Sangean HDR-18 User manual

Sangean HDR-18 User manual
HDR-18
GB
Version 1
HD Radio technology manufactured under license from iBiquity Digital
Corporation. U.S. and Foreign Patents. HD Radio™ and the HD, HD
Radio and “Arc” logos are proprietary trademarks of iBiquity Digital Corp.
VERY IMPORTANT PLEASE READ
Sangean suggest that you keep your AC Adapter at least 12 inches
away from the radio while listening to the AM Band.
Your Sangean Radio is powered by an AC adapter which is a
“switching” or “switch-mode” type. The DOE (Department Of Energy)
has a Federal mandate; requiring all manufactures to use this type
of power supply. This newer power saving technology has the
unfortunate side effect of causing interference to the AM radio band.
Therefore, we recommend that customers keep at least a 1 foot
distance between the AC adapter and the radio. This interference
will not affect the FM Band. If you have any questions please
contact customer service at (888)726-4326, (562)941-9900 or
[email protected]
If an AC adapter isn’t included in this model and if you wish to
purchase an AC Adapter separately, please refer to the specifications
for the AC Adapter stated on the final page of the manual, or please
contact Sangean for the correct AC Adapter and specifications.
To learn more about the DOE mandate please visit http://www1.
eere.energy. gov/buildings/appliance_standards/product.aspx/
productid/23
1
IMPORTANT NOTE:
To comply with the FCC RF exposure compliance requirements, no
change to the antenna or the device is permitted. Any change to the
antenna or the device could result in the device exceeding the RF
exposure requirements and void user’s authority to operate the device,
and all warranties.
CAUTION:
To reduce the risk of the electric shock, do not perform any servicing
other than that contained in the operating instructions unless you are
qualified to so.
Please note not all AC adapters are alike.
The AC adapter that is included with this radio is designed to be used
exclusively with this device. Do not use an AC adapter that differs
from the specifications on the AC adapter that is included.
If an AC adapter is NOT included with your radio and in order not
to damage the unit and void your warranty, specifications for the
AC Adapter are stated on the final page of the manual, or please
contact Sangean for the correct AC Adapter and specifications. For
customers in the US and Canada, please call 888-726-4326. For all
other areas, please contact us via [email protected]
Do not use an AC adapter that does not meet the correct
specifications.
Cautions
Do not allow this radio to be exposed to water, steam or sand. Do not leave your radio where
excessive heat could cause damage such as in a parked car where the heat from the sun can
build up even though the outside temperature may not seem too high.
●Your radio should not be exposed to dripping or splashing water and that no objects filled with
liquids, such as vases, shall be placed on the radio.
●I t is recommended to operate the product such that there is a minimum distance (4”
recommended) to adjacent objects in order to ensure good ventilation.
●The ventilation of the product should not be restricted by covering it or its ventilation openings
with items such as newspapers, tablecloths, curtains etc.
●No open flame sources such as lighted candles should be placed on the product.
●It is recommended to avoid using or storing the product at extreme temperatures. Avoid
leaving the unit in cars, on window sills or in direct sunlight etc.
GB
2
Control
1. Speaker
2. Band button
3. Preset button
4. Alarm 1 button/Preset 1
5. Sleep timer button/Preset 2
6. Dimmer button/Preset 3
7. Info button/Preset 4
3
8. HD seek up button/Preset 5
9. LCD display
10. Standby button/Power button
11. Tuning control/Select/FM/AM Seek button
12. Volume control/Tone control
13. Remote control sensor
14. HD seek down button/Preset 10
15. Menu button/Preset 9
16. Mono button/Preset 8
17. Nap timer button/Preset 7
18. Alarm 2 button/Preset 6
19. Frequency button
20. Headphone socket
Control
GB
21. External F-type FM antenna terminal
22. External AM antenna terminal
23. DC IN socket
24. REC out socket
25. AUX IN socket
26. External/Internal antenna switch
4
Control
27. Reset
5
Remote control
A. Standby button/Power button
B. Mute button
C. Key pad button1-10/0
D. Tuning up button
E. HD seek down button
F. Info button
G.Alarm 1 button
H. Nap timer button
I. Sleep timer button
J. Alarm 2 button
K. Tone button
L. Mono button
M.Dimmer button
N. Tuning down button
O.Menu button
P. HD seek up button
Q.(FM/AM) Seek button/Select button
R. Frequency button
S. Volume up/down button
T. Band button
GB
IMPORTANT:
Batteries should not be exposed to excessive heat such as sunshine, fire or the like. After use,
disposable batteries should be taken to a suitable recycling centre. On no account should
batteries be disposed of by incineration. Do not leave batteries within reach of young children,
they can be a chocking hazard.
6
Power your radio
Antenna setup for AM reception
The AC power adaptor required for this unit should be 12 volts DC at
1.5A center pin positive.
Insert the adaptor plug into the DC socket on the rear of the radio. Plug
the adaptor into a standard AC outlet.
IMPORTANT:
The AC adaptor is used as the means of connecting the radio to
the power supply. The AC Adapter used for the radio must remain
accessible during normal use in order to disconnect the radio from the
power supply completely, the AC Adaptor should be removed from the
power supply outlet completely.
This radio comes with a built-in AM Ferrite antenna which should be
enough for normal listening. To improve the AM reception, you may
connect an external AM antenna (not supplied) to the AM external
antenna terminal on the back of the unit.
Important:
If you choose to use an AM loop antenna ensure it’s located at least 20”
away from the receiver to avoid possible interference.
Antenna setup for FM reception
7
This radio comes with a built-in AM/FM antenna and has external
antenna connections.
To use the FM internal antenna, make sure to switch FM external/
internal antenna switch in the back of your radio to internal antenna
position (i.e. INTERNAL). As for external antennas, there are two types
of antennas that can be used to improve FM reception.
You can connect the supplied FM antenna to the F-type antenna
terminal and adjust the telescopic aerial for best reception.
You can also connect a 75 ohm coaxial cable of an outdoor antenna to
the terminal.
Make sure to switch external/internal antenna switch to external position
after connecting an external antenna.
Note:
In some of the European countries, you may have to use an adaptor
plug to connect with the outdoor/rooftop antenna in case your antenna
has a different type of plug.
Setting the clock
Clock setting can be done when the receiver is on or in Standby Mode
(power off).
Setting the clock manually
1.Repeatedly press the Menu button until ‘Clock Update’ is shown on
the display.
2.Rotate the Tuning control knob to select ‘Manual’ and press the Tuning control knob to enter the clock time setting. The hour digit will be
highlighted on the display.
3.Rotate the Tuning control knob to set the desired hour. Then press
the Tuning control knob to confirm the setting. The minute digit will be
highlighted on the display.
4.Rotate the Tuning control knob to set the desired minute and press
the Tuning control knob to confirm the setting. Now the month digit
will be highlighted on the display.
5.Follow the steps above to set the month/day/year setting. When the
clock time setting is completed, your radio will exit the menu.
Auto clock set mode
Scan tuning FM / AM
1.Repeatedly press the Menu button until ‘Clock Update’ is shown on
the display.
2.Rotate the Tuning control knob to select ‘Auto’ and press the Tuning
control knob to confirm the setting. Your radio will synchronize its
clock time whenever it tunes to a radio station using RDS with CT
signals.
1.M ake sure the FM antenna is set up in advance and internal or
external switch is selected.
2.Press the Standby button to switch on your radio.
3.Press the Band button repeatedly to select the desired frequency
band.
4.To scan up in frequency, first rotate the Tuning control knob in a
clockwise direction and then press the Tuning control knob. Your
radio will scan in an upwards direction (low frequency to high
frequency) and stop automatically when it finds a station of sufficient
strength. To scan down in frequency, first rotate the Tuning control
knob in a anti-clockwise direction and then press the Tuning control.
Your radio will scan in a downwards direction and stop automatically
when it finds a station of sufficient strength.
5.After a few seconds the display will update. The display will show the
frequency of the signal found. If the signal is strong enough and there
is RDS/RBDS data present then the radio will display the station
name.
Setting the time format
1.Repeatedly press the Menu button until ‘Set 12/24 hour’ is shown on
the display.
2.Rotate the Tuning control knob to select 12 or 24 hour format. The
selected format is used in standby mode, on the playing mode screen
and when setting the alarms.
Operating the radio
This radio is equipped with four tuning methods – Scan tuning, Manual
tuning, Memory presets recall and Direct Entry.
Manual tuning – FM / AM
1.Press the Standby button to switch on your radio.
2.Press the Band button repeatedly to select the desired frequency
band.
3.Rotate the Tuning control knob to tune to a station. The frequency will
change in steps of 50kHz/100kHz/200 kHz in FM or 9 kHz/10 kHz in
AM.
4.When the frequency band end is reached the radio will recommence
tuning from the opposite frequency band end.
5.Adjust the Volume control to the desired volume settings.
6.To switch off your radio press the Standby button.
Note:
If your radio has any interference in the AM band because of its
adaptor, please move your radio away from its AC adaptor at least 12”.
8
GB
Presetting stations
There are 10 presets each for FM and AM radio. They are used the same way for each operating
mode.
1.Press the Standby button to switch on your radio.
2.Tune to the required radio station as previously described.
3.To store the station as a preset, press and hold the Preset button and the display will show
“Preset Store”.
4.Press and release the required preset number button.You will hear a beep and the station
will be stored under the chosen preset. The display will show “Preset 3 stored”, for example.
Repeat this procedure as needed for the remaining presets.Alternatively, you can rotate the
Tuning control knob to choose your required preset number and press the Tuning control knob
to confirm your selected preset number.
5.Stations which are already stored in the presets may be overwritten by following the above
procedure.
Recalling a preset station
1.Press the Standby button to switch on your radio.
2.Select the required operating mode using the Band button.
3.Momentarily press the Preset button and then press the required preset number. Your radio
will then tune to the station stored in the selected preset memory. The chosen preset number
is shown in the upper area of the radio display, e.g. ‘M3’. Alternatively, you can press the
Preset button and rotate the Tuning control knob to select your required preset number. Then,
press the Tuning control knob to tune to the station stored in the selected preset memory.
Direct Entry Tuning
9
You can directly tune to a radio station by entering the station frequency.
For example, to tune to station 93.3 FM, press the Band button to select the FM band followed by
pressing the FREQ button and the numerical buttons 9-3-3. To tune to 1120 AM, press the Band
button to select the AM band, followed by pressing the FREQ button and the numerical buttons
1-1-2-0.The display will show ‘Error’ if the input frequency is incorrect or out of coverage.
Stereo / Mono switching
Receiving HD Radio stations
If the FM radio station being listened to has a weak signal, some hiss
may be audible. It is possible to reduce this hiss by forcing the radio to
play the station in mono rather than stereo.
1.Press the Band button as needed to select FM radio mode and tune
to the required FM station as previously described.
2.Press the Mono button to switch to mono or stereo.
When the radio is tuned to an HD Radio station, the HD Radio logo will
flash in the display, indicating that the signal is blending from analog to
digital. Once the receiver acquires the HD Radio signal, the HD Radio
logo will remain solid on the screen.
Tuning region
When the radio is tuned to an HD Radio station, it will determine that
one or more Multicast stations are available and “HD1+”, for example,
may appear on the display. “HD1” indicates the number of the current
multicast program and plus (+) means that additional HD Radio
programs are available. Rotate the Tuning control knob on the radio (or
the Tuning up/down button on the remote control) to tune to HD2/HD3
Multicast channel.
Your radio can be configured for any one of the four international tuning
regions.
1.Press the Band button to select your required frequency band.
2.Repeatedly pressing the Menu button until ‘Tuning Region’ is shown
on the display.
3.Rotate the Tuning control to select your required tuning region and
then press the Tuning control knob to confirm your selection.
Region A (Most countries)
FM: 87.5-108, 100 kHz
Region A (Philippines, Romania)
AM: 522-1710, 9kHz
Region B (US, Mexico, Canada)
FM: 87.5-107.9, 200kHz
Region B (US, Mexico, Canada)
AM: 520-1710, 10kHz
Region C (Most countries)
FM: 87.5-108, 50 kHz
Region C (SE Asia)
AM: 522-1620, 9kHz
Region D (Brazil, Japan)
FM: 76-108, 100kHz
Region D (Brazil)
AM: 522-1629, 9kHz
Receiving Multicast Stations
HD SEEK function
Using the HD Seek Up/Down button, the radio will seek to the next
available HD Radio station. This function will also scan to the Multicast
program if available.
Press and release the HD Seek Up/Down button will tune to the next
available HD Radio station of sufficient signal strength.
10
GB
Emergency alert (EA)
Emergency Alerts (EA) is a warning system used by broadcasters to notify listeners about
potential hazardous situations related to extreme weather, floods, infrastructure failures, amber
alerts (child abductions), and more.
Your Radio must be in a location that allows for adequate reception of audio and data services
and tuned to a station that provides the Emergency Alerts.
When enabled, the Emergency Alerts feature allows audio and text-based alerts to be played or
displayed by the radio; the alerts can also awaken the radio from standby mode.
Emergency alerts setting
1.Repeatedly press the Menu button until ‘Emergency Alerts’ shown on the display.
2.Rotate the Tuning control knob to select ‘On’ to enter the Emergency Alerts Location setting.
Then press the Tuning control.
3.Rotate the Tuning control knob to select your required location setting.
If you choose ‘Off’: all the alerts that are broadcast within the radio’s range will be received.
The default setting is ‘Off’.
If you choose ‘On’: you can define the location, then the receiver will display text alerts (or
awaken the radio from standby mode) only when the received data included location-matching
alerts. If location data is not included in the received data, then the receiver disregards the
locations that are defined in the receiver.
4.Now you choose your required location preset you would like to setup. Rotate the Tuning
control knob to highlight your required location preset and press the Tuning control knob to
confirm your selection. Up to 10 locations can be saved.
11
5.There are three options for Alert Location: State/ County, Zip and Off.Rotate the Tuning
control knob to select your desired Alert Location option and then press the Tuning control
knob to enter the setting.
If State/County was selected:
1) Rotate the Tuning control knob to change the State and press the Tuning control knob to
confirm the setting.
2) Rotate the Tuning control knob to change the County and press the Tuning control knob to
confirm the setting.
If Zip was selected:
Rotate the Tuning control knob to select the digit (+ -) and press the Tuning control knob
to move the (+ -) to the next digit. Continue to change all of the digits in the Zip. Press the
Tuning control knob to confirm the setting.
If Off was selected: the current Location preset will be disabled.
6.After completing your EA setting, it is necessary to tune to an HD Radio station (AM or FM)
GB
which supports Emergency alerts (it is indicated with ‘Steady up-pointing triangle (
)’ on
the top right corner of the screen), in order to receive an alert. If you want to receive the EA
in the Standby mode, make sure the radio is in an environment that it can receive HD Radio
broadcast signals properly. Please note that EA can only be received when the radio is in AM/
FM and in the Standby mode.
When your radio detects an EA
Once the radio detects an alert, it will sound an alert tone, display the alert category (e.g,
Weather, Hazmat, etc.), and scroll the alert text.
Repeatedly press the Info button to view the “Emergency Alerts History”.
Use the HD Seek up/down buttons to scroll through the history, which contains the five most
recent Emergency alerts.
12
Snoozing and ignoring an EA
Indicators for Emergency alerts
Once the alert is triggered, the EA will remain on the display until the
user snoozes or ignores the alert by pressing any button. The EA will
be shown in the “Emergency Alerts History” after snoozing/ ignoring is
activated.
Your radio may display various EA indicators on the top right
corner of the display.
Snooze an EA: Press and release any button other than the Standby
button will snooze the EA for 10 minutes. Before the “snooze” time has
expired, no alert functionality will be triggered. However, if a new alert
message is received, “snooze” will be cancelled immediately.
Ignore an EA: Press and hold any button or press and release the
Standby button will ignore the EA for 12 hours .Before the “ignore” time
has expired, no alert functionality will be triggered. However, if a new
alert message is received, “ignore” will be cancelled immediately.
Steady up-pointing triangle (
Current station supports
Emergency Alerts
)
Flashing up-pointing triangle(
)
Emergency Alerts message
“ignored”
Alternating up- down triangle (
)
Emergency Alerts message
“snoozed”
Flashing up-pointing test indicator Test Alerts message OK and
“ignored”
(
)
Alternating up-down test indicator
(
13
Emergency Alerts feature is
disabled
Exclamation mark (!)
)
Test Alerts message OK and
“snoozed”
Display options
Press the Info button to cycle through the various modes.
a. Radio display
RDS status
GB
1
RDS indicator
5
Signal strength indicator
1
2
Station Frequency
6
Station name
2
3
Radio Text
7
Call sign
4
Stereo indicator
8
Program type
3
4
5
6
7
8
HD Radio status
1
Multicast set index
7
Program type
2
HD Radio indicator
8
Stereo indicator
3
Preset number
9
Signal strength indicator
4
Station Frequency
10 Emergency alerts indicator
Plus (+) indicator: additional HD Radio
stations are available
5
Station name
11
6
Artist
12 Title
1
2
3
8
4
5
10
6
7
9
11
12
14
b.Guide mode (If the radio is tuned to an HD Radio station with Multicasts)
d. Clock
e. Emergency Alerts History (if alerts have occurred)
Setting the alarm clock
Your radio has 2 separate alarms which can be set to wake you to FM, AM or buzzer. Each alarm
can be set to sound once, daily, on weekdays or weekends. The alarms can be set whether the
radio is in use or in standby mode. Ensure that the time is set correctly before setting the alarms.
Note: If no buttons are pressed for 10 seconds, the radio will exit the alarm setup.
1.Press and hold the Alarm 1 button, for example, until you hear a beep. “Alarm 1” will show on
the display.
2.Rotate the Tuning control knob to select ‘On’ or ‘Off’. If ‘Off’ is selected any current setting for
that alarm will be cancelled. With ‘On’ selected, press and release the Tuning control knob to
cause the alarm hour digits to highlight on the display.
3.Rotate the Tuning control knob to choose the desired hour for the alarm and press the Tuning
control knob to cause the minute digits to highlight on the display.
4.Rotate the Tuning control knob to choose the desired minute for the alarm and press the
Tuning control knob to confirm the setting. The display will show the frequency options for the
alarm.
‘Once’- the alarm will sound once
‘Weekdays’-the alarm will sound on weekdays only
‘Weekends’- the alarm will sound only at weekends
‘Daily’-the alarm will sound everyday
Rotate the Tuning control knob to select your required frequency and press the Tuning control
knob to confirm your setting.
15
Disabling/canceling alarm setting
5.Rotate the Tuning control knob to choose the desired source for the
alarm (FM, AM or BUZZER). Press the Tuning control knob to confirm
the setting. If setting alarm to Buzzer proceed to step 7.
6.When selecting the alarm for FM or AM, rotate the Tuning control
knob to choose your required wake-up station or press the desired
Preset button (1-10). Then press the Tuning control knob to confirm
your selection.
7.Rotate the Tuning control knob to choose your desired volume and
press the Tuning control knob to confirm the setting. Your radio will
show ‘Alarm 1 Saved’ for instance and exit the alarm setting screen.
The ‘Alarm 1’ indicator
will show on the display.
8.To view or quick change the On/Off status of the alarm, press and
release the Alarm 1 (or Alarm2) button.
When the alarm sounds
To cancel a sounding alarm, press the Standby button to cancel a
sounding alarm.
When the buzzer alarm activates, the alarm will start softly and
gradually increase in level. It will sound for 1 minute and silence for 1
minute in repetition for 60 minutes unless cancelled.
When the radio alarm is activated, the alarm will go off in Humane
Waking System. It will increase its volume from 0 to your set volume.
The ‘Alarm 1’ indicator
display.
or ‘Alarm 2’ indicator
will highlight on the
To cancel the alarm setting before the alarm sounds, firstly, press the
corresponding alarm button (i.e. alarm 1 or alarm 2 button) to enter the
alarm setting screen and then press the same button again to highlight
‘Off’. The alarm indicator will disappear from the screen and the chosen
alarm will now be disabled.
Snooze
The buzzer or radio alarm can be silenced for 5 minutes by pressing
any button other than the Standby button. In order to cancel the Snooze
timer while the alarm is suspended, press the Standby button.
Sleep timer
Your radio can be set to turn off after a preset time has elapsed. The
sleep timer setting can be adjusted between 15 and 180 minutes.
1.Press and hold the Sleep timer button to enter the sleep setup. ‘Set
sleep time’ will appear on the display.
2.Rotate the Tuning control knob to select the desired sleep time . The
options are 60, 90, 120, 150, 180, off, 15, 30. Press the Tuning
control knob to confirm the setting. Use the Off option to cancel the
sleep function. Your radio will switch into standby mode after the
preset time has elapsed. An active sleep timer is shown using a sleep
timer indicator (
) on the playing display. To view the remaining
time of an active sleep timer setting, press the sleep timer button.
3.To cancel the sleep time before the preset time has elapsed and
to turn off the radio, press the Standby button to turn the unit off
manually. To cancel the sleep timer and leave the radio playing, go
back to the sleep timer settings (step 1 to 2) and select the Off option
in step 2.
4.You can view or change the On/Off status of the Sleep timer by
pressing the Sleep timer button.
16
GB
Nap timer
Loudness
1.Press and hold the Nap timer button to enter the adjustment mode.
2.Rotate the Tuning control knob to select your desired Nap time (1-120
minutes).
3.Press the Tuning control knob to confirm the setting. ‘NAP’ symbol
will show on the display.
4.To view the remaining time of an active timer setting, press the Nap
timer button. To cancel a sounding Nap timer, press the Standby
button. If any button other than the Standby button is pressed when
the alarm is sounding, snooze function will be activated. To cancel
the function when countdown is progressing, go to nap timer setting
menu and select ‘Off’.
5.You can view or change the On/Off status of the Nap timer by
pressing the Nap timer button.
You can get compensation on lower and higher frequency for your radio
by adjusting the Loudness function.
1.Repeatedly pressing the Menu button until ‘Loudness’ is shown on
the display.
2.Rotate the Tuning control knob to select ‘On’ to turn on the loudness
function or ‘Off’ to turn off the function.
3.Press the Tuning control knob to confirm the setting.
Tone control- treble and bass
You can set up a custom treble and bass setting to your liking.
1.Make sure your radio is turned on. Press the Volume control knob to
enter the bass adjustment mode.
2.Rotate the Volume control knob until the desired level (between -5
and +5) is displayed. The sound will change as you adjust the level.
Press the Volume control knob to confirm the setting. You will enter
the treble adjustment mode.
3.Rotate the Volume control knob until the desired level (between -5
and +5) is displayed. Press the Volume control knob to confirm the
treble setting.
17
Contrast
The contrast of the display can be adjusted.
1.Repeatedly pressing the Menu button until ‘Contrast’ is shown on the
display.
2.Rotate the Tuning control knob to adjust the contrast. The contrast
level indication on the screen will change at the same time. When
you find the setting that gives the best legibility for the location in
which the radio is used, press the Tuning control knob to save the
setting.
Language
Your radio can be configured to a different language.
1.Repeatedly pressing the Menu button until ‘Language’ is shown on
the display.
2.Rotate the Tuning control knob to select your required language.
3.Press the Tuning control knob to confirm your selection. The display
will change to the chosen language.
Brightness control
AUX IN input level attenuation
The brightness of the display can be adjusted when the radio is in
Standby mode or when it is in use.
In order to adjust the intensity of the display to suit the ambient room
lighting, press the Dimmer button to adjust your required brightness
level.
The input level attenuation is to allow input level reduction if the signal
from external device is too strong.
Note: remote control unit is not applicable for this operation.
1. Press Band button to select Aux in mode.
2.Repeatedly press the Menu button until ‘Attenuation’ is shown on the
display.
3.Rotate the Tuning control knob to select Attenuation on or off.
If ‘ON’ is selected, the input signal will be attenuated.
Auxiliary input socket
A 3.5mm Auxiliary input socket is provided on the rear of your radio to
permit an audio signal to be fed into the unit from an external audio
device such as an iPod, MP3 or CD player.
1.Press the Standby button to switch on your radio.
2.Connect a stereo or mono audio source (for example, iPod, MP3 or
CD player) to the Auxiliary input socket (marked ‘AUX IN’).
3.Press the Band button to select AUX IN mode and the display will
show ‘Auxiliary Input’.
4.Adjust the Volume control on your iPod, MP3 or CD player to ensure
an adequate signal and then adjust the volume on the radio for
comfortable listening.
Headphone socket
A 3.5mm Headphone socket located on the front of your radio is
provided for use with headphones. Inserting headphones automatically
mutes the internal loudspeaker.
Please be aware that the sensitivity of headphones can vary widely.
We therefore recommend setting the volume to a low level before
connecting headphones to the radio.
IMPORTANT:
1)Excessive sound pressure from earphones and headphones can
cause hearing loss.
2)To prevent possible hearing damage, do not listen at high
volume levels for long periods.
18
GB
Rec-out socket
Reset the radio
On the rear of your radio a Rec-out socket is provided for use with a
tape recording/mini disc or to allow connection to line input of a Hi-Fi
system.
The signal on the Record out socket is unaffected by the volume
control.
If your radio fails to operate correctly or some digits on the display are
missing or incomplete, please carry out the following procedure.
1.With the radio on or in Stand-By mode repeatedly press the Menu
button until ‘Factory Reset’ is shown on the display.
2.Rotate the Tuning control to select ‘Yes’ to erase all saved settings
and all settings will revert to factory default settings.
3.You can also reset your radio by inserting a toothpick or paperclip
into the reset hole located on the bottom of your radio. Simply insert
the toothpick and press the internal button once to reset your radio.
Software version
The software version display cannot be altered and is just for your
reference. With the radio on repeatedly press the Menu button until ‘Host
Version’ and ‘DSP Version’ are shown on the display and you can view
the software version on the display.
Specifications
Power requirements
Mute function
Press the Mute button on the remote control; it will mute the output from
the loudspeakers.
1.Press the Mute button to mute the sound output. The mute symbol
will show on the display.
2.Press the Mute button again or one of the Volume buttons on the
remote control, or rotate the Volume control knob on the radio to unmute the sound output. The mute symbol
display.
19
will disappear on the
Mains Power Supply:
AC 100~240 volts, 50 Hz-60 Hz DC 12V 1.5A only (switching adaptor)
Remote Control Battery: UM-4(AAA) * 2
Frequency Coverage
Region A (Most countries)
FM: 87.5-108, 100 kHz
Region A (Philippines, Romania)
AM: 522-1710, 9kHz
Region B (US, Mexico, Canada)
FM: 87.5-107.9, 200kHz
Region B (US, Mexico, Canada)
AM: 520-1710, 10kHz
Region C (Most countries)
FM: 87.5-108, 50 kHz
Region C (SE Asia)
AM: 522-1620, 9kHz
Region D (Brazil, Japan)
FM: 76-108, 100kHz
Region D (Brazil)
AM: 522-1629, 9kHz
Antenna system
Internal Antenna system:
AM built-in ferrite antenna
FM built-in telescopic antenna
Aux In socket
3.5 mm diameter stereo jack.
Input sensitivity: In 280 mVrms, Output 7W @ 100 Hz
Input impedance: 47K ohm
External antenna terminal:
AM antenna screw terminal
FM F-type antenna terminal
REC out
Output impedance: 22K ohm
Output power
7 W 10% [email protected] Hz
DC IN
12V/1.5A center pin positive
Headphones socket
3.5 mm diameter stereo jack
output power 1mW+1mW (load 32 ohm)
Dimension: W x H x D in inches: 9.4 x 4.5 x 7.2
GB
Weight: 5.7 lbs
Sangean reserves the right to amend the specification without notice.
If at any time in the future you should need to dispose of this product please note that: Waste electrical products should not be disposed
of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. (Waste
Electrical and Electronic Equipment Directive)
20
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement