOTAL RAINFALL
ALL-TIME TOTAL RAINFALL (date shown is start date of the all-time total;
the date the display was powered on)
TOTAL RAINFALL
FOR DATE SHOWN
CURRENT YEAR
TOTAL RAINFALL
TOTAL RAINFALL
FOR MONTH SHOWN
PREVIOUS YEAR
TOTAL RAINFALL
ALL-TIME
TOTAL RAINFALL
*Previous rainfall is the amount of rain recorded from 12:00am to 11:59pm on
the date shown.
10
Weather Ticker ™
The Weather Ticker automatically flashes your real-time weather information
and alerts as text in the lower part of the display screen.
The possible WEATHER TICKER messages are as follows:
HEAT INDEX-XX
WINDCHILL-XX
DEW POINT-XX
IT FEELS LIKE XX OUTSIDE
7 DAY HIGH TEMP. XX- MM/DD
7 DAY LOW TEMP. XX- MM/DD
30 DAY HIGH TEMP. XX- MM/DD
30 DAY LOW TEMP. XX- MM/DD
ALL TIME HIGH TEMP. XXX...RECORDED MM/DD/YY
ALL TIME LOW TEMP. XXX...RECORDED MM/DD/YY
24 HOUR TEMP. CHANGE +XX
ALL TIME HIGH WIND XX MPH...RECORDED MM/DD/YY
7 DAY AVERAGE WIND XX MPH
TODAY’S AVERAGE WIND XX MPH
MOON- NEW
MOON- WAXING CRESCENT
MOON- FIRST QUARTER
MOON- WAXING GIBBOUS
MOON- FULL
MOON- WANING GIBBOUS
MOON- LAST QUARTER
MOON- WANING CRESCENT
INDOOR HUMIDITY OK
INDOOR HUMIDITY HIGH
INDOOR HUMIDITY LOW
NEW LOW TEMP. RECORD XX
NEW HIGH TEMP. RECORD XX
NEW WIND RECORD TODAY XX
CURRENT RAINFALL X.XX/HR.
RAIN EVENT STARTED XX HRS. AGO
SENSOR BATTERIES LOW
DISPLAY BATTERIES LOW
SENSOR SIGNAL LOST...CHECK BATTERIES AND PLACEMENT
CAUTION- HEAT INDEX IS XXX
CAUTION- WIND CHILL IS XXX
CALIBRATION
DATA LOGGER FULL...CONNECT TO PC TO TRANSFER
11
Troubleshooting
Problem
No outdoor sensor
reception
no bars
Outdoor
temperature
is flashing or
showing dashes
Inaccurate forecast
Possible Solution
•R
elocate the display and/or the 5-in-1 sensor.
The units must be within 330 ft (100 m) of each other.
•M
ake sure both units are placed at least 3 feet
(.9 m) away from electronics that may interfere with
the wireless communication (such as TVs, microwaves,
computers, etc).
•U
se standard alkaline batteries (or lithium batteries
in sensor when temperature is below -4ºF/-20ºC). Do
not use heavy duty or rechargeable batteries. NOTE:
It may take a few minutes for display and sensor to
synchronize after batteries are replaced.
•S
ynchronize the units:
1. B
ring both the sensor and display indoors and
remove power adapter/batteries from each.
2. Reinstall batteries in outdoor sensor.
3. Reinstall power adapter/batteries in display.
4. L et the units sit within a couple feet of each other
for a few minutes to gain a strong connection.
Flashing of the outdoor temperature may be an
indication of wireless interference.
•M
ake sure the A-B-C switch in the battery
compartments of both the display and sensor are
switched to the same letter. You may choose A, B or
C; but both units must match to sync up. Sometimes
changing to a different channel can help.
•W
eather Forecast icon predicts conditions for the next
12 to 24 hours, not current conditions.
•H
as Learning Mode icon disappeared from the
display? Learning Mode must complete before
forecast and pressure will be accurate.
•A
llow unit to run continuously for 33 days. Battery
removal or resetting the display will restart Learning
Mode. After 14 days, forecast should be fairly
accurate, however Learning Mode calibrates for a
total of 33 days.
12
Troubleshooting
Problem
Possible Solution
Inaccurate
temperature or
humidity
•M
ake sure both the display and 5-in-1 sensor are
placed away from any heat sources or vents
(see page 7).
•M
ake sure both units are positioned away from
moisture sources (see page 7).
•M
ake sure 5-in-1 sensor is mounted at least 5 ft off of
the ground.
• Calibrate indoor and outdoor temperature and
humidity (see page 15).
No rainfall
• Check to ensure the rain gauge stabilizer (plastic tab)
has been removed from the bottom of the sensor.
• Clear debris, such as leaves, out of the rain collector
funnel and debris screen.
Inaccurate wind
readings
•W
hat is wind reading being compared to? Pro
weather stations are typically mounted at 30 ft high
or more. Make sure to compare data using a sensor
positioned at the same mounting height.
• Check location of the sensor. Ensure it’s mounted a
minimum of 5 ft in the air with no obstructions around
it (within several feet).
•Ensure wind cups are spinning freely. If they hesitate
or stop try lubricating with graphite powder or spray
lubricant.
USB connectivity
not working
• Verify display is in USB mode 3 (see page 7).
• Unplug USB from display to computer for 20 seconds,
and then plug back in.
•C
heck that the batteries are installed correctly.
Batteries may need to be replaced.
•R
eset the display by pressing and holding the CLEAR
RECORD/ RESET button, located on the back of the
display. Date and time will need to be entered after
a reset.
Display screen
not working
•C
heck that the power adapter is plugged into the
display and an electrical outlet.
•R
eset the display by pressing and holding the CLEAR
RECORD/ RESET button, located on the back of the
display. Date and time will need to be entered after
a reset.
13
Troubleshooting
Problem
Possible Solution
Cannot access data
online or on the
AcuRite mobile app
• Verify under Status that data was received from
the indoor display. The timestamp should update
every 18-36 seconds.
• Verify that you created an account or logged
into an existing account at www.MyAcuRite.
com or in the AcuRite app, and that you input
the display’s DEVICE ID as a part of the account
setup.
• Verify the PC that the display is connected to is
always powered ON.
• Verify the PC that the display is connected to is
always connected to the internet.
• Verify that the display’s DEVICE ID is entered
correctly in the PC Connect software on your PC.
• Verify that “Sharing” is enabled in the PC
Connect software on your PC.
• Verify that the display’s DEVICE ID is correct
in your www.MyAcuRite.com and/or AcuRite
mobile app account.
• Follow on-screen troubleshooting steps in the
PC Connect software.
No data received from
indoor display
• Verify that the USB cable is securely connected
to the display AND to the PC.
• Verify the display is powered ON.
• Restart the PC Connect software.
• Unplug the USB cable from the PC for 1 minute,
then plug the cable back in again.
• USB port may be malfunctioning, try using a
different USB port.
14
Care & Maintenance
Display Care
Clean with a soft, damp cloth. Do not use caustic cleaners or abrasives. Keep
away from dust, dirt and moisture. Clean ventilation ports regularly with a
gentle puff of air.
Calibration
The indoor / outdoor temperature and humidity readings, and barometric
pressure can be calibrated on the display to improve accuracy. Calibration can
improve accuracy when sensor placement or environmental factors impact the
data accuracy.
1. To access calibration mode, press AND HOLD the “T”, “SE T ”, and “V ”
buttons simultaneously for at least 5 seconds.
2. To adjust the currently selected (flashing) item, press and release the “T“
or “V “ buttons to calibrate the data value higher or lower from the actual
reading.
3. To save your adjustments, press and release the “ SE T ” button to adjust the
next preference. The “ ” icon will remain illuminated next to calibrated
values.
The preference set order is as follows:
OUTDOOR TEMPERATURE
OUTDOOR HUMIDITY
INDOOR TEMPERATURE
INDOOR HUMIDITY
BAROMETRIC PRESSURE (must be set to MANUAL mode to calibrate)*
*To change from AUTO to MANUAL pressure mode and vice versa, press
AND HOLD the “SET” button for at least 10 seconds. The display indicates
the current pressure mode selected,“AUTO” or “MANUAL”.
After 20 seconds of inactivity, the display will save the adjustments and exit
calibration mode. Note: Calibrations will be erased if the display is reset or if
batteries are removed and the power adapter is unplugged.
15
Specifications
DISPLAY’S BUILT-IN
TEMPERATURE SENSOR
RANGE
32ºF to 122ºF; 0ºC to 50ºC
DISPLAY’S BUILT-IN
HUMIDITY SENSOR RANGE
1% to 99%
WIND SPEED
0 to 99 mph; 0 to 159 kph
WIND DIRECTION
INDICATORS
16 points
RAINFALL
0.01 inches (0.25 mm) and up
WIRELESS RANGE
330ft / 100m depending on home construction materials
OPERATING FREQUENCY
433 MHz
POWER
5V, 250mA adapter
3 x AA alkaline batteries (optional)
DATA REPORTING
Wind Speed: 18 second updates; Direction: 36 seconds
Outdoor temperature & humidity: 36 second updates
Indoor temperature & humidity: 60 second updates
PC Connect CSV Data Logging: 12 minute intervals
PC Connect to Online Portal/App: 18 seconds
DISPLAY MEMORY
512 kilobytes (not expandable)
PC CONNECT SYSTEM REQUIREMENTS
Mac OS X 10.9 (Mavericks) or higher
Windows 10 / 8.1 / 8 / 7; 1 GHz or faster processor;
1 GB (32-bit) or 2 GB (64-bit) of RAM; available USB port
High speed internet is required for some advanced
features of PC Connect, such as Weather Underground
Rapid Fire Updates.
FCC Information
This device complies with part 15 of FCC rules. Operation is subject to the following two conditions:
1- This device may NOT cause harmful interference, and
2- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could
void the user authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation of the device.
16
Customer Support
AcuRite customer support is committed to providing you with best-inclass service. For assistance, please have the model number of this
product available and contact us in any of the following ways:
(844) 228-5465
Visit us at www.AcuRite.com
► Installation
Videos
► Register
your Product
► Instruction
Manuals
► Support
User Forum
► Replacement
Parts
► Submit
IMPORTANT
Feedback & Ideas
PRODUCT MUST BE REGISTERED
TO RECEIVE WARRANTY SERVICE
PRODUCT REGISTRATION
Register online to receive 1 yearwarranty protection
www.AcuRite.com
Limited 1-Year Warranty
We expressly disclaim all liability for special, consequential,
or incidental damages, whether arising in tort or by contract
from any breach of this warranty. Some states do not allow the
exclusion or limitation of incidental or consequential damages,
so the above limitation or exclusion may not apply to you.
AcuRite is a wholly owned subsidiary of Chaney
Instrument Company. For purchases of AcuRite
products, AcuRite provides the benefits and services set
forth herein. For purchases of Chaney products, Chaney
provides the benefits and services set forth herein.
We further disclaim liability from personal injury relating to
our products to the extent permitted by law. By acceptance of
any of our products, the purchaser assumes all liability for the
consequences arising from their use or misuse. No person, firm
or corporation is authorized to bind us to any other obligation
or liability in connection with the sale of our products.
Furthermore, no person, firm or corporation is authorized
to modify or waive the terms of this warranty unless done in
writing and signed by a duly authorized agent of ours.
We warrant that all products we manufacture under this
warranty are of good material and workmanship and, when
properly installed and operated, will be free of defects for a
period of one year from the date of purchase.
Any product which, under normal use and service, is proven
to breach the warranty contained herein within ONE YEAR
from date of sale will, upon examination by us, and at our sole
option, be repaired or replaced by us. Transportation costs and
charges for returned goods shall be paid for by the purchaser.
We hereby disclaim all responsibility for such transportation
costs and charges. This warranty will not be breached, and we
will give no credit for products which have received normal
wear and tear not affecting the functionality of the product,
been damaged (including by acts of nature), tampered,
abused, improperly installed, or repaired or altered by others
than our authorized representatives.
In no case shall our liability for any claim relating to our
products, your purchase or your use thereof, exceed the
original purchase price paid for the product.
Applicability of Policy
This Return, Refund, and Warranty Policy applies only to
purchases made in the United States and Canada. For
purchases made in a country other than the United States or
Canada, please consult the policies applicable to the country in
which you made your purchase.
Remedy for breach of this warranty is limited to repair or
replacement of the defective item(s). If we determine that repair
or replacement is not feasible, we may, at our option, refund
the amount of the original purchase price.
Additionally, this Policy applies only to the original purchaser
of our products. We cannot and do not offer any return,
refund, or warranty services if you buy products used or from
resale sites such as eBay or Craigslist.
THE ABOVE-DESCRIBED WARRANTY IS THE SOLE WARRANTY
FOR THE PRODUCTS AND IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED. ALL OTHER WARRANTIES
OTHER THAN THE EXPRESS WARRANTY SET FORTH HEREIN
ARE HEREBY EXPRESSLY DISCLAIMED, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTY OF MERCHANTABILITY
AND THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR
PURPOSE.
Governing Law
This Return, Refund, and Warranty Policy is governed by the
laws of the United States and the State of Wisconsin. Any
dispute relating to this Policy shall be brought exclusively in the
federal or State courts having jurisdiction in Walworth County,
Wisconsin; and purchaser consents to jurisdiction within the
State of Wisconsin.
17
18
19
Weather
Stations
Temperature
& Humidity
Weather
Alert Radio
Kitchen
Thermometers
& Timers
Clocks
It’s More than Accurate, it’s
AcuRite offers an extensive assortment of precision instruments,
designed to provide you with information you can depend on to
Plan your day with confidence™.
www.AcuRite.com
Printed in China
06037 INST 062016
©Chaney Instrument Co. All rights reserved. AcuRite is a registered trademark of
the Chaney Instrument Co., Lake Geneva, WI 53147. All other trademarks and copyrights are the property of their respective owners. AcuRite uses patented technology.
Visit www.AcuRite.com/patents for details.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement