SPECIFICATIONS JFX260
FEATURES
• Ideal size and performance for rigorous all-purpose use
• 60° coverage permits creation of optimized horizontal arrays
• HF compression driver and vented LF for fully professional performance
• Asymmetric enclosure provides multiple mounting angles
• Pole mount cup & fly track, plus Omnimount®
Series 300 or similar mounting points
• Passive or bi-amplified operating modes
DESCRIPTION
The JFX260 is a 2-way multi-purpose loudspeaker. Its multifunctional design adds considerably to its value as a fullrange loudspeaker. Combining high output and natural reproduction, it is specifically outfitted to serve in a variety of both portable and permanent applications. The asymmetric enclosure provides typical angles needed for ceiling and wall mounting as well as for stage monitor operation. For permanent installation, enclosure hardware includes mounting points for an Omnimount® Series 300 or similar bracket and fly track for suspension. Provisions for portable use include a pole mount cup, top/bottom fly track for rigging, and handles integral to the enclosure that facilitate handling and transport. The JFX260 is particularly suitable as a near field main loudspeaker or as a fill/delay element in larger systems.
While the JFX260 is well suited as is for many applications, the addition of a subwoofer expands its capabilities for more demanding applications such as for houses of worship, theaters, and band PA. Six year warranty.
APPLICATION
• Portable systems or permanent installations
• Wall and ceiling mountings
• Ideal size and output for wide range of program material
• Main PA reinforcement in medium- to large-sized spaces
• Downfill for flown clusters
• High SPL stage lip / delay fill
• A/V and/or surround sound installations
• Voice & F/X reinforcement in themed attractions
PERFORMANCE
Frequency Response (1 W @ 1 m)
±3 db 90 Hz to 16 kHz
-10 dB 60 Hz
Axial Sensitivity (dB SPL, 1 W @ 1 m)
Full Range 97
LF 97
HF 104
Impedance (Ohms)
Full Range 8
LF 8
HF 8
Power Handling (Watts, continuous)
Full Range 500
LF 500
HF 200
Calculated Maximum Output (dB SPL, @ 1 m)
Full Range Peak 130
LF/HF Peak 130/133
Full Range Long Term 124
LF/HF Long Term 124/127
Nominal Coverage Angle / -6 dB points (degrees)
Horizontal 60
Vertical 45
PHYSICAL
Part Number 0002809
System Configuration 2-way, full-range crossover) or bi-amplified
LF Subsystem 1x 12-in, vented
HF Subsystem 1x 1.4-in exit/3-in voice coil neodymium compression driver on CD horn
Controls (switches, knobs) Powering mode switch
Recommended High-Pass
Frequency (24 dB/octave) 60 Hz
Enclosure Materials Exterior grade Baltic birch plywood
Finish Wear resistant textured black paint
Connectors 2x Neutrik NL4 Speakon
Hardware Pole mount cup (bottom); 2x 3position fly track (bottom); 1x
11-position fly track (top); 4x
5/16”-18 mounting points for
Omnimount Series 300 (rear)
Grille Powder coated perforated steel, foam backed
One Main Street, Whitinsville, MA 01588 508 234 6158 Toll Free 800 992 5013
EAW products are continually improved. All specifications are therefore subject to change without notice.
FAX 508 234 8251
JFX260/0004640/2 pp [email protected]
September 2002 www.eaw.com
Printed in USA
SPECIFICATIONS JFX260
DIMENSIONAL DRAWING
A
22.5°
B
45°
B
8.70
A
5.40
TOP
13.68
10.27
6.62
1.46
4.46
1.86
1.80
(7.04)
8.15
2X 6.87
19.33
22.25
(11.09)
VIEW A-A
6.50
8.50
10.75
5.00
7.00
TOP HAT
2X
HANDL
E
GRILLE PARTIALLY SHOWN
FRONT
6.75
BOTTOM
8.70
15.25
4.50
RIGHT SIDE
3.08
INPUT
BACK
.98
2.50
2X 3.44
VIEW B-B
NOTES:
1. SYMBOL INDICATES MOUNTING POINT, 3/8-16 THREADED
HOLE (PI ANGLE)
2. SYMBOL INDICATES MOUNTING POINT, 5/16-18 T-NUT FOR
SERIES 300.
3. SYMBOL INDICATES 3.00 X 1.35 FLY TRACK.
4. SYMBOL INDICATES 11.00 X 1.35 FLY TRACK.
5. SYMBOL INDICATES CENTER OF BALANCE
6. WEIGHT APPROX. 58 LBS.
7. SHIPPING WEIGHT APPROX. 64 LBS
0002810 (A) 8/12/02
Manufacturing tolerances are +/- 0.13 and +/- 1°
INPUT PANEL
WHITINSVILLE, MA USA
JFX260
S/N
FULL-RANGE
PASSIVE
PIN 1--...--
PIN 1+...+
BI-AMP
PIN 1--...LF--
PIN 1+...LF+
PIN 2--...HF--
PIN 2+...HF+
NL 4 MPR
NL 4 MPR
A & E SPECIFICATIONS
The 2-way full-range loudspeaker shall incorporate a 12-in LF cone and a 3-in voice coil neodymium HF compression driver.
The LF cone shall be mounted in a vented enclosure tuned for optimum low frequency response. The HF driver shall be loaded on a 1.4-in exit constant directivity horn with a nominal beamwidth of 60 (H) x 45 (V) degrees. An internal passive crossover network shall offer either passive or bi-amplified operation, configurable via a power mode switch on the input panel.
System frequency response shall vary no more than +3 dB from 90 Hz to 16 kHz measured on axis. When amplified using the internal passive crossover network, the loudspeaker shall produce a sound pressure level of 97 dB SPL on axis at 1 meter with a power input of 1 watt, and shall be capable of producing a peak output of 130 dB SPL on axis at 1 meter. It shall handle 500 watts of amplifier power and shall have a nominal impedance of 8 ohms. When bi-amplified, the LF section shall produce a sound pressure level of 97 dB SPL on axis at 1 meter with a power input of 1 watt, and shall be capable of producing a peak output of 130 dB SPL on axis at 1 meter. It shall handle 500 watts of amplifier power and shall have a nominal impedance of 8 ohms. The HF section shall produce a sound pressure level of 104 dB SPL on axis at 1 meter with a power input of 1 watt, and shall be capable of producing a peak output of 133 dB SPL on axis at 1 meter. It shall handle 200 watts of amplifier power and shall have a nominal impedance of 8 ohms.
The loudspeaker enclosure shall be irregularly trapezoidal in shape. It shall be constructed of exterior grade Baltic birch plywood and shall employ extensive internal bracing. It shall be finished in wear-resistant textured black paint. Input connectors shall be 2x Neutrik NL4 Speakon wired in parallel. It shall include a pole mount cup and handles integral to the enclosure. One 11-position fly track and two 3-position fly tracks shall be provided on the top and bottom of the enclosure respectively. Four 5/16"-18 threaded mounting points for use with an Omnimount® Series 300 (or similar) shall be provided on the rear of the enclosure. The front of the loudspeaker shall be covered with a foam backed, powder coated perforated steel grille.
The 2-way full-range loudspeaker shall be the EAW model
JFX260.
PHYSICAL continued
Dimensions
Weights inches
Height 22.25
Width (front) 13.68
Width (rear) 4.46
Depth 15.25
pounds
Net Weight 58
Shipping Weight 64 millimeters
565
347
113
387 kilograms
26.4
29.1
One Main Street, Whitinsville, MA 01588 508 234 6158 Toll Free 800 992 5013
EAW products are continually improved. All specifications are therefore subject to change without notice.
FAX 508 234 8251
JFX260/0004640/2 pp [email protected]
September 2002 www.eaw.com
Printed in USA