Millermatic 250 - Miller Welding

OM-1308
144212M
December 1997
Processes
Gas Metal Arc (MIG) Welding
Flux Cored Arc (FCAW)
Welding
Description
Arc Welding Power Source And Wire
Feeder
R
Millermatic 250
Visit our website at
www.MillerWelds.com
TABLE OF CONTENTS
The following terms are
used interchangeably
throughout this manual:
MIG = GMAW
SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3. Additional Symbols for Installation, Operation, and Maintenance . . . . . . . . . . . . . . . . . . . . . .
1-4. Principal Safety Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-5. EMF Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2 – INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1. Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-2. Duty Cycle And Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3. Volt-Ampere Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-4. Installing Work Clamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-5. Installing Welding Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-6. Setting Gun Polarity For Wire Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-7. Installing Gas Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-8. Installing Wire Spool And Adjusting Hub Tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-9. Positioning Jumper Links . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-10. Electrical Service Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-11. Selecting A Location And Connecting Input Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-12. Threading Welding Wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3 – OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1. Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2. Installing Receptacle Module For Use With A Spool Gun (Optional) . . . . . . . . . . . . . . . . . . . .
SECTION 4 – MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-1. Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2. Circuit Breaker CB1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3. Unit Overload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4. Replacing Gun Contact Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-5. Installing Drive Roll And Wire Inlet Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-6. Aligning Drive Rolls And Wire Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7. Unicable Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-8. Cleaning Or Replacing Gun Liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-9. Replacing Switch And/Or Head Tube . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-10. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 5 – ELECTRICAL DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 6 – PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
OPTIONS AND ACCESSORIES
WARRANTY
1
1
1
3
3
4
5
5
5
6
6
7
7
7
8
8
9
9
10
11
11
11
12
12
12
12
13
8
13
13
14
15
16
17
18
SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING
som _nd_5/97
1-1. Symbol Usage
Means Warning! Watch Out! There are possible hazards
with this procedure! The possible hazards are shown in
the adjoining symbols.
Y Marks a special safety message.
. Means “Note”; not safety related.
This group of symbols means Warning! Watch Out! possible
ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards.
Consult symbols and related instructions below for necessary actions
to avoid the hazards.
1-2. Arc Welding Hazards
Y The symbols shown below are used throughout this manual to
call attention to and identify possible hazards. When you see
the symbol, watch out, and follow the related instructions to
avoid the hazard. The safety information given below is only
a summary of the more complete safety information found in
the Safety Standards listed in Section 1-4. Read and follow all
Safety Standards.
D If earth grounding of the workpiece is required, ground it directly
with a separate cable – do not use work clamp or work cable.
Y Only qualified persons should install, operate, maintain, and
repair this unit.
D Wear a safety harness if working above floor level.
D Keep all panels and covers securely in place.
Y During operation, keep everybody, especially children, away.
D Clamp work cable with good metal-to-metal contact to workpiece
or worktable as near the weld as practical.
ELECTRIC SHOCK can kill.
Touching live electrical parts can cause fatal shocks
or severe burns. The electrode and work circuit is
electrically live whenever the output is on. The input
power circuit and machine internal circuits are also
live when power is on. In semiautomatic or automatic wire welding, the
wire, wire reel, drive roll housing, and all metal parts touching the
welding wire are electrically live. Incorrectly installed or improperly
grounded equipment is a hazard.
D Do not touch electrode if you are in contact with the work, ground,
or another electrode from a different machine.
D Use only well-maintained equipment. Repair or replace damaged
parts at once. Maintain unit according to manual.
D Insulate work clamp when not connected to workpiece to prevent
contact with any metal object.
D Do not connect more than one electrode or work cable to any
single weld output terminal.
SIGNIFICANT DC VOLTAGE exists after removal of
input power on inverters.
D Turn Off inverter, disconnect input power, and discharge input
capacitors according to instructions in Maintenance Section
before touching any parts.
D Do not touch live electrical parts.
D Wear dry, hole-free insulating gloves and body protection.
D Insulate yourself from work and ground using dry insulating mats
or covers big enough to prevent any physical contact with the work
or ground.
D Do not use AC output in damp areas, if movement is confined, or if
there is a danger of falling.
D Use AC output ONLY if required for the welding process.
D If AC output is required, use remote output control if present on
unit.
D Disconnect input power or stop engine before installing or
servicing this equipment. Lockout/tagout input power according to
OSHA 29 CFR 1910.147 (see Safety Standards).
D Properly install and ground this equipment according to its
Owner’s Manual and national, state, and local codes.
D Keep your head out of the fumes. Do not breathe the fumes.
D Always verify the supply ground – check and be sure that input
power cord ground wire is properly connected to ground terminal in
disconnect box or that cord plug is connected to a properly
grounded receptacle outlet.
D When making input connections, attach proper grounding conductor first – double-check connections.
D Frequently inspect input power cord for damage or bare wiring –
replace cord immediately if damaged – bare wiring can kill.
D Turn off all equipment when not in use.
D Do not use worn, damaged, undersized, or poorly spliced cables.
D Do not weld in locations near degreasing, cleaning, or spraying operations. The heat and rays of the arc can react with vapors to form
highly toxic and irritating gases.
D Do not drape cables over your body.
FUMES AND GASES can be hazardous.
Welding produces fumes and gases. Breathing
these fumes and gases can be hazardous to your
health.
D If inside, ventilate the area and/or use exhaust at the arc to remove
welding fumes and gases.
D If ventilation is poor, use an approved air-supplied respirator.
D Read the Material Safety Data Sheets (MSDSs) and the
manufacturer’s instructions for metals, consumables, coatings,
cleaners, and degreasers.
D Work in a confined space only if it is well ventilated, or while
wearing an air-supplied respirator. Always have a trained watchperson nearby. Welding fumes and gases can displace air and
lower the oxygen level causing injury or death. Be sure the breathing air is safe.
D Do not weld on coated metals, such as galvanized, lead, or
cadmium plated steel, unless the coating is removed from the weld
area, the area is well ventilated, and if necessary, while wearing an
air-supplied respirator. The coatings and any metals containing
these elements can give off toxic fumes if welded.
OM-1308 Page 1
ARC RAYS can burn eyes and skin.
Arc rays from the welding process produce intense
visible and invisible (ultraviolet and infrared) rays
that can burn eyes and skin. Sparks fly off from the
weld.
D Wear a welding helmet fitted with a proper shade of filter to protect
your face and eyes when welding or watching (see ANSI Z49.1
and Z87.1 listed in Safety Standards).
D Wear approved safety glasses with side shields under your
helmet.
D Use protective screens or barriers to protect others from flash and
glare; warn others not to watch the arc.
D Wear protective clothing made from durable, flame-resistant material (leather and wool) and foot protection.
BUILDUP OF GAS can injure or kill.
D Shut off shielding gas supply when not in use.
D Always ventilate confined spaces or use
approved air-supplied respirator.
HOT PARTS can cause severe burns.
D Do not touch hot parts bare handed.
D Allow cooling period before working on gun or
torch.
MAGNETIC FIELDS can affect pacemakers.
WELDING can cause fire or explosion.
Welding on closed containers, such as tanks,
drums, or pipes, can cause them to blow up. Sparks
can fly off from the welding arc. The flying sparks, hot
workpiece, and hot equipment can cause fires and
burns. Accidental contact of electrode to metal objects can cause
sparks, explosion, overheating, or fire. Check and be sure the area is
safe before doing any welding.
D Protect yourself and others from flying sparks and hot metal.
D Do not weld where flying sparks can strike flammable material.
D Remove all flammables within 35 ft (10.7 m) of the welding arc. If
this is not possible, tightly cover them with approved covers.
D Be alert that welding sparks and hot materials from welding can
easily go through small cracks and openings to adjacent areas.
D Watch for fire, and keep a fire extinguisher nearby.
D Be aware that welding on a ceiling, floor, bulkhead, or partition can
cause fire on the hidden side.
D Do not weld on closed containers such as tanks, drums, or pipes,
unless they are properly prepared according to AWS F4.1 (see
Safety Standards).
D Connect work cable to the work as close to the welding area as
practical to prevent welding current from traveling long, possibly
unknown paths and causing electric shock and fire hazards.
D Do not use welder to thaw frozen pipes.
D Remove stick electrode from holder or cut off welding wire at
contact tip when not in use.
D Wear oil-free protective garments such as leather gloves, heavy
shirt, cuffless trousers, high shoes, and a cap.
D Remove any combustibles, such as a butane lighter or matches,
from your person before doing any welding.
FLYING METAL can injure eyes.
D Welding, chipping, wire brushing, and grinding
cause sparks and flying metal. As welds cool,
they can throw off slag.
D Wear approved safety glasses with side
shields even under your welding helmet.
OM-1308 Page 2
D Pacemaker wearers keep away.
D Wearers should consult their doctor before
going near arc welding, gouging, or spot
welding operations.
NOISE can damage hearing.
Noise from some processes or equipment can
damage hearing.
D Wear approved ear protection if noise level is
high.
CYLINDERS can explode if damaged.
Shielding gas cylinders contain gas under high
pressure. If damaged, a cylinder can explode. Since
gas cylinders are normally part of the welding
process, be sure to treat them carefully.
D Protect compressed gas cylinders from excessive heat, mechanical shocks, slag, open flames, sparks, and arcs.
D Install cylinders in an upright position by securing to a stationary
support or cylinder rack to prevent falling or tipping.
D Keep cylinders away from any welding or other electrical circuits.
D Never drape a welding torch over a gas cylinder.
D Never allow a welding electrode to touch any cylinder.
D Never weld on a pressurized cylinder – explosion will result.
D Use only correct shielding gas cylinders, regulators, hoses, and fittings designed for the specific application; maintain them and
associated parts in good condition.
D Turn face away from valve outlet when opening cylinder valve.
D Keep protective cap in place over valve except when cylinder is in
use or connected for use.
D Read and follow instructions on compressed gas cylinders,
associated equipment, and CGA publication P-1 listed in Safety
Standards.
1-3. Additional Symbols for Installation, Operation, and Maintenance
FIRE OR EXPLOSION hazard.
MOVING PARTS can cause injury.
D Do not install or place unit on, over, or near
combustible surfaces.
D Do not install unit near flammables.
D Do not overload building wiring – be sure power supply system is
properly sized, rated, and protected to handle this unit.
D Keep away from moving parts such as fans.
D Keep all doors, panels, covers, and guards
closed and securely in place.
FALLING UNIT can cause injury.
H.F. RADIATION can cause interference.
D Use lifting eye to lift unit only, NOT running
gear, gas cylinders, or any other accessories.
D Use equipment of adequate capacity to lift and
support unit.
D If using lift forks to move unit, be sure forks are
long enough to extend beyond opposite side of
unit.
D
OVERUSE can cause OVERHEATING
D
D Allow cooling period; follow rated duty cycle.
D Reduce current or reduce duty cycle before
starting to weld again.
D Do not block or filter airflow to unit.
D
D
D High-frequency (H.F.) can interfere with radio
navigation, safety services, computers, and
communications equipment.
D Have only qualified persons familiar with
electronic equipment perform this installation.
The user is responsible for having a qualified electrician promptly correct any interference problem resulting from the installation.
If notified by the FCC about interference, stop using the
equipment at once.
Have the installation regularly checked and maintained.
Keep high-frequency source doors and panels tightly shut, keep
spark gaps at correct setting, and use grounding and shielding to
minimize the possibility of interference.
STATIC (ESD) can damage PC boards.
D Put on grounded wrist strap BEFORE handling
boards or parts.
D Use proper static-proof bags and boxes to
store, move, or ship PC boards.
ARC WELDING can cause interference.
MOVING PARTS can cause injury.
D Keep away from moving parts.
D Keep away from pinch points such as drive
rolls.
D
D
WELDING WIRE can cause injury.
D Do not press gun trigger until instructed to do
so.
D Do not point gun toward any part of the body,
other people, or any metal when threading
welding wire.
D
D
D Electromagnetic energy can interfere with
sensitive electronic equipment such as
computers and computer-driven equipment
such as robots.
D Be sure all equipment in the welding area is
electromagnetically compatible.
To reduce possible interference, keep weld cables as short as
possible, close together, and down low, such as on the floor.
Locate welding operation 100 meters from any sensitive electronic equipment.
Be sure this welding machine is installed and grounded
according to this manual.
If interference still occurs, the user must take extra measures
such as moving the welding machine, using shielded cables,
using line filters, or shielding the work area.
1-4. Principal Safety Standards
Safety in Welding and Cutting, ANSI Standard Z49.1, from American
Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126
Safety and Health Standards, OSHA 29 CFR 1910, from Superintendent of Documents, U.S. Government Printing Office, Washington, D.C.
20402.
Recommended Safe Practices for the Preparation for Welding and Cutting of Containers That Have Held Hazardous Substances, American
Welding Society Standard AWS F4.1, from American Welding Society,
550 N.W. LeJeune Rd, Miami, FL 33126
National Electrical Code, NFPA Standard 70, from National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 1235 Jefferson Davis Highway,
Suite 501, Arlington, VA 22202.
Code for Safety in Welding and Cutting, CSA Standard W117.2, from
Canadian Standards Association, Standards Sales, 178 Rexdale
Boulevard, Rexdale, Ontario, Canada M9W 1R3.
Safe Practices For Occupation And Educational Eye And Face
Protection, ANSI Standard Z87.1, from American National Standards
Institute, 1430 Broadway, New York, NY 10018.
Cutting And Welding Processes, NFPA Standard 51B, from National
Fire Protection Association, Batterymarch Park, Quincy, MA 02269.
OM-1308 Page 3
1-5. EMF Information
Considerations About Welding And The Effects Of Low Frequency
Electric And Magnetic Fields
1. Keep cables close together by twisting or taping them.
Welding current, as it flows through welding cables, will cause electromagnetic fields. There has been and still is some concern about such
fields. However, after examining more than 500 studies spanning 17
years of research, a special blue ribbon committee of the National
Research Council concluded that: “The body of evidence, in the
committee’s judgment, has not demonstrated that exposure to powerfrequency electric and magnetic fields is a human-health hazard.”
However, studies are still going forth and evidence continues to be
examined. Until the final conclusions of the research are reached, you
may wish to minimize your exposure to electromagnetic fields when
welding or cutting.
2. Arrange cables to one side and away from the operator.
To reduce magnetic fields in the workplace, use the following
procedures:
Pacemaker wearers consult your doctor first. If cleared by your doctor,
then following the above procedures is recommended.
OM-1308 Page 4
3. Do not coil or drape cables around your body.
4. Keep welding power source and cables as far away from operator as practical.
5. Connect work clamp to workpiece as close to the weld as possible.
About Pacemakers:
SECTION 2 – INSTALLATION
2-1. Specifications
Max. OpenCircuit
Voltage
Rated Output
250 A at 28 VDC,
40% Duty Cycle
200 A at 28 VDC,
60% Duty Cycle
Amps Input at Rated Output, 50 or 60 Hz, Single-Phase
200 V
220 V
230 V
380 V
415 V
460 V
575 V
KVA
KW
50
2.3*
45
2.2*
44
2*
26
1.3*
24
1.2*
22
1*
18
0.8*
10
0.46*
7.7
0.13*
32
Wire Type and Diameter
Solid Steel
Stainless Steel
Flux Cored
.023 – .045 in
(0.6 – 1.2 mm)
.023 – .035 in
(0.6 – 0.9 mm)
.030 – .045 in
(0.8 – 1.2 mm)
Wire Feed Speed
Dimensions
Net Weight
50–670 IPM
(1.2–1.7 m/min)
H: 37 in (940 mm)
W: 19 in (483 mm)
D: 30-1/4 in (768 mm)
225 lb
(102 kg)
* While idling
2-2. Duty Cycle And Overheating
Duty Cycle is percentage of 10 minutes that unit can weld at rated load
without overheating.
If unit overheats, thermostat(s)
opens, output stops, and cooling
fan runs. Wait fifteen minutes for
unit to cool. Reduce amperage or
voltage, or duty cycle before
welding.
Y Exceeding duty cycle can
damage unit and void
warranty.
60% Duty Cycle At 200 Amperes
6 Minutes Welding
40% Duty Cycle At 250 Amperes
4 Minutes Resting
4 Minutes Welding
6 Minutes Resting
Overheating
A or V
0
15
OR
Reduce Duty Cycle
Minutes
duty1 4/95 – SB-150 215
OM-1308 Page 5
2-3. Volt-Ampere Curves
1
Normal Volt-Ampere Curves
The volt-ampere curves show the
normal minimum and maximum
voltage and amperage output capabilities of the welding power source.
Curves of other settings fall between the curves shown.
1
2
Overload Volt-Ampere Curves
When unit is used beyond capacity,
circuitry senses the overload and
shuts down unit output. Release
trigger and lower weld voltage setting before trying to weld. This shut
down circuitry protects internal
circuits and parts from overload
damage.
60
50
2
DC VOLTS
40
30
*
*
20
10
*Approximate shutdown voltage/amperage
points shown for reference only.
0
0
50
100
150
200
250
300
350
400
DC AMPERES
ssb1.1 10/91 – SB-144 925 / S-0700
2-4. Installing Work Clamp
1
2
Work Cable
Boot
Slide boot onto work cable. Route
cable out front panel opening from
inside.
3
Negative (–) Output Terminal
Connect cable to terminal and
cover connection with boot.
4
4
5
Hardware
Work Clamp
Route cable through clamp handle
and secure as shown.
5
Close door.
1
2
3
Tools Needed:
1/2, 3/4 in
ST-150 228-E
OM-1308 Page 6
2-5. Installing Welding Gun
1
2
3
1
Drive Assembly
Gun Securing Knob
Gun End
Loosen securing knob. Insert gun
end through opening until it bottoms
against drive assembly. Tighten
knob.
2
4
4
Gun Trigger Plug
Insert plug into receptacle, and
tighten threaded collar.
Close door.
3
Ref. ST-150 256-D
2-6. Setting Gun Polarity For Wire Type
. Always read and follow wire manufacturer’s recommended polarity, and see label inside unit by wire drive assembly.
Tools Needed:
3/4 in
2-7. Installing Gas Supply
Obtain gas cylinder and chain to
running gear, wall, or other stationary support so cylinder cannot fall
and break off valve.
1
2
1
Cap
2
Cylinder Valve
Remove cap, stand to side of
valve, and open valve slightly. Gas
flow blows dust and dirt from valve.
Close valve.
3
3
Cylinder
4
Regulator/Flowmeter
Install so face is vertical.
4
5
Regulator/Flowmeter Gas
Hose Connection
6
Welding Power Source Gas
Hose Connection
Argon Gas
1
OR
2
5
7
Connect customer supplied gas
hose between regulator/flowmeter
gas hose connection, and fitting on
rear of welding power source.
7
3
8
9
CO2 Gas
Flow Adjust
Typical flow rate is 20 cfh (cubic
feet per hour). Check wire manufacturer’s recommended flow
rate.
8
CO2 Adapter (Customer Supplied)
9
O-Ring (Customer Supplied)
Install adapter with O-ring between
regulator/flowmeter and CO2
cylinder.
6
Tools Needed:
1-1/8, 5/8 in
Ref. ST-148 265-B / ST-802 028
OM-1308 Page 7
2-8. Installing Wire Spool And Adjusting Hub Tension
Use compression spring with
8 in (200 mm) spools.
When a slight force is needed to turn spool, tension is set.
Tools Needed:
15/16 in
ST-072573-B
2-9. Positioning Jumper Links
Check input voltage available at
site.
1
200 VOLTS
230 VOLTS
Jumper Links Access Door
Open door.
220 VOLTS
2
Jumper Link Label
Check label – only one is on unit.
3
230 VOLTS
460 VOLTS
380 VOLTS
460 VOLTS
575 VOLTS
415 VOLTS
3
Input Voltage Jumper Links
Move jumper links to match input
voltage.
Close and secure access door.
S-144 918-C
1
S-144 916-A
S-144 915-A
2
Tools Needed:
3/8 in
Ref. ST-148 263-C
OM-1308 Page 8
2-10. Electrical Service Guide
Input Voltage
200
220
230
380
415
460
575
Input Amperes At Rated Output
50
45
44
26
24
22
17
Max Recommended Standard Fuse Or Circuit
Breaker Rating In Amperes
80
70
70
40
35
35
25
Min Input Conductor Size In AWG/Kcmil
8
10
10
12
12
10
12
Max Recommended Input Conductor Length
In Feet (Meters)
93 (28)
75 (23)
82 (25)
137 (42)
163 (50)
329 (100)
313 (95)
Min Grounding Conductor Size In AWG/Kcmil
8
10
10
12
12
10
12
Reference: 1996 National Electrical Code (NEC).
S-0092J
2-11. Selecting A Location And Connecting Input Power
Have only qualified persons make
this installation.
1
Rating Label
Supply correct input power.
Y Special installation may be
required where gasoline or
volatile liquids are present –
see NEC Article 511 or CEC
Section 20.
18 in (457 mm)
for airflow
GND/PE
GND/PE
Connect First
1
L1
L2
Size and ratings must comply with applicable codes. Install conductors in
conduit or equivalent into a deenergized line disconnect device.
ST-801 721
OM-1308 Page 9
2-12. Threading Welding Wire
1
2
3
4
5
6
7
4
Wire Spool
Welding Wire
Inlet Wire Guide
Pressure Adjustment Knob
Drive Roll
Outlet Wire Guide
Gun Conduit Cable
Lay gun cable out straight.
7
Tools Needed:
1
2
3
5
6
. Hold wire tightly to keep it
from unraveling.
4 in
(102 mm)
6 in
(150 mm)
Open pressure assembly.
Pull and hold wire; cut off end.
Push wire thru guides into gun;
continue to hold wire.
Tighten
Close and tighten pressure
assembly, and let go of wire.
Remove gun nozzle and contact tip.
Turn On.
WOOD
Press gun trigger until wire
comes out of gun. Reinstall
contact tip and nozzle
OM-1308 Page 10
Feed wire to check drive roll pressure.
Tighten knob enough to prevent slipping.
Cut off wire. Close
and latch door.
Ref. ST-148 261-C / ST-159 218-B / ST-801 083 / S-0627-A
SECTION 3 – OPERATION
3-1. Controls
1
Wire Speed Control
The scale around the control is percent, not wire feed speed.
2
2
Voltage Switch
The scale around the control is
actual voltage.
3
1
Low Range/Full Range Switch
Use Low Range when wire speed is
between 50 and 350 ipm.
4
5
Pilot Light
Power Switch
3
4
5
Ref. ST-148 579-A / Ref. ST-174 835-A
3-2. Installing Receptacle Module For Use With A Spool Gun (Optional)
Remove existing options panel.
1
2
3
2
1
3
Module
Plug PLG9
Plug PLG7
Connect PLG9 to PLG7.
Slide module into upper front panel
where options panel was removed.
Secure with screws.
See Options and Accessories
page at end of manual, or contact
your Factory Authorized Service
Agent for details.
Tools Needed:
ST-801 732
OM-1308 Page 11
SECTION 4 – MAINTENANCE AND TROUBLESHOOTING
4-1. Routine Maintenance
Y Disconnect power before maintaining.
3 Months
Repair or replace
cracked weld cable.
Replace unreadable labels.
Clean and tighten weld terminals.
6 Months
Blow out or vacuum inside. during
heavy service clean monthly.
Remove drive roll and
carrier. Apply light coat
of oil or grease to drive
motor shaft.
OR
4-2. Circuit Breaker CB1
1
Circuit Breaker CB1
If CB1 opens, wire feeding stops.
2
Welding Gun
Check gun liner for blockage or
kinks.
1
3
Wire Drive Assembly
Check for jammed wire, binding
drive gear or misaligned drive rolls.
2
Allow cooling period and reset
breaker. Close door.
3
Ref. ST-148 261-C
4-3. Unit Overload
If unit is used beyond capacity (excessive wire feed, shorted output, etc.), wire feeds but is not energized. Release gun
trigger to reset this condition.
OM-1308 Page 12
4-4. Replacing Gun Contact Tip
Y Turn Off power.
1
2
Nozzle
Contact Tip
Cut off welding wire at contact tip.
Remove nozzle.
Remove contact tip and install new
contact tip. Reinstall nozzle.
2
1
Tools Needed:
ST-149 326-B
4-5. Changing Drive Roll And Wire Inlet Guide
5
3
1
2
2
Securing Screw
Inlet Wire Guide
Loosen screw. Slide tip as close to
drive rolls as possible without touching. Tighten screw.
3
Anti-Wear Guide
Install guide as shown.
1
4
Drive Roll
Install correct drive roll for wire size
and type.
Tools Needed:
5/64 in
5
7/16 in
Turn nut one click to secure drive
roll.
4
Drive Roll Securing Nut
ST-150 227-C
4-6. Aligning Drive Rolls And Wire Guide
Y Turn Off power.
View is from top of drive rolls looking down with pressure assembly
open.
Correct
3
Incorrect
4
2
1
5
1
2
3
4
5
Drive Roll Securing Nut
Drive Roll
Wire Guide
Welding Wire
Drive Gear
Insert screwdriver, and turn screw
in or out until drive roll groove lines
up with wire guide.
Close pressure roll assembly.
Close door.
Tools Needed:
Ref. ST-800 412-A
4-7. Unicable Repair
To repair or replace unicable, order Unicable Clamp Kit, Part Number 172 018.
OM-1308 Page 13
4-8. Cleaning Or Replacing Gun Liner
Tools Needed:
Y Disconnect gun first.
3/8 in
Head tube
Remove nozzle, contact tip,
adapter, and wire outlet guide.
Wire Outlet Guide
3/8 in
Remove liner.
Lay gun cable out straight
before installing new liner.
Blow out gun casing.
To Reassemble Gun:
Insert new liner.
Install and tighten wire outlet guide.
Cut liner off 3/4 in (20 mm) (3/8 in
[9.5 mm] for aluminum) from head
tube.
Install adapter, contact tip, and
nozzle.
Ref. ST-800 797-A
OM-1308 Page 14
4-9. Replacing Switch And/Or Head Tube
Y Disconnect gun first.
3
1
4
2
Remove handle
locking nut.
Secure head
tube in vice.
5
Remove shock washers from front and
rear of head tube.
6
Slide handle.
Remove switch housing. Note: If installing new
switch, push switch lead connectors onto terminal of
new switch (polarity is not important). Install switch
back into handle, and secure with handle locking nut.
If replacing head tube, continue to end of figure.
Loosen jam nut. Remove
from vice and turn head
tube out by hand.
Do not disturb cable connection between
cable connector and connector nut.
7
Install both existing shock washers
to new head tube and hand-tighten
head tube into connector cable.
9
8
Place head tube in vice and tighten
to within 1/8 in (3.2 mm) spacing between connector cable and body.
Remove from vice. Reposition
handle and install switch housing.
Secure with handle locking nut.
Tools Needed:
3/4 in
Ref. ST-800 795-A
OM-1308 Page 15
4-10. Troubleshooting
Trouble
No weld output; wire does not feed.
Remedy
Be sure line disconnect switch is On (see Section 2-11).
Replace building line fuse or reset circuit breaker if open (see Section 2-11).
Reset circuit breaker CB1 (see Section 4-2).
Secure gun trigger connections (see Section 2-5).
Check and replace Power switch if necessary.
Have Factory Authorized Service Agent check all board connections and main control board.
No weld output; wire feeds.
Thermostat TP1 open (overheating). Allow fan to run; the thermostat will close when the unit has cooled
(see Section 2-2).
Connect work clamp to get good metal to metal contact.
Replace contact tip (see Section 4-4).
An overload condition occurred. Release gun trigger (see Section 4-3).
Have Factory Authorized Service Agent check main control board and main rectifier.
Low weld output.
Connect unit to proper input voltage or check for low line voltage (see Section 2-11).
Check input voltage jumper links and correct position if necessary (see Section 2-9).
Have Factory Authorized Service Agent check main control board.
Fan motor does not run.
NOTE: Fan only runs when cooling
is necessary.
Have Factory Authorized Service Agent check fan-on-demand circuit.
Low, high, or erratic wire speed.
Readjust front panel settings (see Section 3-1).
Place Low Range/Full Range switch in correct position (see Section 3-1).
Change to correct size drive rolls (see Section 4-5).
Readjust drive roll pressure (see Section 2-12).
Replace inlet guide, contact tip, and/or liner if necessary (see Sections 4-4, and 4-8).
Check position of input jumper links (see Section 2-9).
Have Factory Authorized Service Agent check main control board.
No wire feed.
Reset circuit breaker CB1 (see Section 4-2).
Turn Wire Speed control to higher setting (see Section 3-1).
Clear obstruction in gun contact tip or liner (see Sections 4-4 and 4-8).
Readjust drive roll pressure (see Section 2-12).
Change to correct size drive rolls (see Section 4-5).
Rethread welding wire (see Section 2-12).
Check gun trigger and leads. Repair or replace gun if necessary.
Have Factory Authorized Service Agent check main control board.
Poor weld bead, or welding
wire is noodle welding.
OM-1308 Page 16
Check polarity setting for type of welding wire being used (see Section 2-6).
SECTION 5 – ELECTRICAL DIAGRAM
SC-175 883-A
Figure 5-1. Circuit Diagram
OM-1308 Page 17
. Hardware is common and
16
15
14
SECTION 6 – PARTS LIST
19
20
Fig 6-3
Fig 6-6
25
1
2
24
3
23
22
4
Fig 6-2
21
6
7
5
8
9
10
Fig 6-5
8
11
7
12
17
13
18
not available unless listed.
ST-801 717
Figure 6-1. Main Assembly
OM–1308 Page 18
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 6-1. Main Assembly
. . . 1 . . . . . . . . . . . 148 597
. . . 2 . . . . . . . . . . . 146 168
. . . 3 . . PLG7 . . 083 526
. . . 4 . . . . . . . . . . . . Fig 6-2
. . . 5 . . . . T1 . . . 174 553
. . . 5 . . . . T1 . . . 174 554
. . . 5 . . . . T1 . . . 174 552
. . . . . . . . . TP3 . . . 121 497
. . . 6 . . . . . . . . . . . 150 387
. . . 7 . . . . . . . . . . . 602 250
. . . 8 . . . . . . . . . . . 186 758
. . . 9 . . . . Z1 . . . 143 892
. . . 9 . . . . Z1 . . . 150 385
. . . 10 . . . . . . . . . . . . Fig 6-5
. . . 11 . . . . . . . . . . . 146 165
. . . 12 . . . . . . . . . . . 089 899
. . . 13 . . . . . . . . . +146 167
. . . . . . . . . . . . . . . . . 146 991
. . . 14 . . . . . . . . . . . 134 464
. . . 15 . . . . . . . . . +170 513
. . . . . . . . . . . . . . . . . 117 860
. . . 16 . . PLG20 . 144 086
. . . . . . . . . . . . . . . . . 039 778
. . . 16 . . . . . . . . . . . 144 085
. . . 17 . . . . . . . . . . . 146 161
. . . 18 . . . . . . . . . . . 052 692
. . . 19 . . . . . . . . . . . 121 614
. . . 20 . . . SR1 . . . 173 713
. . . . . . . . . . . . . . . . . 166 667
. . . . . . . . . . . . . . . . . 173 784
. . . . . . . . . C3,4 . . 031 689
. . . . . . . . . . . . . . . . . 143 818
. . . . . . . . . TP1 . . . 154 243
. . . . . . . . . . . . . . . . . 171 405
. . . . . . . . . . . . . . . . . 143 852
. . . . . . . . . TP2 . . . 154 244
. . . . . . . . . . . . . . . . . 173 714
. . . 21 . . . . . . . . . . . 602 213
. . . 22 . . . . . . . . . . . 008 999
. . . 23 . . . . . . . . . . . 601 871
. . . 24 . . . . . . . . . . . . Fig 6-3
. . . 25 . . . . . . . . . . . 169 596
. . . . . . . . . . . . . . . . . 182 137
. . . . . . . . . . . . . . . . . 144 108
. . . . . . . . . . . . . . . . . 130 750
. . . . . . . . . . . . . . . . . 600 318
. . . COUPLER, rod threaded .312-18 x 1.000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . PANEL, center enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . HOUSING RECEPTACLE & SOCKETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . BAFFLE, center w/components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . TRANSFORMER, pwr main (200/230/460) (consisting of) . . . . . . . . . . . . . . . 1
. . . TRANSFORMER, pwr main (230/460/575) (consisting of) . . . . . . . . . . . . . . . 1
. . . TRANSFORMER, pwr main (220/380/415) (consisting of) . . . . . . . . . . . . . . . 1
. . . . THERMOSTAT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . BAFFLE, air transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . WASHER, flat stl SAE .750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . WHEEL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . STABILIZER, (60Hz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . STABILIZER, (50Hz) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . PANEL, rear w/components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . PANEL, side LH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . LATCH, slide flush mtg hole 1.000 wide x 1.500 lg . . . . . . . . . . . . . . . . . . . . . . 2
. . . PANEL, side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . LABEL, weld parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . LABEL, warning general precautionary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . WRAPPER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . BLANK, snap-in nyl .187mtg hole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . CORD SET, pwr 250V 8-10ga 3/c 600V 12ft (200/230V) . . . . . . . . . . . . . . . . . 1
. . . RECEPTACLE, str 2P3W 50A 250V (200/230V only) . . . . . . . . . . . . . . . . . . . 1
. . . CORD SET, pwr 8-10ga 3/c 600V 12ft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . BASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . AXLE, running gear (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . RING, retaining ext .750 shaft x .085grv depth . . . . . . . . . . . . . . . . . . . . . . . 2
. . . RECTIFIER, SCR main (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . CLAMP, spring thyristor rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . HEAT SINK, rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . CAPACITOR, rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . THYRISTOR, SCR 325A 300V hockey puck . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . THERMOSTAT, NC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . HEAT SINK, rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . FOOT, mtg rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . THERMOSTAT, NO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . CLAMP, thyristor rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . WASHER, lock stl split .375 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . CASTER, plstc swvl 4 in dia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . NUT, stl hex jam .375-16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . PANEL, front w/components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . GUN, 12ft .030-.035 wire (Fig 6-6) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . REGULATOR/FLOWMETER, 10-50 CFH Argon/CO2 . . . . . . . . . . . . . . . . . . . 1
. . . HOSE, gas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . CLAMP, ground 350A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . CABLE, weld cop strd No. 3 (order by ft) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10ft
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-1308 Page 19
. Hardware is common and
not available unless listed.
1
2
3
4
5
6
7
8
9
7
6
34
10
11
33
Fig 6-4
35
32
12
13
14
31
15
30
16
26
18
19
20
25
24
17
29
27
28
21
23
22
ST-148 325-C
Figure 6-2. Baffle, Center w/Components
OM–1308 Page 20
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 6-2. Baffle, Center w/Components (Fig 6-1 Item 4)
. . . 1 . . . . . . . . . . . 058 427
. . . 2 . . . . . . . . . . . 085 980
. . . 3 . . . . . . . . . . . 605 941
. . . 4 . . . . . . . . . . . 057 543
. . . 5 . . . . . . . . . . . 057 971
. . . 6 . . . . . . . . . . . 010 191
. . . 7 . . . . . . . . . . . 058 628
. . . 8 . . . . . . . . . . . 057 745
. . . 9 . . . . . . . . . . . 058 428
. . . 10 . . . . . . . . . . . 177 307
. . . 11 . . . . . . . . . . . 174 813
. . . . . . . . . . . . . . . . . 186 998
. . . 12 . . . . . . . . . . . 082 902
. . . 13 . . . . . . . . . . . 185 643
. . . 14 . . . . C5 . . . 184 584
. . . . . . . . . . . . . . . . . 083 147
. . . . . . . . . . . . . . . . . 187 752
. . . 15 . . . CR1 . . . 006 393
. . . 16 . . . VR1 . . . 149 542
. . . 17 . . . TE1 . . . 143 911
. . . 18 . . . . . . . . . . . 010 913
. . . 19 . . . . . . . . . . . 038 887
. . . 20 . . . . . . . . . . . 083 426
. . . 21 . . . . . . . . . . . 601 835
. . . 22 . . . . . . . . . . . 038 618
. . . 23 . . . . . . . . . . . 010 199
. . . 24 . . . PC1 . . . 184 316
. . . . . . . . PLG3 . . 115 094
. . . . . . . . PLG4 . . 131 052
. . . . . . . . PLG5 . . 131 056
. . . . . . . . PLG6 . . 115 092
. . . 25 . . . . R1 . . . 119 998
. . . 26 . . . . 1T . . . 129 524
. . . 27 . . . C7,8 . . 128 750
. . . 28 . . . POS . . 039 047
. . . 29 . . . NEG . . 039 046
. . . 30 . . . . . . . . . . . 071 971
. . . 31 . . . CB1 . . . 123 745
. . . 32 . . . . . . . . . . . 134 201
. . . 33 . . . . . . . . . +144 933
. . . 34 . . . . . . . . . . . 021 469
. . . 35 . . . . . . . . . . . . Fig 6-4
. . . RING, retaining spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . NUT, stl hex full .625-11 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . WASHER, flat stl .640 ID x 1.000 OD x 14ga thk . . . . . . . . . . . . . . . . . . . . . . .
. . . SPRING, cprsn .845 OD x .091 wire x 1.500 . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . WASHER, flat stl keyed 1.500dia x .125thk . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . WASHER, fbr .656 ID x 1.500 OD x .125thk . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . WASHER, brake stl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . SPRING, cprsn 2.430 OD x .090 wire x 2.500 . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . HUB, spool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . REEL, support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . BAFFLE, center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . CAPACITOR KIT,(consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . STRIP, mtg center capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . STRIP, mtg capacitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . CAPACITOR, elctlt 15000uf 45VDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . GROMMET, scr No. 8/10 panel hole .312sq .500 high . . . . . . . . . . . . . . . . .
. . . . INSULATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . RELAY, encl 24VAC DPDT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . VARISTOR, 75 joule 350VDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . TERMINAL ASSEMBLY, pri 1ph triple voltage (consisting of) . . . . . . . . . . . . .
. . . . WASHER, flat brs .218 ID x .460 OD x .031thk . . . . . . . . . . . . . . . . . . . . . . .
. . . . STUD, pri bd brs 10-32 x 1.375 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . TERMINAL BOARD, pri . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . NUT, brs hex 10-32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . LINK, jumper term bd pri . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . TUBING, stl .275 ID x .048 wall x 1.000 lg . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . CIRCUIT CARD, control main . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . HOUSING PLUG & SOCKETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . HOUSING RECEPTACLE & SOCKETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . HOUSING RECEPTACLE & SOCKETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . HOUSING PLUG & SOCKETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . RESISTOR, WW fxd 300W 5 ohm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . TERMINAL, frict male .250 x .032 3 pair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . CAPACITOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . TERMINAL, pwr output red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . TERMINAL, pwr output black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . COVER, cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . CIRCUIT BREAKER, man reset 1P 4A 250VAC . . . . . . . . . . . . . . . . . . . . . . . .
. . . STAND-OFF SUPPORT, PC card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . DOOR, access chgov . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . LABEL, danger high voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . WIRE DRIVE & GEARS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
1
1
2
2
1
1
1
1
1
1
2
8
6
1
1
1
1
6
6
1
12
2
2
1
1
1
1
1
1
1
2
1
1
1
1
4
1
1
1
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-1308 Page 21
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 6-3. Panel, Front w/Components (Fig 6-1 Item
24)
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
1
2
3
4
5
6
7
8
9
9
10
11
12
13
14
15
16
. . . . . . . . . . . . . 175 840 . . CONTROL PANEL, (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . R4 . . . . . 157 366 . . . . RESISTOR, MF .5W 1.5K ohm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . S2 . . . . . 148 638 . . . . SWITCH, rocker SPDT 4A 250VAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 097 924 . . . . KNOB, pointer 1.625dia x .250 ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . PLATE, indicator upper (order by model and serial number) . . . . . . . . .
. . . . . . . . . . . . . 148 586 . . . . PANEL, front control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . R2,3 . . . . 035 897 . . . . POTENTIOMETER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 143 974 . . HANDLE, running gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . C9 . . . . . 146 158 . . LEAD ASSEMBLY, elect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . C10 . . . . 175 719 . . LEAD ASSEMBLY, elect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . RC1 . . . . 048 282 . . RECEPTACLE w/SOCKETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . S1 . . . . . 128 755 . . SWITCH, tgl DPST 40A 600VAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 174 814 . . PANEL, front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . PLATE, indicator lower (order by model and serial number) . . . . . . . . . . .
. . . . PL1 . . . . 157 958 . . LIGHT, ind white lens 28V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 057 357 . . BUSHING, snap-in nyl .937 ID x 1.125mtg hole . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . 144 127 . . COVER, opening module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. Hardware is common and
1
1
1
2
1
1
2
1
1
1
1
1
1
1
1
2
1
7
not available unless listed.
1
6
8
5
4
2 3
9
10
16
11
15
14
12
13
ST-801 716
Figure 6-3. Panel, Front w/Components
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM–1308 Page 22
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 6-4. Wire Drive And Gears (Fig 6-2 Item 35)
. . . 1 . . . . . . . . . . . 602 009
. . . 2 . . . . . . . . . . . 172 075
. . . 3 . . . . . . . . . . . 166 072
. . . 4 . . . . . . . . . . . 010 224
. . . 5 . . . . . . . . . . . 182 788
. . . 6 . . . . . . . . . . . 085 242
. . . 7 . . . . . . . . . . . 085 244
. . . 8 . . . . . . . . . . . 010 231
. . . 9 . . . . . . . . . . . 085 243
. . . 10 . . . . . . . . . . . 166 071
. . . 11 . . . . . . . . . . . 079 634
. . . 12 . . . . . . . . . . . 151 828
. . . 13 . . . . . . . . . . . 173 616
. . . 14 . . . PM . . . 173 435
. . . 15 . . . . . . . . . . . 079 633
. . . 16 . . . . . . . . . . . 601 966
. . . 17 . . . . . . . . . . . 145 237
. . . 18 . . . . . . . . . . . 604 538
. . . 19 . . . . . . . . . . . 124 778
. . . 20 . . . . . . . . . . . 173 619
. . . 21 . . . . . . . . . . . 174 609
. . . 22 . . . . . . . . . . . 174 610
. . . 23 . . . . . . . . . . . 173 620
. . . . . . . . . . . . . . . . . 045 233
. . . SCREW, .250-20 x 1.25 soc hd gr 8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . CARRIER, drive roll w/components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . SPACER, gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . PIN, spring CS .187 x 1.000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . HOUSING, adapter gun/feeder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . FASTENER, pinned . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . WASHER, cupped stl .328 ID x .812 OD x .125 lip . . . . . . . . . . . . . . . . . . . . . .
. . . SPRING, cprsn .770 OD x .105 wire x 1.225 . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . KNOB, adj tension . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . LEVER, mtg pressure gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . PIN, hinge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . PIN, cotter hair .054 x .750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . COVER, right angle motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . MOTOR, gear 24VDC 122RPM 20:1 ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . FITTING, hose brs barbed M 3/16tbg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . SCREW, .375–16 x 1.25hexhd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . STOP, cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . WASHER, flat stl SAE .312 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . KNOB, plstc T 1.000 lg x .312-18 x 2.000 bar . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . CARRIER, drive roll w/components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . SCREW, M 4–.7 x 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . SCREW, M 6–1.0 x 20 soc hd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . BUSHING, motor mtg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . GUIDE, anti-wear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. Hardware is common and
not available unless listed.
13
9
See Table 6-1 For
Drive Roll & Wire Guide Kits.
8
10
7
11
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
3
1
1
1
1
1
3
3
1
14
12
6
5
4
3
2
1
23
15
22
16
21
17
20
19
18
ST-148 529-C
Figure 6-4. Wire Drive And Gears
*Recommended Spare Parts.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-1308 Page 23
Table 6-1. Drive Roll And Wire Guide Kits
Note
Base selection of drive rolls upon the following recommended usages:
1
2
3
4
5
V-Grooved rolls for hard wire.
U-Grooved rolls for soft and soft shelled cored wires.
U-Cogged rolls for extremely soft shelled wires (usually hard surfacing types).
V-Knurled rolls for hard shelled cored wires.
Drive roll types may be mixed to suit particular requirements (example: V-Knurled roll in combination
with U-Grooved).
Wire Diameter
Drive Roll
Part No.
Type
Inlet
Wire Guide
087 131
087 130
V-Grooved
056 192
079 594
053 695
V-Grooved
056 192
0.9 mm
079 595
053 700
V-Grooved
056 192
1.2 mm
079 596
053 697
V-Grooved
056 193
Fraction
Decimal
Metric
.023/.025 in.
.023/.025 in.
0.6 mm
.030 in.
.030 in.
0.8 mm
.035 in.
.035 in.
.045 in.
.045 in.
Kit No.
Ref. S-0026-B/7-91
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 6-5. Panel, Rear w/Components (Fig 6-1 Item 10)
...
...
...
...
...
...
...
...
...
...
...
...
...
1
2
3
4
5
6
7
8
9
10
11
12
13
. . . . . . . . . . . 134 834
. . . . . . . . . . . 149 332
. . . GS1 . . . 125 785
. . . . . . . . . . . 143 810
. . . . . . . . . . . 169 654
. . . . . . . . . . . 602 387
. . . . . . . . . . . 605 227
. . . . . . . . . . . 044 426
. . . . . . . . . . . 010 493
. . . . . . . . . . . 148 242
. . . FM1 . . . 148 808
. . . . . . . . . . . 148 809
. . . . . . . . . . . 049 399
. . . HOSE, SAE .187 ID x .410 OD (order by ft) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . CLAMP, hose .405-.485clp dia slfttng . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . VALVE, 24VAC 2 way custom port 1/8 orf . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . PANEL, rear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . BRACKET, support tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . CHAIN, weldless 2/0 x 27.000 lg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . NUT, nyl hex jam .750NPST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . CONNECTOR, clamp cable .690/1.070 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . BUSHING, snap-in nyl .625 ID x .875mtg hole . . . . . . . . . . . . . . . . . . . . . . . . .
. . . WINDTUNNEL, 9 in . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . MOTOR, fan 230V 1550RPM .312dia shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . BLADE, fan 9 in 5wg 34deg .309 bore CCW . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . NUT, speed push-on-type .312 stud .625 OD x .456 ID . . . . . . . . . . . . . . . . . .
3ft
2
1
1
1
1
1
1
1
1
1
1
1
5
. Hardware is common and
4
not available unless listed.
6
3
2
1
7
8
9
10
13
11
12
ST-148 327-C
Figure 6-5. Panel, Rear w/Components
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM–1308 Page 24
Item
No.
Part
No.
Description
Quantity
Figure 6-6. M-25 Gun (Fig 6-1 Item 25)
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
...
1
1
1
1
1
1
1
2
2
2
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
. . . ♦169 724
. . . ♦169 725
. . . ♦169 726
. . . ♦169 727
. . . ♦176 238
. . . ♦176 240
. . . ♦176 242
. . . ♦087 299
. . . ♦000 067
. . . ♦000 068
. . . ♦000 069
. . . . . 169 728
. . . . . 169 729
. . . . . 170 467
. . . . . 170 468
. . . . . 169 730
. . . . . 169 731
. . . . . 169 738
. . . . . 169 732
. . . . . 169 733
. . . . . 169 734
. . . . . 172 018
. . . . . 169 735
. . . . . 169 742
. . . . . 169 743
. . . . . 170 469
. . . . . 169 746
1
2
3
. . NOZZLE, slip type .500 orf .125 recess . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . NOZZLE, slip type .625 orf .125 recess . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . NOZZLE, slip type .625 orf flush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . NOZZLE, slip type .625 orf .125 stickout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . NOZZLE, spot flat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . NOZZLE, spot inside corner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . NOZZLE, spot outside corner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . TIP, contact scr .023 wire x 1.125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . TIP, contact scr .030 wire x 1.125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . TIP, contact scr .035 wire x 1.125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . TIP, contact scr .045 wire x 1.125 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . ADAPTER, contact tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . ADAPTER, nozzle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . RING, retaining . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . O-RING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . WASHER, shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . TUBE, head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . NUT, locking handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . NUT, jam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CONNECTOR, cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . NUT, connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . M25 UNICABLE CLAMP KIT, (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . CLIP, compression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . TUBE, support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . CLAMP, inner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . CLAMP, jacket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . CONNECTOR, switch lead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4
5 6
7
1
1
1
1
1
1
1
2
2
2
2
1
1
1
1
1
1
2
2
2
2
2
1
1
1
1
2
. Hardware is common and
8
not available unless listed.
9
10
11
12
14
15
16
24
13*
26
25
22
17
23
19
27
18
20
21
18
9
10
11
12
17
*Includes Item 18
19
20
ST-800 792
Figure 6-6. M-25 Gun
OM-1308 Page 25
Item
No.
Part
No.
Description
Quantity
Figure 6-6. M-25 Gun (Fig 6-1 Item 25) (Continued)
...
...
...
...
...
...
...
...
...
...
...
19
20
21
22
23
24
24
24
25
26
27
. . . . . 169 737
. . . . . 169 741
. . . . . 180 433
. . . . . 173 521
. . . . . 079 974
. . . ♦172 257
. . . ♦172 258
. . . ♦172 259
. . . . . 079 975
. . . . . 169 723
. . . . . 169 739
. . HANDLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . STRAIN RELIEF, cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CABLE, trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . CONNECTOR, feeder (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . O-RING, .500 ID x .103CS rbr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . KIT, liner monocoil .023/.025 wire x 15ft (consisting of) . . . . . . . . . . . . . . . . . . . . . . . .
. . KIT, liner monocoil .030/.035 wire x 15ft (consisting of) . . . . . . . . . . . . . . . . . . . . . . . .
. . KIT, liner monocoil .035/.045 wire x 15ft (consisting of) . . . . . . . . . . . . . . . . . . . . . . . .
. . . . O-RING, .187 ID x .103CS rbr . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . GUIDE, outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . SWITCH, trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2
1
1
2
1
1
1
1
1
1
♦OPTIONAL
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM–1308 Page 26
Effective January 1, 1997
(Equipment with a serial number preface of “KH” or newer)
This limited warranty supersedes all previous Miller warranties and is exclusive with no other
guarantees or warranties expressed or implied.
LIMITED WARRANTY – Subject to the terms and conditions
below, Miller Electric Mfg. Co., Appleton, Wisconsin,
warrants to its original retail purchaser that new Miller
equipment sold after the effective date of this limited warranty
is free of defects in material and workmanship at the time it is
shipped by Miller. THIS WARRANTY IS EXPRESSLY IN
LIEU OF ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED, INCLUDING
THE
WARRANTIES OF
MERCHANTABILITY AND FITNESS.
Within the warranty periods listed below, Miller will repair or
replace any warranted parts or components that fail due to
such defects in material or workmanship. Miller must be
notified in writing within thirty (30) days of such defect or
failure, at which time Miller will provide instructions on the
warranty claim procedures to be followed.
Miller shall honor warranty claims on warranted equipment
listed below in the event of such a failure within the warranty
time periods. All warranty time periods start on the date that
the equipment was delivered to the original retail purchaser,
or one year after the equipment is sent to a North American
distributor or eighteen months after the equipment is sent to
an International distributor.
1.
2.
5 Years Parts – 3 Years Labor
*
Original main power rectifiers
*
Inverters (input and output rectifiers only)
3 Years — Parts and Labor
*
Transformer/Rectifier Power Sources
*
Plasma Arc Cutting Power Sources
*
Semi-Automatic and Automatic Wire Feeders
*
Inverter Power Supplies
Warranty Questions?
*
Intellitig
Call
1-800-4-A-MILLER
for your local
Miller distributor.
*
Robots
*
Engine Driven Welding Generators
(NOTE: Engines are warranted separately by the
engine manufacturer.)
3.
1 Year — Parts and Labor
*
Motor Driven Guns (w/exception of Spoolmate 185)
*
Process Controllers
*
Positioners and Controllers
*
Automatic Motion Devices
*
Orbital Weld Heads
*
IHPS Power Sources
*
Water Coolant Systems
*
HF Units
*
Grids
*
Spot Welders
*
Load Banks
*
SDX Transformers
*
Miller Cyclomatic Equipment
*
Running Gear/Trailers
*
Plasma Cutting Torches (except APT, ZIPCUT &
PLAZCUT Models)
*
Deutz Engines (outside North America)
*
Field Options
(NOTE: Field options are covered under True Blue
for the remaining warranty period of the product they
are installed in, or for a minimum of one year —
whichever is greater.)
4.
6 Months — Batteries
5.
90 Days — Parts and Labor
*
MIG Guns/TIG Torches
*
APT, ZIPCUT & PLAZCUT Model Plasma Cutting
Torches
*
Remote Controls
*
Accessory Kits
*
Replacement Parts (No labor)
*
Spoolmate 185
Miller’s True Blue Limited Warranty shall not apply to:
1.
Items furnished by Miller, but manufactured by others,
such as engines or trade accessories. These items are
covered by the manufacturer’s warranty, if any.
2.
Consumable components; such as contact tips, cutting
nozzles, contactors, brushes, slip rings, relays or parts
that fail due to normal wear.
3.
Equipment that has been modified by any party other
than Miller, or equipment that has been improperly
installed, improperly operated or misused based upon
industry standards, or equipment which has not had
reasonable and necessary maintenance, or equipment
which has been used for operation outside of the
specifications for the equipment.
MILLER PRODUCTS ARE INTENDED FOR PURCHASE
AND USE BY COMMERCIAL/INDUSTRIAL USERS AND
PERSONS TRAINED AND EXPERIENCED IN THE USE
AND MAINTENANCE OF WELDING EQUIPMENT.
In the event of a warranty claim covered by this warranty, the
exclusive remedies shall be, at Miller’s option: (1) repair; or
(2) replacement; or, where authorized in writing by Miller in
appropriate cases, (3) the reasonable cost of repair or
replacement at an authorized Miller service station; or (4)
payment of or credit for the purchase price (less reasonable
depreciation based upon actual use) upon return of the
goods at customer’s risk and expense. Miller’s option of
repair or replacement will be F.O.B., Factory at Appleton,
Wisconsin, or F.O.B. at a Miller authorized service facility as
determined by Miller. Therefore no compensation or
reimbursement for transportation costs of any kind will be
allowed.
TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL MILLER BE LIABLE
FOR DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF
PROFIT), WHETHER BASED ON CONTRACT, TORT OR
ANY OTHER LEGAL THEORY.
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN
AND ANY IMPLIED WARRANTY, GUARANTY OR
REPRESENTATION AS TO PERFORMANCE, AND ANY
REMEDY FOR BREACH OF CONTRACT TORT OR ANY
OTHER LEGAL THEORY WHICH, BUT FOR THIS
PROVISION, MIGHT ARISE BY IMPLICATION,
OPERATION OF LAW, CUSTOM OF TRADE OR COURSE
OF DEALING, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE, WITH RESPECT TO ANY AND ALL
EQUIPMENT FURNISHED BY MILLER IS EXCLUDED
AND DISCLAIMED BY MILLER.
Some states in the U.S.A. do not allow limitations of how long
an implied warranty lasts, or the exclusion of incidental,
indirect, special or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty
provides specific legal rights, and other rights may be
available, but may vary from state to state.
In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated
herein, and to the extent that they may not be waived, the
limitations and exclusions set out above may not apply. This
Limited Warranty provides specific legal rights, and other
rights may be available, but may vary from province to
province.
Owner’s Record
Please complete and retain with your personal records.
Model Name
Serial/Style Number
Purchase Date
(Date which equipment was delivered to original customer.)
Distributor
Address
City
State
Zip
Resources Available
Always provide Model Name and Serial/Style Number.
Contact your Distributor for:
To locate distributor nearest you call
1-800-4-A-Miller.
Welding Supplies and Consumables
Options and Accessories
Personal Safety Equipment
Service and Repair
Miller Electric Mfg. Co.
Replacement Parts
An Illinois Tool Works Company
1635 West Spencer Street
Appleton, WI 54914 USA
Training (Schools, Videos, Books)
Owner’s Manuals
Technical Manuals (Servicing Information
and Parts)
Circuit Diagrams
Welding Process Handbooks
Contact the Delivering Carrier
for:
File a claim for loss or damage during shipment.
For assistance in filing or settling claims,
contact your distributor and/or equipment
manufacturer’s Transportation Department.
PRINTED IN USA
 1997 Miller Electric Mfg. Co.
International Headquarters–USA
Phone: 920-734-9821
USA & Canada FAX: 920-735-4134
International FAX: 920-735-4125
European Headquarters –
United Kingdom
Phone: 44 (0) 1625-525556
FAX: 44 (0) 1625-537553
Download PDF