Marquesas II Indoor/Outdoor 56" Ceiling Fan Owner`s

Hampton Bay®
International Collection
Marquesas II
Indoor/Outdoor
56" Ceiling Fan
Owner’s Manual
Marquesas II
Interior o Exterior
Ventilador de Techo de 56"
Manual del Propietario
Marquesas II by Hampton Bay
Hampton Bay Lifetime Limited Warranty
The retailer warrants the fan motor to be free from defects in workmanship and material
present at time of shipment from the factory for a lifetime after the date of purchase by the
original purchaser. The retailer also warrants that all other fan parts, excluding any glass or
plexiglass blades, to be free from defects in workmanship and material at the time of
shipment from the factory for a period of one year after the date of purchase by the original
purchaser. We agree to correct such defects without charge or at our option replace with a
comparable or superior model if the product is returned to the retailer. To obtain warranty
service, you must present a copy of the receipt as proof of purchase. All costs of removing
and reinstalling the product are your responsibility. Damage to any part such as by accident
or misuse or improper installation or by affixing any accessories, is not covered by this
warranty. Because of varying climatic conditions in the United States this warranty does
not cover any changes in brass finish, including rusting, pitting, corroding, tarnishing or
peeling. Brass finishes of this type give their longest useful life when protected from
varying weather conditions. A certain amount of wobble is normal and should not be
considered a defect. Servicing performed by unauthorized persons shall render the warranty
invalid. There is no other express warranty. The retailer hereby disclaims any and all
warranties, including but not limited to. Those of merchantability and fitness for a
particular purpose to the extent permitted by law. The duration of any implied warranty
which cannot be disclaimed is limited to the time period as specified in the express
warranty. Some states do not allow limitation on how long an implied warranty lasts, so the
above limitation may not apply to you. The retailer shall not be liable for incidental,
consequential, or special damages arising out of or in connection with product use or
performance except as may otherwise be accorded by law. Some states do not allow the
exclusion of incidental or consequential damages, so the above exclusion or limitation may
not apply to you. This warranty gives specific legal rights, and you may also have other
rights which vary from state to state. This warranty supersedes all prior warranties.
Date Purchased
Store Purchased
Model No.
640-660
Serial No.
Vendor No.
UPC
11289
792145351474
Lifetime Limited Warranty
Safety Rules.....................................................................................................................................
1.
Unpacking Your Fan ........................................................................................................................... 2.
Installing Your Fan ............................................................................................................................. 3.
Installing the Light Kit......................................................................................................................... 9.
Care of Your Fan ............................................................................................................................... 10.
Troubleshooting ................................................................................................................................ 11.
Specifications .................................................................................................................................. 12.
Table of Contents
1.To reduce the risk of electric shock, insure electricity has been
turned off at the circuit breaker or fuse box before beginning.
2. All wiring must be in accordance with the National Electrical
Code and local electrical codes. Electrical installation should be
performed by a qualified licensed electrician.
3. WARNING: To reduce the risk of electrical shock and fire, do not
use this fan with any solid-state fan speed control device.
4. WARNING: To reduce the risk of personal injury, use only the two
steel screws (and lock washers) provided with the outlet box for
mounting to the outlet box. Most outlet boxes commonly used for
the support of lighting fixtures are not acceptable for fan support
and may need to be replaced, consult a qualified electrician if in
doubt.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR PERSONAL
INJURY, MOUNT FAN TO OUTLET BOX MARKED ACCEPTABLE FOR
FAN SUPPORT.
5. The outlet box and support structure must be securely mounted
and capable of reliably supporting a minimum of 50 pounds. Use
only UL Listed outlet boxes marked FOR FAN SUPPORT.
6. WARNING: Use only with light kit marked "Suitable for Use in Wet
Locations"
7. The fan must be mounted with a minimum of 7 feet clearance
from the trailing edge of the blades to the floor.
8.
Do not operate the reverse switch while the fan blades are in
motion. The fan must be turned off and the blades stopped
before reversing the blades direction.
9.
Avoid placing objects in the path of the blades.
10. To avoid personal injury or damage to the fan and other items, be
cautious when working around or cleaning the fan.
11. Do not use water or detergents when cleaning the fan or fan
blades. A dry dust cloth or lightly dampened cloth will be
suitable for most cleaning.
12. After making electrical connections, spliced conductors should
be turned upward and pushed carefully up into the outlet box.
The wires should be spread apart with the grounded conductor
and the equipment-grounding conductor on one side of the outlet
box.
13. Electrical diagrams are for reference only. Light kits that are not
packed with the fan must be UL Listed and marked suitable for
use with the model fan you are installing. Switches must be UL
General Use Switches. Refer to the Instructions packaged with
the light kits and switches for proper assembly.
WARNING
TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE
BLADE ARMS (ALSO REFERRED TO AS BRACKETS) DURING ASSEMBLY
OR AFTER INSTALLATION. DO NOT INSERT OBJECTS IN THE PATH OF
THE BLADES.
NOTE
READ AND SAVE ALL INSTRUCTIONS!
1. Safety Rules
2
5
8
12
1
9
3
6
a
b
10
13
4
7
.
11
14
Unpack your fan and check the contents. You should have the following items;
1.
2.
3.
4.
5.
6.
Fan blades (5)
Canopy assembly
Ball/downrod assembly
Coupling cover
Fan motor assembly
Blade arms (5)
7.
8.
9.
10.
11.
12.
13.
Switch housing
Light kit
Decorative nut
Glass shade
40 Watt candelabra bulbs (3)
Pull chain and fobs (2)
14. Loose parts bag containing:
a. Blade attachment hardware
( 16 screws)
b. Mounting hardware
( 3 plastic wire connectors)
Balancing kit
WARNING
DO NOT INSTALL OR USE FAN
IF ANY PART IS DAMAGED OR MISSING.
CALL TOLL FREE 1-877-898-1881
Unpacking Your Fan 2.
Tools Required
Angled ceiling
maximum
18 angle
P h i l l i p s s c r e w d r i v e r, s t r a i g h t s l o t
screwdriver, adjustable wrench, step
ladder, and wire cutters.
Recessed
outlet box
Mounting Options
If there isn't an existing UL listed
mounting box, then read the following
instructions. Disconnect the power by
removing fuses or turning off circuit
breakers.
Mounting bracket
opening must be
toward the top
Outlet box
Figure 3
Figure 1
Note: You may need a longer downrod to
maintain proper blade clearance when
installing on a steep, sloped ceiling.
Secure the outlet box directly to the
building structure.
Use appropriate
fasteners and building materials. The
outlet box and its support must be able
to fully support the moving weight of the
fan (at least 50 lbs). Do not use plastic
outlet boxes.
Figures 1,2 and 3 are examples of
different ways to mount the outlet box.
Provide strong support
Outlet box
Figure 2
3. Installing Your Fan
Figure 4
Outlet box
To hang your fan where there is an existing
fixture but no ceiling joist, you may need
an installation hanger bar as shown in
Figure 4 (available at your Hampton Bay
Retailer).
Hanging the Fan
REMEMBER to turn off the power. Follow
the steps below to hang your fan properly:
CAUTION
REMOVE 5 RUBBER PACKING MOUNTS AND
DISCARD BEFORE INSTALLATION.
Step 1. Remove the decorative canopy
bottom cover from the canopy by turning
the cover counter clockwise.(Fig. 5)
Step 7. Align the holes at the bottom of the
downrod with the holes in the collar on top
of the motor housing (Fig.7). Carefully
insert the hanger pin through the holes in
the collar and downrod. Be careful not to
jam the pin against the wiring inside the
downrod. Insert the locking pin through the
hole near the end of the hanger pin until it
snaps into its locked position, as noted in
the circle inset of Fig. 7.
WARNING
FAILURE TO PROPERLY INSTALL LOCKING PIN AS
NOTED IN STEP 7 COULD RESULT IN FAN
LOOSENING AND POSSIBLY FALLING.
Step 2. Remove the hanger bracket from
the canopy by loosening the two screws
on the bottom of the hanging bracket a
half turn from the screw head and turning Step 8. Tighten two set screws on top of the
the canopy counter clockwise.(Fig, 5)
fan motor firmly (Figure 7)
Step 3. Pass the 120-volt supply wires Step 9. Place the downrod ball into the
through the center hole in the ceiling hanger bracket socket.
hanger bracket as shown in Fig. 6.
Step 4. Secure the hanger bracket to the
ceiling outlet box with the screws and
washers provided with your outlet box.
UL Listed
electrial
box
Hook
Figure 6
120V Wires
Mounting
screws
(supplied with
electrical box)
Motor wires
Ball/downrod
assembly
Downrod
Canopy
Canopy cover
Collar cover
Set screws
Hanger
bracket
Hanger pin
Step 5. Remove the hanger pin, lock pin
and set screws from the top of the motor
assembly.
Step 6. Route wires exiting from the top of
the fan motor through the collar cover,
canopy cover, canopy and then through
the ball / downrod. (Fig. 7)
Washers
Hanger
bracket
Ceiling
canopy
Figure 5
Canopy
cover
Locking pin
Figure 7
4.
Ground
Conductor
WHITE
SUPPLY CIRCUIT
BLACK
BLACK
WHITE
Ground
Conductor
Outlet Box
BLUE
WHITE
BLACK
WHITE
Green
Ground
Lead
Outlet Box
Light Switch
BLUE
BLACK
WHITE
GREEN
GREEN
Remember to disconnect the power.
Follow the steps below to connect the fan to your
household wiring.
Use the wire connecting nuts
supplied with your fan. Secure the connectors with
electrical tape. Make sure there are no loose strands or
connections.
Step 1 Connect the fan supply (black) wire and light
supply (blue) wire to the black household supply wire as
shown in Figure 8.
Step 2. Connect the neutral fan (white) wire to the white
neutral household wire.
Step 3 Connect the fan ground wire (green) to the
household ground wire.
Step 4 After connecting the wires, spread them apart so
that the green and white wires are on one side of the
outlet box and the black and the blue wires are on the
other side.
Step 5 Turn the connecting nuts upward and push the
wiring into the outlet box.
Figures 9 and 10 illustrate the wiring connections for
the optional wall control (available at your Hampton Bay
Retailer, the wire color out of the wall control may vary,
see wall control's installation manual for correct wire
SUPPLY CIRCUIT
BLUE
BLACK
WHITE
Making the Electrical
Connections
Ground to
Downrod
BLUE
WHITE
BLACK
WHITE
Green
Ground
Lead
Ground to
Downrod
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR OTHER
PERSONAL INJURY. MOUNT FAN ONLY ON AN OUTLET BOX OR
SUPPORTING SYSTEM MARKED ACCEPTABLE FOR FAN SUPPORT.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK. DO NOT USE THIS
FAN WITH ANY SOLID-STATE SPEED VARIABLE CONTROL DEVICE.
5.
Figure 8
Figure 9
Diagram indicates optional light kit wiring.
Diagram indicates optional light kit wiring.
BLACK
WHITE
SUPPLY CIRCUIT
Light
Ground
Conductor
Finishing the Installation
Outlet box
Step 1. Tuck connections neatly into ceiling
outlet box.
BLUE
BLACK
WHITE
GREEN
Outlet Box
Fan
BLUE
WHITE
BLACK
WHITE
Green
Ground
Lead
Ground to
Downrod
Step 2. Slide the canopy up to ceiling and
over the 2 screws on the hanger bracket.
Rotate canopy clockwise. Next, while
holding the canopy with one hand, slide the
canopy cover over the screws and rotate
clockwise until tight. Note: adjust the
canopy screws as necessary until the canopy
and canopy cover are snug. (Fig. 11)
Hanger
bracket
Screws
Canopy
Canopy
cover
Figure 11
WARNING
Make sure the notch on the hanging
bracket properly sits in the groove in
the hanger ball before attaching the
canopy to the bracket by turning the
housing until it drops into place.
Figure 10
Diagram indicates optional light kit wiring.
6.
Attaching the Fan
Blades
Step 1 Attach blades to blade arms using
three screws and rubber washers as shown
in Figure 12. Start a screw into the arm, do
not tighten. Repeat for the 2 remaining
screws and washers.
Screws
Rubber
washer
Step 4 Install an optional light kit if you
wish. Follow the instructions included with
the kit.
7.
1. Check that all blade and blade bracket
screws are secure.
Blade
arm
Figure 12
Step 2 Tighten each screw securely starting
with the center screw. Make sure the blade
is straight.
Step 3 Fasten the blade arms to the motor
by inserting the tab from the blade arms to
the slot in the bottom motor housing, then
tighten the two screws and washers already
installed in the blade arms (Figure 13).
The following procedure should correct
most fan wobbling problems. Check after
each step.
Blade
Motor
Slot
Tab
Blade arm
2. Most fan wobbling problems are
caused when blade levels are unequal.
Check this level by selecting a point on
the ceiling above the tip of one of the
blades. Measure this distance as shown
in Figure 14. Rotate the fan until the
next blade is positioned for
measurement. Repeat for each blade.
The distance deviation should be equal
within 1/8".
3. Use the enclosed Blade Balancing Kit
if the blade wobble is still noticeable.
Figure 13
4. If the blade wobble is still noticeable,
interchanging two adjacent (side by side)
blades can redistribute the weight and
possibly result in smoother operation.
WARNING
TO REDUCE THE RISK OF PERSONAL INJURY,
DO NOT BEND THE BLADE HOLDERS
WHILE INSTALLING, BALANCING THE
BLADES, OR CLEANING THE FAN. DO NOT
INSERT FOREIGN OBJECTS BETWEEN ROTATING
FAN BLADES.
Touching
ceiling
Figure 14
Installing the Switch
Housing
Step 1. Remove the 1 of 3 screws from the
mounting ring and loosen the other 2
screws. (Do not remove)
Step 2. Place the key holes on the switch
housing over the 2 screws previously
loosened from the mounting ring, turn
switch housing until it locks in place at the
narrow section of the key holes. Secure by
tightening the 2 screws previously
loosened and the one previously removed.
(Fig. 15)
Mounting ring
Switch housing
Screws
Figure 15
8.
NOTE: Before starting installation,
disconnect the power by turning off the
circuit breaker or removing the fuse at fuse
box.
1.Remove the 1 of 3 screws from the switch
housing and loosen the other 2 screws.
(Do not remove)
NOTE: Light bulbs have no warranty,
can be purchased at local light bulb
specialty store or from our service
center.
2. Raise and hold the light kit close to the
switch housing and proceed to do the
wire connections. Connect the white wire
connectors from the light kit and fan,
follow the same procedure with the black
and blue wire connectors. (Fig. 16)
3. Carefully push all wires back into the
switch housing, Place the key holes on
the light kit over the 2 screws previously
loosened from the switch housing, turn
light kit until it locks in place at the
narrow section of the key holes. Secure
by tightening the 2 screws previously
loosened and the one previously removed.
Be sure to tighten all screws. (Fig. 16)
4. Pass the two pull chains on the switch
housing through the chain holders
located on the switch housing, install the
fobs to the pull chains. (Fig. 17)
Chains
holders
Light kit
40W bulbs
Switch
housing
Screws
5. Install 3x40W (MAX.) bulbs (provided).
6. Place the glass shade over the light kit
and secure it with the decorative nut. Do
not over tighten.(Fig. 17)
Connection plug
Glass shade
Light kit
Figure 16
7. Restore and your light kit is ready for
operation.
9. Installing the Light Kit
Decorative nut
Figure 17
Pull
chains
Here are some suggestions to help you
maintain your fan
1. Because of the fan's natural movement,
some connections may become loose.
Check the support connections,
brackets, and blade attachments twice
a year. Make sure they are secure. (It
is not necessary to remove fan from
ceiling.)
NOTE
WAIT FOR FAN TO STOP BEFORE
CHANGING THE SETTING OF THE SLIDE
SWITCH.
Turn on the power and check the operation of
your fan. There are two pull chains available in
your fan:
1. 3-speed pull chain- it controls the fan speed
as follows: 1 pull- High, 2 pulls- Medium, 3
pulls- Low, and 4 pulls- Off.
Speed settings for warm or cool weather
depend on factors such as the room size,
ceiling height, number of fans, and so on.
2. Light kit pull chain- it controls the light kit
in "ON" or "OFF".
The slide switch controls directions: forward
(switch left ) or reverse (switch right ).
Warm weather - (Forward) A downward air
flow creates a cooling effect as shown in
Figure 18. This allows you to set your air
conditioner on a higher setting without
affecting your comfort.
Cool weather - (Reverse) An upward airflow
moves warm air off the ceiling area as shown
in Figure 19. This allows you to set your
heating unit on a lower setting without
affecting your comfort.
Figure 18
2. Clean your fan periodically to help
maintain its new appearance over the
years. Use only a soft brush or lint-free
cloth to avoid scratching the finish. The
plating is sealed with a lacquer to
minimize discoloration or tarnishing.
Do not use water when cleaning. This
could damage the motor, or the wood, or
possibly cause an electrical shock.
3. There is no need to oil your fan. The
motor has permanently lubricated
bearings.
Figure 19
IMPORTANT
MAKE SURE THE POWER IS OFF AT THE
ELECTRICAL PANEL BOX BEFORE YOU
ATTEMPT ANY REPAIRS. REFER TO THE
SECTION "MAKING ELECTRICAL
CONNECTIONS"
Care of Your Fan 10.
Problem
Solution
Fan will not start.
1.Check circuit fuses or breakers.
2. Check line wire connections to the fan and switch wire connections in the switch housing.
CAUTION: Make sure main power is off.
Fan sounds noisy.
1. Make sure all motor housing screws are snug.
2. Make sure the screws that attach the fan blade bracket to the motor hub is tight.
3. Make sure wire nut connections are not rubbing against each other or the interior wall of the switch
housing.
CAUTION: Make sure main power is off.
4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappear during this
time.
5. If using an optional light kit, make sure the screws securing the glassware are tight. Check that light
bulb is also secure.
6.Some fan motors are sensitive to signals from solid-state variable speed controls.
If you have installed this type of control, choose and install another type of control.
7. Make sure the upper canopy is a short distance from the ceiling. It should not touch the ceiling.
11. Troubleshooting
Download PDF

advertising