Bosch Recording Station Appliance

Bosch Recording Station Appliance
Bosch Recording Station Appliance
-
en
Quick Installation Guide
Bosch Recording Station Appliance
Table of Contents | en
3
Table of Contents
1
Safety Precautions
5
1.1
General Safety Precautions
5
1.2
Electrical Safety Precautions
1.3
Important Notices
10
1.4
FCC & ICES compliance
10
1.5
EMC Compliance
11
1.6
ESD Precautions
11
1.7
Operating Precautions
11
2
System Hardware Setup
12
2.1
Introduction
12
2.1.1
Scope of delivery
12
2.1.2
Connected Hardware
12
2.1.3
IP address
13
2.2
Unpacking
13
2.3
Preparing for Setup
13
2.3.1
Choosing a Setup Location
13
2.3.2
Rack Precautions (only for rackmount)
13
2.3.3
System Precautions
13
2.3.4
Rack Mounting Considerations (only BRS 19-inch models)
14
2.4
BRS 1U 19-inch Rackmount - Rack Mounting Instructions
15
9
2.4.1
Identifying the Sections of the Rack Rails
15
2.4.2
Inner Rails/Inner Rail Extensions
15
2.4.3
Outer Rails
16
2.4.4
Installing the Chassis into a Rack
17
2.4.5
Installing the Chassis into a Telco rack
18
2.5
BRS 2U 19-inch Rackmount - Rack Mounting Instructions
19
2.5.1
Separating the Sections of the Rack Rails
19
2.5.2
Inner Rails/Inner Rail Extensions
20
2.5.3
Outer Rails
20
2.5.4
Installing the Chassis into a Rack
21
3
System Software Setup
22
3.1
Starting the System for the first time
22
3.2
Configure Bosch Recording Station
23
3.3
Loading an existing configuration
24
4
Configuring Windows Firewall
25
5
Activating a License Package
26
6
Notes on Operation
27
6.1
Automatic Windows Updates
27
6.2
Hard Disks, Standby Mode, Screensaver
27
Bosch Security Systems
Quick Installation Guide
XMD-0071-VV002 | V3 | 2012.12
4
en | Table of Contents
Bosch Recording Station Appliance
7
Uninterruptible Power Supply
28
8
Recovery Procedure
29
XMD-0071-VV002 | V3 | 2012.12
Quick Installation Guide
Bosch Security Systems
Bosch Recording Station Appliance
Safety Precautions | en
1
Safety Precautions
1.1
General Safety Precautions
5
The following safety precautions must be observed:
Read, follow and retain instructions
All safety and operating instructions must be read and followed before installing the device.
Retain instructions for future reference.
Observe warnings
Observe all warnings on the device and in the Hardware Installation Manual.
Add-on devices
Do not use add-on devices that are not recommended by the product manufacturer as these
may cause hazards.
Installation notes
–
Do not place the device on an unstable mounting, tripod or similar. The device may fall to
the ground and seriously injure the user or be damaged itself.
–
Only use accessories that have been recommended by the manufacturer or are delivered
with the device.
–
–
Fit the device according to the manufacturer's instructions.
Exercise extreme caution when transporting the device on a trolley. Abrupt stopping,
extreme force effects and uneven surfaces may cause the device and the trolley to tip
over.
–
Keep the area around the system clean and free of clutter.
–
Place the chassis top cover and any system components that have been removed away
from the system or on a table so that they won't accidentally be stepped on.
–
While working on the system, do not wear loose clothing such as neckties and
unbuttoned shirt sleeves, which can come into contact with electrical circuits or be
pulled into a cooling fan.
–
Remove any jewelry or metal objects from your body, which are excellent metal
conductors that can create short circuits and harm you if they come into contact with
printed circuit boards or areas where power is present.
–
After accessing the inside of the system, close the system back up and secure it to the
rack unit after ensuring that all connections have been made.
–
The system is heavy when fully loaded. When lifting the system, two people at either end
should lift slowly with their feet spread out to distribute the weight. Always keep your
back straight and lift with your legs.
Cleaning
Unplug the device from the mains power supply before cleaning. Follow the instructions for
the device. Normally, cleaning can be carried out with a damp cloth. Do not use liquid
cleaners or cleaners in spray cans.
Service
Do not attempt to service the device yourself. You may be exposed to high electrical voltages
or other hazards if you open or remove covers. Servicing must be carried out by qualified
maintenance personnel.
Bosch Security Systems
Quick Installation Guide
XMD-0071-VV002 | V3 | 2012.12
6
en | Safety Precautions
Bosch Recording Station Appliance
Damage requiring service.
Unplug the device from the mains power supply and arrange for the device to be serviced by
qualified personnel if:
–
The mains cable or mains plug is damaged.
–
Liquids or foreign bodies are present in the device.
–
The device has come into contact with water and/or has been exposed to extreme
environmental conditions (e.g. rain, snow etc.).
–
If the device does not work properly in spite of following the operating instructions, make
changes only to those operating elements that are described in the operating
instructions. Incorrect changes to other operating elements may cause damage requiring
extensive repair work to be carried out by qualified service personnel.
–
The device has fallen to the ground or the housing has been damaged.
–
A noticeable change in the performance of the device has occurred. In this case, the
device must be serviced.
Spare parts
If spare parts are required, service personnel must use spare parts that are recommended by
the manufacturer or correspond to the original parts. Using the wrong spare parts may result
in fire, electric shock or other hazards.
Safety test
When servicing or repair is complete, ask service personnel to carry out a safety test to ensure
that the device is working correctly.
Power source
The device must only be operated with the power source indicated on the label. If you are not
sure whether you can operate the device with a specific power source, ask the dealer from
whom you bought the device or your electricity provider.
For devices that are operated using external power units, only recommended and tested
power units should be used.
For devices that are operated using power units with limited power, the power unit must
conform to the EN 60950 standard. Other replacement power units may damage the device
and lead to fire or electric shock.
Coax grounding
If a cable system is connected to the device for outside use, ensure that the cable system is
grounded. Only for models available in the USA: Section 810 of the National Electrical Code,
ANSI/ NFPA No.70-1981, contains information on the correct grounding of the mounting, coax
grounding at a discharge device, the size of the ground conductors, the location of the
discharge device, connection to discharge electrodes and requirements regarding the
discharge electrodes.
Grounding or polarizing
This device may have a polarized AC plug (a plug with one pin broader than the other). With
this protection system, the plug can only be inserted into a socket in one way. If you are
unable to insert the plug fully into the socket, rotate it and try again. If you are still unable to
insert the plug, ask an electrician to replace the socket with a later model. Do not attempt to
bypass the polarized plug.
Alternatively, the device may have a 3-phase ground plug with a third (grounding) pin. With
this protection system, the plug can only be inserted into a grounded socket. If you are unable
to insert the plug into the socket, ask an electrician to replace the socket with a later model.
Do not attempt to bypass the grounded plug.
XMD-0071-VV002 | V3 | 2012.12
Quick Installation Guide
Bosch Security Systems
Bosch Recording Station Appliance
Safety Precautions | en
7
Lightning
For added protection of the device during a storm, or when it is not used for a lengthy period
of time, unplug the device from the mains and disconnect the cable system. This prevents the
device being damaged by lightning or a power surge.
Location
The installation location should be quiet and have only limited access.
Devices for inside use
Water and damp — Do not use this device in the vicinity of water (e.g. in a damp cellar) or in
humid locations.
Entry of foreign bodies and liquids — Do not insert foreign bodies into the device openings
as you may touch parts that are at high-voltage or cause a short circuit, which may result in
fire or electric shock. Do not spill liquids on the device.
Mains cable and mains cable protectors — For devices that operate at 230 V AC, 50 Hz, the
input and output mains cables must conform to IEC publication 227 or IEC publication 245.
Mains cables should be laid in such a way that no one can step on them and no other objects
can be placed on top of them or leant against them. Particularly protect cables, plugs and
sockets as well as device entry points.
Overloading — Do not overload sockets and extension cables as this may result in fire or
electric shock.
Rack-mounting devices
Ventilation — This device should not be installed anywhere where correct ventilation cannot
be ensured or the manufacturer's instructions cannot be followed. The maximum operating
temperature for this device must not be exceeded.
Mechanical load — When installing the device in a rack, beware of hazards that may arise due
to unequal mechanical load.
WARNING!
Interruption of mains supply:
Voltage is applied as soon as the mains plug is inserted into the mains socket.
However, for devices with a mains switch, the device is only ready for operation when the
mains switch (ON/OFF) is in the ON position. When the mains plug is pulled out of the socket,
the supply of power to the device is completely interrupted.
WARNING!
Removing the housing:
To avoid electric shock, the housing must only be removed by qualified service personnel.
Before removing the housing, the plug must always be removed from the mains socket and
remain disconnected while the housing is removed. Servicing must only be carried out by
qualified service personnel. The user must not carry out any repairs.
WARNING!
Lithium battery:
Batteries that have been inserted wrongly can cause an explosion. Always replace empty
batteries with batteries of the same type or a similar type recommended by the manufacturer.
Dispose of empty batteries according to the manufacturer's instructions.
Bosch Security Systems
Quick Installation Guide
XMD-0071-VV002 | V3 | 2012.12
8
en | Safety Precautions
Bosch Recording Station Appliance
CAUTION!
Electrostatically sensitive device:
To avoid electrostatic discharges, the CMOS/MOSFET protection measures must be carried
out correctly.
When handling electrostatically sensitive printed circuits, grounded anti-static wrist bands
must be worn and the ESD safety precautions observed.
NOTICE!
Installation should only be carried out by qualified customer service personnel in accordance
with the applicable electrical regulations.
Disposal
Your Bosch product has been developed and manufactured using high-quality materials and
components that can be reused.
This symbol means that electronic and electrical devices that have reached the end of their
working life must be disposed of separately from household waste.
In the EU, separate collecting systems are already in place for used electrical and electronic
products. Please dispose of these devices at your local communal waste collection point or at
a recycling center.
XMD-0071-VV002 | V3 | 2012.12
Quick Installation Guide
Bosch Security Systems
Bosch Recording Station Appliance
1.2
Safety Precautions | en
9
Electrical Safety Precautions
Basic electrical safety precautions should be followed to protect you from harm and the
system from damage:
–
Be aware of the locations of the power on/off switch on the chassis as well as the room's
emergency power-off switch, disconnection switch or electrical outlet. If an electrical
accident occurs, you can then quickly remove power from the system.
–
Do not work alone when working with high voltage components.
–
Power should always be disconnected from the system when removing or in stalling main
system components, such as the mainboard, memory modules and floppy drive. When
disconnecting power, you should first power down the system with the operating system
first and then unplug the power cords of all the power supply units in the system.
–
When working around exposed electrical circuits, another person who is familiar with the
power-off controls should be nearby to switch off the power if necessary.
–
Use only one hand when working with powered-on electrical equipment. This is to avoid
making a complete circuit, which will cause electrical shock. Use extreme caution when
using metal tools, which can easily damage any electrical components or circuit boards
they come into contact with.
–
Do not use mats designed to decrease static electrical discharge as protection from
electrical shock. Instead, use rubber mats that have been specifically designed as
electrical insulators.
–
The power supply power cords must include a grounding plug and must be plugged into
grounded electrical outlets. The unit has more than one power supply cord. Disconnect
both power supply cords before servicing to avoid electrical shock.
–
Mainboard replaceable soldered-in fuses: Self-resetting PTC (Positive Temperature
Coefficient) fuses on the mainboard must be replaced by trained service technicians
only. The new fuse must be the same or equivalent as the one replaced. Contact
technical support for details and support.
CAUTION!
Mainboard Battery: There is a danger of explosion if the onboard battery is installed upside
down, which will reverse its polarities. This battery must be replaced only with the same or an
equivalent type recommended by the manufacturer (CR2032). Dispose of used batteries
according to the manufacturer's instructions.
CAUTION!
DVD-ROM Laser: Some systems come with a DVD-ROM drive. To prevent direct exposure to
the laser beam and hazardous radiation exposure, do not open the enclosure or use the unit in
any unconventional way.
CAUTION!
Class I Laser Product
Invisible laser radiation when open. Avoid exposure to beam.
Bosch Security Systems
Quick Installation Guide
XMD-0071-VV002 | V3 | 2012.12
10
1.3
en | Safety Precautions
Bosch Recording Station Appliance
Important Notices
Accessories - Do not place this unit on an unstable stand, tripod, bracket, or mount. The unit
may fall, causing serious injury and/or serious damage to the unit. Use only with the cart,
stand, tripod, bracket, or table specified by the manufacturer. When a cart is used, use
caution and care when moving the cart/apparatus combination to avoid injury from tip-over.
Quick stops, excessive force, or uneven surfaces may cause the cart/unit combination to
overturn. Mount the unit per the manufacturer's instructions.
1.4
FCC & ICES compliance
FCC & ICES Information
(U.S.A. and Canadian Models Only)
This device complies with part 15 of the FCC Rules. Operation is subject to the following
conditions:
–
–
this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules and ICES-003 of Industry Canada. These
limits are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and
radiates radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his expense.
Intentional or unintentional modifications, not expressly approved by the party responsible
for compliance, shall not be made. Any such modifications could void the user's authority to
operate the equipment. If necessary, the user should consult the dealer or an experienced
radio/television technician for corrective action.
The user may find the following booklet, prepared by the Federal Communications
Commission, helpful: How to Identify and Resolve Radio-TV Interference Problems. This booklet
is available from the U.S. Government Printing Office, Washington, DC 20402, Stock No. 004000-00345-4.
Informations FCC et ICES
(modèles utilisés aux États-Unis et au Canada uniquement)
Ce produit est conforme aux normes FCC partie 15. la mise en service est soumises aux deux
conditions suivantes :
–
–
cet appareil ne peut pas provoquer d'interférence nuisible et
cet appareil doit pouvoir tolérer toutes les interférences auxquelles il est soumit, y
compris les interférences qui pourraient influer sur son bon fonctionnement.
AVERTISSEMENT: Suite à différents tests, cet appareil s’est révélé conforme aux exigences
imposées aux appareils numériques de Classe A en vertu de la section 15 du règlement de la
Commission fédérale des communications des États-Unis (FCC). Ces contraintes sont destinées
à fournir une protection raisonnable contre les interférences nuisibles quand l'appareil est
utilisé dans une installation commerciale. Cette appareil génère, utilise et émet de l'energie
de fréquence radio, et peut, en cas d'installation ou d'utilisation non conforme aux
instructions, générer des interférences nuisibles aux communications radio. L’utilisation de ce
produit dans une zone résidentielle peut provoquer des interférences nuisibles. Le cas
échéant, l’utilisateur devra remédier à ces interférences à ses propres frais.
XMD-0071-VV002 | V3 | 2012.12
Quick Installation Guide
Bosch Security Systems
Bosch Recording Station Appliance
Safety Precautions | en
11
Au besoin, l’utilisateur consultera son revendeur ou un technicien qualifié en radio/télévision,
qui procédera à une opération corrective. La brochure suivante, publiée par la Commission
fédérale des communications (FCC), peut s’avérer utile : How to Identify and Resolve Radio-TV
Interference Problems (Comment identifier et résoudre les problèmes d’interférences de radio
et de télévision). Cette brochure est disponible auprès du U.S. Government Printing Office,
Washington, DC 20402, États-Unis, sous la référence n° 004-000-00345-4.
1.5
EMC Compliance
NOTICE!
This is a class A product. In a domestic environment this product may cause radio
interference, in which case the user may be required to take adequate measures.
1.6
ESD Precautions
Electrostatic Discharge (ESD) is generated by two objects with different electrical charges
coming into contact with each other. An electrical discharge is created to neutralize this
difference, which can damage electronic components and printed circuit boards. The
following measures are generally sufficient to neutralize this difference before contact is
made to protect your equipment from ESD:
–
Use a grounded wrist strap designed to prevent static discharge.
–
Keep all components and printed circuit boards (PCBs) in their antistatic bags until ready
–
Touch a grounded metal object before removing the board from the antistatic bag.
–
Do not let components or printed circuit boards come into contact with your clothing,
for use.
which may retain a charge even if you are wearing a wrist strap.
–
Handle a board by its edges only. Do not touch its components, peripheral chips, memory
–
When handling chips or modules, avoid touching their pins.
modules or contacts.
–
Put the mainboard and peripherals back into their antistatic bags when not in use.
–
For grounding purposes, make sure your computer chassis provides excellent
conductivity between the power supply, the case, the mounting fasteners and the
mainboard.
1.7
Operating Precautions
The chassis cover must be in place when the system is operating to assure proper cooling.
Out of warranty damage to the system can occur if this practice is not strictly followed.
Bosch Security Systems
Quick Installation Guide
XMD-0071-VV002 | V3 | 2012.12
12
en | System Hardware Setup
Bosch Recording Station Appliance
2
System Hardware Setup
2.1
Introduction
This Quick Installation Guide covers the initial installation, the creation of a configuration and
the process for loading an existing configuration.
This Quick Installation Guide applies to the following models:
–
Bosch Recording Station Tower (BRS Tower)
–
Bosch Recording Station 1U 19-inch Rackmount (BRS 1U 19-inch Rackmount)
–
Bosch Recording Station 2U 19-inch Rackmount (BRS 2U 19-inch Rackmount)
For further information on configuration, refer to the Hardware Installation Manual.
Information regarding the operation of the Bosch Recording Station can be found in the
operating manual.
Note:
The monitor VGA output of the BRS Appliance 19-inch models is only for configuration and
maintenance purposes.
2.1.1
Scope of delivery
BRS Tower
–
Bosch Recording Station software is pre-installed with an 8 IP license.
–
MiniTower system, fully equipped with one or four hard drives
–
In addition to the system itself, the following items should have been shipped along with
each system
–
AC power cables (region dependant)
–
One CD with manuals
–
This Quick Installation Guide
BRS 1U 19-inch Rackmount / BRS 2U 19-inch Rackmount
–
–
Bosch Recording Station software is pre-installed with an 8 IP license.
Fully equipped with 4 hard drives (BRS 1U 19-inch Rackmount) or 8 hard drives (BRS 2U
19-inch Rackmount).
–
In addition to the system itself, the following items should have been shipped along with
each system
2.1.2
–
One rack mount kit
–
AC power cables for each power supply (region dependant)
–
One CD with manuals
–
This Quick Installation Guide
Connected Hardware
The following components can be connected to the system.
–
IP cameras and IP AutoDomes (for compatible codecs, refer to datasheet for the Bosch
Recording Station)
–
Encoders with analog cameras (for compatible codecs, refer to datasheet for the Bosch
Recording Station)
–
ATM/POS (automatic teller machines/cashpoint systems)
–
Bosch alarm panels
–
Communication devices
–
SMTP e-mail server and SMS service
–
RAID subsystems for enhanced memory capacity
–
Remote stations (Bosch Recording Station or DiBos recorder/DiBos IP recorder)
XMD-0071-VV002 | V3 | 2012.12
Quick Installation Guide
Bosch Security Systems
Bosch Recording Station Appliance
2.1.3
System Hardware Setup | en
13
IP address
We recommend that all IP cameras and encoders be assigned fixed IP addresses. Do not use
DHCP.
2.2
Unpacking
Inspect the box the system was shipped in and note if it was damaged in any way. If the
system itself shows damage you should file a damage claim with the carrier who delivered it
and notify the respective Bosch RMA desk.
Due to the weight of the disk array: After opening the top of the shipping box, one person
should stand at either end and lift the disk array out together.
2.3
Preparing for Setup
Follow the steps in the order given to complete the installation process in a minimum amount
of time. Read this section before you begin the installation procedure outlined in the sections
that follow.
2.3.1
Choosing a Setup Location
This product is for installation only in a restricted access location (dedicated equipment
rooms, service closets and the like).
The system should be situated in a clean, dust-free area that is well ventilated. Avoid areas
where heat, electrical noise and electromagnetic fields are generated. You will also need it
placed near a grounded power outlet.
BRS Tower
Leave enough clearance in front and side where the chassis cover is located of the system to
be able to remove swappable drives and to allow for sufficient airflow and ease in servicing.
BRS 1U 19-inch Rackmount / BRS 2U 19-inch Rackmount
Leave enough clearance in front of the rack to be able to open the front door completely
(approximately 25 inches) and approximately 30 inches of clearance in the back of the rack to
allow for sufficient airflow and ease in servicing.
2.3.2
Rack Precautions (only for rackmount)
–
Ensure that the leveling jacks on the bottom of the rack are fully extended to the floor
with the full weight of the rack resting on them.
–
In single rack installation, stabilizers should be attached to the rack. In multiple rack
–
Always make sure the rack is stable before extending a component from the rack.
–
You should extend only one component at a time - extending two or more simultaneously
installations, the racks should be coupled together.
may cause the rack to become unstable.
2.3.3
System Precautions
–
Review the electrical and general safety precautions.
–
Use a regulating uninterruptible power supply (UPS) to protect the system from power
surges, voltage spikes if you want to keep your system operating in case of a power
failure
–
–
Allow the SATA drives and power supply modules to cool before touching them.
Always keep the chassis covers in place and secured when not servicing to maintain
proper cooling.
–
Determine the placement of each component in the rack before you install the rails (only
BRS 19-inch models).
Bosch Security Systems
Quick Installation Guide
XMD-0071-VV002 | V3 | 2012.12
14
en | System Hardware Setup
–
Bosch Recording Station Appliance
Install the heaviest system components on the bottom of the rack first, and then work up
(only BRS 19-inch models).
–
Always keep the rack's front door and all panels and components on the systems closed
when not servicing to maintain proper cooling (only BRS 19-inch models).
2.3.4
Rack Mounting Considerations (only BRS 19-inch models)
Ambient Operating Temperature
If installed in a closed or multi-unit rack assembly, the ambient operating temperature of the
rack environment may be greater than the ambient temperature of the room. Therefore,
consideration should be given to installing the equipment in an environment compatible with
the manufacturer’s maximum rated ambient temperature (Tmra).
Reduced Airflow
Equipment should be mounted into a rack so that the amount of airflow required for safe
operation is not compromised.
Mechanical Loading
Equipment should be mounted into a rack so that a hazardous condition does not arise due to
uneven mechanical loading.
Circuit Overloading
Consideration should be given to the connection of the equipment to the power supply
circuitry and the effect that any possible overloading of circuits might have on over current
protection and power supply wiring. Appropriate consideration of equipment product label
ratings should be used when addressing this concern.
Reliable Ground
A reliable ground must be maintained at all times. To ensure this, the rack itself should be
grounded. Particular attention should be given to power supply connections other than the
direct connections to the branch circuit (i.e. the use of power strips, etc.).
XMD-0071-VV002 | V3 | 2012.12
Quick Installation Guide
Bosch Security Systems
Bosch Recording Station Appliance
2.4
System Hardware Setup | en
15
BRS 1U 19-inch Rackmount - Rack Mounting Instructions
This section provides information on installing the chassis into a rack unit. There are a variety
of rack units on the market, which may mean the assembly procedure will differ slightly. You
should also refer to the installation instructions that came with the rack unit you are using.
Note:
This rail will fit a rack between 26" and 33.5" deep.
2.4.1
Identifying the Sections of the Rack Rails
The chassis package includes two rack rail assemblies in the rack mounting kit.
Each assembly consists of two sections:
2.4.2
–
an inner fixed chassis rail that secures directly to the system chassis
–
an outer fixed rack rail that secures directly to the rack itself.
1
Rail Extension (Inner Rail is pre-installed on the chassis)
2
Outer Rails
Inner Rails/Inner Rail Extensions
The chassis includes a set of inner rails which are in two sections:
–
inner rails
–
inner rail extensions.
The inner rails are pre-attached and do not interfere with normal use of the chassis if you
decide not to use a server rack. Attach the inner rail extension to stabilize the chassis within
the rack.
Bosch Security Systems
Quick Installation Guide
XMD-0071-VV002 | V3 | 2012.12
16
en | System Hardware Setup
Bosch Recording Station Appliance
Installing the Inner Rails
1.
Place the inner rail extensions on the side of the chassis aligning the hooks of the chassis
with the inner rail extension holes. Make sure the inner rail extension faces "outward"
just like the pre-attached inner rail.
2.4.3
2.
Slide the extension toward the front of the chassis.
3.
Secure the chassis with 2 screws as illustrated.
4.
Repeat steps 1-3 for the other inner rail extension.
Outer Rails
Assembling the Outer Rails
1
Secure to the front of the rack.
2
Attach the two sections of the outer rail together.
3
Secure to the rear of the rack.
XMD-0071-VV002 | V3 | 2012.12
Quick Installation Guide
Bosch Security Systems
Bosch Recording Station Appliance
System Hardware Setup | en
17
Installing the Outer Rails to the Rack
1.
Attach the longer section of the outer rail to the outside of the shorter section of the
outer rail. You must align the pins with the slides. Both ends of the outer rail must face
the same direction in order to be secured to the rack (see also Section Assembling the
Outer Rails, page 16).
2.
Adjust both sections of the outer rail to the proper length so that the rail fits snugly
within the rack.
3.
Secure the longer section of the outer rail to the front of the rack with two M5 screws
and the shorter section to the rear side of the rack with two M5 screws.
4.
Repeat steps 1-4 for the remaining outer rail.
Locking Tabs
–
Both chassis rails have a locking tab, which serves two functions. The first is to lock the
system into place when installed and pushed fully into the rack, which is its normal
position. Secondly, these tabs also lock the system in place when fully extended from the
rack. This prevents the system from coming completely out of the rack when you pull it
out for servicing.
2.4.4
Bosch Security Systems
Installing the Chassis into a Rack
Quick Installation Guide
XMD-0071-VV002 | V3 | 2012.12
18
en | System Hardware Setup
1.
Bosch Recording Station Appliance
Confirm that chassis includes the inner rails (A) and rail extensions (B). Also, confirm
that the outer rails (C) are installed on the rack.
2.
Line chassis rails (A and B) with the front of the rack rails (C).
3.
Slide the chassis rails into the rack rails, keeping the pressure even on both sides (you
may have to depress the locking tabs when inserting). When the server has been pushed
completely into the rack, you should hear the locking tabs "click" into the locked position.
4.
(Optional) Insert and tighten the thumbscrews that hold the front of the server to the
rack.
2.4.5
Installing the Chassis into a Telco rack
To install the chassis into a Telco type rack, use two L-shaped brackets on either side of the
chassis (four total). First, determine how far follow the server will extend out the front of the
rack. Larger chassis should be positioned to balance the weight between front and back. If a
bezel is included on your server, remove it. Then attach the two front brackets to each side of
the chassis, then the two rear brackets positioned with just enough space to accommodate
the width of the telco rack. Finish by sliding the chassis into the rack and tightening the
brackets to the rack.
XMD-0071-VV002 | V3 | 2012.12
Quick Installation Guide
Bosch Security Systems
Bosch Recording Station Appliance
2.5
System Hardware Setup | en
19
BRS 2U 19-inch Rackmount - Rack Mounting Instructions
This section provides information on installing the chassis into a rack unit with the quickrelease rails provided. There are a variety of rack units on the market, which may mean the
assembly procedure will differ slightly. You should also refer to the installation instructions
that came with the rack unit you are using.
NOTE: This rail will fit a rack between 26" and 33.5" deep.
2.5.1
Separating the Sections of the Rack Rails
The chassis package includes two rail assemblies in the rack mounting kit. Each assembly
consists of two sections: an inner fixed chassis rail that secures directly to the server chassis
and an outer fixed rack rail that secures directly to the rack itself.
Bosch Security Systems
1.
Locate the rail assembly in the chassis packaging.
2.
Extend the rail assembly by pulling it outward.
3.
Press the quick-release tab.
4.
Separate the inner rail extension from the outer rail assembly.
Quick Installation Guide
XMD-0071-VV002 | V3 | 2012.12
20
en | System Hardware Setup
2.5.2
Bosch Recording Station Appliance
Inner Rails/Inner Rail Extensions
The chassis includes a set of inner rails in two sections:
–
inner rails
–
inner rail extensions.
The inner rails are pre-attached to the chassis, and do not interfere with normal use of the
chassis if you decide not to use a server rack. The inner rail extension is attached to the inner
rail to mount the chassis in the rack.
Installing the Inner Rails
1.
Place the inner rail extensions on the side of the chassis aligning the hooks of the chassis
with the rail extension holes. Make sure the extension faces "outward" just like the preattached inner rail.
2.
3.
Slide the extension toward the front of the chassis.
Secure the chassis with 2 screws as illustrated. Repeat steps for the other inner rail
extension.
2.5.3
Outer Rails
Outer rails attach to the rack and hold the chassis in place. The outer rails for the chassis
extend between 30 inches and 33 inches.
Installing the Outer Rails to the Rack
1.
Secure the back end of the outer rail to the rack, using the screws provided.
2.
Press the button where the two outer rails are joined to retract the smaller outer rail.
3.
Hang the hooks of the rails onto the rack holes and if desired, use screws to secure the
front of the outer rail onto the rack.
4.
Repeat steps 1-3 for the remaining outer rail.
XMD-0071-VV002 | V3 | 2012.12
Quick Installation Guide
Bosch Security Systems
Bosch Recording Station Appliance
2.5.4
System Hardware Setup | en
21
Installing the Chassis into a Rack
1.
Extend the outer rails as illustrated above.
2.
Align the inner rails of the chassis with the outer rails on the rack.
3.
Slide the inner rails into the outer rails, keeping the pressure even on both sides. When
the chassis has been pushed completely into the rack, it should click into the locked
position.
4.
Bosch Security Systems
Optional screws may be used to secure the to hold the front of the chassis to the rack.
Quick Installation Guide
XMD-0071-VV002 | V3 | 2012.12
22
en | System Software Setup
Bosch Recording Station Appliance
3
System Software Setup
3.1
Starting the System for the first time
To start the system for the first time, proceed with the following steps.
1.
Plug the power cords from the power supply unit into a high-quality power strip that
offers protection from electrical noise and power surges.
2.
Press the power button on the front panel to start the system. The system starts the
initialization. This can take a few minutes, and the system may restart. After the
initialization the Set Up Windows screen is displayed where you can select the language
3.
Select the system language, then click Next >.
4.
Select your regional settings, then click Next >.
5.
Accept the license terms, then click Next >.
6.
Select the time zone and the date and time, then click Next >.
Note: If you have changed the language, the system restarts.
The system logs on automatically in administrator mode. The Windows desktop is
displayed.
7.
The message Windows will shut down in less than a minute is displayed.
The system restarts. The Windows logon screen is displayed.
8.
9.
Enter Administrator and the password 1357, then press ENTER.
You can now configure the network, computer name, IP cameras and the Bosch
Recording Station or you can load an existing Bosch Recording Station configuration file.
Note:
To load an existing Bosch Recording Station configuration file, click Start, right-click
Bosch Recording Station, then click Run as administrator.
–
To configure the Recording Station:
See Quick Installation Guide
–
To load an existing configuration:
See Quick Installation Guide
10. Click Start, then click Restart.
The system starts in BRSuser mode and displays the following:
–
You have not configured the system: The Configuration Wizard is displayed.
–
You have configured the system: Bosch Recording Station starts automatically. Enter
the relevant user name and password. The user interface is displayed.
11. The keyboard setting for the BRSuser remains in default English (US) if you have changed
the languge.
To change the keyboard setting, proceed with the following steps:
–
In the taskbar, right-click the keyboard icon, then click Settings....
–
In the Text Services and Input Languages dialog box, click Add.
–
In the Add Input Language dialog box, select your keyboard language, then click OK.
–
In the Installed services list remove all languages not needed.
To proceed this, select the keyboard in the Installed services list, then click
Remove.
–
Click OK.
NOTICE!
To prevent unauthorized access to the system, do not configure an Account Picture for the
BRSuser.
XMD-0071-VV002 | V3 | 2012.12
Quick Installation Guide
Bosch Security Systems
Bosch Recording Station Appliance
3.2
System Software Setup | en
23
Configure Bosch Recording Station
To perform a basic configuration, proceed as follows:
1.
Click Start, then click Bosch Recording Station. The configuration wizard is displayed.
2.
In the Bosch Recording Station – Configuration Wizard dialog box, click Next >.
3.
In the License activation dialog box, click Recorder.
Following licenses are activated by default:
4.
–
Number of network cameras: 8
–
Number of remote stations: 32
–
CD/DVD writing
Select the desired license package from the License: list and click Activate.... The
Activate license dialog box is displayed.
Note:
If you need more packages, you can activate them in this dialog box.
5.
Enter the activation key in the License activation key: box and click Activate.
Note:
If you do not yet have an activation key, refer to Section 5 Activating a License Package.
6.
Click Next >.
7.
In the Remote stations dialog box, click New if you want to add remote stations.
8.
Create a new user in the Users dialog box by entering a name and password in the
relevant authorization. Make a note of the name and password, because you will need
these details afterwards to log on.
Note:
–
During the first configuration, 3 authorization levels and 3 users are automatically
created. These authorizations cannot be deleted.
9.
Click Next > .
10. In the Schedules dialog box, a suggested weekly overview appears with 3 time profiles in
different colors (Day, Night, Weekend).
If you want to amend the weekly overview, click a time profile to select it.
Then, in the weekly overview, click the time that you want to assign to the time profile.
Dragging up a square while pressing the left mouse button marks a time profile. All
selected times take the color of the selected time profile.
11. Click Next >.
12. The Add IP cameras dialog box provides an overview of all MPEG4/H.264 IP cameras in
the system.
13. Check the cameras to be added to the Bosch Recording Station.
Note:
To perform another network search, click Rescan.
14.
Click Next >.
15. In the Camera settings dialog box, select a camera and enter a name for it in the Name
(in Bosch Recording Station): box. This name is displayed as the camera name in the
Bosch Recording Station.
16. Enter the relevant user name and password for MPEG4/H.264 devices, where required
for login purposes (e.g. when a user name and password are configured in the MPEG4/
H.264 device).
17. Select the stream of the MPEG4/H.264 device (Stream 1 or Stream 2) to be used for
viewing live images.
Note:
Some IP cameras only support one stream.
Bosch Security Systems
Quick Installation Guide
XMD-0071-VV002 | V3 | 2012.12
24
en | System Software Setup
Bosch Recording Station Appliance
18. Activate the Motion detection option and/or Reference image check option of the
MPEG4/H.264 device.
Note:
–
Some IP cameras do not support motion detection or reference image checking.
–
The motion detection and reference image check must also be activated in the
MPEG4/H.264 device.
19. Repeat these processes for each camera. It is possible to select multiple cameras.
20. Arrange the cameras in the order in which they are to appear in the Bosch Recording
Station. Use the arrows on the right-hand side of the dialog box to do so.
21. Click Next >.
22. Select a camera in the Recording settings dialog box and enter the settings for a
continuous recording under Continuous recording of selected camera(s).
23. Repeat this process for each camera. It is possible to select multiple cameras.
24. Click Finish to complete the configuration.
25. Bosch Recording Station starts automatically. Enter the relevant user name and
password. The user interface is displayed.
Refer to the following documentation/help for information regarding configuration of the
Bosch Recording Station:
–
–
For operating instructions: see the Bosch Recording Station Operating Manual
For additional configuration information, see Bosch Recording Station Installation
Manual
3.3
Loading an existing configuration
Note:
If you want to load an existing Bosch Recording Station configuration file, you must log on the
BRS Appliance in administrator mode.
To install an existing configuration, proceed as follows:
1.
Click Start, right-click Bosch Recording Station, then click Run as administrator. The
configuration wizard is displayed.
2.
In the Bosch Recording Station – Configuration Wizard dialog box, click Load... to load
an existing configuration file (.prm file).
Note:
It is not possible to load DiBos configurations.
3.
Confirm the warning dialog by clicking Yes.
4.
Select the relevant configuration file and click Open. The system loads the configuration.
5.
Bosch Recording Station starts automatically. Enter the relevant user name and
password. The user interface is displayed.
Note:
We recommend starting Bosch Recording Station in BRSuser mode.
XMD-0071-VV002 | V3 | 2012.12
Quick Installation Guide
Bosch Security Systems
Bosch Recording Station Appliance
4
Configuring Windows Firewall | en
25
Configuring Windows Firewall
General:
The Windows Firewall is deactivated by default. If you need to activate the Windows firewall,
the following exceptions must be added and selected in the Windows firewall.
Bosch Recording Station
Exceptions in Windows firewall settings
ConnectionServer.exe
DBServer.exe
DiBosExplorer.exe
DomeCameraUnit.exe
DVRServiceShimWrapper.exe
JobServer.exe
Parametrierung.exe
VCSModule.exe
VSDKPluginModule.exe
DCOM (TCP) Port 135
DCOM (UDP) Port 135
Remote Configuration (TCP) Port 8080
Bosch Security Systems
Quick Installation Guide
XMD-0071-VV002 | V3 | 2012.12
26
5
en | Activating a License Package
Bosch Recording Station Appliance
Activating a License Package
To activate a license, you require a license activation key. The license activation key can be
obtained via the Bosch License Manager.
To obtain a license activation key, proceed as follows:
1.
Look up the authorization number of the license package to be activated by referring to
the authorization letter or e-license for the relevant license package.
2.
Start the Bosch Recording Station configuration.
3.
Select the Software licenses menu.
4.
Select the desired license package from the License: list and click Activate.... The
Activate license dialog box is displayed.
5.
Make a note of the computer signature or use the copy and paste function to insert it into
a text file. You can find the computer signature in the 3) Computer signature: box.
6.
On a computer with Internet access, enter the following URL in the browser:
https://activation.boschsecurity.com
You are now in Bosch License Manager.
Follow the instructions to call up a license activation key.
7.
Make a note of the license activation key or use the copy and paste function to it into a
text file. There is a field for the license activation key in the authorization letter, under the
sticker with the authorization number. This also applies to the computer signature of the
affected computer. Enter the license activation key and the computer signature in the
authorization letter.
8.
In the Activate license dialog box in the Bosch Recording Station configuration, enter the
license activation key obtained from the Bosch License Manager and click Activate. The
license package is activated.
XMD-0071-VV002 | V3 | 2012.12
Quick Installation Guide
Bosch Security Systems
Bosch Recording Station Appliance
Notes on Operation | en
6
Notes on Operation
6.1
Automatic Windows Updates
27
The automatic installation of Windows updates is deactivated by default to prevent the
computer from automatically installing a Windows update from the Internet and then
subsequently restarting.
If you have changed this setting, make sure that you are able to choose whether you want to
install the update or not.
NOTICE!
Restarting the computer following an automatic Windows update will interrupt recording.
Recommended settings if automatic updates for Windows 7 are required:
1.
Click Start, select Control Panel and double-click System and Security.
2.
Click Windows Update and then select the Change settings option on the left.
3.
Under Important updates, select the option Download updates but let me choose
whether to install them.
Note:
If the computer is not connected to the Internet, we recommend that you select Never
check for updates (not recommended).
4.
6.2
Click OK.
Hard Disks, Standby Mode, Screensaver
Hard Disks, Standby Mode
By default, the hard disks are activated and the computer does not switch to standby mode.
Deactivating the hard disks or switching the computer to standby mode may result in the
recording being interrupted or terminated.
Screensaver
By default no screensaver is installed. An installed screensaver can lead to problems with
displaying images. The appearance of the screensaver creates entries in the log file.
Bosch Security Systems
Quick Installation Guide
XMD-0071-VV002 | V3 | 2012.12
28
7
en | Uninterruptible Power Supply
Bosch Recording Station Appliance
Uninterruptible Power Supply
Observe the following:
–
Loss of power can cause corruption of the Operating System or the stored video. To
avoid loss of data and ensure trouble-free operation, we recommend installing an UPS for
critical applications.
–
To comply with EN50130-4 voltage interruption (§ 8.3.4) an external UPS is required.
–
To connect and configure the UPS, observe the manufacturer's documentation delivered
with the UPS.
Note:
The UPS is not contained in the product.
XMD-0071-VV002 | V3 | 2012.12
Quick Installation Guide
Bosch Security Systems
Bosch Recording Station Appliance
8
Recovery Procedure | en
29
Recovery Procedure
If system fails to start, recover the system as described in the Recovery Procedure for BRS
Appliance manual.
Bosch Security Systems
Quick Installation Guide
XMD-0071-VV002 | V3 | 2012.12
30
en | Recovery Procedure
XMD-0071-VV002 | V3 | 2012.12
Bosch Recording Station Appliance
Quick Installation Guide
Bosch Security Systems
Bosch Security Systems
Robert-Bosch-Ring 5
85630 Grasbrunn
Germany
www.boschsecurity.com
© Bosch Security Systems, 2012
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement