B
Complete the registration process using the following steps:
1. Enter registration number included on the letter in
the self-installation kit.
2. When asked if this is your number, press OK.
3. You will see a “successful” message followed by an
automatic reboot, which will take 2-3 minutes.
Registration / Enregistrement
Enter number/ Enrer le numéro:
1
2
3
4
LINK
HD
RECORD
POWER
MENU
OK
Enter number and press OK / Enrer le numéro et appuyer sur OK:
fter the successful reboot you will automatically
A
be taken to LIVE TV (Channel 2 - FibreOP TV Help).
Enter 1234 when prompted for password.
WIRELESS TV RECEIVER
If you are adding more than one wireless receiver, repeat these steps starting at
Step 2. Installing Wireless TV Receiver.
SELF-INSTALLATION GUIDE
YOU DID IT! You only need to set up your personalized settings and you can start
to enjoy the freedom of wireless TV.
4
Personalizing your NEW Wireless TV Receiver
Congratulations!
You are about to install our most advanced wireless receiver enabling you to
move your TV anywhere.
Customize your Wireless TV Receiver, press Menu > Settings on your remote and select:
a.Screen aspect ratio and high definition
b. Favorite Channels
c.Language preference
d. Parental Controls
Installation will take approximately 25 minutes. We hope you enjoy an even
better TV experience with your wireless TV receiver.
Let’s get started...
To learn how to re-establish your personalized settings, refer to your
FibreOP Welcome Guide or go to bellaliant.net/welcomeguide
If you are a new Wireless TV customer start at Step 1.
Need Troubleshooting or Help?
If at any point you receive an error message, start over and repeat the steps. If you are still having trouble,
visit bellaliant.net/selfinstall to watch videos and read Q&A’s or contact our help desk at 1 866 342-7367.
Important legal information regarding your Wireless Receiver: Additional fee(s) may apply. Wireless from the Video Access Point to the Wireless Receiver; power outlet and separate connection of Wireless Receiver to TV is required. For residential use in
a single household only. Limit three wireless receivers per household. Actual range of wireless signal will vary and may be limited by several factors including, but not limited to, electromagnetic interference, home construction material, obstructions, and
other environmental factors.
CONSELFINSTALLWR0914
If you are already a Wireless TV customer adding a new receiver start at Step 2.
1
Connecting Wireless Video Access Point
(VAP) to modem
Plug power cord from the Wireless Receiver into an electrical outlet and it will power up
automatically. If you skipped Step 1 because you already have a Wireless TV Receiver, go to your
VAP and reboot it by turning the power off and then back on. After about a minute, additional on
screen instructions will appear on your TV.
RESET
A
Connect the Wireless Video Access Point (VAP) to your
existing FibreOP Modem using the Ethernet cable included
in the box. Use any available port.
POWER
+12V DC
Note: If the power light does not illuminate ensure the power
switch is on (the switch is either on the front or back).
C
Wait at least FOUR (4) minutes before the next step. This
will allow the Video Access Point to be fully initialized.
For example, if you plugged the cable into HDMI 1 port on the TV, select this as the input.
If you have trouble, visit our support article on this topic at www.bellaliant.net/inputsource.
Video Access Point
(Back)
FibreOP Modem
(Back)
IMPORTANT!
If you do not have an open Ethernet
port on your existing FibreOP Wireless
Modem (Actiontec R1000H), call
1 866 342-7367 and be sure to leave
existing cables plugged in.
3
A
2
Set your TV to the proper input screen choosing the option that matches your cables.
ON
Plug the Wireless Video Access Point (VAP) into a working
electrical outlet using the VAP power cord. Ensure the
power light is illuminated green on the front of the Wireless
Video Access point.
OFF
Note: Your modem is close to where FibreOP comes into your
home and is usually located in the basement or garage.
B
B
ETHERNET
Pairing the Wireless TV Receiver
You will need to follow instructions as they appear on these screens. In Step 2, ensure you
hold the ok button for at least two seconds.
1
2
3
4
Installing Wireless TV Receiver
IMPORTANT!
X
NETWORK
Y
Pb
Pr
VIDEO OUT
L
R
AUDIO OUT
OPTICAL
HDMI
POWER
+12V DC
No cables should be connected to the network
port on the back of the Wireless TV Receiver.
Wireless TV Receiver (Back)
A
Connect the Wireless TV Receiver to your TV with the HDMI cable provided in your kit. You may
also use your own Composite or Component cables, if your TV does not support HDMI.
HDMI Cable
(included in your kit)
Component Cable
(not included)
Composite Cable
(not included)
Client Registration
Press OK to start Client Registration
Download PDF