INSTRUCTIONS
F170(N) B/W
F191(N) B/W
Chelsea Auto-Close Hallway Security Gate
With Stay-Open Feature
IMPORTANT! READ AND FOLLOW THESE INSTRUCTIONS
CAREFULLY AND KEEP FOR FUTURE REFERENCE
If you sell or give away this product,
make sure you give this instruction to the new owner.
This safety gate complies with EN1930:2011
F170/F191 fits openings 97-108cm / 38-42.5in.
WARNING
WARNING - Incorrect installation can be dangerous;
WARNING - Do not use the safety barrier if any components are damaged or missing;
WARNING - The safety barrier must not be fitted across windows;
WARNING - Never use without mounting cups;
This safety barrier is for domestic use only;
This safety barrier is suitable for use with children up to 24 months of age;
Never use with a child able to climb or dislodge/open gate;
The surfaces that the gate is to be fixed to must be suitable for the purpose and
must be structurally sound;
If the barrier is to be used at the top of the stairs, it should not be positioned
below top level;
If the safety barrier is used at the bottom of the stairs, it should be positioned
at the front of the lowest tread possible;
This gate has an automatic close system;
This gate is intended for indoor use and is not to be exposed to outdoor elements;
Install this gate away from heaters and other sources of heat.
1
PARTS LIST
1
Gate Panel
2
Upper Locking Set
3
Release Switch with Latch
4
Right Upper Corner
5
Tension Knobs
6
Bolts with Rubber Pads
7
Mounting Cups
8
Gate Frame
9
Lower Locking Set
NOTICE TO
CUSTOMERS
1
2 3
4
5
6
7
THE GAP IN THIS GATE IS NOT A FAULT.
THE GAP WILL DISAPPEAR WHEN THE
GATE IS CORRECTLY INSTALLED.
PLEASE INSTALL GATE ACCORDING TO
MANUFACTURER’S INSTRUCTIONS.
8
IMPORTANT NOTICE
to Customers
The gap in this gate is NOT a fault.
The gap will disappear when the
gate is correctly installed.
Refer to enclosed instructions for
correct installation procedures.
F - Gate Notice
9
WARNING: This package contains small parts and
sharp points in an unassembled state. Keep out of
reach of children. Adult assembly required.
INSTALLATION
1. Measure the width of the opening of where you intend to install the gate.
Ensure the surface that you are mounting the gate is structurally sound such as solid timber,
brick or masonry.
For plaster/gyprock surface, locate the timber beam or stud behind and mount in this location
(mounting on plaster/gyprock alone is not strong enough and not safe). Do not mount to glass.
For openings over 108cm / 42.5in select the appropriate Gate Extension(s).
1A
97 - 108cm / 38.2 - 42.5in
2
2. To use with Gate Extensions.
Extension Frame
Extension Pin
Gate Frame
Tension Knob with
Rubber Pads
Tension
Bolt
Insert Extension pins into the holes on the outside of the Gate Frame (2A / 2B).
Next, slip Extension Frames over the Pins.
Finally, slide the Tension Knobs and Bolts with Rubber Pads.
For all other Gate Extensions
* For 9cm (3.5in) Gate Extensions
2A
Gate Frame
Insert LONG END of
EXTENSION PIN
into Gate Frame
2B
Gate Frame Insert SHORT END of
EXTENSION PIN
into Gate Frame
Tension
Knob
Gate
Extension
27cm
Tension
Knob
Gate
Extension
9cm
9cm
27cm
18cm
9cm
9cm
WARNING
27cm
Gate Extensions
*#159/#192 - 9cm / 3.5in
#171/#193
#172/#194
#831/#841
#832/#842
#833/#843
#834/#844
#835/#845
- 18cm / 7in
- 27cm / 10.5in
- 36cm / 14in
- 45cm / 17.5in
- 54cm / 21in
- 63cm / 24.5in
-100cm / 39in
18cm
9cm
A maximum of 4 Gate Extensions can be used,
2 on each side of gate. Do NOT install 3 Gate Extensions on the same side of gate.
3
3. To Install, place the gate in the opening so that the bottom of the Gate Frame is completely flat on
the floor (3A), and it is perpendicular to the openings and the floor (3B & 3C).
For use on stairs (3F).
Fasten the Mounting Cups to the wall (3D & 3E) with double-sided adhesive tape or double-sided
adhesive tape and screws.
Note: Ensure that they are are aligned vertically, so that the Mounting Cups at the top are directly
above the ones at the bottom.
3A
3C
Top view of gate
3B
WARNING
Side view of gate
Never use without Mounting Cups.
3D
floor
floor
3E
floor
Jx4
Gx4
Jx4
Gx4
Fasten Mounting Cups to the wall with
screws or double-sided adhesive tape.
3E
Top of stairs
Bottom of stairs
If the gate is used at the
bottom of the stairs to prevent
the child from climbing up the
stairs, it must be placed on
the lowest stair.
If the gate is to be used at the top
of the stairs to prevent the child
from falling down the stairs, it
must not be placed on any stair
below the level of the top stair.
4
4. Partially slide the Bolts with Rubber Pads and Tension Knobs outwards from the Gate Frames /
Extension Frames into Mounting Cups.
5. Tighten both of the bottom Tension Knobs (5A) by
5A
turning them clockwise at the same time (5A & 5B).
NOTE: Make sure the bottom of the gate frame
remains completely flat on the floor.
Next, tighten both of the Tension Knobs at the top at
the same time by turning them clockwise (5C).
Tighten
inward
Gate frame
5C
5B
Tension knob
Tighten inward and align the Indicator Lines
Tighten
inward
Tighten
inward
Note: When first installing, the gate will have
this gap. This is normal and will disappear
when gate is completely installed.
6. Tighten the Tension Knobs until the two Indicator
Lines, located on the Upper Locking Set and on the
Right Upper Corner, align horizontally (6A).
6A
When correctly tightened, the distances
between Tension Knobs and Rubber Pads
should be equal (6B, 6C).
Distance should be equal
Keep this gap about
1mm / 0.04in
6B
6C
Indicator
Lines
Distance should be equal
5
OPERATION
7. To open the gate: Slide the Gate Release Switch (7A). Lift the Gate Panel upward (7B). Gate swings open
in both directions (7C).
Slide
Gate Release
Switch
7A
7B
7C
Lift Gate Panel
up to open
Gate opens in
both directions
8. To close the gate: Release the Gate and it will swing closed automatically.
Try this action several times and make sure:
• The Upper Lock Rod and the latch of the Switch are completely latched within the Lock Holder at
Right Upper Corner (8A).
• The Lower Lock Rod of the Gate Panel fits securely into the Lock Holder of Gate Frame (8B).
• The Warning Line has disappeared (8C & 8D).
8A
Upper
Lock Rod
Right Upper
Corner
Gate
Panel
8B
8C
Warning line
Lower
Lock
Rod
Lock Holder
Lock
Holder
Gate Frame
8D
The warning line will disappear when the gate is locked properly.
RED
The warning line will appear RED color if the gate is opened or not locked properly.
6
9. For easy walk through use Smart Stay Open System:
To engage the Smart Stay Open System swing gate in chosen direction to its maximum opening (9A).
Gate will stay open. Close as required.
Caution: When using the Stay Open System, the automatic closing feature is not in operation.
Keep gate closed when children are present.
9A
TOP VIEW OF GATE
Gate in CLOSED position
Swing to OPEN positions
7
MAINTENANCE & CARE
• Gate must be fitted according to instructions, to ensure it works correctly.
• Regularly check gate to ensure it is fitted properly and securely. Adjust as required.
• Regularly check tension knobs and rubber pads to make sure the gate is securely in place.
• Do not use the safety gate if any components are damaged or missing.
• To clean, wipe surface with a damp cloth or sponge using mild detergent and warm water.
Never clean with abrasive, ammonia based bleach based or spirit type cleaners.
• If the gate does not stay in position or does not swing closed properly, the gate may not be
installed properly.
Remove and re-install gate, make sure the gate is installed vertically.
• Indicator Lines must be correctly aligned. Keep 1mm / 0.04in gap.
• Any additional and replacement parts should be obtained from Tee-Zed Products.
CONTACT DETAILS
Tee-Zed acknowledges that its customers may be entitled to
statutory consumer guarantees and does not seek to exclude
or limit them. These guarantees include that Tee-Zed’s
products are of acceptable quality. This Tee-Zed product is for
the specific purpose detailed in the instructions and
packaging and Tee-Zed considers use outside of that purpose
to be abnormal use. To the maximum extent permitted by
law, Tee-Zed does not accept any liability for damage:
• arising from abnormal use of the products;
• caused by installation or removal of the products other
than in accordance with the supplied installation and
removal instructions; or
• arising under the law of tort or contract.
Dreambaby® products by
Made in Dongguan, China.
©2015 Tee-Zed Products Pty Ltd
Tee-Zed Products Pty Ltd,
PO Box 2022, Bondi Junction NSW 1355
Australia Tel: +61 (0)2 9386 4000
info@tee-zed.com.au
Tee-Zed Products (N.Z.) Ltd
PO Box 64013, Botany Town Centre, Auckland
New Zealand Tel: +64 (0)9 274 8788
info@tee-zed.co.nz
Tee-Zed Products Ltd
PO Box 29227, Dunfermline, KY12 2DN
United Kingdom Tel: +44 (0)844 800 9445
info@tee-zed.co.uk
8
www.dreambaby.com.au
www.dream-baby.co.nz
www.dreambaby.co.uk
www.youtube.com/dreambabytv
www.facebook.com/dreambabysafety
www.twitter.com/dreambabysafety
Download PDF