4-Light Adapter Light Kit 4-Light Adapter Light Kit 4

4-Light Adapter
Light Kit
Owner’s Guide and Installation Manual
Manual De Propietario
English
Español
Form# 43548-01
20090430
©2009 Hunter Fan Co.
Welcome
Your new Hunter® light kit is an addition to your home or office that
will provide comfort and performance for many years. This installation
and operation manual gives you complete instructions for installing
and operating your light kit.
We are proud of our work. We appreciate the opportunity to supply
you with the best products available anywhere in the world.
Before installing your light kit, for your records and warranty assistance,
record information from the carton and Hunter nameplate label.
Cautions and Warnings
Table Of Contents
Installing the Light Kit on Fans With
Removable Switch Housing . . . . . . . . 4
Installing the Light Kit on Fans With
Non-Removable Switch Housing . . . 6
Installing the Light Kit on the Hunter
Original . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . 9
• READ THIS ENTIRE MANUAL CAREFULLY BEFORE BEGINNING
INSTALLATION. SAVE THESE INSTRUCTIONS.
• Use only Hunter replacement parts.
• To reduce the risk of personal injury, install this light fixture only on
Hunter® fan types A through Z. Note: The fan type can be found on
the ceiling fan package or on the nameplate label located on top of
the motor housing of the ceiling fan.
• To avoid possible electrical shock, before installing light fixtures,
disconnect the power by turning off the circuit breakers both to
the outlet box and to its associated wall switch location. If you
cannot lock the circuit breakers in the off position, securely fasten a
prominent warning device, such as a tag, to the service panel.
• Connect house wiring to the fan before attaching the light fixture to
the fan.
• All wiring must be in accordance with national and local electrical
codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a
qualified electrician.
© 2009 Hunter Fan Company
2
43548-01 • 04/30/09 • Hunter Fan Company
Installation Methods for Hunter® Ceiling Fans
Your
® light kit can be installed on the Hunter
Fan Corte D’Azur, Custom Home, 42” Dominion, 52”
Dominion, Marseille, and Santa Barbara models.
Preparing the Light Kit
1.Shades are not included with this light kit. Be sure to
purchase shades for your light kit before installing this
light kit.
2.Disconnect power by turning off the circuit breakers
both to the outlet box and to its associated wall switch
location.
3
43548-01 • 04/30/09 • Hunter Fan Company
Installing the Light Kit on Fans With Removable Switch Housings
Before installing the light fixture, remove the wiring harness and its components
from the fan’s lower switch housing. Then install the wiring harness into the light
fixture.
1. Unscrew the three screws from the upper switch housing. Disconnect the 9-pin
plug connectors. Remove the lower switch housing.
2. Push the plug button from inside the lower switch housing to remove the
plug button and switch housing cap. Unscrew the two attachment screws on
the bottom of the switch housing.
NOTE: Save the plug button and switch housing cap should you choose to
remove the light fixture in the future.
3. Locate the reversing switch and carefully remove the two screws holding the
reversing switch to the lower switch housing. Then, remove the reversing
switch from the housing.
4. Remove the patented breakaway connector from the end of the fan pull
chain. Carefully loosen the bellmouth nut from the pull chain and remove
the pull chain switch from the light fixture housing.
5. Locate and carefully remove the two capacitors from the lower switch
housing.
Removable Switch Housing
9-Pin Plug
Connector
Screw
You have now disconnected the wiring harnness and its components from the
lower switch housing.
Steps 1–2
Steps 3–4
Reversing
Switch
Lower Switch
Housing
Plug Button
Light
Assembly
Housing
Capacitors
Fan
Speed
Switch
Light
Switch
WARNING: Improper installation could
cause the light fixture to fall.
Bellmouth Nuts
4
43548-01 • 04/30/09 • Hunter Fan Company
Installing the Light Kit
6. Insert the pull chain and fan pull chain switch through the round
opening on the side of the empty switch housing. Thread the
bellmouth nut over the pull chain and hand tighten the bellmouth
nut.
7.Reattach the breakaway connector to the pull chain.
8.Insert the reversing switch into the square hole on the side of the
switch housing. Install and tighten the two screws you removed
previously from the other switch housing.
9.Carefully place the capacitors in the switch housing.
Steps 6–9
Lower
Switch
Housing
Screw
Fan
Speed
Switch
You have now installed the wiring harness and its components in the
light kit.
10.Locate the two wires in the wiring harness (removed from the lower
switch housing) labeled “Connect Light Here” or “For Light use.” One is
white; the other is white with a black stripe. Unscrew the connectors to
expose the bare metal leads.
11. Locate the white wire and the black wire coming from the light fixture.
Connect the black wire from the light fixture to the black/white wire
from the wiring harness. Connect the white wire from the light fixture
to the white wire from the wiring harness.
To connect the wires, hold the bare metal leads together and place a
wire nut over them, then twist the wire nut clockwise until tight.
Wire
Connector
Steps 10–11
CAUTION: Be sure no bare metal wires or wire strands are visible
after making the connections.
12. Reconnect the 9-pin plug connector.
13. Install screws to reattach the light kit to the upper switch housing.
Plug
Connector
Detail
Plug
Connector
Light Kit
Step 12
5
43548-01 • 04/30/09 • Hunter Fan Company
Troubleshooting
Troubleshooting
Light does not come on
1. Make sure bulbs are installed properly.
2. Make sure breakers or fuses are on.
3. Verify that the light power lead is connected at the ceiling. Refer to
your ceiling fan manual for locating assembly and wiring.
Glass rattles
1. Make sure the glass shades are secure.
If you need parts or service assistance, please call
888‑830‑1326 or visit us at our Web site at
http://www.hunterfan.com.
Hunter Fan Company
7130 Goodlett Farms Pkwy. # 400
Memphis, Tennessee 38016
This Light Fixture Weighs 2 lbs. 6
43548-01 • 04/30/09 • Hunter Fan Company
Printed in China
Download PDF