PS Series
PS210 Subwoofer
SERVICE MANUAL
Infinity Systems, Inc.
250 Crossways Park Dr.
Woodbury, New York 11797
Rev1 8/2007
PS series PS210 subwoofer
- CONTENTS -
BASIC SPECIFICATIONS
…………………..……………..1
DETAILED SPECIFICATIONS…………………..……….…..2
PACKAGING……………….……………………….…....….…4
CONTROLS AND CONNECTIONS…………..…….………..5
OPERATION….……………………………………………..….7
EXPLODED VIEW/PARTS LIST
…………….….…....……8
TEST SET UP AND PROCEDURE………………..…....……9
BLOCK DIAGRAM…………………………..………….…..…10
ELECTRICAL PARTS LIST (120v) ………………………….11
PCB DRAWINGS……………….……………………………..14
SEMICONDUCTOR PINOUTS……….……………….……..16
SCHEMATICS (120v)………………………………………...17
Basic Specifications
PS210 Powered Subwoofer
Frequency Response:
27Hz – 150Hz (±3dB)
Maximum Amplifier Output:
300 Watts RMS; 500 Watts Peak
(20Hz – 150Hz with no more than 0.1% THD)
Crossover Frequencies:
50Hz – 150Hz, 24dB/octave, continuously variable
Driver:
10" (254mm) MMD®
Dimensions (H x W x D):
(with grille)
15-3/4" x 12-1/2" x 16-1/2"
(400mm x 318mm x 419mm)
Weight:
38.6 lb (17.6kg)
Infinity continually strives to update and improve existing products, as well as create new ones. The specifications
and construction details in this and related Infinity publications are therefore subject to change without notice.
1
PS series PS210 subwoofer
Primus PS210
LINE VOLTAGE
US 120vac/60Hz
EU 230vac/50-60Hz
150W Powered Sub Amp
Yes/No
Yes
Yes
Hi/Lo Line
108-132
207-253
Nom.
120
230
Specification
Unit
QA Test
Limits
Amp Section
Type (Class AB, D, o her)
Load Impedance (speaker)
Rated Output Power (120VAC)
Rated Output Power (230VAC)
D
4
150
150
n/a
Ohms
Watts
Watts
n/a
n/a
145
AVG RMS Dynamic Power
210
Watts
200
THD @ Rated Power
THD @ 1 Watt
DC Offset
0.5
0.2
10
%
%
mV-DC
1
0.3
30
22K filter
22K filter
Sub amp output
Damping factor
>50
DF
35
Measured at amplifier board
Input Sensitivity-120V
Input Frequency
L&R
LFE input
System Gain
50
9.5
9.5
46.72
Hz
mVrms
mVrms
dB
50
Nominal Freq.
±1dB
To 1 Watt
±1dB
To 1 Watt
Reference
Single input driven
Single input driven, LFE switch ON
Single input driven Normal mode
Input Sensitivity-230V
Input Frequency
L&R
LFE input
System Gain
50
TBD
TBD
TBD
Hz
mVrms
mVrms
dB
50
Nominal Freq.
±1dB
To 1 Watt
±1dB
To 1 Watt
Reference
Single input driven
Single input driven, LFE switch ON
Single input driven Normal mode
Signal to Noise
SNR-A-Weighted
SNR-unweighted
SNR rel. 1W-unweighted
90
80
-57
dBA
dBr
dBr
85
75
-55
Residual Noise Floor
1.5
mVrms(max)
2.5
Input Impedance
Line Input (L, R,LFE)
10K
ohms
n/a
50-150
Hz
± 10
Parameter
Unit
Vrms
Vrms
Notes
Normal Operation
Normal operation, MOMS required
Conditions
Notes
Nominal
Domestic version only 120 VAC-60 Hz
EU Version only 230 VAC-50-60 Hz
Average RMS power, 3/20 Cycles 50 Hz, Driven
6dB above its input sensi ivity sensitivity,
average of the first 4 consecutive peaks
relative to rated power
relative to rated power
relative to 1W Output
Volume @max, w/ A/P Swept
Bandpass Measurement (Line
freq.+ harmonics) (BW=20 KHz)
Measured at the speaker cable. 150 Watts @
THD < 0.1 % @ 50 Hz
A-Weighting filter
22K filter
22K filter
Line level inputs must be terminated using
1KOHM
Nominal
Filters
LP filter Variable
Subsonic filter (HPF) 2rd Order
Friend circuit
LFE Low pass
2nd order variable + 2nd order fix-24 db/Octave
Fixed
Fixed
200>LP<500
Hz
Limiter
THD at Max. Output Power
N/A
N/A
functional Maximum Output Power
Maximum THD as a result of limiting.
Features
Volume pot Taper (lin/log)
Phase switch
LP Filter defeat switch
-LOG
0-180
YES
-deg
functional
functional
functional
A Taper
Input Configuration
Line In (L,R) & LFE
YES
--
functional
Dual RCA jack
Signal Sensing (ATO)
Auto-Turn-On (yes/no)
ATO Input test frequency
ATO Level LFE Input
YES
50
2.5
Hz
mV
functional
functional
functional
Maximum acceptable level.
Amp connected and AC on, then
functional
input signal applied
T before muting, after signal is
5-15
removed
Auto turn of time (T) must be 5 > T < 15
Minutes
ATO Turn-on time
12dB/Octave F=31Hz, Q=2
60Hz, Q=2, Av=-3.9dB
LFE input driven only
Disables LP filter, intended for LFE
5
ms
5-15
minutes
3
sec.
4
AC Power Applied
ATO Transient
0.5
V-peak
0.5V
@ Sub amp output
Turn-on Transient
0.5
V-peak
0.8V
@ Sub amp output
Auto Mute/ Turn-OFF Time
Power on Delay time
Transients/Pops
2
Amplifier ac ivated by signal presence at the
Line input
AC Line cycled from OFF to ON
PS series PS210 subwoofer
Specification
Unit
QA Test
Limits
Turn-off Transient
0.5
V-peak
0.8V
Efficiency
Efficiency
Efficiency at 1/8 of rated power
Off state input power
60
38
16
%
%
Watts
58
37
18
Test conducted at rated power 150WNominal Line voltage
Test conducted at 18.75 WRMS
Nominal Line voltage-Rated impedance 4 Ohms
Nominal Line voltage RED LED
Stand-by Input Power
24
Watts
26
@ nom. line voltage
Maximum allowable input power under nominal
Input voltage and frequency, HOT or COLD
operation.LED GREEN no signal applied
Power Cons. @ rated power
250
Watts
260
@ nom. line voltage
150 Watts @ 4 Ohms nominal line voltage
Parameter
Conditions
@ Sub amp output
Notes
AC Line cycled from ON to OFF
Protections
Short Circuit Protection
YES
Thermal Protection
YES
DC Offset Protection
YES
Line Fuse Rating
USA-Domestic
EU
Amplifier should resume opera ion after short
circuit condition removal
Temperature rise in accessible metal parts
@1/8 max unclipped Power at 1.06 should not exceed 35K rise for domestic version
functional
times the input voltage
or 30K rise for European versions (refer to
requirements sheet).
Design must insure no Offset at the speaker
DC present at Speaker Out leads
output under any operating condition including
abnormal operation
functional Direct short at output
2
Amps
2
1.25
Amps
1.25
Type-T or Slo Blo-250 V
Type-T or Slo Blo-250 V, Low
Breaking capacity
3
Internal fuse with UL/SEMKO rated holder
Internal fuse with UL/SEMKO rated holder
PS series PS210 subwoofer
4
PS series PS210 subwoofer
CONTROLS AND CONNECTIONS
Rear Panel
¡ Subwoofer-Level Control
™ LFE/Normal Selector
¶
¡
£ Phase Switch
LEVEL
Green: On
Red: Standby
¢ Crossover Adjustment
Max
Min
LFE
PHASE
NORMAL
0º
180º
™
∞ Line-Level/LFE Input
£
§ Power Switch
80Hz
¶ Status LED
CROSSOVER
FREQUENCY
¢
150Hz
50Hz
L
∞
R
LINE LEVEL IN
For LFE use L or R
ON
OFF
§
POWER
120V
60Hz
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRICAL
SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE
NRTL/C
CSA 22 2
UL1492
AVERTISSEMENT: POUR PRÉVEN R LES RISQUES D'INCEND E OU DE CHOC
ÉLECTRIQUE ÉVITER D EXPOSER CET APPARE L A LA PLUIE OU A L HUMID TÉ
5
PS series PS210 subwoofer
SYSTEM CONNECTIONS
If you have a Dolby® Digital or
DTS® receiver/processor with a
low-frequency effects (LFE) or
subwoofer output:
SUBWOOFER OR
LFE OUTPUT
LEVEL
Green: On
Red: Standby
Max
Min
LFE
PHASE
Set LFE/Normal switch to “LFE.”
NORMAL
0º
180º
80Hz
CROSSOVER
FREQUENCY
150Hz
50Hz
L
R
LINE LEVEL IN
For LFE use L or R
If your receiver/processor does
not contain a Dolby Digital or
DTS processor but has
subwoofer outputs:
LEVEL
Green: On
Red: Standby
Max
Min
LFE
PHASE
L
R
NORMAL
0º
180º
80Hz
CROSSOVER
FREQUENCY
150Hz
50Hz
L
Set line-level/LFE switch to
“Normal.”
R
LINE LEVEL IN
For LFE use L or R
NOTE: If your receiver/processor
has only one sub out, you may use
either the L or R input.
6
PS series PS210 subwoofer
OPERATION
Crossover Adjustment
Power On
The Crossover Adjustment Control ¢ determines the highest frequency at
which the subwoofer reproduces sounds. If your main speakers can comfortably reproduce some low-frequency sounds, set this control to a lower
frequency setting, between 50Hz and 100Hz.This will concentrate the
subwoofer’s efforts on the ultradeep bass sounds required by today’s
films and music. If you are using smaller bookshelf speakers that do
not extend to the lower bass frequencies, set the Crossover Adjustment
control to a higher setting, between 120Hz and 150Hz.
Plug your subwoofer’s AC cord into a wall outlet. Do not use the outlets on
the back of the receiver.
Initially set the Subwoofer-Level Control ¡ to the “min” position.
Turn on your sub by pressing the Power Switch § on the rear panel.Turn
on your entire audio system and start a CD or movie soundtrack at a
moderate level.
Auto On/Standby
NOTE: This control will have no effect if the LFE/Normal Selector ™ is set
to LFE. If you have a Do by Digital or DTS processor/receiver, the Low-Pass
Frequency is set by the processor/receiver. Consult your owner’s manual
to learn how to view or change this setting.
With the Power Switch § in the ON position, the Status LED ¶ on
the back panel will remain lit in red or green to indicate the
On/Standby mode of the subwoofer.
RED = STANDBY (No signal detected, Amp Off)
GREEN = ON (Signal detected, Amp On)
The subwoofer will automatically enter the Standby mode after approximately 10 minutes when no signal is detected from your system.The
subwoofer will then power ON instantly when a signal is detected. During
periods of normal use, the Power Switch § can be left on.You may turn
off the Power Switch § for extended periods of nonoperation, e.g., when
you are away on vacation.
Adjust Gain
Turn your Subwoofer-Level Control ¡ up to the halfway position. If no
sound emanates from the subwoofer, check the AC-line cord and input
cables. Are the connectors on the cables making proper contact? Is the
AC plug connected to a “live” receptacle? Has the Power Switch §
been pressed to the “On” position? Once you have confirmed that the
subwoofer is active, proceed by playing a CD, record or cassette.
Use a selection that has ample bass information.
Set the overall volume control of the preamplifier or stereo to a comfortable level. Adjust the Subwoofer-Level Control ¡ until you obtain a
pleasing blend of bass. Bass response should not overpower the room
but rather be adjusted so there is a harmonious blend across the entire
musical range. Many users have a tendency to set the subwoofer volume
too loud, adhering to the belief that a subwoofer is there to produce lots
of bass.This is not entirely true. A subwoofer is there to enhance bass,
extending the response of the entire system so the bass can be felt as
well as heard. However, overall balance must be maintained or the music
will not sound natural. An experienced listener will set the volume of
the subwoofer so its impact on bass response is always there but is
never obtrusive.
Phase Control
The Phase Switch £ determines whether the subwoofer speaker’s
piston-like action moves in and out with the main speakers, 0˚, or opposite
the main speakers, 180˚. Proper phase adjustment depends on several
variables such as room size, subwoofer placement and listener position.
Adjust the phase switch to maximize bass output at the listening position.
7
PS series PS210 subwoofer
8
PS series PS210 subwoofer
PS210 sub Test Set Up and Procedure
SYSTEM AURAL SWEEP TEST
Equipment needed:
• Function/signal generator/sweep generator
• Integrated Amplifier
• Multimeter
• Speaker cables
General Unit Function (UUT = Unit Under Test)
Switches/knobs on the amplifier faceplate:
Crossover Frequency Adjust full CW (Max)
Phase switch – either position
Normal/LFE switch - Normal
1. From the signal generator, Connect both right and left line level inputs (RCA jacks) – to signal generator and
UUT. Use Y-cable if necessary from mono source.
2. On the amplifier, turn the LEVEL control full Counterclockwise (Min).
3. Turn on generator, adjust to 75mV, 50 Hz.
4. Plug in UUT; turn the power switch ON. Turn LEVEL control full Clockwise (Max).
5. LED (on amp panel) should now be Green; immediate bass response should be heard and felt from rear port
tube opening.
Sweep Function
1. Follow steps 1-5 above, using a sweep generator as a signal source.
2. Sweep generator from 20Hz to 1kHz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or
any other noises. If any unusual noises are heard, remove woofer and test.
Driver Function (Woofer)
1. Remove woofer from cabinet; detach + and - wire clips.
2. Check DC resistance of woofer; it should be 3.4 ohms±10%.
3. Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated
amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.
4. Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
9
PS series PS210 subwoofer
10
PS series PS210 subwoofer
PS210 Electrical Parts List
Part number
Reference Designator
Qty Description
PREMAP/MAIN/POWER PCB
Capacitors
034-330525-300ZR 1 GR Electrolytic cap. 33uF/25V M (R)0511 P:5
033-680464-270ZS 1 GS NPE Cap. 印ELYTONE 6u8/100V K10 (R)1020 GNE
032-100484-200ZS 1 GS END Mylar cap. 1uF/250V K P:15
033-470464-270ZS 1 GS NPE Cap.(印ELYTONE)1K 4u7/100V K10 (R)1015 GNE
031-100343-100ZS 1 GS SMD Cap. 100pF/50V J 0805 NPO
034-220525-301ZS 2 GS Electrolytic cap. 22uF/25V M (R)5x11 P:5
031-560243-100ZS 2 GS SMD Cap. 56pF/50V J 0805 NPO
031-220243-103AZ 1 GS SMD Cap. 0u022/50V J 0805 X7R
031-100344-100ZS 17 GS SMD Cap. 0u1/50V K 0805 X7R
031-100244-100ZS 4 GS SMD Ceramic cap. 0u01/50V K 0805 X7R
034-470515-307ZR 1 GR Electrolytic cap.LOW ESR 85℃ 47uF/16V M (R)0511 P:5
031-100344-100ZS 1 GS SMD Cap. 0u1/50V K 0805 X7R
034-100625-300ZS 1 GS Electrolytic cap. 100uF/25V M (R)6.3x11 P:5
031-470244-102ZS 2 GS SMD Cap. 0u047/50V K 0805 X7R
031-560343-102ZS 1 GS SMD Cap. 560pF/50V J 0805 NPO
034-330615-300ZS 1 GS Electrolytic cap. 330uF/16V M (R)0812 P:5
031-100344-100AZ 2 GS SMD Cap. 0u1/50V K 0805 X7R
035-100393-301ZR 2 GR Mylar cap.(ESK TYPE) 0u1/63V J P:5 PN:ESK063S10JT
035-220393-300ZR 1 GR PE Cap. 0u22/63V J P:5
034-470415-301ZS 1 GS Elect. Cap. 4u7/50V M (R)0511 P:5
034-100525-300ZS 3 GS Electrolytic cap. 10uF/25V M (R)0511 P:5
031-100244-100ZS 2 GS SMD Ceramic cap. 0u01/50V K 0805 X7R
031-100343-100ZS 2 GS SMD Cap. 100pF/50V J 0805 NPO
031-100344-100ZS 1 GS SMD Cap. 0u1/50V K 0805 X7R
031-100384-100RZ 2 GS SMD Cap. 0u1/250V K 1206 X7R
031-220243-103AZ 1 GS SMD Cap. 0u022/50V J 0805 X7R
031-220344-100ZS 5 GS SMD Cap. 220pF/50V J 0805 NPO
031-330244-100ZR 1 GR SMD Cap. 0u033/50V K 0805 X7R
031-680444-102ZR 2 GR SMD Cap. 6800pF/50V K X7R 0805
032-270343-301ZS 3 GS Mylar cap. (MP) 0u27/63V J P:5
032-820244-200ZR 1 GR Mylar cap. 0u082/100V K (R)
034-220515-302ZR 2 GR elect. Cap. 22uF/16V M (R)0511 P:5
034-220525-301ZS 4 GS 22uF/25V M (R)5x11 P:5
034-330615-300ZS 1 GS 330uF/16V M (R)0812 P:5
034-330780-300ZR 2 GR 85℃ SNAPIN 3300uF/80V M (R)22x48
034-470515-200ZR 1 GR 47uF/16V M (R)0511 P:2.5
039-100384-100ZR 1 GR Safety cap. (0u1/250V) .1K275VACx2 18x6x12mm
034-100615-301ZS 1 GS electrolytic cap. 100uF/16V M (R)0611 P:5
031-100344-100ZS 2 GS SMD Capacitor 0u1/50V K 0805 X7R
031-100444-104ZR 1 GR SMD Capacitor 1000pF/50V K 0805 X7R
C1
C72
C70,
C73
C58
C50,53
C57,61
C84,
C42-44,46-49,52,55,60,63,71,74,77,100,101,80
C45,51,66,67,
C65
C54
C64
C62,59
C56
C78
C81,82
C28,2A,
C27,
C2
C35,237,238,
C5,10
C16,36
C11
C3,7
C40
C14,15,20,21,19
C33,
C32,34,
C29,26,25
C30
C39,75
C4,9,41,76
C12
C6,8
C37
CXAC1
C83
C102,103,
C104
Resistors
024-100398-120ZR
020-220497-120ZR
024-100298-120ZR
021-100401-120ZR
024-470498-120ZR
022-500003-020ZR
024-220798-120ZR
024-430498-120ZR
024-300498-120LZ
024-470598-120ZR
024-220598-120ZR
024-680498-120ZR
024-110598-100ZR
024-200598-120ZR
024-100698-120ZR
1
1
2
1
2
1
1
1
1
1
1
6
1
1
2
GR SMD Resistor 100R 1/8W J 0805
GR Carbon Resistor 2K2 1/4W J
GR SMD Resistor 10R 1/8W J 0805
GR MOF Resistor 1K 1W J INK MO-100
GR SMD Resistor 4K7 1/8W J 0805
GR Resistor KNP 0R05 3WS J FK TYPE
GR SMD Resistor 2M2 1/8W J 0805
GR SMD 4K3 1/8W J 0805
GR SMD 3K 1/8W J 0805
GR SMD 47K 1/8W J 0805
GR SMD 22K 1/8W J 0805
GR SMD 6K8 1/8W J 0805
GR SMD 11K 1/8W F 0805
GR SMD 20K 1/8W J 0805
GR SMD 100K 1/8W J 0805
R62
R11
R81,82
R103
R85,86
R104
R80
R78
R105,
R107
R118,
R91
R98
R94
R3,112
R2,74,75,84,88,89,97,106,113-117,119,120,
141,138,139,
024-100598-120ZR 18 GR SMD 10K 1/8W J 0805
11
PS series PS210 subwoofer
Part number
Reference Designator
Qty Description
PREMAP/MAIN/POWER PCB
024-100498-120ZR 7 GR SMD 1K 1/8W J 0805
024-590498-100ZR 1 GR SMD 5K9 1/8W F 0805
024-270498-120ZR 1 GR SMD 2K7 1/8W J 0805
024-442498-100ZR 1 GR SMD 4K42 1/8W F 0805
024-200498-120ZR 1 GR SMD 2K 1/8W J 0805
024-300598-120ZR 1 GR SMD 30K 1/8W J 0805
024-150598-100ZR 2 GR SMD 15K 1/8W F 0805
024-470698-120ZR 2 GR SMD 470K 1/8W J 0805
024-390598-120ZR 1 GR SMD 39K 1/8W J 0805
024-470298-120ZR 2 GR SMD 47R 1/8W J 0805
024-390498-120ZR 1 GR SMD 3K9 1/8W J 0805
024-220398-120ZR 1 GR SMD 220R 1/8W J 0805
024-470398-120ZR 3 GR SMD 470R 1/8W J 0805
024-330498-100ZR 2 GR SMD 3K3 1/8W F 0805
024-220498-121ZR 2 GR SMD 2K2 1/8W J 0805
024-162598-100ZR 4 GR SMD 16K2 1/8W F 0805
024-000098-120ZR 1 GR SMD Resistor 0R 1/8W J 0805
024-100498-120ZR 3 GR SMD Resistor 1K 1/8W J 0805
024-100598-100ZR 5 GR SMD 10K 1/8W F 0805
024-100598-120ZR 11 GR SMD 10K 1/8W J 0805
024-100898-120ZR 1 GR SMD 10M 1/8W J 0805
024-130498-100ZR 1 GR SMD 1K3 1/8W F 0805
024-150498-120ZR 1 GR SMD 1K5 1/8W J 0805
024-150598-100ZR 3 GR SMD 15K 1/8W F 0805
024-160698-120ZR 1 GR SMD 160K 1/8W J 0805
024-220498-121ZR 2 GR SMD 2K2 1/8W J 0805
024-237598-120ZR 1 GR SMD 23K7 1/8W F 0805
024-243498-100ZR 1 GR SMD 2K43 1/8W F 0805
024-270498-120ZR 1 GR SMD 2K7 1/8W J 0805
024-300598-120ZR 1 GR SMD 30K 1/8W J 0805
024-330498-120ZR 8 GR SMD 3K3 1/8W J 0805
024-330598-120ZR 2 GR SMD 33K 1/8W J 0805
024-332498-100ZR 2 GR SMD 3K32 1/8W F 0805
024-470498-121ZR 3 GR SMD 4K7 1/4W J 1206
024-470598-120ZR 2 GR SMD 47K 1/8W J 0805
024-470698-120ZR 1 GR SMD 470K 1/8W J 0805
024-470798-120ZR 1 GR SMD 4M7 1/8W J 0805
024-475498-100ZR 1 GR SMD 4K75 1/8W F 0805
024-511398-100ZR 1 GR SMD 511R 1/8W F 0805
024-560598-120ZR 1 GR SMD 56K 1/8W J 0805
024-619498-100ZR 2 GR SMD 6K19 1/8W F 0805
024-619598-100ZR 1 GR SMD 61K9 1/8W F 0805
024-620398-100ZR 2 GR SMD 620R 1/8W F 0805
024-680498-120ZR 5 GR SMD 6K8 1/8W J 0805
024-680598-120ZR 1 GR SMD 68K 1/8W J 0805
024-681598-100ZR 2 GR SMD 68K1 1/8W F 0805
024-750398-101ZR 1 GR SMD 750R 1/8W F 0805 TPAING
024-750498-100ZR 1 GR SMD 7K5 1/8W F 0805
024-750598-100ZR 1 GR SMD 75K 1/8W F 0805
024-820598-120ZR 2 GR SMD 82K 1/8W J 0805
026-200595-269ZS 1 GS VR PN:RD163121R03D-20KBx2(EJ) FREQUENCY
026-500495-005ZS 1 GS VR 5K PN:RD163111R22B-5K15A-EJ LEVEL
024-100598-120ZR 2 GR SMD Resistor 10K 1/8W J 0805
024-270598-120ZR 1 GR SMD Resistor 27K 1/8W J 0805
R79,83,92,95,96,110,145,
R140,
R73
R128
R108
R131,
R132,133,
R129,130,
R77
R101,102
R93
R90
R76,99,100
R127,137,
R1,87,
R125,126,135,136,
R68
R65,44,151,
R146,147,30,31,33,
R17,19,,54,58,63,71,72,111,123,124,134,
R121
R5A
R67
R29,
R152,
R61,57,
R48
R36
R64
R56,
R7,8,12-15,59,55,
R4,5
R26,27
R148-150,
R47,49
R70,
R60
R38
R6A
R122
R51,53
R4A
R16,18
R46,40-43
R66,
R50,52,
R2A
R35A
R45
R69,39,
VR2
VR1
R142,144
R143
Semiconductors
054-033904-100ZR
054-055500-100ZR
054-033906-100ZR
051-640001-000ZR
054-033904-100ZR
051-222200-100ZR
051-000600-100ZR
1
1
3
2
4
1
1
GR SMD (TRANSISTOR) PN:MMBT3904LT1G SOT23 (O
GR SMD IC: PN:NE555DR S08 (TI) TMER
GR SMD Transistor (ON) PN:MMBT3906LT1G SOT23
GR MOSFET N-Channel PN:IRF640NPBF TO-220 (IR)
GR SMD (TRANSISTOR) PN:MMBT3904LT1G SOT23 (O
GR Transistor NPN (ON SEM) PN:MPS2222ARLRAR TO-92
GR Transistor NPN PN:MPSW06RLRA TO-92 (ON)
12
Q28
U10
Q10,12,15
Q18,22
Q11,14,13,27
Q21
Q16
PS series PS210 subwoofer
Part number
Reference Designator
Qty Description
PREMAP/MAIN/POWER PCB
054-540100-100ZR 3 GR SMD Transistor PNP (ON SEN) MMBT5401 LT1 SOT-23
051-555100-000ZR 1 GR Transistor NPN PN:2N5551 TO-92
051-290700-100ZR 2 GR Transistor PNP (ON) PN:MPS2907A RLRAR TO-92
051-540101-000ZR 1 GR Transistor PNP(FAIRCHILD PN:2N5401 TO-92
054-414803-100ZS 13 GS SMD DIODE: PN:LL4148 MINI-MELF
054-008409-000ZR 1 GR SMD ZENER DIODE: PN:BZX84C3V0-7-F SOT-23
054-008406-000ZR 1 GR SMD ZENER DIODE:PN:BZX84C10-7-F SOT-23
054-008408-000ZR 2 GR SMD ZENER DIODE: PN:BZX84C5V6-7-F SOT-23
054-000100-100ZR 4 GR GS SMD DIODE: PN:ES1D 200V 1A (PANJIT)
054-007200-100ZR 3 GR SMD IC PN:TL072CDR SO-8 (TI) DUAL OP-AMP
053-211100-000ZR 1 GR IC:DIP,PN:IR2111 8PIN (IR) HALF-BRIDGE DRIVER
051-011100-100ZR 1 GR JFET N-Channel PN:J111 TO-92 (FAIRCHILD
054-000100-100ZR 1 GR GS SMD DIODE: PN:ES1D 200V 1A (PANJIT)
054-007200-100ZR 4 GR SMD IC PN:TL072CDR SO-8 (TI)
054-007400-100ZR 2 GR SMD IC:(OP) PN:TL074CDR (TI)
054-008407-000ZR 3 GR SMD ZENER DIODE: PN:BZX84C15-7-F SOT-23
054-011400-100ZR 1 GR SMD Transistor PN:DTC114TKA SMT3 (ROHM
054-033904-100ZR 4 GR SMD (TRANSISTOR) PN:MMBT3904LT1G SOT23 (O
054-033906-100ZR 1 GR SMD Transistor (ON) PN:MMBT3906LT1G SOT23
054-045580-100ZS 1 GS SMD IC:(OP) PN:NJM4558M-TE3- DUAL OP-AMP
054-414803-100ZS 15 GS SMD DIODE: PN:LL4148 MINI-MELF
054-524201-100ZR 1 GS SMD ZENER DIODE: PN:MMBZ5242B 12V SOT-23
054-540100-100ZR 2 GR SMD Transistor PNP (ON SEN) MMBT5401 LT1 SOT-23
051-024100-000ZR 1 GR Transistor DIP PN:MJE241 TO-126 (CENTRAL) NPN
051-025100-000ZR 1 GR Transistor DIP PN:MJE251 TO-126 (CENTRAL) PNP
052-400080-000ZR 1 GR Bridge Rectifier PN:RS804 400V,8A
051-003100-000ZS 1 GS Transistor NPN PN:TIP 31C TO-220 (MOSPEC)
050-505200-001ZS 1 GS LED PN:LT-2402-21
Q20
Q17
Q19,23
Q1
D1,2,27,31,34,44,40-43,46,47,45,
D25
D35
D36,37
D5,26,29,33
U6,8,1,
U7
Q200
D38
U5
U2,3
D6,7,9
Q7
Q5,8,25,9
Q6,
U4
D3,4,8,30,39,11,14,16,17,20,22,18,19,28,32,
D206,
Q24,26
Q2
Q3
BR1
Q4
Miscellaneous/Mechanical
025-010300-000ZR
074-300018-000ZR
043-560200-000ZR
043-300101-000ZR
043-700101-000ZR
041-115001-000ZR
044-100100-000ZR
074-020018-000ZR
093-105202-300ZR
093-205001-320ZR
042-010053-003ZR
042-018600-000ZR
061-020000-000ZS
061-314002-000ZS
061-400014-000BZ
061-700044-000ZR
063-010012-000ZR
063-321101-000ZR
063-531808-000ZR
073-011006-400ZR
073-032315-601ZS
082-022607-000BZ
086-021818-005ZR
086-021820-001ZR
043-000051-000ZR
043-324300-000ZR
072-010305-000ZS
072-040169-000ZR
073-050001-000ZS
074-030002-000ZR
072-040720-000ZR
1
1
1
1
1
1
2
1
1
1
1
1
2
2
4
3
4
1
1
1
1
1
1
1
1
1
1
1
2
2
1
GR Thermister PN:NTSE103KZ072 K L:50mm
GR RELAY PN:943-1C-48D
GR INDUCTOR 56uH YT-10779
GR INDUCTOR PN:YT-10033 30uH
GR TOROIDAL INDUCTOR 70uH YT-10682
GR BEAD COIL PN:YT-10911
GR SMD FERRITE BEAD PN:321611 600R/100MHz 1206
GR ROCKER SW (POWER) PN:RF1003-BB4-0
GR FUSE:UL GSL(2AG) FUSE:2A,250V,5*20mm 120V
GR FUSE: VBS UTE1.25A,250V,5*20mm 230V
GR Transformer YT-10616-4 for 120V
GR Transformer YT-10913 for 230V
GS Knob ABS HTS-10/20 φ20x15m/m UL94V-0 BLK
GS Strain Relief PN:SB4F-2
GR RUBBER FOOT ID:6.2 OD:11.5 t:2mm 55 BLK
GR Mica 13x18mm TO-220
GR Bracket for Transistor P/N:TRK-1
GR Panel 322x105.7x15mm BLK ABS-94V0
GR bucket (PB-10/12) ABS 322x105.7x146.5mm BLK (94VO)
GR BRACKET 16x34mm t:0.8mm
GS Heatsink black anodized 70x58x20mm
GR Wire set #26 UL1007 L:74mm 2P HOUSING
GR Power Cord NISPT-2 18AWGx2 L:1830mm 105C+T187
GRPower cord L:2.0M H05VV-F2x0.75WS019+002E for 230V
GR COIL PN:YT-53015
GR INDUCTOR 324uH YT-10778
GS RCA JACK PN:B217BK 2P INPUT
GR CONNECTOR PN:JS-1001-2 2P P:2.5mm
GS FUSE CLIP P/N:CT-FH1206
GR TOGGLE SW PN:L101-T2B4QE LFE, PHASE
GR HEADER Right Angle PN:JS-1109R-04(S1)
13
TH1,
K1
L1
L2
L3
L5
FB1,FB2
F1 (120V)
F1 (230V)
(120V)
(230V)
LEVEL, FREQUENCY
for Transformer
PCB
CON3B1,
(120V)
(230V)
L6
L4
CONN1
CON3A1
SW5,SW6
CAM350 V 8.0.6 : Thu Mar 08 13:50:59 2007 - (Untitled)
PS series PS210 subwoofer
14
CAM350 V 8.0.6 : Thu Mar 08 13:47:26 2007 - (Untitled)
PS series PS210 subwoofer
15
PS series PS210 subwoofer
16
1
PS series PS210 subwoofer
2
3
01
02
New design
陳宗志 丁明松 李婉慧 游進源
17
PS series PS210 subwoofer
01
02
New design
陳宗志 丁明松 李婉慧 游進源
18