Audi A3 - Scosche

2006-09
Audi A3
About the Vehicle
Make: Audi
Model: A3 (Non-Navigation)
Year: 2006-09
Standard/Optional
In-Dash 6 disc changer
BOSE Sound System
Navigation System
Satellite Radio ( XM or Sirius )
10 Speaker System
Speaker Notes
Front
In Dash Application
Dash Type :
Custom
Aftermarket Type: Din
Kit:
AU2392B
Harness:
VW03B
Antenna Adapter: VWA2B
A Pillar:
1.5'' Tweeter
Lower Door:
6 1/2” Midrange
Speaker Adapter: SAVW6
Speaker Harness: TBA
Factory Assembly: (3) T-25 Torx screws securing speaker.
Dimensions:
W= 5.25''
L= 5.75''
D= 5/8''
Rear
Wire Color Codes
Type: Premium Audio System Location: At Speaker
+12v Constant = Red/White
+12v Acc. Switch =
-12v Chassis Ground= Brown
+12v Illumination =
Antenna/Amp Remote =
Can-Bus (H)= Orange/Purple
Can-Bus (L)= Orange/Brown
LF+ = Red
LF- = Brown/Red
RF+ = Gray
RF- = Brown/Gray
LR+ = Lt. Green
LR- = Gray
RR+ = Yellow
RR- = Gray
Speaker Sizes
NOTES
When installing aftermarket 5 ¼"
or 6 ½" a speaker adapter is needed.
Speaker Sizes
Rear Door:
6.5'' Midrange
Speaker Adapter: SAVW6
Speaker Harness: TBA
Factory Assembly: (3) T-25 Torx scres securin speaker.
Dimensions:
W= 5.25''
L= 5.75''
D= 3-7/8''
NOTES
When installing aftermarket 5 ¼"
or 6 ½" a speaker adapter is needed
Rear
Drivers side Panel: 6 ½" sub
.
mounted to factory enclosure.
2006-09
Audi A3
Recommended: Disconnect negative battery cable
Radio removal
Images
Radio
1. Using DT2 radio removal tools remove the factory
radio. Disconnect and remove
Front Speakers
"A" Pillar
1. Using a PRT remove the "A" pillar. Disconnect
and remove.
2.Twist the tweeter counter-clockwise to release
tweeter from the "A" pillar.
Lower Door
1. Extract (1) T-25 torx screw from underneath the
arm rest on the door panel.
2. Using a PRT remove the door lock switch trim
panel. Extract (1) T-25 torx screw from behind the
lock switch cover.
3. Extract (3) T-25 torx screws from the bottom
edge of the door panel.
4. Using a PRT remove the entire door panel.
Disconnect and remove.
5. Extract (3) T-25 torx screws securing the speaker
to the door steel. Disconnect and remove
Front Speakers
Rear Speakers
Lower Door
1. Using a PRT remove the tweeter grill cover. Extract
(1) T-25 torx screw from behind the tweeter cover.
2. Using a PRT remove the power window trim
panel. Extract (1) T-25 torx screw from behind the
window switch trim panel.
3. Using a PRT remove the entire door panel.
Disconnect and remove.
4. Extract (3) T-25 torx screws securing the speaker
to the door steel. Disconnect and remove.
Rear Sub
1. Lift spare tire cover panel up.
2. Extract (1) T-25 torx screw from the side panel just
below the "D" pillar next to the vent.
3. Using a PRT remove the rear running board.
4. Using a PRT pop out the drivers side panel
enough to expose the sub woofer speaker
enclosure.
5. Extract (4) PHS securing the sub woofer to the
enclosure. Disconnect and remove.
6. Extract (3) 10mm bolts securing the enclosure to
the vehicles steel. Disconnect and remove.
Rear Speakers
Sub
Tweeter
Download PDF