Operating and Installation Instructions Refrigerator

Operating and Installation Instructions
Refrigerator
To prevent accidents and appliance damage read these instructions
before installation or use.
en - US, CA
M.-Nr. 09 920 730
Contents
IMPORTANT SAFETY INSTRUCTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Guide to the refrigerator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Turning the appliance On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Turning the button sound On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Turning off for longer periods of time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Temperature and door alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Temperature alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Door alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Setting the temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Setting the temperature in the refrigerator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
SmartFresh drawers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Storage temperatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Using the SmartFresh drawers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Using the refrigerator efficiently . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
SuperCool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Automatic defrost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Adjusting the interior fittings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Moving the shelves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Removing the storage shelf from above the deli drawer . . . . . . . . . . . . . . . . . . . . 23
To remove the shelf above the SmartFresh drawers . . . . . . . . . . . . . . . . . . . . . . . 23
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Cleaning the interior and accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Appliance doors / Side walls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Humidity filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Ventilation slits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Door seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Changing the light bulb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Causes of noises . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
2
Contents
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Climate Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Stainless steel panels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Installation options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Adjusting the door opening angle (optional accessory) . . . . . . . . . . . . . . . . . . . . 43
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Niche dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Installing the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Before you begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
RemoteVision module installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Preparing the installation niche . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Sliding the appliance into the installation space . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Aligning the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Attaching the appliance to the installation niche . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
RemoteVision (optional accessory) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Contact details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
3
IMPORTANT SAFETY INSTRUCTIONS
When using the appliance, follow
basic safety precautions, including
the following:
Read all instructions before
installation and use to prevent
accidents and machine damage.
This appliance is intended for
residential use only. Use only as
described in this Operating manual.
Only use the appliance for its
intended purpose.
This appliance complies with current
safety requirements. Improper use
of the appliance can lead to
personal injury and material
damage.
Keep these operating instructions in
a safe place and pass them on to
any future user.
Electrical Safety
~ Before installation, make sure that
the voltage and frequency listed on the
data plate correspond with the
household electrical supply. This data
must correspond to prevent injury and
machine damage. Consult a qualified
electrician if in doubt.
~ Before installation or service,
disconnect the power supply to the
work area by unplugging the unit,
"tripping" the circuit breaker or
removing the fuse.
~ Do not use an extension cord to
connect this appliance to electricity.
Extension cords do not guarantee the
required safety of the appliance
(e.g., danger of overheating).
~ Be certain your appliance is
properly installed and grounded by a
qualified technician. To guarantee the
electrical safety of this appliance
continuity must exist between the
appliance and an effective grounding
system. It is imperative that this basic
safety requirement be met. If there is
any doubt, have the electrical system of
the house checked by a qualified
electrician.
~ Only connect power to the
appliance when all installation work is
complete.
4
IMPORTANT SAFETY INSTRUCTIONS
Installation
This appliance is top-heavy and
must be secured to prevent the
possibility of tipping forward.
Keep the door closed until the
appliance is completely installed
and secured per the installation
instructions.
~ This appliance must be installed
and connected in compliance with the
installation instructions.
~ Installation and repair work should
be performed by a Miele authorized
service technician. Work by unqualified
persons could be dangerous and may
void the warranty.
~ Installation must comply with local
regulations and state laws.
Use
~ This appliance is not designed for
commercial use. It is intended for use in
domestic households and in similar
working and residential environments
such as:
– shops, offices and similar work
environments
– by customers in hotels, motels, Bed
& Breakfasts or similar residential
environments.
~ This appliance is not intended for
outdoor use.
~ Persons who lack physical, sensory
or mental abilities, or experience with
the machine should not use it without
supervision or instruction by a
responsible person.
To reduce the risk of injury, do not
~ Do not operate any appliance with a ~
allow children to play in, on or near the
damaged cord or plug, or if the
appliance has been damaged in any
manner. Contact Miele’s Technical Service Department.
~ This appliance must not be used in
a non-stationary location (e.g. on a
ship).
~ Do not install the refrigerator in a
room with too low an ambient
temperature, e.g., a garage, as this
may lead to the appliance switching off
for longer periods so that it cannot
maintain the required temperature.
appliance, especially in the door hinge
area.
~ After your refrigerator is in operation,
do not touch the cold surfaces in the
refrigerator compartment, particularly
when hands are damp or wet. Skin may
adhere to these extremely cold
surfaces.
~ Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
~ Do not use any oils or grease on the
door seal, as these will cause the seal
to deteriorate and become porous with
time.
5
IMPORTANT SAFETY INSTRUCTIONS
~ Do not block the ventilation gaps in
the plinth or the top of the appliance
housing unit, as this can impair the
efficiency of the appliance, increase the
electricity consumption and cause
damage to the appliance.
~ Never use a steam cleaner to clean
the appliance. Pressurized steam could
damage electrical components and
cause a short circuit.
The following applies to
stainless steel appliances:
Disposal of your old appliance
~ Before disposing of an old
appliance, first make the door latch or
lock unusable.
~ Take off the door.
~ Leave the shelves in place so that
children may not easily climb inside.
~ Consult with your municipal policy
on recycling.
~ Be careful not to damage any part of
adhesive tape, masking tape or other
types of adhesive on the coated
surface of the appliance door. These
will damage the surface, causing it to
lose its soil resistant protective coating.
the pipework while awaiting disposal
by:
puncturing the refrigerant
channels in the evaporator.
bending any pipework.
scratching the surface coating.
Splashes of refrigerant can damage the
eyes.
~ The high-quality surface coating of
~ Your old refrigerator may have a
~ Do not use sticky notes, transparent
the appliance door is susceptible to
scratches. Even a magnet can cause
damage.
cooling system that used CFCs
(chlorofluorocarbons). CFCs are believed
to harm stratospheric ozone.
If you intentionally release this CFC
refrigerant, you can be subject to fines
and imprisonment under provisions of
environmental legislation. Make sure the
CFC refrigerant is removed and disposed
of by a qualified technician.
SAVE THESE
INSTRUCTIONS
6
Guide to the refrigerator
a Hinged door shelf
b Shelves (height adjustable)
c Door shelves (height adjustable)
d Deli drawer
e Control panel
f Main switch
g Humidity filters
h SmartFresh drawers
7
Guide to the refrigerator
Control panel
a Access button "p"
activates the control panel
b Refrigerator
c Upper SmartFresh drawer
d Lower SmartFresh drawer
e Temperature display
X colder; Y warmer
Allows you to set the desired
temperature in the refrigerator
f Food type(s) to be stored in the
SmartFresh drawers
(left: high humidity
right: lower humidity)
g On/Off sensor button for the
SuperCool function
h Sensor button for the temperature
and door alarm*
* Only visible when the relevant
function is activated
8
Before use
Before using for the first time
Turning the appliance On/Off
The stainless steel surface of the
appliance is protected with a plastic
film, which protects it during shipping.
^ Open the appliance door.
Do not remove this protective film until
the appliance has been completely
installed.
After removing the protective film clean
the exterior surface with the supplied
stainless steel agent. This will aid in
preventing resoiling.
^ Clean the inside of the appliance and
the accessories with a mild solution
of warm water and liquid dish soap.
Dry with a soft cloth.
If the appliance was transported or
laid horizontally for any reason,
allow it to stand vertical for at least 8
hours before turning it on. Failure to
do so will affect the functioning of
the appliance.
^ Turn the appliance On/Off with the
main switch.
The main switch is located on the
right-side underneath the control panel.
All zones are switched on or off
together.
Once on, the appliance begins cooling.
When the door is open, the interior
lights come on.
The access button will light in the
control panel.
The preset temperatures (factory
settings) are reached after a few
hours. Do not put any food in the
appliance until the preset
temperatures are reached.
,Switching the appliance off with
the main switch does not safely
isolate it from the power supply.
9
Settings
Using the settings
This appliance is operated with the use
of touch keys activated by a finger.
Depending on the zone selected, you
can now:
– adjust the temperature,
– An available button will appear white.
– select the SuperCool function or
– A selected button will appear yellow.
– select settings for the SmartFresh
drawers by food type.
For additional information, see the
corresponding sections in the manual.
^ Touch the access button "p" so it
turns yellow.
On the control panel you will now see
the sensor buttons for the three
appliance zones.
^ To change settings (e.g., to set the
temperature, etc.), touch the sensor
button for the appliance zone you
wish to set.
The selected sensor button appears
yellow and depending on the zone
selected, additional sensor buttons will
appear on the control panel.
10
^ To de-select a zone touch the sensor
button for that particular zone so that
it turns white or select another sensor
button.
^ To leave the settings menu, touch the
access button "p" so it turns white.
The last settings entered are stored.
If the access button is not pressed
the display will go out after approx.
30 secs.
The sensor buttons for the three
appliance zones now disappear from
the control panel.
Settings
Custom settings
In the custom settings mode you can
select and change functions. The
function possibilities are described in
the respective chapters of this manual.
Function
†
RemoteVision
Module settings
(optional accessory)
;
To enter and exit the
Settings mode
If you prefer the buttons to be silent
when touched the button sound can be
turned off.
Display text
Temperature unit
°C - °F
(see "Setting the
temperature")
Button sound on/off
(see "Settings")
Turning the button sound
On/Off
^ Touch the access button "p" so it
turns yellow.
=
^ Touch the sensor button for the
refrigerator so it turns yellow.
c
^ Note the position of the X button, but
do not touch.
^ Touch the access button "p" again so
it turns white.
Only the access button "p" is visible.
^ Place one finger on the position of
the X button and hold (the X button
will not be visible).
^ While holding down the X button,
press the access button "p" once.
Keep holding the X button down until
the following appears in the display
(approx. 5 seconds).
^ Tap the X button until = appears in
the display.
^ Touch the access button "p" to
confirm.
11
Settings
^ By touching the X button, you can
choose between:
= 0 : Button sound is off
= 1 : Button sound is on
= – : Return to menu.
^ Touch the access button "p" to
confirm the setting.
^ Tap the X button until you see ; in
the display.
Turning off for longer periods
of time
If the appliance is not going to be used
for an extended time (for example,
during a vacation) some precautions
should be taken.
^ Take all food out of the appliance
^ Turn the appliance off at the main
switch
^ Unplug the appliance
^ Clean the interior
^ Touch the access button "p".
You have now left the Custom settings
mode.
When you are in the Custom settings
mode the door alarm is turned off
automatically. Once the door is
closed it is reactivated.
12
^ Leave the door open to prevent
odors
Temperature and door alarm
The appliance is equipped with an
alarm system, to ensure that the
temperature does not rise unnoticed
because of energy loss or an open
door.
The alarm system is always
operational, it does not need to be
switched on.
Temperature alarm
If the temperature becomes too warm,
an alarm sounds, the "alarm" indicator
turns red and flashes. At the same time
the affected zone flashes in the display.
The alarm will sound and the display
will flash if:
– too much warm air flows into the
appliance, for example when food is
being loaded, re-arranged, or taken
out.
– large amounts of food are loaded at
once.
– the power fails.
Turning the temperature alarm Off
As soon as the alarm condition is
corrected, the alarm signal turns off
and the affected zone stops flashing in
the display. The "alarm" indicator goes
out.
^ To turn the alarm off early, press
the "alarm" sensor button.
The alarm signal turns off. The "alarm"
indicator remains red and the
corresponding appliance zone
continues to flash until the alarm
condition is corrected.
Door alarm
If the appliance door is left open, an
alarm signal will sound and the "alarm"
indicator will turn red after five minutes.
Turning the door alarm Off
Once the door is closed the alarm turns
off and the "alarm" indicator goes out. If
the door has not been closed properly,
the alarm will sound again after five
minutes.
^ To turn the alarm off early, press
the "alarm" sensor button. The "alarm"
indicator and signal will turn off.
13
Setting the temperature
Setting the temperature in the
refrigerator
The loss of coldness is no cause for
concern if it is due to the door being left
open for a while, e.g. for removing or
storing a large amount of food.
Temperature range
^ Touch the access button "p" so it
turns yellow.
The temperature can be selected within
the following ranges:
– Refrigerator :
35 to 46° F (2°C to 8°C)
^ Touch the sensor button for the
refrigerator so it turns yellow.
^ Use the X and Y buttons next to the
temperature display to set the
temperature warmer or colder.
Tap the X and Y sensor buttons to
raise/lower the temperature 1°, or hold
it down to move through the
temperature range more quickly.
Temperature display
The temperature display on the
operating panel always shows the
required temperature.
The display will flash if:
– a different temperature is being set,
– the temperature in the appliance has
risen by several degrees, indicating
that the appliance is warming up too
much.
14
A temperature of 37°F (4°C) in the
refrigerator section is recommended.
The room temperature and the
installation location can affect the time it
takes for the appliance to get to the
desired temperature. If the room
temperature is too high, it may not be
possible for the appliance to reach the
lowest temperature.
Setting the temperature
Temperature unit
(Fahrenheit/Celsius)
The temperature can be displayed in
degrees Fahrenheit (°F) or Celsius (°C).
^ Touch the access button "p" so it
turns yellow.
^ While holding down the X button,
press the access button "p" once.
Keep holding the X button down until
the following appears in the display
(approx. 5 seconds).
^ Tap the X button until † appears in
the display.
^ Touch the access button "p" to
confirm.
^ Touch the sensor button for the
refrigerator section so it turns yellow.
^ Note the position of the X button, but
do not touch.
^ By touching the X button you can
select either Fahrenheit or Celsius for
the temperature display.
† 0: Fahrenheit
† 1: Celsius
† –: return to menu
^ Touch the access button "p" again so
it turns white.
^ Touch the access button "p" to
confirm the setting.
Only the access button "p" is visible.
^ Tap the X button until a ; appears in
the display.
^ Place one finger on the position of
the X button and hold (the X button
will not be visible).
^ Touch the access button "p".
You have left the Custom settings
mode.
When you are in the Custom settings
mode the door alarm is turned off
automatically. Once the door is
closed it is reactivated.
15
SmartFresh drawers
The SmartFresh drawers provide the
right combination of temperature and
humidity. The result is freshness up to
three times longer than in the other
zones of the refrigerator.
Storage temperatures
For fresh foods that are not adversely
affected by cold, the best range is
32° - 37°F (0° - 3°C). This helps to keep
the food fresh considerably longer than
in the rest of the refrigerator, spoiling is
minimal.
The temperature is set to approx. 35°F
(1.5°C).
Humidity
The closer the humidity in the appliance
matches the moisture content of the
food, the more moisture the food will
retain, and the fresher and crisper it will
stay over a longer period of time.
The optimal humidity is determined on
the basis of the food stored in the
appliance.
Proper humidity is assisted by 2
humidity filters located above the
SmartFresh drawers. These filters allow
air to pass through, yet retain moisture.
Using the SmartFresh drawers
^ Use the sensor button to select the
desired drawer.
The selected sensor button turns
yellow, and the sensor buttons for the
food choices appear.
The most recently selected food type(s)
appear yellow.
^ Use the sensor buttons to select the
food type(s).
– Several food types can be selected
at the same time.
– To delete a food type, simply press it
again.
– Depending on the food types
selected, the optimal humidity is
determined for the SmartFresh
drawers.
– The "deli" and "dairy" settings are the
most energy efficient.
^ Touch the access button to confirm
the settings.
^ Place the food in the drawer.
^ Repeat the process above to
additional food types.
16
SmartFresh drawers
Tips for storing food in the
SmartFresh drawers
For optimal storage conditions, it is
always best to store similar foods
together in one drawer.
The upper SmartFresh drawer is the
best place to store moisture
sensitive foods.
Be sure the drawers are clean and
dry before placing food in them.
Foods that are best stored under dry
conditions
– fresh fish and shellfish, meats,
poultry, sausage, dairy products and
deli salads.
Foods that are best stored under
moist conditions
– fresh produce, e.g., vegetables,
lettuce, herbs, mushrooms,
cabbage, fruit.
Remember that higher moisture levels
can only be attained when the food is
stored unpacked so air can circulate
freely.
17
Using the refrigerator efficiently
Different storage zones
Coldest area
Due to the natural circulation of air in
the appliance, there are different
temperature zones in the refrigerator.
Cold, heavy air sinks to the lowest
section of the appliance. Make use of
these different zones when placing
food in the appliance.
The coldest area in the refrigerator is
directly above the SmartFresh drawers.
The temperature in the drawers
themselves is even colder.
Use these cold areas in the refrigerator
for all highly perishable foods, such as:
– fish, meat, poultry,
This appliance uses a dynamic
cooling feature to establish a
constant temperature during
cooling. As a result, the differences
between temperature zones are less
pronounced.
Leave some space between items, so
air can circulate freely around them.
Make sure the ventilation slits are not
covered - this is important for the
cooling performance.
Warmest area
The warmest area is in the top section
of the door. Use this area to store items
such as butter and cheese.
– deli meats, store-bought meals,
– dishes or baked goods containing
eggs or cream,
– fresh bread dough, pastry dough,
cake batters,
– dairy products.
If storing high-proof alcohol, make
sure it is tightly closed and stored
upright.
Do not store cooking oil in the
refrigerator door. Traces of oil can
cause stress cracks to occur in the
plastic components in the door.
Do not allow food to touch the rear
wall of the appliance, it may freeze
to the wall.
18
SuperCool
When the SuperCool function is
activated, the appliance is cooled as
cold and quickly as possible (to a
factory-preset temperature).
The SuperCool function is ideal for the
rapid cooling of drinks and for
refrigerating large quantities of foods.
Switching on SuperCool
^ Touch the sensor button for the
refrigerator so it turns yellow.
^ Touch the SuperCool sensor button
so it turns yellow.
In the temperature display for the
refrigerator zone, the new temperature
setting appears, 35°F (2°C).
Switching off SuperCool
The SuperCool function automatically
switches off after approx. 6 hours. The
sensor button turns white, and the
appliance continues running at normal
power.
To save energy, the SuperCool function
can be switched off early, once the
food and/or drinks are sufficiently
chilled.
^ Touch the SuperCool sensor button
so that it turns white.
The temperature display for the zone
selected returns to the original
temperature setting.
The appliance now continues running
at normal power.
The temperature in the appliance now
begins to fall, with maximum cooling in
the refrigerator zone.
19
Automatic defrost
Refrigerator and SmartFresh
drawers
The refrigerator and SmartFresh
drawers defrost automatically.
During normal operation, condensate
and frost can form on the rear wall of
the refrigerator and drawers.
You do not need to remove this
build-up, it will defrost and evaporate
automatically with the heat generated
by the appliance.
20
Adjusting the interior fittings
Moving the shelves
Deli drawer
The shelves can be adjusted according
to the height of the food.
This drawer is set on telescopic tracks.
It can be pulled in and out for loading
and unloading, or removed for
cleaning.
^ Using both hands, grasp the shelf
from underneath and lift slightly so
that the rear of the shelf is slightly
above the mountings.
^ Open the drawer.
^ Pull the shelf forward.
^ Move the shelf to the desired height,
then insert the (rear) hooks into
place.
^ Make sure the shelf is level.
^ On both sides of the drawer, pull the
latches (see arrow) upward and lift
the drawer out of the refrigerator.
Push the tracks back into the
refrigerator to avoid injury.
Replacing the drawer
^ Completely extend the telescopic
tracks.
^ Lay the drawer onto the tracks so that
it connects in the front and back.
^ Slide the drawer in.
21
Adjusting the interior fittings
SmartFresh drawer
Replacing the drawer
These drawers are set on telescopic
tracks. They can be pulled in and out
for loading and unloading, or removed
for cleaning.
^ Completely extend the telescopic
tracks.
^ Lay the drawer onto the tracks so that
it connects in the front and back.
^ Turn the safety lock back to the
vertical position.
^ Slide the drawer in.
^ Open the drawer.
On the hinged side of the door is a
safety lock, which must be turned to a
horizontal position before the drawer
can be removed.
^ Using a suitable object, e.g., coin,
turn the safety lock to a horizontal
position a.
^ On both sides of the drawer, pull the
latches b upward and lift the drawer
out of the refrigerator.
Push the tracks back into the
refrigerator to avoid injury.
22
Adjusting the interior fittings
Adjusting the door shelves
Removing a door shelf
For easier loading, unloading, and
cleaning, the door shelves can be
shifted or completely removed.
^ Slide it upward all the way to the top
of the slide-rails, until it can be
removed.
Replacing a door shelf
^ Start at the top of the slide-rails and
slide the shelf down into the desired
position.
Removing the hinged door shelf
^ Pull the stops upward and out of the
shelf, and remove the shelf lid
upward.
^ Now remove the hinged container
upward and out.
Removing the storage shelf
from above the deli drawer
^ Using both hands, grasp the door
shelf by the frame and tip it slightly
forward.
^ Lift the shelf up and out.
^ Slide the tipped shelf up or down
along the slide-rails, and click it into
place with the lower hooks.
^ When replacing the shelf, make sure
that the lugs on the corners at the
back are correctly engaged.
^ Make sure the shelf is level.
To remove the shelf above the
SmartFresh drawers
^ Remove the deli drawer.
^ Remove the filler strip at the back,
push back the glass shelf slightly,
then lift it carefully up and out.
^ Replace the deli drawer.
23
Cleaning and care
To reduce the risk of electrical
shock, disconnect the appliance
from the power supply by shutting
off the power main, tripping the
circuit breaker or unplugging the
power cord before maintenance.
Never use cleaning agents
containing abrasive substances
such as sand, soda, acids,
chlorides or chemical solvents.
Non-abrasive cleaning agents are
also unsuitable, as they can cause
matte areas to appear.
To better maintain your appliance
avoid the following:
– cleaners containing soda, ammonia,
thinners, or chlorides
– solvent based cleaning agents
– stainless steel cleaners
– cleaners containing descaling
agents or lime removers,
– abrasive cleaners,
– dishwasher soap (powder),
– caustic (oven) cleaners,
– scouring pads, steel wool, hard
brushes,
Stainless steel surfaces can be
cleaned using a non-abrasive
stainless steel cleaner (available
from Miele).
– glass cleaners,
Only use a mild solution of warm
water and liquid dish soap to clean
this appliance.
– steam cleaning products.
Do not use a steam cleaner to clean
this appliance. Pressurized steam
could penetrate electrical
components and cause a short
circuit.
Do not allow water to get into the
electronic unit or lights.
The data plate located inside the
appliance must not be removed. It
contains information which is
required in the event of a service
call.
24
– metal scrapers,
– eraser sponges,
Glass cleaners may be used to
clean the exterior. However do not
allow them to sit or "puddle", this can
cause damage to the surface.
Remove the cleaner promptly.
Cleaning and care
The stainless steel doors have a
special coating that is soil-resistant.
Do not wipe these with a stainless
steel conditioner, it will leave visible
streaks.
Use a stainless steel conditioner to
clean and maintain the stainless
steel surfaces of the appliance. It
contains material-friendly
substances and - unlike stainless
steel cleaning agents - no polishing
substances.
This gently removes soiling and
each application forms a protective
layer that is stain- and
water-repellent.
Before cleaning
^ Use the main switch to turn the
appliance off completely.
The main switch is located on the
right-side underneath the control panel.
^ Unplug the power cord.
^ Remove any food from the appliance
and store it in a cool place.
^ Take out any removable parts,
e.g., shelves, drawers.
Cleaning the interior and
accessories
Use a mild solution of warm water and
liquid dish soap. Wash all accessories
and drawers by hand. Do not wash in a
dishwasher.
^ Clean the appliance as needed.
^ After washing, wipe down the interior
and accessories with a clean wet
cloth, then dry with a soft cloth.
Leave the appliance door open for a
short time, so the moisture can
evaporate.
Appliance doors
Remove soiling on the appliance
doors and side walls right away. If
soiling is left on, it may become
diffficult to remove and the surfaces
may discolor.
All surfaces are susceptible to
scratches. All surfaces may become
discolored when they come into
contact with unsuitable cleaning
materials.
^ Clean the surface with a soft sponge,
liquid dish soap and warm water. A
clean, damp microfiber cloth may
also be used, without a cleaning
agent.
^ After cleaning, rinse everything with
clean water, then dry with a soft
cloth.
25
Cleaning and care
Additional instructions for stainless
steel appliances:
– Appliance doors
The appliance doors are finished with a
high-quality surface coating. It protects
them from soiling and makes cleaning
easier.
Do not treat appliance doors with
stainless steel cleaning agents:
This will damage the coating!
Aluminum frames
The shelf frames are made of
aluminum.
^ Clean the frames with a mild solution
of warm water and liquid dish soap.
Aluminum is susceptible to
scratches and nicks, treat with care.
The aluminum frames may become
discolored or otherwise altered if
soiling is not cleaned away
promptly.
Do not use stainless steel cleaners;
lime removers; scouring pads, such
as pot scrubbers; or used sponges
that still contain abrasive cleanser
residue to clean the frames.
26
Cleaning and care
Humidity filters
The two humidity filters, located above
the SmartFresh drawers, must be
removed for cleaning.
^ Remove the filter mat.
^ Remove the SmartFresh drawer.
^ Clean the filters by rinsing them with
lukewarm water.
Do not clean in a dishwasher or
washing machine. This will damage
the filter.
^ Air-dry the filters.
^ Place the filters back in the filter
cover.
^ Unhook the filter cover a in each
side of the drawer and remove them
along with the filters downwards
starting from b.
^ Put the filter cover back in place,
inserting the rear hooks first.
^ Re-insert the SmartFresh drawer.
27
Cleaning and care
Ventilation slits
After cleaning
^ Check the ventilation slits in the base
panel regularly. Remove any dirt/dust
with a vacuum cleaner or brush.
Clean as needed.
^ Return all shelves and accessories.
^ Place food back in the refrigerator
and drawers.
^ Close the appliance door.
Door seals
Do not use oil or grease on the door
seals. This may cause the seals to
deteriorate and become porous over
time.
^ Clean the door seals with water and
dry thoroughly.
28
^ Insert the plug in the socket and
switch the appliance on.
Cleaning and care
Changing the light bulb
The lighting automatically switches off
after the door has been open for
approx. 5 minutes. This is not a fault.
Never touch a halogen bulb with
bare fingers.
When inserting a glass halogen
bulb, always hold with a soft cloth.
After the bulb has cooled for a short
time it will turn on again.
If the light does not come on when the
door is opened briefly, the light bulb
should be changed.
^ Use the main switch to turn the
appliance off.
To reduce the risk of electric shock,
disconnect the appliance from the
power supply by unplugging or tripping
the circuit breaker.
Upper lighting
^ Remove the defective light bulb.
^ Place the new bulb in the socket.
Halogen bulb type:
20 W/12 V/socket GY 6.35.
^ Slip the rear of the light cover back
into position, then pull it forward and
into place.
^ Grasp the front of the light cover with
both hands, and slide it back.
^ Carefully pull the cover forward and
out.
29
Cleaning and care
Side lighting
^ Turn the light cover counterclockwise
and pull out.
Never touch a halogen bulb with
bare fingers.
When inserting a glass halogen
bulb, always hold with a soft cloth.
^ Pull the defective light bulb from the
socket.
^ Place the new bulb in the socket.
Halogen bulb type:
5 W/12 V/socket G 4.
^ Put the light cover back on and turn
clockwise into place.
^ Restore power to the appliance.
30
Frequently asked questions
With the aid of the following guide minor problems can be corrected without a service call.
Repairs should only be carried out by a qualified and trained person in strict
accordance with local and national safety regulations. Unauthorized repairs
could cause personal injury or machine damage and may void the warranty.
Issue
Possible fault
The refrigerator does The machine is not
not get cold.
turned on.
Solution
Check whether the appliance
is switched on at the main
switch. The temperature
display must be lit up.
The machine is not
plugged in.
Check that the plug is
correctly inserted in the power
outlet.
Check that the fuse has
not tripped.
Reset the circuit breaker.
If the breaker trips again the
appliance or the outlet may be
defective. Contact Miele or a
qualified electrician.
The temperature is set
incorrectly.
Check the display.
Issue
Possible fault
Solution
The temperature in
the refrigerator is
too low.
Select a warmer
temperature.
See "Selecting the correct
temperature".
The SuperCool function
is still on.
If, nessary turn off the
SuperCool function.
The door is not closed.
Check that the door has been
closed properly.
A large amount of food is This makes the compressor
put in the refrigerator at run longer, causing the
the same time.
temperature to fall
automatically.
31
Frequently asked questions
Issue
Possible fault
Solution
The compressor kicks
on very frequently and
for too long.
The ventilation slits are
covered or dusty.
Clean with a vacuum or
brush.
The door has been
opened too frequently, or
a large amount of fresh
food has been put in at
once.
Once the fridge gets
down to the set
temperature the
compressor will turn off.
The door is not closed.
Check that the door has
been closed properly.
Issue
Possible fault
Solution
The alarm is ringing.
The appliance door has
Close the door.
been open for longer than
5 minutes.
Issue
Possible fault
The alarm is ringing and The door is not closed.
the "alarm" indicator is
A large amount of food
flashing.
was loaded at the same
time.
There has been a power
failure.
32
Solution
Once the alarm condition
has been corrected, the
alarm will turn off and the
"alarm" indicator will stop
flashing.
Causes of noises
Normal noises
What causes them?
Brrrrr...
A humming noise is made by the motor (compressor). This
noise can get louder for brief periods when the motor
switches on.
Blub, blub....
A gurgling noise can be heard when the coolant circulates
through the pipes.
Click....
Clicking sounds occur whenever the thermostat switches the
motor on or off.
Sssrrrrr....
In multi-section and frost-free appliances, the movement of
air circulating through the appliance can sometimes just
barely be heard.
In appliances with a water tank, a humming noise can be
heard when the water pump is running.
Crack...
A cracking noise can be heard when the appliance materials
expand.
Please bear in mind that a certain amount of noise is unavoidable (from the
compressor and the coolant circulating through the system).
Noises that you
can easily
eliminate
Possible cause
Rattling, clinking The appliance is not level.
Remedy
Realign the appliance using a
spirit level, by raising or
lowering the screw feet
underneath the appliance.
The appliance is touching
another appliance or piece of
furniture.
Move it away.
Drawers, baskets or shelves
are jiggling or are stuck.
Check all removable items
and refit them correctly.
Bottles or containers are
touching.
Separate them.
The transport cable clips are Remove the cable clips.
still hanging on the back of the
appliance.
33
After sales service
In the event of a fault which you cannot
easily fix yourself, please contact the
Miele Technical Service Department at
the address on the back of this booklet.
When contacting the Technical Service
department, please quote the model
and serial number of your appliance
given on the data plate inside the
appliance.
MieleCare
(USA only)
MieleCare, our Extended Service
Contract program; gives you the
assurance of knowing that your
appliance investment is covered by 5
years of worry-free ownership.
MieleCare is the only Extended Service
Contract in the industry that guarantees
repairs by a Miele Authorized Service
Provider using genuine Miele parts.
Only genuine Miele parts installed by
factory-trained professionals can
guarantee the safety, reliability and
longevity of your Miele appliance.
Please note that unless expressly
approved in writing by the Miele Service department, Extended Service
Contracts offered by other providers for
Miele products will not be recognized
by Miele. Our goal is to prevent
unauthorized (and untrained) service
personnel from working on your Miele
products, possibly doing further
damage to them, you and/or your
home.
To learn more about MieleCare
Extended Service Contracts, please
contact your appliance dealer or visit
us online at:
http://mieleusa.com/mielecare
34
35
Installation Instructions
Information is subject to change. Please refer to our website to obtain the most
current product specification, technical & warranty information.
To prevent accidents
and machine damage
read these instructions
before
installation or use.
Caring for the environment
Disposing of the packaging
materials
The packaging is designed to protect
the appliance from damage during
transportation. The packaging materials
used are selected from materials which
are environmentally friendly for disposal
and should be recycled.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of children. Return
the packaging to your dealer.
Disposal of your old appliance
Old appliances may contain materials
that can be recycled. Please contract
your local recycling authority about the
possibility of recycling these materials.
Instead, please contact your
municipality's waste collection center to
return and recycle electric and
electronic appliances.
Please take care not to damage the
pipework while the appliance is being
stored for transport to a waste disposal
facility.
By protecting the pipework, you help
keep the coolants and compressor oil
from contaminating the environment.
Before discarding an old appliance
disconnect it from the electrical supply
and cut off the power cord to prevent it
from becoming a hazard.
37
Installation
Installation site
Have the appliance installed by a
qualified technician, according to
the enclosed installation
instructions.
WARNING
This appliance is top-heavy and
must be secured to prevent it from
tipping forward.
Keep the door closed until the
appliance is completely installed
and secured as per the installation
instructions.
Empty weight of your machine:
K 18x3 SF . . . . . . . . . 476 lbs (216 kg)
K 19x3 SF . . . . . . . . . 516 lbs (234 kg)
Climate Range
The appliance is designed for use
within certain climate ranges (ambient
temperatures) and should not be used
outside this range. The climate range of
this appliance is stated on the data
plate inside the appliance.
Climate
range
SN
N
ST
T
Ambient room temperature
+50°F (10 °C) to +90°F (32 °C)
+60°F (16 °C) to +90°F (32 °C)
+60°F (16 °C) to +100°F (38 °C)
+60°F (16 °C) to 110°F (43 °C)
Operating in a room which is too cold
will cause the compressor to switch off
for too long, causing the internal
temperature in the appliance to rise
with the risk of food deteriorating and
going off.
38
The appliance should be installed in a
dry, well ventilated room.
Do not install the appliance:
- outdoors,
- in an environment with dripping
water,
- in rooms which are at risk of frost.
The installation location should not be
exposed to direct sunlight, nor near a
heat source, such as an oven,
radiator, etc.
The ambient temperature should not
drop below 55°F (13°C) or rise above
110°F (43°C), otherwise malfunctions
may occur.
If installation next to a heat source is
unavoidable observe the following
minimum distances from the heat
source:
– 1 1/4" (3 cm) from an electric cooktop
or electric oven.
– 12" (30 cm) from a gas or oil
cooktop, range or oven.
The following should also be taken into
consideration:
– The electrical outlet must be easily
accessible in case of an
emergency,not concealed behind
the appliance.
– The plug and cord must not touch
the rear of the appliance as they
could be damaged by vibrations
from the appliance.
– Do not plug in other devices behind
this appliance.
Installation
Important! When there is high
humidity a build-up of condensation
on the outer surfaces of the
appliance can occur.This can cause
the surfaces to corrode.To prevent
this, it is advisable to install the
appliance in a dry and/or an
air-conditioned room with sufficient
ventilation.Please ensure that doors
close and seal properly after
installation and that the appliance is
installed in accordance with these
installation instructions and and with
the required ventilation openings.
– If the room is too cold, it will cause
the cooling system in the appliance
to remain off for too long.This can
cause the temperature in the
appliance to rise, resulting in
damage.
39
Installation
Base
Ventilation
A fully loaded appliance is very heavy.
The load-bearing capacity of your floor
must meet the following requirements:
The air intake and outlet must not be
blocked or covered in any way. They
also need to be dusted/cleaned on a
regular basis.
K 18x3 SF . . . . . . . . 1,056lbs (479 kg)
K 19x3 SF . . . . . . . . 1,254 lbs (569 kg)
Installation niche
To ensure that the appliance is installed
securely and functions properly, the
base must be flat, level and made of a
hard, rigid material.
To ensure safe, trouble-free installation
and the best possible cosmetic result,
check to be sure that the installation
space complies with the installation
dimensions. See "Niche dimensions".
If in doubt, contact Miele.
Furniture/fixtures
The new appliance will be mounted
securely to adjacent and overhead
furniture/fixtures.
For this reason it is essential that all
attachable furniture/fixtures are
connected securely to the base or the
wall by suitable means.
40
The side walls of the installation cavity
must be plumb.
The minimum thickness of the side
walls and the top wall must be 5/8"
(16 mm).
The minimum thickness of the toe-kick
panel must be ½" (13 mm). A thickness
of 3/4" (19 mm) is recommended.
Installation
Stainless steel panels
Side-by-side
Stainless steel door panels and toe-kick
covers are available from Miele.
This appliance can be installed
"side-by-side" with another
fridge/freezer using a "Merging Kit".
Installation options
The "Merging Kit" is available from
Miele.
There are many different installation
options. These are limited only by the
design of the kitchen.
The door hinge cannot be
exchanged.
Single column
The appliance can be installed at any
preferred location in the kitchen.
However, be sure the door will open
and close properly in the chosen
location.
Contact Miele or your dealer for
specific information about which
combinations will work with your
appliance.
For instructions on how to attach the
appliances and install the heating
mat, please refer to the instructions
included with the "Merging Kit",
available from Miele.
Installation without a partition using
the "Merging Kit"
If the appliances are installed directly
next to each other (without a partition),
they need to be attached together
using the "Merging Kit".
41
Installation
Installation with partition using the
"Merging Kit"
The minimum thickness of the partition
is 5/8" (16 mm).
Side panels
If one side of the appliance is visible, a
side panel must be used.
The side panel must be firmly secured
to the wall, the floor and the overhead
furniture/fixtures before the appliance is
placed in the cavity.
The dimensions of the side panel are
taken from the opposite wall of the
installation space. During installation,
ensure that the cavity is square and the
measurements are correct.
If there is a partition with a thickness
from 5/8" (16 mm) to 6 5/16" (160 mm)
between the adjacent appliances, then
each appliance should be individually
installed within its own niche using the
mounting accessories included.
The "Merging Kit" will also be needed.
The "Merging Kit" is available from
Miele.
Installation with partition without
using the "Merging Kit"
If there is a partition with a thickness of
more than 6 5/16" (160 mm) between
the adjacent appliances, then each
appliance should be individually
installed within its own niche using the
mounting accessories included (the
"Merging Kit" is not necessary).
42
Installation
Adjusting the door opening
angle (optional accessory)
Depending on the installation site, it
may be necessary to adjust the door
opening angle to 90°.
^ Open the door.
^ Insert the banking pin through the
holes and drive in with a hammer.
The door opening angle is now limited
to 90°.
43
Dimensions
Door dimensions (open min. 90°)
A
K 18X3 SF 32 5/8" (829 mm)
K 19X3 SF 38 11/16" (982 mm)
44
Dimensions
Niche dimensions
A
B
K 18X3 SF
30 ½" (774.6 mm)
30" (762 mm)
K 19X3 SF
36 ½" (927 mm)
36" (915 mm)
45
Dimensions
Power supply
1. Power supply
A
K 18X3 SF
15" (381 mm)
K 19X3 SF
18" (458 mm)
,Power bars or extension cords
are not safe (risk of fire). Do not use
them to connect the appliance to
the power supply
46
Installing the appliance
Before you begin
Read these instructions completely
and carefully.
Have the appliance installed by a
qualified technician, according to
the enclosed installation
instructions.
Tools needed for installation
– Cordless screwdriver
– Torx screwdriver
– Hammer drill
– Wood drills in different sizes
– Hammer
– Rachet 5/16" (8 mm)
To reduce the risk of injury or
damage to the product, two people
should be used for installation.
These installation instructions are
intended for use by qualified installers.
In addition to these instructions, the
appliance must be installed in
accordance with all local codes. In the
absence of a local code, the following
should be used:
– Adhesive tape
– Multi-grip pliers
– Level
– Tape measure
– Square
When fastening the cabinet to the wall
behind it (see "Installing the appliance")
use:
– In the USA, the National Electric
Code, ANSI/NFPA 70 - latest
edition/State and Municipal codes
and/or local codes.
– suitable plugs/screws depending on
the type of wall.
– In Canada, the Canadian Electric
code C22.1 - latest edition/Provincial
and Municipal codes and/or local
codes.
Other
– several mounting brackets, if required.
– Stepladder
– Dolly, hand truck
– Wooden beam
(cross section min. 3" x 4"
[75 mm x 100 mm] as an alternative
tilt protection, length depends on the
width of the installation cavity)
– Wood screws in different sizes
Optional accessories
– "Merging Kit" for side-by-side installation
– RemoteVision module for wireless
monitoring
47
Installing the appliance
Aligning the housing unit
Check the installation niche
To ensure a safe, trouble-free
installation and the best possible
cosmetic result, check to be sure
that the installation space complies
with the installation requirements.
^ Check the base (see "Installation").
^ Check the dimensions of the cavity.
^ Check that the cavity is square.
^ Check the location of the power
outlet.
The housing unit must be carefully
aligned using a spirit level before
installing the appliance. The unit
corners must be at right angles, as
otherwise the furniture door will not
align correctly with the 4 corners of the
appliance.
– The side panels of the housing must
be even.
– The housing unit panels must be at
least 5/8" (16 mm) thick.
– The plinth facing must be at least
1/2" (13 mm) thick, preferably 3/4"
19 mm).
^ Check that all furniture parts in the
vicinity of the appliance are securely
connected to the wall.
^ Check that the adjacent
furniture/fixtures do not collide with
the open door.
Before installation
,Caution - the appliance is very
heavy. Use caution when unpacking
and opening the door, danger of
tipping.
^ To protect the base from damage
during installation, attach a hard
board, linoleum, etc., to the floor in
front of the intended installation
location.
^ Remove any cable clips from the
back of the appliance.
^ Take the supplied accessories out of
the protective packaging.
48
Installing the appliance
There are transportation safety
devices inside the appliance to
protect the shelves and storage
compartments until installation is
complete. Do not remove them, or
parts may be damaged.
^ Check the appliance for damage in
transit.
Do not install the appliance if it is
visibly damaged. If in doubt, contact
your dealer.
RemoteVision module
installation
(optional accessory)
Always disconnect the appliance
from the power supply when
performing installation, maintenance
or service work.
Install the RemoteVision module
before placing the appliance in its
installation niche.
Once connected the RemoteVision
module will increase the energy
consumption of the appliance.
The slot for the RemoteVision module is
located in the lower area of the back of
your appliance.
^ Loosen the bracket that holds the
appliance to the pallet.
,Caution! The appliance is no
longer secured and may be
unstable.
^ From the rear of the appliance
carefully lift it from the pallet.
^ Unscrew the screws a on the cover
b and pull off the sticker c.
^ Remove the cover b.
Once the appliance is on the ground it
can be wheeled around.
49
Installing the appliance
^ Push the module into the slot until it
locks into place.
^ Connect the appliance to the power
supply and turn it on. After several
seconds the indicator light e will
come on.
The indicator light will display different
colors one after the other; any control
light at the end indicates that the
module was correctly installed.
If the indicator light does not come on,
installation of the module was
unsuccessful. In that case, repeat the
process. If that does not correct the
problem, contact Miele.
^ Pull the antenna d straight out.
^ Guide the cover b over the antenna
d and screw on the cover.
^ Angle the antenna d so that it faces
to the right or left.
^ If necessary, disconnect the power
supply and continue installing the
appliance.
Preparing the installation
niche
,Keep the appliance door closed
until it is securely fastened in the
niche. Tipping hazard.
Because of the size and weight of
the appliance, it is essential to
ensure that the appliance cannot tip
over once it has been mounted in
the niche.
50
Installing the appliance
Mounting Accessories
The mounting accessories needed for
installing the appliance into the niche
are included in the packaging. Several
plastic bags are included which are
numbered alphabetically.
The bag needed for each step will be
marked with its respective letter.
Anti-tip brackets
The anti-tip brackets a keep the
appliance safely secured in the
installation niche b and prevent it from
tipping.
Two anti-tip brackets are
recommended for each appliance. For
side-by-side installations 4 brackets are
recommended.
^ Position the anti-tip brackets on the
left and right in the installation niche
so that there is no more than 3/8"
(10 mm) of space between the
brackets and the side walls.
^ Mark the drill holes in the anti-tip
brackets on the back wall and on the
ceiling of the installation niche.
^ Set the brackets aside - they will be
needed again later.
, Risk of tipping
The installation niche must be
securely attached to the wall behind
it. This is the only way the
appliance, which is later secured in
the niche, can be prevented from
tipping!
Screws are supplied with the
appliance for various
applications/materials.
If the anti-tip brackets cannot be
attached securely with the screws
supplied, an alternative anti-tip
device can be used.
Assure that there are no electrical
wires in the area which the screws
could penetrate - risk of injury and
damage.
51
Installing the appliance
In a cabinet without a back wall
^ Now attach the installation niche to
the wall.
The built-in cabinet must be secured to
the wall behind it with several screws.
In a cabinet with a back wall
^ screw the cabinet to the wall behind
it in several places using suitable
mounting brackets.
For this, use suitable plugs/screws
depending on the type of wall.
^ screw the back wall of the cabinet in
several places directly to the wall
behind it.
For this, use suitable plugs/screws
depending on the type of wall.
52
Installing the appliance
Securing an alternative anti-tip
device
– The beam must cover the appliance
by at least 2" (50.8 mm).
^ Mark the installation height (lower
edge of the beam) on the rear wall of
the niche.
^ Select screws according to the
thickness of the wooden beam.
Example: 3 ½" (89 mm) screw for 2x4
beam.
^ Determine the number of screws
based on the cavity width, to ensure
that the beam will be attached
securely.
^ Locate wall studs near the rear wall
of the cavity and mark drill holes in
the beam.
^ Pre-drill the wooden beam.
^ Attach the wooden beam to the rear
wall of the niche.
If the anti-tip brackets cannot be
attached securely, an alternative
anti-tip device can be used.
Ensure that there is no "give" between
the appliance and the anti-tip device.
If possible, always screw the
wooden beam to existing studs.
– Cut a wooden beam
(cross section min. 3" x 4"
[75 mm x 100 mm] to the required
length).
– The length is equal to the width of
the installation niche.
– If the installation niche is deeper than
the appliance, select a beam with a
larger cross section, or attach two
beams.
53
Installing the appliance
Sliding the appliance into the
installation space
If a side-by-side installation is
desired, connect the two appliances
together. See the Installation Manual
included with the "Merging Kit".
^ Plug the appliance into the power
outlet a.
The plug of the appliance should be
easily accessible after installation.
If the plug is not accessible after the
appliance has been installed,
disconnection from the power
supply should be completed via the
circuit breaker.
In the case of side-by-side
installations, a separate outlet must
be used for each appliance.
^ Unscrew the plinth.
^ To prevent the power cord from
becoming caught:
Tie a piece of string to the middle of
the power cord and feed it forward
under the appliance. When sliding
the appliance in, pull the cable
forward b.
^ Carefully slide the appliance into the
space.
If resistance is felt when attempting to
slide the appliance into the installation
niche - for example, because the floor
is uneven,
^ Turn the rear adjustable wheels
slightly outward (see "Aligning the
appliance"), then push the appliance
in.
Be careful not to damage the power
cord attached to the floor.
^ To protect the corners of the
installation space, attach edge
protectors where needed (not
included).
54
^ Remove the edge protectors.
Installing the appliance
Aligning the appliance
^ Align the appliance with the custom
front.
^ Unscrew the height-adjustable feet
until the mark on the base has
reached the indicated guide
dimension 1 1/4" (32 mm). The guide
dimension of 1 1/4" (32 mm) is
related to a niche height of 84"
(2134 mm).
Important!
The height-adjustable feet can only
be unscrewed as far as the mark 2
3/16" (62 mm) on the base (max.
niche height of 85 3/16" (2164 mm).
The height-adjustable feet at the front
and rear can all be adjusted from the
front:
– Front feet:
Adjust with a rachet 5/16" (8 mm) c
– Rear feet:
Adjust with a (cordless) screwdriver
and/or a rachet 5/16" (8 mm) for fine
adjustment d
Important!
When unscrewing the
height-adjustable feet, proceed
gradually, alternating between left
and right.
^ Align the appliance again using a
level.
^ If using a wooden beam as an
alternative anti-tip device, rotate the
appliance all the way toward the
wooden beam.
55
Installing the appliance
Attaching the appliance to the
installation niche
Attaching the toe-kick cover
The maximum height of the toe-kick
cover is 4" (102 mm) from the top of
the floor. Do not cover the ventilation
slits in the plinth. Risk of damage to
the appliance.
^ If required, cut the toe-kick cover to
the required length and height.
^ Open the appliance doors.
^ Fasten the appliance on the left and
right hand sides with the 3 (supplied)
wood screws.
If there is a fairly large gap above the
appliance, cut a wooden beam to fit
exactly and place it in the gap.
^ Attach the plinth to the appliance.
^ Put the included cover plates in
place.
56
Installing the appliance
^ Insert the foam pieces back into the
sides.
^ Position the air separator in the
center of the appliance door.
^ Remove the foil from the adhesive
strips.
^ Attach the toe-kick cover to the
plinth.
Mounting the air separator
The air separator keeps the supply and
exhaust air separate. This prevents
warm exhaust air from flowing into the
machine, optimizing the energy
performance of the unit.
^ From below, screw the air separator
firmly onto the door with the 2
screws.
^ If necessary, shorten the three parts
of the air separator.
57
Electrical connection
, Avoid the risk of electrical
shock
- Plug into a grounded 3-prong
outlet.
- Do not move the ground plug.
- Do not use an adapter.
- Do not use an extension cord.
Failure to follow these instructions
can result in death, fire, or electrical
shock.
Improper connection of the
equipment grounding conductor
may result in electric shock. If you
are in any doubt as to whether the
appliance has been properly
grounded, have the appliance
checked by a qualified electrician or
service technician.
Installation, repairs and other work
by unqualified persons could be
dangerous.
Before installing the appliance,
verify that the voltage, load and
circuit rating information found on
the data plate match the household
electrical supply.
If there are any questions regarding the
electrical connection of this appliance
to the power supply, please consult a
licensed electrician or call the Miele
Technical Service.
U1-800-999-1360
V1-800-565-6435
58
The appliance is supplied with a
UL-listed, 3-wire power cord and
NEMA 5-15 P plug ready for connection
to a 120 V, 60 Hz supply.
The fuse rating is 15 amps.
The appliance requires a 3-wire
receptacle.
The receptacle must be installed by a
licensed electrician only.
In the case of side-by-side installations,
a separate outlet must be used for each
appliance. Ideally, the power outlet
should be next to the appliance and
easily accessible. Do not connect the
appliance to the power supply by an
extension cord. Extension cords do not
guarantee the required safety of the
appliance (danger of overheating).
If any changes are needed to the
household wiring or power supply, this
work must be performed by a qualified
electrician.
RemoteVision (optional accessory)
Miele's RemoteVision Wi-Fi technology
creates a 'virtual link' between your
appliance and our monitoring center. If
a fault occurs, Miele's client service
center will be notified and contact you,
or another trusted individual identified
on your call roster, in order to gain
access to your appliance to fix the
problem.
For information on set-up and
installation of the RemoteVision module
see the "Installation" section of this
manual.
Be sure your wireless system meets the
following requirements
– A wireless router that supports an
IEEE 802.11b/g protocol
– Windows XP® or newer operating
system, Mac® OS X 10.3 or higher
– Cable or DSL modem
– Microsoft® Internet Explorer 6 or
higher, Safari 2.0 or higher, Firefox
1.5 or higher
* Please note that each wireless router
manufacturer supplies their own device
drivers and setup programs. Due to the
differences in manufacturers, exact
router setup instructions are not
included in this manual. Wording and
instructions may vary.
59
RemoteVision (optional accessory)
Accessing the RemoteVision
control panel
^ Tap the X button until ; appears in
the display.
^ Touch the access button "p" to
confirm.
^ Touch the access button "p" so it
turns yellow.
See the table on the following page for
a description of each setting in the
display.
^ Note the position of the X button, but
do not touch.
^ Use the Y or X buttons to select the
RemoteVision options.
^ Touch the access button "p" again so
it turns white.
The module has been connected to
the network when ; # appears in the
display.
If ; # does not appear, refer to the
"Network options" section of the
XKM 2000 Installation Instruction
manual.
Only the access button "p" is visible.
^ Place one finger on the position of
the X button and hold (the X button
will not be visible).
^ While holding down the X button,
press the access button "p" once.
Keep holding the X button down until
the following appears in the display
(approx. 5 seconds).
^ Press and hold the access button "p"
for 2 seconds to confirm the change.
^ To return to the main menu, tap the X
button until a solid ; - appears in the
display.
^ Press the access button "p" to
confirm.
Access to the Custom settings mode is
now active for approximately 10
seconds.
^ Tap the X button until a ; appears in
the display.
^ Touch the access button "p".
You have left the Custom settings
mode.
When you are in the Custom settings
mode the door alarm is turned off
automatically. Once the door is
closed it is reactivated.
60
RemoteVision (optional accessory)
MasterCool control panel options for RemoteVision
Status indicators Description of function
Flashing ; ~
Module booting phase
Flashing ; ‡
Not connected to network
Flashing ; |
Connection to network established, no IP address
assigned
Solid
;#
Connected to network
Flashing ; <
In Ad-Hoc Mode, not connected
Flashing ; =
In Ad-Hoc Mode, connected
Selectable
options
Description of function
;-
Back
;2
Reboot the module
;3
Reset to factory settings
;4
Enter Ad-Hoc Mode
Note: If you cannot select any option (other than ; - "Back", the module has not
been installed correctly.
61
62
63
K 1803 SF, K 1903 SF
en - US, CA
M.-Nr. 09 920 730 / 00
Download PDF