PT-F300[E]
S
P
E
P ro d u c t N u m b e r :
PT-F300
P ro d u c t N a m e :
LCD Projector
C
F
I
L
E
As of May 2009. Appearance and specifications are subject to change without notice.
< 1 >
S
P
E
C
F
I
L
E
PT-F300
LCD Projector
Specifications
Power supply
Power consumption
Optical system
LCD panel
Panel size
Display method
Drive method
Pixels
Pixel configuration
Lens
Lamp
Colors
Brightness * 1
Center-to-corner uniformity * 1
Contrast ratio* 1
Resolution
RGB
Scanning frequency
RGB
YPBPR
S-Video/Video
Projection size
Throw distance
Optical axis shift
Keystone correction range
Installation
On-screen menu
Built-in speakers
Terminals
Size
Output power
DVI-D IN
COMPUTER (RGB) 1
R, G, B:
Y, PB, PR:
COMPUTER (RGB) 2
R, G, B:
Y, PB, PR:
As of May 2009
100–240 V AC, 50/60 Hz
350 W (Approx. 4 W in standby mode with fan stopped. Approx. 25 W
when standby mode is turned on by a Web browser, and approx. 35 W
when audio is output during standby mode.)
Dichroic mirror separation/prism synthesis system
0.8˝ (20.32 mm) diagonal, 4:3 aspect ratio
Transparent LCD panel (x 3, R/G/B)
Active matrix
786,432 (1,024 x 768) x 3, total of 2,359,296 pixels
Stripe
Manual zoom (1:1–1:2), manual focus
F 1.7– 2.6, f 24.0 – 47.2 mm
250 W UHM lamp
Full color (16,777,216 colors)
4,000 lumens
80%
600:1 (full on/full off)
1,024 x 768 pixels (Input signals that exceed this resolution will be
converted to 1,024 x 768 pixels.)
Horizontal: 15 .00 – 91.00 kHz, Vertical: 50– 85 Hz
480i (525i): fH 15.75 kHz; fV 60 Hz
576i (625i): fH 15.63 kHz; fV 50 Hz
480p (525p): fH 31.50 kHz; fV 60 Hz
576p (625p): fH 31.25 kHz; fV 50 Hz
720 (750)/60p: fH 45.00 kHz; fV 60 Hz
720 (750)/50p: fH 37.50 kHz; fV 50 Hz
1080 (1125)/60: fH 33.75 kHz; fV 60 Hz
1080 (1125)/50i: fH 28.13 kHz; fV 50 Hz
1080 (1125)/60p: fH 67.50 kHz; fV 60 Hz
1080 (1125)/50p: fH 56.30 kHz; fV 50 Hz
NTSC, NTSC4.43, PAL-M, PAL60: fH 15.75 kHz; fV 60 Hz
PAL, SECAM, PAL-N: fH 15.63 kHz; fV 50 Hz
838 –7,620 mm (33 – 300 inches) diagonally, 16:10 aspect ratio
1.2 m – 18.1 m (3´11˝ 59´5˝), 4:3 aspect ratio
Vertical: ±50%, horizontal: ±27%
Vertical: approx. ±30°
Front/rear, ceiling/desk (menu selection)
17 languages: English, French, German, Spanish, Italian, Korean,
Russian, Chinese, Japanese, Swedish, Norwegian, Danish, Portuguese,
Polish, Hungarian, Czech, and Thai
4 cm (round), x 1
5.0 W (monaural)
DVI-D 24-pin x 1, DVI 1.0 compliant, HDCP compatible, for single link
only
EDID1: 480p, 576p, 720/60p, 720/50p, 1080/60i, 1080/50i, 1080/60p,
1080/50p
EDID2: Compatible with non-interlaced signals only,
Effective resolution: VGA (640 x 480) – SXGA+ (1,400 x 1,050)
IN D-sub HD 15-pin (female) x 1
G: 0.7 Vp-p, 75 ohms, Sync on green: 1.0 Vp-p, 75 ohms,
B, R: 0.7 Vp-p, 75 ohms,
HD/SYNC, VD: TTL (positive/negative polarity compatible)
Y: 1.0 Vp-p (including sync signal), 75 ohms,
PB, PR: 0.7 Vp-p, 75 ohms
IN/COMPUTER 1 OUT
D-sub HD 15-pin x 1 (female)
(Input/output is selected from the menu. When output is selected,
the COMPUTER (RGB) 1 IN signal is output.)
G: 0.7 Vp-p, 75 ohms, Sync on green: 1.0 Vp-p, 75 ohms,
B, R: 0.7 Vp-p, 75 ohms,
HD/SYNC, VD: TTL (positive/negative polarity compatible)
Y: 1.0 Vp-p (including sync signal), 75 ohms,
PB, PR: 0.7 Vp-p, 75 ohms
< 2 >
S
P
E
F
C
I
L
E
PT-F300
LCD Projector
Power cord length
Cabinet material
Dimensions (W x H x D)
Weight * 2
Operating environment
Remote control unit
RCA pin x 1, 1.0 Vp-p, 75 ohms
VIDEO IN
Mini DIN 4-pin x 1, Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms
S-VIDEO IN
COMPUTER AUDIO IN 1 M3 (stereo) x 1, 0.5 Vrms, for COMPUTER 1
COMPUTER AUDIO IN 2 M3 (stereo) x 1, 0.5 Vrms, for DVI-D and COMPUTER 2
RCA (L, R) x 1, 0.5 V [rms], for VIDEO and S-VIDEO (default)
AUDIO IN
(This can be switched by a setting for use as an audio input terminal for DVI-D/COMPUTER 1/COMPUTER 2.)
M3 (stereo) x 1, 0 – 2.0 Vrms (variable)
VARIABLE AUDIO OUT
D-sub 9-pin x 1, for external control (RS-232C)
SERIAL
D-sub 9-pin x 1, for external control (contact control)
REMOTE
RJ-45 x 1, compatible with PJLink™ (class 1), 10BASE-T/100BASE-TX
LAN
2 m/6´7˝
Moulded plastic (PC+ABS)
432 x 128.5 x 323 mm (17˝ x 5-1/16˝ x 12-23/32˝)
Approx. 6.2 kg (13.7 lbs.)
0°– 40°C (32°–104°F)
Temperature
20%– 80% (no condensation)
Humidity
3 V DC (AA battery x 2)
Power supply
Approx. 15 m (49´3˝) when operated from directly in front of the
Operation range * 3
signal receptor
Dimensions (W x H x D) 48 x 163 x 24.5 mm (1-7/8˝ x 6-13/32˝ x 31/32˝)
117 g (4.1 oz) (including batteries)
Weight
Wireless Manager ME 5.5 system requirements
OS
To use network functions, a PC is required that meets the conditions
given below.
Microsoft® Windows® 2000 Professional SP4, Windows® XP
Professional, Windows® XP Home Edition, Windows® XP Tablet PC
Edition 2005, Windows Vista® Ultimate 32-bit, Windows Vista®
Business 32-bit, Windows Vista® Home Premium 32-bit, Windows
Vista® Home Basic 32-bit
Apple Mac OS X 10.4 (Tiger) and OS X 10.5 (Leopard)
NOTE: Some functions are not available with Windows Vista ® and Mac.
Web browser
CPU
Memory
Free hard disk space
CD-ROM drive
Wired LAN connector
Supplied accessories
Optional accessories
*1
*2
*3
Windows®: Internet Explorer 6.0 or later, or Netscape Communicator
7.0 or later
Macintosh: Safari 2.0 or later
Windows®: Intel® Pentium® III or higher, or other compatible processor
(1 GHz or higher is recommended.)
Macintosh: 1.0-GHz or higher PowerPC G4, or 1.8-GHz or higher Intel ®
Core™ processor
256 MB or more (512 MB or more is recommended for Macintosh.)
60 MB or more
CD-ROM drive or DVD drive
RJ-45
Power cord (x 1)
Power cord secure lock (x 1)
Wireless remote control (x 1)
Batteries for remote control (AA battery x 2)
Wireless Manager ME 5.5 (CD-ROM) (x 1)
Safety wire rope (x 1)
Replacement lamp unit: ET-LAF100
Replacement filter unit: ET-ACF100
Ceiling mount bracket for high ceilings: ET-PKF100H
Ceiling mount bracket for low ceilings: ET-PKF100S
Measurement, measuring conditions, and method of notation all comply with ISO 21118 international standards.
Operation range differs depending on environments.
Average value. May differ depending on models.
Weights and dimensions shown are approximate. Specifications are subject to change without notice. Product availability differs depending on region and country.
This product may be subject to export control regulations. Intel, Pentium, and Intel Core are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Microsoft, Windows Vista and Windows are either registered trademarks or trademarks of Microsoft Corp. in the
United States and/or other countries. Apple, Mac, Mac OS, and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries. PowerPC is a
trademark of International Business Machines Corporation, registered in the U.S. PJLink is a registered trademark or trademark in Japan, the United States, and other
countries and regions All other trademarks are the property of their respective trademark owners.
As of May 2009
< 3 >
S
P
E
F
C
I
L
E
PT-F300
LCD Projector
Dimensions
323
(12-23/32˝)
unit : mm (inch)
NOTE: This illustration is not drawn to scale.
13.5
(17/32˝)
53
(2-3/32˝)
432 (17˝)
311
(12-1/4˝)
115
(4-17/32˝)
128.5
(5-1/16˝)
74
(2-29/32˝)
85
(3-11/32˝)
213
(8-3/8˝)
Terminals
1
2
8
As of May 2009
3
9
4
10 11 12
567
1
LAN
2
DVI-D input
3
Computer 1 input
4
Computer 2 input/computer 1 output
5
S-Video input
6
Video input
7
Audio input for S-Video and video
8
Serial input
9
Remote input
10
Audio input for computer 1
11
Audio input for DVI-D and computer 2
12
Audio output
< 4 >
S
P
E
F
C
I
L
E
PT-F300
LCD Projector
Standard setting-up positions
369 – 449
H
Upper edge of projected image
(14-17/32˝–
17-11/16˝)
Adjustable
in 20-mm
(15/32-inch)
step
unit : mm (inch)
Ø49
(1-15/16˝)
Ø42
(1-21/32˝)
L
199
Projected image
(7-27/32˝)
H
L
Lower edge of projected image
L: Distance to screen
H: Height from the edge of screen to
center of lens
NOTE:
65
W
70 (2-3/4˝)
Illustrations show the projector installed
using optional ceiling bracket.
13 (1/2˝)
L
Projected image
This illustration is not drawn to scale.
Projection distance (screen aspect ratio 4:3)
*
Projection size
(diagonal)
0.84
1.02
1.27
1.52
1.78
2.03
2.29
2.54
3.05
3.81
5.08
6.35
7.62
m
m
m
m
m
m
m
m
m
m
m
m
m
/ 33˝
/ 40˝
/ 50˝
/ 60˝
/ 70˝
/ 80˝
/ 90˝
/ 100˝
/ 120˝
/ 150˝
/ 200˝
/ 250˝
/ 300˝
Projection distance (L)
Min (wide)
–
1.2 m
1.5 m
1.8 m
2.1 m
2.4 m
2.7 m
3.0 m
3.6 m
4.5 m
6.0 m
7.6 m
9.1 m
/
/
/
/
/
/
/
/
/
/
/
/
/
–
3.8´
4.8´
5.8´
6.8´
7.8´
8.8´
9.8´
11.8´
14.8´
19.8´
24.8´
29.8´
Max (telephoto)
1.9
2.4
3.0
3.6
4.2
4.8
5.4
6.0
7.2
9.0
12.1
15.1
18.1
m
m
m
m
m
m
m
m
m
m
m
m
m
/
/
/
/
/
/
/
/
/
/
/
/
/
Height from the edge of screen
to center of lens (H)
6.2´
7.9´
9.8´
11.8´
13.8´
15.7´
17.7´
19.7´
23.6´
29.5´
39.7´
49.5´
59.4´
0
0
0
0
0
0
0
0
0
0
0
0
0
–
–
–
–
–
–
–
–
–
–
–
–
–
0.50
0.61
0.76
0.91
1.07
1.22
1.37
1.52
1.83
2.29
3.05
3.81
4.57
m
m
m
m
m
m
m
m
m
m
m
m
m
/
/
/
/
/
/
/
/
/
/
/
/
/
0
0
0
0
0
0
0
0
0
0
0
0
0
–
–
–
–
–
–
–
–
–
–
–
–
–
1.7´
2.0´
2.5´
3.0´
3.5´
4.0´
4.5´
5.0´
6.0´
7.5´
10.0´
12.5´
15.0´
This distance is especially recommended for ceiling-mounted use and
other permanent installations.
NOTE:
Values shown are approximate. The value
for L (distance to screen) varies slightly
depending on the zoom lens characteristics.
When the shortest projection distance is
used, a small amount of distortion may
occur in the image due to the zoom lens
characteristics.
The value for H (the height from the edge
of the screen to the centre of the lens) is
the value when the horizontal optical axis
shift function is not used. The value
decreases when the horizontal optical
axis shift function is used. For details,
see Shift range on page 7.
Calculation of the projection distance
For a screen size different from the above, use the equation below to calculate the projection distance.
Aspect ratio 4:3
minimum
maximum
L (m) = (diagonal screen size in inches) x 0.0305 - 0.049
L (m) = (diagonal screen size in inches) x 0.0604 - 0.050
NOTE:
Distances calculated with the above equations will include a slight error.
As of May 2009
< 5 >
S
P
E
F
C
I
L
E
PT-F300
LCD Projector
Shift range
Optical axis shift function allows to shift the position of a projected image as shown below.
H
(Width of
projected image)
0.27H
Standard postition
of projected image
0.5V
V
(Height of
projected image)
0.5V
0.27H
Installable angle
Install the projector at an angle within the range shown below..
• Horizontal direction
The projector may not be angled horizontally.
0°
-30°
+30°
• Vertical direction
The projector may be installed at a vertical angle
of ±30°.
As of May 2009
< 6 >
S
P
E
F
C
I
L
E
PT-F300
LCD Projector
Computer data compatibility
This projector accepts up to 91 kHz horizontal scanning frequency and 162 MHz dot clock.
NOTE:
Pixel thinning is applied to signals that exceed a dot clock frequency of 150 MHz. The display resolution of this projector is 1,024
x 768 pixels. If the display resolution indicated in the above data exceeds this resolution, image compression will be used to convert the input signal to 1,024 x 768 pixels.
List of compatible signals
Display mode
Display
resolution
(dots) 1
N T SC / N T S C 4 . 4 3 / P AL -M/ PAL 6 0
720 x 480i
P A L / P A L - N / SE C A M
720 x 576i
525i(480i)
720 x 480i
625i(576i)
720 x 576i
525p(480p)
720 x 483
625p(576p)
720 x 576
750(720)/60p
1 ,2 8 0 x 7 2 0
750(720)/50p
1125(1080)/60i
1 ,9 2 0 x 1 ,0 8 0 i
1125(1080)/50i
1125(1080)/60p
1 ,9 2 0 x 1 ,0 8 0
1125(1080)/50p
1125(1080)/60p
1125(1080)/50p
V E SA
640 x 400
VG A
640 x 480
SVGA
800 x 600
MAC
XG A
832 x 624
1 ,0 2 4 x 7 6 8
WIDE750(720)
1 ,2 8 0 x 7 2 0
W X GA 7 6 8
1 ,2 8 0 x 7 6 8
W X GA 8 0 0
1 ,2 8 0 x 8 0 0
M X GA
1 ,1 5 2 x 8 6 4
MAC
MSXGA
SXGA
1 ,1 5 2 x 8 7 0
1 ,2 8 0 x 9 6 0
1 ,2 8 0 x 1 ,0 2 4
SXGA 6 0 +
1 ,4 0 0 x 1 ,0 5 0
W X GA +
U X GA
W SXG A +
W U X GA
1 ,4 4 0
1 ,6 0 0 x
1 ,6 8 0 x
1 ,9 2 0 x
x 900
1 ,2 0 0
1 ,0 5 0
1 ,2 0 0
Scanning frequency
H
V
(kHz)
(kHz)
15.7
15.6
15.7
15.6
31.5
31.3
45.0
37.5
33.8
28.1
67.5
56.3
66.6
55.6
31.5
37.9
31.5
35.0
37.9
37.5
43.3
35.2
37.9
48.1
46.9
53.7
49.7
39.6
48.4
56.5
60.0
68.7
44.8
37.1
39.6
47.8
41.3
49.1
49.7
64.0
67.5
76.7
68.7
60.0
64.0
80.0
91.1
64.0
65.1
55.9
75.0
65.3
74.6
59.9
50.0
59.9
50.0
59.9
50.0
60.0
50.0
60.0
50.0
60.0
50.0
59.9
49.9
70.1
85.1
59.9
66.7
72.8
75.0
85.0
56.3
60.3
72.2
75.0
85.1
74.6
50.1
60.0
70.1
75.0
85.0
59.9
49.8
49.9
59.9
50.0
60.2
59.8
71.2
74.9
85.0
75.1
60.0
60.0
75.0
85.0
60.0
59.9
59.9
60.0
60.0
59.9
Dot clock
frequency
(MHz)
–
–
13.5
13.5
27.0
27.0
74.3
74.3
74.3
74.3
148.5
148.5
138.5
141.5
25.2
31.5
25.2
30.2
31.5
31.5
36.0
36.0
40.0
50.0
49.5
56.3
57.3
51.9
65.0
75.0
78.8
94.5
74.5
60.5
65.3
79.5
68.0
69.1
83.5
94.2
108.0
121.5
100.0
108.0
108.0
135.0
157.5
108.0
122.4
106.5
162.0
146.3
154.0
Picture
quality 2
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
AA
AA
AA
AA
AA
A
A
A
A
A
A
A
A
A
A
A
A
A
A
B
A
A
A
B
A
B
Format
Plug and Play compatibility
RGB 2
DVI-D input
input
EDID1
EDID2
VIDEO/S-VIDEO
No
No
No
COMPUTER/YP B P R
No
No
No
DVI/COMPUTER/
YP B P R
No
Yes
No
COMPUTER
No
No
No
DVI/COMPUTER
COMPUTER
Yes
Yes
No
No
Yes
No
DVI/COMPUTER
COMPUTER
No
Yes
Yes
Yes
No
No
No
No
No
No
Yes
No
No
Yes
No
Yes
No
No
No
No
No
No
No
Yes
No
Yes
No
No
No
No
No
No
No
Yes
No
No
No
Yes
No
Yes
Yes
No
No
No
No
Yes
No
No
Yes
No
No
DVI/COMPUTER
COMPUTER
No
Yes
No
No
No
No
Yes
No
No
DVI/COMPUTER
COMPUTER
Yes
Yes
No
No
Yes
No
No
No
No
DVI/COMPUTER
COMPUTER
DVI/COMPUTER
COMPUTER
DVI/COMPUTER
COMPUTER
1. The “i” appearing after the resolution indicates an interlaced signal.
2. The following symbols are used to indicate picture quality.
AA: Maximum picture quality can be obtained. A: Signals are converted by the image processing circuit before picture is projected.
B: Pixels are thinned by the image processing circuit before picture is projected.
As of May 2009
< 7 >
S
P
E
F
C
I
L
E
PT-F300
LCD Projector
Serial connector
The serial connector complies with RS-232C. To control the projector from a personal computer, commands must be input through communication software, based on the format and satisfying the communication conditions shown below.
Pin assignments and signal names
6 9
1
5
No. Signal name
Description
No. Signal name
1
–
NC
6
–
2
TXD
Send data
7
RTS
3
RXD
Receive data
8
CTS
4
–
Connected internally
9
–
5
GND
Ground
D-sub HD 9-pin, female
Signal name
NC
Connected internally
Connected internally
NC
* Effective when connected to a PC having proper functions.
Communication conditions (factory setting)
Signal level
RS-232C-compliant
Synchronization method
Start-stop synchronization
Baud rate
9,600 bps
Parity
None
Character length
8 bits
Stop bit
1 bit
X parameter
None
S parameter
None
Basic format
Transmission from the computer begins with STX, then the ID, command, parameter, and ETX are sent
in this order. Add parameters according to the details of control.
STX
C1 C2 C3
Start
(1 byte)
:
P1 P2 P3 P4
Colon
Parameter
Command
(1 byte)
(1-4 bytes)
(3 bytes)
(Control and/or query commands)
ETX
End
(1 byte)
CAUTIION
It may not be possible to send or receive commands for about 10 to 60 seconds when the lamp is first turned on. If this occurs, wait for 60 seconds, then
try sending or receiving again. When sending multiple commands, be sure to wait for at least 0.5 second after receiving a response from the projector
before sending the next command. Additional time is sometimes required for response due to processing inside the projector. Set the time-out period for
command response to 10 seconds or more.
NOTE:
If a wrong command is received, the projector will send an ER401 command to the computer.
When sending commands without parameters, a colon (:) is not necessary.
Cable specifications
Projector
1
PC (DTE)
NC
NC
2
2
3
3
4
NC
NC
DSR
NC
6
6
7
7
8
8
9
4
5
5
As of May 2009
1
NC
NC
9
< 8 >
S
P
E
C
F
I
L
E
PT-F300
LCD Projector
Control commands
Command: <Parameter>
Function
Callback: <Parameter>
PO N * 1
PO F * 1
AV L : < p l >
II S : < i n p u t s i g n a l >
OS T
OF Z : < o f f o n >
OE N
OX G : 0
OX G : 1
OX G : 2
VP M : < N A T >
VP M : < S T D >
VP M : < C I N >
VP M : < D Y N >
VP M : < B B D >
VX X : D L V I 0 = < + 0 0 0 0 0 >
VX X : D L V I 0 = < + 0 0 0 0 1 >
VX X : D L V I 0 = < + 0 0 0 0 2 >
AU U
AU D
OM N
OC U
OC D
OC L
OC R
OA S
OS H * 1/* 2
OI X
DZ U
DZ D
TS D : < d a t e >
TS T : < t i m e >
Power on (standby mode on)
Power off (standby mode off)
Volume control
Input signal selection
The same function as “default” button
Freeze
Enter
Wide mode: Off
Wide mode: On
Wide mode: Auto
Picture mode: Natural
Picture mode: Standard
Picture mode: Cinema
Picture mode: Dynamic
Picture mode: Blackboard
Daylight View: Off
Daylight View: Auto
Daylight View: On
Volume up
Volume down
Menu
Cursor up
Cursor down
Cursor left
Cursor right
Auto setup
Shutter
Index window
Digital zoom: Enlargement
Digital zoom: Reduction
Date setting
Time setting
PON
POF
AVL:<pl>
IIS:<input signal>
OST
OFZ:<off_on>
OEN
OXG:0
OXG:1
OXG:2
VPM:<NAT>
VPM:<STD>
VPM:<CIN>
VPM:<DYN>
VPM:<BBD>
VXX:DLVI0=<+00000>
VXX:DLVI0=<+00001>
VXX:DLVI0=<+00002>
AUU
AUD
OMN
OCU
OCD
OCL
OCR
OAS
OSH
OIX
DZU
DZD
TSD:<date>
TST:<time>
*1
*2
Parameter value
Min
Max
–
–
0
–
–
0
–
–
–
–
–
–
–
–
–
–
–
–
––
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
63
–
–
1
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Do not send PON, POF, or OSH commands continuously in a short period of time. Doing so may burst the lamp or shorten the lamp replacement cycle.
When a command other than OSH is sent while the shutter function is operating, the projector will send an ER401 command in reply and release the shutter function.
Status asking commands
Command
Description
QP W
Q$ S
QI N
QA V
QV C
QV T
QV B
QV R
QV S
QW R
QW G
QW B
QH P
QV P
QC P
QD C
QS P
QL G
QX G
Standby power status
Lamp status
Input signal status
Volume adjustment value
Color adjustment value
Tint adjustent value
Brightness adjustment value
Contrast adjustment value
Sharpness adjustment value
White balance: R adjustment value
White balance: G adjustment value
White balance: B adjustment value
Horizontal position adjustment value
Vertical position adjustment value
Clock phase adjustment value
Dot clock adjustment value
Projection method status
On-screen menu language
Wide mode status
Off
On
Auto
Daylight View status
Off
Auto
On
Picture mode status
Natural
Standard
Cinema
Dynamic
Blackboard
Freeze status
Lamp run time
Shutter function status
Keystone correction status
Color temperature adjustment status
Date setting status
Time setting status
QV X : D L V I 0
QP M
QF Z
Q$ L
QS H
QK S
QT E
QG D
QG T
As of May 2009
Callback
<Parameter>
<power condition>
<lamp condition>
<input signal>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<pl>
<0>
<1>
<0>
<+00000>
<+00001>
<+00002>
<NAT>
<STD>
<CIN>
<DYN>
<BBD>
<off_on>
<acctch>
<off_on>
<pl>
<color temp>
<date>
<time>
< 9 >
S
P
E
C
F
I
L
E
PT-F300
LCD Projector
Parameter format
Parameter format
<pl>
Size (Byte)
Definition
<off on>
<input signal>
3 (1 or 2 bytes also
possible when
under control)
1
3
<installation>
<language>
1
3
<power condition>
<lamp condition>
3
1
<acctch>
<color temp>
<date>
4
1
8
<time>
6
Decimal without signs: 0-999 (000, 001, 002...999)
Decimal with signs: -99 to +99 (-99...-01, +00, +01, +02...+99)
Callback from the projector is 3 Byte.
0 = off, 1 = on
DVI = DVI-D, RG1 = computer 1, RG2 = computer 2,
NWP = network, VID = video, SVD = S-Video
0 = front, 1 = rear, 2 = ceiling and front, 3 = ceiling and rear
ENG = English, DEU = German, FRA = French, ESP = Spanish,
ITL = Italian, JPN = Japanese, CHI = Chinese, POR = Portuguese,
SVE = Swedish, NOR = Norwegian, DAN = Danish, POL = Polish,
CES = Czech, MAG = Hungarian, RUS = Russian, THA = Thai, KOR = Korean
000 = power on (standby mode on), 001 = power off (standby mode off)
0 = standby, 1 = lamp on under control, 2 = lamp off,
3 = lamp off under control
Dicimal without signs: 0000-9999 hours
0 = low, 1 = default, 2 = high
y1y2y3y4m1m2d1d2w = year (y) month (m) day (d) day of week (w)
Day of week: Monday = 1, Tuesday = 2, ... Sunday = 7
h1h2m1m2s1s2 = hour (h) minute (m) second (s)
NOTE: If a wrong command is received, the projector will send an ER401 command to the computer.
Command example
To set the volume to +30, send the command as shown below.
STX
Start
AVL
:
Command
30
ETX
Parameter
End
NOTE: When sending commands without parameters, a colon (:) is not necessary.
As of May 2009
< 10 >
S
P
E
C
F
I
L
E
PT-F300
LCD Projector
Notes on Projector Placement and Operation
The projector uses a high-wattage lamp that becomes very hot during operation.
Please observe the following precautions.
1.
Never place objects on top of the projector while it is operating.
2.
Make sure there is an unobstructed space of 500 mm (19-11/16˝) or more around the projector's exhaust openings. In addition to this space, also ensure that there is a sufficient work space for removing and installing the
lamp, filter and other parts.
3.
If the projector is placed in a box or enclosure, ensure the temperature of the air surrounding the projector is
between 0°C/32°F and 35°C/95°F. Also make sure the projector’s intake and exhaust openings are not blocked.
Take particular care to ensure that hot air from the exhaust openings is not sucked into the intake openings.
200 mm (7-7/8˝) or more
500 mm (7-5/8˝) or more
500 mm (7-5/8˝) or more
Direction of Air Intake and Exhaust
Intake
Exhaust
Operating the Projector Continuously
1.
When the projector is operated continuously 10 hours or more, the lamp replacement cycle decreases.
2.
The lamp replacement cycle also decreases when the projector is used for short periods of time (less than one hour)
repeatedly.
Replacing the Filter Unit
The projector is equipped with the Auto Cleaning Filter (ACF) function, which automatically winds the air filter to set a new
filter element in place according to operating conditions. The filter unit replacement cycle is approximately 10,000 hours.
Please purchase the ET-ACF100 filter unit for replacement use.
Weights and dimensions shown are approximate. Specifications are subject to change without notice. Product availability differs depending on region and country.
This product may be subject to export control regulations. Intel, Pentium, and Intel Core are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries. Microsoft, Windows Vista and Windows are either registered trademarks or trademarks of Microsoft Corp. in the
United States and/or other countries. Apple, Mac, Mac OS, and Macintosh are trademarks of Apple Inc., registered in the U.S. and other countries. PowerPC is a
trademark of International Business Machines Corporation, registered in the U.S. PJLink is a registered trademark or trademark in Japan, the United States, and other
countries and regions All other trademarks are the property of their respective trademark owners.
As of May 2009
< 11 >
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising