Infiniti MA100 Treadmill manual

 Running belt lubrication
LUBRICATION OF TREADMILL IS ESSENTIAL TO OPERATION. THE TREADMILL MUST
BE LUBRICATED WITH 20ML SILICONE ONCE EVERY MONTH OR EVERY 20 HOURS
OF USE, WHICHEVER COMES FIRST.
TO LUBRICATE, LIFT RUNNING BELT AS HIGH AS POSSIBLE ABOUT HALFWAY
ALONG. INSERT STRAW FROM SILICONE BOTTLE SO IT REACHES TO THE MIDDLE
OF THE BELT AREA. START PUMPING WHILST WITHDRAWING STRAW TOWARDS
THE EDGE. 25 PUMPS ARE REQUIRED ON EACH SIDE. REPEAT PROCEDURE ON
OPPOSITE SIDE. IF BELT IS STUCK UNDER SIDE RAIL, USE A SCREWDRIVER TO
LEVER OUT. ENTIRE WIDTH MUST BE COVERED.
COVER FULL
WIDTH.
25 PUMPS PER
SIDE.
LIFT BELT AS
HIGH AS
POSSIBLE
ONLY INFINITI SILICONE MAY BE USED. MANY MARKET SILICONES
CONTAIN PETROLEUM ADDITIVES WHICH ARE DESTRUCTIVE. NO AFTERMARKET
LUBE KITS SUCH AS LUBE AND WALK ARE TO BE USED. INFINITI SILICONE MAY BE
PURCHASED FROM YOUR DEALER OR INFINITL IF UNSURE ABOUT LUBRICATION
PROCEDURE, CONTACT YOUR DEALER OR INFINITI.
91 Warranty void if treadmills are not
maintained with silicone correctly!
MA100/150/MA100X/150X
Ho )
1. Take off screw/f\, and nut Дот both 3. Attach screw ZN, and nut A back to both right/left sides of base
rightieft sides of base frame. frame and tighten the screws.
2. Upright the support handle and handle bar.
(FIG-1)
STEP 2: CONSOLE TUBE AND HANDLE BAR ASSEMBLY
1. Put console tube, right and left handle bars on floor.
2. Connect hand pulse cable) routed on left side of console tube to hand
pulse cable(F routed on left handle bar.
Insert hand puise cable connectors into console tube.
3. Connect hand pulse cable) routed on right side of console tube to hand
pulse cable(F routed on right handle bar.
insert hand pulse cable connectors into console tube.
4. Attach left side of console tube to left handle bar and then tighten with screw AN |
5. Pull out the PCB cable €2 from console tube, insert it from the side hole of right
handle bar and then pull it out from the bottom hole of right handle bar.
6. Attach right side of console tube to right handle bar and then tighten with screw
STEP 3: CONSOLE/RACKS ASSEMBLY
1. Attach left side of handle bar on left support handle and attach 2 pcs screws ay
But do not tighten the screws yet.
2. Connect PCB cable E2 routed from bottom hole of right handle bar to PCB(E3
cable routed from right support handle.
3. Attach right handle bar on right support handle and attach 2 pcs screws AN
4. Make sure handle bar set is in good position and then tighten 4 screws
together.
5. Attach left/right handle bar covers (Ron handle bars and then tighten with
screws A on both sides,
МАТ 00/150
Y Introduction 4
The treadmill has one user manual setting program and 3 preset
programs ( P1- P3). While you running with 3 preset programs mode,
the treadmill automatically changes valumn of Speed . However you can
change speed or incline manually at any time you desire. Before starting the
treadmill, ensure the main power switch, which is located at the front side of
machine, is in the "ON" position,
y Quick start 4
When the main power switch is in the "ON" position
and the safety key is inserted into the console, the monitor
window will display a flashing "0:00." Press "START"
to begin "Manual Mode.”
y Pro gram Operation A
PROGRAM OPERATION
Whife turn on power and safety key is inserted, the monitor
display a flashing 0:00 .
1. Select Program: Press Av to choose program P1-P3
2. Press MODE to enter. Function window display preset
time 30:00 Press Av to increase or decrease desired
workout time.
3. Press START to begin workout.
THE PAUSE FUNCTION
Pause the treadmill at any time during operation by pressing
"STOP" button once.esume treadmill operation by pressing
the "START" button.
THE RESET FUNCTION
Reset workout program and time by holding "STOP" button for
few seconds until the program window displays "0.00" .Repeat the
above steps to reset desired programs, level and workout time.
Durning workout, the user is able to press any of
desired quick speed key on display to get a specific
speed more quickly.
NOTE
1. When time read out 99:59 or 00:00, a series of "beep”
sound last for 5 seconds and then the motor stop.
2.When the safety key is pulled out in any situation, the
motor stops immediately and the system is reset to
manual setting.
3.The graphic of the workout profiles are printed on the
console. Each overall workout time will be segment into
10 sections.Segment time = overall workout time/10
EX: If overall workout time is set at 10 min, then each
segment will be 1 min each.
MAC 00/150
W Button Description 4
Start/Stop:
This will start the treadmill and this will stop the
treadmill. There will also be an emergency stop switch.
(Safety Key)
Mode:
This will select programs/level selection, This
will switch display data on data window during exercise.
Incline a : (only MA150)
This will select programflevel in setting mode before starting.
This will increase the elevation in 1 increment.
Inclinew : (only MA150)
This will select program/level in setting mode before starting.
This will decrease the elevation in 1 increment.
Speed 4 :
This will select program/level in setting mode before starting.
This will increase the speed in 0.1 km/h or 0.1 mph
Speed” :
This will select programflevel in setting mode before starting.
This wilt decrease the speed in 0.1 km/h or 0.1 mph
Walk, Joy, Run and Sprint
Four quick speed keys = Walk, Jog, Run and Sprint
Walk = 4 km/h or 3 mph
Jog = 6 km/h or 4 mph
Run = 8 km/h or 5 mph
y Display 4
The display is 1 LED windows with track.
Windows:
Data window:
Time:88:88
Distance:88.8 §(km or mile)
Ca: 8896
Pulse: ABB
Lap:8888
Scan: It displays above data ordinal.
Track:
Count for exercise distance. It is equal to 400
meter or 0.25 mile per lap.
SCAN FUNCTION:
Press "MODE" for 3 sec.
r 4 o rr mE A Na i,
Sprint = 10 kmor 6 mile es AA RI
pe em mT ù FE пе ШИЛО
E it i >
ES CIO TON h ARTO NTE JA Za Je Ct E i e A EE x
à farce SEEN ty 11 Ш авиа ут ‘ae ==
bing sss J e A E AE
FEA eS ere e i > Ip TT i
A Frome ger esis ih rl ë Ho oi, . ==:
SCAN FURCTION: do ree + JER 4 3 нон 42 if # ; mmr
Ш ye prepa ea TT” ji J mE ==
A aa MU LAA A = > Fi = f ==:
a E ==
vi ==:
Éccus gants „ний ий к 1 =im:
iO dé ES «= т В ВЛЕЧЕТ Е i mir!
ATT ar pi, eam mean i SIE
1 ==
1 ==
ALLÉE. lis, it :
A NAS re MTEL ti i
+ €
A (mans |
I Aaa À
TIRER RES [AL re Tne REE
Viste AN Rates Fi of berry bs ponder a Bo mes
Aer ia Ns stas sn me TC
A co satire 5
> ll II Te caen _
„X - - — i i TTT Е
WY T EE TIO Ti Pa © - = ~ un FS N pra
* Ta Eo И + i ii Н Ë
: Far te 7 Li ; Я I: fT
3 uy [ETE NOLL OREO, bh E AE Е i ' a A Eno
= = т чо won reid: it © o i: Hat aL ILIJO EMIR E Emma
A Press tie ia Bee u ' ID + 7 EF ereeeeneenaees
SCAN PUNCTION Doro r UL киа À \ +, re ii po В ha a
1 \ i _ PI I 5
Ш DO E | UTE ARTE
Th; SPS EE hi ii PET EEE.
Роу e RACE aa ue E 14 ir ER Eee be
x hen E pe Ha j Ï TTT
i m—— 1 j у жет am.
низ NTE A TRAE DEPT 1 SPEED i) { AZ #
Trans STE men Res PIE LR SRE AIDES x bY HE i fi LU М HER.
a nr vee 11 pd ! fata i
iy CASTLE j ELSE it es He
Кона УК 41 1} ; # Th
gr rar en e a sado! ; i; Я a”
Filed a a E one * H ï Hr
man ЧН retire à 7. ge A ЦЕЙ
" 7 i FA A
ENE eMe BE нае A AE RE Г чи Ti Erre e aaa ra tan)
PA {m} pie
A
' i
Ro
]—]——————]——]——;]—;—;—;;—]—]—]—————_—]——— temas ree A = =i —
MA1 00X/150X
W Introduction A
The treadmill has one user manual setting program and 6 preset
programs ( P1- PO). While you running with speed preset programs mode,
the treadmill automatically changes valumn of Speed/incline(only MA150X).
However you can change speed or incline manually at any time you desire.
Before starting the treadmill, ensure the main power switch, which is located at the
front side of machine, is in the "ON" position.
У Quick start 4
When the main power switch is in the "ON" position
and the safety key is inserted into the console, the monitor
window will display a flashing "0:00." Press "START"
to begin "Manual Mode."
Y Program Operation A
Y Quick speed keys „4
Durning workout, the user is able to press any of
desired quick speed key on display to get a specific
speed more quickly.
PROGRAM OPERATION
While turn on power and safety key is inseried, the monitor
display a flashing 0:00 .
1. Select Program: Press ~~ to choose program P1-P6
2. Press MODE to enter. Function window display preset
time 30:00 Press xv to increase or decrease desired
workout time.
3. Press START to begin workout,
THE PAUSE FUNCTION
Pause the treadmill at any time during operation by pressing
"STOP" button once.esume treadmill operation by pressing
the "START" button.
THE RESET FUNCTION
Reset workout program and time by holding "STOP" button for
few seconds until the program window displays "0.00" .Repeat the
above steps to reset desired programs, level and workout time.
NOTE
1.When time read out 99:59 or 00:00, a series of "been"
sound last for 5 seconds and then the motor stop.
2.When the safety key is pulled out in any situation, the
motor stops immediately and the system is reset to
manual setting.
3.The graphic of the workout profiles are printed on the
console. Each overall workout time will be segment into
10 sections.Segment time = overall workout time/10
EX: If overall workout time is set at 10 min, then each
segment will be 1 min each.
TARGET HEART RATE PROGRAM (INCLINE FOR MA150X):
This program automatically modifies the speed and incline to maintain a preset target heart rate.
This target is established in the setup process The chart on this owners manual should be used to determine the
appropriate target heart rate. To set up the target heart rate program, you will need to enter the workout time,
your age, and your target heart rate:
Faas! Increased Performance Range
erobic Training Range
| 4 Weight Loss Traîning Range
IN Heart mate gem
DA TEN EIR er TER
20 25 30 35 40 45 50 55 60 65
AGE
MA100X/150X
Target Heart Rate Program Setup
1.Select Program: Use either "up" or "down" arrows to scroll through the programs until "H1" is shown
on the center display. Then press the "Mode" button.
2.Select Age: Use either "up" or "down" arrows to enter the user age. Then press the "Mode"
button.
3.Set Target Heart Rate: Use either "up” or "down" arrows to set the target heart rate. Then
press "Mode". After a warm-up period, the program will automatically adjust the speed to maintain the
Target Heart Rate (Range From 60 ~180 bpm).
4.Set Target Max Speed:Use either "up" or "down" arrows to set the target max. speed. The speed will
not increase over than max. speed even though pulse is not reach target heart rate yet.
5.Enter Program Time: Use either "up" or "down" arrows to enter the program workout time.
Then press the "Start" button
NOTES: (FOR MA100X)
1. After press "START", there is a warming period for the first 3 minutes to speed
3.0km/hr.
2. After warming up, the program compares actual heart rate and target heart rate
every 12-15 seconds.
3. If the actual heart rate is less than target heart rate, the treadmill increases speed
by 0.2km/h every time. If the actual heart rate reaches target heart rate, the
treadmill decreases speed by 0.4km/h every time.
If the speed increases up to 95% of target speed value , then speed can not be
increased anymore eventhough the actual heart rate is still less than target heart
rate.
4. If it does not read heart rate signal from user in 30 seconds after warming up
period, the treadmill stops and enters into RunkEnd mode.
NOTES: (FOR MA150X)
1. After press "START", there is a warming period for the first 3 minutes to incline
level 5 and speed 3.0km/hr.
2. After warming up, the program compares actual heart rate and target heart rate
every 12~15 seconds.
3. If the actual heart rate is less than target heart rate, the treadmill increases speed
by 0.2km/h every time and increases incline by 1 once changing speed by 5
times. If the actual heart rate reaches target heart rate, the treadmill decreases
speed by 0.4km/h every time and decreases incline by 1 once changing speed by
5 times. |
If the speed increases up to 95% of target speed value , then speed can not be -
increased anymore eventhough the actual heart rate is still less than target heart
rate.
4. If it does not read heart rate signal from user in 30 seconds after warming up
period, the treadmill stops and enters into RunEnd made.
MA100X/150X
Start/Stop:
This will start the treadmill and this will stop the
treadmill. There will also be an emergency stop switch.
(Safety Key)
Mode;
This will select programsflevel selection. This
will switch display data on data window during exercise.
Incline a : (only MATS5OX)
This will select program/level in setting mode before starting.
This will increase the elevation in 1 increment.
Incline : (only MA150X)
This will select program/tevel in setting mode before starting.
This will decrease the elevation in 1 increment.
Speed» :
This will select program/evel in setting mode before starting.
This will increase the speed in 0.1 km/h or 0.1 mph
Speed Ÿ :
This will select program/level in setting mode before starting.
This will decrease the speed in 0.1 km/h or 0.1 mph
Walk, Jog, Run and Sprint
Four quick speed keys = Walk, Jog, Run and Sprint
Walk = 4 km/h or 3 mph
W Button Description |
y Display 4
The display is 3 LED windows with track.
Windows:
1. Incline : 85 (0 level - 12 level)
(Only for MA150X)
2. Data window:
Time:88:88
Distance:88,H58 (km or mile)
Cal: 8888
Pulse: 888
Lap: 4886
Scan: It displays above data ordinally.
3. Speed: §5.8(1-13 km or 0.6-8 mile)
Track:
Count for exercise distance. It is equal to 400
meter or 0.25 mile per lap.
SCAN FUNCTION:
Display ail of function step by step.
Jog = 6 km/h or 4 mph
Run = 8 km/h or 5 mph rene AA ete ee o — veer
. . dre, y ÇA e
Sprint = 10 km or 6 mile e Nal A LA prie, |
п. Wh mfremgiee EY
неа № a \ Y \ i rr Ma 2
© em. AP 7 7 d Fi
= re 1 Na Te: A perra ear - / #
№ | Ea \
М \ 41 j
М 1 00X al, met Ain. 1 ER E BEE aan aia am ee nba ima
+ E AiO SÍ í
A \ | Eee ji
Im € "E as li
L aT À A > ta ol : — НН edad
\ min cn ami or Aa ee TT TET tte FE
M 1 TT ye DU? - y
\ А СЫ | |=!
Ÿ Yo ; a :
L a Ta SOBRE
\ AE
Y X f 5 /
1 3 Н "ko
pu 8 {LX Goo
en E TNT es
ETT \\ сути me wre ee on
; Lo NA LIE se o
+ 4 alles: \ TO A fo’
“ag 4 nes mr \ % \ x TEA %
na - a pe i by à 5
\ \ NA 777
A = he crs Y \ “Wiel pees peg Der Dre
E aw Al Na
MA150X
"e cm
UT ls ET À a
La mT
a ETT J
PRESET PROGRAM
Under preset programs, the preset workout time is 30 minutes. You can adjust the workout time
while in set program mode.
Y MA100/150 4
speed program
Pa P2 РЗ
Intervall 1.5 = 2
Interval2 2 7 A
Interval3 2.5 2 6
Intervald > 7 3
Interval5 3.5 2 10
IntervalG 3 7 8
Interval? 2.5 2 ©
Intervals 2.5 7 4]
Interval9 1.5 2 4
Interval10 1.5 2 2
09345
033dS
dd
Weight Loss E Interval @ Hill Climb
PRESET PROGRAM
Under preset programs, the preset workout time is 30 minutes. You can adjust the workout time
while in set program mode.
P MA100X 4
speed program
P1 P2 P3 P4 PS P6(5km)
LT IL2 1L3| EN L2/L3;ILA|L2LZIL1IL2|L3| LI) L2| L3L1I.21 LS
Intervali | 1.5/2.513.5|2 | 3 | 412 |314 |2 1314 |1 3121314
Толекхуа!2 |2 | 31417 |8 |914 |5 |6 |2 |314 |3 |4 |5 |4 |5 |6
Interval3 |2.513.54.5:2 | 3 |4 |6 |7 18 |8 |9 10| 5 |6 | 7 |5 | 7 |8
Intervald | 3 [4 | 5 |7 | 8 | 9 | 8 | 9 [10 | 8 | 9 110 | 7 | 8 | 9 | 8 | 9 | 10
Interval |3.5/4.55.512 | 3 | 4 110 |1! 12 |6 | 7 |8 | 91101 11| У | 8:39
Interval6 | 3 | 4 |5 |7 | 8 |9 |8 | 9 [10 | 6 | 7 | 8 | Э [10 | 11| 6 |7 8
Interval7 |2.53.54.5 |2 | 314 |6 |7 |8 |4 |5 |6 |6 |7 |8 |5 |6 /
Interval8 |2.5/3.5/4.51 7 | 8 |914 |5 |6 14 |5 |6 |6 |7 |8 |4 |5 |6
Interval9 |1.52.53.5El 2 | 3 |4 |4 | 516 |2 |3 |4 |3 |4 |5 |3 |4 |5
IntervallQ|1.5(25|35;2 | 3 |4 |2 |314 |2 |3 |4 |314 |5 |2 |314
с ® Si
Losas. TELE. tli, Flore, ®t, Sallis,
5km
y MA150X A
speed program incline program
PT P2 РЗ РА PS P6(5km)
L1 1L2 1L3/ L1| L2/1L3 111 112113 LA |L2 |13 1 L1|1L2| LS L1 |L2 | L3
Intervail | 1.5/2.513.5] 2 | 3 | 4 213 1412341123123] 4
Interval2 | 2 | 314 {7 | 819 4 |5 |6 |2 |3 |4 |3 |4 |514 |5 |6
Interval3 | 2.5 3.54.5; 2 | 31 4 61718189 (10 5 16 | 7 | 5 | 7 |8
Interval4 | 3 14 i5:718:9 81911018 | 9 |110 | 7 | 8 | 918 | 9:10
Intervals |3.54.5/55|2 |3 | 4 10 | 112 | 6 |7 |8 | 9 110 | 11| 7 |8 |9
Interval6 | 3 | 4 |5 |7 | 8 |9 8 |9 |10 |6 |7 18 | 9 10/1116 7) 8
Interval? | 2.5/3.5/4.5| 2 | 3|4 6 171,8 |/41:5/6;6;7; 81 5/67
Interval8 2.5/3.5/14.51 7 | 8 |9 |4 |5 |6 |415 |616 |7 |8 |4 |5 |6
Interval9 | 1.5/2.513.5| 2 | 31 4 à 1516 2 |3]|4|/3|4|/ 513 | 4 5
IntervallQ| 1.5/2.513.5] 2 | 3 | 4 2 1314 2) 3|/4|/3] 1415 2 |3 |4
ED 2 Фа) Ps (РЭ es
oo Ямы, Ямы Я, нь
m mf fi =
Skm
Read carefully the following before using your treadmill
+ Always stretch your muscles before exercise program.
Warm up slowly by walking at a slow speed. Increase
workout intensity gradually until you reach your desired
workout pace. gradually to an easy walk, allowing your
heart rate to decrease to normal situation.
+ When start the treadmill, always stand with both feet
on the step-on side rails.
@ When finishing, allow the running beit to slow and come
to a complete stop before stepping off.
@ Wear comfortable, nonrestrictive clothing when using
the treadmill. Never wear anything loose, such as
baggy sweat pants, neckies, loose socks, or jewelry.
Never drape towels on or around the treadmill during
use.
Before completing an exercise
session always
1. Allow time to slow your pace, cool down, reducing
your heart rate to a normal level before completing your
workout.
2. Grasp the handlebars and press the SLOW Speed
button. Slow your pace to an easy walk.
3. Ensure the running belt has come to a complete stop
before exiting the treadmill.
A Warning
Turn off and unplug the treadmill before proceeding with any
maintenance or visual inspections. Failure to do so may
result in serious injury. Note: Failure to perform the required
periodic and preventative maintenance can void your warranty.
@ Always use the handrail when stepping on or off the
treadmill and when changing incline or speed.
@ This treadmill is equipped with a safety key - Always clip
the cord attached to the safety key to a part of your
clothing so the safety key will properly detach from the
computer console, therefore stopping the treadmill.
4 Wear running or walking shoes with high- traction soles.
To avoid injury and unnecessary wear on your treadmill,
be sure your shoes are free of any debris such as gravel
and small rocks.
ZA Warning
If you feel dizzy, nausea, chest pin,or other abnormal
sympoms, stop immediately. Consult a physician before
continuing use.
At the ent of every exercise
session always
1. Remove the Safety Key from the computer console.
2. Use the master power switch to turn the treadmill off.
The master power switch is located at the right side of
frame next to the electrical cord.
3. Always position and store the electrical cord where is
clear from all pathways.
4, Unplug the electrical cord from the electrical outlet. This
is especially important if you are not going to use your
treadmill for extended periods.
5. Wipe all treadmill surfaces with a dry cloth or towel
especially perspiration on the handlebars, control panel,
running belt or other treadmill components.
Y General Cleaning 4
1, Before proceeding, ensure that the treadmill power is off and
that is unplugged from the electrical outlet.
2. To remove dust, use a small vacuum nozzle to carefully
vacuum around all visible components.
3. To remove film or dirt use a slightly damp rag with a mild
cleaning agent sprayed onto the rag only.
4. Be careful not to immerse any treadmill component with any
liquids.
W Cleaning and inspecting the running belt 4
Turn off the power and unplug from electrical outlet. Carefully
position the treadmill on its side. Use a damp cloth to wipe
off the inside of the running belt. Carefully rotate the running
belt by hand to clean the entire inside face. Return treadmill to
its upright position. If running belt edges are frayed, check
the runnin g belt alignment. If seams are splitting, call your
retailer or nearest authorized service center.
VW Aligning the Running Belt „4
Ensure the running belt is centered on your treadmill at all times.
Running style and a non-level surface are two instances that
may cause the belt to drift off center, Minor adjustments to the
two bolts at the rear of the treadmill are necessary when the
belt has drifted off center.
1. Press "START" {o begin running belt, then increase the
treadmills speed to 5 Km/hr (3 M/hr).
2. Stand at the rear of the treadmill to determine which
direction the belt is drifting.
3. 1f the belt drifts to the left, turn the left adjustment bolt with
wrench # 6 one-quarter of a turn clockwise. (See FIG.C)
4. If the belt drifts to the right, turn the right adjustment bolt
with wrench # 6 one-quarter of a turn clockwise.
(See FIG.D)
5. Observe the tracking of the belt for about 30 seconds. Repeat
step 3, 4 and 5 as needed.
W Inspecting Fasteners and Cable A
FIG.C FGD
Check that all fasteners are properly tightened and all
cables are securely in place. To avoid damaging fasteners,
do not over tighten,
Y Storage 4
Store your treadmill in a clean and dry environment. Ensure
the master power switch is off and is unplugged from the
electrical outlet.
y Moving 4
The treadmill has been designed and equipped with wheels for
easy mobility. Before moving, ensure the master power switch
is in the "OFF" position and the power cord is unplugged
from the electrical outlet. Lift the base frame of the treadmill
and then roll the treadmill to the desired position.
PR unning Belt Lubrication М
When you feel the noise of running belt is louder,
please use silicone fluid spray on running beit. It Is
easy and quick. Before proceeding, ensure the
treadmill power is off and unplugged. Fold up the
treadmill to upright position. Loosen the running
belt and then spray silicone on the inner side of
running belt from both sides. Ensure spray entire
running belt. Please see illustration. After spraying,
please align the running belt and adjust the running
belt tension.
MAINTENANCE
Y Foldinglunfolding (Soft Drop Function) À
Fold up A RFA Release |
After the workout session. vou can 4. 7/ You can release the treadmill for .
и 40 the upright position.
fold the treadmill to the upright
position. Lift up the rear end of the
treadmill until the upper folding tube
and lower folding tube are notin
concentic position.
Upper tube and lower tube are not
in concentric position for safety lock.
7/ Ya 1.Push up the frame by hands.
Pushup 2 Kick the lock tube.
3.Lower the treadmill by hands and it will
drop automatically without hand support.
Horizontal Adjustment 4
To fit machine on floor stable, you can
adjust the 2 screws located under the
front of base frame.
1.Lift the machine on one side and then
turn the screw under the front of base
frame.
2 Turn the screw clockwise to make the
screw up.
3.Turn the screw counterclockwise to
make the screw down.
W Trouble shooting with Error codes 4
Electronics continuously runs a self check. If it finds an irregularity, the electronic console will display an error code and stop
normal operation for safety.
Error Gode Description E1 Speed Error E6/E7 Incline Error
Error
Code
MODEL
Trouble shooting
E1:
MA100
MA150
MA100X
MA150X
When E1 is displayed, remove salety key and insert it again to restart treadmili. If ET is still shown on display,
please check the following:
1. Please check all cable connection is well connedted.
2. The treadmill did not move after pressing “Start” and show E1 , please check if there is any part stuck.
3. The treadmill run for few seconds after pressing "Start" but stops, please check if the sensor
{near flywheel of front roller) is loose or defective.
4. Please check wires connected to motor are loose or not,
5. Please contact stores for service if E1 can not be solved.
EG
MA150
When E6 is displayed, remove safety key and insert it again to restart treadmill. If E6 is still shown on display,
please call for service and check the following
1. Please check rediwhite incline cables are well connected on MCB or not,
2. Please call for service to replace part if needed,
EB
Е7:
MA150X
When E6/E7 is displayed , remove safety key and insert it again to restart treadmil! . If E6/E7 is still shown on
display, please check the following or call for service.
1. Reset incline value
(1) When the position of incline is lower than middie level, press " Mode” and incline "up" buttons. Hold both
buttons and the incline will be raised. Release the two buttons till the incline position is up to middle level.
(2) When the position of incline is higher than middie level, press " Mode" and incline "down" buttons. Hold
both buttons and the incline will be reduced. Release the two buttons till the incline position is down to middle level.
Please try it for few times. if you can not get the incline move, please contact stores for service.
Once the incline position is at middle level, please turn off power and re-start. Please see if EG / E7 goes away.
If not, please contact stores for service.
2. Please check if red / white incline cables are well connected to MCB.
3. If the above steps can not reset incline , please contact stores for service.
y Table Of Contents A
MA 150X
Congratulations on the purchase of your new motorized treadmill. To help ensure the
enjoyable and trouble-free operation of your new treadmill, we strongly suggest you read this
manual carefully and follow its recommendations.
B Important Safety Instruction ......... 1 № Preset Program
MAI00/150 ..........ccoonrecocconncnareooos 9
MM Assembly Instruction .................... 2 — MAT0O0OX/150X.............nrescccccve. 10
№ Console Operation 811170777117 ….innccssucssrssesseressrr0une 11
MA100/150 …..….………sesecrersrrsees 4
MALT00X/150X ...............enconcococos 6 E Maimtenance ............e.oneocacccconnes 12
2006/11 (МА! -4)
IMPORTANT SAFETY INSTRUCTIONS
DAN С E В - To reduce the risk of electric shock
Always unplug this appliance from the electrical outlet immediately
after using and before cleaning.
* Use this applince only for its intended use as described in this manual.
Do not use attachment not recommended by the manufacture.
+ To disconnect, turn all controls to the off position, than remove plug
from outlet.
* Connect this appliance to properly grounded outlet only. See
Grounding Instructions.
+ The appliance is intended for household use.
+ When you are not going to use your treadmill ,or when finishing,
please remove the safety key from the console then always position
the safety key where the children can not take.
4 Do not use outdoors.
¢ Always unplug the treadmili from the electrical outlet immediately
after using and before cleaning, assembiing or servicing.
+ Never leave the treadmill unattended when plugged in.Disconnect
by turning off the master power switch and unplugging form outlet.
4 Never operate this treadmill ifit has a damaged cord or plug, is
not working properly, if it has been dropped or damaged or if it has
been exposed to water.
4 Do not operate where aerosol! products are being used or where
oxygen is being administered.
¢ Don't pull the treadmill by its power cord or use the cord as a handle.
+ Keep close supervision if this treadmill is used by, or near children,
persons with disabilities or pets.
* Keep dry. Do not operate this treadmill in wet or moist conditions.
+ Never insert any object into any opening.
+ Before using the treadmill, always warm up your muscles to prevent
the exercise injury.
+ Please unplug the electical cord from the electrical outlet,
and always prevent the children from danger because of
careless touching
+ Keep electric cord away from heated surfaces.
+ Keep hands clear of all moving parts. Never place hands or
feet under the treadmill.
+ Before each use,check that the running belt is aligned and
centered on the treadmill bed and all visible fasteners
on the treadmill are sufficiently tightened and secure.
€ Keep the treadmill on a solid, level surface with sides at least
two feet from any walls, Be sure the area around the treadmill
remains clear during use and has adequate clearance.
NOTE:
Failure to follow these instructions may lead to personal injury
and cause damage to the treadmill. To reduce the risk of burns,
fire,electric shock, please keep the following in mind:
2FEET MIN
2 FEET MIN
Un
i
LEFT $
SIDE -
RIGHT
SIDE
NIE 133 7
ELECTRICAL GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or break down,
grounding provides a path of least resistance for electric current to
reduce the risk of electricshock. This treadmill is equipped with a cord
having equipment grounding connector and a grounding plug. The
plug must be plugged into-an appropriate outlet that is properly installed
and grounded in accordance with all local coades and ordinances.
A Danger
Improper connection of the freadmill. grounding connector
can result in the risk of electric shock. Check with a qualified
electrician, if you are in doubt as to whether the product is properly
grounded. Don't modify the plug provided with the treadmill. If it
won't fit your outlet, have a properly grounded outlet installed by
a qualified electrician
A Warning
Never use extension cords between the treadmill
and wall outlet.
Figure
Grounding methods
GROUNDED
Outlet
LD
TD
GROUNDING
PIN
ZA Warning
After unpacking the fitness equipment, examine it
carefully for possible damage. if there is any damage
or there are missing parts, please contact your retailer
or an authorized repair facility for assistance.
MA100/150/MA100X/150X
ASSEMBLYAINSTRUCTION
Screw attached on machine
This treadmill is shipped with all parts and tools
necessary for assembly. Please read this entire
manual thoroughly before assembling. We recommend
assmbling the treadmill on the shipping carton Ensure
the floor is solid, level and clean.
M10 X 60L (2rcs)
A
screws FAN
MIO X 10t (2Pcs)
®
nylon nut A
M8 X15L (4rcs)
screws à
24.1 X 5/8L (2res)
v
screws Æ)\
Screw packed by poly bag
M8 X 65L(4Pcs)
screws A
TOOL
y Parts À
(A) Frame
Support handle
© Handlebar
®) Console
(Е) PCB cable
(Ez) PCB cable
(F1) Hand pulse cable
(#2) Hand pulse cable
© Left Rack
(H) Right Rack
© Hand pulse
_
Wrench-6mm
Wrench-5mm
—
Wrench