TOSHIBA e-STUDIO507 207L, 257, 307, 357, 457, 507, e-STUDIO857 557, 657, 757, 857, e-STUDIO6570C 5560C, 6560C, 6570C, e-STUDIO306LP 306LP, e-STUDIO527S 477S, 527S, e-STUDIO407CS 287CS, 347CS, 407CS, e-STUDIO5055C 2555C, 3055C, 3555C, 4555C, 5055C Network Fax Guide
Below you will find brief information for e-STUDIO6550C e-STUDIO5540C, e-STUDIO4540C e-STUDIO2040C, e-STUDIO456 e-STUDIO206L, e-STUDIO856 e-STUDIO556, e-STUDIO2550C e-STUDIO2050C. This guide explains how to send faxes (Network Fax/Internet Fax) using the N/W-Fax driver. Learn to specify recipients, set options like resolution and paper size, use the address book, and configure cover sheets. The guide covers both basic and advanced faxing functionalities, including delayed transmission and saving faxes as files.
Advertisement
Advertisement
MULTIFUNCTIONAL DIGITAL COLOR SYSTEMS /
MULTIFUNCTIONAL DIGITAL SYSTEMS
Network Fax Guide
©2012 - 2014 TOSHIBA TEC CORPORATION All rights reserved
Under the copyright laws, this manual cannot be reproduced in any form without prior written permission of TTEC.
Preface
Thank you for purchasing TOSHIBA Multifunctional Digital Systems or Multifunctional Digital Color Systems.
This manual explains the instructions for the N/W-Fax driver. Read this manual before using your
Multifunctional Digital Systems or Multifunctional Digital Color Systems. Keep this manual within easy reach, and use it to configure an environment that makes best use of the e-STUDIO’s functions.
To use this function, the scanning function (Internet Fax) and printing function (Network Fax) are required.
How to read this manual
Symbols in this manual
In this manual, some important items are described with the symbols shown below. Be sure to read these items before using this equipment.
Indicates a potentially hazardous situation which, if not avoided, could result in death, serious injury, or serious damage, or fire in the equipment or surrounding objects.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury, partial damage to the equipment or surrounding objects, or loss of data.
Indicates information to which you should pay attention when operating the equipment.
Other than the above, this manual also describes information that may be useful for the operation of this equipment with the following signage:
Describes handy information that is useful to know when operating the equipment.
Pages describing items related to what you are currently doing. See these pages as required.
Model and series names in this manual
In this manual, each model name is replaced with the series name as shown below.
Model name
e-STUDIO5540C/6540C/6550C e-STUDIO2040C/2540C/3040C/3540C/4540C e-STUDIO206L/256/306/356/456/506 e-STUDIO256SE/306SE/356SE/456SE/506SE e-STUDIO556/656/756/856 e-STUDIO556SE/656SE/756SE/856SE e-STUDIO2050C/2550C e-STUDIO2051C/2551C e-STUDIO2555C/3055C/3555C/4555C/5055C e-STUDIO2555CSE/3055CSE/3555CSE/4555CSE/5055CSE e-STUDIO287CS/347CS/407CS e-STUDIO477S/527S e-STUDIO306LP e-STUDIO5560C/6560C/6570C e-STUDIO207L/257/307/357/457/507 e-STUDIO557/657/757/857
Series name in this manual
e-STUDIO6550C Series e-STUDIO4540C Series e-STUDIO456 Series e-STUDIO856 Series e-STUDIO2550C Series e-STUDIO2551C Series e-STUDIO5055C Series e-STUDIO407CS Series e-STUDIO527S Series e-STUDIO306LP e-STUDIO6570C Series e-STUDIO507 Series e-STUDIO857 Series
Preface 1
Options
For the available options, refer to “Options” in the
Quick Start Guide
or
User’s Manual Setup Guide
for your equipment.
Screens and Operation Procedures
In this manual, the screens and the operation procedures in Windows are described for Windows 7.
The details on the screens may differ depending on how the equipment is used, such as the status of the installed options, the OS version and the applications.
If you use Windows Server 2008 R2, refer to the operation procedure for Windows 7, though the screens or the menu names, etc. may differ.
The illustration screens used in this manual are for paper in the A/B format. If you use paper in the LT format, the display or the order of buttons in the illustrations may differ from that of your equipment.
In this manual, the initial values of the setting items are underlined.
Trademarks
The official name of Windows XP is Microsoft Windows XP Operating System.
The official name of Windows Vista is Microsoft Windows Vista Operating System.
The official name of Windows 7 is Microsoft Windows 7 Operating System.
The official name of Windows 8 is Microsoft Windows 8 Operating System.
The official name of Windows Server 2003 is Microsoft Windows Server 2003 Operating System.
The official name of Windows Server 2008 is Microsoft Windows Server 2008 Operating System.
The official name of Windows Server 2012 is Microsoft Windows Server 2012 Operating System.
Microsoft, Windows, Windows NT, and the brand names and product names of other Microsoft products are trademarks of Microsoft Corporation in the US and other countries.
Apple, AppleTalk, Macintosh, Mac, Mac OS, Safari, iPhone, iPod touch, and TrueType are trademarks of
Apple Inc. in the US and other countries.
AirPrint, AirPrint logo, and iPad are trademarks of Apple Inc.
IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.
Adobe, Acrobat, Reader, and PostScript are either registered trademarks or trademarks of Adobe Systems
Incorporated in the United States and/or other countries.
Mozilla, Firefox and the Firefox logo are trademarks or registered trademarks of Mozilla Foundation in the
U.S. and other countries.
IBM, AT and AIX are trademarks of International Business Machines Corporation.
NOVELL, NetWare, and NDS are trademarks of Novell, Inc.
TopAccess is a trademark of Toshiba Tec Corporation.
Other company and product names given in this manual or displayed in this software may be the trademarks of their respective companies.
2 Preface
End User Software License Agreement
INSTALLING OR OTHERWISE USING THIS SOFTWARE PRODUCT CONSTITUTES YOUR
ACCEPTANCE OF THE FOLLOWING TERMS AND CONDITIONS (UNLESS A SEPARATE LICENSE IS
PROVIDED BY THE SUPPLIER OF APPLICABLE SOFTWARE IN WHICH CASE SUCH SEPARATE
LICENSE SHALL APPLY). IF YOU DO NOT ACCEPT THESE TERMS, YOU MAY NOT INSTALL OR USE
THIS SOFTWARE, AND YOU MUST PROMPTLY RETURN THE SOFTWARE TO THE LOCATION WHERE
YOU OBTAINED IT.
Grant of License:
This is a legal agreement between you, the end-user (“You”), and TOSHIBA TEC Corporation (“TTEC”). This software, fonts (including their typefaces) and related documentation (“Software”) is licensed for use with the system CPU on which it was installed (“System”) in accordance with the terms contained in this Agreement.
This Software is proprietary to TTEC. TTEC disclaim responsibility for the installation and/or use of this
Software, and for the results obtained by using this Software. You may use one copy of the Software as installed on a single System, and may not copy the Software for any reason except as necessary to use the
Software on a single System. Any copies of the Software shall be subject to the conditions of this Agreement.
You may not, nor cause or permit any third party to, modify, adapt, merge, translate, reverse compile, reverse assemble, or reverse engineer the Software. You may not use the Software, except in accordance with this license. No title to the intellectual property in the Software is transferred to you and full ownership is retained by TTEC. Source code of the Software is not licensed to you. You may not perform modification, deletion, etc. about copyright notice of the Software (including in duplicate).You will be held legally responsible for any copyright infringement, unauthorized transfer, reproduction or use of the Software or its documentation.
Term:
This license is effective until terminated by TTEC or upon your failure to comply with any term of this
Agreement. Upon termination, you agree to destroy all copies of the Software and its documentation. You may terminate this license at any time by destroying the Software and its documentation and all copies.
Disclaimer of Warranty:
This Software is provided “AS IS” without warranty of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability, fitness for a particular purpose, title, and noninfringement. TTEC disclaim any warranty relating to the quality and performance of the Software. If the
Software proves defective, You (and not TTEC) shall be responsible for the entire cost of all necessary servicing, repair or correction. TTEC do not warrant that the functions contained in the Software will meet your requirements or that the operation of the Software will be uninterrupted or error free.
Limitation of Liability:
IN NO EVENT WILL TTEC BE LIABLE TO YOU FOR ANY DAMAGES, WHETHER IN CONTRACT, TORT,
OR OTHERWISE (except personal injury or death resulting from negligence on the part of TTEC),
INCLUDING WITHOUT LIMITATION ANY LOST PROFITS, LOST DATA, LOST SAVINGS OR OTHER
INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO
USE THE SOFTWARE, EVEN IF TTEC OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY
OF SUCH DAMAGES, NOR FOR THIRD PARTY CLAIMS.
U.S. Government Restricted Rights:
The Software is provided with RESTRICTED RIGHTS. Use, duplication or disclosure by the U.S. Government is subject to restrictions set forth in subdivision (b) (3) (ii) or (c) (i) (ii) of the Rights in Technical Data and
Computer Software Clause set forth in 252.227-7013, or 52.227-19 (c) (2) of the DOD FAR, as appropriate.
Contractor/Manufacturer is TOSHIBA TEC Corporation, 1-11-1, Osaki, Shinagawa-ku, Tokyo, 141-8562,
Japan
General:
You may not sublicense, lease, rent, assign or transfer this license or the Software. Any attempt to sublicense, lease, rent, assign or transfer any of the rights, duties or obligations hereunder is void. You agree that you do not intend to, and will not ship, transmit (directly or indirectly) the Software, including any copies of the
Software, or any technical data contained in the Software or its media, or any direct product thereof, to any country or destination prohibited by the United States Government. This license shall be governed by the laws of Japan or, at the election of a Supplier of TTEC concerned with a dispute arising from or relating to this
Agreement, the laws of the Country designated from time to time by the relevant Supplier of TTEC. If any provision or portion of this Agreement shall be found to be illegal, invalid or unenforceable, the remaining provisions or portions shall remain in full force and effect.
End User Software License Agreement 3
YOU ACKNOWLEDGE THAT YOU HAVE READ THIS LICENSE AGREEMENT AND THAT YOU
UNDERSTAND ITS PROVISIONS. YOU AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS. YOU
FURTHER AGREE THAT THIS LICENSE AGREEMENT CONTAINS THE COMPLETE AND EXCLUSIVE
AGREEMENT BETWEEN YOU AND TTEC AND ITS SUPPLIERS AND SUPERSEDES ANY PROPOSAL
OR PRIOR AGREEMENT, ORAL OR WRITTEN, OR ANY OTHER COMMUNICATION RELATING TO THE
SUBJECT MATTER OF THIS LICENSE AGREEMENT.
TOSHIBA TEC Corporation, 1-11-1, Osaki, Shinagawa-ku, Tokyo, 141-8562, Japan
4 End User Software License Agreement
CONTENTS
Chapter 1 OVERVIEW
Chapter 2 SENDING A FAX
Chapter 3 SETTING OPTIONS
Chapter 4 APPENDIX
CONTENTS 5
6 CONTENTS
1.
OVERVIEW
This chapter provides an overview of the Network Fax features.
1 OVERVIEW
Features and Functions
This equipment provides the network fax features, which simplify and facilitate your office facsimile needs and enables you to send fax or Internet Fax digital documents directly from your desktop.
Fax transmission using the N/W-Fax driver is available only when the optional Fax unit is installed.
Please enable the SNMP setting on TopAccess to use the N/W-Fax functions. In addition, the N/W-Fax driver does not work if the SNMP setting on TopAccess is disabled when the optional Fax unit is installed.
The highly intuitive, network N/W-Fax driver software enables you to select the fax printer driver to electronically fax or Internet Fax from your computer to one or more recipients. You can easily define fax job properties from the send list to fax resolutions. The N/W-Fax driver is complimented with the AddressBook
Viewer. The combination of applications enables you easily to manage a selection of fax recipients and access to the address book.
The N/W-Fax driver enables you to set up send lists and send electronic documents from your PC to one or more destinations. You send to the fax in much the same way you would choose to print to a designated printer that makes using the N/W-Fax driver quick and simple. You can select the fax properties. Fax properties are the attributes you can set to define sender and recipient information for processing fax jobs such as dialing options, sender information, fax resolution and page layout.
Other features include an easy-to-use fax scheduler that allows you to set up a date and time to transmit your fax. Cover page options are also provided. You can include a customized cover page with your fax transmission that can contain sender and recipient fax information and a detailed message. You can easily maintain sender and contact information that can be printed on the cover pages.
Faxing hard-copy documents must be performed from the touch panel display.
The image quality of the originals that are sent by the N/W-Fax driver is different from the originals that are sent by the general fax operation.
If you specify the Email addresses as the recipients using the N/W-Fax driver, the document will be sent as an Internet Fax. The Internet Fax feature allows users to send originals the same as the fax features.
However, an Internet Fax is sent through the Internet, although a fax is sent through the public switched telephone line. In order to send an Internet Fax, the remote device also must support the Internet Fax feature.
For more details about the Internet Fax, refer to the
Scanning Guide
or
User’s Manual Advanced
Guide
.
8 Features and Functions
2.
SENDING A FAX
This chapter describes how to send a fax using a N/W-Fax driver.
2 SENDING A FAX
Basic Procedure
The basic procedure for sending a fax (Network Fax / Internet Fax) is as follows.
You can use standard functions or set optional functions as well as the basic ones described in this section.
For these operations, see the following section.
1
Start the application software and prepare the document to be sent.
2 Select [Print] from the [File] menu in the application software.
The procedure for displaying the print dialog box may differ from the above depending on the application software.
3 Select [TOSHIBA e-STUDIO Fax] for the printer and click [Preferences].
The dialog box of the N/W-Fax driver properties appears.
Note that the command name to open the driver properties may differ from [Preferences] depending on the application software.
10 Basic Procedure
2.SENDING A FAX
4
Click the [Send] tab and specify the recipients.
2 SENDING A FAX
5
To specify recipients, enter them with the keyboard or select them from the address book.
On the [Send] tab, you can set the resolution of a fax cover sheet, etc. as well as specifying the recipients.
P.30 “Setting up the [Send] tab”
On the [Layout] tab, you can set the size and the orientation of the paper.
P.29 “Setting up the [Layout] tab”
On the [Cover Sheet] and [Sender Information Properties] tab, the sender information for adding a fax cover sheet can be set.
P.33 “Setting up the Cover Sheet”
Click [OK].
The transmission settings are determined and the N/W-Fax driver properties dialog box is closed.
Basic Procedure 11
2 SENDING A FAX
6
Click [Print] in the print dialog box on the application software.
A fax starts being sent.
Note that the command name to print a document (send a fax) may differ from [Print] depending on the application software.
A waiting fax job can be checked or deleted through the managing jobs function in TopAccess. A sent fax job can also be checked through the displaying job logs function in TopAccess. For details, refer to the
TopAccess Guide
.
Cautionary points when the [Enter the user credentials manually] option is used
When this option is enabled on this equipment, you are prompted to enter your user name and password before sending a fax.
When the dialog box below appears, enter your user name and password, and then click [OK].
Up to 128 characters can be entered in the [User Name] box, and up to 64 characters in the [Password] box.
The values entered in the above boxes are not stored. Therefore, you must enter your user name and password every time you send a fax.
You can make settings for this option on the [Device Settings] tab.
P.36 “Setting up the [Device Settings] tab”
12 Basic Procedure
2 SENDING A FAX
2.SENDING A FAX
Cautionary points when LDAP authentication is used
When LDAP authentication is enabled on this equipment, you must specify an LDAP server in the [Server
Name] box on the [Send] tab before sending a fax.
If you attempt to send a fax without specifying an LDAP server, the [Specify LDAP Server] dialog box will appear to ask you to do so.
In this case, specify the desired LDAP server in the [Server Name] box and click [OK] to send the fax.
You can make settings for LDAP authentication on the [Device Settings] tab.
P.36 “Setting up the [Device Settings] tab”
Basic Procedure 13
2 SENDING A FAX
Specifying Recipients
Up to 400 recipients can be specified in a single operation. For equipment with no hard disk installed, up to 80 recipients can be specified in a single operation.
To send a Network Fax, specify the fax number. To send an Internet Fax, specify the Email address.
P.14 “Entering recipients from the keyboard”
P.16 “Selecting recipients from the address book”
P.18 “Selecting recipients from the address book (Search option)”
To use the address book, you need to register recipients in the address book of AddressBook Viewer in advance.
If more than one recipient is specified in a single transmission, and a cover sheet is set in the N/W-Fax driver or a header page is set to be printed on the recipient's device, all the recipient information may be printed. If you want to secure the recipient information, avoid sending a fax to multiple recipients at the same time.
Entering recipients from the keyboard
You can enter a recipient with the keyboard.
1
For the recipient of a Network Fax, click [Fax Number] and enter the fax number in the right-hand box. For one of an Internet Fax, click [Internet Fax Address] and enter the
Email address in the right-hand box.
14 Specifying Recipients
2 SENDING A FAX
2.SENDING A FAX
When you enter a fax number, you can also enter a sub address and a password. Click [SUB/
PWD] to enter them (within 20 digits each) in the dialog box. Entering them enables the document to be transferred from the recipient’s device to that of the sub-address, as the communication is in compliance with ITU-T standard. However, in order to use this function, the recipient’s device must be a model in compliance with the ITU-T standard.
Use “ - ” (hyphen) if you send a Network Fax with pauses (approx. 3 seconds) inserted in the fax number.
2 Click .
The recipients selected for “To” are listed.
When the fax transmission is completed, the recipients are automatically removed from the “To” list.
Specifying Recipients 15
2 SENDING A FAX
Selecting recipients from the address book
Select a recipient from the address book in the AddressBook Viewer.
1
Click [Address Book].
2
The AddressBook Viewer runs.
When selecting a fax number after selecting a contact from the contact list, click [Select
Fax] and when selecting an Email address, click [Select Email].
The selected recipients are listed in the “Selected Fax” or “Selected Email”.
A contact, for which only a fax number is registered, cannot be displayed in the “Selected Email” and a contact, for which only an Email address is registered, cannot be displayed in the “Selected Fax”.
16 Specifying Recipients
2 SENDING A FAX
2.SENDING A FAX
You can select a recipient by the following operations:
Selecting a contact by dragging and dropping
Drag a contact in the contact list and drop it to the “Selected Fax” or “Selected Email”.
Selecting a contact by double-clicking on it
Double-click on a contact in the contact list. To change the setting of the recipient to be selected upon double-clicking, select [Default Configuration], [Type Selection] in the [View] menu and then one of
[Fax], [Email] and [Both].
Selecting a contact from a shortcut menu
Right-click on the contact in the contact list, select [Select] from the shortcut menu and then either [Fax
Number] and [Email].
3
Removing a recipient
Select a recipient in the “Selected Fax” or “Selected Email” and click the corresponding [Remove] (Left: fax number, Right: Email address).
Click [OK].
The AddressBook Viewer is closed and the recipients selected for “To” are listed.
When the fax transmission is completed, the recipients are automatically removed from the “To” list.
Specifying Recipients 17
2 SENDING A FAX
Selecting recipients from the address book (Search option)
You can find and select a recipient from the address book in the AddressBook Viewer.
1
Click [Address Book].
2
The AddressBook Viewer runs.
Select [Find] from the [Edit] menu.
The [Find Contact] dialog box appears.
18 Specifying Recipients
2.SENDING A FAX
3
Select a registered directory service in [Data Source].
2 SENDING A FAX
To change the setting of the default address book in the [Data Source] box, select [View] - [Default
Configuration] - [Data Source] and then choose an address book.
Specifying Recipients 19
2 SENDING A FAX
4
Display the [Person] tab and enter search strings in the following boxes.
Display Name
— To search display names, enter a search string here.
Fax Number
— To search fax numbers, enter the numbers here.
— To search Email addresses, enter a search string here.
If you perform searching in the above conditions, proceed to step 6. If you want to set more detailed search conditions, proceed to step 5 and set the [Detail Setting] tab. Note that even if you enter the search conditions in both the [Person] and [Detail Setting] tabs, you cannot perform searching in this combination.
In the [Person] tab, you do not have to fill in all the boxes and the string does not need to completely correspond to the target of the search. Entering one or more characters in one or more boxes causes a search to be made for contacts which correspond to the particular conditions.
20 Specifying Recipients
2 SENDING A FAX
2.SENDING A FAX
5
Display the [Detail Setting] tab, set the search condition, and then click [Add].
Field Select
— Select an item to be searched.
Condition of search string
— Select a condition in the left-hand box, and then enter a search string in the right-hand box.
The search condition is displayed in the “Condition list”.
To set more than one search condition, repeat this operation as many times as needed.
To delete the search conditions, select one and click [Remove].
Specifying Recipients 21
2 SENDING A FAX
6
Click [Search].
It starts searching contacts in the selected address book. When the search is complete, the contacts matching the search conditions are listed.
To stop searching, click [Stop].
Even if you enter the search conditions in both the [Person] and [Detail Setting] tabs, only the search condition in the tab currently displayed is used. You cannot perform searching in the combined conditions on both tabs.
22 Specifying Recipients
2 SENDING A FAX
2.SENDING A FAX
7
Drag and drop the contacts to “Selected Fax” or “Selected Email” from the list of the search results.
The selected recipients are listed in “Selected Fax” or “Selected Email”.
A contact, for which only a fax number is registered, cannot be displayed in the “Selected Email” and a contact, for which only an Email address is registered, cannot be displayed in the “Selected Fax”.
You can select a recipient by the following operations:
Selecting a contact by double-clicking on it
Double-click on a contact in the list of the search results. To change the setting of the recipient to be selected upon double-clicking, select [Default Configuration], [Type Selection] in the [View] menu and then one of [Fax], [Email] and [Both].
Selecting a contact from a shortcut menu
Right-click on the contact in the list of the search results, select [Select] from the shortcut menu and then either [Fax Number] or [Email].
Removing a recipient
Select a recipient in the “Selected Fax” or “Selected Email” and click the corresponding [Remove] (Left: fax number, Right: Email address).
Specifying Recipients 23
2 SENDING A FAX
8
Click [OK].
The AddressBook Viewer is closed and the recipients selected for “To” are displayed on the list.
When the fax transmission is completed, the recipients are automatically removed from the “To” list.
Removing recipients
You can remove a recipient from the “To” list in the N/W-Fax driver properties.
1
Select a recipient and click [Remove].
The selected recipient is removed.
24 Specifying Recipients
3.
SETTING OPTIONS
This chapter describes how to set up options for the N/W-Fax driver.
3 SETTING OPTIONS
How To Setup
There are two ways to set the N/W-Fax driver options: One is to set the initial values of the options and the other is to set each option for each individual job.
P.26 “Setting Initial Values of the N/W-Fax driver options”
P.28 “Setting print options for each print job”
Setting Initial Values of the N/W-Fax driver options
Setting the N/W-Fax options by displaying the N/W-Fax driver properties from the Printers folder on the
Windows [Start] menu will establish the initial values of the options.
1
2
Click the Start button and then select [Devices and Printers].
When using Windows XP / Windows Server 2003, click [Start] and select [Printers and Faxes].
When using Windows Vista / Windows Server 2008, click [Start] and select [Control Panel],
[Hardware and Sound] and then [Printers].
When using Windows 8 or Windows Server 2012, see the following section to open the [Devices and Printers] folder.
P.26 “Accessing the printers folder on Windows 8 / Windows Server 2012”
Right-click [TOSHIBA e-STUDIO Fax], and then select [Printing preferences] or [Printer properties] from a shortcut menu.
When using Windows XP / Windows Vista / Windows Server 2003 / Windows Server 2008, select
[TOSHIBA e-STUDIO Fax], click the [File] menu and then select [Printing Preferences] or
[Properties].
If [File] menu is not displayed, press [Alt].
Accessing the printers folder on Windows 8 / Windows Server 2012
Follow the steps below to access the printers folder on Windows 8 / Windows Server 2012.
1 Move the cursor to the upper right corner or lower right corner of the computer screen, and then select [Start] in the menu that appears.
The [Start] screen appears.
26 How To Setup
3 SETTING OPTIONS
3.SETTING OPTIONS
2
Right-click in the blank area in the [Start] screen, and then click [All apps] that appears.
The [Apps] screen appears.
3 Click [Control Panel].
The [All Control Panel Items] screen appears.
How To Setup 27
3 SETTING OPTIONS
4
Click [Devices and Printers].
The [Devices and Printers] folder appears.
Setting print options for each print job
Setting the N/W-Fax driver options by displaying the printer properties from the Print dialog box within an application will establish the values for the current N/W-Fax job. The N/W-Fax driver option settings specific to each N/W-Fax job are set using this method.
1
2
Click the [File] menu and select [Print] on an application.
Select [TOSHIBA e-STUDIO Fax] and click [Properties] or [Preferences].
28 How To Setup
3 SETTING OPTIONS
Setting up the N/W-Fax Driver Options
N/W-Fax driver options are the attributes to define the way a fax job is transmitted. For example, you can specify the recipients, resolution, and paper size.
P.29 “Setting up the [Layout] tab”
P.30 “Setting up the [Send] tab”
P.33 “Setting up the Cover Sheet”
P.36 “Setting up the [Device Settings] tab”
P.37 “Setting up LDAP servers”
Setting up the [Layout] tab
On the [Layout] tab, you can set the size and the orientation of the paper.
1
2
1) Orientation
Set the printing orientation of the document.
-
Portrait
— Data are printed vertically to the paper.
-
Landscape
— Data are printed horizontally to the paper.
2) [Advanced]
Click this to display the [Advanced Option] dialog box. You can select the paper size of the document.
Setting up the N/W-Fax Driver Options 29
3 SETTING OPTIONS
Setting up the [Send] tab
In the [Send] tab, you can specify the recipients and how the fax will be sent.
1
2
3
10
11
14
15
17
4
6
7
5
8
9
12
13
16
18
1) [Address Book]
Click to launch the AddressBook Viewer. You can select recipients from the address book.
P.16 “Selecting recipients from the address book”
2) To
This displays the specified recipients list.
3) [Remove]
Select a recipient in the [To] list and click this to remove the recipient from the list.
4) Fax Number
Enter the recipient’s fax number directly.
P.14 “Entering recipients from the keyboard”
5) [SUB/PWD]
Click this to display the [SUB/PWD] dialog box. You can add a sub address and a password to the entered fax number.
P.14 “Entering recipients from the keyboard”
6) Internet Fax Address
Enter the recipient’s Internet Fax number directly.
P.14 “Entering recipients from the keyboard”
7) Resolution
Select the resolution for the fax.
-
Standard (200 x 100 dpi)
— Select this to send a document in Standard mode (200 x 100 dpi).
-
Fine (200 x 200 dpi)
— Select this to send a document in Fine mode (200 x 200 dpi).
-
Super Fine (200 x 400 dpi)
— Select this to send a document in Super Fine mode (200 x 400 dpi).
-
Ultra Fine (400 x 400 dpi)
— Select this to send a document in Ultra Fine mode (400 x 400 dpi).
30 Setting up the N/W-Fax Driver Options
3 SETTING OPTIONS
3.SETTING OPTIONS
8) Department Code
Enter a department code of 1 to 63 characters if required. When the department code is enabled on this equipment, you must enter it to send a fax.
If you do not enter a department code when it is enabled on the equipment and the [Invalid
Department Code Print Job] is set to “Store to invalid job list” in TopAccess, the job will be stored in the Invalid job list without being transmitted. You can print or delete a stored job from the [JOB
STATUS] on the touch panel. For instructions on how to print or delete a job in the Invalid job list, refer to the
Printing Guide
or
User’s Manual Advanced Guide
.
If you do not enter the department code when the department code is enabled on the equipment and the [Invalid Department Code Print Job] is set to PRINT in TopAccess, the job will be sent.
If you do not enter the department code when the department code is enabled on the equipment and the [Invalid Department Code Print Job] is set to DELETE in TopAccess, the job will be deleted automatically.
9) Hide Department Code
Select this check box to display a department code in the blank symbols.
10)Cover Sheet
Select a cover sheet type among [Standard Cover Page], [Business Cover Page] and [Professional Cover
Page] if you want to attach a cover sheet to the first page of the document.
P.40 “Sending with a cover sheet”
11)[Edit]
Click this to display the [Cover Sheet Settings] dialog box. You can perform various kinds of editing on the cover sheet selected in the Cover Sheet setting, such as entering a subject or a message, or changing the type or size of the fonts.
P.33 “Setting up the Cover Sheet”
12)Server Name
Select the desired LDAP server in the [Server Name] box if needed.
You can make settings for the LDAP server on the [Device Settings] tab.
P.36 “Setting up the [Device Settings] tab”
13)[SNMP Settings]
Click this to check or change the SNMP settings.
14)Delayed Fax
Select this to send a document on a specified date and time. When this is selected, click [Edit] to display the [Scheduled Time] dialog box and specify date and time the job will be transmitted. The job sent to this equipment will be stored in the Fax queue until the specified date and time.
15)Save as File
Select this to save up to 10 GB of documents in the “FILE_SHARE” folder in the equipment as well as send the document as a fax and Internet Fax.
Your scans can be saved in the equipment's shared folder (MFP LOCAL) only when the hard disk is installed in the equipment.
When the cover sheet is set, the cover sheet and the original will be stored in the “FILE_SHARE” folder.
Setting up the N/W-Fax Driver Options 31
3 SETTING OPTIONS
16)File Format
Select the file format of the document that will be saved. This option can be selected only when the [Save as File] check box is selected.
17)[Restore Defaults]
Click this to restore the default setting values.
18)[Help]
Click this to browse Help for the N/W-Fax driver.
32 Setting up the N/W-Fax Driver Options
3 SETTING OPTIONS
3.SETTING OPTIONS
Setting up the Cover Sheet
You can set the content of the cover sheet to be attached to a fax.
P.40 “Sending with a cover sheet”
1
2
3
4
5
6
7
8
9
10
1) Preview
The image of the cover sheet can be previewed. You can check the layout of the character strings and images.
Depending on the line feed positions, the preview may not duplicate the actual print result of the cover sheet, but is used for checking its layout.
If the contents are on more than one page, such as the many line feeds included in “Sender
Information” or “Message”, only the first one page is displayed in the preview.
2) Fonts
Select the font to be used for the cover sheet. Select the section for which the font is used, and then click
[Edit] to select the type, style and size of the font.
-
Header
— Set the font to be used for the header of the cover sheet.
-
Title
— Set the font to be used for the title such as Reference Number, Recipients Information, Sender
Information, Subject or Message.
-
Body
— Set the font to be used for the body of each title.
3) Footer
Select an image file to be attached to the footer of the cover sheet.
-
[Browse]
— Click this to select an image file to be attached to the footer within 1 MB.
-
[Delete]
— Click this to delete the attached image file.
-
Position
— Select the position of the image file from the left, center and right.
4) Header Text
Enter a title to be displayed on the header of the cover sheet; it can be up to 63 characters.
5) Reference Number
Check this to have a reference number identifying the fax to appear on the cover sheet. Enter the reference number in the text box.
6) Recipient’s Information
Check this to have the recipient’s information appear on the cover sheet. Select the desired information among the options below.
-
Name
— Check this to have the recipient name appear on the cover sheet.
Setting up the N/W-Fax Driver Options 33
3 SETTING OPTIONS
-
Company
— Check this to have the recipient company name appear on the cover sheet.
-
Department Name
— Check this to have the recipient department name appear on the cover sheet.
-
Fax Number
— Check this to have the recipient fax number or Email address appear on the cover sheet.
7) Sender Information
Check this to have the sender’s information appear on the cover sheet. You can enter the information in up to 500 characters.
8) Subject
Check this to have a subject appear on the cover sheet. You can enter the subject in up to 40 characters.
9) Message
Check this to have a message appear on the cover sheet. You can enter the message in up to 500 characters.
10)[Restore Defaults]
Click this to restore the default setting values.
Setting up the SNMP
If the recipient’s TOSHIBA MFP is not found over the Internet and the fax job is not sent normally, the SNMP settings may be the cause. Check that the SNMP settings are correct in the [SNMP Settings] dialog box, and if not, change them.
Ask the administrator for details on the SNMP Network settings configured for your TOSHIBA MFP.
1
2
3
4
1) Version
Be sure to have the correct SNMP version set for your TOSHIBA MFP and select from the following options:
-
V1/V2
— Select this option to enable SNMP V1 and V2.
-
V3
— Select this option to enable SNMP V3.
-
V1/V2/V3 (for [Discovery Settings] dialog box only) —
Select this option to enable SNMP V1, V2, and V3.
34 Setting up the N/W-Fax Driver Options
3 SETTING OPTIONS
3.SETTING OPTIONS
2) SNMP V1/V2
Community Name
— If a community name other than “private” (default) is set for the SNMP community name for your TOSHIBA MFP, enter its community name.
To send fax jobs normally under an SNMP V1/V2 environment, the SNMP community names must be the same in the 3 settings shown below. For help, ask your administrator.
- Your TOSHIBA MFP
- [SNMP Settings] dialog box of the [Sender Information] tab
- TCP/IP port of the [Ports] tab in the N/W-Fax driver
To change the community name, the administrator privilege is necessary. You must log in with the
“Administrator” privilege and open the printer driver properties.
Up to 31 characters including the following symbols can be entered for the Community Name.
! " # $ % & ' ( ) * + , - / : ; < = > ? @ [ \ ] ^ _ ` { | } ~
3) SNMP V3
If SNMP V3 is enabled, select one of the following items to set how users are authenticated.
User ID File —
Select this option when you want to use a user ID file. Click [Browse] and specify the user
ID file.
User Name/Password —
Select this option when you want to use the user name and password. When this option is selected, keyboard or select the following items:
-
User Name
-
Authentication Protocol
-
Authentication Password
-
Privacy Protocol
-
Privacy Password
If you select to enable SNMP V3, consult your network administrator for preliminary advice on how to authenticate users.
Up to 31 characters including the following symbols can be entered for each of the User Name,
Authentication Password and Privacy Password.
! $ % & ' ( ) - , < > @ [ ] ^ _ ` { } ~
Setting up the N/W-Fax Driver Options 35
3 SETTING OPTIONS
4) [Restore Default]
Click this button when you want to reset all the settings back to the defaults.
Setting up the [Device Settings] tab
On the [Device Settings] tab, you can change a setting for N/W-Fax driver update or display the software version of the driver.
Ask the administrator for details on the settings configured for your TOSHIBA MFP.
1
2
4
5
6
3
7
1) Update Automatically
Select whether or not the setting information of each item on the [Device Settings] tab of the N/W-Fax driver is to be obtained by automatically communicating with your TOSHIBA MFP every time this tab is opened.
-
On
— Select this to obtain the setting information automatically.
-
Off
— Select this not to obtain the setting information automatically. Set each item manually.
2) User Authentication
Select the authentication method which is to be used. Set it to correspond to that of your TOSHIBA MFP.
-
Off
— Select this not to perform user authentication.
-
MFP Local Authentication
— Select this to perform MFP Local Authentication.
-
Windows Domain Authentication
— Select this to perform Windows Domain Authentication.
-
LDAP Authentication
— Select this to perform LDAP Authentication.
3) [Details]
When you click this button, the [LDAP Server Settings] dialog box will appear. This option can be selected only when [LDAP Authentication] is selected in the [User Authentication] box.
P.37 “Setting up LDAP servers”
4) Enter the user credentials manually
When this check box is selected, you are prompted to enter your user name and password every time you send a fax. This option is available when any of MFP Local Authentication, Windows Domain
Authentication, or LDAP Authentication is selected in the [User Authentication] box.
To configure this option, select [Off] in the [Update Automatically] box.
This option can be used together with any of the user authentication functions (MFP Local
Authentication, Windows Domain Authentication, LDAP Authentication).
5) Fax Function
Select whether or not the fax function is enabled. Set it to correspond to that of your TOSHIBA MFP.
-
Enabled
— Select this to enable the fax function.
-
Disabled
— Select this to disable the fax function.
36 Setting up the N/W-Fax Driver Options
3 SETTING OPTIONS
3.SETTING OPTIONS
6) Internet Fax Function
Select whether or not the Internet Fax function is enabled. Set it to correspond to that of your TOSHIBA
MFP.
-
Enabled
— Select this to enable the Internet Fax function.
-
Disabled
— Select this to disable the Internet Fax function.
7) [Version Information]
Click this to display the software version information of the N/W-Fax driver.
Setting up LDAP servers
The [LDAP Server Settings] dialog box allows you to register LDAP servers.
3
4
1
2
5
1) [Update Now]
Click this button to obtain LDAP server information automatically from your TOSHIBA MFP, and register it in [Server Name List].
2) Server Name
Enter the desired LDAP server in this box if needed.
Up to 64 characters (excluding # ; \ =) can be entered for the [Server Name] box.
3) [Add]
Click this button to register the LDAP server in the [Server Name List], which has been entered in the
[Server Name] box.
4) Server Name List
The registered LDAP servers are displayed in this list. Up to 16 LDAP servers can be registered.
5) [Delete]
Click this button to delete an LDAP server in [Server Name List]. Select the LDAP server that you want to delete in the list, and click this button.
Setting up the N/W-Fax Driver Options 37
3 SETTING OPTIONS
Sending With Extended Fax Functionality
The N/W-Fax driver allows users to perform the following features.
P.40 “Sending with a cover sheet”
Saving a fax as a file
You can save a document in the “TXFAX” folder in the “FILE_SHARE” folder in this equipment as well as sending the document to fax numbers and Email addresses.
Your scans can be saved in the equipment's shared folder (MFP LOCAL) only when the hard disk is installed in the equipment.
1 Display the [Send] tab and select the [Save as File] check box.
2 Select the file format in the [File Format] box.
3
4
Specify the other options to send a document and click [OK].
Click [OK] (or [Print]) to send a document to this equipment.
The document is saved in the “TXFAX” folder in the “FILE_SHARE” folder in this equipment.
The saved file contains the cover sheet when the cover sheet is set.
Since the image smoothing function does not work for the image stored in the “FILE_SHARE” folder, its printing image quality differs from the normal fax image quality.
38 Sending With Extended Fax Functionality
3 SETTING OPTIONS
3.SETTING OPTIONS
Delayed transmission
When the delayed transmission is specified, the fax is stored in the fax queue in this equipment and will be sent at the specified date and time.
1
Display the [Send] tab and select the [Delayed Fax] check box.
2
3
Click [Edit].
The [Scheduled Time] dialog box appears.
Select the date and time and click [OK].
You can click the Date arrow to display a calendar that allows you to select a date.
Enter the time to commence the fax transmission. You can use the up and down arrows to assist with setting the time in the proper format.
The scheduled date cannot be more than one month from the current date. If the current month does not have a date like the current one, then the date will be set at the last day of the following month. For example, if the current date is March 31st, then the maximum date that can be selected for the scheduled fax is April 30th.
4
Specify the other options to send a document and click [OK].
5 Click [OK] (or [Print]) to send a document to this equipment.
Sending With Extended Fax Functionality 39
3 SETTING OPTIONS
Sending with a cover sheet
You can choose to send a cover sheet with your fax transmission. The cover sheet is merged with the recipient [To] list data to create a fax cover sheet. You can select what to include on the cover sheet such as sender or recipient information.
When a printer driver whose name consists of 54 letters or more is specified for the default printer and an attempt is made to send a fax with a cover sheet added from Microsoft Excel using a N/W-Fax driver with an IPP port, an XL error may occur and fax transmission may be impossible. (This error does not occur in application software other than Microsoft Excel.)
If this error occurs, perform one of the following and start sending a fax again.
Use 30 letters or less for the N/W Fax driver name.
Do not attach any cover sheet.
1 Display the [Send] tab, select the cover sheet type in the [Cover Sheet] box and then click [Edit].
The [Cover Sheet Settings] dialog box appears.
40 Sending With Extended Fax Functionality
3.SETTING OPTIONS
2
Enter the title of the cover sheet in the [Header Text] box.
3 SETTING OPTIONS
3
You can enter up to 63 characters for the header text.
If you want a reference number identifying the document to appear on the cover sheet, select the [Reference Number] check box and then enter the reference number in the text box.
You can enter up to 20 characters for the reference number.
Sending With Extended Fax Functionality 41
3 SETTING OPTIONS
4
If you want the recipient’s information to appear on the cover sheet, select the
[Recipient Information] check box and then select the options required for the recipient information.
Name
— Check this to have the name of the recipient appear on the cover sheet.
Company
— Check this to have the company name of the recipient appear on the cover sheet.
Department Name
— Check this to have the department name of the recipient appear on the cover sheet.
Fax Number
— Check this to have the fax number or Email address of the recipient appear on the cover sheet.
Recipient information is obtained from the address book. If the recipient is added manually, this information does not appear on the cover sheet except for the fax number or Email address.
The recipient information for all recipients will appear on the cover sheet.
5
If you want sender information to appear on the cover sheet, select the [Sender
Information] check box and then enter the sender information in the text box.
You can enter up to 500 characters for the sender information.
42 Sending With Extended Fax Functionality
3 SETTING OPTIONS
3.SETTING OPTIONS
6
If you want a subject to appear on the cover sheet, select the [Subject] check box and then enter the subject in the text box.
You can enter up to 40 characters for the subject.
7
If you want a message to appear on the cover sheet, select the [Message] check box and then enter the message in the text box.
8
You can enter up to 500 characters for the message.
If you want to change the font of the characters on the cover sheet, select the corresponding section in the [Font for] box, and then click [Edit].
The [Font] dialog box appears.
If you do not change the font, proceed to step 10.
Sending With Extended Fax Functionality 43
3 SETTING OPTIONS
9
Select the desired one from each of the [Font], [Font style], [Size] and [Script] boxes, and then click [OK].
The [Font] dialog box is closed and the font settings are determined for the selected section.
If you want to change the font of other sections, repeat the procedure from step 8.
10
If you want to attach an image file on the footer, click [Browse] of Image File.
The [Open] dialog box appears.
If you do not attach an image file, proceed to step 13.
44 Sending With Extended Fax Functionality
3.SETTING OPTIONS
11
Select an image file to be attached and then click [Open].
3 SETTING OPTIONS
The [Open] dialog box is closed and the selected image file is attached.
Attach the image file in a bitmap format (.bmp) within 1 MB.
12
Select the position of the image file.
- Select this to align the image to the left.
- Select this to align the image to the center.
- Select this to align the image to the right.
13 Specify the other options to send a document and click [OK].
14
Click [Print] to send a document to this equipment.
Sending With Extended Fax Functionality 45
4.
APPENDIX
This chapter shows the cover sheet samples.
4 APPENDIX
Cover Sheet Samples
Standard cover page
Reference Number:
0000000000000000
To:
00000000001
From:
MFP-00C67861
Subject:
N/W-Fax Document
Message:
This is a N/W-Fax Document.
48 Cover Sheet Samples
4.APPENDIX
Business cover page
Reference Number:
0000000000000000
To:
00000000001
From:
MFP-00C67861
Subject:
N/W-Fax Document
Message:
This is a N/W-Fax Document.
4 APPENDIX
Cover Sheet Samples 49
4 APPENDIX
Professional cover page
Reference Number:
0000000000000000
To:
00000000001
From:
MFP-00C67861
Subject:
N/W-Fax Document
Message:
This is a N/W-Fax Document.
50 Cover Sheet Samples
INDEX
A
Add
..........................................................................37
Address Book
...............................................16
AddressBook Viewer
........................................... 16
Advanced
..................................................................29
B
Basic procedure
.........................................................10
Business cover page
..................................................49
C
Community Name
......................................................35
Cover Sheet
....................................................... 31
D
Delayed Fax
....................................................... 31
Delete
.......................................................................37
Department Code
......................................................31
Details
......................................................................36
[Device Settings] tab
..................................................36
E
Edit
..........................................................................31
Enter the user credentials manually
F
Fax Function
.............................................................36
Fax Number
..............................................................30
File Format
......................................................... 32
Fonts
........................................................................33
Footer
.......................................................................33
H
Header Text
..............................................................33
Help
.........................................................................32
Hide Department Code
...............................................31
I
Initial values
..............................................................26
Internet Fax Address
..................................................30
Internet Fax Function
.................................................37
L
[Layout] tab
...............................................................29
M
Message
...................................................................34
N
N/W-Fax driver options
...............................................29
O
Orientation
................................................................29
P
Preview
....................................................................33
Professional cover page
.............................................50
PWD
........................................................................15
R
Recipient’s Information
...............................................33
Reference Number
.....................................................33
Remove
....................................................................30
Removing recipients
...................................................24
Resolution
.................................................................30
Restore Defaults
...........................................32
S
Save as File
....................................................... 31
[Send] tab
................................................................ 30
Sender Information
.................................................... 34
Server Name
...................................................... 31
Server Name List
...................................................... 37
SNMP Settings
................................................... 31
SNMP V1/V2
............................................................ 35
SNMP V3
................................................................. 35
Specifying recipients
................................................. 14
Standard cover page
................................................. 48
SUB
......................................................................... 15
SUB/PWD
................................................................ 30
Subject
.................................................................... 34
T
To (recipient)
............................................................ 30
U
Update Automatically
................................................. 36
Update Now
............................................................. 37
User Authentication
................................................... 36
V
Version
N/W-Fax driver
...................................................... 37
SNMP
................................................................... 34
INDEX 51
52 INDEX
FC-5540C/6540C/6550C
FC-2040C/2540C/3040C/3540C/4540C
DP-2095/2530/3020/3590/4590/5010
DP-5560/6560/7560/8560
FC-2050C/2550C
FC-2051C/2551C
FC-2555C/3055C/3555C/4555C/5055C
FC-287CS/347CS/407CS
DP-4710S/5210S
DP-3030
FC-5560C/6560C/6570C
DP-2072/2572/3072/3572/4572/5072
DP-5570/6570/7570/8570
OME120022G0
MULTIFUNCTIONAL DIGITAL COLOR SYSTEMS /
MULTIFUNCTIONAL DIGITAL SYSTEMS
Network Fax Guide
1-11-1, OSAKI, SHINAGAWA-KU, TOKYO, 141-8562, JAPAN
©2012 - 2014 TOSHIBA TEC CORPORATION All rights reserved
R120120L0307-TTEC
Ver07 F 2014-03
Download
Public link updated
The public link to your chat has been updated.
Document public link
Advertisement
Key features
- Fax transmission using the N/W-Fax driver is available only when the optional Fax unit is installed.
- Send electronic documents from your PC to one or more destinations.
- Easy-to-use fax scheduler that allows you to set up a date and time to transmit your fax.
- Cover page options are also provided.
- You can easily maintain sender and contact information that can be printed on the cover pages.