5RYXX Series Fan - Monte Carlo Fans

5RYXX Series Fan - Monte Carlo Fans
Owner’s Guide and Installation Manual
ENERGY STAR approved
with bladesMC5B241, MC5B242
MC5B243, MC5B244
MC5B245, MC5B246
MC5B247, MC5B248
MC5B249, MC5B250
MC5B251, MC5B252
MC5B253, MC5B254
MC5B255, MC5B256
MC5B257, MC5B258
MC5B259, MC5B260
MC5B261
5RYXX Series Fan
UL Model No. : AC-572LF2000
Attach sales receipt to this card and retain as your proof of purchase
DATE OF PURCHASE:
RETAILER NAME:
MODEL NUMBER:
RETAILER ADDRESS:
To register your fixture, please visit our website www.montecarlofans.com
14.95 kgs
32.89 lbs
Total fan weight
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING
READ AND SAVE THESE INSTRUCTIONS
Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA
70-1999), including fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor
on one side of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be
turned upward and pushed carefully up into the outlet box.
WARNING: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
Be cautious! Read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
Make sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet
from the floor to the trailing edge of the blade.
WARNING: To Reduce The Risk Of Fire, Electric Shock, or Personal Injury, Mount To Outlet Box Marked “Acceptable for Fan Support of
31.8 kg (70 lbs) or less” And Use Mounting Screws Provided With The Outlet Box.
CAUTION: For Compliance with Local Codes and Regulations, If Installing The Secondary Support Safety Cable in the U.S., Do Not Remove Knockouts In The Outlet Box. Mount the secondary support safety cable through the reserved nail/screw hole on the outlet box to
the building structure (or the ceiling joist).
WARNING: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do
not insert foreign object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
WARNING: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.
WARNING: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed
control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
Never place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating
equipment manufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the
American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
CAUTION: To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
All set screws must be checked and tightened where necessary before installation.
Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety Glasses,
Stepladder and Wire Strippers.
Customer Service
800-969-3347
Customer Service Center
7400 Linder Ave.
Skokie, IL 60077
www.montecarlofans.com
© 2013 Monte Carlo Fan Company
2
7/1/2013
1
Before you begin installing the fan, Switch power off
at Service panel and lock service disconnecting
means to prevent power from being switched on accidentally. When the service disconnecting means
cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
4
2
3
Warning-Risk of fire, electric shock, or personal
injury. The fan in this box may be either directly
supported from a structural framing member of
a building and/or may be mounted to an outlet
box marked acceptable for fan support of of
31.8kg (70 lbs) or less. Most outlet boxes commonly used for the support of lumminaires may
not be acceptable for fan support and may need
to be replaced. Consult a qualified electrician if
in doubt.
5
BUILDING STRUCTURE METHOD
Remove Safety bar from mounting bracket by
loosing screws, sliding bar to side, and lifting it
off the 2 screws.
6
Outlet box
FAN BRACE AND OUTLET BOX METHOD
For Installation in The U.S. only
Mounting
Plate
Wood
Screws
Remove the 6 screws attaching the Mounting
neck the mounting plate. Retain the 6 screws
for re-assembly.
Secure mounting plate directly to a joist from
the buliding structure via the two knock out
holes on the outlet box. Use only the appropriate wood screws and washers included with
your fan.
Caution: Wood screws must go through into
the building joist.
Note:If Installing It In The U.S., Do Not Remove Knockouts In The Outlet Box
Install the mounting Plate to approved fan
brace and box combination use only the hardware provided with the fan brace and box.
7
8
9
Lift mounting neck to mounting Plate and align
screws.
Secure mounting neck to the mounting plate
with 6 screws to become a complete mounting
bracket.
Remove the keeper pin and cross pin.
© 2013 Monte Carlo Fan Company
3
7/1/2013
10
12
11
Place canopy and then yoke cover
over downrod. Then thread the lead
wires and safety cable from fan
through the downrod as shown.
Insert downrod into motor yoke.
Next, insert ccross pin through yoke
and downrod and secure with keeper
pin.
13
14
15
Tighten both yoke set screws evenly
to secure downrod.
Place yoke cover on top of fan housing.
Remove the shipping stabilizer by
removing the set screws and discarding.
Loosen the 2 set screws. You should
be able to put your downrod into the
yoke.
16
17
Hang assembled fan from the mounting bracket installed to ceiling in previous
step. Make sure the fan is hanging straight. Rotate fan until the tab on the Mounting bracket engages the slot on the Downrod Ball. This must be done to prevent
the fan body from rotating when the blades are in motion.
Helpful Hint: It will help to slip downrod ball into mounting bracket by slanting fan assembly and canopy.
© 2013 Monte Carlo Fan Company
4
Re-install safety bar removed in step.
3 by placing safety bar on screws,
sliding into place, and tightening the
2 screws.
7/1/2013
18
Safety cable installation
20
19
Safety Cable
Lag Screw
safety
cable
washer
3” lag
screw
lock
washer
For Canadian installation and for USA fan and
light kit combinations over 35 lbs, in both flush
and downrod modes the safety cable must be
installed into the house structure beams using
3” lag screws, washers and lock washers provided. Make sure that when the safety cable is
fully extended the lead wires are longer than
the cable and no stress is placed on the lead
ires.
Note: If installing it in the U.S., Do Not Remove
Knockouts In The Outlet Box.
21
Loosen one and remove one preassembled screw from mounting bracket. Save
screw. Lift canopy up, aligning its keyhole
slot with the preassembled screw on
mounting bracket and twist clockwise to
lock in place. Re-install the removed
screw and tighten all screws securely.
24
Loosen 2 screws and remove 1 screw
and save.
© 2013 Monte Carlo Fan Company
Make wire connections to power source using
wire nuts provided. Make sure that no filiments
are outside of the wirenut. After making the
wire connections, the wires should be spread
apart with the grounded conductor and the
equipment-grounding conductor on one side of
the outlet box and ungrounded conductor on the
other side of the outlet box.
Make wiring connections as indicated
above. Connect black and blue wire from
fan to Black or (Hot) wire from house.
Connect White wire from Fan to White
(Neutral) wire from house. Connect
Ground leads from mounting bracket and
downrod to Ground lead from house.
Refer to Safety Tips section of manual.
23
22
Install 3 screws and washers per blade
and tighten securely. Repeat for all 5
blades. (Blades sold separately)
Note: This fan includes 2 sets of 18 blade
screws in 2 different lengths depending
on the thickness of the blade selected for
use with this fan. Please select the length
that best fits the blade thickness.
Attach blade assembly to motor using
the motor screws and washers provided. Tighten screws securely.
26
25
Install the switch housing cover by
aligning the 2 screws with the 2 key
slot holes on the plate and twist to
lock into place. Install the 1 screw removed and tighten the other 2
screws securely.
5
Remove the 3 screws on the switch
housing cover and save.
7/1/2013
27
29
28
Hook
Connect plug from fan to plug from
switch housing. Make sure the plugs
are hooked together.
© 2013 Monte Carlo Fan Company
Attach capacitor onto switch housing
by preadhered double-sided foam tap
as shown.
6
Align the reverse switch preassembled
on switch housing with the long slot
on switch housing cover as shown and
then install the switch housing using
the 3 screws previously removed . Setting the reverse switch in the left hand
side will result in downward airflow
and setting the switch in the right
hand side will result in upward airflow.
7/1/2013
Trouble Shooting
,I\RXKDYHGLI¿FXOW\RSHUDWLQJ\RXUQHZFHLOLQJIDQLWPD\EHWKHUHVXOWRILQFRUUHFWDVVHPEO\LQVWDOODWLRQ
RUZLULQJ,QVRPHFDVHVWKHVHLQVWDOODWLRQHUURUVPD\EHPLVWDNHQIRUGHIHFWV,I\RXH[SHULHQFHDQ\IDXOWV
SOHDVHFKHFNWKLV7URXEOH6KRRWLQJ&KDUW,IDSUREOHPFDQQRWEHUHPHGLHGRU\RXDUHH[SHULHQFLQJGLI¿FXOW\LQ
LQVWDOODWLRQSOHDVHFDOORXU&XVWRPHU6HUYLFH&HQWHUDWWKH
QXPEHUSULQWHGRQ\RXUSDUWVOLVWLQVHUWVKHHW
Warning %HIRUH VHUYLFLQJ RU FOHDQLQJ XQLW 6ZLWFK SRZHU RII DW 6HUYLFH SDQHO DQG ORFN VHUYLFH GLVFRQQHFWLQJ
PHDQVWRSUHYHQWSRZHUIURPEHLQJVZLWFKHGRQDFFLGHQWDOO\:KHQWKHVHUYLFHGLVFRQQHFWLQJPHDQVFDQQRWEH
ORFNHGVHFXUHO\IDVWHQDSURPLQHQWZDUQLQJGHYLFHVXFKDVDWDJWRWKHVHUYLFHSDQHO
Trouble
Suggested Remedy
,IIDQGRHVQRWVWDUW
&KHFNPDLQDQGEUDQFKFLUFXLWIXVHVRUFLUFXLWEUHDNHUV
&KHFNOLQHZLUHFRQQHFWLRQVWRIDQDQGVZLWFKZLUHFRQQHFWLRQVLQVZLWFKKRXVLQJ
CAUTION0DNHVXUHPDLQSRZHULVWXUQHGRII
,I WKLV IDQ XVHV PDQXDO IRUZDUGUHYHUVH VZLWFK PDNH VXUH WKH VZLWFK LV SXVKHG ¿UPO\
HLWKHUZD\)DQZLOOQRWRSHUDWHZKHQVZLWFKLVLQWKHPLGGOH
,IWKLVIDQXVHVUHPRWHFRQWUROOHUPDNHVXUHGLSVZLWFKHVDUHVHWWLQJSURSHUO\DQGPDNH
VXUHEDWWHU\LVHIIHFWLYH
,IIDQVRXQGVQRLV\
&KHFNWRPDNHVXUHDOOVFUHZVLQPRWRUKRXVLQJDUHVQXJQRWRYHUWLJKWHQHG
&KHFNWRPDNHVXUHWKHVFUHZVZKLFKDWWDFKWKHIDQEODGHKROGHUWRWKHPRWRUDUHWLJKW
&KHFNWRPDNHVXUHZLUHQXWFRQQHFWRUVLQVZLWFKKRXVLQJDUHQRWUDWWOLQJDJDLQVWHDFK
RWKHURUDJDLQVWWKHLQWHULRUZDOORIWKHVZLWFKKRXVLQJ
CAUTION0DNHVXUHPDLQSRZHULVWXUQHGRIIEHIRUHHQWHULQJVZLWFKKRXVLQJ
&KHFNWREHVXUHOLJKWEXOELVWLJKWLQVRFNHWDQGQRWWRXFKLQJWKHJODVVVKDGH
6RPHIDQPRWRUVDUHVHQVLWLYHWRVLJQDOVIURP6ROLG6WDWHYDULDEOHVSHHGFRQWUROV
$OORZEUHDNLQSHULRGRIKRXUV0RVWQRLVHVDVVRFLDWHGZLWKDQHZIDQZLOOGLVDSSHDU
DIWHUWKLVSHULRG
,IIDQZREEOHV
,I WKLV LV D GRZQURG PRXQW IDQ PDNH VXUH WKH ULGJH RQ PRXQWLQJ EUDFNHW HQJDJHV WKH
QRWFKLQWKHGRZQURGEDOO
0DNH VXUH WKDW FDQRS\ PRXQWLQJ EUDFNHW RU PRXQWLQJ SODWH DUH WLJKWHQHG VHFXUHO\ WR
FHLOLQJMXQFWLRQER[DQGMXQFWLRQER[LVPRXQWHG¿UPO\WRFHLOLQJMRLVW
&KHFNWKDWDOOEODGHVDUHVFUHZHG¿UPO\LQWREODGHKROGHUV
&KHFNWKDWDOOEODGHKROGHUVDUHWLJKWHQHGVHFXUHO\WRPRWRU
0RVWIDQZREEOHSUREOHPVDUHFDXVHGZKHQEODGHOHYHOVDUHXQHTXDO&KHFNWKLVOHYHOE\
VHOHFWLQJ D SRLQW RQ WKH FHLOLQJ DERYH WKH WLS RI RQH RI WKH EODGHV 0HDVXUH WKLV GLVWDQFH
IURPEODGHWLSWRFHLOQJ.HHSLQJPHDVXUHZLWKLQURWDWHWKHIDQXQWLOWKHQH[WEODGH
LV SRVLWLRQHG IRU PHDVXUHPHQW 5HSHDW IRU HDFK EODGH ,I DOO EODGH OHYHOV DUH QRW HTXDO
\RXFDQDGMXVWEODGHOHYHOVE\WKHIROORZLQJSURFHGXUH7RDGMXVWDEODGHWLSGRZQLQVHUW
D ZDVKHU QRW VXSSOLHG EHWZHHQ WKH EODGH DQG EODGH KROGHU DW WKH VFUHZ FORVHVW WR WKH
PRWRU7RDGMXVWDEODGHWLSXSLQVHUWZDVKHUQRWVXSSOLHGEHWZHHQWKHEODGHDQGEODGH
KROGHU DW WKH WZR VFUHZV IDUWKHVW IURP WKH PRWRU 5HYHUVH WKH SRVLWLRQ RI WKH ZDVKHU LI
EODGHVPRXQWIURPWRSRIEODGH
,IEODGHZREEOH LV VWLOO QRWLFHDEOHLQWHUFKDQJLQJWZR DGMDFHQWVLGH E\VLGH EODGHVFDQ
UHGLVWULEXWHWKHZHLJKWDQGSRVVLEO\UHVXOWLQVPRRWKHURSHUDWLRQ
,IOLJKWGRHVQRWZRUN &KHFNEOXHZLUHIURPIDQWRPDNHVXUHLWLVFRQQHFWHGWRKRWZLUHIURPKRXVH
&KHFNIRUORRVHRUGLVFRQQHFWHGZLUHVLQIDQVZLWFKKRXVLQJ
&KHFNIRUORRVHRUGLVFRQQHFWHGZLUHVLQOLJKWNLW
&KHFNIRUIDXOW\OLJKWEXOEDQGPDNHVXUHEXOELVWLJKWLQVRFNHW
5HPRYHOLJKWNLWDQGFKHFNWKHSOXJFRQQHFWLRQVLIWKH\DUHSUHVHQW
,IWKLVIDQXVHVUHPRWHFRQWUROOHUPDNHVXUHGLSVZLWFKHVDUHVHWWLQJSURSHUO\DQGPDNH
VXUHEDWWHU\LVHIIHFWLYH
CAUTION 0DNH VXUH PDLQ SRZHU LV WXUQHG RII EHIRUH HQWHULQJ VZLWFK KRXVLQJ DQGRU
FDQRS\
© 2013 Monte Carlo Fan Company
7
7/1/2013
Feb.2012 New format
Jul.2013 Update for CUL regulation
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement