GE ZISB420DH Monogram® 42" Built-In Side-by-Side Refrigerator Quick Specs

Monogram ® 42" Built-In Side-by-Side Refrigerator

SECTION 1

FLUSH INSET INSTALLATION

ZISB420DH

SECTION 2

STANDARD INSTALLATION

1/4" FRAMED PANELS 3/4" OVERLAY PANELS

Product Specification Revised 5/16


OVERALL DIMENSIONS

AFTER PANEL INSTALL

44"

(111.8)

ZISB420DH


26"

(66.0)

20 5/8"

(52.4)

11 3/16"

(28.4)

84 1/2"

(214.6)

15 3/8"

(39.1)

68 5/8"

(174.3)

72 5/8"

(184.5)

* 83 1/2"

( 212.1)

*39 17/32"

(100.4)

SPECIFICATIONS

Overall Width

Overall Height

Overall Depth

Door Clearance

Cutout Width

Cutout Height

Cutout Depth

Plumbing Requirements

Shipping Weight

44" (111.8 cm) †

84 1/2" (214.6 cm) †

26" (66.0 cm) †

26 5/8" (67.6cm)

45" (114.3 cm)

85" (215.9 cm)

26 3/16" (66.5 cm)

1/4" OD copper tubing or GE

SmartConnect kit

725 lb (328.9 kg)

† Dimensions include 3/4" custom cabinet panel

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended.

Install a properly grounded 3-prong electrical receptacle recessed into the back wall.

FRONT VIEW

4"

(10.2)

Use leveling legs and wheels for maximum 1" height adjustment from shipping height. Nominal installation height is 84".

41"

(104.2)

Case width

SIDE VIEW

**13"

(33.0)

**19"

(48.3)

*115° Door swing

Doors can be adjusted to

90° door swing

26 5/8"

(67.6)

TOP VIEW

** Allow

4"

(10.2) min

clearance to a wall

for 90˚ door swing

** Allow

4"

(10.2) min

clearance to a wall

for 90˚ door swing

** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door

swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow

a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan

access is maintained, but pan removal is restricted.

Dimensions in parentheses are in centimeters unless otherwise noted.

Actual product dimensions may vary due to manufacturing tolerances.

ZISB420DH Product Specification Revised 5/16

Monogram ® 42" Built-In Side-by-Side Refrigerator ZISB420DH

FLUSH INSET INSTALLATION 3/4" PANELS

47 1/2"

(120.7)

5 1/4"

(13.3)

E

TOP VIEW

Case 3 1/4"

Finished cleats

(8.3)

Case Trim

Door

3/4" Panel

26 3/16"

(66.5)

Flush inset depth

20 15/16"

(53.2)

5"

(12.7)

3/4"

(1.9)

Width of side cleats

45"

(114.3) Flush inset width

43 1/2"

(110.5)

Width between cleats

(212.1-214.6)

*Trim will overlap additional 7/16"

6"

(15.2)

E

75"

(190.5 )

From floor to bottom of electrical area

5"

(12.7)

Finished cleats

19"

(48.3)

85"

(215.9)

85"

(215.9)

24"

(61.0)

1 1/2"

(3.8)

1/2"

(1.3)

A

75"


5"

(12.7)

5"

(12.7)

3 1/2"

(8.9)

WATER

FRONT VIEW

3 1/2"

(8.9)

7"

(17.8)

B

7"

(17.8) SIDE VIEW

W

SIDE VIEW

W WATER

FRONT VIEW

ANTI-TIP BRACKET

C

D

2" x 4"

Cut to 35" Length


7/16"

NOTES

A Mounting the junction box in this location will also allow for front accessibility through access panel.

B Water supply area.

WARNING:

The refrigerator is top heavy and must be secured to prevent the possibility of tipping forward. Failure to do so may result in death or serious injury.

The information below is for cabinet design only. When installing the antitip system you must use the product installation instructions.

Determine your installation construction and required anti-tip configuration:

3 1/2"

(8.9)

C Cut a 1" x 4" block 35" long. Measure and mark under the soffit,

5 1/4" from the front edge of the cabinet. Secure the wood block under the soffit. From the bottom of the block to the finished floor should measure 84".

D Wooden Wall Studs and No Soffit

• Cut a 2" x 4" block and secure to brackets provided.

• Secure brackets to back wall of opening at 84" or your installation height from the floor.

See Installation Instructions for detailed instructions.

SOFFIT

FLUSH INSTALLATION

ZISB420DH

Screws mounted into vertical wall studs

*84"

(213.4)

*Or installation height from floor

SIDE VIEW INSTALLED

UNDER SOFFIT


WITH WOODEN WALL STUDS

AND NO SOFFIT

ZISB480DX



FLUSH INSET INSTALLATION 1/2" PANELS

47 1/2"

(120.7)

5 3/8"

(13.7)

E

TOP VIEW

Case 3 1/4"

Finished cleats

(8.3)

Case Trim

Door

1/2" Panel

26 3/16"

(66.5)

Flush inset depth

20 13/16"

(52.9)

5"

(12.7)

3/4"

(1.9)

Width of side cleats

45"

(114.3) Flush inset width

43 1/2"

(110.5)

Width between cleats

(212.1-214.6)


6"

(15.2)

E

75"

(190.5 )


5"

(12.7)

Finished cleats

19"

(48.3)

85"

(215.9)

85"

(215.9)

5"

(12.7)

SIDE VIEW

W

WATER

FRONT VIEW

3 1/2"

(8.9)

24"

(61.0)

1 1/2"

(3.8)

1/2"

(1.3)

A

75"


5"

(12.7)

3 1/2"

(8.9)

7"

(17.8)

B

WATER

FRONT VIEW

7"

(17.8) SIDE VIEW

W


C

SOFFIT

D

2" x 4"



7/16"

NOTES



WARNING:


The information below is for cabinet design only. When installing the antitip system you must use the product installation instructions.


3 1/2"

(8.9)

C Cut a 1" x 4" block 35" long. Measure and mark under the soffit,

5 3/8" from the front edge of the cabinet. Secure the wood block under the soffit. From the bottom of the block to the finished floor should measure 84".

D Wooden Wall Studs and No Soffit



See Installation Instructions for detailed instructions.

FLUSH INSTALLATION

ZISB420DH


*84"

(213.4)



UNDER SOFFIT



AND NO SOFFIT

ZISB480DX



FLUSH INSET 3/4" PANEL DIMENSIONS

A

PANEL DIMENSIONS

Grille Panel B

D E

A

44"

B C D E

11 3/16" 68 5/8" 16 7/8" 26 7/8"

Dispenser

Cutout

F

G

C

Dispenser

Cutout

15 3/8"

(39.1)

DISPENSER CUTOUT

POSITION

F G

17 23/32" 3 3/8"

9 5/8"

(24.4)

Freezer

Panel

Fresh

Food

Panel

3/4" RAISED DOOR PANEL ROUTING

DETAIL TOP

3/4"

11/32"

1/4"

1/4" 7/16"

NOTE: Routed areas should be finished as they may be visible when assembled.

Front

TOP

ZISB420DH


NOTES

Trimmed refrigerators are designed to be customized with decorative panels.

Field-installed 1/2" or 3/4" custom door and grille panels are required. For 3/4" raised door and grille panels, routing is required.

The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame” routing allowing the panels to slide into the attached door and grille trims.

Maximum total panel weight:

• Fresh food door panels – 75 lbs.

• Freezer drawer panel – 53 lbs.

• Grille panel – 18 lbs

Note: For panels constructed with rails and stiles (5-panel), the rails must be a minimum of 3" wide and stiles must be a minimum of

4" wide.

Door Handles

Door handle not included. A custom handle supplied by your cabinet maker may be used.

ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle – 30 1/2" long.

ZKHSS2: European tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle – 64 1/4" long.

Back

Back Front

3/16"

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

DETAIL BOTTOM

DETAIL HINGE

SIDE

ROUTER DEPTH 1/4"

2 1/16"

Front

HINGE

SIDE

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

3/16"

DETAIL HANDLE

SIDE

HANDLE

SIDE

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)



3/4" RAISED GRILLE PANEL ROUTING

NOTE: Routed areas should be finished as they may be visible when assembled.

Front

DETAIL TOP

TOP

2"

LEFT

SIDE

Back

CORNER VIEW SHOWING

“PICTURE FRAME” ROUTING

DETAIL

LEFT SIDE


2 1/16"

Back Front

3/16"

DETAIL BOTTOM

BOTTOM

3/4" PANEL SIDE VIEW

(AFTER ROUTING)

Front

Back

3/4" PANEL BOTTOM VIEW

(AFTER ROUTING)

DETAIL RIGHT

SIDE


2 1/16"

RIGHT

SIDE

ZISB420DH


NOTES

Trimmed refrigerators are designed to be customized with decorative panels. Field-installed 1/2" or 3/4" custom door and grille panels are required. For 3/4" raised door and grille panels, routing is required. The router depth is 1/4" all the way around the panel’s backs. Additional panel width reductions are required per the diagrams shown. This will create “picture frame” routing allowing the panels to slide into the attached door and grille trims.


• Fresh food door panels – 75 lbs.


• Grille panel – 18 lbs.


4" wide.

Door Handles

Door handle not included. A custom handle supplied by your cabinet maker may be used.

ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" panels.

Kit includes one handle – 30 1/2" long.

ZKHSS2: European tubular stainless steel handle designed to fit 3/4" panels. Kit includes one handle – 64 1/4" long.



DISPENSER TRIM A

ZISB420DH

Freezer Door

Ice/Water Dispenser

3/4" Flush Panel

3/4" OVERLAY PANEL

DISPENSER TRIM

1/4" Backer Panel

Freezer Door

.10" Spacer Panel

Ice/Water Dispenser

1/2" Overlay Panel

1/2" OVERLAY PANEL

DISPENSER TRIM

.85"

Total

Thickness

RAISED PANEL DESIGN ON DISPENSER MODELS

3/4" or 1/2" Flush Panel


NOTES

These refrigerators are supplied with a dispenser trim for flush inset panels.

A Panel Dispenser Trim:

The provided dispenser trim is designed to fit a total panel thickness of 3/4" or 0.85".

• If the panel is less than 3/4" thick, a noticeable gap may be created around the dispenser trim.

• If the panel is more than 0.85" thick, the dispenser trim cannot be secured to the door.

• The overlay panel must be constructed according to the specifications shown to achieve the correct total thickness.

• When a raised panel design is to be used, a custom middle rail is required.

16 3/4"

10 5/8"

DISPENSER TRIM

B

3/4" or .85"

Total

Thickness

C

Raised Panel Design on Dispenser Models:

When a raised panel design is to be used, a custom wide middle rail is required to accept the dispenser trim.

B • The middle rail must be wide enough to allow for the dispenser trim to overlap the opening.

C • The middle rail must be 3/4" total thickness for 3/4" panels or 0.85" total thickness for 1/2" panels to accept the dispenser trim.

SIDE VIEW CROSS SECTION

(Showing Raised Panel with

Middle Rail)



FLUSH INSET 1/2" PANEL DIMENSIONS

A

D

Grille Panel

Dispenser

Cutout

F

E

B


A B C D E

1/4" Backer Panel 39 7/8" 9 1/2" 68 3/8" 14 9/16" 24 9/16"

.10" Space Panel 39" 8 5/8" 67" 13 9/16" 23 9/16"

1/2" Overlay Panel 44" 11 3/16" 68 5/8" 16 7/8" 26 7/8"

G

Freezer

Panel

Fresh

Food

Panel

C

Dispenser

Cutout

15 3/8"

(39.1)


POSITION

F G

17 23/32" 3 3/8"

9 5/8"

(24.4)

1/4" BACKER ASSEMBLY ROUTING DIMENSIONS

Hinge Side

C C

Door

1/2"

Overlay

Panel

D

Freezer

Back

Backer with

Overlay Panel

Assembly

Fresh Food

Back

D

1/4"

Backer

Panel

.10"

Spacer

B A A B


A B

Fresh Food Panel 2 1/16" 1/16"

Freezer Panel

Grille Panel

2 1/16" 1/16"

C

1/8"

1/8"

D

1/8"

1/8"

2 1/16" 2 1/16" 1 15/32" 7/32"

A

C

Grille Back

D

B

ZISB420DH


NOTES

The 1/2" overlay panel must be secured to a .10" spacer panel and a 1/4" thick backer panel, which slides into the trim.

Assemble the panels with glue and screws:

• Center the spacer panel on the backer panel, left to right and top to bottom.

Secure the panels with glue.

• Refer to the chart for locating the backer panel to the overlay panel. Secure the overlay panel to the backer panel with glue and screws. Screws must be countersunk into the backer panel.


• Fresh food door panel – 75 lbs.


• Grille panel – 18 lbs.


4" wide.



OVERALL DIMENSIONS

42"

(106.7)

(106.7)

ZISB420DH


25 1/2"

(64.8)

(64.8)

23 7/8"

(60.7)

(60.7)

(213.4)

(213.4) (

( 212.1)

212.1)

(174.0)

(174.0)

(101.6)

(101.6)

SPECIFICATIONS

Overall Width

Overall Height

Overall Depth

Door Clearance

Cutout Width

Cutout Height

Cutout Depth

Plumbing Requirements

42" (106.7 cm)

84" (213.36 cm)

25 3/8" (64.453 cm)

28 5/8" (72.1 cm)

41 1/2" (105.4 cm)

83 1/2" - 84 1/2"

(212.1 - 214.6 cm)

24" (61 cm)

1/4" OD copper tubing or GE

SmartConnect kit

725 lb (328.9 kg) Shipping Weight

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply is required. An individual properly grounded branch circuit or circuit breaker is recommended.

Install a properly grounded 3-prong electrical receptacle recessed into the back wall.

(9.5)

(9.5)

FRONT VIEW

1" height adjustment from shipping height.

41"

(104.2)

Case width

Case width

** Allow

** Allow

13"

(33.0) min

(33.0) min

(8.9)

(8.9)

** Allow

** Allow

19"

(48.3) min

(48.3) min

(67.6)

(67.6)

4"

(10.2) min

4"

(10.2) min

door swing

door swing

door swing

door swing

** These refrigerators are equipped with a 2-position door stop. The factory-set 130° door

swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow

full 130° door swings for pan removal. If the 90° door stop position is used, pan access is

maintained, but pan removal is restricted.

Dimensions in parentheses are in centimeters unless otherwise noted.

ZISB420DX



STANDARD INSTALLATION

(212.1-214.6)


24"

(61)

1 9/16"

(3.97)

47 1/2"

(120.7)

20"

(50.8)

E

7/16"

(1.1)

Trim overlap

SIDE VIEW


C

SOFFIT

WATER

(8.9)

*84 1/2"

75"

From floor to bottom of electrical

(214.6) area


D


UNDER SOFFIT



AND NO SOFFIT

ZISB480DX

TOP VIEW

24"

(61.0)

1 1/2"

(3.8)

6"

(15.24)

41 1/2"

(105.4)

A

18"

(45.7)

E

5"

(12.7)


ZISB420DH

2" x 4"



*84"

(213.4)


7/16"

(1.1)

Trim overlap

75"

(190.5 )


5"

(12.7)

B

5"

(12.7)

3 1/2"

W

WATER

SIDE VIEW

FRONT VIEW

3 1/2"

The refrigerator will project forward, slightly beyond adjacent cabinetry.

Top Case Trim

Side View Top

Case Trim

Install Screws

Through Trim and Into

3/4" Min. Wood Brace

FRONT VIEW INSTALLED

WITH METAL WALL STUDS

AND NO SOFFIT

E

3/4"

Min.


NOTES



WARNING:


The information below is for cabinet design only.

When installing the antitip system you must use the product installation instructions.


C Installed Under Soffit

After installing unit into installation opening, raise grille panel and screw metal case sides to adjacent cabinet. When installed under a soffit, the soffit cannot exceed 24" deep. The top case trim overlaps the bottom of the soffit.

D Wooden Wall Studs and

No Soffit



E Metal Wall Studs and

No Soffit

This method requires securely fastened cabinets on both sides and a 3/4" minimum wood brace above unit, with it’s front surface 24" from back wall.

• After installing unit into opening, raise grille panel and attach metal case top trim to 3/4" minimum wood brace.

• The brace spanning the enclosure must be securely fastened to cabinets on both sides.

See Installation

Instructions for detailed instructions.



CUSTOM SIDE PANELS

F

24"

(61.0)

3/16"

(.5)

1 7/8"

(4.8)

(213.4)

*Depending on installation height

ZISB420DH


NOTES

F Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4" side panels will slip into the side case trim.

Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer.

*3" - 4"

(7.6 - 10.2)

*Depending on installation height

2 9/16"

(6.5)

ZIF360NXLH_ZIF360NXRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH

ZIR360NXLH_ZIR360NXRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH



1/4" FRAMED PANEL DIMENSIONS

A

D

Grille Panel

E

Dispenser

Cutout

F

B

PANEL ASSEMBLY CROSS SECTION

Trim

Door

1/4" Framed Panel

Supplied Handles

G

C


A B C D E

1/4" Framed Panel 39 7/8" 9 1/2" 68 3/8" 14 9/16" 24 9/16"

ZISB420DH


NOTES

Trimmed refrigerators are designed to be customized with decorative panels.

Field-installed custom door and grille panels are required.

1/4" Framed Panels:

For 1/4" thick custom panels ordered from your cabinet maker; the decorative panels slide into the trim.





Freezer

Panel

Fresh

Food

Panel

Dispenser

Cutout

15 3/8"

(39.1)


POSITION

F G

17 13/16" 3 1/8"

9 5/8"

(24.4)

3/4" OVERLAY PANEL DIMENSIONS

A

D

Grille Panel

E

Dispenser

Cutout

F

G

Freezer

Panel

Fresh

Food

Panel

B

C

PANEL ASSEMBLY CROSS SECTION

Trim



Door


Supplied Handles


A B C D E

1/4" Backer Panel 39 7/8" 9 1/2" 68 3/8" 14 9/16" 24 9/16"

.10" Spacer Panel 39" 8 5/8" 67" 13 1/4" 23 1/4"

3/4" Overlay Panel 40 1/8" 9 3/4" 68 5/8" 14 13/16" 24 13/16"

.25" + .10" + .75" = 1.10" Total Panel Thickness

Dispenser

Cutout

15 3/8"

(39.1)

9 5/8"

(24.4)

* DISPENSER CUTOUT

POSITION

F G

17 15/16" 3 1/4"

* Cut the dispenser opening after the backer, spacer and overlay panels have been assembled.

3/4" Overlay Panels:

For 3/4" thick custom panels ordered from your cabinet make; the decorative panels slide into the trim.

The overlay panel must be secured to a

1/4"-thick backer panel which slides into the trim. A spacer panel 0.10" thick must be placed between the overlay and backer panels.

Center each panel over the other. Assemble the panels with glue and screws. Screws must be countersunk into the backer panel.

NOTE: Left-to-right offset is not always equal to top-to-bottom offset.





Door Handles:

The supplied handles can be adjusted to accommodate both framed or overlay panels.

Custom handles of your choice, supplied by your cabinet maker, can also be installed.

ZKHPSS1: Professional tubular stainless steel handle designed to fit 3/4" overlay panels.

ZKHSS2: European tubular stainless steel handle designed to fit 3/4" overlay panels.

Kits include one handle. Order 2 kits for sideby-side refrigerators from your Monogram supplier.



DISPENSER TRIM

1/4" Framed Panel

Freezer Door

Ice/Water Dispenser

10 5/8"

DISPENSER TRIM

1/4"

Total

Thickness

1/4" PANEL DISPENSER TRIM

A


Freezer Door


Ice/Water Dispenser

1.10"

Total

Thickness


3/4" OVERLAY PANEL DISPENSER TRIM

B

RAISED OVERLAY PANEL DESIGN ON DISPENSER MODELS

16 3/4"


.10" Spacer


C

1.10”

Total

Thickness

D

SIDE VIEW CROSS SECTION

(Showing Raised Overlay with Middle Rail)


NOTES

These refrigerators are supplied with two dispenser trims, one for framed panels and one for overlay panels.

1/4" Panel Dispenser Trim:

The framed panel must be 1/4" nominal thickness to fit the dispenser trim.

• The dispenser trim fits over the custom panel and snaps into the freezer door.

• If the panel is less than 0.250" thick, a noticeable gap may be created around the dispenser trim. Foam tape may be applied on the door to improve the fit.


3/4" Overlay Panel Dispenser Trim:

The 3/4" overlay dispenser trim is designed to fit a total panel thickness of 1.100".

• If the panel is less than 1.100" thick, a noticeable gap may be created around the dispenser trim.


• The overlay panel must be constructed according to the specifications shown to achieve the correct total thickness.

• Alternative panel construction methods such as securing a 3/4" panel to a 1/4" backer panel cannot be used. Another method, routing a 3/4"-thick panel on all sides, cannot be used. These methods will not result in the required

1.100" panel thickness.

• When a raised panel design is to be used, a custom middle rail is required.

Raised Overlay Panel Design on

Dispenser Models:

When a raised panel design is to be used, a custom wide middle rail is required to accept the dispenser trim.

• The middle rail must be wide enough to allow for the dispenser trim to overlap the opening.

• The middle rail must be 1.10" total thickness to accept the dispenser trim.



FEATURES AND BENEFITS

Halogen Light Columns - Located in the freezer and fresh food compartments, extend the full length of the interior compartments providing brilliant, all-level illumination

LED Lighting - Located at the top of the fresh food compartment, and inside the vegetable and climate-control drawers, illuminates contents without compromising space

Advanced Temperature Management System

with Multi-Shelf Air Tower - Provides even distribution of air throughout the refrigerator

Climate-Control Drawer - Allows you to expresschill beverages, express-thaw meats and select specific temperatures for perishable foods

Dispenser with Proximity Sensor - Designed to accommodate glassware of all sizes, from pitchers to tumblers; control graphics light up as you approach and automatically switch off when you walk away

Dairy Bin with Center Divider - Has a unique magnetic seal that locks in freshness

Filter-Change Indicator Light - Located on the upfront control panel, provides a visual reminder when it's time to replace the filter for the water dispenser

GE ® Water Filter - Has been moved from the fresh food compartment to the overhead cabinet, where it is discreetly out of sight

Drop-Down Shelf - Provides additional space for a casserole dish or pizza box

ZISB420DH

R


GE ZISB420DH Monogram® 42" Built-In Side-by-Side Refrigerator Quick Specs

FLUSH INSTALLATION

ZISB420DH

FLUSH INSTALLATION

ZISB420DH

ZISB480DX

Related manuals

Frequently Answers and Questions

What are the overall dimensions of GE ZISB420DH, including its 3/4" custom cabinet panel?

What is the required cutout size for GE ZISB420DH?

What power supply is required for GE ZISB420DH?

How much shipping weight does the GE ZISB420DH have?

What is the door swing capability of the GE ZISB420DH?

What is the maximum total weight allowed for custom panels on the GE ZISB420DH?

What are the dimensions of the dispenser cutout on the GE ZISB420DH?

GE ZISB420DH Monogram® 42" Built-In Side-by-Side Refrigerator Quick Specs

FLUSH INSTALLATION

ZISB420DH

FLUSH INSTALLATION

ZISB420DH

ZISB480DX

Related manuals

GE

ZISB480DK

GE

ZISB420DPII

Monogram

ZIS420NNII

Monogram

ZIS420NNII

GE

ZIS420NPII

GE

ZISB480DX

GE Monogram

ZISP480DHSS

GE

ZIS420NH

GE Monogram

ZISB360DK

GE Monogram

ZISB480DK

Frequently Answers and Questions

What are the overall dimensions of GE ZISB420DH, including its 3/4" custom cabinet panel?

What is the required cutout size for GE ZISB420DH?

What power supply is required for GE ZISB420DH?

How much shipping weight does the GE ZISB420DH have?

What is the door swing capability of the GE ZISB420DH?

What is the maximum total weight allowed for custom panels on the GE ZISB420DH?

What are the dimensions of the dispenser cutout on the GE ZISB420DH?