mini dehumidifier - Global Industrial

MINI DEHUMIDIFIER
SD-350TI
With UV Light
SD-350
INSTRUCTION MANUAL
Please read these instructions thoroughly and
Keep it in a safe place for future reference.
BEFORE YOU USE YOUR DEHUMIDIFIER, PLEASE READ
THIS INSTRUCTION MANUAL CAREFULLY.
SAFETY NOTES
1. Do not connect the unit to any damaged AC electrical socket.
2. Ensure removable covers and containers are correctly fitted
before switching on the unit.
3. Always switch the unit off when not in use and before unplugging.
4. Do not use in the following locations:
• Next to or near a heat source (radiator, heater, dryer, etc.)
• Area where oil or water is likely to splash.
• Under direct sunlight.
• Near a bath, shower or swimming pool.
• In a greenhouse.
5. Never insert your finger or other foreign objects into grills or
openings. Take special care to warn children of these dangers.
6. Always unplug the unit before cleaning and maintenance.
7. Do not cover the unit and its air inlets/outlets.
8. Do not spray insecticides or any other flammable sprays on the
machine.
9. Do not spray water on the unit.
10. There are no user serviceable parts. Should the unit or power
supply cord become damaged, contact the manufacturer
immediately.
11. Empty the water tank before moving the dehumidifier.
12. This unit is intended for indoor use only.
DANGER
• Do not use this unit in a bathroom or shower.
• Never spray water directly onto the unit or adapter.
FEATURES & BENEFITS
This unit uses Peltier technology (Thermo-Electric)
BENEFITS:
• No compressor
• Quiet operation
• No vibration
• No refrigerant
IDEAL FOR:
• Small bedrooms
• Closets and cupboards
• Under sinks
FEATURES:
• Moisture removal rate of 11.83 ounces (350ml) per 24 hours
(86°F, 80% RH)
• 2 liters water tank capacity
• Compact design
• Full tank indicator light
• Auto cut-off when tank is full or removed
• TiO2 mesh & UV light kills germs and bacterial (SD-350Ti only)
PARTS IDENTIFICATION
Handle
Model: SD-350
Filter / UV light / TiO2 mesh (SD-350Ti)
Water full indicator
(Red)
On/Off Switch
Air inlet
Power indicator
(Yellow/green)
Water tank
DC adaptor socket
Water outlet plug
Floater
Model: SD-350Ti
Water full indicator
(Red)
UV indicator
(Orange/yellow)
Power indicator
(Yellow/green)
Water tank sensor
Water full sensor
DC adaptor
OPERATION
•
•
Make sure the unit is off before connecting power.
Allow sufficient space around the unit for air circulation.
1. Connect DC adaptor to the unit, then connect to power source.
2. Turn the unit ON. Power indicator will illuminate.
3. For SD-350Ti model, UV light automatically functions when the unit is in
operation. Both Power and UV indicator will illuminate.
4. When tank becomes full, the unit will auto shut off and the Full indicator
(in red) will illuminate.
5. To remove and empty water tank, first turn off the unit. Lift water tank
upwards and pull out gently. Gently remove tank cover and empty water.
NOTE: Do not press down on the floater – it may cause the floater to
become stuck.
TROUBLESHOOTING
PROBLEM
Unit has no power
POSSIBLE CAUSE
• Check your power source (circuit)
• DC adaptor / power source is not
properly connected
• Water tank is not in place
• Filter is not properly installed
• Water tank is full (red indicator light)
SPECIFICATION
MODEL
Voltage
SD-350
SD-350TI
12V
MAINTENANCE
Rated Power
•
Water Tank Capacity
4 pints (2000ml)
Moisture Removal
(per 24 hrs / 86°F, 80% RH)
11.83 oz (350ml)
•
•
•
Make sure the unit is turned off and disconnected from power source
before cleaning or maintenance.
Wipe the unit with damp cloth.
Air inlet can be cleaned by vacuuming with a brush attachment.
Never use bleach or abrasive cleaners.
FILTER (for SD-350TI model only)
• The filter is located on the top of the unit.
• First, remove the filter cover by placing thumbs on the two clips and push
in, then upwards.
• Pull on the ribbon to remove filter.
• The dust filter (black filter) can be removed by first removing the frame –
push in on one side and pull. Clean dust filter under lukewarm water and
dry completely.
• The white mesh is TiO2 mesh and also contains the UV light – DO NOT
wet. Tap to remove loose dirt or use a brush.
• To replace filter cover, align the inner edge first, then push down firmly.
• TiO2 mesh and UV light is effective for approx. 1 ½ years. Replacement
can be ordered from www.spt-usa.com or by calling 800-330-0388.
NOTE: Unit will not operate if filter or water tank is not in place.
60W ±5W
Dimension
8 W x 4.93 D x 13 H inches
Net Weight
3.65 lbs (w/o adaptor)
Gross Weight
5 lbs
Your Guarantee
If this product is found to be faulty as a result of faulty materials or
workmanship within one year from date of purchase, it will be repaired free of
charge.
This guarantee is subject to the following terms:
• Sunpentown must be notified of the fault.
• Proof of purchase must be presented to Sunpentown’s nominated
representative.
• The warranty will be void if the product is modified, misused or
repaired by an unauthorized person.
• The warranty after repair will not be extended beyond the original
one-year period.
• All replacement parts will be new or reconditioned.
• Parts, which are replaced, become the property of Sunpentown.
• The warranty applies to the use of the product in the USA only.
What is NOT COVERED:
• Warranty does not include freight charges.
• Incidental or consequential damage caused by possible defects with
this product.
• Damage to product caused by improper power supply voltage,
accident, fire, floods or acts of nature.
• Failure of product resulting from unauthorized modifications to the
product.
• Improper installation or failure to perform the necessary
maintenance.
This GUARANTEE is in addition to your Statutory Rights
SUNPENTOWN INTERNATIONAL INC.
14625 Clark Avenue, City of Industry, CA 91745
Tel: 626-336-2299 · Fax: 626-3367116
service@sunpentown.com
www.sunpentown.com
Download PDF