Document

Document
Version: V1.0
DELTA_ASDA-B2_M_EN_20130906
Preface
Thank you very much for purchasing DELTA’s AC servo products.
This manual will be helpful in the installation, wiring, inspection, and operation of Delta AC
servo drive and motor. Before using the product, please read this user manual to ensure
correct use.
You should thoroughly understand all safety precautions (DANGERS, WARNINGS and
STOPS) before proceeding with the installation, wiring and operation. If you do not
understand please contact your local Delta sales representative. Place this user manual in
a safe location for future reference.

Using This Manual
 Contents of this manual
This manual is a user guide that provides the information on how to install, operate
and maintain ASDA-B2 series AC servo drives and ECMA series AC servo motors.
The contents of this manual include the following topics:

Installation of AC servo drives and motors

Configuration and wiring

Trial run steps

Control functions and adjusting methods of AC servo drives

Parameter settings

Communication protocol

Inspection and maintenance

Troubleshooting

Application examples
 Who should use this manual
This manual is intended for the following users:

Those who are responsible for designing

Those who are responsible for installing or wiring

Those who are responsible for operating or programming

Those who are responsible for maintaining or troubleshooting
Revision September 2013
i
Preface
ASDA-B2
 Important precautions
Before using the product, please read this user manual thoroughly to ensure
correct use. Store this manual in a safe and handy place for quick reference
whenever necessary. Always observe the following precautions:

Do not use the product in a potentially explosive environment.

Install the product in a clean and dry location free from corrosive and
inflammable gases or liquids.

Do not connect commercial power to the U, V, W terminals. Failure to
observe this precaution will cause severe damage to the Servo drive.

Ensure that the motor and drive are correctly connected to a ground. The
grounding method must comply with the electrical standard of the country
(Please refer to NFPA 70: National Electrical Code, 2005 Ed.).

Do not disconnect the AC servo drive and motor while the power is ON.

Do not attach, modify or remove wiring while power is applied to the AC
servo drive.

Before starting the operation with a mechanical system connected, make
sure the emergency stop equipment can be energized and work at any time.

Do not touch the drive heat sink or the servo motor during operation, this
may cause serious personnel injury.
PLEASE READ PRIOR TO INSTALLATION FOR SAFETY.
Carefully note and observe the following safety precautions when receiving, inspecting,
installing, operating, maintaining and troubleshooting. The following words, DANGER,
WARNING and STOP are used to mark safety precautions when using the Delta’s servo
product. Failure to observe these precautions may void the warranty!
ASDA-B2 series drives are open type servo drives and must be installed in an NEMA
enclosure such as a protection control panel during operation to comply with the
requirements of the international safety standards. They are provided with precise
feedback control and high-speed calculation function incorporating DSP (Digital Signal
Processor) technology, and intended to drive three-phase permanent magnet synchronous
motors (PMSM) to achieve precise positioning by means of accurate current output
generated by IGBT (Insulated Gate Bipolar Transistor).
ASDA-B2 series drives can be used in industrial applications and for installation in an enduse enclosure that do not exceed the specifications defined in the ASDA-B2 series user
manual (Drives, cables and motors are for use in a suitable enclosure with a minimum of a
UL50 type 1 or NEMA 250 Type 1 rating).
ii
Revision September 2013
ASDA-B2
Preface
The words, DANGER, WARNING and STOP, have the following meaning:
Indicates a potentially hazardous situation and if not avoided, may result in
serious injury or death.
Indicates a potentially hazardous situation and if not avoided, may result in minor
to moderate injury or serious damage to the product.
Indicates an improper action that it is not recommended. Doing so may cause
damage or malfunction.
Unpacking Check

Please ensure that both the servo drive and motor are correctly matched for
size (power rating). Failure to observe this precaution may cause fire, seriously
damage to the drive / motor or cause personal injury.
Installation

Do not install the product in a location that is outside the stated specification
for the drive and motor. Failure to observe this caution may result in electric
shock, fire, or personal injury.
Wiring

Connect the ground terminals to a class-3 ground (Ground resistance should
not exceed 100 Ω). Improper grounding may result in electric shock or fire.
 Do not connect any power supplies to the U, V, W terminals. Failure to observe
this precaution may result in serious injury, damage to the drive or fire.
 Ensure that all screws, connectors and wire terminations are secure on the
power supply, servo drive and motor. Failure to observe this caution may
result in damage, fire or personal injury.
Operation

Before starting the operation with a mechanical system connected, change the
drive parameters to match the user-defined parameters of the mechanical
system. Starting the operation without matching the correct parameters may
result in servo drive or motor damage, or damage to the mechanical system.
 Ensure that the emergency stop equipment or device is connected and
working correctly before operating the motor that is connected to a mechanical
system.

Do not approach or touch any rotating parts (e.g. shaft) while the motor is
running. Failure to observe this precaution may cause serious personal injury.

In order to prevent accidents, the initial trial run for servo motor should be
conducted under no load conditions (separate the motor from its couplings
and belts).
 For the initial trial run, do not operate the servo motor while it is connected to
its mechanical system. Connecting the motor to its mechanical system may
cause damage or result in personal injury during the trail run. Connect the
servo motor once it has successfully completed a trail run.
 Caution: Please perform trial run without load first and then perform trial run
with load connected. After the servo motor is running normally and regularly
without load, then run servo motor with load connected. Ensure to perform trial
run in this order to prevent unnecessary danger.
Revision September 2013
iii
Preface
ASDA-B2

Do not touch either the drive heat sink or the motor during operation as they
may become hot and personal injury may result.
Maintenance and Inspection






Do not touch any internal or exposed parts of servo drive and servo motor as
electrical shock may result.
Do not remove the operation panel while the drive is connected to an electrical
power source otherwise electrical shock may result.
Wait at least 10 minutes after power has been removed before touching any
drive or motor terminals or performing any wiring and/or inspection as an
electrical charge may still remain in the servo drive and servo motor with
hazardous voltages even after power has been removed.
Do not disassemble the servo drive or motor as electric shock may result.
Do not connect or disconnect wires or connectors while power is applied to
the drive and motor.
Only qualified personnel who have electrical knowledge should conduct
maintenance and inspection.
Main Circuit Wiring

Install the encoder cables in a separate conduit from the motor power cables to
avoid signal noise. Separate the conduits by 30cm (11.8inches) or more.
 Use multi-stranded twisted-pair wires or multi-core shielded-pair wires for
signal, encoder (PG) feedback cables. The maximum length of command input
cable is 3m (9.84ft.) and the maximum length of encoder (PG) feedback cables
is 20m (65.62ft.).
 As a charge may still remain in the drive with hazardous voltages even after
power has been removed, be sure to wait at least 10 minutes after power has
been removed before performing any wiring and/or inspection.

It is not recommended to frequently power the drive on and off. Do not turn the
drive off and on more than once per minute as high charging currents within
the internal capacitors may cause damage.
Main Circuit Terminal Wiring





Please perform the wiring after the terminal blocks are all removed from the
drive.
Insert only one wire into one terminal on the terminal block.
When inserting wires, please ensure that the conductors are not shorted to
adjacent terminals or wires.
Ensure to double check the wiring before applying power to the drive.
If the wiring is in error, perform the wiring again with proper tools. Never use
force to remove the terminals or wires. Otherwise, it may result in malfunction
or damage.
NOTE
1) In this manual, actual measured values are in metric units. Dimensions in (imperial units) are
for reference only. Please use metric units for precise measurements.
2) The content of this manual may be revised without prior notice. Please consult our distributors
or download the most updated version at http://www.delta.com.tw/industrialautomation.
iv
Revision September 2013
Table of Contents
Chapter 1 Unpacking Check and Model Explanation ........................................... 1-1
1.1 Unpacking Check ............................................................................................ 1-1
1.2 Model Explanation ........................................................................................... 1-2
1.2.1 Nameplate Information ........................................................................... 1-2
1.2.2 Model Name Explanation ....................................................................... 1-4
1.3 Servo Drive and Servo Motor Combinations ................................................... 1-6
1.4 Servo Drive Features ...................................................................................... 1-7
1.5 Control Modes of Servo Drive ......................................................................... 1-8
Chapter 2 Installation and Storage......................................................................... 2-1
2.1 Installation Notes ............................................................................................. 2-1
2.2 Storage Conditions .......................................................................................... 2-1
2.3 Installation Conditions ..................................................................................... 2-2
2.4 Installation Procedure and Minimum Clearances ............................................ 2-3
2.5 Circuit Interrupter and Fuse Current Recommended Value ............................ 2-5
2.6 EMI Filter Selection ......................................................................................... 2-6
2.7 Regenerative Resistor ..................................................................................... 2-8
Chapter 3 Connections and Wiring ........................................................................ 3-1
3.1 Connections .................................................................................................... 3-1
3.1.1 Connecting to Peripheral Devices .......................................................... 3-1
3.1.2 Servo Drive Connectors and Terminals .................................................. 3-2
Revision September 2013
v
Table of Contents
ASDA-B2
3.1.3 Wiring Methods ...................................................................................... 3-5
3.1.4 Motor Power Cable Connector Specifications ........................................ 3-7
3.1.5 Encoder Connector Specifications ......................................................... 3-9
3.1.6 Cable Specifications for Servo Drive ...................................................... 3-13
3.2 Basic Wiring .................................................................................................... 3-15
3.2.1 400W and below Models ........................................................................ 3-15
3.2.2 750W Model ........................................................................................... 3-16
3.2.3 1kW~1.5kW Models ............................................................................... 3-17
3.2.4 2kW~3kW Models .................................................................................. 3-18
3.3 Input / Output Interface Connector - CN1 ........................................................ 3-19
3.3.1 CN1 Terminal Identification .................................................................... 3-19
3.3.2 Signals Explanation of Connector - CN1 ................................................ 3-21
3.3.3 User-defined DI and DO signals ............................................................. 3-29
3.3.4 Wiring Diagrams of I/O Signals - CN1 .................................................... 3-36
3.4 Encoder Connector - CN2 ............................................................................... 3-37
3.5 Serial Communication Connector - CN3 ......................................................... 3-40
3.6 Analog Monitor Output Connector - CN5 ......................................................... 3-41
3.7 Standard Connection Example ........................................................................ 3-42
3.7.1 Position (PT) Control Mode .................................................................... 3-42
3.7.2 Speed Control Mode .............................................................................. 3-43
3.7.3 Torque Control Mode ............................................................................. 3-44
Chapter 4 Display and Operation ........................................................................... 4-1
4.1 Description of Digital Keypad .......................................................................... 4-1
vi
Revision September 2013
ASDA-B2
Table of Contents
4.2 Display Flowchart ............................................................................................ 4-2
4.3 Status Display ................................................................................................. 4-4
4.3.1 Save Setting Display .............................................................................. 4-4
4.3.2 Abort Setting Display .............................................................................. 4-4
4.3.3 Fault Message Display ........................................................................... 4-4
4.3.4 Polarity Setting Display .......................................................................... 4-4
4.3.5 Monitor Setting Display .......................................................................... 4-5
4.4 General Function Operation ............................................................................ 4-8
4.4.1 Fault Code Display Operation ................................................................ 4-8
4.4.2 JOG Operation ....................................................................................... 4-9
4.4.3 Force Output Control Operation ............................................................. 4-10
4.4.4 DI Diagnosis Operation .......................................................................... 4-12
4.4.5 DO Diagnosis Operation......................................................................... 4-13
Chapter 5 Trial Run and Tuning Procedure ........................................................... 5-1
5.1 Inspection without Load................................................................................... 5-1
5.2 Applying Power to the Drive ............................................................................ 5-3
5.3 JOG Trial Run without Load ............................................................................ 5-7
5.4 Speed Trial Run without Load ......................................................................... 5-9
5.5 Tuning Procedure ............................................................................................ 5-11
5.5.1 Tuning Flowchart .................................................................................... 5-12
5.5.2 Load Inertia Estimation Flowchart .......................................................... 5-13
5.5.3 Auto Mode Tuning Flowchart.................................................................. 5-14
5.5.4 Semi-Auto Mode Tuning Flowchart ........................................................ 5-15
Revision September 2013
vii
Table of Contents
ASDA-B2
5.5.5 Limit of Load Inertia Estimation .............................................................. 5-17
5.5.6 Mechanical Resonance Suppression Method ........................................ 5-19
5.5.7 Relationship between Tuning Modes and Parameters ........................... 5-20
5.5.8 Gain Adjustment in Manual Mode .......................................................... 5-21
Chapter 6 Control Modes of Operation .................................................................. 6-1
6.1 Control Modes of Operation ............................................................................ 6-1
6.2 Position Control Mode ..................................................................................... 6-2
6.2.1 Command Source of Position (PT) Control Mode .................................. 6-2
6.2.2 Structure of Position Control Mode ......................................................... 6-6
6.2.3 Electronic Gear Ratio ............................................................................. 6-7
6.2.4 Low-pass Filter ....................................................................................... 6-9
6.2.5 Position Loop Gain Adjustment .............................................................. 6-10
6.3 Speed Control Mode ....................................................................................... 6-12
6.3.1 Command Source of Speed Control Mode ............................................. 6-12
6.3.2 Structure of Speed Control Mode ........................................................... 6-14
6.3.3 Smoothing Strategy of Speed Control Mode .......................................... 6-15
6.3.4 Analog Speed Input Scaling ................................................................... 6-19
6.3.5 Timing Chart of Speed Control Mode ..................................................... 6-20
6.3.6 Speed Loop Gain Adjustment................................................................. 6-20
6.3.7 Resonance Suppression ........................................................................ 6-27
6.4 Torque Control Mode ...................................................................................... 6-35
6.4.1 Command Source of Torque Control Mode ............................................ 6-35
6.4.2 Structure of Torque Control Mode .......................................................... 6-36
viii
Revision September 2013
ASDA-B2
Table of Contents
6.4.3 Smoothing Strategy of Torque Control Mode ......................................... 6-37
6.4.4 Analog Torque Input Scaling .................................................................. 6-38
6.4.5 Timing Chart of Torque Control Mode .................................................... 6-39
6.5 Control Mode Selection ................................................................................... 6-40
6.5.1 Speed / Position Control Mode Selection ............................................... 6-40
6.5.2 Speed / Torque Control Mode Selection ................................................ 6-41
6.5.3 Torque / Position Control Mode Selection .............................................. 6-41
6.6 Others ............................................................................................................. 6-42
6.6.1 Speed Limit ............................................................................................ 6-42
6.6.2 Torque Limit ........................................................................................... 6-42
6.6.3 Analog Monitor ....................................................................................... 6-43
6.6.4 Electromagnetic Brake ........................................................................... 6-47
Chapter 7 Parameters.............................................................................................. 7-1
7.1 Definition ......................................................................................................... 7-1
7.2 Parameter Summary ....................................................................................... 7-2
7.3 Detailed Parameter Listings ............................................................................ 7-10
Group 0: P0-xx Monitor Parameters .................................................................. 7-10
Group 1: P1-xx Basic Parameters ..................................................................... 7-21
Group 2: P2-xx Extension Parameters .............................................................. 7-49
Group 3: P3-xx Communication Parameters ..................................................... 7-78
Group 4: P4-xx Diagnosis Parameters .............................................................. 7-83
Table 7.1 Input Function Definition (DI) ............................................................. 7-93
Table 7.2 Output Function Definition (DO)......................................................... 7-99
Revision September 2013
ix
Table of Contents
ASDA-B2
Chapter 8 MODBUS Communications ................................................................... 8-1
8.1 Communication Hardware Interface ................................................................ 8-1
8.2 Communication Parameter Settings ................................................................ 8-4
8.3 MODBUS Communication Protocol................................................................. 8-7
8.4 Communication Parameter Write-in and Read-out .......................................... 8-16
Chapter 9 Troubleshooting ..................................................................................... 9-1
9.1 Fault Messages Table ..................................................................................... 9-1
9.2 Potential Cause and Corrective Actions .......................................................... 9-3
9.3 Clearing Faults ................................................................................................ 9-12
Chapter 10 Specifications ....................................................................................... 10-1
10.1 Specifications of Servo Drives (ASDA-B2 Series) ......................................... 10-1
10.2 Specifications of Servo Motors (ECMA Series) ............................................. 10-4
10.3 Servo Motor Speed-Torque Curves ............................................................... 10-8
10.4 Overload Characteristics ............................................................................... 10-9
10.5 Dimensions of Servo Drives .......................................................................... 10-11
10.6 Dimensions of Servo Motors ......................................................................... 10-15
Appendix A Accessories ........................................................................................ A-1
Appendix B Maintenance and Inspection.............................................................. B-1
x
Revision September 2013
ASDA-B2
Table of Contents
About this Manual…
User Information
Be sure to store this manual in a safe place.
Due to constantly growing product range, technical improvement, alteration or changed
texts, figures and diagrams, we reserve the right to make information changes within this
manual without prior notice.
Coping or reproducing any part of this manual, without written consent of Delta Electronics
Inc. is prohibited.
Technical Support and Service
You are welcome to contact our Technical Support Team at the below numbers or visit our
web site (http://www.delta.com.tw/industrialautomation/) if you need technical support,
service, information, or if you have any questions in the use of this product. We look
forward to serving your needs and are willing to offer our best support and service to you.
ASIA
DELTA ELECTRONICS, INC.
JAPAN
Taoyuan Plant 3
DELTA ELECTRONICS (JAPAN), INC.
No.18, Xinglong Rd.,
Tokyo Office
Taoyuan City, Taoyuan County 33068,
DELTA SHIBADAIMON BUILDING
TAIWAN, R.O.C.
2-1-14 SHIBADAIMON, MINATO-KU,
TEL: 886-3-362-6301
TOKYO, 105-0012, JAPAN
FAX: 886-3-362-7267
TEL: 81-3-5733-1111
FAX: 81-3-5733-1211
NORTH/SOUTH AMERICA
DELTA PRODUCTS CORPORATION (USA)
EUROPE
Raleigh Office
DELTRONICS (THE NETHERLANDS) B.V.
P.O. BOX 12173
Eindhoven Office
5101 DAVIS DRIVE,
DE WITBOGT 15, 5652 AG EINDHOVEN,
RESEARCH TRIANGLE PARK,
NC
THE NETHERLANDS
27709, U.S.A.
TEL: 31-40-259-2850
TEL: 1-919-767-3813
FAX: 31-40-259-2851
FAX: 1-919-767-3969
Revision September 2013
xi
Table of Contents
ASDA-B2
This page is intentionally left blank.
xii
Revision September 2013
Chapter 1 Unpacking Check and
Model Explanation
1.1 Unpacking Check
After receiving the AC servo drive, please check for the following:
 Ensure that the product is what you have ordered.
Verify the part number indicated on the nameplate corresponds with the part number of
your order (Please refer to Section 1.2 for details about the model explanation).
 Ensure that the servo motor shaft rotates freely.
Rotate the motor shaft by hand; a smooth rotation will indicate a good motor. However,
a servo motor with an electromagnetic brake can not be rotated manually.
 Check for damage.
Inspect the unit to insure it was not damaged during shipment.
 Check for loose screws.
Ensure that all necessary screws are tight and secure.
If any items are damaged or incorrect, please inform the distributor whom you purchased
the product from or your local Delta sales representative.
A complete and workable AC servo system should include the following parts:
Part I : Delta standard supplied parts
(1)
Servo drive
(2)
Servo motor
(3)
5 PIN Terminal Block (for L1c, L2c, R, S, T)
(4)
3 PIN Terminal Block (for U, V, W)
(5)
4 PIN Terminal Block (for P , D, C,
(6)
One operating lever (for wire to terminal block insertion)
(7)
One jumper bar (installed at pins P and D of the 3 PIN Terminal Block for P , D, C)
(8)
Instruction Sheets
Revision September 2013
)
1-1
Chapter 1 Unpacking Check and Model Explanation
ASDA-B2
Part II : Optional parts (Refer to Appendix A)
(1)
One power cable, which is used to connect servo motor to U, V, W terminals of
servo drive. This power cable includes a green grounding cable. Please connect the
green grounding cable to the ground terminal of the servo drive.
(2)
One encoder cable, which is used to connect the encoder of servo motor to the
CN2 terminal of servo drive.
(3)
CN1 Connector: 4 PIN Connector (3M type analog product)
(4)
CN2 Connector: 9 PIN Connector (3M type analog product)
(5)
CN3 Connector: 6 PIN Connector (IEEE1394 analog product)
1.2 Model Explanation
1.2.1 Nameplate Information
ASDA-B2 Series Servo Drive

Nameplate Explanation

Serial Number Explanation
ASMT Series Servo Motor

1-2
Nameplate Explanation
Revision September 2013
ASDA-B2

Chapter 1 Unpacking Check and Model Explanation
Serial Number Explanation
Revision September 2013
1-3
Chapter 1 Unpacking Check and Model Explanation
ASDA-B2
1.2.2 Model Name Explanation
ASDA-B2 Series Servo Drive
A S D - B 2 - 0 4 2 1 -B
Model Type
Input Voltage and Phase
21: 220V 1 phase
23: 220V 3 phase
Rated Power Input
01: 100W
20: 2kW
02: 200W
30: 3kW
04: 400W
07: 750W
10: 1kW
15: 1.5kW
Product Series
B2
Product Name
AC SERVO Drive
1-4
Revision September 2013
ASDA-B2
Chapter 1 Unpacking Check and Model Explanation
ECMA Series Servo Motor
E C M A - C 1 0 6 0 2 E S
Standard Shaft Diameter: S
Specific Shaft Diameter: 3=42mm, 7=14mm
w/o
with
Diameter
and
Brake
Brake
w/o
Brake
w/o Oil
w/o Oil
with Oil
Oil Seal
Seal
Seal
Seal
With
Brake
With Oil
Seal
(with fixed
screw holes)
A
B
C
D
Keyway
E
F
G
H
P
Q
R
S
Type of Shaft
Round Shaft
Keyway
(with fixed
screw holes)
Rated Power Output
01:100W 05:500W
02:200W 06:600W
03:300W 07:700W
04:400W 09:900W
10:1.0kW
15:1.5kW
20:2.0kW
30:3.0kW
Motor Frame Size
04:40mm 09:86mm 18:180mm
06:60mm 10:100mm
08:80mm 13:130mm
Name of the Series
Rated Voltage and Rated Speed
C = 220V/3,000 rpm; E = 220V/2,000 rpm;
F = 220V/1,500 rpm; G = 220V/1,000 rpm;
Encoder Type
1: Incremental, 20-bit
2: Incremental, 17-bit
M: Magnetic encoder, 13-bit
Servo Type
A: AC Servo
Product Name
ECM: Electronic
Commutation Motor
Revision September 2013
1-5
Chapter 1 Unpacking Check and Model Explanation
ASDA-B2
1.3 Servo Drive and Servo Motor Combinations
The table below shows the possible combination of Delta ASDA-B2 series servo drives
and ECMA series servo motors. The boxes () in the model names are for optional
configurations. (Please refer to Section 1.2 for model explanation)
Power
Servo Drive
100W
ASD-B2-0121-
ECMA-C20401S(S=8mm)
200W
ASD-B2-0221-
ECMA-C20602S(S=14mm)
ASD-B2-0421-
ECMA-C20604S (S=14mm)
ECMA-CM0604S (S=14mm)
ECMA-C208047 (7=14mm)
ECMA-E21305S (S=22mm)
ECMA-G21303S (S=22mm)
ASD-B2-0721-
ECMA-C20807S (S=19mm)
ECMA-C20907S (S=16mm)
ECMA-G21306S (S=22mm)
ECMA-GM1306S (S=22mm)
1000W
ASD-B2-1021-
ECMA-C21010S (S=22mm)
ECMA-C20910S (S=16mm)
ECMA-E21310S (S=22mm)
ECMA-G21309S (S=22mm)
ECMA-GM1309S (S=22mm)
1500W
ASD-B2-1521-
ECMA-E21315S (S=22mm)
2000W
ASD-B2-2023-
ECMA-C21020S (S=22mm)
ECMA-E21320S (S=22mm)
ECMA-E21820S (S=35mm)
3000W
ASD-B2-3023-
ECMA-E21830S (S=35mm)
ECMA-F21830S (S=35mm)
400W
750W
Servo Motor
The servo drives shown in the above table are designed for use in combination with the
specific servo motors. Check the specifications of the drives and motors you want to use.
Also, please ensure that both the servo drive and motor are correctly matched for size
(power rating). If the power of motor and drive is not within the specifications, the drive
and motor may overheat and servo alarm would be activated. For the detail specifications
of servo drives and motors, please refer to Chapter 11 “Specifications”.
The drives shown in the above table are designed according to the three multiple of rated
current of motors shown in the above table. If the drives which are designed according to
the six multiple of rated current of motors are needed, please contact our distributors or
your local Delta sales representative.
1-6
Revision September 2013
ASDA-B2
Chapter 1 Unpacking Check and Model Explanation
1.4 Servo Drive Features
Revision September 2013
1-7
Chapter 1 Unpacking Check and Model Explanation
ASDA-B2
1.5 Control Modes of Servo Drive
The Delta Servo provides six single and five dual modes of operation.
Their operation and description is listed in the following table.
Mode
External Position Control
Speed Control
Internal Speed Control
Code
P
External Position control mode for the servo motor is
achieved via an external pulse command.
S
(External / Internal) Speed control mode for the servo
motor can be achieved via parameters set within the
controller or from an external analog -10 ~ +10 VDC
command. Control of the internal speed mode is via
the Digital Inputs (DI). (A maximum of three speeds
can be stored internally).
Sz
Internal Speed control mode for the servo motor is
only achieved via parameters set within the controller.
Control of the internal speed mode is via the Digital
Inputs (DI). (A maximum of three speeds can be
stored internally).
T
(External / Internal) Torque control mode for the servo
motor can be achieved via parameters set within the
controller or from an external analog -10 ~ +10 VDC
command. Control of the internal torque mode is via
the Digital Inputs (DI). (A maximum of three torque
levels can be stored internally).
Tz
Internal Torque control mode for the servo motor is
only achieved via parameters set within the controller.
Control of the internal torque mode is via the Digital
Inputs (DI). (A maximum of three torque levels can be
stored internally).
S-P
Either S or P control mode can be selected via the
Digital Inputs (DI)
T-P
Either T or P control mode can be selected via the
Digital Inputs (DI)
S-T
Either S or T control mode can be selected via the
Digital Inputs (DI)
Single
Mode
Torque Control
Internal Torque Control
Dual Mode
Description
The above control modes can be accessed and changed via parameter P1-01. Enter the
new control mode via P1-01 then switch the main power to the servo drive OFF then ON.
The new control mode will only be valid after the drives main power is switched OFF then
ON. Please see safety precautions on page iii (switching drive off/on multiple times).
1-8
Revision September 2013
Chapter 2 Installation and Storage
2.1 Installation Notes
Please pay close attention to the following installation notes:
 Do not bend or strain the connection cables between servo drive and motor.
 When mounting the servo drive, make sure to tighten all screws to secure the drive in
place.
 If the servo motor shaft is coupled directly to a rotating device ensure that the
alignment specifications of the servo motor, coupling, and device are followed. Failure
to do so may cause unnecessary loads or premature failure to the servo motor.
 If the length of cable connected between servo drive and motor is more than 20m,
please increase the wire gauge of the encoder cable and motor connection cable
(connected to U, V, W terminals).
 Make sure to tighten the screws for securing motor.
2.2 Storage Conditions
The product should be kept in the shipping carton before installation. In order to retain the
warranty coverage, the AC servo drive should be stored properly when it is not to be used
for an extended period of time. Some storage suggestions are:
 Store in a clean and dry location free from direct sunlight.
 Store within an ambient temperature range of -20°C to +65°C (-4°F to 149°F).
 Store within a relative humidity range of 0% to 90% and non-condensing.
 Do not store in a place subjected to corrosive gases and liquids.
 Store in original packaging and placed on a solid surface.
Revision September 2013
2-1
ASDA-B2
Chapter 2 Installation and Storage
2.3 Installation Conditions
Operating Temperature
ASDA-B2 Series Servo Drive
:
0°C to 55°C (32°F to 131°F)
ECMA Series Servo Motor :
0°C to 40°C (32°F to 104°F)
The ambient temperature of servo drive should be under 45°C (113°F) for long-term
reliability.
If the ambient temperature of servo drive is greater than 45°C (113°F), please install the
drive in a well-ventilated location and do not obstruct the airflow for the cooling fan.
Caution
The servo drive and motor will generate heat. If they are installed in a control panel, please
ensure sufficient space around the units for heat dissipation.
Pay particular attention to vibration of the units and check if the vibration has impacted the
electric devices in the control panel. Please observe the following precautions when
selecting a mounting location. Failure to observe the following precautions may void
the warranty!
 Do not mount the servo drive or motor adjacent to heat-radiating elements or in direct
sunlight.
 Do not mount the servo drive or motor in a location subjected to corrosive gases,
liquids, airborne dust or metallic particles.
 Do not mount the servo drive or motor in a location where temperatures and humidity
will exceed specification.
 Do not mount the servo drive or motor in a location where vibration and shock will
exceed specification.
 Do not mount the servo drive or motor in a location where it will be subjected to high
levels of electromagnetic radiation.
2-2
Revision September 2013
ASDA-B2
Chapter 2 Installation and Storage
2.4 Installation Procedure and Minimum Clearances
Installation Procedure
Incorrect installation may result in a drive malfunction or premature failure of the drive and
or motor. Please follow the guidelines in this manual when installing the servo drive and
motor.
The ASDA-B2 servo drives should be mounted perpendicular to the wall or in the control
panel. In order to ensure the drive is well ventilated, ensure that the all ventilation holes
are not obstructed and sufficient free space is given to the servo drive. Do not install the
drive in a horizontal position or malfunction and damage will occur.
Drive Mounting
The ASDA-B2 servo drives must be back mounted vertically on a dry and solid surface
such as a NEMA enclosure. A minimum spacing of two inches must be maintained above
and below the drive for ventilation and heat dissipation. Additional space may be
necessary for wiring and cable connections. Also, as the drive conducts heat away via the
mounting, the mounting plane or surface should not conduct heat into the drive from
external sources
Motor Mounting
The ECMA servo motors should be mounted firmly to a dry and solid mounting surface to
ensure maximum heat transfer for maximum power output and to provide a good ground.
For the dimensions and weights specifications of servo drive or motor, please refer to
Chapter 11 “Specifications".
Minimum Clearances
Install a fan to increase ventilation to avoid ambient temperatures that exceed the
specification. When installing two or more drives adjacent to each other please follow the
clearances as shown in the following diagram.
Revision September 2013
2-3
Chapter 2 Installation and Storage
ASDA-B2
 Minimum Clearances
 Side by Side Installation
2-4
Revision September 2013
ASDA-B2
Chapter 2 Installation and Storage
2.5 Circuit Interrupter and Fuse Current Recommended Value

Caution: Please use circuit interrupter and fuse which are recognized by and
comply with the UL or CSA standards.
Servo Drive Model
Recommended Breaker
Recommended Fuse (Class T)
Operation Mode
General
General
ASD-B2-0121-B
5A
5A
ASD-B2-0221-B
5A
6A
ASD-B2-0421-B
10A
10A
ASD-B2-0721-B
10A
20A
ASD-B2-1021-B
15A
25A
ASD-B2-1521-B
20A
40A
ASD-B2-2023-B
30A
50A
ASD-B2-3023-B
30A
70A
NOTE
1) When using a GFCI (Ground Fault Circuit Interrupter), select a current sensor with sensitivity of equal to
or more than 200mA, and not less than 0.1-second detection time to avoid nuisance tripping.
Revision September 2013
2-5
ASDA-B2
Chapter 2 Installation and Storage
2.6 EMI Filter Selection
AC Servo Drive - EMI Filter Cross Reference
Item
Power
Servo Drive Model
1
100W
2
EMI Filter Model
FootPrint
1PH
3PH
ASD-B2-0121-B
RF007S21AA
RF022M43AA
N
200W
ASD-B2-0221-B
RF007S21AA
RF022M43AA
N
3
400W
ASD-B2-0421-B
RF007S21AA
RF022M43AA
N
4
750W
ASD-B2-0721-B
RF007S21AA
RF022M43AA
N
5
1000W
ASD-B2-1021-B
RF015B21AA
RF075M43BA
N
6
1500W
ASD-B2-1521-B
RF015B21AA
RF075M43BA
N
7
2000W
ASD-B2-2023-B
-
RF037B43BA
N
8
3000W
ASD-B2-3023-B
-
RF037B43BA
N
Installation
All electrical equipment, including AC servo drives, will generate high-frequency/lowfrequency noise and will interfere with peripheral equipment by radiation or conduction
when in operation. By using an EMI filter with correct installation, much of the interference
can be eliminated. It is recommended to use Delta’s EMI filter to have the best interference
elimination performance.
We assure that it can comply with following rules when AC servo drive and EMI filter are
installed and wired according to user manual:
 EN61000-6-4 (2001)
 EN61800-3 (2004) PDS of category C2
 EN55011+A2 (2007) Class A Group 1
General Precaution
To ensure the best interference elimination performance when using Delta’s EMI filter,
please follow the guidelines in this user manual to perform wiring and/or installation. In
addition, please also observe the following precautions:
 EMI filter and AC servo drive should be installed on the same metal plate.
 Please install AC servo drive on same footprint with EMI filter or install EMI filter as
close as possible to the AC servo drive.
 All wiring should be as short as possible.
 Metal plate should be grounded.
 The cover of EMI filter and AC servo drive or grounding should be fixed on the metal
2-6
Revision September 2013
ASDA-B2
Chapter 2 Installation and Storage
plate and the contact area should be as large as possible.
Choose Suitable Motor Cable and Precautions
Improper installation and choice of motor cable will affect the performance of EMI filter. Be
sure to observe the following precautions when selecting motor cable.
 Use the cable with shielding (double shielding is the best).
 The shielding on both ends of the motor cable should be grounded with the minimum
length and maximum contact area.
 Remove any paint on metal saddle for good ground contact with the plate and
shielding (Please refer to Figure 1 below).
 The connection between the metal saddle and the shielding on both ends of the motor
cable should be correct and well installed. Please refer to Figure 2 on next page for
correct wiring method.
Figure 1
Saddle on both ends
Saddle on one end
Figure 2
Revision September 2013
2-7
ASDA-B2
Chapter 2 Installation and Storage
2.7 Regenerative Resistor
Built-in Regenerative Resistor
When the output torque of servo motor in reverse direction of motor rotation speed, it
indicates that there is a regenerative power returned from the load to the servo drive. This
power will be transmitted into the capacitance of DC Bus and result in rising voltage. When
the voltage has risen to some high voltage, the servo system need to dissipate the extra
energy by using a regenerative resistor. ASDA-B2 series servo drive provides a built-in
regenerative resistor and the users also can connect to external regenerative resistor if
more regenerative capacity is needed.
The following table shows the specifications of the servo drive’s built-in regenerative
resistor and the amount of regenerative power (average value) that it can process.
Built-in Regenerative Resistor Specifications
Servo Drive
(kW)
Resistance (Ohm)
(parameter P1-52)
Capacity (Watt)
(parameter P1-53)
Regenerative Power
processed by built-in
regenerative resistor
(Watt) *1
Min. Allowable
Resistance (Ohm)
0.1
-
-
-
60
0.2
-
-
-
60
0.4
100
60
30
60
0.75
100
60
30
60
1.0
40
60
30
30
1.5
40
60
30
30
2.0
20
100
50
15
3.0
20
100
50
15
*1 Regenerative Power Calculation: The amount of regenerative power (average value)
that can be processed is rated at 50% of the capacity of the servo drive's built-in
regenerative resistor. The regenerative power calculation method of external regenerative
resistor is the same.
When the regenerative power exceeds the processing capacity of the servo drive, install
an external regenerative resistor. Please pay close attention on the following notes when
using a regenerative resistor.
1. Make sure that the settings of resistance (parameter P1-52) and capacity (parameter
P1-53) is set correctly.
2. When the users want to install an external regenerative resistor, ensure that its
resistance value is the same as the resistance of built-in regenerative resistor. If
combining multiple small-capacity regenerative resistors in parallel to increase the
regenerative resistor capacity, make sure that the resistance value of the
regenerative resistor should comply with the specifications listed in the above table.
3. In general, when the amount of regenerative power (average value) that can be
2-8
Revision September 2013
ASDA-B2
Chapter 2 Installation and Storage
processed is used at or below the rated load ratio, the resistance temperature will
increase to 120°C or higher (on condition that when the regeneration continuously
occurred). For safety reasons, forced air cooling is good way that can be used to
reduce the temperature of the regenerative resistors. We also recommend the users
to use the regenerative resistors with thermal switches. As for the load
characteristics of the regenerative resistors, please check with the manufacturer.
External Regenerative Resistor
When using external regenerative resistor, connect it to P and C, and make sure the circuit
between P and D is open. We recommend the users should use the external regenerative
resistor that the resistance value following the above table (Built-in Regenerative Resistor
Specifications). We ignore the dissipative power of IGBT (Insulated Gate Bipolar
Transistor) in order to let the users easily calculate the capacity of regenerative resistor. In
the following sections, we will describe Regenerative Power Calculation Method and
Simple Calculation Method for calculating the regenerative power capacity of external
regenerative resistors.
(1) Regenerative Power Calculation Method
(a) Without Load
When there is no external load torque, if the servo motor repeats operation, the
returned regenerative power generated when braking will transmitted into the
capacitance of DC bus. After the capacitance voltage exceeds some high value,
regenerative resistor can dissipate the remained regenerative power. Use the table and
procedure described below to calculate the regenerative power.
Servo Motor
Rotor Inertia
2
J (× 10-4kg.m )
Regenerative power
from empty load
3000r/min to stop
Eo (joule)
Max. regenerative
power of
capacitance
Ec(joule)
0.1
ECMA-C20401
0.037
0.18
3
0.2
ECMA-C20602
0.177
0.87
4
0.4
ECMA-C20604
ECMA-C20804
0.277
0.68
1.37
3.36
8
0.75 ECMA-C20807
1.13
5.59
14
1.0
ECMA-C21010
2.65
13.1
18
2.0
ECMA-C21020
4.45
22.0
21
0.4
ECMA-E21305
8.17
40.40
8
1.0
ECMA-E21310
8.41
41.59
18
1.5
ECMA-E21315
11.18
55.28
18
2.0
ECMA-E21320
ECMA-E21820
14.59
34.68
72.15
171.50
21
Servo Drive
(kW)
Low
Inertia
Medium
Inertia
Revision September 2013
2-9
ASDA-B2
Chapter 2 Installation and Storage
Servo Motor
Rotor Inertia
2
J (× 10-4kg.m )
Regenerative power
from empty load
3000r/min to stop
Eo (joule)
Max. regenerative
power of
capacitance
Ec(joule)
ECMA-E21830
54.95
271.73
28
ECMA-F21830
54.95
271.73
28
ECMA-G21303
8.17
40.40
8
0.75 ECMA-G21306
8.41
41.59
14
1.0
11.18
55.29
18
Servo Drive
(kW)
3.0
0.4
High
Inertia
ECMA-G21309
Eo = J x wr2/182 (joule), Wr : r/min
If the load inertia is N × motor inertia, the regenerative power will be (N+1) x E0 when
servo motor brakes from 3000r/min to 0. Then, the regenerative resistor can dissipate:
(N+1) x E0 - Ec (joule). If the time of repeat operation cycle is T sec, then the
regenerative power = 2 x ((N+1) x E0 - Ec) / T.
The calculating procedure is as follows:
Step
Procedure
Equation and Setting Method
1
Set the capacity of regenerative
resistor to the maximum
Change the value of P1-53 to maximum
2
Set the operation cycle T
Input by the users
3
Set motor speed wr
Input by the users or read via P0-02 Drive State
Display
4
Set load/motor inertia ratio N
Input by the users or read via P0-02 Drive State
Display
5
Calculate the max. regenerative
power Eo
Eo = J x wr2/182
6
Set the regenerative power Ec
that can be absorbed
Refer to the table above
7
Calculate the required
regenerative power capacity
2 x (N+1) x Eo-Ec)/ T
For example:
If we use 400W servo drive, the time of repeat operation cycle is T = 0.4 sec, max.
motor speed is 3000r/min, the load inertia = 7 × motor inertia, then the necessary the
power of regenerative resistor = 2 x ( (7+1) × 1.68 - 8) / 0.4 = 27.2W. If the calculation
result is smaller than regenerative power, we recommend the users to use the built-in
60W regenerative resistor. Usually the built-in regenerative resistor provided by ASDAB2 series can meet the requirement of general application when the external load
inertia is not excessive.
The users can see when the capacity of regenerative resistor is too small, the
accumulated power will be larger and the temperature will also increase. The fault,
ALE05 may occur if the temperature is over high. The following figure shows the actual
operation of regenerative resistor.
2-10
Revision September 2013
ASDA-B2
Chapter 2 Installation and Storage
(b) With Load
When there is an external load torque, servo motor is in reverse rotation when external
load greater than motor torque. Servo motor is usually in forward rotation and the motor
torque output direction is the same as the rotation direction. However, there is still
some special condition. If the motor output torque is in the reverse direction of rotation,
the servo motor is also in the reverse direction of rotation. The external power is input
into the servo drive through servo motor. The figure below is an example. The users
can see the motor is in forward rotation at constant speed when a sudden external load
torque change and great power is transmitted to regenerative resistor rapidly.
Motor Rotation Speed
External Load Torque
Motor Output Torque
Reverse
Rotation
Forward
Rotation
External load torque in reverse direction: TL x Wr
Reverse
Rotation
Forward
Rotation
TL : External load torque
For the safety, we strongly recommend the users should select the proper resistance
value according to the load.
For example:
When external load torque is a +70% rated torque and rotation speed reaches
3000r/min, if using 400W servo drive (rated torque: 1.27Nt-m), then the users need to
connect a external regenerative resistor which power is 2 x (0.7 x 1.27) x (3000 x 2 x π/
60) = 560W, 40.
Revision September 2013
2-11
ASDA-B2
Chapter 2 Installation and Storage
(2) Simple Calculation Method
The users can select the adequate regenerative resistors according to the allowable
frequency required by actual operation and the allowable frequency when the servo motor
runs without load. The allowable frequency when the servo motor run without load is the
maximum frequency that can be operated during continuous operation when servo motor
accelerate from 0r/min to rated speed and decelerate from rated speed down to 0r/min.
The allowable frequencies when the servo motor run without load are summarized in the
following table.
Allowable Frequencies for Servo Motor Running Without Load (times/min)
When Using Built-in Regenerative Resistor
Motor Capacity 600W
ECMA Series
06
750W
900W
1.0kW
1.5kW
2.0kW
2.0kW
3.0kW
07
09
10
15
20
20
30
83
(F100)
ECMAC
-
312
-
137
-
-
ECMAE
-
-
-
42
32
24
(F130)
10
(F180)
11
ECMAG
42
-
31
-
-
-
-
-
When the servo motor runs with load, the allowable frequency will change according to
the changes of the load inertia and rotation speed. Use the following equation to
calculate the allowable frequency.
Allowable fr equency =
Allowable frequency when serv o motor run without load
m+1
x
Rated s peed
Operating speed
2
times
mi n.
m = load/motor inertia ratio
The users can select the adequate regenerative resistors according to the allowable
frequency by referring to the table below:
Allowable Frequencies for Servo Motor Running Without Load (times/min)
When Using External Regenerative Resistor
ECMA□□C
Motor Capacity
100W
200W
400W
(F60)
400W
(F80)
750W
1.0kW
2.0kW
01
02
04
04
07
10
20
200W 80Ω
32793
6855
4380
1784
1074
458
273
400W 40Ω
-
-
-
-
-
916
545
1kW 30Ω
-
-
-
-
-
-
1363
Regenerative Resistor
2-12
Revision September 2013
ASDA-B2
Chapter 2 Installation and Storage
Allowable Frequencies for Servo Motor Running Without Load (times/min)
When Using External Regenerative Resistor
ECMA□□E
Motor Capacity
0.5kW
1kW
1.5kW
2.0kW
2.0kW
3.0kW
Regenerative Resistor
05
1.0
15
20
20
30
200W 80Ω
149
144
109
83
35
22
400W 40Ω
-
289
217
166
70
44
1kW 30Ω
-
-
-
416
175
110
Allowable Frequencies for Servo Motor Running Without Load (times/min)
When Using External Regenerative Resistor
ECMA□□G
Motor Capacity
0.3kW
0.6kW
0.9kW
03
06
09
200W 80Ω
149
144
109
400W 40Ω
-
-
217
Regenerative Resistor
When the regenerative resistor capacity is not enough, the users can connect to
multiple the same capacity regenerative resistors in parallel to increase it.
Dimensions
Delta Part Number : BR400W040 (400W 40Ω)
L1
L2
H
D
W
MAX. WEIGHT(g)
265
250
30
5.3
60
930
Revision September 2013
2-13
ASDA-B2
Chapter 2 Installation and Storage
Delta Part Number : BR1K0W020 (1kW 20Ω)
L1
400
L2
385
H
50
D
5.3
W
100
MAX. WEIGHT(g)
2800
NOTE
1) Regarding the selection of regenerative resistor, please refer to the table of regenerative
resistor specifications described in Appendix A.
2-14
Revision September 2013
Chapter 3 Connections and Wiring
This chapter provides information on wiring ASDA-B2 series products, the descriptions of
I/O signals and gives typical examples of wiring diagrams.
3.1 Connections
3.1.1 Connecting to Peripheral Devices
Revision September 2013
3-1
Chapter 3 Connections and Wiring
ASDA-B2
3.1.2 Servo Drive Connectors and Terminals
Terminal
Identification
Terminal
Description
Notes
L1c, L2c
Control circuit
terminal
Used to connect single-phase AC control circuit
power. (Control circuit uses the same voltage as the
main circuit.)
R, S, T
Main circuit
terminal
Used to connect single-phase or three-phase AC main
circuit power depending on connecting servo drive
model.
Used to connect servo motor
U, V, W
FG (
)
Servo motor
output
Terminal
Symbol
Wire Color
U
Red
V
White
W
Black
FG(
)
Internal resistor
Green
Description
Connecting to
three-phase
motor main
circuit cable.
Connecting to
ground terminal
( ) of the
servo drive.
Ensure the circuit is closed between
P and D, and the circuit is open
between P and C.
Connect regenerative resistor to P
External resistor and C, and ensure an open circuit
between P and D.
P , D, C,
Regenerative
resistor terminal
or braking unit
two places Ground terminal
Terminal
Identification
3-2
Terminal
Description
Connect braking unit to P and ,
and ensure an open circuit between
P and D, and P and C.
(N terminal is built in L1c, L2c, ,
External braking and R, S, T.)
unit
P : Connecting to (+) terminal of
V_BUS voltage.
: Connecting to (-) terminal of
V_BUS voltage.
Used to connect grounding wire of power supply and
servo motor.
Notes
CN1
I/O connector
Used to connect external controllers. Please refer to
section 3.3 for details.
CN2
Encoder
connector
Used to connect encoder of servo motor. Please refer
to section 3.4 for details.
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
Terminal
Identification
Terminal
Description
Notes
Terminal
Symbol
Wire Color
PIN No.
T+
Blue
4
T-
Blue/Black
5
Reserved
-
3
Reserved
-
2
Reserved
-
1
Reserved
-
9
+5V
Red / Red & White
8
GND
Black / Black &
White
6, 7
CN3
Communication
connector
Used to connect PC or keypad. Please refer to section
3.5 for details.
CN4
Reserved
connector
Reserved
CN5
Analog voltage
output terminal
Used to monitor the operation status. The drive
provides two channels, MON1 and MON2 to output
the analog voltage data. Output voltage is reference to
the power ground (GND).
NOTE
1) U, V ,W , CN1, CN2, CN3 terminals provide short circuit protection.
Revision September 2013
3-3
Chapter 3 Connections and Wiring
ASDA-B2
Wiring Notes
Please observe the following wiring notes while performing wiring and touching any
electrical connections on the servo drive or servo motor.
1. Ensure to check if the power supply and wiring of the "power" terminals (R, S, T,
L1c, L2c, U, V, & W) is correct.
2. Please use shielded twisted-pair cables for wiring to prevent voltage coupling
and eliminate electrical noise and interference.
3. As a residual hazardous voltage may remain inside the drive, please do not
immediately touch any of the "power" terminals (R, S, T, L1c, L2c, U, V, & W)
and/or the cables connected to them after the power has been turned off and the
charge LED is lit. (Please refer to the Safety Precautions on page ii).
4. The cables connected to R, S, T and U, V, W terminals should be placed in
separate conduits from the encoder or other signal cables. Separate them by at
least 30cm (11.8 inches).
5. If the encoder cable is too short, please use a twisted-shield signal wire with
grounding conductor. The wire length should be 20m (65.62ft.) or less. For
lengths greater than 20m (65.62ft.), the wire gauge should be doubled in order to
lessen any signal attenuation. Regarding the specifications of 20m (65.62ft.)
encoder cable, please choose wire gauge AWG26, UL2464 metal braided shield
twisted-pair cable.
6. As for motor cable selection, please use the 600V PTFE wire and the wire length
should be less than 98.4ft. (30m). If the wiring distance is longer than 30m
(98.4ft.), please choose the adequate wire size according to the voltage.
7. The shield of shielded twisted-pair cables should be connected to the SHIELD
end (terminal marked ) of the servo drive.
8. For the connectors and cables specifications, please refer to section 3.1.6 for
details.
3-4
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
3.1.3 Wiring Methods
For servo drives from 100W to 1.5kW the input power can be either single or threephase. However, single -phase connections are for servo drives 1.5kW and below only.
In the wiring diagram figures 3.2& 3.3:
Power ON : contact “a” (normally open)
Power OFF : contact “b” (normally closed)
MC: coil of electromagnetic contactor, self-holding power, contact of main circuit power
 Single-Phase Power Supply (1.5kW and below)
Revision September 2013
3-5
Chapter 3 Connections and Wiring
ASDA-B2
 Three-Phase Power Supply (all models)
3-6
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
3.1.4 Motor Power Cable Connector Specifications
The boxes () in the model names are for optional configurations. (Please refer to
section 1.2 for model explanation.)
Motor Model Name
U, V, W / Electromagnetic Brake Connector
Terminal
Identification
ECMA-C△0401S (100W)
ECMA-C△0602S (200W)
ECMA-C△0604S (400W)
ECMA-CM0604PS (400W)
ECMA-C△08047 (400W)
A
ECMA-C△0807S (750W)
ECMA-C△0907S (750W)
HOUSING: JOWLE (C4201H00-2*2PA)
ECMA-C△0910S (1000W)
ECMA-C△0602S (200W)
ECMA-C△0604S (400W)
ECMA-CM0604PS (400W)
ECMA-C△08047 (400W)
B
ECMA-C△0807S (750W)
ECMA-C△0907S (750W)
ECMA-C△0910S (1000W)
HOUSING: JOWLE (C4201H00-2*3PA)
ECMA-G△1303S (300W)
ECMA-E△1305S (500W)
ECMA-G△1306S (600W)
ECMA-GM1306PS (600W)
ECMA-G△1309S (900W)
ECMA-GM1309PS (900W)
ECMA-C△1010S (1000W)
C
ECMA-E△1310S (1000W)
ECMA-E△1315S (1500W)
ECMA-C△1020S (2000W)
ECMA-E△1320S (2000W)
3106A-20-18S
ECMA-E△1820S (2000W)
ECMA-E△1830S (3000W)
D
ECMA-F△1830S (3000W)
3106A-24-11S
Revision September 2013
3-7
Chapter 3 Connections and Wiring
ASDA-B2
Terminal
Identification
U
(Red)
V
(White)
W
(Black)
CASE GROUND
(Green)
BRAKE1
(Blue)
BRAKE2
(Brown)
A
1
2
3
4
-
-
B
1
2
4
5
3
6
C
F
I
B
E
G
H
D
D
E
F
G
A
B
When selecting the wire rod, please choose 600V PVC cable and the length should not longer
than 30m. If the length exceeds 30m, please take the received voltage into consideration when
selecting the wire size. Please refer to Section 3.1.6 for wire rod selection.
NOTE
1) The coil of brake has no polarity. The names of terminal identification are BRAKE1 (Blue) and
BRAKE2 (Brown).
2) The power supply for brake is DC24V. Never use it for VDD, the +24V source voltage.
3) Box, () in servo motor model represents brake or keyway / oil seal.
3-8
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
3.1.5 Encoder Connector Specifications
Encoder Cable Connection (Diagram 1)
Servo Drive
*2
CN2 Connector
Quick Connector
Connector of
Encoder Cable
(Drive Side)
*1
Connector of
Encoder Cable
(Motor Side)
Servo Motor
NOTE The scale of the objects does not match the dimensions as shown in the
drawing above. For different models of AC servo drives and motors, the
connection cables may differ.
1) Please refer to the descriptions of “Terminal Identification of Encoder
Connector” on page 3-10.
2) Please refer to section 3.4 for the descriptions of “Encoder Connector
CN2”.
The boxes () in the model names are for optional configurations (keyway, brake and
oil seal). (Please refer to section 1.2 for model explanation.)
Motor Model Name
Encoder Connector
ECMA-C20401S (100W)
ECMA-C20602S (200W)
ECMA-C20604S (400W)
ECMA-CM0604PS (400W)
ECMA-C208047 (400W)
ECMA-C20807S (750W)
ECMA-C20907S (750W)
ECMA-C20910S (1000W)
Revision September 2013
3-9
Chapter 3 Connections and Wiring
ASDA-B2
Terminal Identification of Encoder Connector
Connector of Encoder
Cable (Drive Side)
Connector of Encoder
Cable (Motor Side)
Housing : AMP(1-172161-9)
Servo Drive
(CN2)
Motor
Encoder
View from this side
Blue
T+
Blue/Black
T-
Black
Green
(Reserved) (Reserved)
Green/
Black
(Reserved) (Reserved)
Red/
Black/Black
Red&White &White
DC+5V
View from this side
GND
Shield
(Reserved) (Reserved)
White
T+
Red/Black White/Red
(Reserved) (Reserved)
Shield
Blue
GND
TBrown
DC+5V
The core color of the drive encoder connector
is for reference only. For the actual core color,
please refer to the actual purchased product.
If the users do not use the connector (without housing) and connect the cores from the
cable for wiring, please follow the terminal identification and core number of encoder
connector shown in the above table to complete the wiring. The users need to connect
core #1 to core #1, core #2 to core #2 and so on. To ease connection and to avoid
wiring error, it is recommended to number the cores first in accordance with the
terminal identification and then conducting the wiring.
3-10
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
Encoder Cable Connection (Diagram 2)
NOTE The scale of the objects does not match the dimensions as shown in the
drawing above. For different models of AC servo drives and motors, the
connection cables may differ.
1) Please refer to section 3.4 for the descriptions of “Encoder Connector
CN2”.
Revision September 2013
3-11
Chapter 3 Connections and Wiring
ASDA-B2
The boxes () in the model names are for optional configurations (keyway, brake and
oil seal). (Please refer to section 1.2 for model explanation.)
Motor Model Name
ECMA-G21303S (300W)
ECMA-E21305S (500W)
ECMA-G21306S (600W)
ECMA-GM1306PS (600W)
ECMA-G21309S (900W)
ECMA-GM1309PS (900W)
ECMA-C21010S (1000W)
ECMA-E21310S (1000W)
ECMA-E21315S (1500W)
ECMA-C21020S (2000W)
ECMA-E21320S (2000W)
ECMA-E21820S (2000W)
ECMA-E21830S (3000W)
ECMA-F21830S (3000W)
Encoder Connector
Pin
No.
A
Terminal
Identificati
on
Color
T+
Blue
B
T-
S
DC+5V
R
GND
L
BRAID
SHIELD
Blue&
Black
Red/Red
&White
Black/
Black&
White
–
Please select shielded multi-core and the shielded cable should connect to the SHIELD end.
Please refer to the description of Section 3.1.6.
NOTE
3-12
Box, () in servo motor model represents brake or keyway / oil seal.
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
3.1.6 Cable Specifications for Servo Drive
The recommended wire rods are shown as the following table:
2
Servo Drive and Servo Motor
ASD-B2-0121- ECMA-C20401S
ASD-B2-0221- ECMA-C20602S
ECMA-C20604S
ECMA-CM0604PS
ASD-B2-0421- ECMA-C208047
ECMA-E21305S
ECMA-G21303S
ECMA-C20807S
ECMA-C20907S
ASD-B2-0721-
ECMA-G21306S
ECMA-GM1306PS
ECMA-C21010S
ECMA-C20910S
ASD-B2-1021- ECMA-E21310S
ECMA-G21309S
ECMA-GM1309PS
ASD-B2-1521- ECMA-E21315S
ECMA-C21020S
ASD-B2-2023- ECMA-E21320S
ECMA-E21820S
ECMA-E21830S
ASD-B2-3023-
ECMA-F21830S
Revision September 2013
Power Cable - Wire Gauge AWG (mm )
L1c, L2c
R, S, T
U, V, W
P ,C
1.3
2.1
0.82
2.1
(AWG16)
(AWG14)
(AWG18)
(AWG14)
1.3
2.1
0.82
2.1
(AWG16)
(AWG14)
(AWG18)
(AWG14)
1.3
2.1
0.82
2.1
(AWG16)
(AWG14)
(AWG18)
(AWG14)
1.3
2.1
0.82
2.1
(AWG16)
(AWG14)
(AWG18)
(AWG14)
1.3
2.1
0.82
2.1
(AWG16)
(AWG14)
(AWG18)
(AWG14)
1.3
2.1
0.82
2.1
(AWG16)
(AWG14)
(AWG18)
(AWG14)
1.3
2.1
0.82
2.1
(AWG16)
(AWG14)
(AWG18)
(AWG14)
1.3
2.1
0.82
2.1
(AWG16)
(AWG14)
(AWG18)
(AWG14)
1.3
2.1
0.82
2.1
(AWG16)
(AWG14)
(AWG18)
(AWG14)
1.3
2.1
0.82
2.1
(AWG16)
(AWG14)
(AWG18)
(AWG14)
1.3
2.1
0.82
2.1
(AWG16)
(AWG14)
(AWG18)
(AWG14)
1.3
2.1
1.3
2.1
(AWG16)
(AWG14)
(AWG16)
(AWG14)
1.3
2.1
1.3
2.1
(AWG16)
(AWG14)
(AWG16)
(AWG14)
1.3
2.1
1.3
2.1
(AWG16)
(AWG14)
(AWG16)
(AWG14)
1.3
2.1
1.3
2.1
(AWG16)
(AWG14)
(AWG16)
(AWG14)
1.3
2.1
1.3
2.1
(AWG16)
(AWG14)
(AWG16)
(AWG14)
1.3
2.1
1.3
2.1
(AWG16)
(AWG14)
(AWG16)
(AWG14)
1.3
2.1
2.1
2.1
(AWG16)
(AWG14)
(AWG14)
(AWG14)
1.3
2.1
2.1
2.1
(AWG16)
(AWG14)
(AWG14)
(AWG14)
1.3
2.1
3.3
2.1
(AWG16)
(AWG14)
(AWG12)
(AWG14)
1.3
2.1
3.3
2.1
(AWG16)
(AWG14)
(AWG12)
(AWG14)
1.3
2.1
3.3
2.1
(AWG16)
(AWG14)
(AWG12)
(AWG14)
3-13
Chapter 3 Connections and Wiring
ASDA-B2
Encoder Cable
2
Encoder Cable - Wire Gauge AWG (mm )
Servo Drive
Wire Size
Core Number
UL Rating
Standard Wire
Length
ASD-B2-0121-
0.13 (AWG26)
10 core (4 pair)
UL2464
3m (9.84ft.)
ASD-B2-0221-
0.13 (AWG26)
10 core (4 pair)
UL2464
3m (9.84ft.)
ASD-B2-0421-
0.13 (AWG26)
10 core (4 pair)
UL2464
3m (9.84ft.)
ASD-B2-0721-
0.13 (AWG26)
10 core (4 pair)
UL2464
3m (9.84ft.)
ASD-B2-1021-
0.13 (AWG26)
10 core (4 pair)
UL2464
3m (9.84ft.)
ASD-B2-1521-
0.13 (AWG26)
10 core (4 pair)
UL2464
3m (9.84ft.)
ASD-B2-2023-
0.13 (AWG26)
10 core (4 pair)
UL2464
3m (9.84ft.)
ASD-B2-3023-
0.13 (AWG26)
10 core (4 pair)
UL2464
3m (9.84ft.)
NOTE
1)
Please use shielded twisted-pair cables for wiring to prevent voltage coupling and
eliminate electrical noise and interference.
2)
The shield of shielded twisted-pair cables should be connected to the SHIELD end
(terminal marked ) of the servo drive.
3)
In order to prevent fire hazard and accidents, please form the wiring by following the
cable specifications outlined above.
4)
The boxes () at the ends of the servo drive model names represent the model type of
ASDA-B2 series. For the actual model name, please refer to the ordering information of
the actual purchased product.
5)
The boxes () in the servo motor model names are for optional configurations (keyway,
brake and oil sea).
3-14
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
3.2 Basic Wiring
3.2.1 400W and below models
(with built-in regenerative resistor, but without cooling fan)
Connect to external
regenerative resistor
Power
1-phase/3-phase
200~230V
D C
P
S
T
IPM Module
Regeneration
Circuit
Phase Loss
Detection
R
Rectifier Circuit
PRB 60W
Servo Drive
U
Servo
Motor
V
M
W
Encoder
Control Power
L1C
L2C
±15V
+5V
+3.3V
GATE
DRIVE
+24V
Protection
Circuit
External Speed
Position
Control
A/D
Speed
Control
Current
Control
PWM
External Torque
Position Pulse
Current
Signal
Processing
CN1
Digital Input
Encoder Signal
A, B, Z Output
Encoder
Signal
Processing
Digital Output
CPLD
DSP
Serial
Communication
RS-232/RS-485
Battery
A/D
CN3
Data
Bus
CHARGE
CN2
Display
MODE
SHIFT
SET
CN4
D/A
Revision September 2013
CN5
Analog
Monitor
Output
3-15
Chapter 3 Connections and Wiring
ASDA-B2
3.2.2 750W model
(with built-in regenerative resistor, but without cooling fan)
3-16
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
3.2.3 1kW~1.5kW models
(with built-in regenerative resistor and cooling fan)
Revision September 2013
3-17
Chapter 3 Connections and Wiring
ASDA-B2
3.2.4 2kW~3kW models
(with built-in regenerative resistor and cooling fan)
3-18
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
3.3 Input / Output Interface Connector - CN1
3.3.1 I/O Signal (CN1) Connector Terminal Layout
In order to have a more flexible communication with the master, 6 programmable Digital
Outputs (DO) and 9 programmable Digital Inputs (DI) are provided. The setting of 9 digital
inputs and 6 digital outputs of each axis provided by ASDA-B2, which are parameter P210~P2-17, P2-36 and parameter P2-18~P2-22, P2-37 respectively. In addition, the
differential output encoder signal, A+, A-, B+, B-, Z+ and Z-, input of analog torque
command, analog speed/position command and pulse position command are also
provided. The followings are the pin diagrams.
Side View
Revision September 2013
Rear View
3-19
Chapter 3 Connections and Wiring
ASDA-B2
CN1 Terminal Signal Identification
16
1
DO4+
DO3-
DO3+
DO2DO2+
DO1DO1+
DI4DI1-
11
12
13
14
15
3-20
DI2-
Digital input
COM+
Power
input (12~24V)
DI9-
Digital input
OZ
Encoder Z pulse
Line-driver
output
COM-
DO6-
/OA
Encoder
/A pulse output
/OB
Encoder /B pulse
output
/OZ
Encoder /Z pulse
output
OB
Encoder B pulse
output
Digital input
25
10
Encoder
A pulse output
Digital input
24
9
OA
Digital output
23
8
V_REF
Analog speed
input (+)
Digital output
22
7
GND
Analog input
signal ground
Digital output
21
6
Analog torque
Input
Digital output
20
5
T_REF
Digital output
19
4
VDD
+24V power
output (for
external I/O)
Digital output
18
3
Digital output
Digital output
17
2
DO6+
VDD(24V) power
ground
26
27
28
29
DO4DO5-
31
DI7-
Digital input
32
DI6-
Digital input
33
DI5-
Digital input
34
DI3-
Digital input
35
PULL HI
Pulse applied
power
36
/HPULSE
High-speed
position pulse (-)
37
/SIGN
Position sign (-)
38
HPULSE
High-speed
position pulse (+)
39
SIGN
Position sign (+)
40
/HSIGN
High-speed
position sign (-)
41
/PULSE
Pulse input (-)
42
HSIGN
High-speed
position sign (+)
43
PULSE
Pulse input (+)
OCZ
Encoder Z pulse
Line-driver
output
Digital output
Digital output
DO5+
Digital output
GND
Analog input
signal ground
44
30
DI8-
Digital input
Digital output
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
3.3.2 Signals Explanation of Connector CN1
General Signals
Signal
Analog
Signal
Input
Position
Pulse
Output
Power
Details
Wiring Diagram
(Refer to 3.3.3)
V_REF
20
1. Motor speed command: -10V to +10V,
corresponds to -3000 ~ +3000 r/min speed
command (Factory default setting).
2. Motor speed command: -10V to +10V,
corresponds to -3 ~ +3 rotations position
command (Factory default setting).
T_REF
18
Motor torque command: -10V to +10V,
corresponds to -100% to +100% rated torque
command.
43
41
39
37
35
The drive can accept two different types of pulse
inputs: Line Driver (The max. input frequency is
500kHz) and Open Collector (The max. input
frequency is 200kHz).
Three different pulse commands can be selected
via parameter P1-00. Quadrature, CW + CCW
pulse & Pulse / Direction.
Should an Open Collector type of pulse be used
this terminal must be connected to an external
power supply to be lulled high.
C3/C4
HPULSE
/HPULSE
HSIGN
/HSIGN
38
36
42
40
The drive can accept two different types of highspeed pulse inputs: +5V input and Line-driver
input. The max. input frequency is 4MHz. Three
different pulse commands can be selected via
parameter P1-00. They are A phase + B phase
(Quadrature), CW pulse + CCW pulse, and Pulse
+ Direction.
C4-2
OA
/OA
21
22
OB
/OB
25
23
Encoder signal output A, B, Z (Line-driver
output). The motor encoder signals are available
through these terminals.
C13/C14
OZ
/OZ
13
24
OCZ
44
Encoder signal output Z (Open-collector output).
-
VDD
17
VDD is the +24V source voltage provided by the
drive. Maximum permissible current 500mA.
COM+
COM-
11
14
COM+ is the common voltage rail of the Digital
Input and Digital Output signals. Connect VDD to
COM+ for source mode.
For external applied power sink mode (+12V to
+24V), the positive terminal should be connected
to COM+ and the negative to COM-.
GND
19
The polarity of VDD is with respect to Ground
(GND).
PULSE
/PULSE
Position
Pulse
SIGN
Input
/SIGN
PULL HI
Highspeed
Position
Pulse
Input
Pin No
Revision September 2013
C1
C1
-
3-21
Chapter 3 Connections and Wiring
ASDA-B2
There are numerous operation mode of this servo drive (please refer to Chapter 6.1).
Each operation mode needs different I/O signal. In order to use the terminal in a more
efficient way, the selection of I/O signal has to be programmable. That is to say, users
can choose the desired DI/DO signal to meet the demand. Basically, the default setting
of DI/DO signal has already have the appropriate function which can satisfy the demand
of normal application.
3-22
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
Users have to select the operation mode based on the needs first (please refer to
Chapter 6.1 for the introduction of each mode) and refer to the following DI/DO table to
know the corresponding default setting of DI/DO signal and Pin No of the selected mode
in order to conduct the wiring.
The table below lists the default setting of DI/DO signal function and pin No:
The explanation of DO signal default setting is as the followings.
DO
Signal
Assigned
Control Mode
SRDY
SON
ZSPD
TSPD
Details
+
-
ALL
7
6
SRDY is activated when the servo drive is
ready to run. All fault and alarm conditions,
if present, have been cleared.
Not assigned
-
-
Servo ready (SRDY) is "ON" where the
servo is ready to run, NO fault / alarm
exists.
4
ZSPD is activated when the drive senses
the motor is equal to or below the Zero
Speed Range setting as defined in
parameter P1-38.
ALL
ALL
(except PT)
TPOS PT, PT-S, PT-T
TQL
Pin No.
(Default)
Not assigned
5
-
1
-
TSPD is activated once the drive has
detected the motor has reached the Target
Rotation Speed setting as defined in
parameter P1-39.
1. When the drive is in PT mode, TPOS
will be activated when the position
26
error is equal and below the setting
value of P1-54.
TQL is activated when the drive has
- detected that the motor has reached the
torques limits.
C5/C6/C7/C8
ALRM is activated when the drive has
detected a fault condition. (However, when
Reverse limit error, Forward limit error,
27
Emergency stop, Serial communication
error, and Undervoltage these fault occur,
WARN is activated first.)
ALRM
ALL
28
BRKR
ALL
-
-
BRKR is the control terminal of motor
brake.
OLW
ALL
-
-
OLW is activated when the servo drive has
detected that the motor has reached the
output overload level .
Revision September 2013
Wiring Diagram
(Refer to 3.3.3)
3-23
Chapter 3 Connections and Wiring
ASDA-B2
WARN
ALL
-
-
Servo warning output. WARN is activated
when the drive has detected Reverse limit
error, Forward limit error, Emergency stop,
Serial communication error, and
Undervoltage these fault conditions.
S_CMP
S, Sz
-
-
SP_CMP will be activated when the speed
error is equal and below the setting value
of P1-47.
NOTE
1) PINS 3 & 2 can TSPD when control mode S is selected.
2) The DO signals that do not have pin numbers in Tables 3.B are not default DO signals. If
the users want to use these non-default DO signals, the users need to change the settings
of parameters P2-18 ~ P2-22. The “state” of the output function may be turned ON or OFF
as it will be dependant on the settings of parameters P2-18 ~ P2-22. Please refer to section
3.3.3 for details.
DI Signals
DI
Signal
Details
SON
ALL
9
Servo On. Switch servo to "Servo Ready".
ARST
ALL
33
A number of Faults (Alarms) can be cleared
by activating ARST.
GAINUP
ALL
-
CCLR
3-24
Assigned Pin No.
Control
(Default)
Mode
PT
10
Gain switching
When CCLR is activated the setting is
parameter P2-50 Pulse Clear Mode is
executed.
ZCLAMP
ALL
-
When this signal is On and the motor speed
value is lower than the setting value of P1-38,
it is used to lock the motor in the instant
position while ZCLAMP is On.
CMDINV
T, S
-
When this signal is On, the motor is in
reverse rotation.
TRQLM
S, Sz
10
ON indicates the torque limit command is
valid.
ON indicates the speed limit command is
valid.
SPDLM
T, Tz
10
STOP
-
-
SPD0
S, Sz,
34
Wiring Diagram
(Refer to 3.3.3)
C9/C10
C11/C12
C9/C10
C11/C12
Motor stop.
Select the source of speed command:
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
PT-S, S-T
SPD1
TCM0
8
PT, T, Tz,
PT-T
34
SPD1
SPD0
Parameter
OFF
OFF
OFF
ON
P1-09
ON
OFF
P1-10
ON
ON
P1-11
S mode: analog input
Sz mode: 0
Select the source of torque command:
TCM1
OFF
TCM0
OFF
Parameter
T mode: analog
input
Tz mode: 0
TCM1
S-T
8
OFF
ON
P1-12
ON
OFF
P1-13
ON
ON
P1-14
S-P
PT-S
31
Speed / Position mode switching
OFF: Speed, ON: Position
S-T
S-T
31
Speed / Torque mode switching
OFF: Speed, ON: Torque
T-P
PT-T
31
Torque / Position mode switching
OFF: Torque, ON: Position
EMGS
ALL
30
It should be contact “b” and normally ON or a
fault (ALRM) will display.
NL(CWL)
PT, S, T
Sz, Tz
32
Reverse inhibit limit. It should be contact “b”
and normally ON or a fault (ALRM) will
display.
PL(CCWL)
PT, S, T
Sz, Tz
31
Forward inhibit limit. It should be contact “b”
and normally ON or a fault (ALRM) will
display.
TLLM
Not
assigned
-
Reverse operation torque limit (Torque limit
function is valid only when P1-02 is enabled)
TRLM
Not
assigned
-
Forward operation torque limit (Torque limit
function is valid only when P1-02 is enabled)
JOGU
ALL
-
Forward JOG input. When JOGU is activated,
the motor will JOG in forward direction.
JOGD
ALL
-
Reverse JOG input. When JOGD is activated,
the motor will JOG in reverse direction.
GNUM0
PT, PT-S
-
Electronic gear ratio (Numerator) selection 0
[See P2-60~P2-62]
GNUM1
PT, PT-S
-
Electronic gear ratio (Numerator) selection 1
[See P2-60~P2-62]
Revision September 2013
3-25
Chapter 3 Connections and Wiring
INHP
PT, PT-S
-
ASDA-B2
Pulses inhibit input. When the drive is in
position mode, if INHP is activated, the
external pulse input command is not valid.
C9/C10
C11/C12
NOTE
1) The DI signals that do not have pin numbers in Tables 3.C are not default DI signals. If the
users want to use these non-default DI signals, the users need to change the settings of
parameters P2-10 ~ P2-17. The “state” of the output function may be turned ON or OFF as
it will be dependant on the settings of parameters P2-10 ~ P2-17. Please refer to section
3.3.3 for details.
The default DI and DO signals in different control mode are listed in the following table
3.F and table 3.G. Although the content of the table 3.F and table 3.G do not provide
more information than the table 3.B and table 3.C above, as each control mode is
separated and listed in different row, it is easy for user to view and can avoid confusion.
However, the Pin number of each signal can not be displayed in the table 3.F and
table 3.G.
Table 3.1 Default DI signals and Control modes
Signal
Function
PT
S
T
Sz
Tz
SON
0x01 Servo On
DI1
DI1
DI1
DI1
DI1
ARST
0x02 Reset
DI5
DI5
DI5
DI5
DI5
GAINUP
CCLR
3-26
DI
Code
0x03
PT-S PT-T
DI1
DI1
DI2
DI2
S-T
DI1
Gain switching in speed
and position mode
0x04 Pulse clear
ZCLAMP
0x05 Low speed CLAMP
CMDINV
0x06
Reserved
0x07 Reserved
Reserved
0x08 Reserved
DI2
Command input
reverse control
TRQLM
0x09 Torque limit enabled
SPDLM
0x10 Speed limit enabled
DI2
DI2
DI2
DI2
STOP
0x46 Motor stop
SPD0
0x14
Speed command
selection 0
DI3
DI3
DI3
DI3
SPD1
0x15
Speed command
selection 1
DI4
DI4
DI4
DI4
TCM0
0x16
Torque command
selection 0
DI3
DI3
DI3
DI3
DI5
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
Signal
DI
Code
TCM1
0x17
Function
Torque command
selection 1
S-P
Position / Speed mode
0x18 switching (OFF: Speed,
ON: Position)
S-T
Speed / Torque mode
0x19 switching (OFF: Speed,
ON: Torque)
T-P
Torque / Position mode
0x20 switching (OFF:
Torque, ON: Position)
PT
S
DI4
T
Sz
DI4
Tz
PT-S PT-T
DI4
DI4
S-T
DI6
DI7
DI7
DI7
Reserved 0x2C Reserved
Reserved 0x2D Reserved
EMGS
0x21 Emergency stop
DI8
DI8
DI8
DI8
DI8
0x22 Reverse inhibit limit
DI6
DI6
DI6
DI6
DI6
PL(CCWL) 0x23 Forward inhibit limit
DI7
DI7
DI7
DI7
DI7
NL(CWL)
Reserved
DI8
DI8
0x24 Reserved
TLLM
0x25
Reverse operation
torque limit
TRLM
0x26
Forward operation
torque limit
Reserved
0x27 Reserved
Reserved
0x36 Reserved
JOGU
0x37 Forward JOG input
JOGD
0x38 Reverse JOG input
GNUM0
0x43
Electronic gear ratio
(Numerator) selection 0
GNUM1
0x44
Electronic gear ratio
(Numerator) selection 1
INHP
DI8
0x45 Pulse inhibit input
NOTE
1) For Pin numbers of DI1~DI8 signals, please refer to section 3.3.1.
Table 3.2 Default DO signals and Control modes
Signal
DO
Code
SRDY
0x01 Servo ready
SON
Function
PT
S
T
Sz
Tz
DO1
DO1
DO1
DO1
DO1
PT-S PT-T
S-T
DO1
DO1
DO1
0x02 Servo On
Revision September 2013
3-27
Chapter 3 Connections and Wiring
ASDA-B2
Signal
DO
Code
ZSPD
0x03 Zero speed
TSPD
0x04 Speed reached
TPOS
0x05 Positioning completed DO4
Function
TQL
0x06
Reached torques
limits
ALRM
0x07
Servo alarm output
(Servo fault)
BRKR
0x08 Electromagnetic brake
OLW
0x10
PT
S
T
Sz
Tz
DO2
DO2
DO2
DO2
DO3
DO3
DO3
DO5
PT-S PT-T
S-T
DO2
DO2
DO2
DO2
DO3
DO3
DO3
DO3
DO4
DO4
DO5
DO5
DO5
DO5
DO5
DO5
DO4
DO4
DO4
DO4
DO5
Output overload
warning
WARN
0x11 Servo warning output
SNL(SCWL)
0x13 Reverse software limit
SPL(SCCWL) 0x14 Forward software limit
SP_OK
0x19 Speed reached output
NOTE
1) For Pin numbers of DO1~DO6 signals, please refer to section 3.3.1.
3-28
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
3.3.3 Wiring Diagrams of I/O Signals (CN1)
The valid voltage range of analog input command in speed and torque mode is -10V
~+10V. The command value can be set via relevant parameters.
C1: Speed / Torque analog signal input
Servo Drive
10kΩ
10kΩ
20 V-REF
(18 T-REF )
+
_ 10V
Approx.
10kΩ
19 GND
SG
C2: Analog monitor output (MON1, MON2)
Revision September 2013
3-29
Chapter 3 Connections and Wiring
ASDA-B2
There are two kinds of pulse inputs, Line driver input and Open-collector input. Max.
input pulse frequency of Line driver input is 500kpps and max. input pulse frequency of
Open-collector input is 200kpps.
C3-1: The source of pulse input is open-collector NPN equipment which applies the
internal power of the servo drive.
C3-2: The source of pulse input is open-collector PNP equipment which applies the
internal power of the servo drive.
3-30
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
C3-3: The source of pulse input is open-collector NPN equipment which applies the
external power of the servo drive.
Controller
Servo Drive
PULL_HI 35
+
-
Approx.
2KΩ
DC24V
2KΩ
/SIGN 37
2KΩ
/PULSE 41
75Ω
Max. input pulse
frequency is 200Kpps
75Ω
Approx.
2KΩ
75Ω
Max. input pulse
frequency is 200Kpps
75Ω
SG
C3-4: The source of pulse input is open-collector PNP equipment which applies the
external power of the servo drive.

Caution: Do not apply to dual power or it may damage the servo drive.
Revision September 2013
3-31
Chapter 3 Connections and Wiring
ASDA-B2
C4-1: Pulse input (Line driver) It requires 5V power supply only. Never apply a 24V power supply.
C4-2: High-speed pulse input (Line driver). It requires 5V power supply only. Never apply a 24V
power supply.

3-32
Caution: The high-speed pulse input interface is not an isolated input interface.
To prevent noise and interference, ensure that the ground terminal of the
controller and the servo drive should be connected to each other.
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
Be sure to connect a diode when the drive is applied to inductive load.
(Permissible current: 40mA, Instantaneous peak current: max. 100mA)
C5: Wiring of DO signal, for the use of internal
power supply, general load
C6: Wiring of DO signal, for the use of internal
power supply, inductive load
C7: Wiring of DO signal, for the use of external
power supply, general load
C8: Wiring of DO signal, for the use of external
power supply, inductive load
Revision September 2013
3-33
Chapter 3 Connections and Wiring
ASDA-B2
Use a relay or open-collector transistor to input signal.
NPN transistor with multiple emitter fingers (SINK Mode)
C9: Wiring of DI signal, for the use of internal
power supply
C10: Wiring of DI signal, for the use of external
power supply
PNP transistor with multiple emitter fingers (SOURCE Mode)
C11: Wiring of DI signal, for the use of internal
power supply

3-34
C12: Wiring of DI signal, for the use of external
power supply
Caution: Do not apply to dual power or it may damage the servo drive.
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
C13: Encoder output signal (Line driver)
C14: Encoder output signal (Photocoupler)
C15: Encoder OCZ output (Open-collector Z-pulse output)
24V
Servo Drive
Max. Spec: 30V
100mA
OCZ 44
GND 29
Revision September 2013
3-35
Chapter 3 Connections and Wiring
ASDA-B2
3.3.4 User-defined DI and DO signals
If the default DI and DO signals could not be able to fulfill users’ requirements, there
are still user-defined DI and DO signals. The setting method is easy and they are all
defined via parameters. The user-defined DI and DO signals are defined via
parameters P2-10 to P2-17 P2-36 and P2-18 to P2-22 and P-37. Please refer to the
following Table 3.H for the settings.
Table 3.H User-defined DI and DO signals
Signal Name
Pin No.
Parameter
DI1-
CN1-9
DI2-
DI
3-36
Signal Name
Pin No.
P2-10
DO1+
CN1-7
CN1-10
P2-11
DO1-
CN1-6
DI3-
CN1-34
P2-12
DO2+
CN1-5
DI4-
CN1-8
P2-13
DO2-
CN1-4
DI5-
CN1-33
P2-14
DO3+
CN1-3
DI6-
CN1-32
P2-15
DO3-
CN1-2
DI7-
CN1-31
P2-16
DO4+
CN1-1
DI8-
CN1-30
P2-17
DO4-
CN1-26
DI9
CN1-12
P2-36
DO5+
CN1-28
DO5-
CN1-27
DO6+
CN1-16
DO6-
CN1-15
DO
Parameter
P2-18
P2-19
P2-20
P2-21
P2-22
P2-37
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
3.4 Encoder Connector CN2
(1) The layout of CN2 Drive Connector
Side View
Rear View
(2) The layout of CN2 Motor Connector
B A M
L
C
N
P
T
D
K
R
S
J
E
F G H
Quick Connector
3106A-20-29S
Military Connector
Revision September 2013
3-37
Chapter 3 Connections and Wiring
ASDA-B2
CN2 Terminal Signal Identification
Drive Connector
Motor Connector
PIN No.
Terminal
Identification
Description
Military
Connector
Quick
Connector
Color
4
T+
Serial communication signal
input / output (+)
A
1
Blue
5
T-
Serial communication signal
input / output (-)
B
4
Blue & Black
-
-
Reserved
-
-
-
-
-
Reserved
-
-
-
8
+5V
+5V power supply
S
7
Red / Red &
White
7, 6
GND
Ground
R
8
Black / Black
& White
Shell
Shielding
Shielding
L
9
-
Using the encoder cable with shielding (double shielding is the best) is able to prevent
voltage coupling and eliminate the noise and interference from other electrical sources. Be
sure to observe the following steps to complete the shielding surrounding the encoder
cable.
(1) Solder the centre cores on the
metal part of the connector
adequately for good ground
contact with the plate and
shielding.
3-38
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
(2) Trim the ends of the cores and
install the cores with shielding
into the plastic case of the
connector as shown in the
figure.
(3) Tighten the screws to complete
the shielding.
Revision September 2013
3-39
Chapter 3 Connections and Wiring
ASDA-B2
3.5 Serial Communication Connector CN3
CN3 Terminal Layout and Identification
The servo drive can be connected to a PC or controller via a serial communication
connector. Users can operate the servo drive through PC software supplied by Delta
(contact to the dealer). The communication connector/port of Delta servo drive can
provide three common serial communication interfaces: RS-232 and RS-485
connection. RS-232 is mostly be used but is somewhat limited. The maximum cable
length for an RS-232 connection is 15 meters (50 feet). Using RS-485 interface can
allow longer distance for transmission and support multiple drives to be connected
simultaneously.
CN3 Port (Female)
Side View
Rear View
Please read carefully the following note. Improper wiring may
cause damage or injury!
CN3 Terminal Signal Identification
PIN No.
Signal Name
1
Grounding
2
RS-232 data
transmission
3
-
Terminal
Identification
GND
RS-232_TX
RS-232_RX
Description
Ground
For data transmission of the servo drive.
Connected to the RS-232 interface of PC.
Reserved
For data receiving of the servo drive.
Connected to the RS-232 interface of PC.
4
RS-232 data receiving
5
RS-485 data
transmission
RS-485(+)
For data transmission of the servo drive
(differential line driver + end)
6
RS-485 data
transmission
RS-485(-)
For data transmission of the servo drive
(differential line driver - end)
NOTE
For the connection of RS-485, please refer to section 8.1 in Chapter 8.
2) There are two kinds of IEEE1394 communication cables available on the market. If the user
uses one kind of cable, which its GND terminal (Pin 1) and its shielding is short-circuited,
the communication may be damaged. Never connect the case of the terminal to the ground
of this kind of communication cable.
1)
3-40
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
3.6 Analog Monitor Output Connector - CN5
Analog Monitor Output Connector CN5 is used to monitor the motor operation status.
Motor characteristics such as speed and current can be represented by analog voltages.
The drive provides two channels (MON1 and MON2) which can be configured with the
parameter P0-03 to output the desired characteristics.
Please refer to the parameter P0-03 for monitoring commands and P1-04 / P1-05 for
scaling factors. Output voltage is reference to the power ground (GND).
CN5 Terminal Layout and Identification
3
2
1
CN5
Signal Cable for CN5 Connector
PIN No.
Signal Name
Description
Color
1
MON1
Monitor analog data 1
Red
2
GND
Ground
White
3
MON2
Monitor analog data 2
Black
Revision September 2013
Wiring Diagram
(Refer to 3.3.3)
C2
3-41
Chapter 3 Connections and Wiring
ASDA-B2
3.7 Standard Connection Example
3.7.1 Position (PT) Control Mode
MCCB
Servo Drive
ASDA-B2 series
MC
R
S
T
AC 200/230 V
Three-phase
50/60Hz
P⊕
D
C
U
V
W
L1c
L2c
Pulse input
(Line Driver)*1
±10V
10KΩ
High-speed
pulse input *2
(Line Receiver)
SON
CCLR
TCM0
TCM1
ARST
CWL
CCWL
EMGS
0
SRDY
1.5KΩ
ZSPD
1.5KΩ
HOME
1.5KΩ
TPOS
1.5KΩ
ALRM
1.5KΩ
0
1.5KΩ
24V
A phase
differential signal
Encoder
pulse
input
B phase
differential signal
Z phase
differential signal
Z phase signal
(open-collector)
CN1
37
/SIGN
SIGN
39
/PULSE
41
PULSE
43
T-REF
18
GND
19
/HSIGN
40
HSIGN
42
/HPULSE 36
HPULSE 38
VDD
17
COM+
11
COM14
DI1
9
DI2
10
DI3
34
DI4
8
DI5
33
DI6
32
DI7
31
DI8
30
DI9
12
DO1+
7
DO16
DO2+
5
DO24
DO3+
3
DO32
DO4+
1
DO426
DO5+
28
DO527
DO6+
16
DO615
OA
21
/OA
22
OB
25
/OB
23
OZ
13
/OZ
24
OCZ
GND
10KΩ
Reserved
Reserved
10KΩ
DC 24V
*3
5 KΩ
5 KΩ
5 KΩ
5 KΩ
5 KΩ
5 KΩ
5 KΩ
8
6,7
CN3
6
5
4
3
2
1
CN5
1
2
3
Regenerative
resistor
Red
White
Power supply
Black
Green
24V
EMGS BRKR
*5
Brake
Encoder
T+
T+5V
GND
Blue
Blue&
Black
Red/Red&
White
Twisted-pair of
twisted-shield
cable
SG
Black/Black
&White
RS485RS485+
RS232_RX
RS232_TX
GND
MON1
GND
MON2
10KΩ
10KΩ
Twisted-pair of
twisted-shield
cable
SG
5 KΩ
5 KΩ
44
19
Max. output current 3A
Voltage 50V
3-42
CN2
4
5
*4
Please note:
*1 Please refer to C3 ~ C4 wiring
diagrams in section 3.3.3.
*2 Please refer to C3 ~ C4 wiring
diagrams in section 3.3.3.
*3 Please refer to C9 ~ C12 wiring
diagrams (SINK / SOURCE mode) in
section 3.3.3.
*4 Model that under 200W has no builtin regenerative resistor.
*5 The brake coil has no polarity.
Revision September 2013
ASDA-B2
Chapter 3 Connections and Wiring
3.7.2 Speed Control Mode
MCCB
Servo Drive
ASDA-B2 series
MC
R
S
T
AC 200/230 V
Three-phase
50/60Hz
P⊕
L1c
L2c
±10V
10KΩ
±10V
10KΩ
V_REF
/SIGN
GND
SIGN
T_REF
GND
CN1
20
19
18
19
10KΩ
10KΩ
10KΩ
10KΩ
SRDY
1.5KΩ
ZSPD
1.5KΩ
TSPD
1.5KΩ
BRKR
1.5KΩ
ALRM
1.5KΩ
0
1.5KΩ
24V
A phase
differential signal
B phase
differential signal
Encoder
pulse
output
Z phase
differential signal
Z phase signal
(open-collector)
Reserved
VDD
COM+
COMDI1
DI2
DI3
DI4
DI5
DI6
DI7
DI8
DI9
DO1+
DO1DO2+
DO2DO3+
DO3DO4+
DO4DO5+
DO5DO6+
DO6OA
/OA
OB
/OB
OZ
/OZ
17
11
14
9
10
34
8
33
32
31
30
12
7
6
5
4
3
2
1
26
28
27
16
15
21
22
25
23
13
24
OCZ
GND
44
19
*1
5 KΩ
5 KΩ
5 KΩ
5 KΩ
5 KΩ
5 KΩ
5 KΩ
8
6,7
CN3
6
5
4
3
2
1
CN5
1
2
3
Regenerative
resistor
Red
Power supply
White
Black
Green
24V
EMGS BRKR
*3
Brake
Encoder
T+
T+5V
GND
Blue
Blue&
Black
Red/Red&
White
Twisted-pair or
twisted-shield
cable
SG
Black/Black
&White
RS485RS485+
RS232_RX
RS232_TX
GND
MON1
GND
MON2
10KΩ
10KΩ
Twisted-pair or
twisted-shield
cable
SG
5 KΩ
5 KΩ
Max. output current 3A
Voltage 50V
Revision September 2013
CN2
4
5
Reserved
DC 24V
SON
TRQLM
SPD0
SPD1
ARST
CWL
CCWL
EMGS
0
D
C
U
V
W
*2
Please note:
*1 Please refer to C9 ~ C12 wiring
diagrams (SINK / SOURCE mode)
in section 3.3.3.
*2 The servo drive provides built-in
regenerative resistor.
*3 The brake coil has no polarity.
3-43
Chapter 3 Connections and Wiring
ASDA-B2
3.7.3 Torque Control Mode
MCCB
Servo Drive
ASDA-B2 series
MC
R
S
T
AC 200/230 V
Three-phase
50/60Hz
P⊕
L1c
L2c
±10V
10KΩ
±10V
10KΩ
V_REF
/SIGN
GND
SIGN
T_REF
GND
CN1
20
19
18
19
10KΩ
10KΩ
10KΩ
SON
SPDLM
TCM0
TCM1
ARST
CWL
CCWL
EMGS
0
SRDY
1.5KΩ
ZSPD
1.5KΩ
TSPD
1.5KΩ
BRKR
1.5KΩ
ALRM
1.5KΩ
0
1.5KΩ
24V
A phase
differential signal
B phase
differential signal
Encoder
pulse
output
Z phase
differential signal
Z phase signal
(open-collector)
17
11
14
9
10
34
8
33
32
31
30
12
7
6
5
4
3
2
1
26
28
27
16
15
21
22
25
23
13
24
OCZ
GND
44
19
Reserved
*1
5 KΩ
5 KΩ
5 KΩ
5 KΩ
5 KΩ
5 KΩ
5 KΩ
8
6,7
CN3
6
5
4
3
2
1
CN5
1
2
3
Regenerative
resistor
Red
Power supply
White
Black
Green
24V
EMGS BRKR
*3
Brake
Encoder
T+
T+5V
GND
Blue
Blue&
Black
Blue&Black
Red/Red&
White
Twisted pair or
twisted-shield
cable
SG
Black/Black
&White
RS485RS485+
RS232_RX
RS232_TX
GND
MON1
GND
MON2
10KΩ
10KΩ
Twisted pair or
twisted-shield
cable
SG
5 KΩ
5 KΩ
Max. output current 3A
Voltage 50V
3-44
CN2
4
5
Reserved
10KΩ
DC 24V
VDD
COM+
COMDI1
DI2
DI3
DI4
DI5
DI6
DI7
DI8
DI9
DO1+
DO1DO2+
DO2DO3+
DO3DO4+
DO4DO5+
DO5DO6+
DO6OA
/OA
OB
/OB
OZ
/OZ
D
C
U
V
W
*2
Please note:
*1 Please refer to C9 ~ C12 wiring
diagrams (SINK / SOURCE mode)
in section 3.3.3.
*2 The servo drive provides built-in
regenerative resistor.
*3 The brake coil has no polarity.
Revision September 2013
Chapter 4 Display and Operation
This chapter describes the basic operation of the digital keypad and the features it offers.
4.1 Description of the Digital Keypad
The digital keypad includes the display panel and function keys. The Figure 4.1 shows all
of the features of the digital keypad and an overview of their functions.
Figure 4.1
Name
Function
LCD Display
The LCD Display (5-digit, 7-step display panel) shows the monitor codes,
parameter settings and operation values of the AC servo drive.
Charge LED
The Charge LED lights to indicate the power is applied to the circuit.
MODE Key
MODE Key. Pressing MODE key can enter or exit different parameter groups,
and switch between Monitor mode and Parameter mode.
SHIFT Key
SHIFT Key. Pressing SHIFT key can scrolls through parameter groups. After a
parameter is selected and its value displayed, pressing SHIFT key can move
the cursor to the left and then change parameter settings (blinking digits) by
using arrow keys.
UP and DOWN
Key
UP and DOWN arrow Key. Pressing the UP and DOWN arrow key can scroll
through and change monitor codes, parameter groups and various parameter
settings.
SET Key
SET Key. Pressing the SET key can display and save the parameter groups,
the various parameter settings. In monitor mode, pressing SET key can switch
decimal or hexadecimal display. In parameter mode, pressing SET key can
enter into parameter setting mode. During diagnosis operation, pressing SET
key can execute the function in the last step. (The parameter settings changes
are not effective until the SET key is pressed.)
Revision September 2013
4-1
Chapter 4 Display and Operation
ASDA-B2
4.2 Display Flowchart
Figure 4.2
Keypad Operation
1. When the power is applied to the AC servo drive, the LCD display will show the
monitor function codes for approximately one second, then enter into the monitor
mode.
2. In monitor mode, pressing MODE key can enter into parameter mode. In parameter
mode, pressing MODE key can return to monitor mode.
3. No matter working in which mode, when an alarm occurs, the system will enter into
fault mode immediately. In fault mode, pressing MODE key can switch to other
modes. In other modes, if no key is pressed for over 20 seconds, the system will
return to fault mode automatically.
4. In monitor mode, pressing UP or DOWN arrow key can switch monitor parameter
code. At this time, monitor display symbol will display for approximately one second.
5. In monitor mode, pressing MODE key can enter into parameter mode, pressing the
SHIFT key can switch parameter group and pressing UP or DOWN arrow key can
change parameter group code.
6. In parameter mode, the system will enter into the setting mode immediately after the
Set key is pressed. The LCD display will display the corresponding setting value of
this parameter simultaneously. Then, users can use UP or DOWN arrow key to
change parameter value or press MODE key to exit and return back to the
parameter mode.
7. In parameter setting mode, the users can move the cursor to left by pressing the
SHIFT key and change the parameter settings (blinking digits) by pressing the UP or
DOWN arrow key.
8. After the setting value change is completed, press SET key to save parameter
settings or execute command.
4-2
Revision September 2013
ASDA-B2
Chapter 4 Display and Operation
9. When the parameter setting is completed, LCD display will show the end code
“SAVED“ and automatically return back to parameter mode.
Revision September 2013
4-3
Chapter 4 Display and Operation
ASDA-B2
4.3 Status Display
4.3.1 Save Setting Display
After the SET key is pressed, LCD display will show the following display messages for
approx. one second according to different status.
Display Message
Description
The setting value is saved correctly. [Saved)
This parameter is read only. Write-protected. (Read-Only)
Invalid password or no password was input. (Locked)
The setting value is error or invalid. (Out of Range)
The servo system is running and it is unable to accept this
setting value to be changed. (Servo On)
This parameter is valid after restarting the drive. (Power On)
4.3.2 Decimal Point Display
Display Message
Description
High/Low byte display. When the data is a decimal 32-bit
data, these two digits are used to show if the display is high
byte or low byte.
Negative value display. When the data is displayed in decimal
format, the most left two digits represent negative sign no
matter it is a 16-bit or 32-bit data. If the data is displayed in
hexadecimal format, it is a positive value always and no
negative sign is displayed.
4.3.3 Fault Message Display
Display Message
Description
When the AC servo drive has a fault, LCD display will
display “ALnnn”. “AL” indicates the alarm and “nnn”
indicates the drive fault code. For the list of drive fault code,
please refer to parameter P0-01 or refer to Chapter 11
(Troubleshooting).
4.3.4 Polarity Setting Display
Display Message
Description
Positive value display. When entering into parameter setting
mode, pressing UP or DOWN arrow key can increase or
decrease the display value. SHIFT key is used to change
the selected digit (The selected digit will blink).
4-4
Revision September 2013
ASDA-B2
Chapter 4 Display and Operation
Display Message
Description
Negative value display. Continuously press SHIFT key for
two seconds and then the positive(+) or negative(-) sign can
be switched. When the setting value exceeds its setting
range, the positive(+) and negative(-) sign can not be
switched. (The negative value display is for a decimal
negative value only. There is no negative value display for a
hexadecimal negative value.)
4.3.5 Monitor Setting Display
When the AC servo drive is applied to power, the LCD display will show the monitor
function codes for approximately one second and then enter into the monitor mode. In
monitor mode, in order to change the monitor status, the users can press UP or
DOWN arrow key or change parameter P0-02 directly to specify the monitor status.
When the power is applied, the LCD display will show ASDA-B2 first and then display
the monitor status depending on the setting value of P0-02. For example, if the setting
value of P0-02 is 4 when the power is applied, the monitor function will be input pulse
number of pulse command. After ASDA-B2 shows on the LCD display, the C-PLS
monitor codes will display next and then the pulse number will display after.
P0-02
Setting
Display Message
Description
Unit
0
Motor feedback pulse number (after
electronic gear ratio is set)
[user unit]
1
Input pulse number of pulse
command (after electronic gear ratio
is set)
[user unit]
2
Position error counts between control
command pulse and feedback pulse
[user unit]
3
Motor feedback pulse number
(encoder unit, 1600000 pulse/rev)
[pulse]
4
Input pulse number of pulse
command (before electronic gear
ratio is set) (encoder unit)
[pulse]
5
Position error counts (after electronic
gear ratio is set) (encoder unit)
[pulse]
6
Input frequency of pulse command
[Kpps]
7
Motor rotation speed
[r/min]
8
Speed input command
[Volt]
9
Speed input command
[r/min]
10
Torque input command
[Volt]
Revision September 2013
4-5
Chapter 4 Display and Operation
P0-02
Setting
ASDA-B2
Display Message
Description
Unit
11
Torque input command
[%]
12
Average load
[%]
13
Peak load
[%]
14
Main circuit voltage
15
Ratio of load inertia to Motor inertia
(Please note that if the display is 130,
it indicates that the actual inertia is
13.0)
16
IGBT temperature
[ C]
17
Resonance frequency (The low byte
is the first resonance point and the
high byte is the second resonance
point.)
[Hz]
18
Absolute pulse number relative to
encoder (use Z phase as home). The
value of Z phase home point is 0, and
it can be the value from -5000 to
+5000 pulses.
[Volt]
[0.1times]
o
-
The following table lists the display examples of monitor value:
Display Message
(Dec.)
Description
16-bit
Data
(Hex.)
(Dec. High Byte)
(Dec. Low Byte)
(Hex. High Byte)
(Hex. Low Byte)
32-bit
Data
Decimal display. When the actual value is 1234,
the display is 01234.
Hexadecimal display. When the actual value is
0x1234, the display is 1234.
Decimal display. When the actual value is
1234567890, the display of high byte is 1234.5
and the display of low byte is 67890.
Hexadecimal display. When the actual value is
0x12345678, the display of high byte is h1234
and the display of low byte is L5678.
Negative value display. When the actual value is -12345,
the display is 1.2.345. (The negative value display is
displayed to indicate a decimal negative value. There is
no negative value display for a hexadecimal negative
value.)
4-6
Revision September 2013
ASDA-B2
Chapter 4 Display and Operation
NOTE
1) Dec. represents Decimal display and Hex. represents Hexadecimal display.
2) The above display methods are both available in monitor mode and parameter setting mode.
3) All monitor variables are 32-bit data. The users can switch to high byte or low byte and display
format (Dec. or Hex.) freely. Regarding the parameters listed in Chapter 8, for each
parameter, only one kind of display format is available and cannot be changed.
Revision September 2013
4-7
Chapter 4 Display and Operation
ASDA-B2
4.4 General Function Operation
4.4.1 Fault Code Display Operation
After entering the parameter mode P4-00 to P4-04 (Fault Record), press SET key to
display the corresponding fault code history for the parameter.
Figure 4.3
4-8
Revision September 2013
ASDA-B2
Chapter 4 Display and Operation
4.4.2 JOG Operation
After entering parameter mode P4-05, the users can follow the following steps to
perform JOG operation. (Please also refer to Figure 4.4).
Step1. Press the SET key to display the JOG speed. (The default value is 20 r/min).
Step2. Press the UP or DOWN arrow keys to increase or decrease the desired JOG
speed. (This also can be undertaken by using the SHIFT key to move the
cursor to the desired unit column (the effected number will blink) then changed
using the UP and DOWN arrow keys. The example display in Figure 4.4 is
adjusted as 100 r/min.)
Step3. Press the SET key when the desired JOG speed is set. The Servo Drive will
display "JOG".
Step4. Press the UP or DOWN arrow keys to jog the motor either CCW or CW. The
motor will only rotate while the arrow key is activated.
Step5. To change JOG speed again, press the MODE key. The servo Drive will
display "P4 - 05". Press the SET key and the JOG speed will displayed again.
Refer back to #2 and #3 to change speed.
NOTE
1) JOG operation is effective only when Servo On (when the servo drive is enabled).
Revision September 2013
4-9
Chapter 4 Display and Operation
ASDA-B2
Figure 4.4
4.4.3 Force Output Control Operation
For testing, the digital outputs can be forced to be activated (ON) or inactivated (OFF)
by using parameter P2-08 and P4-06. First, set P2-08 to 406 to enable the force output
control function and then using P4-06 to force the digital outputs to be activated.
Follow the setting method in Figure 4.5 to enter into Force Output Control operation
mode. When P4-06 is set to 2, the digital output, DO2 is activated. When P4-06 is set
to 7, the digital outputs, DO1, DO2 and DO3 are both activated. The parameter setting
value of P4-06 is not retained when power is off. After re-power the servo drive, all
digital outputs will return to the normal status. If P2-08 is set to 400, it also can switch
the Force Output Control operation mode to normal Digital Output (DO) Control
operation mode.
The DO function and status is determined by P2-18 to P2-22. This function is enabled
only when Servo Off (the servo drive is disabled).
4-10
Revision September 2013
ASDA-B2
Chapter 4 Display and Operation
Figure 4.5
NOTE
1) As the display of P4-06 is hexadecimal, 0(zero) of the fifth digit will not show on the LED
display.
Revision September 2013
4-11
Chapter 4 Display and Operation
ASDA-B2
4.4.4 DI Diagnosis Operation
Following the setting method in Figure 4.6 can perform DI diagnosis operation
(parameter P4-07, Input Status). According to the ON and OFF status of the digital
inputs DI1 to DI9, the corresponding status will display on the servo drive LED display.
When the Bit is set to “1”, it means that the corresponding digital input signal is ON.
(Please also refer to Figure 4.6)
For example:
Suppose that the servo drive LED display is “1E1”.
“E” is hexadecimal, which is equal to “1110” in binary system, and it means that the
digital inputs DI6 ~ DI8 are ON.
Figure 4.6
(Hexadecimal Display)
4-12
Revision September 2013
ASDA-B2
Chapter 4 Display and Operation
4.4.5 DO Diagnosis Operation
Following the setting method in Figure 4.7 can perform DO diagnosis operation
(parameter P4-09, Output Status Display). According to the ON and OFF status of the
digital outputs DO1 to DO6, the corresponding status will display on the servo drive
LED display. When the Bit is set to “1”, it means that the corresponding digital output
signal is ON. (Please also refer to Figure 4.7)
For example:
Suppose that the servo drive LED display is “3F”.
“F” is hexadecimal, which is equal to “1111” in binary system, and it means that the
digital outputs DO1 ~ DO4 are ON.
Figure 4.7
(Hexadecimal Display)
Revision September 2013
4-13
Chapter 4 Display and Operation
ASDA-B2
This page is intentionally left blank.
4-14
Revision September 2013
Chapter 5 Trial Run and Tuning
Procedure
This chapter, which is divided into two parts, describes trial run for servo drive and motor.
One part is to introduce the trial run without load, and the other part is to introduce trial run
with load. Ensure to complete the trial run without load first before performing the trial run
with load.
5.1 Inspection without Load
In order to prevent accidents and avoid damaging the servo drive and mechanical system,
the trial run should be performed under no load condition (no load connected, including
disconnecting all couplings and belts). Do not run servo motor while it is connected to load
or mechanical system because the unassembled parts on motor shaft may easily
disassemble during running and it may damage mechanical system or even result in
personnel injury. After removing the load or mechanical system from the servo motor, if the
servo motor can runs normally following up the normal operation procedure (when trial run
without load is completed), then the users can connect to the load and mechanical system
to run the servo motor.
In order to prevent accidents, the initial trial run for servo motor should be
conducted under no load conditions (separate the motor from its couplings
and belts).
 Caution: Please perform trial run without load first and then perform trial run
with load connected. After the servo motor is running normally and regularly
without load, then run servo motor with load connected. Ensure to perform trial
run in this order to prevent unnecessary danger.

After power in connected to AC servo drive, the charge LED will light and it indicates that
AC servo drive is ready. Please check the followings before trial run:
Inspection before operation (Control power is not applied)

Inspect the servo drive and servo motor to insure they were not damaged.

To avoid an electric shock, be sure to connect the ground terminal of servo drive to
the ground terminal of control panel.
Revision September 2013
5-1
Chapter 5 Trial Run and Tuning Procedure
ASDA-B2

Before making any connection, wait 10 minutes for capacitors to discharge after the
power is disconnected, alternatively, use an appropriate discharge device to
discharge.

Ensure that all wiring terminals are correctly insulated.

Ensure that all wiring is correct or damage and or malfunction may result.

Visually check to ensure that there are not any unused screws, metal strips, or any
conductive or inflammable materials inside the drive.

Never put inflammable objects on servo drive or close to the external regenerative
resistor.

Make sure control switch is OFF.

If the electromagnetic brake is being used, ensure that it is correctly wired.

If required, use an appropriate electrical filter to eliminate noise to the servo drive.

Ensure that the external applied voltage to the drive is correct and matched to the
controller.
Inspection during operation (Control power is applied)

Ensure that the cables are not damaged, stressed excessively or loaded heavily.
When the motor is running, pay close attention on the connection of the cables and
notice that if they are damaged, frayed or over extended.

Check for abnormal vibrations and sounds during operation. If the servo motor is
vibrating or there are unusual noises while the motor is running, please contact the
dealer or manufacturer for assistance.

Ensure that all user-defined parameters are set correctly. Since the characteristics
of various machinery equipment are different, in order to avoid accident or cause
damage, do not adjust the parameter abnormally and ensure the parameter setting
is not an excessive value.

Ensure to reset some parameters when the servo drive is off (Please refer to
Chapter 7). Otherwise, it may result in malfunction.

If there is no contact sound or there be any unusual noises when the relay of the
servo drive is operating, please contact your distributor for assistance or contact
with Delta.

Check for abnormal conditions of the power indicators and LED display. If there is
any abnormal condition of the power indicators and LED display, please contact
your distributor for assistance or contact with Delta.
5-2
Revision September 2013
ASDA-B2
Chapter 5 Trial Run and Tuning Procedure
5.2 Applying Power to the Drive
The users please observe the following steps when applying power supply to the servo
drive.
1. Please check and confirm the wiring connection between the drive and motor is correct.
1) Terminal U, V, W and FG (frame ground) must connect to Red, White, Black and
Green cables separately (U: Red, V: White, W: Black, FG: Green). If not connect
to the specified cable and terminal, then the drive cannot control motor. The motor
grounding lead, FG must connect to grounding terminal. For more information of
cables, please refer to section 3.1.
2) Ensure to connect encoder cable to CN2 connector correctly. If the users only
desire to execute JOG operation, it is not necessary to make any connection to
CN1 and CN3 connector. For more information of the connection of CN2
connector, please refer to Section 3.1 and 3.4.

Do not connect the AC input power (R, S, T) to the (U, V, W) output terminals.
This will damage the AC servo drive.
2. Main circuit wiring
Connect power to the AC servo. For three-phase input power connection and singlephase input power connection, please refer to Section 3.1.3.
3. Turn the Power On
The Power includes control circuit power (L1c, L2c) and main circuit power (R, S, T).
When the power is on, the normal display should be shown as the following figure:
As the default settings of digital input signal, DI6, DI7 and DI8 are Reverse Inhibit Limit
(NL), Forward Inhibit Limit (PL) and Emergency Stop (EMGS) respectively, if the users
do not want to use the default settings of DI6~DI8, the users can change their settings
by using parameters P2-15 to P2-17 freely. When the setting value of parameters P215 to P2-17 is 0, it indicates the function of this DI signal is disabled. For more
information of parameters P2-15 to P2-17, please refer to Chapter 7 “Parameters”.
If the parameter P0-02 is set as motor speed (06), the normal display should be shown
as the following figure:
If there is no text or character displayed on the LED display, please check if the voltage
of the control circuit terminal (L1c and L2c) is over low.
Revision September 2013
5-3
Chapter 5 Trial Run and Tuning Procedure
ASDA-B2
1) When display shows:
Over voltage:
The main circuit voltage has exceeded its maximum allowable value or input power is
error (Incorrect power input).
Corrective Actions:

Use voltmeter to check whether the input voltage falls within the rated input
voltage.

Use voltmeter to check whether the input voltage is within the specified limit.
2) When display shows:
Encoder error:
Check if the wiring is correct. Check if the encoder wiring (CN2) of servo motor is
loose or incorrect.
Corrective Actions:

Check if the users perform wiring recommended in the user manual.

Examine the encoder connector and cable.

Inspect whether wire is loose or not.

Check if the encoder is damaged.
3) When display shows:
Emergency stop activated:
Please check if any of digital inputs DI1~DI9 signal is set to “Emergency Stop”
(EMGS).
Corrective Actions:

5-4
If it does not need to use “Emergency Stop (EMGS)” as input signal, the users
only need to confirm that if all of the digital inputs DI1~DI8 are not set to
Revision September 2013
ASDA-B2
Chapter 5 Trial Run and Tuning Procedure
“Emergency Stop (EMGS)”. (The setting value of parameter P2-10 to P2-17
and P2-36 is not set to 21.)

If it is necessary to use “Emergency Stop (EMGS)” as input signal, the users
only need to confirm that which of digital inputs DI1~DI9 is set to “Emergency
Stop (EMGS)” and check if the digital input signal is ON (It should be activated).
4) When display shows:
Reverse limit switch error:
Please check if any of digital inputs DI1~DI9 signal is set to “Reverse inhibit limit
(NL)” and check if the signal is ON or not.
Corrective Actions:

If it does not need to use “Reverse inhibit limit (NL)” as input signal, the users
only need to confirm that if all of the digital inputs DI1~DI9 are not set to
“Reverse inhibit limit (NL)”. (The setting value of parameter P2-10 to P2-17 and
P2-36 is not set to 22.)

If it is necessary to use “Reverse inhibit limit (NL)” as input signal, the users
only need to confirm that which of digital inputs DI1~DI9 is set to “Reverse
inhibit limit (NL)” and check if the digital input signal is ON (It should be
activated).
5) When display shows:
Forward limit switch error:
Please check if any of digital inputs DI1~DI9 signal is set to “Forward inhibit limit
(PL)” and check if the signal is ON or not.
Corrective Actions:

If it is no need to use “Forward inhibit limit (PL)” as input signal, the users only
need to confirm that if all of the digital inputs DI1~DI9 are not set to “Forward
inhibit limit (PL)”. (The setting value of parameter P2-10 to P2-17 and P2-36 is
not set to 23.)
Revision September 2013
5-5
Chapter 5 Trial Run and Tuning Procedure

ASDA-B2
If it is necessary to use “Forward inhibit limit (PL)” as input signal, the users
only need to confirm that which of digital inputs DI1~DI9 is set to “Forward
inhibit limit (PL)” and check if the digital input signal is ON (It should be
activated).
When “Digital Input 1 (DI1)” is set to Servo On (SON), if DI1 is set to ON (it indicates
that Servo On (SON) function is enabled) and the following fault message shows on
the display:
6) When display shows:
Overcurrent:
Corrective Actions:

Check the wiring connections between the servo drive and motor.

Check if the circuit of the wiring is closed.

Remove the short-circuited condition and avoid metal conductor being exposed.
7) When display shows:
Undervoltage:
Corrective Actions:

Check whether the wiring of main circuit input voltage is normal.

Use voltmeter to check whether input voltage of main circuit is normal.

Use voltmeter to check whether the input voltage is within the specified
specification.
NOTE
1) If there are any unknown fault codes and abnormal display when applying power to the
drive or servo on is activated (without giving any command), please inform the
distributor or contact with Delta for assistance.
5-6
Revision September 2013
ASDA-B2
Chapter 5 Trial Run and Tuning Procedure
5.3 JOG Trial Run without Load
It is very convenient to use JOG trial run without load to test the servo drive and motor as it
can save the wiring. The external wiring is not necessary and the users only need to
connect the digital keypad to the servo drive. For safety, it is recommended to set JOG
speed at low speed. Please refer to the following steps to perform JOG trial run without
load.
STEP 1: Turn the drive ON through software. Ensure that the setting value of parameter
P2-30 should be set to 1 (Servo On).
STEP 2: Set parameter P4-05 as JOG speed (unit: r/min). After the desired JOG speed is
set, and then press SET key, the drive will enter into JOG operation mode
automatically
STEP 3: The users can press UP and DOWN key to change JOG speed and press
SHIFT key to adjust the digit number of the displayed value.
STEP 4: Pressing SET key can determine the speed of JOG operation.
STEP 5: Pressing UP key and the servo motor will run in CCW direction. After releasing
UP key, the motor will stop running.
STEP 6: Pressing DOWN key and the servo motor will run in CW direction. After
releasing DOWN key, the motor will stop running.
N (CW) and P(CCW) Definition:
CCW (Counterclockwise): when facing the servo motor shaft, CCW is reverse
running.
CW (Clockwise): when facing the servo motor shaft, CW is forward running.
STEP 7: When pressing MODE key, it can exit JOG operation mode.
Revision September 2013
5-7
Chapter 5 Trial Run and Tuning Procedure
ASDA-B2
In the example below, the JOG speed is adjusted from 20r/min (Default setting) to
100r/min.
5-8
Revision September 2013
ASDA-B2
Chapter 5 Trial Run and Tuning Procedure
5.4 Speed Trial Run without Load
Before speed trial run, fix and secure the motor as possible to avoid the danger
from the reacting force when motor speed changes.
STEP 1:
Set the value of parameter P1-01 to 02 and it is speed (S) control mode. After selecting
the operation mode as speed (S) control mode, please restart the drive as P1-01 is
effective only after the servo drive is restarted (after switching power off and on).
STEP 2:
In speed control mode, the necessary Digital Inputs are listed as follows:
Digital Input
Parameter Setting
Value
Sign
Function Description
CN1 PIN No.
DI1
P2-10=101
SON
Servo On
DI1-=9
DI2
P2-11=109
TRQLM
Torque limit enabled
DI2-=10
DI3
P2-12=114
SPD0
Speed command selection
DI3-=34
DI4
P2-13=115
SPD1
Speed command selection
DI4-=8
DI5
P2-14=102
ARST
Reset
DI5-=33
DI6
P2-15=0
Disabled
This DI function is disabled
-
DI7
P2-16=0
Disabled
This DI function is disabled
-
DI8
P2-17=0
Disabled
This DI function is disabled
-
DI9
P2-36=0
Disabled
This DI function is disabled
-
By default, DI6 is the function of reverse inhibit limit, DI7 is the function of forward inhibit
limit and DI6 is the function of emergency stop (DI8), if the users do not set the setting
value of parameters P2-15 to P2-17 and P2-36 to 0 (Disabled), the faults (ALE13, 14 and
15) will occur (For the information of fault messages, please refer to Chapter 10).
Therefore, if the users do not need to use these three digit inputs, please set the setting
value of parameters P2-15 to P2-17 and P2-36 to 0 (Disabled) in advance.
All the digital inputs of Delta ASDA-B2 series are user-defined, and the users can set the
DI signals freely. Ensure to refer to the definitions of DI signals before defining them (For
the description of DI signals, please refer to Table 7.A in Chapter 7). If any alarm code
displays after the setting is completed, the users can restart the drive or set DI5 to be
activated to clear the fault. Please refer to section 5.2.
Revision September 2013
5-9
Chapter 5 Trial Run and Tuning Procedure
ASDA-B2
The speed command is selected by SPD0, SPD1. Please refer to the following table:
Speed
Command No.
DI signal of CN1
SPD1
SPD0
S1
0
0
S2
0
1
S3
1
0
S4
1
1
Command Source
Content
Range
External analog
command
Voltage between VREF and GND
-10V ~ +10V
P1-09
-50000 ~ 50000
P1-10
-50000 ~ 50000
P1-11
-50000 ~ 50000
Internal parameter
0: indicates OFF (Normally Open); 1: indicates ON (Normally Closed)
The range of internal parameter is from -50000 to 50000.
Setting value of speed command = Setting range x unit (0.1 r/min).
For example:
If P1-09 is set to +30000, the setting value of speed command = +30000 x 0.1 r/min =
+3000 r/min.
The settings of speed command:
P1-09 is set to 30000
Input value command
Rotation direction
P1-10 is set to 1000
+
CW
P1-11 is set to -30000
-
CCW
STEP 3:
1. The users can use DI1 to enable the servo drive (Servo ON).
2. If DI3 (SPD0) and DI4 (SPD1) are OFF both, it indicates S1 command is selected. At
this time, the motor is operating according to external analog command.
3. If only DI3 is ON (SPD0), it indicates S2 command (P1-09 is set to 3000) is selected,
and the motor speed is 3000r/min at this time.
4. If only DI4 is ON (SPD1), it indicates S3 command (P1-10 is set to 100) is selected,
and the motor speed is 100r/min at this time.
5. If DI3 (SPD0) and DI4 (SPD1) are ON both, it indicates S4 command (P1-11 is set to
-3000) is selected, and the motor speed is -3000r/min at this time.
6. Repeat the action of (3), (4), (5) freely.
7. When the users want to stop the speed trial run, use DI1 to disable the servo drive
(Servo OFF).
5-10
Revision September 2013
ASDA-B2
Chapter 5 Trial Run and Tuning Procedure
5.5 Tuning Procedure
Estimate the ratio of Load Inertia to Servo Motor Inertia (J_load /J_motor): JOG Mode
Tuning Procedure
1.
After wiring is completed, when power in connected to the AC servo
drive, the right side display will show on the LCD display.
2.
Press MODE key to enter into parameter mode.
3.
Press SHIFT key twice to select parameter group.
4.
Press UP key to view each parameter and select parameter P2-17.
5.
Press SET key to display the parameter value as shown on the right
side.
6.
Press SHIFT key twice to change the parameter values. Use UP key to
cycle through the available settings and then press SET key to determine
the parameter settings.
7.
Press UP key to view each parameter and select parameter P2-30.
8.
Press SET key to display the parameter value as shown on the right
side.
9.
Select parameter value 1. Use UP key to cycle through the available
settings.
Display
10. At this time, the servo drive is ON and the right side display will appear
next.
11. Press DOWN key three times to select the ratio of Load Inertia to Servo
Motor Inertia (J_load /J_motor).
12. Display the current ratio of Load Inertia to Servo Motor Inertia (J_load
/J_motor). (5.0 is default setting.)
13. Press MODE key to select parameter mode.
14. Press SHIFT key twice to select parameter group.
15. Press UP key to select user parameter P4-05.
16. Press SET key and JOG speed 20r/min will be displayed. Press UP and
DOWN key to increase and decrease JOG speed. To press SHIFT key
one time can add one digit number.
17. Select desired JOG speed, press SET key and it will show the right side
display.
18. Pressing UP key is forward rotation and pressing DOWN key is reverse rotation.
19. Execute JOG operation in low speed first. After the machine is running smoothly, then
execute JOG operation in high speed.
Revision September 2013
5-11
Chapter 5 Trial Run and Tuning Procedure
Tuning Procedure
ASDA-B2
Display
20. The ratio of Load Inertia to Servo Motor Inertia (J_load /J_motor) cannot be shown in the
display of JOG parameter P4-05 operation. Please press MODE key twice continuously and
the users can see the ratio of Load Inertia to Servo Motor Inertia (J_load /J_motor). Then,
execute JOG operation again, press MODE key once and press SET key twice to view the
display on the keypad. Check if the value of J_load /J_motor is adjusted to a fixed value and
displayed on the keypad after acceleration and deceleration repeatedly.
5.5.1 Tuning Flowchart
5-12
Revision September 2013
ASDA-B2
Chapter 5 Trial Run and Tuning Procedure
5.5.2 Load Inertia Estimation Flowchart
Revision September 2013
5-13
Chapter 5 Trial Run and Tuning Procedure
ASDA-B2
5.5.3 Auto Mode Tuning Flowchart
Set P2-32 to 1 (1: Auto Mode [Continuous adjustment] )
The servo drive will continuously estimate the system inertia, save the measured load
inertia value automatically and memorized in P1-37 every 30 minutes by referring to
the frequency response settings of P2-31.
P2-31 : Auto Mode Stiffness Setting (Default setting: 80)
In Auto mode and Semi-Auto mode, the speed loop frequency response settings are
as follows:
1 ~ 50Hz : Low stiffness and low frequency response
51 ~ 250Hz : Medium stiffness and medium frequency response
251 ~ 550Hz : High stiffness and high frequency response
Adjust P2-31: Increase the setting value of P2-31 to enhance the stiffness or reduce
the noise. Continuously perform the adjustment until the satisfactory performance is
achieved.
5-14
Revision September 2013
ASDA-B2
Chapter 5 Trial Run and Tuning Procedure
5.5.4 Semi-Auto Mode Tuning Flowchart
Set P2-32 to 2 (2: Semi-Auto Mode [Non-continuous adjustment] )
The servo drive will continuously perform the adjustment for a period of time. After the
system inertia becomes stable, it will stop estimating the system inertia, save the
measured load inertia value automatically, and memorized in P1-37. When switching
from other modes, such as Manual Mode or Auto Mode, to Semi-Auto Mode, the servo
drive will perform continuous adjustment for estimating the load inertia (P1-37) again.
The servo drive will refer to the frequency response settings of P2-31 when estimating
the system inertia.
P2-31 : Auto Mode Stiffness Setting (Default setting: 80)
In Auto mode and Semi-Auto mode, the speed loop frequency response settings are
as follows:
1 ~ 50Hz : Low stiffness and low frequency response
51 ~ 250Hz : Medium stiffness and medium frequency response
251 ~ 550Hz : High stiffness and high frequency response
Adjust P2-31: Increase the setting value of P2-31 to enhance the frequency response
or reduce the noise. Continuously perform the adjustment until the satisfactory
performance is achieved.
Revision September 2013
5-15
Chapter 5 Trial Run and Tuning Procedure
ASDA-B2
NOTE
1) When bit0 of P2-33 is set to 1, it indicates that the system inertia estimation of semi-auto mode
has been completed and the measured load inertia value is saved and memorized in P1-37
automatically.
2) If reset bit0 of P2-33 to 0, it will start estimating the system inertia again.
5-16
Revision September 2013
ASDA-B2
Chapter 5 Trial Run and Tuning Procedure
5.5.5 Limit of Load Inertia Estimation
The accel. / decel. time for reaching 2000r/min must be below 1 second.
The rotation speed must be above 200r/min.
The load inertia must be 100 multiple or less of motor inertia.
The change of external force and the inertia ratio can not be too much.
In Auto Mode (P2-32 is set to 1), the measured load inertia value will be saved
automatically and memorized in P1-37 every 30 minutes. In Semi-Auto Mode, it will
stop estimating the load inertia after a period of continuous adjustment time when the
system inertia becomes stable. The measured load inertia value will be saved
automatically and memorized in P1-37 when load inertia estimation is stopped.
Revision September 2013
5-17
Chapter 5 Trial Run and Tuning Procedure
ASDA-B2
NOTE
1) Parameters P2-44 and P2-46 are used to set notch filter attenuation rate. If the resonance can
not be suppressed when the setting values of P2-44 and P2-46 are set to 32bB (the maximum
value), please decrease the speed loop frequency response. After setting P2-47, the users can
check the setting values of P2-44 and P2-46. If the setting value of P2-44 is not 0, it indicates
that one resonance frequency exists in the system and then the users can read P2-43, i.e. the
frequency (unit is Hz) of the resonance point. When there is any resonance point in the system,
its information will be shown in P2-45 and P2-46 as P2-43 and P2-44.
2) If the resonance conditions are not improved when P2-47 is set to 1 for over three times,
please adjust notch filters (resonance suppression parameters) manually to or eliminate the
resonance.
5-18
Revision September 2013
ASDA-B2
Chapter 5 Trial Run and Tuning Procedure
5.5.6 Mechanical Resonance Suppression Method
In order to suppress the high frequency resonance of the mechanical system, ASDAB2 series servo drive provides three notch filters (resonance suppression parameters)
for resonance suppression. Two notch filters can be set to suppress the resonance
automatically. If the users do not want to suppress the resonance automatically, these
two notch filter can also be set to or eliminate the resonance manually.
Please refer to the following flowchart for manual adjustment.
Revision September 2013
5-19
Chapter 5 Trial Run and Tuning Procedure
ASDA-B2
5.5.7 Relationship between Tuning Modes and Parameters
Tuning Mode
Manual Mode
Auto Mode
[Continuous
Adjustment]
Semi-Auto Mode
[Non-continuous
Adjustment]
P2-32
0(Default
setting)
AutoSet
Parameter
User-defined Parameter
Gain Value
None
P1-37 (Ratio of Load Inertia to Servo
Motor Inertia [J_load / J_motor])
P2-00 (Proportional Position Loop Gain)
P2-04 (Proportional Speed Loop Gain)
P2-06 (Speed Integral Compensation)
P2-25 (Low-pass Filter Time Constant
of Resonance Suppression)
P2-26 (External Anti-Interference Gain)
Fixed
1
P1-37
P2-00
P2-02
P2-04
P2-06
P2-25
P2-26
P2-49
2
P1-37
P2-00
P2-02
P2-04
P2-06
P2-25
P2-26
P2-49
P2-31 (Auto Stiffness and Frequency
response Level)
Continuous
Adjusting
(every 30
minutes)
P2-31 (Auto Stiffness and Frequency
response Level)
Noncontinuous
Adjusting
(stop after a
period of
time)
When switching mode #1 to #0, the setting value of P2-00, P2-02, P2-04, P2-06, P225, P2-26 and P2-49 will change to the value that measured in #1 auto-tuning mode.
When switching mode #2 to #0, the setting value of P2-00, P2-02, P2-04, P2-06, P225, P2-26 and P2-49 will change to the value that measured in #2 semi-auto tuning
mode.
5-20
Revision September 2013
ASDA-B2
Chapter 5 Trial Run and Tuning Procedure
5.5.8 Gain Adjustment in Manual Mode
The position and speed responsiveness selection is depending on and determined by
the the control stiffness of machinery and conditions of applications. Generally, high
reponsiveness is essential for the high frequency positioning control of mechanical
facilities and the applications of high precision process system. However, the higher
responsiveness may easily result in the resonance of machinery system. Therefore, for
the applications of high responsiveness, the machinery system with control stiffness is
needed to avoid the resonance. Especially when adjusting the responsiveness of
unfamiliar machinery system, the users can gradually increase the gain setting value
to improve responsiveness untill the resonance occurs, and then decrease the gain
setting value. The relevant parameters and gain adjusting methods are described as
follows:

KPP, Parameter P2-00 Proportional Position Loop Gain
This parameter is used to determine the responsiveness of position loop (position
loop gain). It could be used to increase stiffness, expedite position loop response
and reduce position error. When the setting value of KPP is higher, the response
to the position command is quicker, the position error is less and the settling time
is also shorter. However, if the setting value is over high, the machinery system
may generate vibration or noise, or even overshoot during positioning. The
position loop responsiveness is calculated as follows:

KVP, Parameter P2-04 Proportional Speed Loop Gain
This parameter is used to determine the frequency response of speed loop
(speed loop gain). It could be used to expedite speed loop response. When the
setting value of KVP is higher, the response to the speed command is quicker.
However, if the setting value is over high, it may result in the resonance of
machinery system. The frequency response of speed loop must be higher than
the 4~6 times of the frequency response of position loop. If frequency response of
position loop is higher than the frequency response of speed loop, the machinery
system may generate vibration or noise, or even overshoot during positioning.
The speed loop frequency response is calculated as follows:
JM: Motor Inertia
JL: Load Inertia
P1-37: 0.1 times
When the value of P1-37 (no matter it is the measured load inertia value or the
set load inertia value) is equal to the actual load inertia value, the actual speed
loop frequency response will be:
Revision September 2013
5-21
Chapter 5 Trial Run and Tuning Procedure
=

ASDA-B2
K VP
Hz
2
.
KVI, Parameter P2-06 Speed Integral Compensation
If the setting value of KVI is higher, the capability of decreasing the speed control
deviation is better. However, if the setting value is over high, it may easily result
in the vibration of machinery system. The recommended setting value is as
follows:

NLP, Parameter P2-25 Low-pass Filter Time Constant of Resonance
Suppression
When the value of (J_load / J_motor) is high, the responsiveness of speed loop
may decrease. At this time, the users can increase the setting value of KVP (P204) to keep the responsiveness of speed loop. However, when increasing the
setting value of KVP (P2-04), it may easily result in the vibration of machinery
system. Please use this parameter to suppress or eliminate the noise of
resonance. If the setting value of NLP is higher, the capability of improving the
noise of resonance is better. However, if the setting value is over high, it may
easily lead to the instability of speed loop and overshoot of machinery system.
The recommended setting value is as follows:

DST, Parameter P2-26 External Anti-Interference Gain
This parameter is used to enhance the anti-interference capability and reduce the
occurrence of overshoot. The default setting is 0 (Disabled). It is not
recommended to use it in manual mode only when performing a few tuning on the
value gotten through P2-32 AutoMode (PDFF) (setting value is 5, mode 5)
automatically (The setting value of P2-26 will change to the value that measured
in mode 5 (AutoMode (PDFF)) when switching mode 5 ((AutoMode (PDFF)) to
mode 0 (Manual mode)).

PFG, Parameter P2-02 Position Feed Forward Gain
This parameter is used to reduce position error and shorten the positioning
settling time. However, if the setting value is over high, it may easily lead to the
overshoot of machinery system. If the value of electronic gear ratio (1-44/1-45) is
over than 10, the machinery system may also easily generate vibration or noise.
5-22
Revision September 2013
Chapter 6 Control Modes of
Operation
6.1 Control Modes of Operation
The Delta ASDA-B2 series can be programmed to provide six single and five dual modes
of operation. Their operation and description is listed in the following table.
Mode
External Position Control
Speed Control
Internal Speed Control
Code
P
External Position control mode for the servo motor is
achieved via an external pulse command.
S
(External / Internal) Speed control mode for the servo
motor can be achieved via parameters set within the
controller or from an external analog -10 ~ +10 VDC
command. Control of the internal speed mode is via
the Digital Inputs (DI). (A maximum of three speeds
can be stored internally).
Sz
Internal Speed control mode for the servo motor is
only achieved via parameters set within the controller.
Control of the internal speed mode is via the Digital
Inputs (DI). (A maximum of three speeds can be
stored internally).
T
(External / Internal) Torque control mode for the servo
motor can be achieved via parameters set within the
controller or from an external analog -10 ~ +10 VDC
command. Control of the internal torque mode is via
the Digital Inputs (DI). (A maximum of three torque
levels can be stored internally).
Tz
Internal Torque control mode for the servo motor is
only achieved via parameters set within the controller.
Control of the internal torque mode is via the Digital
Inputs (DI). (A maximum of three torque levels can be
stored internally).
S-P
Either S or P control mode can be selected via the
Digital Inputs (DI)
T-P
Either T or P control mode can be selected via the
Digital Inputs (DI)
S-T
Either S or T control mode can be selected via the
Digital Inputs (DI)
Single
Mode
Torque Control
Internal Torque Control
Dual Mode
Revision September 2013
Description
6-1
Chapter 6 Control Modes of Operation
ASDA-B2
The steps of changing mode:
(1) Switching the servo drive to Servo Off status. Turning SON signal of Digit input to be
off can complete this action.
(2) Using parameter P1-01. (Refer to chapter 7).
(3) After the setting is completed, cut the power off and restart the drive again.
The following sections describe the operation of each control mode, including control
structure, command source and loop gain adjustment, etc.
6.2 Position Control Mode
The position control mode is usually used for the applications requiring precision
positioning, such as industry positioning machine, indexing table etc. The external pulse
train with direction which can control the rotation angle of servo motor. The max. input
frequency for the external pulse command is 4Mpps.
For the closed-loop positioning, speed control loop is the principal part and the auxiliary
parameters are position loop gain and feed forward compensation. The users can also
select two kinds of tuning mode (Manual/Auto modes) to perform gain adjustment. This
Section 6.2 mainly describes the applicability of loop gain adjustment and feed forward
compensation of Delta servo system.
6.2.1 Command Source of Position (PT) Control Mode
The command source of P mode is external pulse train input form terminals. There are
three types of pulse input and each pulse type is with·logic type (positive (+), negative
(-)). They all can be set in parameter P1-00. Please refer to the following relevant
parameters:
P1-00▲
PTT
External Pulse Input Type
Operation
Keypad/Software
Interface:
Communication
Address: 0100H
0101H
Related Section:
Section 6.2.1
Default: 0x2
Control
PT
Mode:
Unit: Range: 0 ~ 1142
Data Size: 16-bit
Display
Hexadecimal
Format:
Settings:
6-2
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
A: Input pulse type
0: AB phase pulse (4x) (Quadrature Input)
1: Clockwise (CW) + Counterclockwise(CCW) pulse
2: Pulse + Direction
3: Other settings:
B: Input pulse filter
This setting is used to suppress or reduce the chatter caused by the noise, etc.
However, if the instant input pulse filter frequency is over high, the frequency that
exceeds the setting value will be regarded as noise and filtered.
Setting Low-speed Filter Frequency Setting High-speed Filter Frequency
Value (Min. Filter Frequency (see note 1)) Value (Min. Filter Frequency (see note 1))
Revision September 2013
0
0.83Mpps (600ns)
0
3.33Mpps (150ns)
1
208Kpps (2.4us)
1
0.83Mpps (600ns)
2
104Kpps (4.8us)
2
416Kpps (1.2us)
3
52Kpps (9.6us)
3
208Kpps (2.4us)
4
No Filter Function
4
No Filter Function
6-3
Chapter 6 Control Modes of Operation
ASDA-B2
Please note:
1.
If an input pulse of 2~4MHz is used, it is recommended to change the setting value B (Input
pulse filter) and set this setting value to 4. Please note that this function is available for DSP
version V1.036 sub05, CPLD version V10 and later models only.
Note: If the signal is a 4Mpps high input pulse, setting the value B to 4 is able to ensure that the
signal will not be filtered and will be certainly delivered.
6-4
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
C: Input polarity
Logic
Pulse
Type
Forward
Reverse
AB
phase
pulse
T3
Positive
0
Logic
TH
CW +
CCW
pulse
TH
Pulse
T2
T2
T2
T2
T2
T2
Sign
Pulse +
Direction
Pulse
AB
phase
pulse
TH
T1
Sign
T1
T1
T1 T1
T1
CW +
Negative
CCW
1
Logic
pulse
Pulse
TH
Pulse +
Direction
T4
T5
T6
T5
T6
T5
T4
Sign
Pulse specification
High-speed
pulse
Low-speed
pulse
Revision September 2013
Max.
input
pulse
frequency
Min. time width
T1
T2
T3
T4
T5
T6
Line
driver
4Mpps
62.5ns
125ns
250ns
200ns
125ns
125ns
Line
driver
500Kpps
0.5μs
1μs
2μs
2μs
1μs
1μs
Open
collector
200Kpps
1.25μs
2.5μs
5μs
5μs
2.5μs
2.5μs
6-5
Chapter 6 Control Modes of Operation
Max. input pulse
frequency
Voltage
specification
Forward
specification
Line driver
4Mpps
5V
< 25mA
Line driver
500Kpps
2.8V ~ 3.7V
< 25mA
Open collector
200Kpps
24V (Max.)
< 25mA
Pulse specification
High-speed pulse
ASDA-B2
Low-speed pulse
D: Source of pulse command
Setting value
0
1
Input pulse interface
Remark
CN1 Terminal Identification:
Open collector for low-speed pulse PULSE, SIGN
Line driver for high-speed pulse
CN1 Terminal Identification:
PULSE_D, SIGN_D
Position pulse can be input from these terminals, /PULSE (41), PULSE (43), HPULSE (38),
/HPULSE (36), /SIGN (37), SIGN (39) and HSIGN (42), /HSIGN (40). It can be an open-collector
circuit or line driver circuit. For the detail wiring, please refer to 3.6.1.
6.2.2 Structure of Position Control Mode
Basic Structure:
In order to pursue the goal of perfection in position control, the pulse signal should be
modified through position command processing and the structure is shown as the
figure below:
6-6
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
Using parameter P1-01 can select P mode. Electronic gear ratio can be set in P
modes to set proper position revolution. ASDA-B2 series servo drive also provides
low-pass filter, which are used whenever the motor and load need to be operated more
smoothly. As for the information of electronic gear ratio, and low-pass filter, please
refer to the following sections 6.2.3 and 6.2.4.
Pulse Inhibit Input Function (INHP)
INHP is activated via digital inputs (Please refer to parameter P2-10 ~ P2-17,P2-36
and DI INHP(07) in Table 7.1).When the drive is in position mode, if INHP is activated,
the external pulse input command is not valid and the motor will stop.
6.2.3 Electronic Gear Ratio
Relevant parameters:
P1-44▲
GR1
Electronic Gear Ratio (1st Numerator) (N1)
Operation
Keypad/Software
Interface:
Communication
Address: 0158H
0159H
Related Section:
Section 6.2.3
Default: 16
Control
PT
Mode:
Unit: pulse
Range: 1 ~ (226-1)
Data Size: 32-bit
Display
Decimal
Format:
Settings:
This parameter is used to set the numerator of the electronic gear ratio. The
denominator of the electronic gear ratio is set by P1-45. P2-60 ~ P2-62 are used to
set the additional numerators.
Revision September 2013
6-7
Chapter 6 Control Modes of Operation
ASDA-B2
Please note:
1. In PT mode, the setting value of P1-44 can be changed only when the servo
drive is enabled (Servo On).
P1-45▲
GR2
Electronic Gear Ratio (Denominator) (M)
Operation
Keypad/Software
Interface:
Communication
Address: 015AH
015BH
Related Section:
Section 6.2.3
Default: 10
Control
PT
Mode:
Unit: pulse
Range: 1 ~ (231-1)
Data Size: 32-bit
Display
Decimal
Format:
Settings:
This parameter is used to set the denominator of the electronic gear ratio. The
numerator of the electronic gear ratio is set by P1-44. P2-60 ~ P2-62 are used to set
the additional numerators.
As the wrong setting may cause motor to run chaotically (out of control) and it may
lead to personnel injury, therefore, ensure to observe the following rule when setting
P1-44, P1-45.
The electronic gear ratio setting (Please also see P1-44, P2-60 ~ P2-62):
Pulse input
f1
N
M
Position
command
N
f2 = f1 x M
f1: Pulse input
f2: Position command
N: Numerator, the setting value of P1-44 or
P2-60 ~ P2-62
M: Denominator, the setting value of P1-45
The electronic gear ratio setting range must be within: 1/50<N/M<25600.
Please note:
1. In PT mode, the setting value of P1-45 can not be changed when the servo drive
is enabled (Servo On).
The electronic gear function provides easy travel distance ratio change. However, the over
high electronic gear ratio will command the motor to move not smoothly. At this time, the users
can use low-pass filter parameter to improve this kind of situation. For example, assume that
the electronic gear ratio is equal to 1 and the encoder pulse per revolution is 10000ppr, if the
electronic gear ratio is changed to 0.5, then the motor will rotate one pulse when the command
from external controller is two pulses.
For example, after the proper electronic gear ratio is set, the reference travel distance is 1
m/pulse, the machinery will become easier to be used.
6-8
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
Electronic Gear Ratio
When the electronic
gear ratio is not
used
=
When the electronic
gear ratio is used
=
1
1
1000 0
300 0
Corresponding travel distance per
pulse
=
3x 100 0
300 0
=
4x 250 0 100 00
m
=1 m
6.2.4 Low-pass Filter
Relevant parameters:
P1-08
PFLT
Smooth Constant of Position Command (Low- Address: 0110H
pass Filter)
0111H
Operation
Keypad/Software
Interface:
Communication
Related Section:
Section 6.2.4
Default: 0
Control
PT
Mode:
Unit: 10ms
Range: 0 ~ 1000
Data Size: 16-bit
Display
Decimal
Format:
Settings: 0: Disabled
For example: 11=110 msec
Position
Tar get pos ition
Time (ms)
PF LT
Revision September 2013
6-9
Chapter 6 Control Modes of Operation
ASDA-B2
6.2.5 Position Loop Gain Adjustment
Before performing position control (setting position control block diagram), the users
should complete the speed control setting by using Manual mode (parameter P-32)
since the position loop contains speed loop. Then, adjust the Proportional Position
Loop Gain, KPP (parameter P2-00) and Position Feed Forward Gain, PFG (parameter
P2-02). Or use Auto mode to adjust the gain of speed and position control block
diagram automatically.
1) Proportional Position Loop Gain: To increase this gain can enhance the position
loop responsiveness.
2) Position Feed Forward Gain: To increase this gain can reduce the position track
error during operation.
The position loop responsiveness cannot exceed the speed loop responsiveness, and
it is recommended that the speed loop responsiveness should be at least four times
faster than the position loop responsiveness. This also means that the setting value of
Proportional Speed Loop Gain, KVP should be at least four times faster than
Proportional Position Loop Gain, KPP.
The equation is shown as follows:
fp < fv
4 , fv : Speed Loop Responsiveness (Hz), fp : Position Loop Responsiveness (Hz)
KPP = 2 ×  × fp.
For example, the desired position loop responsiveness is equal to 20 Hz.
Then, KPP = 2 ×  × 20= 125 rad/s.
Relevant parameters:
P2-00
KPP
Proportional Position Loop Gain
Operation
Keypad/Software
Interface:
Communication
Address: 0200H
0201H
Related Section:
Section 6.2.5
Default: 35
Control
PT
Mode:
Unit: rad/s
Range: 0 ~ 2047
Data Size: 16-bit
Display
Decimal
Format:
Settings:
This parameter is used to set the position loop gain. It can increase stiffness,
expedite position loop response and reduce position error. However, if the setting
value is over high, it may generate vibration or noise.
6-10
Revision September 2013
ASDA-B2
P2-02
Chapter 6 Control Modes of Operation
PFG
Position Feed Forward Gain
Operation
Keypad/Software
Interface:
Communication
Address: 0204H
0205H
Related Section:
Section 6.2.5
Default: 50
Control
PT
Mode:
Unit: %
Range: 0 ~ 100
Data Size: 16-bit
Display
Decimal
Format:
Settings:
This parameter is used to set the feed forward gain when executing position control
command. When using position smooth command, increase gain can improve
position track deviation. When not using position smooth command, decrease gain
can improve the resonance condition of mechanical system.
When the value of Proportional Position Loop Gain, KPP is too great, the position loop
responsiveness will be increased and it will result in small phase margin. If this
happens, the rotor of motor will oscillate. At this time, the users have to decrease the
value of KPP until the rotor of motor stop oscillating. When there is an external torque
command interrupted, over low KPP value will let the motor cannot overcome the
external strength and fail to meet the requirement of reasonable position track error
demand. Adjust feed forward gain, PFG (P2-02) to efficiently reduce the dynamic
position track error.
Revision September 2013
6-11
Chapter 6 Control Modes of Operation
ASDA-B2
6.3 Speed Control Mode
The speed control mode (S or Sz) is usually used on the applications of precision speed
control, such as CNC machine, etc. ASDA-B2 series servo drive supports two kinds of
command sources in speed control mode. One is external analog signal and the other is
internal parameter. The external analog signal is from external voltage input and it can
control the speed of servo motor. There are two usage of internal parameter, one is set
different speed command in three speed control parameters before operation and then
using SPD0 and SPD1 of CN1 DI signal perform switching. The other usage is using serial
communication to change the setting value of parameter.
Beside, in order to make the speed command switch more smoothly, ASDA-B2 series
servo drive also provides complete S-curve profile for speed control mode. For the closedloop speed control, ASDA-B2 series servo drive provides gain adjustment function and an
integrated PI or PDFF controller. Besides, two modes of tuning technology (Manual/Auto)
are also provided for the users to select (parameter P2-32).
There are two turning modes for gain adjustment: Manual and Auto modes.

Manual Mode: User-defined loop gain adjustment. When using this mode, all auto
and auxiliary function will be disabled.

Auto Mode: Continuous adjustment of loop gains according to measured inertia, with
ten levels of system bandwidth. The parameter set by user is default value.
6.3.1 Command Source of Speed Control Mode
Speed command Sources:
1) External analog signal: External analog voltage input, -10V to +10V
2) Internal parameter: P1-09 to P1-11
6-12
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
Speed
Command
S1
CN1 DI
Signal
SPD
1
0
SPD
0
0
S2
0
1
S3
1
0
S4
1
1
Command Source
Mode
Content
Range
S
External
analog
signal
Voltage between VREF-GND
Sz
N/A
Speed command is 0
0
P1-09
-50000 ~
50000
P1-10
-50000 ~
50000
P1-11
-50000 ~
50000
Internal parameter
+/-10 V

State of SPD0~1: 0: indicates OFF (Normally Open); 1: indicates ON (Normally
Closed)

When SPD0 and SPD1 are both = 0 (OFF), if the control mode of operation is
Sz, then the speed command is 0. Therefore, if the users do not use analog
voltage as speed command, the users can choose Sz mode and avoid the zero
point drift problem of analog voltage signal. If the speed control mode is S mode,
then the command is the analog voltage between V-REF and GND. The setting
range of the input voltage is from -10V to +10V and the corresponding motor
speed is adjustable (Please see parameter P1-40).

When at least one of SPD0 and SPD1 is not 0 (OFF), the speed command is
internal parameter (P1-09 to P1-11). The command is valid (enabled) after
either SPD0 or SPD1 is changed.

The range of internal parameters is within -50000 ~ +50000 r/min. Setting value
= Range x Unit (0.1 r/min). For example, if P1-09 is set to +30000, the setting
value = +30000 x 0.1 r/min = +3000 r/min.
The speed command that is described in this section not only can be taken as speed
command in speed control mode (S or Sz mode) but also can be the speed limit input
command in torque control mode (T or Tz mode).
Revision September 2013
6-13
Chapter 6 Control Modes of Operation
ASDA-B2
6.3.2 Structure of Speed Control Mode
Basic Structure:
In the figure above, the speed command processing is used to select the command
source of speed control according to chapter 6.3.1, including proportional gain (P1-40)
and S-curve filter smoothing strategy of speed control. The speed control block
diagram is used to manage the gain parameters of the servo drive and calculate the
current input provided to motor instantaneously. The resonance suppression block
diagram is used to suppress the resonance of mechanical system.
The function and structure of speed command processing is shown as the figure below:
The command source is selected according to the state of SPD0, SPD1 and
parameter P1-01 (S or Sz). Whenever the command signal needs to be more smoothly,
we recommend the users to use S-curve and low-pass filter.
6-14
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
6.3.3 Smoothing Strategy of Speed Control Mode
S-curve Filter
The S-curve filter is a speed smoothing command which provides 3 steps accel / decel
S-curve to smooth the speed command change of the motor during acceleration and
deceleration. Using S-curve filter can let the servo motor run more smoothly in
response to a sudden speed command change. Since the speed and acceleration
curve are both continuous, in order to avoid the mechanical resonance and noise may
occur due to a sudden speed command (differentiation of acceleration), using S-curve
filter not only can improve the performance when servo motor accelerate or decelerate
but also can make the motor run more smoothly. S-curve filter parameters include P134 Acceleration Time (TACC), P1-35 Deceleration Time (TDEC) and Accel /Decel Scurve (TSL), and the users can use these three parameters to improve the motor
performance during acceleration, deceleration and operation. ASDA-B2 series servo
drives also support the time calculation of completing speed command. T (ms) is the
operation (running) time. S (r/min) is absolute speed command, i.e. the absolute value
(the result) after starting speed subtracts the final speed.
Relevant parameters:
P1-34
Address: 0144H
0145H
TACC Acceleration Time
Operation
Keypad/Software
Interface:
Communication
Related Section:
Section 6.3.3
Default: 200
Control
S
Mode:
Unit: ms
Range: 1 ~ 20000
Data Size: 16-bit
Revision September 2013
6-15
Chapter 6 Control Modes of Operation
ASDA-B2
Display
Decimal
Format:
Settings:
This parameter is used to determine the acceleration time to accelerate from 0 to its
rated motor speed. The functions of parameters P1-34, P1-35 and P1-36 are each
individual.
Please note:
1. When the source of speed command is analog command, the maximum setting
value of P1-36 is set to 0, the acceleration and deceleration function will be
disabled.
P1-35
TDEC
Address: 0146H
0147H
Deceleration Time
Operation
Keypad/Software
Interface:
Communication
Related Section:
Section 6.3.3
Default: 200
Control
S
Mode:
Unit: ms
Range: 1 ~ 20000
Data Size: 16-bit
Display
Decimal
Format:
Settings:
This parameter is used to determine the acceleration time to accelerate from 0 to its
rated motor speed. The functions of parameters P1-34, P1-35 and P1-36 are each
individual.
Please note:
1. When the source of speed command is analog command, the maximum setting
value of P1-36 is set to 0, the acceleration and deceleration function will be
disabled.
P1-36
TSL
Address: 0148H
0149H
Accel /Decel S-curve
Operation
Keypad/Software
Interface:
Communication
Related Section:
Section 6.3.3
Default: 0
Control
S
Mode:
Unit: ms
Range: 0 ~ 10000 (0: Disabled)
Data Size: 16-bit
Display
Decimal
Format:
6-16
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
Settings:
This parameter is used to make the motor run more smoothly when startup and
windup. Using this parameter can improve the motor running stability.
TACC: P1-34, Acceleration time
TDEC: P1-35, Deceleration time
TSL: P1-36, Accel /Decel S-curve
Total acceleration time = TACC + TSL
Total deceleration time = TDEC + TSL
The functions of parameters P1-34, P1-35 and P1-36 are each individual. When P136 is set to 0 (Disabled), the settings of P1-34, P1-35 are still effective. It indicates
that the parameters P1-34 and P1-35 will not become disabled even when P1-36 is
disabled.
Please note:
1. When the source of speed command is analog command, the maximum setting
value of P1-36 is set to 0, the acceleration and deceleration function will be
disabled.
Analog Speed Command S-curve Filter
ASDA-B2 series servo drives also provide Analog Speed Command S-curve Filter for
the smoothing in response to a sudden analog input signal.
Speed (rpm)
Analog speed command
Motor Torque
3000
0
1
2
3
4
5
6
7
8
9
Time (sec)
-3000
The analog speed command S-curve filter is for the smoothing of analog input signal
and its function is the same as the S-curve filter. The speed and acceleration curve of
analog speed command S-curve filter are both continuous. The above figure shows
the curve of analog speed command S-curve filter and the users can see the ramp of
speed command is different during acceleration and deceleration. Also, the users can
see the difference of input command tracking and can adjust time setting by using
parameter P1-34, P1-35, P1-36 to improve the actual motor performance according to
Revision September 2013
6-17
Chapter 6 Control Modes of Operation
ASDA-B2
actual condition.
Analog Speed Command Low-pass Filter
Analog Speed Command Low-pass Filter is used to eliminate high frequency response
and electrical interference from an analog speed command and it is also with
smoothing function.
Relevant parameters:
P1-06
SFLT
Accel / Decel Smooth Constant of Analog
Speed Command (Low-pass Filter)
Operation
Keypad/Software
Interface:
Communication
Address: 010CH
010DH
Related Section:
Section 6.3.3
Default: 0
Control
S
Mode:
Unit: ms
Range: 0 ~ 1000 (0: Disabled)
Data Size: 16-bit
Display
Decimal
Format:
Settings: 0: Disabled
NOTE
1) If the setting value of parameter P1-06 is set to 0, it indicates the function of this
parameter is disabled and the command is just By-Pass.
Target Speed
SFLT
6-18
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
6.3.4 Analog Speed Input Scaling
The analog voltage between V_REF and GND determines the motor speed command.
Using with parameter P1-40 (Max. Analog Speed Command) can adjust the speed
control ramp and its range.
5000rpm
The speed control ramp is
determined by parameter P1-40
3000rpm
-10
-5
5
10
Analog Input Voltage (V)
-3000rpm
-5000rpm
Relevant parameters:
P1-40▲
VCM
Max. Analog Speed Command or Limit
Operation
Keypad/Software
Interface:
Communication
Address: 0150H
0151H
Related Section:
Section 6.3.4
Default: rated speed
Control
S, T
Mode:
Unit: r/min
Range: 0 ~ 10000
Data Size: 16-bit
Display
Decimal
Format:
Settings:
In Speed mode, this parameter is used to set the maximum analog speed command
based on the maximum input voltage (10V).
In Torque mode, this parameter is used to set the maximum analog speed limit
based on the maximum input voltage (10V).
For example, in speed mode, if P1-40 is set to 3000 and the input voltage is 10V, it
indicates that the speed command is 3000 r/min. If P1-40 is set to 3000, but the input
voltage is changed to 5V, then the speed command is changed to 1500 r/min.
Speed Command / Limit = Input Voltage Value x Setting value of P1-40 / 10
Revision September 2013
6-19
Chapter 6 Control Modes of Operation
ASDA-B2
6.3.5 Timing Chart of Speed Control Mode
S4 (P1-11)
Internal speed
command
S3 (P1-10)
S2 (P1-09)
External analog
voltage or zero (0)
External I/O signal
S1
SPD0
OFF
SPD1
OFF
SON
ON
OFF
ON
ON
ON
NOTE
1) OFF indicates normally open and ON indicates normally closed.
2) When speed control mode is Sz, the speed command S1=0; when speed control mode is
S, the speed command S1 is external analog voltage input (Please refer to P1-01).
3) After Servo ON, the users can select command according to the state of SPD0~1.
6.3.6 Speed Loop Gain Adjustment
The function and structure of speed control mode is shown as the figure below:
6-20
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
There are two turning modes of gain adjustment: Manual and Auto modes. The gain of
ASDA-B2 series servo drives can be adjusted by using any one of three tuning modes.

Manual Mode: User-defined loop gain adjustment. When using this mode, all
auto and auxiliary function will be disabled.

Auto Mode: Continuous adjustment of loop gains according to measured inertia,
with ten levels of system bandwidth. The parameter set by user is default value.
The mode of gain adjustment can be selected by parameter P2-32:
P2-32▲
AUT2
Address: 0240H
0241H
Tuning Mode Selection
Operation
Keypad/Software
Interface:
Communication
Default: 0
Related Section:
Section 5.6,
Section 6.3.6
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 2
Data Size: 16-bit
Display
Hexadecimal
Format:
Settings:
0: Manual mode
1: Auto Mode [Continuous adjustment]
2: Semi-Auto Mode [Non-continuous adjustment]
Explanation of manual mode:
1. When P2-32 is set to mode#0, the setting value of P2-00, P2-02, P2-04, P2-06,
P2-07, P2-25 and P2-26 can be user-defined. When switching mode #1 or #2 to
#0, the setting value of P2-00, P2-02, P2-04, P2-06, P2-07, P2-25 and P2-26 will
change to the value that measured in #1 auto-tuning mode or #2 semi-auto
tuning mode.
Explanation of auto-tuning mode:
The servo drive will continuously estimate the system inertia, save the measured
load inertia value automatically and memorized in P1-37 every 30 minutes by
referring to the frequency response settings of P2-31.
1. When switching mode #1 or #2 to #0, the servo drive will continuously estimate
the system inertia, save the measured load inertia value automatically and
memorized in P1-37. Then, set the corresponding parameters according to this
measured load inertia value.
2. When switching mode#0 or #1 to #2, enter the appropriate load inertia value in
P1-37.
3. When switching mode#1 to #0, the setting value of P2-00, P2-04 and P2-06 will
change to the value that measured in #1 auto-tuning mode.
Revision September 2013
6-21
Chapter 6 Control Modes of Operation
ASDA-B2
Explanation of semi-auto tuning mode:
1. When switching mode #2 to #0, the setting value of P2-00, P2-04, P2-06, P2-25
and P2-26 will change to the value that measured in #1 auto-tuning mode.
2. After the system inertia becomes stable (The displau of P2-33 will show 1), it will
stop estimating the system inertia, save the measured load inertia value
automatically, and memorized in P1-37. However, when P2-32 is set to mode#1
or #2, the servo drive will continuously perform the adjustment for a period of time.
3. When the value of the system inertia becomes over high, the display of P2-33 will
show 0 and the servo drive will start to adjust the load inertia value continuously.
Manual Mode
When Tuning Mode Settings of P2-32 is set to 0, the users can define the proportional
speed loop gain (P2-04), speed integral gain (P2-06) feed forward gain (P2-07) and
ratio of load inertia to servo motor Inertia (1-37). Please refer to the following
description:

Proportional gain:
responsiveness.

Integral gain: Adjust this gain can enhance the low-frequency stiffness of speed
loop and eliminate the steady error. Also, reduce the value of phase margin.
Over high integral gain will result in the unstable servo system.

Feed forward gain: Adjust this gain can decrease the phase delay error
Adjust
this
gain
can
increase
the
position
loop
Relevant parameters:
P2-04
KVP
Proportional Speed Loop Gain
Operation
Keypad/Software
Interface:
Communication
Address: 0208H
0209H
Related Section:
Section 6.3.6
Default: 500
Control
ALL
Mode:
Unit: rad/s
Range: 0 ~ 8191
Data Size: 16-bit
Display
Decimal
Format:
Settings:
This parameter is used to set the speed loop gain. When the value of proportional
speed loop gain is increased, it can expedite speed loop response. However, if the
setting value is over high, it may generate vibration or noise.
6-22
Revision September 2013
ASDA-B2
P2-06
Chapter 6 Control Modes of Operation
KVI
Speed Integral Compensation
Operation
Keypad/Software
Interface:
Communication
Address: 020CH
020DH
Related Section:
Section 6.3.6
Default: 100
Control
ALL
Mode:
Unit: rad/s
Range: 0 ~ 1023
Data Size: 16-bit
Display
Decimal
Format:
Settings:
This parameter is used to set the integral time of speed loop. When the value of
speed integral compensation is increased, it can improve the speed response ability
and decrease the speed control deviation. However, if the setting value is over high,
it may generate vibration or noise.
P2-07
KVF
Speed Feed Forward Gain
Operation
Keypad/Software
Interface:
Communication
Address: 020EH
020FH
Related Section:
Section 6.3.6
Default: 0
Control
ALL
Mode:
Unit: %
Range: 0 ~ 100
Data Size: 16-bit
Display
Decimal
Format:
Settings:
This parameter is used to set the feed forward gain when executing speed control
command.
When using speed smooth command, increase gain can improve speed track
deviation.
When not using speed smooth command, decrease gain can improve the resonance
condition of mechanical system.
In theory, stepping response can be used to explain proportional gain (KVP), integral
gain (KVI) and feed forward gain (KVF). Now we use frequency area and time area
respectively to explain the logic.
Revision September 2013
6-23
Chapter 6 Control Modes of Operation
ASDA-B2
Frequency Domain
6-24
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
Time Domain
In general, the equipment, such as spectrum analyzer is needed and used to analyze
when using frequency domain method and the users also should have this kind of
Revision September 2013
6-25
Chapter 6 Control Modes of Operation
ASDA-B2
analysis technology. However, when using time domain method, the users only need
to prepare an oscilloscope. Therefore, the general users usually use time domain
method with the analog DI/DO terminal provided by the servo drive to adjust what is
called as PI (Proportional and Integral) type controller. As for the performance of
torque shaft load, input command tracking and torque shaft load have the same
responsiveness when using frequency domain method and time domain method. The
users can reduce the responsiveness of input command tracking by using input
command low-pass filter.
Auto Mode (Continuous adjustment))
This Auto Mode provides continuous adjustment of loop gains according to measured
inertia automatically. It is suitable when the load inertia is fixed or the load inertia
change is small and is not suitable for wide range of load inertia change. The period of
adjustment time is different depending on the acceleration and deceleration of servo
motor. To change the stiffness and responsiveness, please use parameter P2-31.
Motor Speed
W
Inertia Measurement
J
6-26
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
6.3.7 Resonance Suppression
The resonance of mechanical system may occur due to excessive system stiffness or
frequency response. However, this kind of resonance condition can be improved,
suppressed, even can be eliminated by using low-pass filter (parameter P2-25) and
notch filter (parameter P2-23, P2-24) without changing control parameter.
Relevant parameters:
P2-23
NCF1
Notch Filter 1 (Resonance Suppression)
Operation
Keypad/Software
Interface:
Communication
Address: 022EH
022FH
Related Section:
Section 6.2.5
Default: 1000
Control
ALL
Mode:
Unit: Hz
Range: 50 ~ 2000
Data Size: 16-bit
Display
Decimal
Format:
Settings:
This parameter is used to set first resonance frequency of mechanical system. It can
be used to suppress the resonance of mechanical system and reduce the vibration of
mechanical system.
If P2-24 is set to 0, this parameter is disabled.
The parameters P2-23 and P2-24 are the first group of notch filter parameters and
the parameters P2-43 and P2-44 are the second group of notch filter parameters.
P2-24
DPH1
Notch Filter Attenuation Rate 1
(Resonance Suppression)
Operation
Keypad/Software
Interface:
Communication
Address: 0230H
0231H
Related Section:
Section 6.3.7
Default: 0
Control
ALL
Mode:
Unit: dB
Range: 0 ~ 32 (0: Disabled)
Data Size: 16-bit
Display
Decimal
Format:
Settings:
This parameter is used to set magnitude of the resonance suppression that is set by
parameter P2-23. If P2-24 is set to 0, the parameters P2-23 and P2-24 are both
disabled.
Revision September 2013
6-27
Chapter 6 Control Modes of Operation
ASDA-B2
The parameters P2-23 and P2-24 are the first group of notch filter parameters and
the parameters P2-43 and P2-44 are the second group of notch filter parameters.
P2-43
NCF2
Notch Filter 2 (Resonance Suppression)
Operation
Keypad/Software
Interface:
Communication
Address: 0256H
0257H
Related Section:
Section 6.3.7
Default: 1000
Control
ALL
Mode:
Unit: Hz
Range: 50 ~ 2000
Data Size: 16-bit
Display
Decimal
Format:
Settings:
This parameter is used to set second resonance frequency of mechanical system. It
can be used to suppress the resonance of mechanical system and reduce the
vibration of mechanical system.
If P2-43 is set to 0, this parameter is disabled.
The parameters P2-23 and P2-24 are the first group of notch filter parameters and
the parameters P2-43 and P2-44 are the second group of notch filter parameters.
P2-44
DPH2
Notch Filter Attenuation Rate 2
(Resonance Suppression)
Operation
Keypad/Software
Interface:
Communication
Address: 0258H
0259H
Related Section:
Section 6.3.7
Default: 0
Control
ALL
Mode:
Unit: dB
Range: 0 ~ 32
Data Size: 16-bit
Display
Decimal
Format:
Settings:
This parameter is used to set magnitude of the resonance suppression that is set by
parameter P2-43. If P2-44 is set to 0, the parameters P2-43 and P2-44 are both
disabled.
6-28
Revision September 2013
ASDA-B2
P2-45
Chapter 6 Control Modes of Operation
NCF3
Notch Filter 3 (Resonance Suppression)
Operation
Keypad/Software
Interface:
Communication
Address: 025AH
025BH
Related Section:
Section 6.3.7
Default: 1000
Control
ALL
Mode:
Unit: Hz
Range: 50 ~ 2000
Data Size: 16-bit
Display
Decimal
Format:
Settings:
This parameter is used to set third resonance frequency of mechanical system. It can
be used to suppress the resonance of mechanical system and reduce the vibration of
mechanical system.
If P2-45 is set to 0, this parameter is disabled.
P2-46
DPH3
Notch Filter Attenuation Rate 3
(Resonance Suppression)
Operation
Keypad/Software
Interface:
Communication
Address: 025CH
025DH
Related Section:
Section 6.3.7
Default: 0
Control
ALL
Mode:
Unit: dB
Range: 0 ~ 32
Data Size: 16-bit
Display
Decimal
Format:
Settings:
This parameter is used to set magnitude of the resonance suppression that is set by
parameter P2-45. If P2-46 is set to 0, the parameters P2-45 and P2-46 are both
disabled.
P2-25
NLP
Low-pass Filter Time Constant
(Resonance Suppression)
Operation
Keypad/Software
Interface:
Default: 0.2 (1kW and below
models) or 0.5 (other
models)
Communication
Address: 0232H
0233H
Related Section:
Section 6.3.7
2 (1kW and below
models) or 5 (other
models)
Control
ALL
Mode:
Revision September 2013
6-29
Chapter 6 Control Modes of Operation
Unit: 1ms
Range: 0.0 ~ 100.0
ASDA-B2
0.1ms
0 ~ 1000
Data Size: 16-bit
Display
One-digit
Format:
Input Value
1.5 = 1.5 ms
Example:
Decimal
15 = 1.5 ms
Settings:
This parameter is used to set low-pass filter time constant of resonance suppression.
If P2-25 is set to 0, this parameter is disabled.
There are two groups of notch filters provided by ASDA-A2 series. The first group of notch filter is
P2-43 and P2-44, and the second group of notch filter is P2-45 and P2-46. When there is
resonance, please set P2-47 to 1 or 2 (Auto mode), and then the servo drive will find resonance
frequency and suppress the resonance automatically. After suppressing the resonance point, the
system will memorize the notch filter frequency into P2-43 and P-45, and memorize the notch filter
attenuation rate into P2-44 and P2-46.
When P2-47 is set to 1, the resonance suppression will be enabled automatically. After the
mechanical system becomes stable (approximate 20 minutes), the setting value of P2-47 will
return to 0 (Disable auto resonance suppression function). When P2-47 is set to 2, the system will
find the resonance point continuously even after the mechanical system becomes stable.
When P2-47 is set to 1 or 2, if the resonance conditions can not be eliminated, we recommend the
users to check the settings of P2-44 and P2-46. If either of the setting value of P2-44 and P2-46 is
set to 32, please decrease the speed frequency response and estimate the resonance point again.
If the resonance conditions can not be eliminated when the setting values of P2-44 and P2-46 are
both less than 32, please set P2-47 to 0 first, and increase the setting value of P2-44 and P2-46
manually. If the resonance exists still after increasing the setting value of P2-44 and P2-46, please
decrease the value of speed frequency response again and then use the resonance suppression
function again.
6-30
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
When increasing the setting value of P2-44 and P2-46 manually, ensure to pay close attention on
the setting value of P2-44 and P2-46. If the value of P2-44 and P2-46 is greater than 0, it indicates
that the corresponding resonance frequency of P2-43 and P2-45 is found through auto resonance
suppression function. If the value of P2-44 and P2-46 is equal to 0, it indicates that the value of P243 and P2-45 will be the default value 1000 and this is not the frequency found by auto resonance
suppression function. At this time, if the users increase the value of notch filter attenuation rate
which does not exist, the performance of the current mechanical system may deteriorate.
Settings of P2-47
Current Value
Desired Value
0
1
0
2
1
0
1
1
1
2
2
0
2
1
2
2
Revision September 2013
Function
Clear the setting value of P2-43 ~ P2-46 and enable
auto resonance suppression function.
Clear the setting value of P2-43 ~ P2-46 and enable
auto resonance suppression function.
Save the setting value of P2-43 ~ P2-46 and disable
auto resonance suppression function.
Clear the setting value of P2-43 ~ P2-46 and enable
auto resonance suppression function.
Do not clear the setting value of P2-43 ~ P2-46 and
enable auto resonance suppression function
continuously.
Save the setting value of P2-43 ~ P2-46 and disable
auto resonance suppression function.
Clear the setting value of P2-43 ~ P2-46 and enable
auto resonance suppression function.
Do not clear the setting value of P2-43 ~ P2-46 and
enable auto resonance suppression function
continuously.
6-31
Chapter 6 Control Modes of Operation
ASDA-B2
Flowchart of auto resonance suppression operation:
6-32
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
Low-pass filter
Please use parameter P2-25. The figure below shows the resonant open-loop gain.
Gain
Frequency
When the low-pass filter (parameter P2-25) is adjusted from 0 to high value, the value
of Low-pass frequency (BW) will become smaller (see the figure below). The resonant
condition is improved and the frequency response and phase margin will also
decrease.
Gain
0dB
BW
Frequency
Notch Filter
Usually, if the users know the resonance frequency, we recommend the users can
eliminate the resonance conditions directly by using notch filter (parameter P2-23, P224). However, the range of frequency setting is from 50 to 1000Hz only and the range
of resonant attenuation is 0~32 dB only. Therefore, if the resonant frequency is out of
this range, we recommend the users to use low-pass filter (parameter P2-25) to
improve resonant condition.
Please refer to the following figures and explanation to know how to use notch filter
and low-pass filter to improve resonant condition.
Revision September 2013
6-33
Chapter 6 Control Modes of Operation
ASDA-B2
Use Notch Filter to suppress resonance
Resonance
Point
Gain
Gain
Notch Filter
Resonance
conditions
is suppressed
0db
Low-pass
Frequency
Resonance
Frequency .
Gain
Low-pass
Frequency
Attenuation
Rate P2-24
Frequency
Resonance
Frequency .
Frequency
Resonance
Frequency
P2-23
Frequency
Use Low-pass Filter to suppress resonance
.
Resonance
Point
Gain
Low-pass
Frequency
Resonance
Frequency
Frequency
Gain
0db
Low-pass Filter
Attenuation
Rate -3db
Cut-off Frequency
of Low-pass Filter
= 10000 / P2-25
Hz
Frequency
Gain
Resonance
conditions
is suppressed
Low-pass
Frequency
Resonance
Frequency .
Frequency
When the low-pass filter (parameter P2-25) is adjusted from 0 to high value, the value
of Low-pass frequency will become smaller (see the figure on page 6-26). The
resonant condition is improved but the frequency response and phase margin will also
decrease and the system may become unstable. Therefore, if the users know the
resonance frequency, the users can eliminate the resonance conditions directly by
using notch filter (parameter P2-23, P2-24). Usually, if the resonant frequency can be
recognized, we recommend the users can directly use notch filter (parameter P2-23,
P2-24) to eliminate the resonance. However, if the resonant frequency will drift or drift
out of the notch filter range, we recommend the users not to use notch filter and use
low-pass filter to improve resonant conditions.
6-34
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
6.4 Torque Control Mode
The torque control mode (T or Tz) is usually used on the applications of torque control,
such as printing machine, spinning machine, twister, etc. Delta ASDA-B2 series servo
drive supports two kinds of command sources in torque control mode. One is external
analog signal and the other is internal parameter. The external analog signal is from
external voltage input and it can control the torque of servo motor. The internal parameters
are from P1-12 to P1-14 which are used to be the torque command in torque control mode.
6.4.1 Command Source of Torque Control Mode
Torque command Sources:
1) External analog signal: External analog voltage input, -10V to +10V
2) Internal parameter: P1-12 to P1-14
The command source selection is determined by the DI signal of CN1 connector.
Torque
Command
DI signal of
CN1
Command Source
Content
Range
TCM1 TCM0
T1
0
0
Mode
T
Tz
T2
0
1
T3
1
0
T4
1
1
External analog
signal
None
Internal parameter
Voltage between
T-REF-GND
Torque command is 0
+/- 10 V
0
P1-12
+/- 300 %
P1-13
+/- 300 %
P1-14
+/- 300 %

State of TCM0~1: 0: indicates OFF (Normally Open); 1: indicates ON (Normally
Closed)

When TCM0 and TCM1 are both 0 (OFF), if the control mode of operation is Tz,
then the command is 0. Therefore, if the users do not use analog voltage as
torque command, the users can choose Tz mode to operation torque control to
avoid the zero point drift problem of analog voltage. If the control mode of
operation is T, then the command is the analog voltage between T-REF and
GND. The setting range of the input voltage is from -10V to +10V and the
corresponding torque is adjustable (see parameter P1-41).

When at least one of TCM0 and TCM1 is not 0 (OFF), the torque command is
internal parameter. The command is valid (enabled) after either TCM0 or TCM1
is changed.
The torque command that is described in this section not only can be taken as torque
command in torque control mode (T or Tz mode) but also can be the torque limit input
command in position mode (P mode) and speed control mode (S or Sz mode).
Revision September 2013
6-35
Chapter 6 Control Modes of Operation
ASDA-B2
6.4.2 Structure of Torque Control Mode
Basic Structure:
The toque command processing is used to select the command source of torque
control according to chapter 6.4.1, including max. analog torque command (parameter
P1-41) and smoothing strategy of torque control mode. The current control block
diagram is used to manage the gain parameters of the servo drive and calculate the
current input provided to motor instantaneously. As the current control block diagram is
too complicated, setting the parameters of current control block diagram is not allowed.
The function and structure of torque command processing is shown as the figure
below:
The command source is selected according to the state of TCM0, TCM1 and
parameter P1-01 (T or Tz). Whenever the command signal needs to be more smoothly,
we recommend the users to use proportional gain (scalar) and low-pass filter to adjust
torque.
6-36
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
6.4.3 Smoothing Strategy of Torque Control Mode
Relevant parameters:
P1-07
TFLT
Smooth Constant of Analog Torque
Command (Low-pass Filter)
Operation
Keypad/Software
Interface:
Communication
Address: 010EH
010FH
Related Section:
Section 6.4.3
Default: 0
Control
T
Mode:
Unit: ms
Range: 0 ~ 1000 (0: Disabled)
Data Size: 16-bit
Display
Decimal
Format:
Settings: 0: Disabled
NOTE
1) If the setting value of parameter P1-07 is set to 0, it indicates the function of this
parameter is disabled and the command is just By-Pass.
Target Speed
TFLT
Revision September 2013
6-37
Chapter 6 Control Modes of Operation
ASDA-B2
6.4.4 Analog Torque Input Scaling
The analog voltage between T_REF and GND controls the motor torque command.
Using with parameter P1-41 can adjust the torque control ramp and its range.
300%
The torque control ramp is
determined by parameter P1-41
100%
Torque command
-10
-5
5
10
Analog Input Voltage (V)
-100%
-300%
Relevant parameters:
P1-41▲
TCM
Max. Analog Torque Command or Limit
Operation
Keypad/Software
Interface:
Communication
Address: 0152H
0153H
Related Section:
Section 6.4.4
Default: 100
Control
ALL
Mode:
Unit: %
Range: 0 ~ 1000
Data Size: 16-bit
Display
Decimal
Format:
Settings:
In Torque mode, this parameter is used to set the maximum analog torque
command based on the maximum input voltage (10V).
In PT and Speed mode, this parameter is used to set the maximum analog torque
limit based on the maximum input voltage (10V).
For example, in torque mode, if P1-41 is set to 100 and the input voltage is 10V, it
indicates that the torque command is 100% rated torque. If P1-41 is set to 100, but
the input voltage is changed to 5V, then the torque command is changed to 50%
rated torque.
Torque Command / Limit = Input Voltage Value x Setting value of P1-41 / 10
6-38
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
6.4.5 Timing Chart of Torque Control Mode
T4 (P1-14)
Internal speed
command
T3 (P1-13)
T2 (P1-12)
External analog
voltage or zero (0)
External I/O signal
T1
TCM0
OFF
TCM1
OFF
SON
ON
OFF
ON
ON
ON
NOTE
1) OFF indicates normally open and ON indicates normally closed.
2) When torque control mode is Tz, the torque command T1=0; when torque control mode is
T, the speed command T1 is external analog voltage input (Please refer to P1-01).
3) After Servo ON, the users can select command according to the state of TCM0~1.
Revision September 2013
6-39
Chapter 6 Control Modes of Operation
ASDA-B2
6.5 Control Modes Selection
Except signal control mode operation, ASDA-B2 series AC drive also provide PT-S, S-T,
PT-T, these three multiple modes for the users to select.
1) Speed / Position mode selection: PT-S
2) Speed / Torque mode selection: S-T
3) Torque / Position mode selection: PT-T
Mode
Dual Mode
Name
Code
Description
PT-S
06
Either PT or S control mode can be selected via the Digital
Inputs (DI)
PT-T
07
Either PT or T control mode can be selected via the Digital
Inputs (DI)
S-T
0A
Either S or T control mode can be selected via the Digital Inputs
(DI)
Sz and Tz mode selection is not provided. In order to avoid using too much DI inputs, we
recommend that the users can use external analog signal as input command in speed and
torque mode to reduce the use of DI inputs (SPD0~1 or TCM0~1).
Please refer to table 3.B and table 3.C in section 3.3.2 to see the default pin number of
DI/DO signal.
6.5.1 Speed / Position Control Mode Selection
PT-S Mode:
The command source of PT-S mode is from external input pulse. The speed command
can be the external analog voltage or internal parameters (P1-09 to P1-11). The speed
and position mode switching is controlled by the S-P signal. The timing chart of speed /
position control mode selection is shown as the figure below:
6-40
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
6.5.2 Speed / Torque Control Mode Selection
S-T Mode:
The speed command can be the external analog voltage or internal parameters (P1-09
to P1-11) and SPD0~1 is used to select speed command. The same as speed
command, the torque command can be the external analog voltage or internal
parameters (P1-12 to P1-14) and TCM0~1 is used to select torque command. The
speed and torque mode switching is controlled by the S-T signal.
The timing chart of speed / torque control mode selection is shown as the figure below:
In torque mode (when S-T is ON), torque command is selected by TCM0~1. When
switching to the speed mode (when S-T is OFF), the speed command is selected by
SPD0~1, and then the motor will immediately rotate following the command. After S-T
is ON again, it will immediately return to torque mode.
6.5.3 Torque / Position Control Mode Selection
PT-T Mode:
The command source of PT-T mode is from external input pulse. The torque command
can be the external input pulse or internal parameters (P1-12 to P1-14). The torque
and position mode switching is controlled by T-P signal.
The timing chart of speed / position control mode selection is shown as the figure
below:
\
Revision September 2013
6-41
Chapter 6 Control Modes of Operation
ASDA-B2
6.6 Others
6.6.1 Speed Limit
The max. servo motor speed can be limited by using parameter P1-55 no matter in
position, speed or torque control mode.
The command source of speed limit command is the same as speed command. It can
be the external analog voltage but also can be internal parameters (P1-09 to P1-11).
For more information of speed command source, please refer to chapter 6.3.1.
The speed limit only can be used in torque mode (T mode) to limit the servo motor
speed. When the torque command is the external analog voltage, there should be
surplus DI signal that can be treated as SPD0~1 and be used to select speed limit
command (internal parameter). If there is not enough DI signal, the external voltage
input can be used as speed limit command. When the Disable / Enable Speed Limit
Function Settings in parameter P1-02 is set to 1, the speed limit function is activated.
The timing chart of speed limit is shown as the figure below:
Disable / Enable Speed Limit Function
Settings in parameter P1-02 is set to 0
SPD0~1 INVALID
Disable / Enable Speed Limit Function
Settings in parameter P1-02 is set to 1
SPD0~1 VALID
Command Source Selection of Speed Limit
6.6.2 Torque Limit
The command source of torque limit command is the same as torque command. It can
be the external analog voltage but also can be internal parameters (P1-12 to P1-14).
For more information of torque command source, please refer to chapter 6.4.1.
The torque limit only can be used in position mode (PT mode) and speed mode (S
mode) to limit the output torque of servo motor. When the position command is the
external pulse and speed command is the external analog voltage, there should be
surplus DI signal that can be treated as TCM0~1 used to select torque limit command
(internal parameter). If there is not enough DI signal, the external voltage input can be
used as torque limit command. When the Disable / Enable Torque Limit Function
Settings in parameter P1-02 is set to 1, the torque limit function is activated.
The timing chart of torque limit is shown as the figure below:
Disable / Enable Torque Limit Function
Settings in parameter P1-02 is set to 0
TCM0~1 INVALID
Disable / Enable Torque Limit Function
Settings in parameter P1-02 is set to 1
TCM0~1 VALID
Command Source Selection of Torque Limit
6-42
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
6.6.3 Analog Monitor
User can use analog monitor to observe the required analog voltage signals. ASDA-B2
series provide two analog channels, they are PIN No. 1 and 3 of CN5 connector. The
parameters relative to analog monitor are shown below.
Relevant parameters:
P0-03
MON
Address: 0006H
0007H
Analog Monitor Output
Operation
Keypad/Software
Interface:
Related Section:
Section 6.6.3
Communication
Default: 00
Control
ALL
Mode:
Unit: Range: 00 ~ 77
Data Size: 16-bit
Display
Hexadecimal
Format:
Settings:
This parameter determines the functions of the analog monitor outputs.
MON1, MON2 Settings:
0: Motor speed (+/-8V / maximum motor speed)
1: Motor torque (+/-8V / maximum torque)
2: Pulse command frequency (+8Volts / 4.5Mpps)
3: Speed command (+/-8Volts / maximum speed command)
4: Torque command (+/-8Volts / maximum torque command)
5: V_BUS voltage (+/-8Volts / 450V)
6: Reserved
7: Reserved
Please note: For the setting of analog output voltage proportion, refer to the P1-04
and P1-05.
Example: P0-03 = 01 (MON1 is motor speed analog output, MON2 is motor torque
analog output)
Motor speed
MON1 output voltage= 8 ×
(Max. motor speed ×
P1-04
100
Revision September 2013
(unit: Volts)
)
6-43
Chapter 6 Control Modes of Operation
ASDA-B2
Motor toque
MON2 output voltage= 8 ×
(Max. motor torque ×
(unit: Volts)
P1-05
)
100
P1-03
Address: 0106H
0107H
AOUT Pulse Output Polarity Setting
Operation
Keypad/Software
Interface:
Communication
Related Section:
Section 3.3.3
Default: 0
Control
ALL
Mode:
Unit: Range: 0 ~ 13
Data Size: 16-bit
Display
Hexadecimal
Format:
Settings:
A: Analog monitor outputs polarity
0: MON1(+), MON2(+)
1: MON1(+), MON2(-)
2: MON1(-), MON2(+)
3: MON1(-), MON2(-)
P1-04
B: Position pulse outputs polarity
0: Forward output
1: Reverse output
MON1 Analog Monitor Output Proportion 1 (MON1)
Operation
Keypad/Software
Interface:
Communication
Address: 0108H
0109H
Related Section:
Section 6.4.4
Default: 100
Control
ALL
Mode:
Unit: % (full scale)
Range: 0 ~ 100
Data Size: 16-bit
Display
Decimal
Format:
6-44
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
Settings:
Please note:
For the setting of analog output voltage proportion, refer to the P1-03.
Example: P0-03 = 01 (MON1 is motor speed analog output, MON2 is motor torque
analog output)
Motor speed
MON1 output voltage= 8 ×
(Max. motor speed ×
P1-04
100
(unit: Volts)
)
Motor toque
MON2 output voltage= 8 ×
(Max. motor torque ×
P1-05
(unit: Volts)
)
100
P1-05
MON2 Analog Monitor Output Proportion 2 (MON2)
Operation
Keypad/Software
Interface:
Communication
Address: 010AH
010BH
Related Section:
Section 6.4.4
Default: 100
Control
ALL
Mode:
Unit: % (full scale)
Range: 0 ~ 100
Data Size: 16-bit
Display
Decimal
Format:
Settings:
Please note:
For the setting of analog output voltage proportion, refer to the P1-03.
Example: P0-03 = 01 (MON1 is motor speed analog output, MON2 is motor torque
analog output)
Motor speed
MON1 output voltage= 8 ×
(Max. motor speed ×
P1-04
100
(unit: Volts)
)
Motor toque
MON2 output voltage= 8 ×
(unit: Volts)
P1-05
(Max. motor torque ×
)
100
Revision September 2013
6-45
Chapter 6 Control Modes of Operation
P4-20
ASDA-B2
Analog Monitor Output Drift Adjustment
(MON1)
DOF1
Operation
Keypad / Software
Interface:
Communication
Address: 0428H
0429H
Related Section:
Section 6.4.4
Default: Factory setting
Control
ALL
Mode:
Unit: mV
Range: -800 ~ 800
Data Size: 16-bit
Display
Decimal
Format:
Settings:
Please note that when P2-08 is set to 10, the users cannot reset this parameter.
P4-21
Analog Monitor Output Drift Adjustment
(MON2)
DOF2
Operation
Keypad / Software
Interface:
Communication
Address: 042AH
042BH
Related Section:
Section 6.4.4
Default: 0
Control
ALL
Mode:
Unit: mV
Range: -800 ~ 800
Data Size: 16-bit
Display
Decimal
Format:
Settings:
Please note that when P2-08 is set to 10, the users cannot reset this parameter.
For example, when the users want to observe the analog voltage signal of channel 1, if
the monitor output setting range is 8V per 325Kpps, then it is needed to change the
setting value of parameter P1-04 (Analog Monitor Output Proportion 1) to 50
(=325Kpps/Max. input frequency). Other related parameters setting include parameter
P0-03 (A=3) and P1-03 (A=0~3, output polarity setting). In general, when output
voltage value of Ch1 is V1, the pulse command frequency is equal to (Max. input
frequency × V1/8) × P1-04/100.
Because there is an offset value of analog monitor output voltage, the zero voltage
level of analog monitor output does not match to the zero point of setting value. We
recommend the users can use Analog Monitor Output Drift Adjustment, DOF1
(parameter P4-20) and DOF2 (parameter P4-21) to improve this condition. The
maximum output voltage range of analog monitor output is ±8V. If the output voltage
6-46
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
exceed its limit, it is still limited within the range of ±8V. The revolution provided by
ASDA-B2 series is 10bit, approximated to 13mv/LSB.
8V
DOF
-8V
6.6.4 Electromagnetic Brake
When the servo drive is operating, if the digital output BRKR is set to Off, it indicates
the electromagnetic brake is disabled and motor is stop running and locked. If the
digital output BRKR is set to ON, it indicates electromagnetic brake is enabled and
motor can run freely.
There are two parameters that affect the electromagnetic brake. One is parameter P142 (MBT1) and the other is parameter P1-43 (MBT2). The users can use these two
parameters to set the On and Off delay time of electromagnetic brake. The
electromagnetic brake is usually used in perpendicular axis (Z-axis) direction to reduce
the large energy generated from servo motor. Using electromagnetic brake can avoid
the load may slip since there is no motor holding torque when power is off. Without
using electromagnetic brake may reduce the life of servo motor. To avoid malfunction,
the electromagnetic brake should be activated after servo system is off (Servo Off).
If the users desire to control electromagnetic brake via external controller, not by the
servo drive, the users must execute the function of electromagnetic brake during the
period of time when servo motor is braking. The braking strength of motor and
electromagnetic brake must be in the same direction when servo motor is braking.
Then, the servo drive will operate normally. However, the servo drive may generate
larger current during acceleration or at constant speed and it may the cause of
overload (servo fault).
Revision September 2013
6-47
Chapter 6 Control Modes of Operation
ASDA-B2
Timing chart for using servo motor with electromagnetic brake:
ON
SON
(DI Input)
OFF
OFF
ON
BRKR
(DO Output)
OFF
OFF
MBT1(P1-42)
MBT2(P1-43)
ZSPD(P1-38)
Motor Speed
BRKR output timing explanation:
1. When SERVO OFF (when DI SON is not activated), the BRKR output goes Off
(electromagnetic brake is locked) after the delay time set by P1-43 is reached
and the motor speed is still higher than the setting value of P1-38.
2. When SERVO OFF (when DI SON is not activated), the BRKR output goes Off
(electromagnetic brake is locked) if the delay time set by P1-43 is not reached
and the motor speed is still lower than the setting value of P1-38.
Electromagnetic Brake Wiring Diagram
NOTE
6-48
1)
Please refer to Chapter 3 Connections and Wiring for more wiring information.
2)
The BRKR signal is used to control the brake operation. The VDD DC24V power supply
of the servo drive can be used to power the relay coil (Relay). When BRKR signal is ON,
the motor brake will be activated.
3)
Please note that the coil of brake has no polarity.
4)
The power supply for brake is DC24V. Never use it for VDD, the +24V source voltage.
Revision September 2013
ASDA-B2
Chapter 6 Control Modes of Operation
The timing charts of control circuit power and main circuit power:
L1, L2
Control Circuit
Power
1 sec
5V
Control Circuit
Power
> 0msec
R, S, T
Main Circuit
Power
800ms
BUS Voltage
READY
2 sec
SERVO
READY
SERVO ON
(DI Input)
1 msec (min)+ Response Filter Time of Digital Input ( P2-09)
SERVO ON
(DO Output)
Position \ Speed \
Torque Command
Input
Revision September 2013
Input available
6-49
Chapter 6 Control Modes of Operation
ASDA-B2
This page is intentionally left blank.
6-50
Revision September 2013
Chapter 7
Servo Parameters
7.1 Definition
There are following five groups for drive parameters:
Group 0: Monitor parameters
(example: P0-xx)
Group 1: Basic parameters
(example: P1-xx)
Group 2: Extension parameters
(example: P2-xx)
Group 3: Communication parameters (example: P3-xx)
Group 4: Diagnosis parameters
(example: P4-xx)
Abbreviation of control modes:
PT: Position control mode (command from external signal)
S: Speed control mode
T: Torque control mode
Explanation of symbols (marked after parameter)
(★)
(▲)
()
()
Read-only register, such as P0-00, P0-01, P4-00.
Parameter cannot be set when Servo On (when the servo drive is enabled), such
as P1-00, P1-46 and P2-33.
Parameter is effective only after the servo drive is restarted (after switching power
off and on), such as P1-01 and P3-00.
Parameter setting values are not retained when power is off, such as P2-31 and
P3-06.
Revision September 2013
7-1
Chapter 7 Servo Parameters
ASDA-B2
7.2 Parameters Summary
Monitor and General Use
Parameter
Name
P0-00★
VER
Function
Firmware Version
Default
Unit
Factory
Setting
N/A
Control Mode
PT
S
T
Related
Section
O
O
O
-
P0-01
ALE
Drive Fault Code
N/A
N/A
O
O
O
11.1
11.2
11.3
P0-02
STS
Drive Status (Front Panel
Display)
00
N/A
O
O
O
7.2
P0-03
MON
Analog Monitor Output
01
N/A
O
O
O
4.3.5
P0-08★
TSON
Servo Startup Time
0
Hour
P0-09★
CM1
Status Monitor 1
N/A
N/A
O
O
O
4.3.5
P0-10★
CM2
Status Monitor 2
N/A
N/A
O
O
O
4.3.5
P0-11★
CM3
Status Monitor 3
N/A
N/A
O
O
O
4.3.5
P0-12★
CM4
Status Monitor 4
N/A
N/A
O
O
O
4.3.5
P0-13★
CM5
Status Monitor 5
N/A
N/A
O
O
O
4.3.5
P0-17
CM1A
Status Monitor Selection 1
0
N/A
-
P0-18
CM2A
Status Monitor Selection 2
0
N/A
-
P0-19
CM3A
Status Monitor Selection 3
0
N/A
-
P0-20
CM4A
Status Monitor Selection 4
0
N/A
-
P0-21
CM5A
Status Monitor Selection 5
0
N/A
-
0
N/A
P0-46★
SVSTS Servo Output Status Display
P1-04
MON1
P1-05
MON2
Analog Monitor Output
Proportion 1 (MON1)
Analog Monitor Output
Proportion 2 (MON2)
100
100
%(full
scale)
%(full
scale)
-
O
O
O
-
O
O
O
6.4.4
O
O
O
6.4.4
Explanation of symbols (marked after parameter)
(★)
(▲)
()
()
Read-only register.
Parameter cannot be set when Servo On (when the servo drive is enabled).
Parameter is effective only after the servo drive is restarted (after switching power off and
on).
Parameter setting values are not retained when power is off.
7-2
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Smooth Filter and Resonance Suppression
Parameter
Name
P1-06
SFLT
P1-07
TFLT
P1-08
PFLT
P1-34
TACC
P1-35
TDEC
P1-36
TSL
P1-59
MFLT
P1-62
FRCL
P1-63
FRCT
P1-68
PFLT2
P2-23
NCF1
P2-24
DPH1
P2-43
NCF2
P2-44
DPH2
P2-45
NCF3
P2-46
DPH3
P2-47
ANCF
P2-48
ANCL
P2-25
NLP
P2-49
SJIT
Function
Control Mode
Related
Section
Default
Unit
0
ms
0
ms
0
10ms
Acceleration Time
200
ms
O
6.3.3
Deceleration Time
200
ms
O
6.3.3
0
ms
O
6.3.3
0
0.1ms
O
-
0
%
O
O
O
-
0
ms
O
O
O
-
0
ms
O
1000
Hz
O
O
O
6.3.7
0
dB
O
O
O
6.3.7
1000
Hz
O
O
O
6.3.7
0
dB
O
O
O
6.3.7
1000
Hz
O
O
O
6.3.7
0
dB
O
O
O
6.3.7
1
N/A
O
O
O
-
100
N/A
O
O
O
-
2 or 5
0.1ms
O
O
O
6.3.7
0
sec
O
O
O
-
Accel/Decel Smooth Constant
of Analog Speed Command
(Low-pass Filter)
Smooth Constant of Analog
Torque Command (Low-pass
Filter)
Smooth Constant of Position
Command (Low-pass Filter)
Accel/Decel S-curve
Analog Speed Linear Filter
(Moving Filter)
Friction Compensation
Percentage
Friction Compensation Smooth
Constant
Position Command Moving
Filter
Notch Filter 1 (Resonance
Suppression)
Notch Filter Attenuation Rate 1
(Resonance Suppression)
Notch Filter 2 (Resonance
Suppression)
Notch Filter Attenuation Rate 2
(Resonance Suppression)
Notch Filter 3 (Resonance
Suppression)
Notch Filter Attenuation Rate 3
(Resonance Suppression)
Auto Resonance Suppression
Mode Selection
Auto Resonance Suppression
Detection Level
Low-pass Filter Time Constant
(Resonance Suppression)
Speed Detection Filter and Jitter
Suppression
PT
S
T
O
6.3.3
O
O
6.4.3
6.2.4
-
Explanation of symbols (marked after parameter)
(★)
(▲)
()
()
Read-only register.
Parameter cannot be set when Servo On (when the servo drive is enabled).
Parameter is effective only after the servo drive is restarted (after switching power off and
on).
Parameter setting values are not retained when power is off.
Revision September 2013
7-3
Chapter 7 Servo Parameters
ASDA-B2
Gain and Switch
Control Mode
Related
Section
Parameter
Name
Function
Default
Unit
P2-00
KPP
Proportional Position Loop Gain
35
rad/s
O
6.2.5
P2-01
PPR
Position Loop Gain Switching
Rate
100
%
O
6.2.5
P2-02
PFG
Position Feed Forward Gain
50
%
O
6.2.5
P2-03
PFF
Smooth Constant of Position
Feed Forward Gain
5
ms
O
-
P2-04
KVP
Proportional Speed Loop Gain
500
rad/s
O
O
O
6.3.6
P2-05
SPR
Speed Loop Gain Switching
Rate
100
%
O
O
O
-
P2-06
KVI
Speed Integral Compensation
100
rad/s
O
O
O
6.3.6
P2-07
KVF
Speed Feed Forward Gain
0
%
O
O
O
6.3.6
P2-26
DST
External Anti-interference Gain
0
0.001
O
O
O
-
P2-27
GCC
Gain Switching Control
Selection
0
N/A
O
O
O
-
P2-28
GUT
Gain Switching Time Constant
10
10ms
O
O
O
-
P2-29
GPE
Gain Switching Condition
pulse
1280000 Kpps
r/min
O
O
O
-
P2-31
AUT1
Speed Frequency Response
Level in Auto and Semi-Auto
Mode
80
Hz
O
O
O
P2-32▲
AUT2
Tuning Mode Selection
0
N/A
O
O
O
PT
S
T
5.6
6.3.6
5.6
6.3.6
Explanation of symbols (marked after parameter)
(★)
(▲)
()
()
Read-only register.
Parameter cannot be set when Servo On (when the servo drive is enabled).
Parameter is effective only after the servo drive is restarted (after switching power off and
on).
Parameter setting values are not retained when power is off.
Position Control
Parameter
Name
P1-01
CTL
P1-02▲
PSTL
7-4
Function
Control Mode
PT
S
T
Related
Section
pulse
r/min
N-M
O
O
O
6.1
N/A
O
O
O
6.6
Default
Unit
Control Mode and Output
Direction
0
Speed and Torque Limit
0
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Position Control
Parameter
P1-12 ~
P1-14
Name
Function
PT
S
T
%
O
O
O
6.4.1
2500
pulse
O
O
O
-
rated
r/min
O
O
O
-
0
N/A
O
-
Unit
100
Encoder Output Pulse Number
TQ1 ~ 3 1st ~ 3rd Torque Limit
P1-46▲
GR3
P1-55
MSPD
Maximum Speed Limit
P2-50
DCLR
Pulse Deviation Clear Mode
Control Mode
Related
Section
Default
External Pulse Control Command (PT mode)
P1-00▲
PTT
P1-44▲
GR1
P1-45▲
GR2
P2-60▲
GR4
P2-61▲
GR5
P2-62▲
GR6
External Pulse Input Type
st
Electronic Gear Ratio (1
Numerator) (N1)
Electronic Gear Ratio
(Denominator) (M)
Electronic Gear Ratio (2nd
Numerator) (N2)
Electronic Gear Ratio (3rd
Numerator) (N3)
Electronic Gear Ratio (4th
Numerator) (N4)
0x2
N/A
O
6.2.1
1
pulse
O
6.2.3
1
pulse
O
6.2.3
1
pulse
O
-
1
pulse
O
-
1
pulse
O
-
Explanation of symbols (marked after parameter)
(★)
(▲)
()
()
Read-only register.
Parameter cannot be set when Servo On (when the servo drive is enabled).
Parameter is effective only after the servo drive is restarted (after switching power off and
on).
Parameter setting values are not retained when power is off.
Speed Control
Parameter
Name
P1-01
CTL
P1-02▲
Function
PT
S
T
pulse
r/min
N-M
O
O
O
6.1
0
N/A
O
O
O
6.6
1
pulse
O
O
O
-
rated
r/min
O
O
O
-
0.1
r/min
O
O
6.3.1
%
O
O
6.6.2
Unit
Control Mode and Output
Direction
0
PSTL
Speed and Torque Limit
P1-46▲
GR3
Encoder Output Pulse Number
P1-55
MSPD
Maximum Speed Limit
P1-09 ~
P1-11
SP1 ~ 3 1st ~ 3rd Speed Command
1000
~
3000
P1-12 ~
P1-14
TQ1 ~ 3 1st ~ 3rd Torque Limit
100
Revision September 2013
Control Mode
Related
Section
Default
O
7-5
Chapter 7 Servo Parameters
P1-40▲
P1-41▲
P1-76
ASDA-B2
Max. Analog Speed Command
or Limit
Max. Analog Torque Command
TCM
or Limit
Max. Rotation Speed of Encoder
AMSPD
Output
VCM
rated
r/min
100
%
5500
r/min
O
O
6.3.4
O
O
O
-
O
O
O
-
Explanation of symbols (marked after parameter)
(★)
(▲)
()
()
Read-only register.
Parameter cannot be set when Servo On (when the servo drive is enabled).
Parameter is effective only after the servo drive is restarted (after switching power off and
on).
Parameter setting values are not retained when power is off.
Torque Control
PT
S
T
pulse
r/min
N-M
O
O
O
6.1
0
N/A
O
O
O
6.6
1
pulse
O
O
O
-
rated
r/min
O
O
O
-
SP1~3 1st ~ 3rd Speed Limit
1000
~
3000
r/min
O
O
6.6.1
TQ1~3 1st ~ 3rd Torque Command
100
%
O
O
6.4.1
rated
r/min
O
O
-
100
%
O
O
6.4.4
Name
Default
Unit
P1-01
CTL
Control Mode and Output
Direction
0
P1-02▲
PSTL
Speed and Torque Limit
P1-46▲
GR3
Encoder Output Pulse Number
P1-55
MSPD
P1-09
~
P1-11
P1-12
~
P1-14
Control Mode
Related
Section
Parameter
P1-40▲
VCM
P1-41▲
TCM
Function
Maximum Speed Limit
Max. Analog Speed Command
or Limit
Max. Analog Torque Command
or LImit
O
O
Explanation of symbols (marked after parameter)
(★)
(▲)
()
()
7-6
Read-only register.
Parameter cannot be set when Servo On (when the servo drive is enabled).
Parameter is effective only after the servo drive is restarted (after switching power off and
on).
Parameter setting values are not retained when power is off.
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Digital I/O and Relative Input Output Setting
Parameter
Name
Function
P2-09
DRT
Bounce Filter
P2-10
DI1
P2-11
Control Mode Related
PT
S
T Section
Default
Unit
2
2ms
O
O
O
-
Digital Input Terminal 1 (DI1)
101
N/A
O
O
O
Table 7.A
DI2
Digital Input Terminal 2 (DI2)
104
N/A
O
O
O
Table 7.A
P2-12
DI3
Digital Input Terminal 3 (DI3)
116
N/A
O
O
O
Table 7.A
P2-13
DI4
Digital Input Terminal 4 (DI4)
117
N/A
O
O
O
Table 7.A
P2-14
DI5
Digital Input Terminal 5 (DI5)
102
N/A
O
O
O
Table 7.A
P2-15
DI6
Digital Input Terminal 6 (DI6)
22
N/A
O
O
O
Table 7.A
P2-16
DI7
Digital Input Terminal 7 (DI7)
23
N/A
O
O
O
Table 7.A
P2-17
DI8
Digital Input Terminal 8 (DI8)
21
N/A
O
O
O
Table 7.A
P2-36
DI9
External Digital Input Terminal 9
(DI9)
0
N/A
O
O
O
Table 7.A
P2-18
DO1
Digital Output Terminal 1 (DO1)
101
N/A
O
O
O
Table 7.B
P2-19
DO2
Digital Output Terminal 2 (DO2)
103
N/A
O
O
O
Table 7.B
P2-20
DO3
Digital Output Terminal 3 (DO3)
109
N/A
O
O
O
Table 7.B
P2-21
DO4
Digital Output Terminal 4 (DO4)
105
N/A
O
O
O
Table 7.B
P2-22
DO5
Digital Output Terminal 5 (DO5)
7
N/A
O
O
O
Table 7.B
P2-37
DO6
Digital Output Terminal 6 (DO6)
7
N/A
O
O
O
Table 7.B
P1-38
ZSPD
Zero Speed Range Setting
100
0.1
r/min
O
O
O
Table 7.B
P1-39
SSPD
Target Motor Speed
3000
r/min
O
O
O
Table 7.B
P1-42
MBT1
0
ms
O
O
O
6.5.5
P1-43
MBT2
0
ms
O
O
O
6.5.5
P1-47
SCPD
10
r/min
P1-54
PER
Positioning Completed Width
12800
pulse
O
P1-56
OVW
Output Overload Warning Time
120
%
O
On Delay Time of
Electromagnetic Brake
Off Delay Time of
Electromagnetic Brake
Speed Reached Output Range
O
Table 7.B
Table 7.B
O
O
Table 7.B
Explanation of symbols (marked after parameter)
(★)
(▲)
()
()
Read-only register.
Parameter cannot be set when Servo On (when the servo drive is enabled).
Parameter is effective only after the servo drive is restarted (after switching power off and
on).
Parameter setting values are not retained when power is off.
Revision September 2013
7-7
Chapter 7 Servo Parameters
ASDA-B2
Communication
Control Mode
PT
S
T
Related
Section
N/A
O
O
O
8.2
0x0203
bps
O
O
O
8.2
Communication Protocol
6
N/A
O
O
O
8.2
Transmission Fault Treatment
0
N/A
O
O
O
8.2
0
sec
O
O
O
8.2
0
N/A
O
O
O
8.2
0
N/A
O
O
O
8.2
0
1ms
O
O
O
8.2
0000
N/A
O
O
O
8.2
Parameter
Name
Function
Default
Unit
P3-00
ADR
Communication Address Setting
0x7F
P3-01
BRT
Transmission Speed
P3-02
PTL
P3-03
FLT
P3-04
CWD
P3-05
CMM
P3-06
SDI
P3-07
CDT
P3-08
MNS
Communication Time Out
Detection
Communication Selection
Digital Input Communication
Function
Communication Response
Delay Time
Monitor Mode
Explanation of symbols (marked after parameter)
(★)
(▲)
()
()
Read-only register.
Parameter cannot be set when Servo On (when the servo drive is enabled).
Parameter is effective only after the servo drive is restarted (after switching power off and
on).
Parameter setting values are not retained when power is off.
Diagnosis
Parameter
Name
P4-00★
ASH1
P4-01★
Control Mode Related
PT
S
T Section
Default
Unit
Fault Record (N)
0
N/A
O
O
O
4.4.1
ASH2
Fault Record (N-1)
0
N/A
O
O
O
4.4.1
P4-02★
ASH3
Fault Record (N-2)
0
N/A
O
O
O
4.4.1
P4-03★
ASH4
Fault Record (N-3)
0
N/A
O
O
O
4.4.1
P4-04★
ASH5
Fault Record (N-4)
0
N/A
O
O
O
4.4.1
P4-05
JOG
JOG Operation
20
r/min
O
O
O
4.4.2
P4-06▲
FOT
Force Output Contact Control
0
N/A
O
O
O
4.4.4
P4-07
ITST
Input Status
0
N/A
O
O
O
4.4.5
8.2
P4-08★
PKEY
Digital Keypad Input of Servo
Drive
N/A
N/A
O
O
O
-
7-8
Function
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Diagnosis
Parameter
Name
Function
P4-09★
MOT
Output Status
P4-10▲
CEN
Adjustment Function
P4-11
SOF1
P4-12
SOF2
P4-14
TOF2
P4-15
COF1
P4-16
COF2
P4-17
COF3
P4-18
COF4
P4-19
TIGB
P4-20
DOF1
P4-21
DOF2
P4-22
SAO
P4-23
TAO
Control Mode Related
PT
S
T Section
Default
Unit
N/A
N/A
O
O
O
4.4.6
0
N/A
O
O
O
-
N/A
O
O
O
-
N/A
O
O
O
-
N/A
O
O
O
-
N/A
O
O
O
-
N/A
O
O
O
-
N/A
O
O
O
-
N/A
O
O
O
-
N/A
O
O
O
-
0
mV
O
O
O
6.4.4
0
mV
O
O
O
6.4.4
Analog Speed Input Offset
0
mV
Analog Torque Input Offset
0
mV
Analog Speed Input Drift
Adjustment 1
Analog Speed Input Drift
Adjustment 2
Analog Torque Drift Adjustment
2
Current Detector Drift
Adjustment (V1 phase)
Current Detector Drift
Adjustment (V2 phase)
Current Detector Drift
Adjustment (W1 phase)
Current Detector Drift
Adjustment (W2 phase)
IGBT NTC Calibration
Analog Monitor Output Drift
Adjustment (MON1)
Analog Monitor Output Drift
Adjustment (MON2)
Factory
Setting
Factory
Setting
Factory
Setting
Factory
Setting
Factory
Setting
Factory
Setting
Factory
Setting
Factory
Setting
O
O
-
Explanation of symbols (marked after parameter)
(★)
(▲)
()
()
Read-only register.
Parameter cannot be set when Servo On (when the servo drive is enabled).
Parameter is effective only after the servo drive is restarted (after switching power off and
on).
Parameter setting values are not retained when power is off.
Revision September 2013
7-9
Chapter 7 Servo Parameters
ASDA-B2
7.3 Detailed Parameter Listings
Group 0: P0-xx
P0-00★
Monitor Parameters
VER
Firmware Version
Operation
Keypad/Software
Interface:
Default: Factory setting
Control
ALL
Mode:
Unit: Range: Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0000H
0001H
Related Section: N/A
Settings:
This parameter displays the firmware version of the servo drive.
P0-01■
ALE
Drive Fault Code
Operation
Keypad/Software
Communication
Interface:
Default: Control
ALL
Mode:
Unit: Range: 0 ~ 0 (0: clear the fault or restart the servo
drive, the same function of ARST (DI signal))
Data Size: 16-bit
Display
BCD
Format:
Address: 0002H
0003H
Related Section:
Section: 11.1
Section: 11.2
Section: 11.3
Settings:
This parameter shows the current servo drive fault if the servo drive is currently
faulted.
The fault code is hexadecimal data but displayed in BCD format (Binary coded
decimal).
Servo Drive Fault Codes:
001: Overcurrent
002: Overvoltage
003: Undervoltage (This fault code shows when main circuit voltage is below its
minimum specified value while Servo On, and it will not show while Servo Off.
This fault code can’t be cleared automatically after the voltage has returned
within its specification. Please refer to parameter P2-66.)
004: Motor error (The drive and motor are not correctly matched for size (power
rating).
005: Regeneration error
006: Overload
7-10
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
007: Overspeed
008: Abnormal pulse control command
009: Excessive deviation
010: Reserved
011: Encoder error (The wiring of the encoder is in error and this causes the
communication error between the servo drive and the encoder.)
012: Adjustment error
013: Emergency stop activated
014: Reverse limit switch error
015: Forward limit switch error
016: IGBT temperature error
017: Memory error
018: Encoder output error
019: Serial communication error
020: Serial communication time out
021: Reserved
022: Input power phase loss
023: Pre-overload warning
024: Encoder initial magnetic field error
025: Encoder internal error
026: Encoder data error
027: Motor internal error
028: Motor internal error
029: Motor internal error
030: Motor protection error
030: Motor protection error
031: U,V,W, GND wiring error
035: Motor temperature error
048: Excessive encoder output error
067: Motor temperature warning
099: DSP firmware upgrade
P0-02
STS
Drive Status (Front Panel Display)
Operation
Keypad/Software
Interface:
Default: 00
Control
ALL
Mode:
Unit: Range: 0 ~ 18
Data Size: 16-bit
Display
Decimal
Format:
Revision September 2013
Communication
Address: 0004H
0005H
Related Section:
Section 7.2
7-11
Chapter 7 Servo Parameters
ASDA-B2
Settings:
This parameter shows the servo drive status.
00: Motor feedback pulse number (after electronic gear ratio is set) [user unit]
01: Input pulse number of pulse command (after electronic gear ratio is set) [user unit]
02: Position error counts between control command pulse and feedback pulse [user
unit]
03: Motor feedback pulse number (encoder unit, 160000 pulse/rev) [pulse]
04: Input pulse number of pulse command (before electronic gear ratio is set) [pulse]
05: Position error counts [pulse]
06: Input frequency of pulse command [Kpps]
07: Motor rotation speed [r/min]
08: Speed input command [Volt]
09: Speed input command [r/min]
10: Torque input command [Volt]
11: Torque input command [%]
12: Average load [%]
13: Peak load [%]
14: Main circuit voltage [Volt]
15: Ratio of load inertia to Motor inertia [0.1times]
16: IGBT temperature
17: Resonance frequency [Hz]
18: Absolute pulse number relative to encoder (use Z phase as home). The value of Z
phase home point is 0, and it can be the value from -5000 to +5000 pulses.
0
0
0
Z
Z
Z
+5000 -4999 +5000 -4999
The interval of two Z phase pulse command is 10000 pulse.
112: Observe the communication quality of encoder
7-12
Revision September 2013
ASDA-B2
P0-03
Chapter 7 Servo Parameters
MON
Address: 0006H
0007H
Related Section:
Section 6.6.3
Analog Monitor Output
Operation
Keypad/Software
Interface:
Default: 00
Control
ALL
Mode:
Unit: Range: 00 ~ 77
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Settings:
This parameter determines the functions of the analog monitor outputs.
MON1, MON2 Settings:
0: Motor speed (+/-8V / maximum motor speed)
1: Motor torque (+/-8V / maximum torque)
2: Pulse command frequency (+8Volts / 4.5Mpps)
3: Speed command (+/-8Volts / maximum speed command)
4: Torque command (+/-8Volts / maximum torque command)
5: V_BUS voltage (+/-8Volts / 450V)
6: Reserved
7: Reserved
Communication error
Continuous communication error
7-9 times
Continuous communication error
5-6 times
Continuous communication error
3-4 times
Continuous communication error
under 2 times
Please note:
For the setting
of analog
output voltage
proportion,
refer to the
P1-04 and
P1-05.
Communication quality
3(servere)
2 (bad)
1(moderate)
0 (good)
Example:
P0-03 = 01 (MON1 is motor speed analog output, MON2 is motor torque analog
output)
Motor speed
MON1 output voltage= 8 ×
(Max. motor speed ×
Revision September 2013
P1-04
100
(unit: Volts)
)
7-13
Chapter 7 Servo Parameters
ASDA-B2
Motor toque
MON2 output voltage= 8 ×
(Max. motor torque ×
P1-05
100
(unit: Volts)
)
P0-04■
Reserved (Do Not Use)
Address: 0008H
0009H
P0-05■
Reserved (Do Not Use)
Address: 000AH
000BH
P0-06■
Reserved (Do Not Use)
Address: 000CH
000DH
P0-07■
Reserved (Do Not Use)
Address: 000EH
000FH
P0-08★
TSON Servo Startup Time
Operation
Keypad/Software
Communication
Interface:
Default: 0
Control
Mode:
Unit: Hour
Range: High Word: 0 ~ 65535
Low Word: 0 ~ 65535
Data Size: 16-bit
Display
Decimal
Format:
Address: 0010H
0011H
Related Section: N/A
Settings:
High Word: Servo enable time
Low Word: Servo power on time
P0-09★
CM1
Status Monitor 1
Operation
Keypad/Software
Interface:
Default: Control
ALL
Mode:
Unit: Range: Data Size: 32-bit
Display
Decimal
Format:
Communication
Address: 0012H
0013H
Related Section:
Section 4.3.5
Settings:
This parameter is used to provide the value of one of the status monitoring functions
found in P0-02. The value of P0-09 is determined by P0-17 (desired drive status)
through communication setting or the keypad. The drive status can be read from the
communication address of this parameter via communication port.
7-14
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
For example:
Set P0-17 to 3, then all consequent reads of P0-09 will return the motor feedback
pulse number in pulse.
When reading the drive status through Modbus communication, the system should
read two 16-bit data stored in the addresses of 0012H and 0013H to form a 32-bit
data.
(0013H : 0012H) = (High Word : Low Word)
When reading the drive ststus through the keypad, if P0-02 is set to 23, VAR-1 will
quickly show for about two seconds and then the value of P0-09 will display on the
display.
P0-10★
CM2
Status Monitor 2
Operation
Keypad/Software
Interface:
Default: Control
ALL
Mode:
Unit: Range: Data Size: 32-bit
Display
Decimal
Format:
Communication
Address: 0014H
0015H
Related Section:
Section 4.3.5
Settings:
This parameter is used to provide the value of one of the status monitoring functions
found in P0-02. The value of P0-10 is determined by P0-18 (desired drive status)
through communication setting or the keypad. The drive status can be read from the
communication address of this parameter via communication port.
When reading the drive status through the keypad, if P0-02 is set to 24, VAR-2 will
quickly show for about two seconds and then the value of P0-10 will display on the
display.
P0-11★
CM3
Status Monitor 3
Operation
Keypad/Software
Interface:
Default: Control
ALL
Mode:
Unit: Range: Data Size: 32-bit
Display
Decimal
Format:
Communication
Address: 0016H
0017H
Related Section:
Section 4.3.5
Settings:
This parameter is used to provide the value of one of the status monitoring functions
found in P0-02. The value of P0-11 is determined by P0-19 (desired drive status)
through communication setting or the keypad. The drive status can be read from the
Revision September 2013
7-15
Chapter 7 Servo Parameters
ASDA-B2
communication address of this parameter via communication port.
When reading the drive status through the keypad, if P0-02 is set to 25, VAR-3 will
quickly show for about two seconds and then the value of P0-11 will display on the
display.
P0-12★
CM4
Status Monitor 4
Operation
Keypad/Software
Interface:
Default: Control
ALL
Mode:
Unit: Range: Data Size: 32-bit
Display
Decimal
Format:
Communication
Address: 0018H
0019H
Related Section:
Section 4.3.5
Settings:
This parameter is used to provide the value of one of the status monitoring functions
found in P0-02. The value of P0-12 is determined by P0-20 (desired drive status)
through communication setting or the keypad. The drive status can be read from the
communication address of this parameter via communication port.
When reading the drive status through the keypad, if P0-02 is set to 26, VAR-4 will
quickly show for about two seconds and then the value of P0-12 will display on the
display.
P0-13★
CM5
Status Monitor 5
Operation
Keypad/Software
Interface:
Default: Control
ALL
Mode:
Unit: Range: Data Size: 32-bit
Display
Decimal
Format:
Communication
Address: 001AH
001BH
Related Section:
Section 4.3.5
Settings:
This parameter is used to provide the value of one of the status monitoring functions
found in P0-02. The value of P0-12 is determined by P0-20 (desired drive status)
through communication setting or the keypad. The drive status can be read from the
communication address of this parameter via communication port.
7-16
P0-14
Reserved (Do Not Use)
Address: 001CH
001DH
P0-15
Reserved (Do Not Use)
Address: 001EH
001FH
Revision September 2013
ASDA-B2
P0-16
P0-17
Chapter 7 Servo Parameters
Address: 0020H
0021H
Reserved (Do Not Use)
CM1A Status Monitor Selection 1
Operation
Keypad/Software
Interface:
Default: 0
Control
Mode:
Unit: Range: 0 ~ 18
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0022H
0023H
Related Section: N/A
Settings:
This parameter is used to determine the drive status found in P0-02. The selected
drive status will be displayed by P0-09.
For example:
Set P0-17 to 7, then all consequent reads of P0-09 will return the motor rotation speed
in r/min.
P0-18
CM2A Status Monitor Selection 2
Operation
Keypad/Software
Interface:
Default: 0
Control
Mode:
Unit: Range: 0 ~ 18
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0024H
0025H
Related Section: N/A
Settings:
This parameter is used to determine the drive status found in P0-02.
P0-19
CM3A Status Monitor Selection 3
Operation
Keypad/Software
Interface:
Default: 0
Control
Mode:
Unit: Range: 0 ~ 18
Data Size: 16-bit
Display
Decimal
Format:
Revision September 2013
Communication
Address: 0026H
0027H
Related Section: N/A
7-17
Chapter 7 Servo Parameters
ASDA-B2
Settings:
This parameter is used to determine the drive status found in P0-02.
P0-19
CM3A Status Monitor Selection 3
Operation
Keypad/Software
Interface:
Default: 0
Control
Mode:
Unit: Range: 0 ~ 18
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0026H
0027H
Related Section: N/A
Settings:
This parameter is used to determine the drive status found in P0-02.
P0-20
CM4A Status Monitor Selection 4
Operation
Keypad/Software
Interface:
Default: 0
Control
Mode:
Unit: Range: 0 ~ 18
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0028H
0029H
Related Section: N/A
Settings:
This parameter is used to determine the drive status found in P0-02.
P0-21
CM5A Status Monitor Selection 5
Operation
Keypad/Software
Interface:
Default: 0
Control
Mode:
Unit: Range: 0 ~ 18
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 002AH
002BH
Related Section: N/A
Settings:
This parameter is used to determine the drive status found in P0-02.
7-18
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
P0-22
Reserved (Do Not Use)
Address: 002CH
002DH
P0-23
Reserved (Do Not Use)
Address: 002EH
002FH
P0-24
Reserved (Do Not Use)
P0-44★
Address: 0030H
0031H
Address: 0058H
PCMN Status Monitor Register (PC Software Setting)
0059H
Operation
Related Section:
Keypad/Software
Communication
Interface:
Section 4.3.5
Default: 0x0
Control
ALL
Mode:
Unit: Range: determined by the communication address of
the designated parameter
Data Size: 32-bit
Display
Decimal
Format:
Settings:
The function of this parameter is the same as P0-09 (Please refer to P0-09). Please
note that this pamameter can be set through communication setting only.
P0-45■
PCMNA
Status Monitor Register Selection (PC
Software Setting)
Operation
Keypad/Software
Interface:
Default: 0x0
Control
ALL
Mode:
Unit: Range: 0~127
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 005AH
005BH
Related Section:
Section 4.3.5
Settings:
The function of this parameter is the same as P0-17 (Please refer to P0-17). Please
note that this pamameter can be set through communication setting only.
P0-46★
SVSTS Servo Output Status Display
Operation
Keypad/Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: Range: 0x00 ~ 0xFF
Data Size: 16-bit
Revision September 2013
Communication
Address: 005CH
005DH
Related Section: N/A
7-19
Chapter 7 Servo Parameters
ASDA-B2
Display
Hexadecimal
Format:
Settings:
This parameter is used to display the digital output signal of the servo drive. The servo
output status display will show in hexadecimal format.
Bit0: SRDY (Servo ready)
Bit1: SON (Servo On)
Bit2: ZSPD (At Zero speed)
Bit3: TSPD (At Speed reached)
Bit4: TPOS (At Positioning completed)
Bit5: TQL (At Torque limit)
Bit6: ALRM (Servo alarm activated)
Bit7: BRKR (Electromagnetic brake control)
Bit9: OLW (Output overload warning)
Bit10: WARN (Servo warning activated. WARN is activated when the drive has
detected reverse limit error; forward limit error, emergency stop, serial
communication error, and undervoltage these fault conditions.)
Bit11: Reserved
Bit12: Reserved
Bit13: Reserved
Bit14: Reserved
Bit15: Reserved
The servo output status display can be monitored through communication also.
7-20
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Group 1: P1-xx
P1-00▲
Basic Parameters
PTT
External Pulse Input Type
Operation
Keypad/Software
Interface:
Default: 0x2
Control
PT
Mode:
Unit: Range: 0 ~ 1142
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 0100H
0101H
Related Section:
Section 6.2.1
Settings:
A: Input pulse type
0: AB phase pulse (4x) (Quadrature Input)
1: Clockwise (CW) + Counterclockwise(CCW) pulse
2: Pulse + Direction
3: Other settings:
B: Input pulse filter
This setting is used to suppress or reduce the chatter caused by the noise, etc.
However, if the instant input pulse filter frequency is over high, the frequency that
exceeds the setting value will be regarded as noise and filtered.
Setting
Value
Revision September 2013
Low-speed Filter Frequency
(Min. Filter Frequency
1)
(see note
)
Setting
Value
High-speed Filter Frequency
(Min. Filter Frequency
1)
(see note
)
0
0.83Mpps (600ns)
0
3.33Mpps (150ns)
1
208Kpps (2.4us)
1
0.83Mpps (600ns)
2
104Kpps (4.8us)
2
416Kpps (1.2us)
3
52Kpps (9.6us)
3
208Kpps (2.4us)
4
No Filter Function
4
No Filter Function
7-21
Chapter 7 Servo Parameters
ASDA-B2
Pleae note:
1.
If an input pulse of 2~4MHz is used, it is recommended to change the setting value B (Input pulse
filter) and set this setting value to 4. Please note that this function is available for DSP version
V1.005 sub10 or above.
Note: If the signal is a 4Mpps high input pulse, setting the value B to 4 is able to ensure that the
signal will not be filtered and will be certainly delivered.
7-22
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
C: Input polarity
Logic
Pulse
Forward
Type
Reverse
AB
phase
pulse
0
Positive
CW +
Logic
CCW
pulse
T3
TH
Pulse
T2
T2
TH
T2
T2
T2
T2
T2
T2
T2
Sign
Pulse +
Direction
AB
Pulse
TH
phase
pulse
1
Negative
Logic
CW +
T1
Sign
T1
T1
T1 T1
T1
Pulse
T2
T2
T2
T3
TH
CCW
pulse
Sign
Pulse
TH
Pulse +
T4
Direction
T5
T6
T5
T6
T5
T4
Sign
Max.
input
pulse
frequency
Pulse specification
High-speed
pulse
Low-speed
pulse
Line
driver
Line
driver
Open
collector
T1
T2
T3
T4
T5
T6
4Mpps
62.5ns
125ns
250ns
200ns
125ns
125ns
500Kpps
0.5μs
1μs
2μs
2μs
1μs
1μs
200Kpps
1.25μs
2.5μs
5μs
5μs
2.5μs
2.5μs
Max. input pulse
frequency
Voltage
specification
Forward
specification
Line driver
4Mpps
5V
< 25mA
Line driver
500Kpps
2.8V ~ 3.7V
< 25mA
Open collector
200Kpps
24V (Max.)
< 25mA
Pulse specification
High-speed pulse
Low-speed pulse
Revision September 2013
Min. time width
7-23
Chapter 7 Servo Parameters
ASDA-B2
D: Source of pulse command
Setting value
Input pulse interface
CN1 Terminal Identification:
Open collector for low-speed pulse PULSE, SIGN
0
1
P1-01●
Remark
Line driver for high-speed pulse
CTL
CN1 Terminal Identification:
PULSE_D, SIGN_D
Control Mode and Output Direction
Operation
Keypad/Software
Communication
Interface:
Default: 0
Control
ALL
Mode:
Unit: pulse (P mode), r/min (S mode),
N-m (T mode)
Range: 00 ~ 110
Data Size: 16-bit
Display
Hexadecimal
Format:
Address: 0102H
0103H
Related Section:
Section 6.1,
Table 7.A
Settings:
A: Control mode settings
Mode
PT
S
T
Sz
Tz
Single Mode
00
▲
01
Reserved
02
▲
03
▲
04
▲
05
▲
Multiple Mode
06
▲
07
▲
▲
08
Reserved
09
Reserved
0A
7-24
▲
▲
▲
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Single Mode:
PT: Position control mode. The command is from external pulse or analog voltage
(external analog voltage will be available soon). Execution of the command
selection is via DI signal, PTAS.S: Speed control mode. The command is from
external signal or internal signal. Execution of the command selection is via DI
signals, SPD0 and SPD1.
T: Torque control mode. The command is from external signal or internal signal.
Execution of the command selection is via DI signals, TCM0 and TCM1.
Sz: Zero speed / internal speed command
Tz: Zero torque / internal torque commandMultiple Mode: Control of the mode selection
is via DI signals. For example, either PT or S control mode can be selected via DI
signals, S-P (see Table 7.A).
B: Torque output direction settings
Direction
0
1
Forward
Reverse
P1-02▲
PSTL
Speed and Torque Limit
Operation
Keypad/Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: Range: 00 ~ 11
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 0104H
0105H
Related Section:
Section 6.6,
Table 7.A
Settings:
 Disable or Enable speed limit function
0: Disable speed limit function
1: Enable speed limit function (It is available in torque mode)
Others: Reserved
Revision September 2013
7-25
Chapter 7 Servo Parameters
ASDA-B2
Speed limit setting is as the following:
Vref
(0)
P1-09(1)
P1-10(2)
P1-11(3)
Speed Limit
Command
SPD0
SPD1
Users could use speed limit function via parameter setting or DI triggering. That is to
say, set P1-02 to 0x0001 or trigger DI will do. Also, users could enable or disable the
limit function via DI. SPDLM, which is a more flexible way but would need to take one
DI setting. Speed limit can be enabled by P1-02 or DI.
DI.SPD0 and DI.SPD1 are for selecting the limiting source.
 Disable or Enable torque limit function
0: Disable torque limit function
1: Enable torque limit function (It is available in position and speed mode)
Other: Reserved
Tref
(0)
P1-12(1)
P1-13(2)
P1-14(3)
Torque Limit
Command
TCM0
TCM1
Users could use torque limit function via parameter setting or DI triggering. That is to
say, set P1-02 to 0x0010 or trigger DI will do. Also, users could enable or disable the
limit function via DI.TRQLM, which is a more flexible way but would need to take one
DI setting. Torque limit can be enabled by P1-02 or DI.
DI.TCM0 and DI.TCM1 are for selecting the limiting source.
P1-03
AOUT Pulse Output Polarity Setting
Operation
Keypad/Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: Range: 0 ~ 13
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 0106H
0107H
Related Section:
Section 3.3.3
Settings:
7-26
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
A: Analog monitor outputs polarity
0: MON1(+), MON2(+)
1: MON1(+), MON2(-)
2: MON1(-), MON2(+)
3: MON1(-), MON2(-)
P1-04
B: Position pulse outputs polarity
0: Forward output
1: Reverse output
MON1 Analog Monitor Output Proportion 1 (MON1)
Operation
Keypad/Software
Interface:
Default: 100
Control
ALL
Mode:
Unit: % (full scale)
Range: 0 ~ 100
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0108H
0109H
Related Section:
Section 6.4.4
Settings:
Please note:
For the setting of analog output voltage proportion, refer to the P1-03.
Example: P0-03 = 01 (MON1 is motor speed analog output, MON2 is motor torque
analog output)
Motor speed
MON1 output voltage= 8 ×
(Max. motor speed ×
P1-04
)
100
(unit: Volts)
Motor toque
MON2 output voltage= 8 ×
(Max. motor torque ×
P1-05
MON2 Analog Monitor Output Proportion 2 (MON2)
Operation
Keypad/Software
Interface:
Default: 100
Control
ALL
Mode:
Unit: % (full scale)
Range: 0 ~ 100
Revision September 2013
Communication
P1-05
)
100
(unit: Volts)
Address: 010AH
010BH
Related Section:
Section 6.4.4
7-27
Chapter 7 Servo Parameters
ASDA-B2
Data Size: 16-bit
Display
Decimal
Format:
Settings:
Please note:
For the setting of analog output voltage proportion, refer to the P1-03.
Example: P0-03 = 01 (MON1 is motor speed analog output, MON2 is motor torque
analog output)
Motor speed
MON1 output voltage= 8 ×
(Max. motor speed ×
P1-04
)
100
(unit: Volts)
Motor toque
MON2 output voltage= 8 ×
(Max. motor torque ×
P1-06
SFLT
Accel / Decel Smooth Constant of Analog
Speed Command (Low-pass Filter)
Operation
Keypad/Software
Communication
Interface:
Default: 0
Control
S
Mode:
Unit: ms
Range: 0 ~ 1000 (0: Disabled)
Data Size: 16-bit
Display
Decimal
Format:
P1-05
)
100
(unit: Volts)
Address: 010CH
010DH
Related Section:
Section 6.3.3
Settings: 0: Disabled
P1-07
TFLT
Smooth Constant of Analog Torque
Command (Low-pass Filter)
Operation
Keypad/Software
Communication
Interface:
Default: 0
Control
T
Mode:
Unit: ms
Range: 0 ~ 1000 (0: Disabled)
Data Size: 16-bit
Display
Decimal
Format:
Address: 010EH
010FH
Related Section:
Section 6.4.3
Settings: 0: Disabled
7-28
Revision September 2013
ASDA-B2
P1-08
Chapter 7 Servo Parameters
PFLT
Smooth Constant of Position Command
(Low-pass Filter)
Operation
Keypad/Software
Interface:
Default: 0
Control
PT
Mode:
Unit: 10ms
Range: 0 ~ 1000
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0110H
0111H
Related Section:
Section 6.2.4
Settings: 0: Disabled
For example: 11=110 msec
P1-09
SP1
1st Speed Command or Limit
Operation
Keypad/Software
Interface:
Default: 1000
Control
S, T
Mode:
Unit: 0.1r/min
Range: -50000 ~ +50000
Data Size: 32-bit
Display
Decimal
Format:
Communication
Address: 0112H
0113H
Related Section:
Section 6.3.1
Settings:
For example: 120=12 r/min
1st Speed Command
In Speed mode, this parameter is used to set speed 1 of internal speed command.
1st Speed Limit
In Torque mode, this parameter is used to set speed limit 1 of internal speed
command.
P1-10
SP2
2nd Speed Command or Limit
Operation
Keypad/Software
Interface:
Default: 2000
Control
S, T
Mode:
Unit: 0.1r/min
Range: -50000 ~ +50000
Data Size: 32-bit
Display
Decimal
Format:
Communication
Address: 0114H
0115H
Related Section:
Section 6.3.1
Settings:
Revision September 2013
7-29
Chapter 7 Servo Parameters
ASDA-B2
For example: 120=12 r/min
2nd Speed Command
In Speed mode, this parameter is used to set speed 2 of internal speed command.
2nd Speed Limit
In Torque mode, this parameter is used to set speed limit 2 of internal speed
command.
P1-11
SP3
3rd Speed Command or Limit
Operation
Keypad/Software
Interface:
Default: 3000
Control
S, T
Mode:
Unit: 0.1r/min
Range: -50000 ~ +50000
Data Size: 32-bit
Display
Decimal
Format:
Communication
Address: 0116H
0117H
Related Section:
Section 6.3.1
Settings:
For example: 120=12 r/min
3rd Speed Command
In Speed mode, this parameter is used to set speed 3 of internal speed command.
3rd Speed Limit
In Torque mode, this parameter is used to set speed limit 3 of internal speed
command.
P1-12
TQ1
1st Torque Command or Limit
Operation
Keypad/Software
Interface:
Default: 100
Control
T, P&S
Mode:
Unit: %
Range: -300 ~ +300
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0118H
0119H
Related Section:
Section 6.4.1
Settings:
1st Torque Command
In Torque mode, this parameter is used to set torque 1 of internal torque command.
1st Torque Limit
In Position and Speed mode, this parameter is used to set torque limit 1 of internal
torque command.
7-30
Revision September 2013
ASDA-B2
P1-13
Chapter 7 Servo Parameters
TQ2
2nd Torque Command or Limit
Operation
Keypad/Software
Interface:
Default: 100
Control
T, P&S
Mode:
Unit: %
Range: -300 ~ +300
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 011AH
011BH
Related Section:
Section 6.4.1
Settings:
2nd Torque Command
In Torque mode, this parameter is used to set torque 2 of internal torque command.
2nd Torque Limit
In Position and Speed mode, this parameter is used to set torque limit 2 of internal
torque command.
P1-14
TQ3
3rd Torque Command or Limit
Operation
Keypad/Software
Interface:
Default: 100
Control
T, P&S
Mode:
Unit: %
Range: -300 ~ +300
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 011CH
011DH
Related Section:
Section 6.4.1
Settings:
3rd Speed Command
In Torque mode, this parameter is used to set torque 3 of internal torque command.
3rd Speed Limit
In Position and Speed mode, this parameter is used to set torque limit 3 of internal
torque command.
P1-15
Reserved (Do Not Use)
Address: 011EH
011FH
P1-16
Reserved (Do Not Use)
Address: 0120H
0121H
P1-17
Reserved (Do Not Use)
Address: 0122H
0123H
P1-18
Reserved (Do Not Use)
Address: 0124H
0125H
Revision September 2013
7-31
Chapter 7 Servo Parameters
ASDA-B2
P1-19
Reserved (Do Not Use)
Address: 0126H
0127H
P1-20
Reserved (Do Not Use)
Address: 0128H
0129H
P1-21
Reserved (Do Not Use)
Address: 012AH
012BH
P1-22
Reserved (Do Not Use)
Address: 012CH
012DH
P1-23
Reserved (Do Not Use)
Address: 012EH
012FH
P1-25
VSF1
Low-frequency Vibration Suppression (1)
Address: 0132H
0133H
Related Section:
Section 6.2.9
Operation
Keypad/Software
Communication
Interface:
Default: 1000
Control
PT
Mode:
Unit: 0.1Hz
Range: 10 ~ 1000
Data Size: 16bit
Display
DEC
Format:
Example 150=15Hz
Settings: The setting value of the first low-frequency vibration suppression. If
P1-26 is set to 0, then it will disable the first low-frequency filter.
Low-frequency Vibration Suppression Gain
Address: 0134H
(1)
0135H
Related Section:
Operation
Keypad/Software
Communication
Interface:
Section 6.2.9
Default: 0
Control
PT
Mode:
Unit: Range: 0~9 (0: Disable the first low-frequency filter)
Data Size: 16bit
Display
DEC
Format:
Settings: The first low-frequency vibration suppression gain. The bigger value it
is, the better the position response will be. However, if the value is set
too big, the motor will not be able to smoothly operate. It is suggested
to set the value to 1.
P1-26
VSG1
P1-27
VSF2
Low-frequency Vibration Suppression (2)
Operation
Keypad/Software
Interface:
Default: 1000
7-32
Communication
Address: 0136H
0137H
Related Section:
Section 6.2.9
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Control
PT
Mode:
Unit: 0.1Hz
Range: 10 ~ 1000
Data Size: 16bit
Display
DEC
Format:
Example 150=15Hz
Settings: The setting value of the second low-frequency vibration suppression. If
P1-28 is set to 0, then it will disable the second low-frequency filter.
P1-28
P1-31
P1-32
Low-frequency Vibration Suppression Gain
Address: 0138H
(2)
0139H
Operation
Related Section:
Keypad/Software
Communication
Interface:
Section 6.2.9
Default: 0
Control
PT
Mode:
Unit: Range: 0~9 (0: Disable the second low-frequency
filter)
Data Size: 16bit
Display
DEC
Format:
Settings: The second low-frequency vibration suppression gain. The bigger value
it is, the better the position response will be. However, if the value is set
too big, the motor will not be able to smoothly operate. It is suggested
to set the value to 1.
VSG2
Address: 013EH
013FH
Reserved (Do Not Use)
LSTP
Motor Stop Mode Selection
Operation
Keypad/Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: Range: 0 ~ 20
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 0140H
0141H
Related Section: N/A
Settings:
Revision September 2013
7-33
Chapter 7 Servo Parameters
ASDA-B2
A: Fault Stop Mode
When a fault occurs (except for CWL, CCWL, EMGS and serial communication
error), it is used to set servo motor stop mode.
0: Stop instantly
1: Decelerate to stop
B: Dynamic Brake Option
When Servo Off or a fault (servo alarm) occurs, it is used to set servo motor stop
mode.
0: Use dynamic brake
1: Allow servo motor to coast to stop
2: Use dynamic brake first, after the motor speed is below than P1-38, allow servo
motor to coast to stop
When the fault NL(CWL) or PL(CCWL) occurs, please refer to the settings of
parameter P1-06, P1-35, P1-36 to determine the deceleration time. If the deceleration
time is set to 1ms, the motor will stop instantly.
P1-33
P1-34
Address: 0142H
0143H
Reserved (Do Not Use)
TACC
Acceleration Time
Operation
Keypad/Software
Interface:
Default: 200
Control
S
Mode:
Unit: ms
Range: 1 ~ 20000
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0144H
0145H
Related Section:
Section 6.3.3
Settings:
This parameter is used to determine the acceleration time to accelerate from 0 to its
rated motor speed. The functions of parameters P1-34, P1-35 and P1-36 are each
individual.
Please note:
1. When the source of speed command is analog command, the maximum setting
value of P1-36 is set to 0, the acceleration and deceleration function will be
disabled.
7-34
Revision September 2013
ASDA-B2
P1-35
Chapter 7 Servo Parameters
TDEC
Deceleration Time
Operation
Keypad/Software
Interface:
Default: 200
Control
S
Mode:
Unit: ms
Range: 1 ~ 20000
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0146H
0147H
Related Section:
Section 6.3.3
Settings:
This parameter is used to determine the acceleration time to accelerate from 0 to its
rated motor speed. The functions of parameters P1-34, P1-35 and P1-36 are each
individual.
Please note:
1. When the source of speed command is analog command, the maximum setting
value of P1-36 is set to 0, the acceleration and deceleration function will be
disabled.
P1-36
TSL
Accel /Decel S-curve
Operation
Keypad/Software
Communication
Interface:
Default: 0
Control
S
Mode:
Unit: ms
Range: 0 ~ 10000 (0: Disabled)
Data Size: 16-bit
Display
Decimal
Format:
Address: 0148H
0149H
Related Section:
Section 6.3.3
Settings:
This parameter is used to make the motor run more smoothly when startup and
windup. Using this parameter can improve the motor running stability.
TACC: P1-34, Acceleration time
TDEC: P1-35, Deceleration time
TSL: P1-36, Accel /Decel S-curve
Total acceleration time = TACC + TSL
Total deceleration time = TDEC + TSL
Revision September 2013
7-35
Chapter 7 Servo Parameters
ASDA-B2
The functions of parameters P1-34, P1-35 and P1-36 are each individual. When
P1-36 is set to 0 (Disabled), the settings of P1-34, P1-35 are still effective. It indicates
that the parameters P1-34 and P1-35 will not become disabled even when P1-36 is
disabled.
Please note:
1. When the source of speed command is analog command, the maximum setting
value of P1-36 is set to 0, the acceleration and deceleration function will be
disabled.
P1-37
GDR
Ratio of Load Inertia to Servo Motor Inertia
Operation
Keypad/Software
Interface:
Default: 1.0
Control
ALL
Mode:
Unit: 1 times
Range: 0.0 ~ 200.0
Data Size: 16-bit
Display
One-digit
Format:
Input Value
1.5 = 1.5 times
Example:
Communication
Address: 014AH
014BH
Related Section: N/A
10
0.1 times
0 ~ 2000
Decimal
15 = 1.5 times
Settings:
Ratio of load inertia to servo motor inertia (for Rotation Motor): (J_load
/J_motor)
J_load: Total equivalent moment of inertia of external mechanical load
J_motor: Moment of inertia of servo motor
P1-38
ZSPD
Zero Speed Range Setting
Operation
Keypad/Software
Interface:
Default: 10.0
Control
ALL
Mode:
Unit: 1 r/min
Range: 0.0 ~ 200.0
Data Size: 16-bit
Display
One-digit
Format:
Input Value
1.5 = 1.5 r/min
Example:
Communication
Address: 014CH
014DH
Related Section:
Table 7.B
100
0.1 r/min
0 ~ 2000
Decimal
15 = 1.5 r/min
Settings:
This parameter is used to set output range of zero speed signal (ZSPD) and
determine when zero speed signal (ZSPD) becomes activated. ZSPD is activated
when the drive senses the motor is equal to or below the Zero Speed Range setting
as defined in parameter P1-38.
For Example, at default ZSPD will be activated when the drive detects the motor
7-36
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
rotating at speed at or below 100 r/min. ZSPD will remain activated until the motor
speed increases above 100 r/min.
P1-39
SSPD
Target Motor Speed
Operation
Keypad/Software
Interface:
Default: 3000
Control
ALL
Mode:
Unit: r/min
Range: 0 ~ 5000
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 014EH
014FH
Related Section:
Table 7.B
Settings:
When target motor speed reaches its preset value, digital output (TSPD) is enabled.
When the forward and reverse speed of servo motor is equal and higher than the
setting value, the motor will reach the target motor speed, and then TSPD signal will
output.
TSPD is activated once the drive has detected the motor has reached the Target
Motor Speed setting as defined in parameter P1-39. TSPD will remain activated until
the motor speed drops below the Target Motor Speed.
P1-40▲
VCM
Max. Analog Speed Command or Limit
Operation
Keypad/Software
Interface:
Default: rated speed
Control
S, T
Mode:
Unit: r/min
Range: 0 ~ 10000
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0150H
0151H
Related Section:
Section 6.3.4
Settings:
In Speed mode, this parameter is used to set the maximum analog speed command
based on the maximum input voltage (10V).
In Torque mode, this parameter is used to set the maximum analog speed limit based
on the maximum input voltage (10V).
For example, in speed mode, if P1-40 is set to 3000 and the input voltage is 10V, it
indicates that the speed command is 3000 r/min. If P1-40 is set to 3000, but the input
voltage is changed to 5V, then the speed command is changed to 1500 r/min.
Speed Command / Limit = Input Voltage Value x Setting value of P1-40 / 10
Revision September 2013
7-37
Chapter 7 Servo Parameters
P1-41▲
TCM
ASDA-B2
Max. Analog Torque Command or Limit
Operation
Keypad/Software
Interface:
Default: 100
Control
ALL
Mode:
Unit: %
Range: 0 ~ 1000
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0152H
0153H
Related Section:
Section 6.4.4
Settings:
In Torque mode, this parameter is used to set the maximum analog torque command
based on the maximum input voltage (10V).
In PT and Speed mode, this parameter is used to set the maximum analog torque
limit based on the maximum input voltage (10V).
For example, in torque mode, if P1-41 is set to 100 and the input voltage is 10V, it
indicates that the torque command is 100% rated torque. If P1-41 is set to 100, but the
input voltage is changed to 5V, then the torque command is changed to 50% rated
torque.
Torque Command / Limit = Input Voltage Value x Setting value of P1-41 / 10
P1-42
MBT1
On Delay Time of Electromagnetic Brake
Operation
Keypad/Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: ms
Range: 0 ~ 1000
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0154H
0155H
Related Section:
Section 6.5.5
Settings:
Used to set the period of time between when the servo drive is On (Servo On) and
when electromagnetic brake output signal (BRKR) is activated.
P1-43
MBT2
OFF Delay Time of Electromagnetic Brake
Operation
Keypad/Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: ms
Range: -1000 ~ +1000
Data Size: 16-bit
7-38
Communication
Address: 0156H
0157H
Related Section:
Section 6.5.5
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Display
Decimal
Format:
Settings:
Used to set the period of time between when the servo drive is Off (Servo Off) and
when electromagnetic brake output signal (BRKR) is inactivated.
Please note:
1. When servo is commanded off and the off delay time set by P1-43 has not elapsed,
if the motor speed is lower than the setting value of P1-38, the electromagnetic
brake will be engaged regardless of the off delay time set by P1-43.
2. When servo is commanded off and the off delay time set by P1-43 has elapsed, if
the motor speed is higher than the setting value of P1-38, electromagnetic brake
will be engaged regardless of the current motor speed.
3. When the servo drive is disabled (Servo Off) due to a fault (except AL022) or by
EMGS (Emergency stop)) being activated, if the off delay time set by P1-43 is a
negative value, it will not affect the operation of the motor. A negative value of the
off delay time is equivalent to one with a zero value.
P1-44▲
GR1
Electronic Gear Ratio (1st Numerator) (N1)
Operation
Keypad/Software
Interface:
Default: 16
Control
PT
Mode:
Unit: pulse
Range: 1 ~ (226-1)
Data Size: 32-bit
Display
Decimal
Format:
Communication
Address: 0158H
0159H
Related Section:
Section 6.2.3
Settings:
This parameter is used to set the numerator of the electronic gear ratio. The
denominator of the electronic gear ratio is set by P1-45. P2-60 ~ P2-62 are used to
set the additional numerators.
Please note:
1. In PT mode, the setting value of P1-44 can be changed only when the servo drive
is enabled (Servo On).
Revision September 2013
7-39
Chapter 7 Servo Parameters
P1-45▲
GR2
ASDA-B2
Electronic Gear Ratio (Denominator) (M)
Operation
Keypad/Software
Interface:
Default: 10
Control
PT
Mode:
Unit: pulse
Range: 1 ~ (231-1)
Data Size: 32-bit
Display
Decimal
Format:
Communication
Address: 015AH
015BH
Related Section:
Section 6.2.3
Settings:
This parameter is used to set the denominator of the electronic gear ratio. The
numerator of the electronic gear ratio is set by P1-44. P2-60 ~ P2-62 are used to set
the additional numberators.
As the wrong setting may cause motor to run chaotically (out of control) and it may
lead to personnel injury, therefore, ensure to observe the following rule when setting
P1-44, P1-45.
The electronic gear ratio setting (Please also see P1-44, P2-60 ~ P2-62):
Pulse input
f1
N
M
Position
command
N
f2 = f1 x M
f1: Pulse input
f2: Position command
N: Numerator, the setting value of P1-44 or
P2-60 ~ P2-62
M: Denominator, the setting value of P1-45
The electronic gear ratio setting range must be within: 1/50<N/M<25600.
Please note:
1. In PT mode, the setting value of P1-45 can not be changed when the servo drive
is enabled (Servo On).
P1-46▲
GR3
Encoder Output Pulse Number
Operation
Keypad/Software
Interface:
Default: 2500
Control
ALL
Mode:
Unit: pulse
Range: 4 ~ 40000
Data Size: 32-bit
Display
Decimal
Format:
Communication
Address: 015CH
015DH
Related Section: N/A
Settings:
This parameter is used to set the pulse numbers of encoder outputs per motor
revolution.
Please note: When the following conditions occur, the output frequency for pulse
output may exceed the specification and cause that the servo drive fault AL018
(Encoder Output Error) is activated.
7-40
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Condition 1: Encoder error.
Condition 2: Motor speed is above the value set by parameter P1-76.
P1-47
SPOK Speed Reached Output Range
Operation
Keypad/Software
Interface:
Default: 10
Control
S, Sz
Mode:
Unit: r/min
Range: 0 ~ 300
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 015EH
015FH
Related Section: N/A
Settings:
This parameter is used to set the speed reached output range. The DO signal,
SP_OK (0x19) will be activated when the speed error is equal and below the setting
value of P1-47.
1. Speed Command: It is the speed command input by the users (no Accel/Decel), not
the frond-end command of speed control loop. The source of this command
includes analog voltage and registers.
2. Feedback Speed: It is the actual motor speed which is filtered.
3. Get Absolute Value
4. Judge if the speed error is equal and below the setting value of P1-47: When P1-47
is set to 0, this digital output will be always off.
5. ON or OFF: When the speed error is equal and below the setting value of P1-47,
SP_OK will be ON; otherwise, SP_OK will be OFF.
P1-48
Reserved (Do Not Use)
Address: 0160H
0161H
P1-49
Reserved (Do Not Use)
Address: 0162H
0163H
Revision September 2013
7-41
Chapter 7 Servo Parameters
ASDA-B2
P1-50
Reserved (Do Not Use)
Address: 0164H
0165H
P1-51
Reserved (Do Not Use)
Address: 0166H
0167H
P1-52
RES1
Regenerative Resistor Value
Operation
Keypad/Software
Interface:
Default: See the table below
Control
ALL
Mode:
Unit: Ohm
Range: 10 ~ 750
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0168H
0169H
Related Section:
Section 6.6.3
Settings:
This parameter is used to set the resistance of the applicable regenerative resistor.
Model
P1-53
Default
For 750W models
100Ω
For 1kW to 3kW models
40Ω
RES2
Regenerative Resistor Capacity
Operation
Keypad/Software
Interface:
Default: See the table below
Control
ALL
Mode:
Unit: Watt
Range: 30 ~ 3000
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 016AH
016BH
Related Section:
Section 6.6.3
Settings:
This parameter is used to set the capacity of the applicable regenerative resistor.
Model
7-42
Default
For 750W models
60W
For 1kW to 3kW models
60W
Revision September 2013
ASDA-B2
P1-54
Chapter 7 Servo Parameters
PER
Positioning Completed Width
Operation
Keypad/Software
Interface:
Default: 1600
Control
PT
Mode:
Unit: pulse
Range: 0 ~ 1280000
Data Size: 32-bit
Display
Decimal
Format:
Communication
Address: 016CH
016DH
Related Section:
Table 7.B
Settings:
In PT mode, when the error pulse numbers is less than the setting value of parameter
P1-54, TPOS (At positioning completed signal) will be activated.
P1-55
MSPD Maximum Speed Limit
Operation
Keypad/Software
Interface:
Default: rated speed
Control
ALL
Mode:
Unit: r/min
Range: 0 ~ Max. speed
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 016EH
016FH
Related Section: N/A
Settings:
This parameter is used to set maximum motor speed. The default setting is rated
speed.
P1-56
OVW
Output Overload Warning Time
Operation
Keypad/Software
Interface:
Default: 120
Control
ALL
Mode:
Unit: %
Range: 0 ~ 120
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0170H
0171H
Related Section: N/A
Settings:
This parameter is used to set output overload time. If the setting value of parameter
P1-56 is set to 0 ~ 100, the function of parameter P1-56 is enabled. When the motor
has reached the output overload time set by parameter P1-56, the motor will send a
warning to the drive. After the drive has detected the warning, the DO signal OLW will
Revision September 2013
7-43
Chapter 7 Servo Parameters
ASDA-B2
be activated. If the setting value of parameter P1-56 exceeds 100, the function of
parameter P1-56 is disabled.
tOL = Permissible Time for Overload x the setting value of parameter P1-56
When overload accumulated time (continuously overload time) exceeds the value of
tOL, the overload warning signal will output, i.e. DO signal, OLW will be ON. However,
if the accumulated overload time (continuous overload time) exceeds the permissible
time for overload, the overload alarm (AL006) will occur.
For example:
If the setting value of parameter P1-56 (Output Overload Warning Time) is 60%, when
the permissible time for overload exceeds 8 seconds at 200% rated output, the
overload fault (AL006) will be detected and shown on the LED display.
At this time, tOL = 8 x 60% = 4.8 seconds
Result:
When the drive output is at 200% rated output and the drive is continuously
overloaded for 4.8 seconds, the overload warning signal will be ON, i.e. DO signal
OLW will be activated. If the drive is continuously overloaded for 8 seconds, the
overload alarm will be detected and shown on the LED display (AL006). Then, Servo
Fault signal will be ON (DO signal ALRM will be activated).
P1-57
CRSHA Motor Protection Percentage
Operation
Keypad/Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: %
Range: 0 ~ 300
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0172H
0173H
Related Section: N/A
Settings:
This parameter is used to protect the motor in case the motor touchs the mechanical
equipment. If P1-57 is set to 0, the function of P1-57 is disabled.
The function of P1-57 is enabled when the setting value of P1-57 is set to 1 or more.
The fault AL030 will be activated when the setting value of P1-57 is reached after a
period of time set by P1-58.
P1-58
CRSHT Motor Protection Time
Operation
Keypad/Software
Interface:
Default: 1
Control
ALL
Mode:
Unit: ms
Range: 0 ~ 1000
Data Size: 16-bit
7-44
Communication
Address: 0174H
0175H
Related Section: N/A
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Display
Decimal
Format:
Settings:
This parameter is used to protect the motor in case the motor touchs the mechanical
equipment. The fault AL030 will be activated when the setting value of P1-57 is
reached after a period of time set by P1-58.
Please note that this function is applicable for non-contact applications, such as
electric discharge machines only (P1-37 must be set correctly).
P1-59
MFLT
Analog Speed Linear Filter (Moving Filter)
Operation
Keypad/Software
Interface:
Default: 0.0
Control
S
Mode:
Unit: 1 ms
Range: 0.0 ~ 4.0
(0: Disabled)
Data Size: 16-bit
Display
One-digit
Format:
Input Value
1.5 = 1.5 ms
Example:
Communication
Address: 0176H
0177H
Related Section: N/A
0
0.1 ms
0 ~ 40
(0: Disabled)
Decimal
15 = 1.5 ms
Settings:
This parameter is used to eliminate the noise generated during the operation when
the host (external) controller sends the step analog voltage speed command. The
parameter P1-06 is Low-pass Filter and parameter P1-59 is Moving Filter. The
differences are that Low-pass Filter is usually used to smooth the end of the
command but Moving Filter can be used to smooth the start and the end of step
analog voltage speed command. Using Moving Filter can facilitate the smooth
operation of the motor very effectively.
Therefore, it is recommended to use P1-06 Low-pass Filter when the speed command
from the external controller is applied for position control loop. If the command is for
speed control only, using Moving Filter P1-59 can achieve better (smooth)
performance.
Revision September 2013
7-45
Chapter 7 Servo Parameters
ASDA-B2
P1-60
Reserved (Do Not Use)
Address: 0178H
0179H
P1-61
Reserved (Do Not Use)
Address: 017AH
017BH
P1-62
FRCL
Friction Compensation Percentage
Operation
Keypad/Software
Interface:
Default: 0
Control
PT, S
Mode:
Unit: %
Range: 0 ~ 100
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 017CH
017DH
Related Section: N/A
Settings:
This parameter is used to set the torque percentage for friction compensation. If
P1-62 is set to 0, the function of P1-62 is disabled. The function of P1-62 is enabled
when the setting value of P1-62 is set to 1 or more.
P1-63
FRCT
Friction Compensation Percentage
Operation
Keypad/Software
Interface:
Default: 0
Control
PT, S
Mode:
Unit: ms
Range: 0 ~ 1000
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 017EH
017FH
Related Section: N/A
Settings:
This parameter is used to set the smooth constant of friction compensation.
7-46
P1-64
Reserved (Do Not Use)
Address: 0180H
0181H
P1-65
Reserved (Do Not Use)
Address: 0182H
0183H
P1-66
Reserved (Do Not Use)
Address: 0184H
0185H
P1-67
Reserved (Do Not Use)
Address: 0186H
0187H
Revision September 2013
ASDA-B2
P1-68
Chapter 7 Servo Parameters
PFLT2 Position Command Moving Filter 1
Operation
Keypad/Software
Communication
Interface:
Default: 4
Control
PT
Mode:
Unit: ms
Range: 0 ~ 100 (0: Disabled)
Data Size: 16-bit
Display
Decimal
Format:
Address: 0188H
0189H
Related Section: N/A
Settings:
Moving Filter can be used to smooth the start and the end of step position command.
Using Moving Filter can facilitate the smooth operation of the motor very effectively,
but it will cause command delay.
P1-69
Reserved (Do Not Use)
Address: 018AH
018BH
P1-70
Reserved (Do Not Use)
Address: 018CH
018DH
P1-71
Reserved (Do Not Use)
Address: 018EH
018FH
P1-72
Reserved (Do Not Use)
Address: 0190H
0191H
P1-73
Reserved (Do Not Use)
Address: 0192H
0193H
P1-74
Reserved (Do Not Use)
Address: 0194H
0195H
P1-75
Reserved (Do Not Use)
Address: 0196H
0197H
Revision September 2013
7-47
Chapter 7 Servo Parameters
P1-76
AMSPD Max. Rotation Speed of Encoder Output
Operation
Keypad/Software
Communication
Interface:
Default: 5500
Control
ALL
Mode:
Unit: r/min
Range: 0 ~ 6000 (0: Disabled)
Data Size: 16-bit
Display
Decimal
Format:
ASDA-B2
Address: 0198H
0199H
Related Section: P1-46
Settings:
This parameter is used to optimize the encoder outputs (OA, OB). When the users set
the actual reached maximum motor speed, the servo drive will equalize the encoder
outputs automatically. When P1-76 is set to 0, it indicates that equalizing function is
not available.
P1-77
PFLT3 Position Command Moving Filter 2
Operation
Keypad/Software
Communication
Interface:
Default: 4
Control
PT
Mode:
Unit: ms
Range: 0 ~ 100 (0: Disabled)
Data Size: 16-bit
Display
Decimal
Format:
Address: 019AH
019BH
Related Section: N/A
Settings:
Moving Filter can be used to smooth the start and the end of step position command.
Using Moving Filter can facilitate the smooth operation of the motor very effectively,
but it will cause command delay.
7-48
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Group 2: P2-xx
P2-00
Extension Parameters
KPP
Proportional Position Loop Gain
Operation
Keypad/Software
Interface:
Default: 35
Control
PT
Mode:
Unit: rad/s
Range: 0 ~ 2047
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0200H
0201H
Related Section:
Section 6.2.5
Settings:
This parameter is used to set the position loop gain. It can increase stiffness, expedite
position loop response and reduce position error. However, if the setting value is over
high, it may generate vibration or noise.
P2-01
PPR
Position Loop Gain Switching Rate
Operation
Keypad/Software
Interface:
Default: 100
Control
PT
Mode:
Unit: %
Range: 10 ~ 500
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0202H
0203H
Related Section:
Section 6.2.5
Settings:
This parameter is used to set the position gain switching rate when the gain switching
condition is satisfied. Please refer to P2-27 for gain switching control selection
settings and refer to P2-29 for gain switching condition settings.
P2-02
PFG
Position Feed Forward Gain
Operation
Keypad/Software
Interface:
Default: 50
Control
PT
Mode:
Unit: %
Range: 0 ~ 100
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0204H
0205H
Related Section:
Section 6.2.5
Settings:
This parameter is used to set the feed forward gain when executing position control
Revision September 2013
7-49
Chapter 7 Servo Parameters
ASDA-B2
command. When using position smooth command, increase gain can improve
position track deviation. When not using position smooth command, decrease gain
can improve the resonance condition of mechanical system.
P2-03
PFF
Smooth Constant of Position Feed Forward
Gain
Operation
Keypad/Software
Interface:
Default: 5
Control
PT
Mode:
Unit: ms
Range: 2 ~ 100
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0206H
0207H
Related Section: N/A
Settings:
When using position smooth command, increase gain can improve position track
deviation. When not using position smooth command, decrease gain can improve the
resonance condition of mechanical system.
P2-04
KVP
Proportional Speed Loop Gain
Operation
Keypad/Software
Interface:
Default: 500
Control
ALL
Mode:
Unit: rad/s
Range: 0 ~ 8191
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0208H
0209H
Related Section:
Section 6.3.6
Settings:
This parameter is used to set the speed loop gain. When the value of proportional
speed loop gain is increased, it can expedite speed loop response. However, if the
setting value is over high, it may generate vibration or noise.
P2-05
SPR
Speed Loop Gain Switching Rate
Operation
Keypad/Software
Interface:
Default: 100
Control
ALL
Mode:
Unit: %
Range: 10 ~ 500
Data Size: 16-bit
Display
Decimal
Format:
7-50
Communication
Address: 020AH
020BH
Related Section: N/A
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Settings:
This parameter is used to set the speed gain switching rate when the gain switching
condition is satisfied. Please refer to P2-27 for gain switching control selection
settings and refer to P2-29 for gain switching condition settings.
P2-06
KVI
Speed Integral Compensation
Operation
Keypad/Software
Interface:
Default: 100
Control
ALL
Mode:
Unit: rad/s
Range: 0 ~ 1023
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 020CH
020DH
Related Section:
Section 6.3.6
Settings:
This parameter is used to set the integral time of speed loop. When the value of speed
integral compensation is increased, it can improve the speed response ability and
decrease the speed control deviation. However, if the setting value is over high, it may
generate vibration or noise.
P2-07
KVF
Speed Feed Forward Gain
Operation
Keypad/Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: %
Range: 0 ~ 100
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 020EH
020FH
Related Section:
Section 6.3.6
Settings:
This parameter is used to set the feed forward gain when executing speed control
command.
When using speed smooth command, increase gain can improve speed track
deviation.
When not using speed smooth command, decrease gain can improve the resonance
condition of mechanical system.
P2-08■
PCTL
Special Factory Setting
Operation
Keypad/Software
Interface:
Default: 0
Revision September 2013
Communication
Address: 0210H
0211H
Related Section: N/A
7-51
Chapter 7 Servo Parameters
ASDA-B2
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 65535
Data Size: 16-bit
Display
Decimal
Format:
Settings:
Special parameter setting:
Parameter
code
Function
Parameter reset (Please re-power on the
servo drive after reseting)
Set P2-08 to 20 can change the value of
P4-10
Set P2-08 to 22 can change the value of
P4-11~P4-19
10
20
22
406
DO mode will be forced to be activated.
400
When force to activate the DO mode, set
P2-08 to 400 can switch the mode back to
normal DO mode.
Password protective setting for protecting the parameter from the end-users:
1. After enter the 5 digital numbers, please enter the same password again. And
the setting shall be finished.
2. When turning on the power again, the proctective password will be activated.
Parameter setting after setting up the password:
When entering the correct password, the parameter can be set.
Clear the password: After entering the correct password, please enter “0” twice
continuously.
P2-09
DRT
Bounce Filter
Operation
Keypad/Software
Interface:
Default: 2
Control
ALL
Mode:
Unit: 2ms
Range: 0 ~ 20
Data Size: 16-bit
Display
Decimal
Format:
Input Value
4 = 8 ms
Example:
Communication
Address: 0212H
0213H
Related Section: N/A
Settings:
7-52
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
For example, if P2-09 is set to 4, the bounce filter time is 4 x 2ms = 8ms.
When there are too much vibration or noises around environment, increasing this
setting value (bounce filter time) can improve reliability. However, if the time is too
long, it may affect the response time.
P2-10
DI1
Digital Input Terminal 1 (DI1)
Operation
Keypad/Software
Interface:
Default: 101
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 015Fh
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 0214H
0215H
Related Section:
Table 7.A
Settings:
The parameters from P2-10 to P2-17 and P2-36 are used to determine the functions
and statuses of DI1 ~ DI8.
A: DI (Digital Input) Function Settings:
For the setting value of P2- 10 ~ P2-17 and P2-36, please refer to Table 7.A.
B: DI (Digital Input) Enabled Status Settings:
0: Normally closed (contact b)
1: Normally open (contact a)
For example, when P2-10 is set to 101, it indicates that the function of DI1 is SON
(Servo On, setting value is 0x01) and it requires a normally open contact to be
connected to it.
Please re-start the servo drive after parameters have been changed.
Please note:
The parameter P3-06 is used to set how the Digital Inputs (DI) accept commands and
signals through the external terminals or via the communication which is determined
by parameter P4-07.
P2-11
DI2
Digital Input Terminal 2 (DI2)
Operation
Keypad/Software
Interface:
Default: 104
Control
ALL
Mode:
Unit: N/A
Revision September 2013
Communication
Address: 0216H
0217H
Related Section:
Table 7.A
7-53
Chapter 7 Servo Parameters
ASDA-B2
Range: 0 ~ 015Fh
Data Size: 16-bit
Display
Hexadecimal
Format:
Settings: Refer to P2-10 for explanation.
P2-12
DI3
Digital Input Terminal 3 (DI3)
Operation
Keypad/Software
Interface:
Default: 116
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 015Fh
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 0218H
0219H
Related Section:
Table 7.A
Settings: Refer to P2-10 for explanation.
P2-13
DI4
Digital Input Terminal 4 (DI4)
Operation
Keypad/Software
Interface:
Default: 117
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 015Fh
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 021AH
021BH
Related Section:
Table 7.A
Settings: Refer to P2-10 for explanation.
P2-14
DI5
Digital Input Terminal 5 (DI5)
Operation
Keypad/Software
Interface:
Default: 102
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 015Fh
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 021CH
021DH
Related Section:
Table 7.A
Settings: Refer to P2-10 for explanation.
7-54
Revision September 2013
ASDA-B2
P2-15
Chapter 7 Servo Parameters
DI6
Digital Input Terminal 6 (DI6)
Operation
Keypad/Software
Interface:
Default: 22
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 015Fh
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 021EH
021FH
Related Section:
Table 7.A
Settings: Refer to P2-10 for explanation.
P2-16
DI7
Digital Input Terminal 7 (DI7)
Operation
Keypad/Software
Interface:
Default: 23
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 015Fh
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 0220H
0221H
Related Section:
Table 7.A
Settings: Refer to P2-10 for explanation.
P2-17
DI8
Digital Input Terminal 8 (DI8)
Operation
Keypad/Software
Interface:
Default: 21
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 015Fh
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 0222H
0223H
Related Section:
Table 7.A
Settings: Refer to P2-10 for explanation.
P2-18
DO1
Digital Output Terminal 1 (DO1)
Operation
Keypad/Software
Interface:
Default: 101
Control
ALL
Mode:
Unit: N/A
Revision September 2013
Communication
Address: 0224H
0225H
Related Section:
Table 7.B
7-55
Chapter 7 Servo Parameters
ASDA-B2
Range: 0 ~ 013Fh
Data Size: 16-bit
Display
Hexadecimal
Format:
Settings:
The parameters from P2-18 to P2-22 and P2-37 are used to determine the functions
and statuses of DO1 ~ DO5.
A: DO Function Settings:
For the setting value of P2- 18 ~ P2-22 and P2-37, please refer to Table 7.B.
B: DO Enabled Status Settings:
0: Normally closed (contact b)
1: Normally open (contact a)
For example, when P2-18 is set to 101, it indicates that the function of DO1 is SRDY
(Servo ready, setting value is 0x01) and it requires a normally open contact to be
connected to it.
Please re-start the servo drive after parameters have been changed.
P2-19
DO2
Digital Output Terminal 2 (DO2)
Operation
Keypad/Software
Interface:
Default: 103
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 013Fh
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 0226H
0227H
Related Section:
Table 7.B
Settings: Refer to P2-18 for explanation.
P2-20
DO3
Digital Output Terminal 3 (DO3)
Operation
Keypad/Software
Interface:
Default: 109
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 013Fh
Data Size: 16-bit
Display
Hexadecimal
Format:
7-56
Communication
Address: 0228H
0229H
Related Section:
Table 7.B
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Settings: Refer to P2-18 for explanation.
P2-21
DO4
Digital Output Terminal 4 (DO4)
Operation
Keypad/Software
Interface:
Default: 105
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 013Fh
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 022AH
022BH
Related Section:
Table 7.B
Settings: Refer to P2-18 for explanation.
P2-22
DO5
Digital Output Terminal 5 (DO5)
Operation
Keypad/Software
Interface:
Default: 7
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 013Fh
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 022CH
022DH
Related Section:
Table 7.B
Settings: Refer to P2-18 for explanation.
P2-23
NCF1
Notch Filter 1 (Resonance Suppression)
Operation
Keypad/Software
Interface:
Default: 1000
Control
ALL
Mode:
Unit: Hz
Range: 50 ~ 2000
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 022EH
022FH
Related Section:
Section 6.2.5
Settings:
This parameter is used to set first resonance frequency of mechanical system. It can
be used to suppress the resonance of mechanical system and reduce the vibration of
mechanical system.
If P2-24 is set to 0, this parameter is disabled.
The parameters P2-23 and P2-24 are the first group of notch filter parameters and the
parameters P2-43 and P2-44 are the second group of notch filter parameters.
Revision September 2013
7-57
Chapter 7 Servo Parameters
P2-24
DPH1
ASDA-B2
Notch Filter Attenuation Rate 1
(Resonance Suppression)
Operation
Keypad/Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: dB
Range: 0 ~ 32 (0: Disabled)
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0230H
0231H
Related Section:
Section 6.3.7
Settings:
This parameter is used to set magnitude of the resonance suppression that is set by
parameter P2-23. If P2-24 is set to 0, the parameters P2-23 and P2-24 are both
disabled.
The parameters P2-23 and P2-24 are the first group of notch filter parameters and the
parameters P2-43 and P2-44 are the second group of notch filter parameters.
P2-25
Low-pass Filter Time Constant
(Resonance Suppression)
Operation
Keypad/Software
Communication
Interface:
Default: 0.2 (1kW and below 2 (1kW and below
models) or 0.5 (other models) or 5 (other
models)
models)
Control
ALL
Mode:
Unit: 1ms
0.1ms
Range: 0.0 ~ 100.0
0 ~ 1000
Data Size: 16-bit
Display
One-digit
Decimal
Format:
Input Value
1.5 = 1.5 ms
15 = 1.5 ms
Example:
NLP
Address: 0232H
0233H
Related Section:
Section 6.3.7
Settings:
This parameter is used to set low-pass filter time constant of resonance suppression.
If P2-25 is set to 0, this parameter is disabled.
P2-26
DST
External Anti-Interference Gain
Operation
Keypad/Software
Communication
Interface:
Default: 0
Control
ALL
Mode:
Unit: 0.001
Range: 0 ~ 1023 (0: Disabled)
Data Size: 16-bit
7-58
Address: 0234H
0235H
Related Section: N/A
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Display
Decimal
Format:
Settings:
If P2-26 is set to 0, this parameter is disabled.
This parameter is used to increase the damping factor of speed loop. It is
recommended to set the setting value of P2-26 to be equal to the setting value of
P2-06.
Please note:
1. In speed mode, increasing the parameter value of P2-26 can reduce speed
overshoot.
2. In position mode, decreasing the parameter value of P2-26 can reduce position
overshoot.
P2-27
GCC
Gain Switching Control Selection
Operation
Keypad/Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 4
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 0236H
0237H
Related Section: N/A
Settings:
Gain Switching Condition Settings:
A: Gain Switching Condition Settings:
0: Disabled
1: Gain switching DI (Digital Input) signal (GAINUP) is On. (see Table 8.A)
2: In position mode, position deviation is higher than the setting value of P2-29.
3: Position command frequency is higher than the setting value of P2-29.
4: Servo motor speed is higher than the setting value of P2-29.
5: Gain switching DI (Digital Input) signal (GAINUP) is Off. (see Table 8.A)
6: In position mode, position deviation is lower than the setting value of P2-29.
7: Position command frequency is lower than the setting value of P2-29.
8: Servo motor speed is lower than the setting value of P2-29.
B: Gain Switching Control Settings:
0: Gain multiple switching
Revision September 2013
7-59
Chapter 7 Servo Parameters
ASDA-B2
1: P  PI switching
Setting
0
1
P2-28
GUT
P mode
S mode
Status
P2-00 x 100%
P2-04 x 100%
P2-04 x 100%
Before switching
P2-00 x P2-01
P2-04 x P2-05
P2-04 x P2-05
After switching
P2-06 x 0%
P2-26 x 0%
Before switching
P2-06 x 100%
P2-26 x 100%
After switching
Gain Switching Time Constant
Operation
Keypad/Software
Communication
Interface:
Default: 10
Control
ALL
Mode:
Unit: 10ms
Range: 0 ~ 1000 (0: Disabled)
Data Size: 16-bit
Display
Decimal
Format:
Input Value
15 = 150 ms
Example:
Address: 0238H
0239H
Related Section: N/A
Settings:
This parameter is used to set the time constant when switching the smooth gain.
P2-29
GPE
Gain Switching Condition
Operation
Keypad/Software
Interface:
Default: 160000
Control
ALL
Mode:
Unit: pulse, Kpps, r/min
Range: 0 ~ 3840000
Data Size: 32-bit
Display
Decimal
Format:
Communication
Address: 023AH
023BH
Related Section: N/A
Settings:
This parameter is used to set the value of gain switching condition (pulse error, Kpps,
r/min) selected in P2-27. The setting value will be different depending on the different
gain switching condition.
7-60
Revision September 2013
ASDA-B2
P2-30■
Chapter 7 Servo Parameters
INH
Auxiliary Function
Operation
Keypad/Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: N/A
Range: -8 ~ +8
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 023CH
023DH
Related Section: N/A
Settings:
0: Disabled all functions described below.
1: Force the servo drive to be Servo On (upon software)
2~4: Reserved
5: After setting P2-30 to 5, the setting values of all parameters will lost (not remain in
the EEPROM) at power-down. When the parameters data are no more needed, using
this mode can allows users not to save parameters data into the EEPROM without
damaging the EEPROM. P2-30 should be set to 5 when using communication control
function.
Please note:
1. Please set P2-30 to 0 during normal operation.
2. The setting value of P2-30 will return to 0 automatically after re-power the servo
drive.
P2-31
AUT1
Speed Frequency Response Level in Auto and Address: 023EH
Semi-Auto Mode
023FH
Operation
Keypad/Software
Interface:
Default: 80
Control
ALL
Mode:
Unit: Hz
Range: 1 ~ 1000
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Related Section:
Section 5.6,
Section 6.3.6
Settings:
This parameter allows the users to set the speed frequency response level of
auto-tuning and semi-auto tuning mode. The speed frequency response settings are
as follows:
1 ~ 50Hz : Low stiffness and low frequency response
51 ~ 250Hz : Medium stiffness and medium frequency response
251 ~ 550Hz : High stiffness and high frequency response
Please note:
Revision September 2013
7-61
Chapter 7 Servo Parameters
ASDA-B2
1. The servo drive will set the position frequency response according to the setting
value of P2-31.
2. This parameter is activated by P2-32. Please refer to Section 5.6 for the tuning
procedure and the related settings.
P2-32▲
AUT2
Tuning Mode Selection
Operation
Keypad/Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 2
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 0240H
0241H
Related Section:
Section 5.6,
Section 6.3.6
Settings:
0: Manual mode
1: Auto Mode [Continuous adjustment]
2: Semi-Auto Mode [Non-continuous adjustment]
Explanation of manual mode:
1. When P2-32 is set to mode#0, the setting value of P2-00, P2-02, P2-04, P2-06,
P2-07, P2-25 and P2-26 can be user-defined. When switching mode #1 or #2 to
#0, the setting value of P2-00, P2-02, P2-04, P2-06, P2-07, P2-25 and P2-26 will
change to the value that measured in #1 auto-tuning mode or #2 semi-auto tuning
mode.
Explanation of auto-tuning mode:
The servo drive will continuously estimate the system inertia, save the measured load
inertia value automatically and memorized in P1-37 every 30 minutes by referring to
the frequency response settings of P2-31.
1. When switching mode #1 or #2 to #0, the servo drive will continuously estimate
the system inertia, save the measured load inertia value automatically and
memorized in P1-37. Then, set the corresponding parameters according to this
measured load inertia value.
2. When switching mode#0 or #1 to #2, enter the appropriate load inertia value in
P1-37.
3. When switching mode#1 to #0, the setting value of P2-00, P2-04 and P2-06 will
change to the value that measured in #1 auto-tuning mode.
Explanation of semi-auto tuning mode:
1. When switching mode #2 to #0, the setting value of P2-00, P2-04, P2-06, P2-25
and P2-26 will change to the value that measured in #1 auto-tuning mode.
2. After the system inertia becomes stable (The displau of P2-33 will show 1), it will
stop estimating the system inertia, save the measured load inertia value
automatically, and memorized in P1-37. However, when P2-32 is set to mode#1 or
#2, the servo drive will continuously perform the adjustment for a period of time.
3. When the value of the system inertia becomes over high, the display of P2-33 will
7-62
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
show 0 and the servo drive will start to adjust the load inertia value continuously.
P2-33▲
AUT3
Semi-Auto Mode Inertia Adjustment Selection
Operation
Keypad/Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 1
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0242H
0243H
Related Section: N/A
Settings:
When the setting value of A is set to 0 or display is 0, it indicates that the load inertia
estimation of semi-auto tuning mode has been executed but not been completed yet.
When the setting value of A is set to 1, it indicates that the load inertia estimation of
semi-auto tuning mode has been completed. The measured load inertia is memorized
in P1-37. If P2-33 is reset to 0, the servo drive will perform continuous adjustment for
estimating the load inertia (P1-37) again.
B: Reserved.
P2-34
SDEV
Overspeed Warning Condition
Operation
Keypad/Software
Interface:
Default: 5000
Control
S
Mode:
Unit: r/min
Range: 1 ~ 6000
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0244H
0245H
Related Section: N/A
Display Format: Decimal
Settings:
This parameter is used to set the over speed threshold that is used to determine the
over speed fault condition. When the difference in speed between the desired speed
and actual motor speed is over than the setting value of parameter P2-34, the servo
fault, Overspeed (AL007) will be activated.
Revision September 2013
7-63
Chapter 7 Servo Parameters
P2-35
PDEV
ASDA-B2
Excessive Error Warning Condition
Operation
Keypad/Software
Interface:
Default: 480000
Control
PT
Mode:
Unit: pulse
Range: 1 ~ 16000000
Data Size: 32-bit
Display
Decimal
Format:
Communication
Address: 0246H
0247H
Related Section: N/A
Settings:
This parameter is used to set the position deviation excessive error threshold that is
used to determine the escessive deviation fault condition. When the difference in
pulse number between the desired position and actual motor position is over than the
setting value of parameter P2-35, the servo fault, Excessive Deviation (AL009) will be
activated.
P2-36
DI9
External Digital Input Terminal 9 (DI9)
Operation
Keypad/Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 015Fh
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 0248H
0249H
Related Section:
Table 7.A
Settings:
The parameters from P2-36 to P2-41 are used to determine the functions and
statuses of external DI9 ~ DI14.
A: DI (Digital Input) Function Settings:
For the setting value of P2- 36 ~ P2-41, please refer to Table 7.A.
B: External DI (Digital Input) Enabled Status Settings:
0: Normally closed (contact b)
1: Normally open (contact a)
7-64
Revision September 2013
ASDA-B2
P2-37
Chapter 7 Servo Parameters
DO6
Digital Output Terminal 6 (DO6)
Operation
Keypad/Software
Interface:
Default: 7
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 013Fh
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 024AH
024BH
Related Section:
Table 7.B
Settings: Refer to P2-18 for explanation.
P2-38
Reserved (Do Not Use)
Address: 024CH
024DH
P2-39
Reserved (Do Not Use)
Address: 024EH
024FH
P2-40
Reserved (Do Not Use)
P2-41
Reserved (Do Not Use)
P2-42
Reserved (Do Not Use)
P2-43
NCF2
Address: 0250H
0251H
Address: 0252H
0253H
Address: 0254H
0255H
Notch Filter 2 (Resonance Suppression)
Operation
Keypad/Software
Interface:
Default: 1000
Control
ALL
Mode:
Unit: Hz
Range: 50 ~ 2000
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0256H
0257H
Related Section:
Section 6.3.7
Settings:
This parameter is used to set second resonance frequency of mechanical system. It
can be used to suppress the resonance of mechanical system and reduce the
vibration of mechanical system.
If P2-43 is set to 0, this parameter is disabled.
The parameters P2-23 and P2-24 are the first group of notch filter parameters and the
parameters P2-43 and P2-44 are the second group of notch filter parameters.
Revision September 2013
7-65
Chapter 7 Servo Parameters
P2-44
DPH2
ASDA-B2
Notch Filter Attenuation Rate 2
(Resonance Suppression)
Operation
Keypad/Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: dB
Range: 0 ~ 32
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0258H
0259H
Related Section:
Section 6.3.7
Settings:
This parameter is used to set magnitude of the resonance suppression that is set by
parameter P2-43. If P2-44 is set to 0, the parameters P2-43 and P2-44 are both
disabled.
P2-45
NCF3
Notch Filter 3 (Resonance Suppression)
Operation
Keypad/Software
Interface:
Default: 1000
Control
ALL
Mode:
Unit: Hz
Range: 50 ~ 2000
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 025AH
025BH
Related Section:
Section 6.3.7
Settings:
This parameter is used to set third resonance frequency of mechanical system. It can
be used to suppress the resonance of mechanical system and reduce the vibration of
mechanical system.
If P2-45 is set to 0, this parameter is disabled.
P2-46
DPH3
Notch Filter Attenuation Rate 3
(Resonance Suppression)
Operation
Keypad/Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: dB
Range: 0 ~ 32
Data Size: 16-bit
Display
Decimal
Format:
7-66
Communication
Address: 025CH
025DH
Related Section:
Section 6.3.7
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Settings:
This parameter is used to set magnitude of the resonance suppression that is set by
parameter P2-45. If P2-46 is set to 0, the parameters P2-45 and P2-46 are both
disabled.
P2-47
ANCF Auto Resonance Suppression Mode Selection
Operation
Keypad/Software
Interface:
Default: 1
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 2
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 025EH
025FH
Related Section: N/A
Settings:
0: Disable Auto Resonance Suppression Mode.
The setting value of P2-23~P2-24 and P2-43~P2-46 will be fixed and will not be
changed.
1: Auto Resonance Suppression Mode 1 [Non-continuous adjustment]
After the resonance is suppressed, the setting value of P2-23, P2-24, P2-43, P2-44,
P2-45 and P2-46 will be fixed and will not be changed.
2: Auto Resonance Suppression Mode 2 [Continuous adjustment]
The servo drive will perform the resonance suppression continuously (will not stop).
The setting value of P2-23, P2-24, P2-43, P2-44, P2-45 and P2-46 will not be
fixed.
When P2-47 is set to 1, the resonance suppression will be enabled automatically.
After the mechanical system becomes stable, the setting value of P2-47 will return to
0. When the mechanical system is stable, the resonance suppression point will be
memorized. When the mechanical system is not stable, if the servo drive is restarted
or P2-47 is set to 1, the servo drive will estimate the resonance suppression point
again.
When P2-47 is set to 2, the servo drive will perform the resonance suppression
continuously. When the mechanical system becomes stable, the resonance
suppression point will be memorized. When the mechanical system is not stable, if the
servo drive is restarted, the servo drive will estimate the resonance suppression point
again.
When switching the mode#1 or #2 to #0, the setting values of P2-43, P2-44, P2-45
and P2-46 will be saved automatically.
Revision September 2013
7-67
Chapter 7 Servo Parameters
P2-48
ASDA-B2
ANCL Auto Resonance Suppression Detection Level
Operation
Keypad/Software
Interface:
Default: 100
Control
ALL
Mode:
Unit: N/A
Range: 1 ~ 300%
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0260H
0261H
Related Section: N/A
Settings:
When the setting value is smaller, the system will become more sensitive to detect
and find the resonance.
When the value of ↑
The setting value of P2-48 ↑, the sensitivity of detecting resonance ↓.
The setting value of P2-48 ↓, the sensitivity of detecting resonance ↑.
P2-49
SJIT
Speed Detection Filter and Jitter Suppression
Operation
Keypad/Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: sec
Range: 0 ~ 1F
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0262H
0263H
Related Section:
Section 6.2.5
Settings:
7-68
Setting Value of P2-49
Cutoff Frequency of Speed Loop Feedback (Hz)
00
2500
01
2250
02
2100
03
2000
04
1800
05
1600
06
1500
07
1400
08
1300
09
1200
0A
1100
0B
1000
0C
950
Revision September 2013
ASDA-B2
P2-50
Chapter 7 Servo Parameters
Setting Value of P2-49
Cutoff Frequency of Speed Loop Feedback (Hz)
0D
900
0E
850
0F
800
10
750
11
700
12
650
13
600
14
550
15
500
16
450
17
400
18
350
19
300
1A
250
1B
200
1C
175
1D
150
1E
125
1F
100
DCLR Pulse Deviation Clear Mode
Operation
Keypad/Software
Interface:
Default: 00
Control
PT
Mode:
Unit: N/A
Range: 0 ~ 11
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 0264H
0265H
Related Section: N/A
Settings:
Triggering Method
Function Selection
Not used
For digital input function (DI function), please refer to Table 7.A.
This pulse deviation clear function is enabled when a digital input is set to pulse clear
function (CCLR mode, DI (Digital Input) setting value is 0x04). When this input is
triggered, the position accumulated pulse number will be clear to 0. (available in PT
mode only)
Revision September 2013
7-69
Chapter 7 Servo Parameters
ASDA-B2
Triggering Method Settings:
0: CCLR is triggered by rising-edge
1: CCLR is triggered bu level
Function Selection Settings:
0: Clear position accumulated pulse number
When this input is triggered, the position accumulated pulse number will be clear
to 0.
1: Clear feedback PUU
When this input is triggered, the feedback PUU will be clear to 0.
P2-51
Reserved (Do Not Use)
Address: 0266H
0267H
P2-52
Reserved (Do Not Use)
Address: 0268H
0269H
P2-53
KPI
Position Integral Compensation
Operation
Keypad/Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: rad/s
Range: 0 ~ 1023
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 026AH
026BH
Related Section:
Section 6.3.6
Settings:
This parameter is used to set the integral time of position loop. When the value of
position integral compensation is increased, it can decrease the position control
deviation. However, if the setting value is over high, it may generate position
overshoot or noise.
7-70
P2-54
Reserved (Do Not Use)
Address: 026CH
026DH
P2-55
Reserved (Do Not Use)
Address: 026EH
026FH
P2-56
Reserved (Do Not Use)
Address: 0270H
0271H
P2-57
Reserved (Do Not Use)
Address: 0272H
0273H
P2-58
Reserved (Do Not Use)
Address: 0274H
0275H
P2-59
Reserved (Do Not Use)
Address: 0276H
0277H
Revision September 2013
ASDA-B2
P2-60
Chapter 7 Servo Parameters
GR4
Electronic Gear Ratio (2nd Numerator) (N2)
Operation
Keypad/Software
Interface:
Default: 16
Control
PT
Mode:
Unit: pulse
Range: 1 ~ (226-1)
Data Size: 32-bit
Display
Decimal
Format:
Communication
Address: 0278H
0279H
Related Section: N/A
Settings:
The electronic gear numerator value can be set via GNUM0, GNUM1 (refer to Table
7.A).
When the GNUM0, GNUM1 are not defined, the default of gear numerator value is set
by P1-44.
When the users wish to set the gear numerator value by using GNUM0, GNUM1,
please set P2-60 ~ P2-62 after the servo motor has been stopped to prevent the
mechanical system vibration.
P2-61
GR5
Electronic Gear Ratio (3rd Numerator) (N3)
Operation
Keypad/Software
Interface:
Default: 16
Control
PT
Mode:
Unit: pulse
Range: 1 ~ (226-1)
Data Size: 32-bit
Display
Decimal
Format:
Communication
Address: 027AH
027BH
Related Section: N/A
Settings:
Refer to P2-60 for explanation.
Revision September 2013
7-71
Chapter 7 Servo Parameters
P2-62
ASDA-B2
Electronic Gear Ratio (4th Numerator) (N4)
GR6
Operation
Keypad/Software
Interface:
Default: 16
Control
PT
Mode:
Unit: pulse
Range: 1 ~ (226-1)
Data Size: 32-bit
Display
Decimal
Format:
Communication
Address: 027CH
027DH
Related Section: N/A
Settings:
Refer to P2-60 for explanation.
P2-63
Reserved (Do Not Use)
Address: 027EH
027FH
P2-64
Reserved (Do Not Use)
Address: 0280H
0281H
P2-65
GBIT
Special Function 1
Operation
Keypad/Software
Interface:
Default: 0
Control
PT, S
Mode:
Unit: N/A
Range: 0 ~ 0xFFFF
Data Size: N/A
Display
N/A
Format:
Communication
Address: 0282H
0283H
Related Section: N/A
Settings:
Bit15 Bit14 Bit13 Bit12 Bit11 Bit10 Bit9 Bit8 Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
Bit5
Bit4
Bit3
Bit2
Bit2 ~ Bit5: Reserved. Must be set to 0.
Bit6
Bit6: Abnormal pulse command detection
0: enable abnormal pulse command detection
1: disable abnormal pulse command detection
Bit8
Bit8: U, V, W wiring error detection
1: enable U, V, W wiring error detection
7-72
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Bit9
Bit9: U, V, W wiring cut-off detection
1: enable U, V, W wiring cut-off detection
Bit10
Bit10: DI ZCLAMP function selection
When the following conditions are all met, ZCLAMP function will be activated.
Condition1: Speed mode
Condition2: DI ZCLAMP is activated.
Condition3: External analog speed command or internal registers speed command is
less than parameter P1-38.
0: When the command source is an analog speed command, the users can use
ZCLAMP DI signal to stop the motor at the desire position and do not care the
acceleration and deceleration speed curve of the analog speed command. The
motor will be locked at the position when ZCLAMP conditions are satisfied.
0: When the command source is an internal speed command, the users can use
ZCLAMP DI signal to stop the motor at the desire position and keep the the
acceleration and deceleration speed curve of the internal speed command. The
motor will be locked at the position when ZCLAMP conditions are satisfied.
1: When the command source is an analog speed command, the users can use
ZCLAMP DI signal to stop the motor at the desire position and do not care the
acceleration and deceleration speed curve of the internal speed command. When
ZCLAMP conditions are satisfied, the speed command is decreased to 0 r/min.
When ZCLAMP conditions are not satisfied, the speed command will follow the
analog speed command through Accel/Decel S-curve.
Revision September 2013
7-73
Chapter 7 Servo Parameters
ASDA-B2
1: When the command source is an internal speed command, the users can use
ZCLAMP DI signal to stop the motor at the desire position and keep the
acceleration and deceleration speed curve of the analog speed command. When
ZCLAMP conditions are satisfied, the speed command is forced to 0 r/min directly.
B11
Bit11: NL(CWL)/PL(CCWL) pulse input inhibit function
0: Disable NL(CWL)/PL(CCWL) pulse input inhibit function. In PT mode, no matter
NL or PL exists or not, external position pulse command will be input into the
servo drive.
1: Enable NL(CWL)/PL(CCWL) pulse input inhibit function. In PT mode, if NL exists,
the external NL pulse input into the servo drive will be inhibited and PL pulse input
will be accepted. On the one hand, in PT mode, if PL exists, the external PL pulse
input into the servo drive will be inhibited and PL pulse input will be accepted.
Please note:
If NL and PL both exist, NL and PL pulse input into the servo drive will be both
inhibited.
7-74
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Bit12
Bit12: Input power phase loss detection function
0: Enable Input power phase loss (AL022) detection function
1: Disable Input power phase loss (AL022) detection function
Bit13
Bit13: Encoder output error detection function
0: Enable encoder output error (AL018) detection function
1: Disable encoder output error (AL018) detection function
Bit15
Bit14
Bit14 ~ Bit15: Reserved. Must be set to 0.
P2-66
GBIT2 Special Function 2
Operation
Keypad/Software
Interface:
Default: 0
Control
PT, S
Mode:
Unit: N/A
Range: 0 ~ 0xFFFF
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 0284H
0285H
Related Section: N/A
Settings:
Bit7 Bit6 Bit5 Bit4 Bit3 Bit2 Bit1 Bit0
Bit0
Bit0: Speed limit accel / decel function
The torque command source is determined by TCM0 and TCM1. When the digital
input, TQP or TQN is used, the torque command is activated by TQP or TQN. When
TQP is ON, the torque will be output directly as the same as the command souce.
For example, when TQP is ON, if the torque command source is an input voltage of
5V and P1-41 is set to 100, it indicates that the torque command is 50% rated torque
until the speed is limited. However, whenTQN is ON, if the torque command source
is an input voltage of 5V and P1-41 is set to 100, it indicates that the torque
command is -50% rated torque until the speed is limited.
Speed limit function can be enabled always by P1-02. When P1-02 is set to 0x10, the
speed limit function can be enabled all the time and the users do not need to use DI,
SPDLM to switch the speed limit function.
The speed limit command is determined by SPD0 and SPD1. The acceleration and
deceleration time is determined by P1-34, P1-35 and P1-36.
Revision September 2013
7-75
Chapter 7 Servo Parameters
TQP
(DI Code:
0x48)
ON
ON
OFF
OFF
ASDA-B2
TQN
(DI Code:
Torque Output
0x49)
ON
Zero torque output
Output the torque of the command source directly
OFF
(do not reverse the command, and output the torque
directly)
Reverse
the torque of the command source
ON
(reverse the command first, and then output the torque)
OFF
Zero torque output
The timing charts of speed limit profile (with accel / decel function)and torque command
(TQP/TQN):
Bit1
Bit1: Reserved. Must be set to 0.
Bit2
Bit2: Undervoltage (Servo Drive Fault, AL003) clear mode selection
0: The fault, Undervoltage will not be cleared automatically.
1: The fault, Undervoltage will be cleared automatically.
Bit6
Bit5
Bit4
Bit3
Bit3 ~ Bit6: Reserved. Must be set to 0.
Bit7
Bit7: Motor temperature warning (Servo Drive Fault, AL067) display mode
selection
0: The fault, Undervoltage will be displayed.
1: The fault, Undervoltage will not be displayed.
7-76
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Bit9
Bit9:
0: Alarm output (DO function 0x11)
1: Error output (DO function 0x07)
P2-67
JSL
Stable Inertia Estimating Time
Operation
Keypad/Software
Interface:
Default: 1.5
Control
ALL
Mode:
Unit: 1 times
Range: 0 ~ 200.0
Data Size: 16-bit
Display
One-digit
Format:
Input Value
1.5 = 1.5 times
Example:
Communication
Address: 0286H
0287H
Related Section: N/A
15
0.1 times
0 ~ 2000
Decimal
15 = 1.5 times
Settings:
In semi-auto tuning mode, after the servo drive continuously perform the adjustment
for a period of time which is determined by P2-67, the system will consider that the
system inertia has become stable and finish the operation of system inertia
estimation.
Revision September 2013
7-77
Chapter 7 Servo Parameters
Group 3: P3-xx
P3-00●
ASDA-B2
Communication Parameters
ADR
Communication Address Setting
Operation
Keypad / Software
Interface:
Default: 0x7F
Control
ALL
Mode:
Unit: N/A
Range: 0x01 ~ 0x7F
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 0300H
0301H
Related Section:
Section 8.2
Settings:
This parameter is used to set the communication slave address in hexadecimal
format.
Display
0
0
Y
X
Range
-
-
0~7
0~F
X: Axis number which indicates the value must be within the range from 0 through F.
Y: Group number which indicates the value must be within the range from 0 to through
7
When using RS-232/485 communication, this parameter is used set the
communication address in hexadecimal format. If the AC servo drive is controlled by
RS-232/485 communication, each drive (or device) must be uniquely identified. One
servo drive only can set one address. If the address is duplicated, there will be a
communication fault. This address is an absolute address which represents the servo
drive on a RS-232/485 network.
Please note:
1. When the address of host (external) controller is set to 0xFF, it is with
auto-respond function. Then, the servo drive will receive from and respond to host
(external) controller both no matter the address is matching or not. However, the
parameter P3-00 cannot be set to 0xFF.
P3-01
BRT
Transmission Speed
Operation
Keypad / Software
Interface:
Default: 0x0033
Control
ALL
Mode:
Unit: bps
Range: 0x0000 ~ 0x0055
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 0302H
0303H
Related Section:
Section 8.2
Settings:
This parameter is used to set the baud rate and data transmission speed of the
7-78
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
communications.
0
Z
Y
X
COM Port
-
-
RS-485
RS-232
Range
0
0
0~5
0~5
Settings:
0: Baud rate 4800 (data transmission speed: bits / second)
1: Baud rate 9600 (data transmission speed: bits / second)
2: Baud rate 19200 (data transmission speed: bits / second)
3: Baud rate 38400 (data transmission speed: bits / second)
4: Baud rate 57600 (data transmission speed: bits / second)
5: Baud rate 115200 (data transmission speed: bits / second)
P3-02
PTL
Address: 0304H
0305H
Related Section:
Section 8.2
Communication Protocol
Operation
Keypad / Software
Interface:
Default: 0x0066
Control
ALL
Mode:
Unit: N/A
Range: 0x0000 ~ 0x0088
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Settings:
This parameter is used to set the communication protocol. The alphanumeric
characters represent the following: 7 or 8 is the number of data bits; N, E or O refers
to the parity bit, Non, Even or Odd; the 1 or 2 is the numbers of stop bits.
0
Z
Y
X
COM Port
-
-
RS-485
RS-232
Range
0
0
0~8
0~8
0: Modbus ASCII mode, <7,N,2>
1: Modbus ASCII mode, <7,E,1>
2: Modbus ASCII mode, <7,O,1>
3: Modbus ASCII mode, <8,N,2>
4: Modbus ASCII mode, <8,E,1>
5: Modbus ASCII mode, <8,O,1>
6: Modbus RTU mode, <8,N,2>
7: Modbus RTU mode, <8,E,1>
8: Modbus RTU mode, <8,O,1>
Revision September 2013
7-79
Chapter 7 Servo Parameters
P3-03
FLT
ASDA-B2
Transmission Fault Treatment
Operation
Keypad / Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 1
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 0306H
0307H
Related Section:
Section 8.2
Settings:
0: Display fault and continue operating
1: Display fault and decelerate to stop operating
This parameter is used to determine the operating sequence once a communication
fault has been detected. If '1' is selected, the drive will stop operating upon detection
the communication fault. The mode of stopping is set by parameter P1-32.
P3-04
CWD
Communication Time Out Detection
Operation
Keypad / Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: sec
Range: 0 ~ 20
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0308H
0309H
Related Section:
Section 8.2
Settings:
This parameter is used to set the maximum permissible time before detecting a fault
due to communication time out. When P3-04 is set to a value over than 0, it indicates
this parameter is enabled. However, if not communicating with the servo in this period
of time, the servo drive will assume the communication has failed and show the
communication error fault message.
When P3-04 is set to 0, this parameter is disabled.
P3-05
CMM
Communication Selection
Operation
Keypad / Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: N/A
Range: 0x00 ~ 0x01
Data Size: 16-bit
7-80
Communication
Address: 030AH
030BH
Related Section:
Section 8.2
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Display
Hexadecimal
Format:
Settings:
RS-232 Communication interface selection
0: RS-232 via Modbus communication
1: RS-232 upon ASDA-Soft software
P3-06■
SDI
Digital Input Communication Function
Operation
Keypad / Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: N/A
Range: 0x0000 ~ 0x1FFF
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 030CH
030DH
Related Section:
Section 8.2
Settings:
The setting of this parameter determines how the Digital Inputs (DI) accept commands
and signals.
Bit0 ~ Bit 8 corresponds with DI1 ~ DI9. The least significant bit (Bit0) shows DI1
status and the most significant bit (Bit7) shows DI8 status.
Bit settings:
0: Digital input is controlled by external command (via CN1)
1: Digital input is controlled by parameter P4-07
For the settings of DI1 ~ DI9, please refer to P2-10 ~ P2-17 and P2-36.
This parameter P3-06 also works in conjunction with the parameter P4-07 which has
several functions. Please see section 8.2 for details.
P3-07
CDT
Communication Response Delay Time
Operation
Keypad / Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: 1ms
Range: 0 ~ 1000
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 030EH
030FH
Related Section:
Section 8.2
Settings:
This parameter is used to delay the communication time that servo drive responds to
host controller (external controller).
Revision September 2013
7-81
Chapter 7 Servo Parameters
P3-08■
MNS
ASDA-B2
Monitor Mode
Operation
Keypad / Software
Communication
Interface:
Default: 0000
Control
ALL
Mode:
Unit: N/A
Range: refer to the description of Settings
Data Size: 16-bit
Display
Hexadecimal
Format:
Address: 0310H
0311H
Related Section:
Section 8.2
Settings:
This parameter is used to monitor the data of the servo drive via communication. The
monitor data can be displayed on PC upon the data scope function provided by
ASDA-Soft software.
Word
-
-
Function
-
-
Range
0
0
Low
High
Monitor mode
0
0~3
H: Monitor mode, the value must be within the range from 0 through 3.
0: Disabled, i.e. disable monitor function.
1: Reserved.
2: High-speed monitor mode. The sampling time is 2000 times per second and 4
channels can be monitored.
3: High-speed monitor mode. The sampling time is 4000 times per second and 2
channels can be monitored.
7-82
P3-09
Reserved (Do Not Use)
Address: 0312H
0313H
P3-10
Reserved (Do Not Use)
Address: 0314H
0315H
P3-11
Reserved (Do Not Use)
Address: 0316H
0317H
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Group 4: P4-xx
P4-00★
Diagnosis Parameters
ASH1
Fault Record (N)
Operation
Keypad / Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: N/A
Range: N/A
Data Size: 32-bit
Display
Hexadecimal
Format:
Communication
Address: 0400H
0401H
Related Section:
Section 4.4.1
Settings:
This parameter is used to set the most recent fault record.
Display of Low Word: LXXXX: It indicates the fault code, i.e. alarm code
Display of High Word: hYYYY: Reserved.
P4-01★
ASH2
Fault Record (N-1)
Operation
Keypad / Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: N/A
Range: N/A
Data Size: 32-bit
Display
Hexadecimal
Format:
Communication
Address: 0402H
0403H
Related Section:
Section 4.4.1
Settings:
This parameter is used to set the second most recent fault record.
Display of Low Word: LXXXX: It indicates the fault code, i.e. alarm code.
Display of High Word: hYYYY: It indicates the CANopen error code.
P4-02★
ASH3
Fault Record (N-2)
Operation
Keypad / Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: N/A
Range: N/A
Data Size: 32-bit
Display
Hexadecimal
Format:
Communication
Address: 0404H
0405H
Related Section:
Section 4.4.1
Settings:
This parameter is used to set the third most recent fault record.
Revision September 2013
7-83
Chapter 7 Servo Parameters
ASDA-B2
Display of Low Word: LXXXX: It indicates the fault code, i.e. alarm code.
Display of High Word: hYYYY: It indicates the CANopen error code.
P4-03★
ASH4
Fault Record (N-3)
Operation
Keypad / Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: N/A
Range: N/A
Data Size: 32-bit
Display
Hexadecimal
Format:
Communication
Address: 0406H
0407H
Related Section:
Section 4.4.1
Settings:
This parameter is used to set the fourth most recent fault record.
Display of Low Word: LXXXX: It indicates the fault code, i.e. alarm code.
Display of High Word: hYYYY: It indicates the CANopen error code.
P4-04★
ASH5
Fault Record (N-4)
Operation
Keypad / Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: N/A
Range: N/A
Data Size: 32-bit
Display
Hexadecimal
Format:
Communication
Address: 0408H
0409H
Related Section:
Section 4.4.1
Settings:
This parameter is used to set the fifth most recent fault record.
Display of Low Word: LXXXX: It indicates the fault code, i.e. alarm code.
Display of High Word: hYYYY: It indicates the CANopen error code.
P4-05
JOG
JOG Operation
Operation
Keypad / Software
Interface:
Default: 20
Control
ALL
Mode:
Unit: r/min
Range: 0 ~ 5000
Data Size: 16-bit
Display
Decimal
Format:
7-84
Communication
Address: 040AH
040BH
Related Section:
Section 4.4.2
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Settings:
JOG operation command:
1. Operation Test
(1) Press the SET key to display the JOG speed. (The default value is 20 r/min).
(2) Press the UP or DOWN arrow keys to increase or decrease the desired JOG
speed. (This also can be undertaken by using the SHIFT key to move the
cursor to the desired unit column (the effected number will flash) then changed
using the UP and DOWN arrow keys).
(3) Press the SET when the desired JOG speed is displayed. The Servo Drive will
display "JOG".
(4) Press the UP or DOWN arrow keys to jog the motor either P(CCW) or N(CW)
direction. The motor will only rotation while the arrow key is activated.
(5) To change JOG speed again, press the MODE key. The servo Drive will display
"P4 - 05". Press the SET key and the JOG speed will displayed again. Refer
back to #(2) and #(3) to change speed.
(6) In JOG operation mode, if any fault occurs, the motor will stop running. The
maximum JOG speed is the rated speed of the servo motor.
2. DI Signal Control
Set the value of DI signal as JOGU and JOGD (refer to Table 7.A).
Users can perform JOG run forward and run reverse control.
3. Communication Control
To perform a JOG Operation via communication command, use communication
addresses 040AH and 040BH.
(1) Enter 1 ~ 5000 for the desired JOG speed
(2) Enter 4998 to JOG in the P(CCW) direction
(3) Enter 4999 to JOG in the N(CW) direction
(4) Enter 0 to stop the JOG operation
Please note that when using communication control, please set P2-30 to 5 to avoid
that there are excessive writes to the system flash memory.
P4-06
▲■
FOT
Digital Output Register (Readable and
Writable)
Operation
Keypad / Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: Range: 0 ~ 0x3F
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 040CH
040DH
Related Section:
Section 4.4.3
Settings: Contact control of the force output
0: Non-force output (When the communication sets to 0, it can cancel
Revision September 2013
7-85
Chapter 7 Servo Parameters
ASDA-B2
the force output function.)
P4-07■
ITST
Input Status
Operation Software (cannot read
Interface: and write throught the Communication
panel)
Default: 0
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 01FF
Data Size: 16-bit
Display
Hexadecimal
Format:
Address: 040CH
040DH
Related Section:
Section 4.4.4
Section 8.2
Settings:
The control of digital inputs can be determined by the external terminals (DI1 ~ DI9) or
by the internal software digital inputs SDI1 ~ SDI9 (corresponds to Bit0 ~ Bit8 of P1-47)
via communication (upon software). Please refer to P3-06 and section 8.2 for the
setting method.
P3-06
External DIs
Read or Write
Final DI Status
Internal DIs
Read P4-07: Display the final status of DI input signal.
Write P4-07: Write the status of software digital inputs SDI1 ~ SDI9
(No matter the servo drive is controller through digital keypad or communication
control, the function of this parameter is the same.)
For example:
External Control: Display the final status of DI input signal
When the read value of P4-07 is 0x0011, it indicates that DI1 and DI5 are ON.
Communication Control (Internal DIs): Read the status of input signal (upon software).
For example:
When the write value of P4-07 is 0x0011, it indicates that software digital inputs SDI1
and SDI5 are ON.
Bit0 ~ Bit8 corresponds with DI1 ~ DI9.
For the settings of DI1 ~ DI9, please refer to P2-10 ~ P2-17 and P2-36.
P4-08★
PKEY
Digital Keypad Input of Servo Drive
Operation
Keypad / Software
Interface:
Default: N/A
Control
ALL
Mode:
7-86
Communication
Address: 0410H
0411H
Related Section: N/A
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Unit: N/A
Range: Read only
Data Size: 16-bit
Display
Hexadecimal
Format:
Settings:
This parameter is used to check if MODE, UP, DOWN, SHIFT, and SET keys on the
drive keypad being pressed or not. It is used to examine if these five keys work
normally via communication during production.
P4-09★
MOT
Output Status (Read-only)
Operation
Keypad / Software
Interface:
Default: N/A
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 0x3F
Data Size: 16-bit
Display
Hexadecimal
Format:
Communication
Address: 0412H
0413H
Related Section:
Section 4.4.5
Settings:
There is no difference when reading DO output signal via the drive keypad or the
communication.
P4-10■
CEN
Adjustment Function
Operation
Keypad / Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 6
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0414H
0415H
Related Section: N/A
Settings:
0: Reserved
1: Execute analog speed input drift adjustment
2: Execute analog torque input drift adjustment
3: Execute current detector (V phase) drift adjustment
4: Execute current detector (W phase) drift adjustment
5: Execute drift adjustment of the above 1~4
6: Execute IGBT NTC calibration
Please note:
Revision September 2013
7-87
Chapter 7 Servo Parameters
ASDA-B2
1. This adjustment function is enabled after parameter P2-08 is set to 20.
2. When executing any adjustment, the external wiring connected to analog speed or
torque must be removed and the servo system should be off (Servo off).
P4-11
SOF1
Analog Speed Input Drift Adjustment 1
Operation
Keypad / Software
Interface:
Default: Factory setting
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 32767
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0416H
0417H
Related Section: N/A
Settings:
The adjustment functions from P4-11 through P4-19 are enabled after parameter
P2-08 is set to 22. Although these parameters allow the users to execute manual
adjustment, we still do not recommend the users to change the default setting value of
these parameters (P4-11 ~ P4-19) manually.
Please note that when P2-08 is set to 10, the users cannot reset this parameter.
P4-12
SOF2
Analog Speed Input Drift Adjustment 2
Operation
Keypad / Software
Interface:
Default: Factory setting
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 32767
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0418H
0419H
Related Section: N/A
Settings:
Refer to P4-11 for explanation.
Please note that when P2-08 is set to 10, the users cannot reset this parameter.
P4-13
TOF1
Analog Torque Drift Adjustment 1
Operation
Keypad / Software
Interface:
Default: Factory setting
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 32767
Data Size: 16-bit
7-88
Communication
Address: 041AH
041BH
Related Section: N/A
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Display
Decimal
Format:
Settings:
Refer to P4-11 for explanation.
Please note that when P2-08 is set to 10, the users cannot reset this parameter.
P4-14
TOF2
Analog Torque Drift Adjustment 2
Operation
Keypad / Software
Interface:
Default: Factory setting
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 32767
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 041CH
041DH
Related Section: N/A
Settings:
Refer to P4-11 for explanation.
Please note that when P2-08 is set to 10, the users cannot reset this parameter.
P4-15
COF1
Current Detector Drift Adjustment (V1 phase)
Operation
Keypad / Software
Interface:
Default: Factory setting
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 32767
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 041EH
041FH
Related Section: N/A
Settings:
Refer to P4-11 for explanation.
Please note that when P2-08 is set to 10, the users cannot reset this parameter.
P4-16
COF2
Current Detector Drift Adjustment (V2 phase)
Operation
Keypad / Software
Interface:
Default: Factory setting
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 32767
Data Size: 16-bit
Revision September 2013
Communication
Address: 0420H
0421H
Related Section: N/A
7-89
Chapter 7 Servo Parameters
ASDA-B2
Display
Decimal
Format:
Settings:
Refer to P4-11 for explanation.
Please note that when P2-08 is set to 10, the users cannot reset this parameter.
P4-17
COF3
Current Detector Drift Adjustment (W1 phase)
Operation
Keypad / Software
Interface:
Default: Factory setting
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 32767
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0422H
0423H
Related Section: N/A
Settings:
Refer to P4-11 for explanation.
Please note that when P2-08 is set to 10, the users cannot reset this parameter.
P4-18
COF4
Current Detector Drift Adjustment (W2 phase)
Operation
Keypad / Software
Interface:
Default: Factory setting
Control
ALL
Mode:
Unit: N/A
Range: 0 ~ 32767
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0424H
0425H
Related Section: N/A
Settings:
Refer to P4-11 for explanation.
Please note that when P2-08 is set to 10, the users cannot reset this parameter.
P4-19
TIGB
IGBT NTC Calibration
Operation
Keypad / Software
Interface:
Default: Factory setting
Control
ALL
Mode:
Unit: N/A
Range: 1 ~ 3
Data Size: 16-bit
7-90
Communication
Address: 0426H
0427H
Related Section: N/A
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Display
Decimal
Format:
Settings:
Refer to P4-11 for explanation.
o
When executing this auto adjustment, please ensure to cool the servo drive to 25 C.
P4-20
DOF1
Analog Monitor Output Drift Adjustment
(MON1)
Operation
Keypad / Software
Interface:
Default: Factory setting
Control
ALL
Mode:
Unit: mV
Range: -800 ~ 800
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0428H
0429H
Related Section:
Section 6.4.4
Settings:
Please note that when P2-08 is set to 10, the users cannot reset this parameter.
P4-21
DOF2
Analog Monitor Output Drift Adjustment
(MON2)
Operation
Keypad / Software
Interface:
Default: 0
Control
ALL
Mode:
Unit: mV
Range: -800 ~ 800
Data Size: 16-bit
Display
Decimal
Format:
Settings:
Communication
Address: 042AH
042BH
Related Section:
Section 6.4.4
Please note that when P2-08 is set to 10, the users cannot reset this parameter.
P4-22
SAO
Analog Speed Input Offset
Operation
Keypad / Software
Interface:
Default: 0
Control
S
Mode:
Unit: mV
Range: -5000 ~ 5000
Data Size: 16-bit
Display
Decimal
Format:
Revision September 2013
Communication
Address: 042CH
042DH
Related Section: N/A
7-91
Chapter 7 Servo Parameters
ASDA-B2
Settings:
In speed mode, the users can use this parameter to add an offset value to analog
speed input.
P4-23
TAO
Analog Torque Input Offset
Operation
Keypad / Software
Interface:
Default: 0
Control
T
Mode:
Unit: mV
Range: -5000 ~ 5000
Data Size: 16-bit
Display
Decimal
Format:
Settings:
Communication
Address: 042EH
042FH
Related Section: N/A
In speed mode, the users can use this parameter to add an offset value to analog
speed input.
P4-24
LVL
Undervoltage Error Level
Operation
Keypad / Software
Interface:
Default: 160
Control
ALL
Mode:
Unit: V (rms)
Range: 140 ~ 190
Data Size: 16-bit
Display
Decimal
Format:
Communication
Address: 0430H
0431H
Related Section: N/A
Settings:
When DC Bus voltage is lower than the value of P4-24 x 2 , the fault, Undervoltage
will occur.
7-92
Revision September 2013
ASDA-B2
Table 7.1
Chapter 7 Servo Parameters
Input Function Definition (DI)
Setting value: 0x01
DI Name
SON
DI Function Description
Servo On. When this DI is activated, it indicates the servo
drive is enabled.
Trigger
Control
Method
Mode
Level
Triggered
All
Setting value: 0x02
DI Name
DI Function Description
Trigger
Control
Method
Mode
A number of Faults (Alarms) can be cleared by activating
ARST. Please see table 10-3 for applicable faults that can
ARST
be cleared with the ARST command. However, please
investigate Fault or Alarm if it does not clear or the fault
Rising-edge
Triggered
All
description warrants closer inspection of the drive system.
Setting value: 0x03
DI Name
DI Function Description
Gain switching in speed and position mode. When GAINUP
GAINUP
is activated (P2-27 is set to 1), the gain is switched to the
gain multiplied by gain switching rate.
Trigger
Control
Method
Mode
Level
Triggered
PT S
Setting value: 0x04
DI Name
DI Function Description
When CCLR is activated, the setting parameter P2-50
CCLR
Pulse Clear Mode is executed.
0: After CCLR is activated (ON), the position accumulated
pulse number will be cleared continuously.
Trigger
Control
Method
Mode
Rising-edge
Triggered,
Level
PT
Triggered
Setting value: 0x05
DI Name
DI Function Description
When this signal is On and the motor speed value is lower
ZCLAMP than the setting value of P1-38, it is used to lock the motor in
the instant position while ZCLAMP is On.
Revision September 2013
Trigger
Control
Method
Mode
Level
Triggered
S
7-93
Chapter 7 Servo Parameters
ASDA-B2
Speed
Command
Setting value of
P1-38 (Zero speed)
ZCLAMP
input signal
OFF
ON
Motor Speed
Setting value of
P1-38 (Zero speed)
Time
Setting value: 0x06
DI Name
DI Function Description
Command input reverse control. When the drive is in the
CMDINV
Position, Speed and Torque mode, and CMDINV is
activated, the motor is in reverse rotation.
Trigger
Control
Method
Mode
Level
Triggered
S, T
Setting value: 0x07
DI Name
DI Function Description
Trigger
Control
Method
Mode
Trigger
Control
Method
Mode
Reserved
Setting value: 0x09
DI Name
DI Function Description
Torque limit enabled. When the drive is in speed and
TRQLM
position mode, and TRQLM is activated, it indicates the
Level
torque limit command is valid. The torque limit command
Triggered
PT, S
source is internal parameter or analog voltage.
Setting value: 0x10
DI Name
DI Function Description
Trigger
Control
Method
Mode
Speed limit enabled. When the drive is in torque mode and
SPDLM
SPDLM is activated, it indicates the speed limit command is
valid. The speed limit command source is internal
Level
Triggered
T
parameter or analog voltage.
7-94
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Setting value: 0x14 ~ 0x15
DI
DI Function Description
Name
Mode
Speed command selection 0 ~ 1 (Command S1 ~ S4)
DI signal of
Command
Command
CN1
Content
Range
No.
Source
SPD1 SPD0
Voltage
External
between
+/-10 V
S analog
V-REF and
command
SPD0
GND
S1
OFF OFF
Speed
SPD1
Sz None
command
0
is 0
S2
OFF ON
P1-09
-60000
S3
ON OFF
P1-10
Internal
~
parameter
+60000
S4
ON ON
P1-11
r/min
Trigger
Control
Method
Mode
Level
Triggered
S
Setting value: 0x16 ~ 0x17
DI
DI Function Description
Name
Mode
Torque command selection 0 ~ 1 (Command T1 ~ T4)
DI signal of
Command
Command
CN1
Content
No.
Source
TCM1 TCM0
Voltage
Analog
between
T
command V-REF
TCM0
and GND
T1
OFF OFF
TCM1
Torque
Tz None
command
is 0
P1-12
T2
OFF ON
Internal
T3
ON OFF
P1-13
parameter
T4
ON
ON
P1-14
Trigger
Control
Method
Mode
Range
+/-10 V
Level
Triggered
T
0
-300 ~
+300 %
Setting value: 0x18
DI Name
S-P
DI Function Description
Speed / Position mode switching.
OFF: Speed mode, ON: Position mode
Revision September 2013
Trigger
Control
Method
Mode
Level
Triggered
P, S
7-95
Chapter 7 Servo Parameters
ASDA-B2
Setting value: 0x19
DI Name
S-T
DI Function Description
Speed / Torque mode switching.
OFF: Speed mode, ON: Torque mode
Trigger
Control
Method
Mode
Level
Triggered
S, T
Setting value: 0x20
DI Name
T-P
DI Function Description
Torque / Position mode switching.
OFF: Torque mode, ON: Position mode
Trigger
Control
Method
Mode
Level
Triggered
P, T
Setting value: 0x21
DI Name
EMGS
DI Function Description
Emergency stop. It should be contact “b” and normally ON
or a fault (AL013) will display.
Trigger
Control
Method
Mode
Level
Triggered
All
Setting value: 0x22
DI Name
NL(CWL)
DI Function Description
Reverse inhibit limit. It should be contact “b” and normally
ON or a fault (AL014) will display.
Trigger
Control
Method
Mode
Level
Triggered
All
Setting value: 0x23
DI Name
PL(CCWL)
DI Function Description
Forward inhibit limit. It should be contact “b” and normally
ON or a fault (AL015) will display.
Trigger
Control
Method
Mode
Level
Triggered
All
Setting value: 0x25
DI Name
TLLM
7-96
DI Function Description
Torque limit - Reverse operation (Torque limit function is
valid only when P1-02 is enabled)
Trigger
Control
Method
Mode
Level
Triggered
PT, S
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Setting value: 0x26
DI Name
TRLM
DI Function Description
Torque limit - Forward operation (Torque limit function is
valid only when P1-02 is enabled)
Trigger
Control
Method
Mode
Level
Triggered
PT, S
Setting value: 0x37
DI Name
JOGU
DI Function Description
Forward JOG input. When JOGU is activated, the motor will
JOG in forward direction. [see P4-05]
Trigger
Control
Method
Mode
Level
Triggered
All
Setting value: 0x38
DI Name
JOGD
DI Function Description
Reverse JOG input. When JOGD is activated, the motor will
JOG in reverse direction. [see P4-05]
Trigger
Control
Method
Mode
Level
Triggered
All
Setting value: 0x43, 0x44
DI Name
DI Function Description
Trigger
Control
Method
Mode
Electronic gear ratio (Numerator) selection 0 ~ 1 [see P2-60
~ P2-62]
GNUM0
Level
GNUM1
Triggered
PT
Setting value: 0x45
DI Name
DI Function Description
Pulse inhibit input. When the drive is in position mode, if
INHP
INHP is activated, the external pulse input command is not
valid.
Revision September 2013
Trigger
Control
Method
Mode
Level
Triggered
PT
7-97
Chapter 7 Servo Parameters
ASDA-B2
Setting value: 0x48
DI Name
TQP
DI Function Description
Torque command source. Please refer to the settings of
P2-66 Bit0.
Trigger
Control
Method
Mode
Level
Triggered
T
Setting value: 0x49
DI Name
TQN
DI Function Description
Torque command source. Please refer to the settings of
P2-66 Bit0.
Trigger
Control
Method
Mode
Level
Triggered
T
NOTE
1) 11 ~ 17: Single control mode, 18 ~ 20: Dual control mode
2) When P2-10 to P2-17 and P2-36 is set to 0, it indicates input function is disabled.
7-98
Revision September 2013
ASDA-B2
Table 7.2
Chapter 7 Servo Parameters
Output Function Definition (DO)
Setting value: 0x01
DO Name
DO Function Description
Servo ready. SRDY is activated when the servo drive is
SRDY
ready to run. All fault and alarm conditions, if present, have
been cleared.
Trigger
Control
Method
Mode
Level
Triggered
All
Setting value: 0x02
DO Name
DO Function Description
Trigger
Control
Method
Mode
SON is activated when control power is applied the servo
drive. The drive may or may not be ready to run as a fault /
alarm condition may exist.
SON
Servo ON (SON) is "ON" with control power applied to the
servo drive, there may be a fault condition or not. The servo
Level
Triggered
All
is not ready to run. Servo ready (SRDY) is "ON" where the
servo is ready to run, NO fault / alarm exists.
Setting value: 0x03
DO Name
DO Function Description
Trigger
Control
Method
Mode
ZSPD is activated when the drive senses the motor is equal
to or below the Zero Speed Range setting as defined in
parameter P1-38.
ZSPD
For Example, at factory default ZSPD will be activated
when the drive detects the motor rotating at speed at or
Level
Triggered
All
below 10 r/min, ZSPD will remain activated until the motor
speed increases above 10 r/min.
Setting value: 0x04
DO Name
DO Function Description
Trigger
Control
Method
Mode
TSPD is activated once the drive has detected the motor
TSPD
has reached the Target Rotation Speed setting as defined
in parameter P1-39. TSPD will remain activated until the
Level
Triggered
All
motor speed drops below the Target Rotation Speed.
Revision September 2013
7-99
Chapter 7 Servo Parameters
ASDA-B2
Setting value: 0x05
DO Name
DO Function Description
When the drive is in PT mode, TPOS will be activated when
TPOS
the position error is equal and below the setting value of
P1-54.
Trigger
Control
Method
Mode
Level
Triggered
PT
Setting value: 0x06
DO Name
DO Function Description
TQL is activated when the drive has detected that the motor
TQL
has reached the torques limits set by either the parameters
P1-12 ~ P1-14 of via an external analog voltage.
Trigger
Control
Method
Mode
Level
Triggered
All,
except T,
Tz
Setting value: 0x07
DO Name
DO Function Description
Trigger
Control
Method
Mode
ALRM is activated when the drive has detected a fault
ALRM
condition. (However, when Reverse limit error, Forward limit
error, Emergency stop, Serial communication error, and
Level
Triggered
All
Undervoltage these fault occur, WARN is activated first.)
Setting value: 0x08
DO Name
DO Function Description
Trigger
Control
Method
Mode
Electromagnetic brake control. BRKR is activated (Actuation
of motor brake). (Please refer to parameters P1-42 ~ P1-43)
BRKR
7-100
Level
Triggered
All
Revision September 2013
ASDA-B2
Chapter 7 Servo Parameters
Setting value: 0x10
DO Name
DO Function Description
Trigger
Control
Method
Mode
Output overload warning. OLW is activated when the servo
drive has detected that the motor has reached the output
overload time set by parameter P1-56.
tOL = Permissible Time for Overload x setting value of P1-56
When overload accumulated time (continuously overload
time) exceeds the value of tOL, the overload warning signal
will output, i.e. DO signal, OLW will be ON. However, if the
accumulated overload time (continuous overload time)
exceeds the permissible time for overload, the overload
alarm (AL006) will occur.
For example:
If the setting value of parameter P1-56 (Output Overload
OLW
Warning Time) is 60%, when the permissible time for
overload exceeds 8 seconds at 200% rated output, the
Level
Triggered
All
overload fault (AL006) will be detected and shown on the
LED display.
At this time, tOL = 8 x 60% = 4.8 seconds
Result:
When the drive output is at 200% rated output and the drive
is continuously overloaded for 4.8 seconds, the overload
warning signal will be ON (DO code is 0x10, i.e. DO signal
OLW will be activated). If the drive is continuously
overloaded for 8 seconds, the overload alarm will be
detected and shown on the LED display (AL006). Then,
Servo Fault signal will be ON (DO signal ALRM will be
activated).
Setting value: 0x11
DO Name
DO Function Description
Trigger
Control
Method
Mode
Servo warning activated. WARN is activated when the drive
WARN
has detected Reverse limit error. Forward limit error,
Emergency stop, Serial communication error, and
Level
Triggered
All
Undervoltage these fault conditions.
Revision September 2013
7-101
Chapter 7 Servo Parameters
ASDA-B2
Setting value: 0x13
DO Name
DO Function Description
Trigger
Control
Method
Mode
SNL
Reverse software limit. SNL is activated when the servo
Level
(SCWL)
drive has detected that reverse software limit is reached.
Triggered
All
Setting value: 0x14
DO Name
DO Function Description
SPL
Forward software limit. SPL is activated when the servo drive
(SCCWL)
has detected that forward software limit is reached.
Trigger
Control
Method
Mode
Level
Triggered
All
Setting value: 0x19
DO Name
SP_OK
DO Function Description
Trigger
Control
Method
Mode
Speed reached output. SP_OK will be activated when the
Level
speed error is equal and below the setting value of P1-47.
Triggered
S, Sz
NOTE
1) When P2-18 to P2-22 and P2-37 is set to 0, it indicates output function is disabled.
7-102
Revision September 2013
Chapter 8 MODBUS
Communications
8.1 Communication Hardware Interface
The ASDA-B2 series servo drive has three modes of communication: RS-232 and RS-485.
All aspects of control, operation and monitoring as well as programming of the controller
can be achieved via communication. The two communication modes can be used at a time.
Please refer to the following sections for connections and limitations.
RS-232
 Connection
NOTE
1) Recommended maximum cable length is 15m (50ft.). Please note, RFI / EME noise should be
kept to a minimum, communication cable should kept apart from high voltage wires. If a
Revision September 2013
8-1
Chapter 8 MODBUS Communications
ASDA-B2
transmission speed of 38400 bps or greater is required, the maximum length of the
communication cable is 3m (9.84ft.) which will ensure the correct and desired baud rate.
2) The number shown in the pervious figure indicates the terminal number of each connector.
RS-485
 Connection
NOTE
1) The maximum cable length is 100m (39.37inches) when the servo drive is installed in a
location where there are only a few interferences. Please note, RFI / EME noise should be kept
to a minimum, communication cable should kept apart from high voltage wires. If a
transmission speed of 38400bps or greater is required, the maximum length of the
communication cable is 15m (50ft.) which will ensure the correct and desired baud rate.
2) The number shown in the pervious figure indicates the terminal number of each connector.
8-2
Revision September 2013
ASDA-B2
Chapter 8 MODBUS Communications
3) The power supply should provide a +12V and higher DC voltage.
4) Please use a REPEATER if more than 32 synchronous axes are required.
5) For the terminal identification of CN3, please refer to Section 3.5.
Revision September 2013
8-3
Chapter 8 MODBUS Communications
ASDA-B2
8.2 Communication Parameter Settings
The following describes the communication addresses for the communication parameters.
Parameters P3-00, P3-01, P3-02 and P3-05 are required to be set for any communication
between the servo drives and motors. The other optional parameters such as P3-03, P304, P3-06, P3-07 and P3-08 are used depending on different customer demands and
applications.
For optional communication parameters, please refer to the Chapter 7.
P3-00●
ADR
Address: 0300H
0301H
Communication Address Setting
Operation
Keypad / Software
Interface:
Related Section:
Section 8.2
Communication
Default: 0x7F
Control
ALL
Mode:
Unit: N/A
Range: 0x01 ~ 0x7F
Data Size: 16-bit
Display
Hexadecimal
Format:
Settings: This parameter is used to set the communication slave address in
hexadecimal format.
Display
0
0
Y
X
Range
-
-
0~7
0~F
X: Axis number which indicates the value must be within the range
from 0 through F.
Y: Group number which indicates the value must be within the range
from 0 to through 7
When using RS-232/485 communication, this parameter is used set
the communication address in hexadecimal format. If the AC servo
drive is controlled by RS-232/485 communication, each drive (or
device) must be uniquely identified. One servo drive only can set one
address. If the address is duplicated, there will be a communication
fault. This address is an absolute address which represents the servo
drive on a RS-232/485 network.
Please note:
1. When the address of host (external) controller is set to 0xFF, it is
with auto-respond function. Then, the servo drive will receive from
and respond to host (external) controller both no matter the
address is matching or not. However, the parameter P3-00 cannot
be set to 0xFF.
8-4
Revision September 2013
ASDA-B2
P3-01
Chapter 8 MODBUS Communications
BRT
Address: 0302H
0303H
Transmission Speed
Operation
Keypad / Software
Interface:
Related Section:
Section 8.2
Communication
Default: 0x0033
Control
ALL
Mode:
Unit: bps
Range: 0x0000 ~ 0x0055
Data Size: 16-bit
Display
Hexadecimal
Format:
Settings: This parameter is used to set the baud rate and data transmission
speed of the communications.
0
Z
Y
X
COM Port
-
-
RS-485
RS-232
Range
0
0
0~5
0~5
Settings:
0: Baud rate 4800 (data transmission speed: bits / second)
1: Baud rate 9600 (data transmission speed: bits / second)
2: Baud rate 19200 (data transmission speed: bits / second)
3: Baud rate 38400 (data transmission speed: bits / second)
4: Baud rate 57600 (data transmission speed: bits / second)
5: Baud rate 115200 (data transmission speed: bits / second)
P3-02
PTL
Address: 0304H
0305H
Communication Protocol
Operation
Keypad / Software
Interface:
Communication
Related Section:
Section 8.2
Default: 0x0066
Control
ALL
Mode:
Unit: N/A
Range: 0x0000 ~ 0x0088
Data Size: 16-bit
Display
Hexadecimal
Format:
Revision September 2013
8-5
Chapter 8 MODBUS Communications
ASDA-B2
Settings: This parameter is used to set the communication protocol. The
alphanumeric characters represent the following: 7 or 8 is the number
of data bits; N, E or O refers to the parity bit, Non, Even or Odd; the 1
or 2 is the numbers of stop bits.
0
Z
Y
X
COM Port
-
-
RS-485
RS-232
Range
0
0
0~8
0~8
0: Modbus ASCII mode, <7,N,2>
1: Modbus ASCII mode, <7,E,1>
2: Modbus ASCII mode, <7,O,1>
3: Modbus ASCII mode, <8,N,2>
4: Modbus ASCII mode, <8,E,1>
5: Modbus ASCII mode, <8,O,1>
6: Modbus RTU mode, <8,N,2>
7: Modbus RTU mode, <8,E,1>
8: Modbus RTU mode, <8,O,1>
P3-05
CMM
Communication Selection
Operation
Keypad / Software
Interface:
Communication
Address: 030AH
030BH
Related Section:
Section 8.2
Default: 1
Control
ALL
Mode:
Unit: N/A
Range: 0x00 ~ 0x01
Data Size: 16-bit
Display
Hexadecimal
Format:
Settings: RS-232 Communication interface selection
0: RS-232 via Modbus communication
1: RS-232 upon ASDA-Soft software
8-6
Revision September 2013
ASDA-B2
Chapter 8 MODBUS Communications
8.3 MODBUS Communication Protocol
When using RS-232/485 serial communication interface, each ASDA-B2 series AC servo
drive has a pre-assigned communication address specified by parameter “P3-00”. The
computer then controls each AC servo drive according to its communication address.
ASDA-B2 series AC servo drive can be set up to communicate on a MODBUS networks
using on of the following modes: ASCII (American Standard Code for Information
Interchange) or RTU (Remote Terminal Unit). Users can select the desired mode along
with the serial port communication protocol in parameter “P3-02”.
 Code Description:
ASCII Mode:
Each 8-bit data is the combination of two ASCII characters. For example, a 1-byte data: 64
Hex, shown as ‘64’ in ASCII, consists of ‘6’ (36Hex) and ‘4’ (34Hex).
The following table shows the available hexadecimal characters and their corresponding
ASCII codes.
Character
ASCII code
‘0’
‘1’
‘2’
‘3’
‘4’
‘5’
‘6’
‘7’
30H
31H
32H
33H
34H
35H
36H
37H
‘8’
‘9’
‘A’
‘B’
‘C’
‘D’
‘E’
‘F’
38H
39H
41H
42H
43H
44H
45H
46H
Character
ASCII code
RTU Mode:
Each 8-bit data is the combination of two 4-bit hexadecimal characters. For example, a 1byte data: 64 Hex.
 Data Format:
10-bit character frame (For 7-bit character)
7N2
Start
bit
0
1
2
3
4
5
6
Stop
bit
Stop
bit
5
6
Even
parity
Stop
bit
5
6
Odd
parity
Stop
bit
7-data bits
10-bits character frame
7E1
Start
bit
0
1
2
3
4
7-data bits
10-bits character frame
7O1
Start
bit
0
1
2
3
4
7-data bits
10-bits character frame
Revision September 2013
8-7
Chapter 8 MODBUS Communications
ASDA-B2
11-bit character frame (For 8-bit character)
8N2
Start
bit
0
1
3
2
4
5
6
7
Stop
bit
Stop
bit
6
7
Even
parity
Stop
bit
6
7
Odd
parity
Stop
bit
8-data bits
11-bits character frame
8E1
Start
bit
0
1
3
2
4
5
8-data bits
11-bits character frame
8O1
Start
bit
0
1
3
2
4
5
8-data bits
11-bits character frame
 Communication Protocol:
ASCII Mode:
Start
Slave address
Function
Start character’: ’ (3AH)
Communication address: 1-byte consists of 2 ASCII codes
Function code: 1-byte consists of 2 ASCII codes
DATA(n-1)
…….
Contents of data: n word = n x 2-byte consists of n x 4 ASCII codes,
n10
DATA(0)
LRC
LRC check sum: 1-byte consists of 2 ASCII codes
End 1
End code 1: (0DH)(CR)
End 0
End code 0: (0AH)(LF)
ASCII Mode: ’:’ character
ADR (Communication Address) consists of 2 ASCII codes and it ends in CR (Carriage Return) and
LF (Line Feed)
CR (Carriage Return) is represented by ASCII number 13, and LF (Line Feed) is represented by
ASCII number 10.
There are communication address, function code, contents of data, LRC (Longitudinal Redundancy
Check) between start and end characters.
8-8
Revision September 2013
ASDA-B2
Chapter 8 MODBUS Communications
RTU Mode:
Start
Slave address
Function
A silent interval of more than 10ms
Communication address: 1-byte
Function code: 1-byte
DATA(n-1)
…….
Contents of data: n word = n x 2-byte, n10
DATA(0)
CRC
CRC check sum: 1-byte
End 1
A silent interval of more than 10ms
RTU Mode: A silent interval of more than 10ms
RTU (Remote Terminal Unit) starts from a silent signal and ends at another silent signal.
There are communication address, function code, contents of data, CRC (Cyclical
Redundancy Check) between start and end characters.
DATA (Data Characters)
The format of data characters depends on the function code. The available command
codes and examples for AC servo drive are described as follows:
Example 1
Function code: 03H, read N words (multiple words). The maximum value of N is 10.
For example, reading continuous 2 words from starting address 0200H of AC servo drive
with address 01H.
ASCII Mode:
Command message:
Start
Slave address
Function
Starting data
address
Number of data
LRC Check
End 1
End 0
Response message:
‘:’
‘0’
‘1’
‘0’
‘3’
‘0’
‘2’
‘0’
‘0’
‘0’
‘0’
‘0’
‘2’
‘F’
‘8’
(0DH)(CR)
(0AH)(LF)
Start
Slave address
Function
Number of data
(In Byte)
Contents of
starting data
address 0200H
Contents of
second data
address 0201H
LRC Check
End 1
End 0
Revision September 2013
‘:’
‘0’
‘1’
‘0’
‘3’
‘0’
‘4'
‘0’
‘0’
‘B’
‘1’
‘1’
‘F’
‘4’
‘0’
‘E’
‘8’
(0DH)(CR)
(0AH)(LF)
8-9
Chapter 8 MODBUS Communications
ASDA-B2
RTU Mode:
Command message:
Response message:
Slave address
Function
Starting data
address
01H
03H
02H (Upper bytes)
00H (Lower bytes)
Slave address
Function
Number of data
(In Byte)
01H
03H
Number of data
(In Word)
00H
00H (Upper bytes)
02H
Contents of
starting data
address 0200H
CRC Check Low
C5H (Lower bytes)
CRC Check High
B3H (Upper bytes)
04H
B1H (Lower bytes)
Contents of
second data
address 0201H
1FH (Upper bytes)
CRC Check Low
CRC Check High
A3H (Lower bytes)
D4H (Upper bytes)
40H (Lower bytes)
Please note that a silent interval of more than 10ms is required before and after data
transmission in RTU mode.
Example 2
Function code: 06H, write 1 word
For example, writing 100 (0064H) to starting data address 0200H of ASDA-B2 series with
address 01H.
ASCII Mode:
Command message:
Start
Slave address
Function
Starting data
address
Content of data
LRC Check
End 1
End 0
8-10
Response message:
‘:’
‘0’
‘1’
‘0’
‘6’
‘0’
‘2’
‘0’
‘0’
‘0’
‘0’
‘6’
‘4’
‘9’
‘3’
(0DH)(CR)
(0AH)(LF)
Start
Slave address
Function
Starting data
address
Content of data
LRC Check
End 1
End 0
‘:’
‘0’
‘1’
‘0’
‘6’
‘0’
‘2'
‘0’
‘0’
‘0’
‘0’
‘6’
‘4’
‘9’
‘3’
(0DH)(CR)
(0AH)(LF)
Revision September 2013
ASDA-B2
Chapter 8 MODBUS Communications
RTU Mode:
Command message:
Response message:
Slave Address
01H
Slave Address
01H
Function
06H
Function
06H
Starting data
address
02H (Upper bytes)
Starting data
address
02H (Upper bytes)
Content of data
00H (Lower bytes)
00H (Upper bytes)
64H (Lower bytes)
Content of data
00H (Lower bytes)
00H (Upper bytes)
64H (Lower bytes)
CRC Check Low
89H (Lower bytes)
CRC Check Low
89H (Lower bytes)
CRC Check High
99H (Upper bytes)
CRC Check High
99H (Upper bytes)
Please note that a silent interval of more than 10ms is required before and after data
transmission in RTU mode.
Example 3
Function code: 10H, write N words (multiple words). The maximum value of N is 10.
For example, writing continuous 2 words, 0BB8H and 0000H from starting address 0112H
and address 0113H.
ASCII Mode:
Command message:
Start
Slave Address
Function
Response message:
‘:’
‘0’
‘1’
‘1’
‘0’
Start
Slave Address
Function
‘0’
Starting data
address
Number of data
(In Word)
Number of data
(In Byte)
Content of 1st data
Content of 2nd data
Revision September 2013
‘1’
‘1’
‘:’
‘0’
‘1’
‘1’
‘0’
‘0’
Starting data
address
‘1'
‘1’
‘2’
‘2’
‘0’
‘0’
‘0’
‘0’
‘2’
‘0’
‘4’
‘0’
‘B’
‘B’
‘8’
‘0’
‘0’
‘0’
‘0’
Content of data
LRC Check
End 1
End 0
‘0’
‘0’
‘2’
‘D’
‘A’
(0DH)(CR)
(0AH)(LF)
8-11
Chapter 8 MODBUS Communications
ASDA-B2
‘1’
LRC Check
‘3’
End 1
(0DH)(CR)
End 0
(0AH)(LF)
RTU Mode:
Command message:
Slave Address
Function
Starting data
address
Number of data
(In Word)
Number of data
(In Byte)
Content of 1st data
Content of 2nd
data
CRC Check Low
CRC Check High
01H
12H
00H
02H
Response message:
01H
10H
(Upper bytes)
(Lower bytes)
(Upper bytes)
(Lower bytes)
04H
Slave Address
Function
Starting data
address
Content of data
(In Word)
CRC Check Low
CRC Check High
01H
10H
01H (Upper bytes)
12H (Lower bytes)
00H (Upper bytes)
02H (Lower bytes)
E0H (Lower bytes)
31H (Upper bytes)
0BH (Upper bytes)
B8H (Lower bytes)
00H (Upper bytes)
00H (Lower bytes)
FCH (Lower bytes)
EBH (Upper bytes)
Please note that a silent interval of more than 10ms is required before and after data
transmission in RTU mode.
LRC (ASCII Mode):
LRC (Longitudinal Redundancy Check) is calculated by summing up, module 256, the
values of the bytes from ADR to last data character then calculating the hexadecimal
representation of the 2’s-complement negation of the sum.
Example
STX
ADR
CMD
Starting data address
Number of data
LRC Check
8-12
‘:’
‘7’
‘F’
‘0’
‘3’
‘0’
‘5’
‘C’
‘4’
‘0’
‘0’
‘0’
‘1’
‘B’
‘4’
Revision September 2013
ASDA-B2
Chapter 8 MODBUS Communications
End 1
End 0
(0DH)(CR)
(0AH)(LF)
7FH + 03H + 05H + C4H + 00H + 01H = 14CH, the 2’s complement negation of 4CH is
B4H.
Hence, we can know that LRC CHK is ’B’,’4’.
CRC (RTU Mode):
CRC (Cyclical Redundancy Check) is calculated by the following steps:
Step 1: Load a 16-bit register (called CRC register) with FFFFH.
Step 2: Exclusive OR the first 8-bit byte of the command message with the low order byte
of the 16-bit CRC register, putting the result in the CRC register.
Step 3: Extract and examine the LSB. If the LSB of CRC register is 0, shift the CRC
register one bit to the right. If the LSB of CRC register is 1, shift the CRC register
one bit to the right, then Exclusive OR the CRC register with the polynomial value
A001H.
Step 4: Repeat step 3 until eight shifts have been performed. When this is done, a
complete 8-bit byte will have been processed, then perform step 5.
Step 5: Repeat step 2 to step 4 for the next 8-bit byte of the command message.
Continue doing this until all bytes have been processed. The final contents of the
CRC register are the CRC value.
NOTE
1) When transmitting the CRC value in the message, the upper and lower bytes of the CRC value
must be swapped, i.e. the lower order byte will be transmitted first.
2) For example, reading 2 words from address 0101H of the AC servo drive with address 01H.
The final content of the CRC register from ADR to last data character is 3794H, then the
command message is shown as follows. What should be noticed is that 94H have to be
transmitted before 37H.
Command Message
ADR
CMD
Starting data
address
Number of data
(In Word)
CRC Check Low
CRC Check High
Revision September 2013
01H
03H
01H (Upper byte)
01H (Lower bytes)
00H (Upper bytes)
02H (Lower bytes)
94H (Lower bytes)
37H (Upper bytes)
8-13
Chapter 8 MODBUS Communications
ASDA-B2
End1, End0 (Communication End)
ASCII Mode:
In ASCII mode, (0DH) stands for character ’\r’ (carriage return) and (0AH) stands for
character ’\n’ (new line), they indicate communication end.
RTU Mode:
In RTU mode, a silent interval of more than 10ms indicates communication end.
CRC Program Example
The following is an example of CRC generation using C language. The function takes two
arguments:
unsigned char* data;
unsigned char length
The function returns the CRC value as a type of unsigned integer.
unsigned int crc_chk(unsigned char* data, unsigned char length) {
int j;
unsigned int reg_crc=0xFFFF;
while( length-- ) {
reg_crc^= *data++;
for (j=0; j<8; j++ ) {
if( reg_crc & 0x01 ) { /*LSB(bit 0 ) = 1 */
reg_crc = (reg_crc >> 1)^0xA001;
} else {
reg_crc = (reg_crc>>1);
}
}
}
return reg_crc;
}
PC communication program example:
#include<stdio.h>
#include<dos.h>
#include<conio.h>
#include<process.h>
#define PORT 0x03F8 /* the address of COM 1 */
#define THR 0x0000
#define RDR 0x0000
8-14
Revision September 2013
ASDA-B2
Chapter 8 MODBUS Communications
#define BRDL 0x0000
#define IER 0x0001
#define BRDH 0x0001
#define LCR 0x0003
#define MCR 0x0004
#define LSR 0x0005
#define MSR 0x0006
unsigned char rdat[60];
/* read 2 data from address 0200H of ASD with address 1 */
unsigned char tdat[60]={‘:’,’0’,’1’,’0’,’3’,’0’,’2’,’0’,’0’,’0’,’0’,’0’,’2’,’F’,’8’,’\r’,’\n’};
void main() {
int I;
outportb(PORT+MCR,0x08);
/* interrupt enable */
outportb(PORT+IER,0x01);
/* interrupt as data in */
outportb(PORT+LCR,( inportb(PORT+LCR) | 0x80 ) );
/* the BRDL/BRDH can be access as LCR.b7 == 1 */
outportb(PORT+BRDL,12);
outportb(PORT+BRDH,0x00);
outportb(PORT+LCR,0x06);
/* set prorocol
<7,E,1> = 1AH,
<7,O,1> = 0AH
<8,N,2> = 07H
<8,E,1> = 1BH
<8,O,1> = 0BH
*/
for( I = 0; I<=16; I++ ) {
while( !(inportb(PORT+LSR) & 0x20) ); /* wait until THR empty */
outportb(PORT+THR,tdat[I]);
/* send data to THR */
}
I = 0;
while( !kbhit() ) {
if( inportb(PORT+LSR)&0x01 ) { /* b0==1, read data ready */
rdat[I++] = inportb(PORT+RDR); /* read data from RDR */
}
}
}
Revision September 2013
8-15
Chapter 8 MODBUS Communications
ASDA-B2
8.4 Communication Parameter Write-in and Read-out
There are following five groups for parameters:
Group 0: Monitor parameter
(example: P0-xx)
Group 1: Basic parameter
(example: P1-xx)
Group 2: Extension parameter
(example: P2-xx)
Group 3: Communication parameter
(example: P3-xx)
Group 4: Diagnosis parameter
(example: P4-xx)
For a complete listing and description of all parameters, refer to Chapter 7.
Communication write-in parameters for ASDA-B2 series are including:
Group 0: All parameters except P0-00 ~ P0-01, P0-08 ~ P0-13 and P0-46
Group 1: P1-00 ~ P1-76
Group 2: P2-00 ~ P2-67
Group 3: P3-00 ~ P3-11
Group 4: All parameters except P4-00 ~ P4-04 and P4-08 ~ P4-09
NOTE
1) P3-01
After the new transmission speed is set, the next data will be written in new
transmission speed.
2) P3-02
After the new communication protocol is set, the next data will be written in new
communication protocol.
3) P4-05
JOG control of servo motor. For the description, refer to Chapter 7.
4) P4-06
Force output contact control. This parameter is for the users to test if DO (Digit
output) is normal. User can set 1, 2, 4, 8, 16, 32 to test DO1, DO2, DO3, DO4, DO5,
DO6 respectively. After the test has been completed, please set this parameter to 0
to inform the drive that the test has been completed.
5) P4-10
Adjustment function selection. If the user desires to change the settings of this
parameter, the user has to set the value of the parameter P2-08 to 20 (hexadecimal:
14H) first and then restart. After restarting, the settings of parameter P4-10 can
become modified.
6) P4-11 ~ P4-21
These parameters are for offset adjustment. Do not change the factory
default setting if not necessary. If the user desires to change the settings of
these parameters, the user has to set the value of the parameter P2-08 to 22
(hexadecimal: 16H) first and then restart. After restarting, the settings of
parameters P4-11 to P4-21 can become modified.
8-16
Revision September 2013
ASDA-B2
Chapter 8 MODBUS Communications
Communication read-out parameters for ASDA-B2 series are including:
Group 0: P0-00 ~ P0-46
Group 1: P1-00 ~ P1-76
Group 2: P2-00 ~ P2-67
Group 3: P3-00 ~ P3-11
Group 4: P4-00 ~ P4-24
Revision September 2013
8-17
Chapter 8 MODBUS Communications
ASDA-B2
This page is intentionally left blank.
8-18
Revision September 2013
Chapter 9 Troubleshooting
If a fault is detected on the servo drive or motor a corresponding fault code will be shown
on the drive's LED display. Fault codes can also be transmitted via communication, see
P0-01 and P4-00 ~ P4-04 for display on controller or HMI.
9.1 Fault Messages Table
Servo Drive Fault Messages
Fault Messages
Display
Fault Name
Fault Description
Overcurrent
Main circuit current is higher than 1.5 multiple of motor’s
instantaneous maximum current value.
Overvoltage
Main circuit voltage has exceeded its maximum allowable
value.
Undervoltage
Main circuit voltage is below its minimum specified value.
Motor error
The motor does not match the drive. They are not
correctly matched for size (power rating).
Regeneration error
Regeneration control operation is in error.
Overload
Servo motor and drive is overload.
Overspeed
Motor’s control speed exceeds the limit of normal speed.
Abnormal pulse
control command
Input frequency of pulse command exceeds the limit of its
allowable setting value.
Excessive deviation
Position control deviation value exceeds the limit of its
allowable setting value.
Reserved
Reserve
Encoder error
Pulse signal is in error.
Adjustment error
Adjusted value exceeds the limit of its allowable setting
value when perform electrical adjustment.
Emergency stop
activated
Emergency stop switch is activated.
Reverse limit switch
error
Reverse limit switch is activated.
Forward limit switch
error
Forward limit switch is activated.
IGBT temperature error The temperature of IGBT is over high.
Memory error
Revision September 2013
EE-PROM write-in and read-out is in error.
9-1
Chapter 9 Troubleshooting
ASDA-B2
Fault Messages
Display
Fault Name
Fault Description
Encoder output error
The encoder output exceeds the rated output frequency.
Serial communication
error
RS232/485 communication is in error.
Serial communication
time out
RS232/485 communication time out.
Reserved
Reserve
Input power phase loss One phase of the input power is loss.
Pre-overload warning
Encoder initial
magnetic field error
To warn that the servo motor and drive is going to overload.
This alarm will display before ALM06. When the servo motor
reach the setting value of P1-56, the motor will send a
warning to the drive. After the drive has detected the warning,
the DO signal OLW will be activated and this fault message
will display.
The magnetic field of the encoder U, V, W signal is in error.
Encoder internal error
The internal memory of the encoder is in error. An internal
counter error is detected.
Encoder data error
An encoder data error is detected for three times.
Motor internal error
The setting value of the encoder is in error.
Motor internal error
The encoder U, V, W signals are in error.
Motor internal error
The internal address of the encoder is in error.
Motor protection error
In order to protect the motor, this alarm will be activated
when the setting value of P1-57 is reached after a period of
time set by P1-58.
U,V,W, GND wiring
error
The wiring connections of U, V, W (for servo motor output)
and GND (for grounding) are in error.
Motor temperature
error
Motor is working under temperature over 105°C (221°F).
Excessive encoder
output error
The encoder output errors or output pulses exceed hardware
tolerance.
Motor temperature
warning
The temperature of motor is over 85°C (185°F).
EE-PROM is not reset after the firmware version is upgraded.
DSP firmware upgrade This fault can be cleared after setting P2-08 to 30 first, and
then setting P2-08 to 28 next and restarting the ervo drive.
NOTE
1) If there is any unknown fault code that is not listed on the above table, please inform the
distributor or contact with Delta for assistance.
9-2
Revision September 2013
ASDA-B2
Chapter 9 Troubleshooting
9.2 Potential Cause and Corrective Actions
Servo Drive Fault Messages
: Overcurrent
Potential Cause
Checking Method
Corrective Actions
Short-circuit at drive
output (U, V, W)
1. Check the wiring connections between
drive and motor.
2. Check if the wire is short-circuited.
Repair the short-circuited and
avoid metal conductor being
exposed.
Motor wiring error
Check if the wiring steps are all correct
when connecting motor to drive.
Follow the wiring steps in the
user manual to reconnect
wiring.
IGBT error
Heat sink overheated
Please contact your distributor
for assistance or contact with
Delta.
Control parameter
setting error
Check if the setting value exceeds the
factory default setting.
Set the setting back to factory
default setting and then reset
and adjust the parameter setting
again.
Check if the control input command is
unstable (too much fluctuation).
1. Ensure that input command
frequency is stable (too much
fluctuation).
2. Activate filter function.
Control command
setting error
: Overvoltage
Potential Cause
Checking Method
Corrective Actions
The main circuit
voltage has
exceeded its
maximum allowable
value.
Use voltmeter to check whether the input Use correct power supply or
voltage falls within the rated input voltage. stabilizing power.
Input power error
(Incorrect power
input)
Use voltmeter to check whether the input
voltage is within the specified limit.
Use correct power supply or
stabilizing power.
: Undervoltage
Potential Cause
Checking Method
Corrective Actions
The main circuit
voltage is below its
minimum specified
value.
Check whether the wiring of main circuit
input voltage is normal.
Reconfirm voltage wiring.
No input voltage at
main circuit.
Use voltmeter to check whether input
voltage at main circuit is normal.
Reconfirm power switch.
Input power error
(Incorrect power
input)
Use voltmeter to check whether the input
voltage is within the specified limit.
Use correct power supply or
serial stabilizing power.
Revision September 2013
9-3
Chapter 9 Troubleshooting
ASDA-B2
: Motor error
Potential Cause
Checking Method
Corrective Actions
Encoder is damage.
Check Encoder for the damage.
Repair or replace the motor.
Encoder is loose.
Examine the Encoder connector.
Install the motor again.
The type of the servo Check if the servo drive and servo motor Replace the motor.
are not correctly matched for size (power
motor is incorrect.
rating).
: Regeneration error
Potential Cause
Checking Method
Corrective Actions
Regenerative resistor Check the wiring connection of
is not connected.
regenerative resistor.
Reconnect regenerative resistor.
Regenerative switch Check if regenerative switch transistor is
transistor fault
short-circuited.
Please contact your distributor
for assistance or contact with
Delta.
Parameter setting is
in error
Correctly reset parameter again.
Confirm the parameter setting and
specifications of regenerative resistor.
: Overload
Potential Cause
Checking Method
The drive has
exceeded its rated
Check if the drive is overloaded.
load during
continuous operation.
Control system
parameter setting is
incorrect.
The wiring of drive
and encoder is in
error.
Corrective Actions
Increase motor capacity or
reduce load.
Check if there is mechanical vibration
Adjust gain value of control
circuit.
Accel/Decel time setting is too fast.
Decrease Accel/Decel time
setting.
Check the wiring of U, V, W and encoder.
Ensure all wiring is correct.
: Overspeed
Potential Cause
Checking Method
Corrective Actions
Speed input
command is not
stable (too much
fluctuation).
Ensure that input command
frequency is stable (not
Use signal detector to detect if input signal
fluctuate too much) and
is abnormal.
activate filter function (P1-06,
P1-07 and P1-08).
Over-speed
parameter setting is
defective.
Check if over-speed parameter setting
value is too low.
9-4
Correctly set over-speed
parameter setting (P2-34).
Revision September 2013
ASDA-B2
Chapter 9 Troubleshooting
: Abnormal pulse control command
Potential Cause
Pulse command
frequency is higher
than rated input
frequency.
Checking Method
Use pulse frequency detector to measure
input frequency.
Corrective Actions
Correctly set the input pulse
frequency.
: Excessive deviation
Potential Cause
Checking Method
Corrective Actions
Maximum deviation
parameter setting is
too small.
Check the maximum deviation parameter
setting and observe the position error
value when the motor is running.
Increases the parameter setting
value of P2-35.
Gain value is too
small.
Check for proper gain value.
Correctly adjust gain value.
Torque limit is too
low.
Check torque limit value.
Correctly adjust torque limit
value.
There is an overload. Check for overload condition.
Reduce external applied load or
re-estimate the motor capacity.
: Reserved
: Encoder error (Position detector fault)
Potential Cause
Checking Method
Corrective Actions
1. Check if all wiring is correct.
The wiring of encoder is 2. Check if the users conduct the wiring
Ensure all wiring is correct.
in error.
by the wiring information in the user
manual.
Encoder is loose
Examine the encoder connector.
Install the motor again.
The wiring of encoder is
Check if all connections are tight.
defective.
Conduct the wiring again.
Encoder is damage
Repair or replace the motor.
Check the encoder for the damage.
: Adjustment error
Potential Cause
Checking Method
The setting value of drift 1. Remove CN1 wiring.
adjustment has
2. Execute the drift adjustment again.
exceeded its maximum
(Set P2-08 to 20 first, and then set
allowable value.
P4-10 to 5.)
Corrective Actions
If the error does not clear after
executing the drift adjustment
again, please contact your
distributor for assistance or
contact with Delta.
: Emergency stop activated
Potential Cause
Checking Method
Corrective Actions
Emergency stop switch Check if emergency stop switch is On or
Activate emergency stop switch.
is activated.
Off.
Revision September 2013
9-5
Chapter 9 Troubleshooting
ASDA-B2
: Reverse (CWL) limit switch error
Potential Cause
Checking Method
Corrective Actions
Reverse limit switch is
activated.
Check if reverse limit switch is On or Off. Activate reverse limit switch.
Servo system is not
stable.
Check the value of control parameter
setting and load inertia.
Modify parameter setting and
re-estimate motor capacity.
: Forward (CCWL) limit switch error
Potential Cause
Checking Method
Corrective Actions
Forward limit switch is
activated.
Check if forward limit switch is On or Off. Activate forward limit switch.
Servo system is not
stable.
Check the value of control parameter
setting and load inertia.
Modify parameter setting and
re-estimate motor capacity.
: IGBT temperature error
Potential Cause
Checking Method
Corrective Actions
The drive has exceeded
Check if there is overload or the motor
its rated load during
current is too high.
continuous operation.
Increase motor capacity or
reduce load.
Short-circuit at drive
output.
Ensure all wiring is correct.
Check the drive input wiring.
: Memory error
Potential Cause
Parameter data error
when writing into EEPROM.
The setting value of
hidden parameter is in
error.
9-6
Checking Method
Corrective Actions
Examine the parameter settings. Please
do the following steps:
1. Press SHIFT key on the drive keypad,
and examine the parameter shown on
LED display.
2. If E320A is displayed (in hexadecimal
format), it indicates it is parameter P210. Please examine the parameter
settings of P2-10.
3. If E3610 is displayed (in hexadecimal
format), it indicates it is parameter P616. Please examine the parameter
settings of P6-16.
1. If this fault occurs when
power is applied to the drive,
it indicates that the setting
value of one parameter has
exceeded the specified range.
Correct the setting value of
the parameter to clear the
fault and restart the servo
drive.
2. If this fault occurs during
normal operation, it indicates
that the error occurs when
writing data into EE-PROM.
Turn ARST (DI signal) ON to
clear the fault or restart the
servo drive.
Press SHIFT key on the drive keypad
and examine if E100X is displayed on
LED display.
If this fault occurs when
resetting the parameter settings,
it indicates that the servo drive
type is not set correctly.
Correctly set the servo drive
type again.
Revision September 2013
ASDA-B2
Chapter 9 Troubleshooting
Potential Cause
Data in EE-PROM is
damaged.
Checking Method
Press SHIFT key on the drive keypad
and examine if E0001 is displayed on
LED display.
Corrective Actions
If this fault occurs when power
is applied to the drive, it
indicates that the data in EERPM is damaged or there is no
data in EE-PROM. Please
contact your distributor for
assistance or contact with Delta.
: Encoder output error
Potential Cause
Encoder itself or the
wiring of encoder is in
error.
Checking Method
Corrective Actions
Check if the recent fault records (P4-00
Perform the corrective actions
~ P4-05) display on the drive keypad in
as described in AL011, AL024,
accordance with the fault codes AL011,
AL025 and AL026.
AL024, AL025 and AL026.
Check if the following conditions occur:
Condition 1: Motor speed is above the
value set by P1-76.
Condition 2:
The output frequency
for pulse output may
exceed the limit of its
allowable setting value. Motor Speed
60
 P1  46  4  19.8  10 6
Correctly set P1-76 and P1-46.
1. Ensure that the motor speed
is below the value set by P176.
2.
Motor Speed
 P1  46  4  19.8  106
60
: Serial communication error
Potential Cause
Checking Method
Corrective Actions
Communication
parameter setting is
defective.
Check the communication parameter
Correctly set parameter setting.
setting.
Communication
address is incorrect.
Check the communication address.
Communication value is
Check the communication value.
incorrect.
Correctly set communication
address.
Correctly set communication
value.
: Serial communication time out
Potential Cause
Checking Method
Corrective Actions
Setting value in time out
Check communication time out
parameter is not
parameter setting.
correct.
Correctly set P3-07.
Not receiving
communication
command for a long
time.
Tighten the communication
cable, make sure the
communication cable is not
damaged and ensure all wiring
is correct.
Check whether communication cable is
loose or broken.
: Reserved
Revision September 2013
9-7
Chapter 9 Troubleshooting
ASDA-B2
: Input power phase loss
Potential Cause
Checking Method
Corrective Actions
If the fault does not clear even
Check the power cable and connections
when the three-phase power is
Control power supply is of R, S, and T. Check whether the power
connected correctly, please
cable is loose or the possible loss of
in error.
contact your distributor for
phase on input power.
assistance or contact with Delta.
: Pre-overload warning
Potential Cause
The drive is going to
overload.
Checking Method
Corrective Actions
1. Check the load condition of the servo 1. Please refer to the
motor and drive.
correction actions of ALE06.
2. Check the setting value of P1-56.
2. Increase the setting value of
Check whether the setting value of
P1-56 or set P1-56 to 100
P1-56 is too small.
and above.
: Encoder initial magnetic field error
Potential Cause
The magnetic field of
the encoder U, V, W
signal is in error.
Checking Method
Corrective Actions
1. Check if the servo motor is properly
grounded.
2. Check if the encoder signal cables are
placed in separate conduits from the
cables connected to R, S, T and U, V,
W terminals to prevent the
interference.
3. Check if the shielded cables are used
when performing encoder wiring.
If the error does not clear after
each checking is done, please
contact your distributor for
assistance or contact with Delta.
: Encoder internal error
Potential Cause
Checking Method
Corrective Actions
1. Please connect the grounding
(green color) of U, V, W
terminal to the heat sink of the
servo drive.
1. Check if the servo motor is properly
2. Ensure that the encoder
grounded.
signal cables are placed in
separate conduits from the
2. Check if the encoder signal cables are
The internal memory of
cables connected to R, S, T
placed in separate conduits from the
the encoder is in error.
and U, V, W terminals to
cables connected to R, S, T and U, V,
An encoder counter
prevent the interference.
W terminals to prevent the
error occurs.
interference.
3. Please use shielded cables
for Encoder wiring.
3. Check if the shielded cables are used
when performing encoder wiring.
4. If the error does not clear
after all the above actions are
done, please contact your
distributor for assistance or
contact with Delta.
9-8
Revision September 2013
ASDA-B2
Chapter 9 Troubleshooting
: Encoder data error
Potential Cause
An encoder data error
occurs for three times.
Checking Method
Corrective Actions
1. Please connect the grounding
(green color) of U, V, W
terminal to the heat sink of the
servo drive.
1. Check if the servo motor is properly
2. Ensure that the encoder
grounded.
signal cables are placed in
separate conduits from the
2. Check if the encoder signal cables are
cables connected to R, S, T
placed in separate conduits from the
and U, V, W terminals to
cables connected to R, S, T and U, V,
prevent the interference.
W terminals to prevent the
interference.
3. Please use shielded cables
for Encoder wiring.
3. Check if the shielded cables are used
when performing encoder wiring.
4. If the error does not clear
after all the above actions are
done, please contact your
distributor for assistance or
contact with Delta.
:Motor internal error
Potential Cause
Checking Method
Corrective Actions
1. Please connect the grounding
(green color) of U, V, W
terminal to the heat sink of
the servo drive.
1. Check if the servo motor is properly
2. Ensure that the encoder
grounded.
signal cables are placed in
separate conduits from the
2. Check if the encoder signal cables are
cables connected to R, S, T
placed in separate conduits from the
The setting value of the
and U, V, W terminals to
cables connected to R, S, T and U, V,
encoder is in error.
prevent the interference.
W terminals to prevent the
interference.
3. Please use shielded cables
for Encoder wiring.
3. Check if the shielded cables are used
when performing encoder wiring.
4. If the error does not clear
after all the above actions are
done, please contact your
distributor for assistance or
contact with Delta.
:Motor internal error
Potential Cause
The encoder U, V, W
signals are in error.
Revision September 2013
Checking Method
Corrective Actions
1. Please connect the grounding
1. Check if the servo motor is properly
(green color) of U, V, W
grounded.
terminal to the heat sink of
2. Check if the encoder signal cables are
the servo drive.
placed in separate conduits from the
cables connected to R, S, T and U, V, 2. Ensure that the encoder
signal cables are placed in
W terminals to prevent the
separate conduits from the
interference.
cables connected to R, S, T
3. Check if the shielded cables are used
and U, V, W terminals to
9-9
Chapter 9 Troubleshooting
ASDA-B2
when performing encoder wiring.
prevent the interference.
3. Please use shielded cables
for Encoder wiring.
4. If the error does not clear
after all the above actions are
done, please contact your
distributor for assistance or
contact with Delta.
:Motor internal error
Potential Cause
Checking Method
Corrective Actions
1. Please connect the grounding
(green color) of U, V, W
terminal to the heat sink of
the servo drive.
1. Check if the servo motor is properly
2. Ensure that the encoder
grounded.
signal cables are placed in
separate conduits from the
2. Check if the encoder signal cables are
cables connected to R, S, T
placed in separate conduits from the
The internal address of
and U, V, W terminals to
cables connected to R, S, T and U, V,
the encoder is in error.
prevent the interference.
W terminals to prevent the
interference.
3. Please use shielded cables
for Encoder wiring.
3. Check if the shielded cables are used
when performing encoder wiring.
4. If the error does not clear
after all the above actions are
done, please contact your
distributor for assistance or
contact with Delta.
: Motor protection error
Potential Cause
The setting value of
parameter P1-57 is
reached after a period
of time set by
parameter P1-58.
Checking Method
1. Check if P1-57 is enabled.
2. Check if the setting values of P1-57
and P1-58 are both too small.
Corrective Actions
1. Set P1-57 to 0.
2. Correctly set P1-57 and P158. Please note that the overlow setting may results in
malfunction, but over-high
setting may let the motor
protection function not
operate.
: U, V, W, GND wiring error
Potential Cause
Checking Method
Corrective Actions
The wiring connections
of U, V, W (for servo
Check if wiring connections of U, V, and
motor output) and GND
Follow the wiring steps in the
W are not correct.
(for grounding) are in
user manual to reconnect the
error.
wiring and ground the servo
The ground connection Check if the ground connection is loose drive and motor properly.
and ensure the ground is conducting
is loose or not
properly.
conducting properly.
9-10
Revision September 2013
ASDA-B2
Chapter 9 Troubleshooting
: Motor temperature error
Potential Cause
Checking Method
Corrective Actions
Motor is working under
Check if the environment temperature is Try to reduce environment
temperature over 105°C
too high.
temperature.
(221°F).
: Excessive encoder output error
Potential Cause
Encoder error causes
abnormal encoder
output.
Output pulses exceed
hardware tolerance.
Checking Method
Corrective Actions
Exam error records (P4-00~P4-05)
Please refer to AL011, AL024, AL025,
to check if encoder errors
occurred. (AL011, AL024, AL025, AL026 and take corrective actions.
AL026)
Check if conditions below occur,
P1-76 < Motor rotation speed, or,
Motor rotation speed
60
Correctly set P1-76 and P1-46:
P1-76 > Motor rotation speed, and,
 P1  46  4  19.8  10 Motor rotation speed
 P1  46  4  19.8  10 6
60
: Motor temperature warning
Potential Cause
Checking Method
Corrective Actions
Motor is working under
Check if the environment temperature is Try to reduce environment
temperature over 85°C
too high.
temperature.
(185°F).
: DSP firmware upgrade
Potential Cause
EE-PROM is not reset
after the firmware
version is upgraded.
Revision September 2013
Checking Method
Check if EE-PROM is reset after the
firmware version is upgraded.
Corrective Actions
Set P2-08 to 30 first, and then
28 next, and restart the servo
drive.
9-11
Chapter 9 Troubleshooting
ASDA-B2
9.3 Clearing Faults
Display
9-12
Fault Name
Clearing Method
Overcurrent
Turn ARST (DI signal) ON to clear the fault
or restart the servo drive.
Overvoltage
Turn ARST (DI signal) ON to clear the fault
or restart the servo drive.
Undervoltage
This fault message can be removed
automatically after the voltage has returned
within its specification.
Motor error
This fault message can be removed by
restarting the servo drive.
Regeneration error
Turn ARST (DI signal) ON to clear the fault
or restart the servo drive.
Overload
Turn ARST (DI signal) ON to clear the fault
or restart the servo drive.
Overspeed
Turn ARST (DI signal) ON to clear the fault
or restart the servo drive.
Abnormal pulse control
command
Turn ARST (DI signal) ON to clear the fault
or restart the servo drive.
Excessive deviation
Turn ARST (DI signal) ON to clear the fault
or restart the servo drive.
Reserved
This fault message cannot be cleared.
Encoder error
This fault message can be removed by
restarting the servo drive.
Adjustment error
This fault message can be removed after the
wiring of CN1 connector (I/O signal
connector) is removed and auto adjustment
function is executed.
Emergency stop activated
This fault message can be removed
automatically by turning off EMGS (DI
signal).
Reverse limit switch error
Turn ARST (DI signal) ON to clear the fault.
This fault message can be removed when
the servo drive is Off (Servo Off)
Forward limit switch error
Turn ARST (DI signal) ON to clear the fault.
This fault message can be removed when
the servo drive is Off (Servo Off)
IGBT temperature error
Turn ARST (DI signal) ON to clear the fault
or restart the servo drive.
Memory error
Turn ARST (DI signal) ON to clear the fault
or restart the servo drive.
Encoder output error
Turn ARST (DI signal) ON to clear the fault.
Revision September 2013
ASDA-B2
Display
Chapter 9 Troubleshooting
Fault Name
Clearing Method
Turn ARST (DI signal) ON to clear the fault.
This fault message can also be removed
Serial communication error
automatically after the communication is
normal.
Serial communication time Turn ARST (DI signal) ON to clear the fault
out
or restart the servo drive.
Revision September 2013
Reserved
This fault message cannot be cleared.
Input power phase loss
Turn ARST (DI signal) ON to clear the fault.
This fault message can be removed
automatically after input power phase lost
problem is solved.
Pre-overload warning
Turn ARST (DI signal) ON to clear the fault
or restart the servo drive.
Encoder initial magnetic
field error
This fault message can be removed by
restarting the servo drive.
Encoder internal error
This fault message can be removed by
restarting the servo drive.
Encoder data error
This fault message can be removed by
restarting the servo drive.
Motor internal error
This fault message can be removed by
restarting the servo drive.
Motor internal error
This fault message can be removed by
restarting the servo drive.
Motor internal error
This fault message can be removed by
restarting the servo drive.
Motor protection error
Turn ARST (DI signal) ON to clear the fault.
U,V,W, GND wiring error
This fault message can be removed by
restarting the servo drive.
Motor temperature error
This fault message can be removed by
restarting the servo drive.
Excessive encoder output
error
Turn ARST (DI signal) ON to clear the fault.
Motor temperature warning
This fault message can be removed after
temperature drops to normal degree.
DSP firmware upgrade
This fault message can be removed after
setting P2-08 to 30 first, and then 28 next
and restarting the servo drive.
9-13
Chapter 9 Troubleshooting
ASDA-B2
This page is intentionally left blank.
9-14
Revision September 2013
Chapter 10 Specifications
10.1 Specifications of Servo Drives (ASDA-B2 Series)
Power
Supply
Model: ASDA-B2 Series
Phase / Voltage
Continuous Output Current
Cooling System
Position Control Mode
200W
400W
750W
1kW
1.5kW
2kW
3kW
01
02
04
07
10
15
20
30
Three-phase: 170 ~ 255VAC, 50/60Hz ±5%
Single-phase: 200 ~ 255VAC, 50/60Hz ±5%
0.9
Arms
1.55
Arms
2.6
Arms
5.1
Arms
7.3
Arms
Natural Air Circulation
8.3
Arms
Three-phase:
170 ~ 255VAC,
50/60Hz ±5%
13.4
Arms
19.4
Arms
Fan Cooling
Encoder Resolution /
Feedback Resolution
17-bit (160000 p/rev)
Control of Main Circuit
SVPWM Control
Tuning Modes
Auto / Manual
Dynamic Brake
Speed Control Mode
100W
-
Built-in
Max. Input Pulse Frequency
Line driver: Max. 500Kpps (low speed)/ Max.4Mpps(high speed)
Open collector: Max. 200Kpps
Pulse Type
Pulse + Direction, A phase + B phase, CCW pulse + CW pulse
Command Source
External pulse train
Smoothing Strategy
Low-pass filter
Electronic Gear
Electronic gear N/M multiple
N: 1 ~ (226-1)/M:1 ~ (231-1)
1/50 < N/M < 25600
Torque Limit Operation
Set by parameters
Feed Forward Compensation
Set by parameters
Voltage Range
Analog Input
Input Resistance
Command
Time Constant
0 ~ ±10 VDC
Speed Control Range*1
1:5000
Command Source
External analog signal / Internal parameters
Smoothing Strategy
Low-pass and S-curve filter
Torque Limit Operation
Set by parameters or via Analog input
Responsiveness Characteristic
Maximum 550Hz
10K
2.2 us
0.01% or less at load fluctuation 0 to 100%
Speed Fluctuation Rate*2
(at rated speed)
0.01% or less at power fluctuation ±10%
o
o
0.01% or less at ambient temperature fluctuation 0 C to 50 C
Revision September 2013
10-1
Chapter 10 Specifications
ASDA-B2
Torque Control Mode
Model: ASD-B2 Series
Analog Input
Command
100W
200W
400W
750W
1kW
1.5kW
2kW
3kW
01
02
04
07
10
15
20
30
Voltage Range
0 ~ ±10 VDC
Input
Resistance
10K
Time Constant
2.2 us
Command Source
External analog signal / Internal parameters
Smoothing Strategy
Low-pass filter
Speed Limit Operation
Parameter Setting or via Analog input
Analog Monitor Output
Inputs
Digital
Inputs/Outputs
Monitor signal can set by parameters (Output voltage range: ±8V)
Servo On, Reset, Gain switching, Pulse clear, Zero speed CLAMP,
Command input reverse control, Speed/Torque limit enabled, Speed
command selection, Position / Speed mode switching, Speed / Torque
mode switching, Torque / Position mode switching, Emergency stop,
Forward / Reverse inhibit limit, Forward / Reverse operation torque limit,
Forward / Reverse JOG input, Electronic gear ratio (Numerator) selection
and Pulse inhibit input
Encoder signal output (A, B, Z Line Driver / Z Open collector)
Outputs
Servo ready, Servo On, At Zero speed, At Speed reached, At Positioning
completed, At Torques limit, Servo alarm (Servo fault) activated,
Electromagnetic brake control, Output overload warning, Servo warning
activated
Protective Functions
Overcurrent, Overvoltage, Undervoltage, Motor overheated, Overload,
Overspeed, Excessive deviation, Regeneration error, Abnormal pulse
control command, Encoder error, Adjustment error, Emergency stop
activated, Reverse/ Forward limit switch error, IGBT temperature error,
Serial communication error, Input power phase loss, Serial
communication time out, terminals with short circuit protection (U, V ,W ,
CN1, CN2, CN3 terminals)
Communication Interface
RS-232/RS-485
Installation Site
Indoor location (free from direct sunlight), no corrosive liquid and gas (far
away from oil mist, flammable gas, dust)
Altitude
Altitude 1000m or lower above sea level
Atmospheric pressure
86kPa to 106kPa
o
Environment
Operating Temperature
o
0 C to 55 C
(32°F to 131°F) (If operating temperature is above specified
range, forced cooling will be required)
Storage Temperature
-20℃ ~ 65℃
Humidity
0 to 90% (non-condensing)
2
2
Vibration
9.80665m/s (1G) less than 20Hz, 5.88m/ s (0.6G) 20 to 50Hz
IP Rating
IP20
Power System
TN System *4
IEC/EN 61800-5-1, UL 508C
Standards/Requirement
10-2
Revision September 2013
ASDA-B2
Chapter 10 Specifications
Footnote:
*1
Rated rotation speed: When full load, speed ratio is defined as the minimum speed (the motor
not pause).
*2
When command is rated rotation speed, the speed fluctuation rate is defined as:
will
(Empty load rotation speed – Full load rotation speed) / Rated rotation speed
*3
TN system: A power distribution system having one point directly earthed, the exposed
parts of the installation being connected to that points by protective earth
conductor.
*4
Please refer to “Chart of load and operating time” in section 10.4 “Overload Characteristics”.
Revision September 2013
conductive
10-3
Chapter 10 Specifications
ASDA-B2
10.2 Specifications of Servo Motors (ECMA Series)
Low Inertia Servo Motors
Model: ECMA Series
C△04
C△06
C△08
C△09
C△10
01
02
04
04
07
07
10
10
20
Rated output power (kW)
0.1
0.2
0.4
0.4
0.75
0.75
1.0
1.0
2.0
Rated torque (N-m) *1
0.32
0.64
1.27
1.27
2.39
2.38
3.18
3.18
6.37
Maximum torque (N-m)
0.96
1.92
3.82
3.82
7.16
7.14
8.78
9.54
19.11
Rated speed (r/min)
3000
Maximum speed (r/min)
5000
3000
5000
Rated current (A)
0.90
1.55
2.60
2.60
5.10
3.66
4.25
7.30
12.05
Maximum current (A)
2.70
4.65
7.80
7.74
15.3
11
12.37
21.9
36.15
Power rating (kW/s)
27.7
(without brake)
Rotor moment of inertia
0.037
2
(× 10-4kg.m ) (without brake)
Mechanical time constant
0.75
(ms) (without brake)
22.4
57.6
22.1
48.4
29.6
38.6
38.1
90.6
0.177
0.277
0.68
1.13
1.93
2.62
2.65
4.45
0.80
0.53
0.73
0.62
1.72
1.20
0.74
0.61
Torque constant-KT (N-m/A)
0.36
0.41
0.49
0.49
0.47
0.65
0.75
0.43
0.53
Voltage constant-KE
(mV/(r/min))
13.6
16.0
17.4
18.5
17.2
27.5
24.2
16.8
19.2
Armature resistance (Ohm)
9.30
2.79
1.55
0.93
0.42
1.34
0.897
0.20
0.13
Armature inductance (mH)
24.0
12.07
6.71
7.39
3.53
7.55
5.7
1.81
1.50
Electrical time constant (ms)
2.58
4.30
4.30
7.96
8.36
5.66
6.35
9.30
11.4
Insulation class
Class A (UL), Class B (CE)
Insulation resistance
>100M, DC 500V
Insulation strength
1500V AC, 60 seconds
Weight (kg) (without brake)
0.5
1.2
1.6
2.1
3.0
2.9
3.8
4.3
6.2
Weight (kg) (with brake)
0.8
1.5
2.0
2.9
3.8
3.69
5.5
4.7
7.2
Max. radial shaft load (N)
78.4
196
196
245
245
245
245
490
490
Max. thrust shaft load (N)
39.2
68
68
98
98
98
98
98
98
25.6
21.3
53.8
22.1
48.4
29.3
37.9
30.4
82.0
0.04
0.192
0.30
0.73
1.18
1.95
2.67
3.33
4.95
0.81
0.85
0.57
0.78
0.65
1.74
1.22
0.93
0.66
0.3
1.3
1.3
2.5
2.5
2.5
2.5
8.0
8.0
7.2
6.5
6.5
8.2
8.2
8.2
8.2
18.5
18.5
Power rating (kW/s)
(with brake)
Rotor moment of inertia
2
(× 10-4kg.m ) (with brake)
Mechanical time constant
(ms) (with brake)
Brake holding torque
[Nt-m (min)]
*2
Brake power consumption
o
(at 20 C) [W]
10-4
Revision September 2013
ASDA-B2
Chapter 10 Specifications
Model: ECMA Series
Brake release time
[ms (Max)]
Brake pull-in time
[ms (Max)]
C△04
C△06
C△08
C△09
C△10
01
02
04
04
07
07
10
10
20
5
10
10
10
10
10
10
10
10
25
70
70
70
70
70
70
70
70
Vibration grade (um)
15
Operating temperature
0 ~ 40 oC
Storage temperature
-10 ~ 80 oC
Operating humidity
20% to 90% RH (non-condensing)
Storage humidity
20% to 90% RH (non-condensing)
Vibration capacity
2.5G
IP rating
IP65 (when waterproof connectors are used, or when an oil seal is used to be
fitted to the rotating shaft (an oil seal model is used))
Approvals
Footnote:
*1
Rate torque values are continuous permissible values at 0~40oC ambient temperature when
attaching with the sizes of heatsinks listed below:
ECMA-__04 / 06 / 08 : 250mm x 250mm x 6mm
ECMA-__10 : 300mm x 300mm x 12mm
ECMA-__13 : 400mm x 400mm x 20mm
ECMA-__18 : 550mm x 550mm x 30mm
Material type : Aluminum – F40, F60, F80, F100, F130, F180
*2
The holding brake is used to hold the motor shaft, not for braking the rotation. Never use it
decelerating or stopping the machine.
*3
For the specifications of the motors with rotary magnetic encoders, please refer to the
specifications of the corresponding standard models.
*4
(△) in the mode of servo motor indicates the type of encoder. △ = 1: increment, 20-bit; △= 2:
increment, 17-bit.
for
NOTE
1) Please refer to Section 1.2 for details about the model explanation.
Revision September 2013
10-5
Chapter 10 Specifications
ASDA-B2
Medium / High Inertia Servo Motors
Model: ECMA Series
Rated output power (kW)
Rated torque (N-m)
*1
Maximum torque (N-m)
E△13
E△18
F△18
G△13
05
10
15
20
20
30
30
03
06
09
0.5
1.0
1.5
2.0
2.0
3.0
3.0
0.3
0.6
0.9
2.39
4.77
7.16
9.55
9.55
14.32
19.10
2.86
5.73
8.59
7.16
14.32
21.48
28.65
28.65
42.97
57.29
8.59
17.19
21.48
Rated speed (r/min)
2000
Maximum speed (r/min)
1500
1000
3000
2000
Rated current (A)
2.9
5.6
8.3
11.01
11.22
16.1
19.4
2.5
4.8
7.5
Maximum current (A)
8.7
16.8
24.81
33.0
33.66
48.3
58.2
7.44
14.49
22.5
7.0
27.1
45.9
62.5
26.3
37.3
66.4
10.0
39.0
66.0
8.17
8.41
11.18
14.59
34.68
54.95
54.95
8.17
8.41
11.18
1.91
1.51
1.11
0.96
1.62
1.06
1.28
1.84
1.40
1.07
0.83
0.85
0.87
0.87
0.85
0.89
0.98
1.15
1.19
1.15
30.9
31.9
31.8
31.8
31.4
32.0
35.0
42.5
43.8
41.6
Armature resistance (Ohm)
0.57
0.47
0.26
0.174
0.119
0.052
0.077
1.06
0.82
0.43
Armature inductance (mH)
7.39
5.99
4.01
2.76
2.84
1.38
1.27
14.29
11.12
6.97
Electrical time constant
(ms)
12.96
12.88
15.31
15.86
23.87
26.39
16.51
13.55
13.55
16.06
Power rating (kW/s)
(without brake)
Rotor moment of inertia
2
(× 10-4kg.m )
Mechanical time constant
(ms)
Torque constant-KT
(N-m/A)
Voltage constant-KE
(mV/(r/min))
Insulation class
Class A (UL), Class B (CE)
Insulation resistance
>100M, DC 500V
Insulation strength
AC 1500V,60 sec
Weight (kg) (without brake)
6.8
7.0
7.5
7.8
13.5
18.5
18.5
6.8
7.0
7.5
Weight (kg) (with brake)
8.2
8.4
8.9
9.2
17.5
22.5
22.5
8.2
8.4
8.9
Max. radial shaft load (N)
490
490
490
490
1176
1470
1470
490
490
490
Max. thrust shaft load (N)
98
98
98
98
490
490
490
98
98
98
6.4
24.9
43.1
59.7
24.1
35.9
63.9
9.2
35.9
62.1
8.94
9.14
11.90
15.88
37.86
57.06
57.06
8.94
9.14
11.9
2.07
1.64
1.19
1.05
1.77
1.10
1.33
2.0
1.51
1.13
10.0
10.0
10.0
10.0
25.0
25.0
25.0
10.0
10.0
10.0
19.0
19.0
19.0
19.0
20.4
20.4
20.4
19.0
19.0
19.0
Power rating (kW/s)
(with brake)
Rotor moment of inertia
2
(× 10-4kg.m ) (with brake)
Mechanical time constant
(ms) (with brake)
Brake holding torque
*2
[Nt-m (min)]
Brake power consumption
o
(at 20 C) [W]
10-6
Revision September 2013
ASDA-B2
Chapter 10 Specifications
Model: ECMA Series
Brake release time
[ms (Max)]
Brake pull-in time
[ms (Max)]
E△13
E△18
F△18
05
10
15
20
20
30
30
03
06
09
10
10
10
10
10
10
10
10
10
10
70
70
70
70
70
70
70
70
70
70
Vibration grade (um)
15
Operating temperature
0 ~ 40 oC
Storage temperature
-10 ~ 80 oC
Operating humidity
20% to 90% RH (non-condensing)
Storage humidity
20% to 90% RH (non-condensing)
Vibration capacity
2.5G
IP rating
G△13
IP65 (when waterproof connectors are used, or when an oil seal is used to be
fitted to the rotating shaft (an oil seal model is used))
Approvals
Footnote:
*1
Rate torque values are continuous permissible values at 0~40oC ambient temperature when
attaching with the sizes of heatsinks listed below:
ECMA-__04 / 06 / 08 : 250mm x 250mm x 6mm
ECMA-__10 : 300mm x 300mm x 12mm
ECMA-__13 : 400mm x 400mm x 20mm
ECMA-__18 : 550mm x 550mm x 30mm
Material type : Aluminum – F40, F60, F80, F100, F130, F180
*2
The holding brake is used to hold the motor shaft, not for braking the rotation. Never use it
decelerating or stopping the machine.
*3
For the specifications of the motors with rotary magnetic encoders, please refer to the
specifications of the corresponding standard models.
*4
(△) in the mode of servo motor indicates the type of encoder. △ = 1: increment, 20-bit; △= 2:
increment, 17-bit.
for
NOTE
1) Please refer to Section 1.2 for details about the model explanation.
Revision September 2013
10-7
Chapter 10 Specifications
ASDA-B2
10.3 Servo Motor Speed-Torque Curves
10-8
Revision September 2013
ASDA-B2
Chapter 10 Specifications
10.4 Overload Characteristics
 Overload Protection Function
Overload protection is a built-in protective function to prevent a motor from overheating.
 Occasion of Overload
1. Motor was operated for several seconds under a torque exceeding 100% torque.
2. Motor had driven high inertia machine and had accelerated and decelerated at high frequency.
3. Motor UVW cable or encoder cable was not connected correctly.
4. Servo gain was not set properly and caused motor hunting.
5. Motor holding brake was not released.
 Chart of load and operating time
Low Inertia Series (ECMA C/CM Series)
Revision September 2013
10-9
Chapter 10 Specifications
ASDA-B2
Medium and Medium-High Inertia Series (ECMA E, F Series)
High Inertia Series (ECMA G/GM Series)
10-10
Revision September 2013
ASDA-B2
Chapter 10 Specifications
10.5 Dimensions of Servo Drives
Order P/N: ASD-B2-0121; ASD-B2-0221; ASD-B2-0421 (100W ~ 400W)
WEIGHT
1.07 (2.36)
NOTE
1)
Dimensions are in millimeters (inches); Weights are in kilograms (kg) and (pounds (lbs)).
2)
Dimensions and weights of the servo drive may be revised without prior notice.
Revision September 2013
10-11
Chapter 10 Specifications
ASDA-B2
Order P/N: ASD-B2-0721 (750W)
WEIGHT
1.54 (3.40)
NOTE
1) Dimensions are in millimeters (inches); Weights are in kilograms (kg) and (pounds (lbs)).
2) Dimensions and weights of the servo drive may be revised without prior notice.
10-12
Revision September 2013
ASDA-B2
Chapter 10 Specifications
Order P/N: ASD-B2-1021;ASD-B2-1521 (1kW ~ 1.5kW)
WEIGHT
1.72 (3.79)
NOTE
1)
Dimensions are in millimeters (inches); Weights are in kilograms (kg) and (pounds (lbs)).
2)
Dimensions and weights of the servo drive may be revised without prior notice.
Revision September 2013
10-13
Chapter 10 Specifications
ASDA-B2
Order P/N: ASD-B2-2023;ASD-B2-3023 (2kW ~ 3kW)
WEIGHT
2.67 (5.88)
NOTE
1) Dimensions are in millimeters (inches); Weights are in kilograms (kg) and (pounds (lbs)).
2) Dimensions and weights of the servo drive may be revised without prior notice.
10-14
Revision September 2013
ASDA-B2
Chapter 10 Specifications
10.6 Dimensions of Servo Motors
Motor Frame Size: 86mm and below Models
Model
C△0401□S
C△0602□S
C△0604□S
C△0804□S
C△0807□S
C△0907□S
C△0910□S
LC
40
60
60
80
80
86
86
LZ
4.5
5.5
5.5
6.6
6.6
6.6
6.6
LA
46
70
70
90
90
100
100
S
8 ( 00 .009 )
14 ( 00 .011 )
14 ( 00 .011 )
14 ( 00 .011 )
19 ( 00 .013 )
16 ( 00 .011 )
16 ( 00 .011 )
LB
30 ( 00 .021 )
50 ( 00 .025 )
50 ( 00 .025 )
70 ( 00 .030 )
70 ( 00 .030 )
80 ( 00 .030 )
80 ( 00 .030 )
LL (without brake)
100.6
105.5
130.7
112.3
138.3
130.2
153.2
LL (with brake)
136.6
141.6
166.8
152.8
178
161.3
184.3
LS (without oil
seal)
20
27
27
27
32
30
30
LS (with oil seal)
20
24
24
24.5
29.5
30
30
LR
25
30
30
30
35
35
35
LE
2.5
3
3
3
3
3
3
LG
5
7.5
7.5
8
8
8
8
LW
16
20
20
20
25
20
20
RH
6.2
11
11
11
15.5
13
13
WK
3
5
5
5
6
5
5
W
3
5
5
5
6
5
5
T
3
M3
Depth 8
5
M4
Depth 15
5
M4
Depth 15
5
M4
Depth 15
6
M6
Depth 20
5
M5
Depth 15
5
M5
Depth 15
TP
NOTE
1) Dimensions are in millimeters.
2) Dimensions and weights of the servo motor may be revised without prior notice.
3) The boxes () in the model names are for optional configurations. (Please refer to section 1.2
model explanation.)
for
4) (△) in the mode of servo motor indicates the type of encoder. △ = 1: increment, 20-bit; △= 2: increment,
17-bit.
Revision September 2013
10-15
Chapter 10 Specifications
5)
ASDA-B2
Except ECMA-CM0604PS LL: 116.2mm, for the specifications of the motors with rotary magnetic
encoders, please refer to the specifications of the corresponding standard models.
Motor Frame Size: 100mm ~ 130mm Models
Model
G△1303□S
E△1305□S
G△1306□S
G△1309□S
C△1010□S
LC
130
130
130
130
100
LZ
9
9
9
9
9
LA
145
145
145
145
115
S
22 ( 00 .013 )
22 ( 00 .013 )
22 ( 00 .013 )
22 ( 00 .013 )
22 ( 00 .013 )
LB
110 ( 00 .035 )
110 ( 00 .035 )
110 ( 00 .035 )
110 ( 00 .035 )
95 ( 00 .035 )
LL (without brake)
147.5
147.5
147.5
163.5
153.3
LL (with brake)
183.5
183.5
183.5
198
192.5
LS
47
47
47
47
37
LR
55
55
55
55
45
LE
6
6
6
6
5
LG
11.5
11.5
11.5
11.5
12
LW
36
36
36
36
32
RH
18
18
18
18
18
WK
8
8
8
8
8
W
8
8
8
8
8
T
7
M6
Depth 20
7
M6
Depth 20
7
M6
Depth 20
7
M6
Depth 20
7
M6
Depth 20
TP
NOTE
1) Dimensions are in millimeters.
2) Dimensions and weights of the servo motor may be revised without prior notice.
3)
The boxes () in the model names are for optional configurations. (Please refer to section 1.2
model explanation.)
for
4) (△) in the mode of servo motor indicates the type of encoder. △ = 1: increment, 20-bit; △= 2: increment,
17-bit.
10-16
Revision September 2013
ASDA-B2
5)
Chapter 10 Specifications
For the specifications of the motors with rotary magnetic encoders, please refer to the specifications of
the corresponding standard models.
Motor Frame Size: 100mm ~ 130mm Models
Model
E△1310□S
E△1315□S
C△1020□S
E△1320□S
LC
130
130
100
130
LZ
9
9
9
9
LA
145
145
115
145
S
22 ( 00 .013 )
22 ( 00 .013 )
22 ( 00 .013 )
22 ( 00 .013 )
LB
110 ( 00 .035 )
110 ( 00 .035 )
95 ( 00 .035 )
110 ( 00 .035 )
LL (without brake)
147.5
167.5
199
187.5
LL (with brake)
183.5
202
226
216
LS
47
47
37
47
LR
55
55
45
55
LE
6
6
5
6
LG
11.5
11.5
12
11.5
LW
36
36
32
36
RH
18
18
18
18
WK
8
8
8
8
W
8
8
8
8
T
7
M6
Depth 20
7
M6
Depth 20
7
M6
Depth 20
7
M6
Depth 20
TP
NOTE
1) Dimensions are in millimeters.
2) Dimensions and weights of the servo motor may be revised without prior notice.
3)
The boxes () in the model names are for optional configurations. (Please refer to section 1.2
model explanation.)
4) ( in the mode of servo motor indicates the type of encoder.
17-bit.
Revision September 2013
= 1: increment, 20-bit;
for
= 2: increment,
10-17
Chapter 10 Specifications
ASDA-B2
Motor Frame Size: 180mm Models
Model
E△1820□S
E△1830□S
F△1830□S
LC
180
180
180
LZ
13.5
13.5
13.5
LA
200
200
200
S
35 ( 00 .016 )
35 ( 00 .016 )
35 ( 00 .016 )
LB
114 .3 ( 00 .035 )
114 .3 ( 00 .035 )
114 .3 ( 00 .035 )
LL (without brake)
169
202.1
202.1
LL (with brake)
203.1
235.3
235.3
LS
73
73
73
LR
79
79
79
LE
4
4
4
LG
20
20
20
LW
63
63
63
RH
30
30
30
WK
10
10
10
W
10
10
10
T
8
M12
Depth 25
8
M12
Depth 25
8
M12
Depth 25
TP
NOTE
1) Dimensions are in millimeters.
2) Dimensions and weights of the servo motor may be revised without prior notice.
3)
The boxes () in the model names are for optional configurations. (Please refer to section 1.2 for model
explanation.)
4) (△) in the mode of servo motor indicates the type of encoder. △ = 1: increment, 20-bit; △= 2: increment,
17-bit.
10-18
Revision September 2013
Appendix A Accessories

Power Connectors
Delta Part Number: ASDBCAPW0000
Title
Part No.
Manufacturer
Housing
C4201H00-2*2PA
JOWLE
Terminal
C4201TOP-2
JOWLE
Delta Part Number:ASDBCAPW0100
Title
Part No.
Manufacturer
Housing
C4201H00-2*3PA
JOWLE
Terminal
C4201TOP-2
JOWLE
Delta Part Number: ASD-CAPW1000
Delta Part Number: ASD-CAPW2000
Revision September 2013
A-1
Appendix A Accessories

ASDA-B2
Power Cables
Delta Part Number: ASDBCAPW0203/0205
Title
Part No.
Manufacturer
Housing
C4201H00-2*2PA
JOWLE
Terminal
C4201TOP-2
JOWLE
Title
Part No.
1
2
L
ASDBCAPW0203
mm
3000  50
inch
118  2
ASDBCAPW0205
5000  50
197  2
Delta Part Number: ASDBCAPW0303/0305
A-2
Title
Part No.
Manufacturer
Housing
C4201H00-2*3PA
JOWLE
Terminal
C4201TOP-2
JOWLE
Title
Part No.
1
2
L
ASDBCAPW0303
mm
3000  50
inch
118  2
ASDBCAPW0305
5000  50
197  2
Revision September 2013
ASDA-B2
Appendix A Accessories
Delta Part Number: ASDBCAPW1203/1205
YF3.5-3SG
3106A-20-18S
L
Title
Part No.
Straight
1
ASDBCAPW1203
2
ASDBCAPW1205
L
3106A-20-18S
mm
3000  50
inch
118  2
3106A-20-18S
5000  50
197  2
Delta Part Number: ASDBCAPW1303/1305
Title
Part No.
Straight
1
ASDBCAPW1303
2
ASDBCAPW1305
L
3106A-20-18S
mm
3000  50
inch
118  2
3106A-20-18S
5000  50
197  2
Delta Part Number: ASD-CAPW2203/2205
L
Title
Part No.
Straight
1
ASD-CAPW2203
3106A-24-11S
mm
3000  50
inch
118  2
2
ASD-CAPW2205
3106A-24-11S
5000  50
197  2
Revision September 2013
A-3
Appendix A Accessories
ASDA-B2
Delta Part Number: ASD-CAPW2303/2305

Title
Part No.
Straight
1
ASD-CAPW2303
2
ASD-CAPW2305
L
3106A-24-11S
mm
3000  50
inch
118  2
3106A-24-11S
5000  50
197  2
Encoder Connectors
Delta Part Number: ASDBCAEN0000
Title
Part No.
Manufacturer
Housing
AMP (1-172161-9)
AMP
Terminal
AMP (170359-3)
AMP
CLAMP
DELTA (34703237XX)
DELTA
Delta Part Number: ASDBCAEN1000
A-4
Revision September 2013
ASDA-B2

Appendix A Accessories
Encoder Cables
Delta Part Number: ASDBCAEN0003/0005
Title
Part No.
Manufacturer
Housing
AMP (1-172161-9)
AMP
Terminal
AMP (170359-3)
AMP
CLAMP
DELTA (34703237XX)
DELTA
Title
Part No.
1
2
L
ASDBCAEN0003
mm
3000  50
inch
118 2
ASDBCAEN0005
5000  50
197  2
Delta Part Number: ASDBCAEN1003/1005
L
Title
Part No.
Straight
1
ASDBCAEN1003
3106A-20-29S
mm
3000  50
inch
118  2
2
ASDBCAEN1005
3106A-20-29S
5000  50
197  2
Revision September 2013
A-5
Appendix A Accessories

ASDA-B2
I/O Signal Connector (CN1)
Delta Part Number: ASDBCNDS0044

Communication Cable between Servo Drive and Computer (for PC)
Delta Part Number: ASD-CNUS0A08
Title
A-6
Part No. : ASD-CNUS0A08
cable
L
connector
RJ connector
USB connector
3000  100 mm
118 4 inch
RJ-45
A-type (USB V2.0)
Revision September 2013
ASDA-B2

Appendix A Accessories
Voltage Output Cable (Analog Signal)
Delta Serial Number: 3864471800
Title
Housing
Terminal

Part No.
A2004H00-3P
A2004TOP-2
Manufacturer
JWT
JWT
RS-485 Connector
Delta Part Number: ASD-CNIE0B06
Revision September 2013
A-7
Appendix A Accessories
ASDA-B2
 Servo Drive, Servo Motor and Accessories Combinations
100W Servo Drive and 100W Low Inertia Servo Motor
Servo Drive
Low inertia
Servo Motor
Motor Power Cable
(Without Brake)
Power Connector
(Without Brake)
Motor Power Cable
(With Brake)
ASD-B2-0121-B
ECMA-C△0401S
ASDBCAPW020X
ASDBCAPW0000
ASDBCAPW030X
Power Connector
(With Brake)
ASDBCAPW0100
Encoder Cable
ASDBCAEN000X
Encoder Connector
ASDBCAEN0000
(X=3 means 3m; X=5 means 5m)
200W Servo Drive and 200W Low Inertia Servo Motor
Servo Drive
Low inertia
Servo Motor
Motor Power Cable
(Without Brake)
Power Connector
(Without Brake)
Motor Power Cable
(With Brake)
ASD-B2-0122-B
ECMA-C△0602S
ASDBCAPW020X
ASDBCAPW0000
ASDBCAPW030X
Power Connector
(With Brake)
ASDBCAPW0100
Encoder Cable
ASDBCAEN000X
Encoder Connector
ASDBCAEN0000
(X=3 means 3m; X=5 means 5m)
400W Servo Drive and 400W Low Inertia Servo Motor
Servo Drive
ASD-B2-0421-B
ECMA-C△0604□S
Low inertia
ECMA-C△0804□7
Servo Motor
ECMA-CM0604PS
Motor Power Cable
(Without Brake)
Power Connector
(Without Brake)
Motor Power Cable
(With Brake)
A-8
ASDBCAPW020X
ASDBCAPW0000
ASDBCAPW030X
Revision September 2013
ASDA-B2
Appendix A Accessories
Power Connector
(With Brake)
ASDBCAPW0100
Encoder Cable
ASDBCAEN000X
Encoder Connector
ASDBCAEN0000
(X=3 means 3m; X=5 means 5m)
400W Servo Drive and 500W Medium Inertia Servo Motor
Servo Drive
ASD-B2-0421-B
Medium inertia
ECMA-E△1305□S
Servo Motor
Motor Power Cable
(Without Brake)
Motor Power Cable
(With Brake)
ASDBCAPW120X
ASDBCAPW130X
Power Connector
ASD-CAPW1000
Increment Encoder Cable
ASDBCAEN100X
Encoder Connector
ASDBCAEN1000
(X=3 means 3m; X=5 means 5m)
400W Servo Drive and 300W High Inertia Servo Motor
Servo Drive
ASD-B2-0421-B
High inertia
ECMA-G△1303□S
Servo Motor
Motor Power Cable
(Without Brake)
Motor Power Cable
(With Brake)
ASDBCAPW120X
ASDBCAPW130X
Power Connector
ASD-CAPW1000
Encoder Cable
ASDBCAEN100X
Encoder Connector
ASDBCAEN1000
(X=3 means 3m; X=5 means 5m)
750W Servo Drive and 750W Low Inertia Servo Motor
Servo Drive
ASD-B2-0721-B
ECMA-C△0807□S
Low inertia
ECMA-C△0907□S
Servo Motor
Motor Power Cable
(Without Brake)
Power Connector
(Without Brake)
Motor Power Cable
(With Brake)
Power Connector
(With Brake)
Revision September 2013
ASDBCAPW020X
ASDBCAPW0000
ASDBCAPW030X
ASDBCAPW0100
A-9
Appendix A Accessories
ASDA-B2
Encoder Cable
ASDBCAEN000X
Encoder Connector
ASDBCAEN0000
(X=3 means 3m; X=5 means 5m)
750W Servo Drive and 600W High Inertia Servo Motor
Servo Drive
ASD-B2-0721-B
ECMA-G△1306□S
High inertia
ECMA-GM1306PS
Servo Motor
Motor Power Cable
(Without Brake)
Motor Power Cable
(With Brake)
ASDBCAPW120X
ASDBCAPW130X
Power Connector
ASD-CAPW1000
Encoder Cable
ASDBCAEN100X
Encoder Connector
ASDBCAEN1000
(X=3 means 3m; X=5 means 5m)
1kW Servo Drive and 1kW Low Inertia Servo Motor
Servo Drive
ASD-B2-1021-B
Low inertia
ECMA-C△1010□S
Servo Motor
Motor Power Cable
(Without Brake)
Motor Power Cable
(With Brake)
ASDBCAPW120X
ASDBCAPW130X
Power Connector
ASD-CAPW1000
Encoder Cable
ASDBCAEN100X
Encoder Connector
ASDBCAEN1000
(X=3 means 3m; X=5 means 5m)
1kW Servo Drive and 1kW Low Inertia Servo Motor
Servo Drive
ASD-B2-1021-B
Low inertia
ECMA-C△0910□S
Servo Motor
Motor Power Cable
(Without Brake)
Power Connector
(Without Brake)
Motor Power Cable
(With Brake)
ASDBCAPW020X
ASDBCAPW0000
ASDBCAPW030X
Power Connector
(With Brake)
ASDBCAPW0100
Encoder Cable
ASDBCAEN000X
Encoder Connector
ASDBCAEN0000
(X=3 means 3m; X=5 means 5m)
A-10
Revision September 2013
ASDA-B2
Appendix A Accessories
1kW Servo Drive and 1kW Medium Inertia Servo Motor
Servo Drive
ASD-B2-1021-B
Medium inertia
ECMA-C△1310□S
Servo Motor
Motor Power Cable
(Without Brake)
Motor Power Cable
(With Brake)
ASDBCAPW120X
ASDBCAPW130X
Power Connector
ASD-CAPW1000
Encoder Cable
ASDBCAEN100X
Encoder Connector
ASDBCAEN1000
(X=3 means 3m; X=5 means 5m)
1kW Servo Drive and 900W High Inertia Servo Motor
Servo Drive
ASD-B2-1021-B
ECMA-G
△1309□S
High Inertia
ECMA-GM1309PS
Servo Motor
Motor Power Cable
(Without Brake)
Motor Power Cable
(With Brake)
ASDBCAPW120X
ASDBCAPW130X
Power Connector
ASD-CAPW1000
Encoder Cable
ASDBCAEN100X
Encoder Connector
ASDBCAEN1000
(X=3 means 3m; X=5 means 5m)
1.5kW Servo Drive and 1.5kW Medium Inertia Servo Motor
Servo Drive
ASD-B2-1521-B
Medium Inertia
ECMA-E△1315□S
Servo Motor
Motor Power Cable
(Without Brake)
Motor Power Cable
(With Brake)
ASDBCAPW120X
ASDBCAPW130X
Power Connector
ASD-CAPW1000
Encoder Cable
ASDBCAEN100X
Encoder Connector
ASDBCAEN1000
(X=3 means 3m; X=5 means 5m)
Revision September 2013
A-11
Appendix A Accessories
ASDA-B2
2kW Servo Drive and 2kW Low Inertia Servo Motor
Servo Drive
ASD-B2-2023-B
Low Inertia
ECMA-C△1020□S
Servo Motor
Motor Power Cable
(Without Brake)
Motor Power Cable
(With Brake)
ASDBCAPW120X
ASDBCAPW130X
Power Connector
ASD-CAPW1000
Encoder Cable
ASDBCAEN100X
Encoder Connector
ASDBCAEN1000
(X=3 means 3m; X=5 means 5m)
2kW Servo Drive and 2kW Medium Inertia Servo Motor
Servo Drive
ASD-B2-2023-B
Medium Inertia
ECMA-E△1320□S
Servo Motor
Motor Power Cable
(Without Brake)
Motor Power Cable
(With Brake)
ASDBCAPW120X
ASDBCAPW130X
Power Connector
ASD-CAPW1000
Encoder Cable
ASDBCAEN100X
Encoder Connector
ASDBCAEN1000
(X=3 means 3m; X=5 means 5m)
2kW Servo Drive and 2kW Medium Inertia Servo Motor
Servo Drive
ASD-B2-2023-B
Medium Inertia
ECMA-E△1820□S
Servo Motor
Motor Power Cable
(Without Brake)
Motor Power Cable
(With Brake)
ASD-CAPW220X
ASD-CAPW230X
Power Connector
ASD-CAPW2000
Encoder Cable
ASDBCAEN100X
Encoder Connector
ASDBCAEN1000
(X=3 means 3m; X=5 means 5m)
A-12
Revision September 2013
ASDA-B2
Appendix A Accessories
3kW Servo Drive and 3kW Medium Inertia Servo Motor
Servo Drive
ASD-B2-3023-B
Medium Inertia
ECMA-E△1830□S
Servo Motor
Motor Power Cable
ASD-CAPW220X
(Without Brake)
Motor Power Cable
(With Brake)
ASD-CAPW230X
Power Connector
ASD-CAPW2000
Encoder Cable
ASDBCAEN100X
Encoder Connector
ASDBCAEN1000
(X=3 means 3m; X=5 means 5m)
3kW Servo Drive and 3kW Medium/High Inertia Servo Motor
Servo Drive
ASD-B2-3023-B
Medium/High Inertia
ECMA-F△1830□S
Servo Motor
Motor Power Cable
ASD-CAPW220X
(Without Brake)
Motor Power Cable
(With Brake)
ASD-CAPW230X
Power Connector
ASD-CAPW2000
Encoder Cable
ASDBCAEN100X
Encoder Connector
ASDBCAEN1000
(X=3 means 3m; X=5 means 5m)
Other Accessories (for ASDA-B2 series all models)
Description
Communication Cable between Servo Drive
and Computer (for PC)
Regenerative Resistor 400W 100Ω
Delta Part Number
Regenerative Resistor 1kW 1000Ω
BR1K0W020
ASD-CARS0003
BR400W040
NOTE
1) () at the ends of the servo drive model names are for optional configurations (Full closed-loop,
CANopen and extension DI port). For the actual model name, please refer to the ordering information of
the actual purchased product.
2) (△) in the model of servo motor indicates the encoder mode. △ =1: increment, 20-bit; △ =2:
increment, 17-bit.
3) () in the servo motor model names are for optional configurations (keyway, brake and oil seal).
Revision September 2013
A-13
Appendix A Accessories
ASDA-B2
(This page is intentionally left blank.)
A-14
Revision September 2013
Appendix B Maintenance and
Inspection
Delta AC servo drives are based on solid state electronics technology. Preventive
maintenance is required to operate this AC servo drives in its optimal condition, and to
ensure a long life. It is recommended to perform a periodic maintenance and inspection of
the AC servo drive by a qualified technician. Before any maintenance and inspection,
always turn off the AC input power to the unit.

Be sure to disconnect AC power and ensure that the internal capacitors have
fully discharged before performing the maintenance and inspection!
Basic Inspection
After power is in connected to the AC servo drive, the charge LED will be lit which
indicates that the AC servo drive is ready.
Item
Content
 Periodically inspect the screws of the servo drive, motor shaft, terminal block
and the connection to mechanical system. Tighten screws as necessary as
they may loosen due to vibration and varying temperatures.
 Ensure that oil, water, metallic particles or any foreign objects do not fall
inside the servo drive, motor, control panel or ventilation slots and holes. As
General Inspection
these will cause damage.
 Ensure the correct installation and the control panel. It should be free from
airborne dust, harmful gases or liquids.
 Ensure that all wiring instructions and recommendations are followed;
otherwise damage to the drive and or motor may result.
 Inspect the servo drive and servo motor to insure they were not damaged.
 To avoid an electric shock, be sure to connect the ground terminal of servo
drive to the ground terminal of control panel.
Inspection before  Before making any connection, wait 10 minutes for capacitors to discharge
after the power is disconnected, alternatively, use an appropriate discharge
operation
device to discharge.
(Control power is
not applied)
 Ensure that all wiring terminals are correctly insulated.
 Ensure that all wiring is correct or damage and or malfunction may result.
 Visually check to ensure that there are not any unused screws, metal strips,
or any conductive or inflammable materials inside the drive.
Revision September 2013
B-1
Appendix B Maintenance and Inspection
Item
ASDA-B2
Content
 Never put inflammable objects on servo drive or close to the external
regenerative resistor.
 Make sure control switch is OFF.
 If the electromagnetic brake is being used, ensure that it is correctly wired.
Inspection before  If required, use an appropriate electrical filter to eliminate noise to the servo
drive.
operation
(Control power is  Ensure that the external applied voltage to the drive is correct and matched
to the controller.
not applied)
Inspection during
operation
(Control power is
applied))
 Ensure that the cables are not damaged, stressed excessively or loaded
heavily. When the motor is running, pay close attention on the connection of
the cables and notice that if they are damaged, frayed or over extended.
 Check for abnormal vibrations and sounds during operation. If the servo
motor is vibrating or there are unusual noises while the motor is running,
please contact the dealer or manufacturer for assistance.
 Ensure that all user-defined parameters are set correctly. Since the
characteristics of various machinery are different, in order to avoid accident
or cause damage, do not adjust the parameter abnormally and ensure the
parameter setting is not an excessive value.
 Ensure to reset some parameters when the servo drive is off (Please refer to
Chapter 7). Otherwise, it may result in malfunction.
 If there is no contact sound or there be any unusual noises when the relay of
the servo drive is operating, please contact your distributor for assistance or
contact with Delta.
 Check for abnormal conditions of the power indicators and LED display. If
there is any abnormal condition of the power indicators and LED display,
please contact your distributor for assistance or contact with Delta.
Maintenance
 Use and store the product in a proper and normal environment.
 Periodically clean the surface and panel of servo drive and motor.
 Make sure the conductors or insulators are corroded and/or damaged.
 Do not disassemble or damage any mechanical part when performing maintenance.
 Clean off any dust and dirt with a vacuum cleaner. Place special emphasis on cleaning
the ventilation ports and PCBs. Always keep these areas clean, as accumulation of
dust and dirt can cause unforeseen failures.
B-2
Revision September 2013
ASDA-B2
Appendix B Maintenance and Inspection
Life of Replacement Components
 Smooth capacitor
The characteristics of smooth capacitor would be deteriorated by ripple current
affection. The life of smooth capacitor varies according to ambient temperature and
operating conditions. The common guaranteed life of smooth capacitor is ten years
when it is properly used in normal air-conditioned environment.
 Relay
The contacts will wear and result in malfunction due to switching current. The life of
relay varies according to power supply capacity. Therefore, the common guaranteed
life of relay is cumulative 100,000 times of power on and power off.
 Cooling fan
The cooling fan life is limited and should be changed periodically. The cooling fan will
reach the end of its life in 2~3 years when it is in continuous operation. However, it
also must be replaced if the cooling fan is vibrating or there are unusual noises.
Revision September 2013
B-3
Appendix B Maintenance and Inspection
ASDA-B2
This page is intentionally left blank.
B-4
Revision September 2013
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement