Input/Output Modules - Notifier Fire Systems

Input/Output Modules
Data Sheet
The wide range of input and output modules available from
NOTIFIER delivers exceptional flexibility to a NOTIFIER fire
detection and alarm system. Using these modules enables
integration with a host of other building management and
emergency systems, including access control systems, lifts, fire
shutters and emergency lighting.
Features
• Analogue addressable communications using Opal digital
protocol
• Backward compatible with legacy Notifier systems
• Built-in type identification automatically identifies these
devices to the control panel
Installation
There are 4 enclosures designed to accept these modules.
These are details in the pages following. The single and dual
input/output modules can also be mounted using either panel
mount or DIN rail mount kits for maximum flexibility when
interfacing with third party equipment.
• Stable communication technique with high noise immunity
• Rotary DECADE 01 to 99 or 01 to 159 (for Opal digital
protocol modules) address switches
• Common mounting options including Surface Mount, Panel
Mount and DIN Rail Mount.
• Tri-colour LED’s
• Powered directly by 2‑wire loop. No additional power
required - Option to use external power in sounder driving
applications
• Plug-in terminal connections for ease of field wiring
• Approved to CEA GEI 1-082 AND CEA GEI 1-084
• CPD approval to EN54-17 and EN54-18, LPCB and VdS
This document is not intended to be used for installation purposes. Every care has been taken in the preparation of this document but no liability
can be accepted for the use of the information therein. Design features may be changed or amended without prior notice.
For more information, contact:
NOTIFIER. Charles Avenue, Burgess Hill, West Sussex, RH15 9UF. United Kingdom
Phone: +44 (0) 1444 230 300 Fax: +44 (0) 1444 230 888
Page 1 of 14 - 990-153_0713
ISO9001
Design, Manufacture and
Supply to Quality Management Systems Certified to
ISO9001:1994
www.notifierfiresystems.co.uk
M710 Single input module
The M700 series modules are designed for use with any NOTIFIER protocol fire alarm control panel and include
selectable loop isolation in every device.
The M710 module monitors a single input device circuit of normally open dry contact alarm activation devices.
These modules use one of 99 available module addresses on a loop and respond to regular polls from the
control panel reporting its type and the status (open/normal/short) of its supervised device circuit.
Specifications
M710 Single input module
Mechanical Specification
Electrical Specification
• Dimensions:
Height:
Width:
Depth: 90 mm
92 mm
23 mm
• Weight: 90g
• Maximum Wire Gauge for Terminals 1.5mm2
92mm
• Current Consumption
Without communication
Communication every 5 sec.
with LED blink enabled.
Maximum Alarm Current: • Operating Voltage:
310 µA @ 24 VDC;
510 µA @ 24 VDC
5 mA @ 24 VDC
(per LED with LED enabled)
15 to 30 VDC peak
90mm
Environmental Specifications
• Relative humidity:
0% to 95%, non-condensing
m
m
23mm
Connection Detail
50
m
m
50
-20°C to +60°C
180mm
SMB6-V0
• Operating temperature 245mm
M200E-SMB
134mm
M200E-DIN
M200E-PMB
40mm
139mm
Page 2 of 14 - 990-153_0713
www.notifierfiresystems.co.uk
Non- Addressable Zone Monitor Module M710-CZR
The M710-CZR non-addressable zone monitor module allows a zone of non-addressable detectors to
communicate with a Notifier analogue addressable system. As a result existing nonaddressable loops can be
integrated into a Notifier addressable system
The module monitors a zone of two-wire non-addressable smoke detectors. Each M710-CZR uses one of 99
available module addresses on a loop. The non-addressable zone can be powered from the analogue communication
line or from an external power supply. Where the non-addressable zone is powered from an external power supply,
the communication line is fully isolated from the nonaddressable zone and from the power supply.
This M710-CZR non-addressable Zone Monitor module fits into M200E-SMB, M200E-DIN or M200E-PMB.
These may then be installed in a 19” Rack Assembly using Notifier 19” Rack mounting adapters.
Specifications
Non- Addressable Zone Monitor Module M710-CZR
Mechanical Specification
Electrical Specification
• Dimensions:
Height:
Width:
Depth: 93 mm
83 mm
23 mm
• Weight: 110 g
• Max Standby current 500uA @ 24V
(communication every 5s with LED blink
enabled, with external supply for nonaddressable zone)
• Maximum Wire Gauge for Terminals 2.5mm2
83mm
93mm
• Max Standby current 6.7mA @ 24V
(communication every 5s with LED blink
enabled, loop powered non-addressable
zone, R.EOL only)
• LED Current @ 24Vdc
Red:2.2μA Green: 6.6μA Yellow:8.8μA
• Max non-addressable
zone current limit 60mA
• External power supply voltage 12 – 28.5V
• Maximum series resistance
50Ω
• End of Line Resistor Value: 3.9k
• Temperature Range: -20°C to +60°C
• Humidity: 5% to 95% relative humidity
(non-condensing)
50
50
m
m
m
m
23mm
Environmental Specifications
180mm
SMB6-V0
245mm
M200E-SMB
134mm
M200E-DIN
M200E-PMB
40mm
139mm
Page 3 of 14 - 990-153_0713
www.notifierfiresystems.co.uk
M701 Single output module
The M700 series modules are designed for use with any NOTIFIER protocol fire alarm control panel and include
selectable loop isolation in every device.
The M701 control module provides a monitored single output circuit for use with polarised loads (sounder circuit)
which requires a suitable power source (7Vdc - 30Vdc) for the connected load. Alternatively the same device may
be placed in to an unsupervised mode which can then be used to control any switched load up to 2A @ 30Vdc.
These modules use one of 99 available module addresses on a loop and respond to regular polls from the
control panel reporting its type and the status (open/normal/short) of its supervised device circuit.
Specifications
M701 single output module
Mechanical Specification
• Dimensions:
Height:
Width:
Depth: • Weight: 92mm
Electrical Specification
• Current Consumption
(Without communication) 90 mm
92 mm
23 mm
102g
310 µA @ 24 VDC
• Current Consumption (Communication every 5 sec.
with LED blink enabled)
510 µA @ 24 VDC
• Maximum Alarm Current: 5 mA @ 24 VDC
(per LED with LED enabled)
• Operating Voltage:
15 to 30 VDC peak
90mm
Environmental Specifications
• Operating temperature -20°C to +60°C
• Relative humidity:
0% to 95%, non-condensing
Connection Detail
SMB6-V0
m
m
50
180mm
50
m
m
23mm
WITH SUPERVISED OUTPUT
245mm
M200E-DIN
M200E-SMB
134mm
WITH UNSUPERVISED OUTPUT
M200E-PMB
40mm
139mm
Page 4 of 14 - 990-153_0713
www.notifierfiresystems.co.uk
M701-240 & M701-240-DIN Mains Switching Output Modules
The M701–240 is a loop-powered device controlling an unsupervised double pole (one normally open, one
normally closed) output suitable for managing 240VAC loads. The output relay is a bistable device, latching in the
on or off state on command from the control panel. The module is supplied in a wall mounting box as standard
with a grounding terminal provided.
The M701–240–DIN has the same features and capabilities as the M701–240 but is designed to mount directly
on to a standard 35mm ‘Top Hat’ DIN rail. The module is supplied unboxed for installation in a suitable enclosure.
Each module has built-in short circuit protection for the communications loop; however, to increase application
flexibility, the isolators can be selected/deselected on an individual module basis.
Specifications
M701-240 & M701-240-DIN Mains Switching Output Modules
Mechanical Specification M701-240
Electrical Specification
• Dimensions:
Height:
Width:
Depth: 40 mm
134 mm
139 mm
• Weight
195g
• Maximum Wire Gauge for Terminals 1.5mm2
Mechanical Specification M701-240-DIN
• Dimensions:
Height:
Width:
Depth: 48 mm
125 mm
76 mm
• Weight
140g
• Current Consumption
(Without communication) 275 µA @ 24 VDC
• Current Consumption
(Communication every 5 sec.
with LED blink enabled)
445 µA @ 24 VDC
• Maximum Alarm Current: 5 mA @ 24 VDC
(per LED with LED enabled)
• Operating Voltage:
15 to 30 VDC peak
• Relay Specifications
5A at 30VDC,
5A at 250VAC, resistive load
1 x NO and 1 x NC contacts
• Maximum Wire Gauge for Terminals 2.5mm2
Environmental Specifications
125mm
• Operating temperature -20°C to +60°C
• Relative humidity:
0% to 95%, non-condensing
Connection Detail
48mm
76mm
M701-240-DIN
139mm
40mm
134mm
M701-240
Page 5 of 14 - 990-153_0713
www.notifierfiresystems.co.uk
M720 Dual Input Module
The M700 series modules are designed for use with any NOTIFIER protocol fire alarm control panel and include
selectable loop isolation in every device.
The M720 dual monitor module provides two supervised input device circuits of normally open dry contact alarm
activation devices.
The M720 module uses two addresses of 99 available module addresses on a loop and responds to regular polls
from the control panel reporting its type and the status (open/normal/short) of their supervised device circuits.
Specifications
M720 Dual Input Module
Mechanical Specification
Electrical Specification
• Dimensions:
Height:
Width:
Depth: 90 mm
92 mm
23 mm
• Weight: 90g
• Current Consumption
Without communication
Communication every 5 sec.
with LED blink enabled.
Maximum Alarm Current: 92mm
• Operating Voltage:
340 µA @ 24 VDC;
600 µA @ 24 VDC
5 mA @ 24 VDC
(per LED with LED enabled)
15 to 30 VDC peak
90mm
Environmental Specifications
• Operating temperature -20°C to +60°C
• Relative humidity:
0% to 95%, non-condensing
23mm
Connection Detail
180mm
50
50
m
m
m
m
SMB6-V0
245mm
M200E-SMB
134mm
M200E-DIN
M200E-PMB
40mm
139mm
Page 6 of 14 - 990-153_0713
www.notifierfiresystems.co.uk
M721 Dual Input Module with Output
The M700 series modules are designed for use with any NOTIFIER protocol fire alarm control panel and include
selectable loop isolation in every device.
The M721 dual input, single relay output module, as well as providing two supervised inputs also provides a
single change over relay output rated at 2A @30Vdc.
The M721 uses three addresses of 99 available module addresses on a loop and responds to regular polls from
the control panel reporting its type and the status (open/normal/short) of their supervised device circuits.
Specifications
M721 Dual Input Module with Output
Mechanical Specification
Electrical Specification
• Dimensions:
Height:
Width:
Depth: 90 mm
92 mm
23 mm
• Weight: 102g
• Current Consumption
Without communication
Communication every 5 sec.
with LED blink enabled.
Maximum Alarm Current: 92mm
• Operating Voltage:
340 µA @ 24 VDC;
660 µA @ 24 VDC
5 mA @ 24 VDC
(per LED with LED enabled)
15 to 30 VDC peak
90mm
Environmental Specifications
• Operating temperature -20°C to +60°C
• Relative humidity:
0% to 95%, non-condensing
23mm
Connection Detail
180mm
50
50
m
m
m
m
SMB6-V0
245mm
M200E-SMB
134mm
M200E-DIN
M200E-PMB
40mm
139mm
Page 7 of 14 - 990-153_0713
www.notifierfiresystems.co.uk
NFX-MM1M Mini Module
The NFX-MM1M is an addressable input module. It will interface with contact devices such as security contacts,
sprinkler flow switches and call points. It monitors the cable in the same way as a non-addressable zone, using
an end of line resistor on a two wire circuit.
In addition to transmitting the supervised state of the monitored device (normal, open, or short), the full analogue
supervision measurement is sent back to the panel.
The compact size allows it to fit inside devices or junction boxes behind devices. Its size and light weight allows it
to be installed without the need to be rigidly mounted.
Specifications
NFX-MM1M Mini Module
Mechanical Specification
Electrical Specification
• Dimensions:
Height:
Width:
Depth: 33 mm
71mm
15 mm
• Weight: 57 g
• Operating Voltage:
15 to 32 VDC
• Supervisory Loop Current (normal) 87-114 uA
• Standby Current for comm line 7V
• Nominal Standby Current 110 uA
• End-of-Line Resistance 47 kohm
Environmental Specifications
• Operating temperature 0°C to +49°C
• Relative humidity:
10% to 93%, non-condensing
15m
33mm
71 mm
Page 8 of 14 - 990-153_0713
www.notifierfiresystems.co.uk
Six Channel Output Module NFXI-RM6
The six channel output module is designed for use in applications where numerous single modules are required.
The monitor and control module can be used to supervise and activate sounders, strobes, door closers, break
glass call points, waterflow switches and other ancillary devices.
The NFXI-RM6 consists of six changeover relays. A single isolated set of dry relay contacts, which can be wired
as normally open or normally closed, is provided for each address. The module enables the control panel to
switch contacts on demand. The controlled circuit is not supervised.
In Opal Digital Protocol only one address is used for the entire multimodule with sub-addresses completing the
remaining addresses. For compatibility with existing installations using Notifier CLIP Protocol, the first address
is set from 01 to 94; the other modules are automatically assigned the next five addresses; up to four unused
addresses can be disabled by dip switch.
Specifications
Six Channel Output Module NFXI-RM6
Mechanical Specification
Electrical Specification
• Dimensions:
Height:
Width:
Depth: 25 mm
173 mm
147 mm
• Weight 0.5 kg (package included)
• Wire Gauge for Terminals
Maximum Minimum 3.25 mm2 (12 AWG)
0.8 mm2 (18 AWG)
Features
• Uses Opal protocol (up to 159 addresses)
• Individual Tri-colors LED indicators
• Controllable Isolation
• Maximum Standby Current 1450 uA
• Maximum Alarm Current (red LED) 5 mA
• Relay current (max) 50mA
• Relay Contact Ratings 3A @ 30 VDC,
0.25A @ 250 VAC at 23 °C
• Operating Voltage Range 15-32 VDC
• Maximum Wiring Resistance 40 ohm
Environmental Specifications
• Operating Temperature -10°C to +55°C
• Operating Humidity Range:
10% to 93% RH
• Unused addresses may be disabled
• Rotary address switches
• Class B operation
Connection Detail
• Removable plug–in terminal blocks
• Complies with EN54-17 and EN54-18
Mounting Detail
The multiple input and output modules are PCB Boards and need to be
mounted in suitable metal enclosures.
M200–SMB–MM Surface mounting metal box. Dimensions H 280 x W 229 x D 64mm
Page 9 of 14 - 990-153_0713
www.notifierfiresystems.co.uk
Ten Channel Input Module NFXI-MM10
The NFXI-MM10 provides an interface with normally open contact devices. The supervised state: normal, open
circuit fault or short circuit alarm is sent back to the control panel.
In Opal Digital Protocol only one address is used for the entire multimodule with sub-addresses completing the
remaining addresses. For compatibility with existing installations using Notifier CLIP Protocol, the first address
is set from 01 to 90; the other modules are automatically assigned the next nine addresses; up to six unused
addresses can be disabled by dip switch.
Specifications
Ten Channel Input Module
NFXI-MM10
Mechanical Specification
Electrical Specification
• Dimensions:
Height:
Width:
Depth: 25 mm
173 mm
147 mm
• Weight 0.5 kg (package included)
• Wire Gauge for Terminals
Maximum Minimum 3.25 mm2 (12 AWG)
0.8 mm2 (18 AWG)
• Maximum Standby Current 3500 uA
• Maximum Alarm Current (red LED) 5 mA
• Maximum Supervising Line
Wiring Resistance 40 ohm
• Operating Voltage Range 15-32 VDC
• Maximum Wiring Resistance 40 ohm
Environmental Specifications
Features
• Uses Opal protocol (up to 159 addresses)
• Operating Temperature -10°C to +55°C
• Operating Humidity Range:
10% to 93% RH
• Individual Tri-colors LED indicators
• Controllable Isolation
• Unused addresses may be disabled
Connection Detail
• Rotary address switches
• Class B operation
• Removable plug–in terminal blocks
• Complies with EN54-17 and EN54-18
Mounting Detail
The multiple input and output modules are PCB Boards and need to be
mounted in suitable metal enclosures.
M200–SMB–MM Surface mounting metal box. Dimensions H 280 x W 229 x D 64mm
Page 10 of 14 - 990-153_0713
www.notifierfiresystems.co.uk
10 Way Output Module CMX-10RM
Each output is individually addressed and controlled by the control equipment. This provides a cost effective,
compact solution for installations requiring multiple switching and / or monitoring at a single location.
Each output consists of a form C (change over) relay contact providing both normally open and normally closed
contacts rated 2A at 30Vdc.
Each module card utilises up to 10 consecutive addresses with the base address being set by DIP switch
although any of the 10 addresses may be individually disabled allowing the use of this address by other modules
on that loop.
Specifications
10 Way Output Module CMX-10RM
Mechanical Specification
• Dimensions:
Height:
Width:
Depth: Electrical Specification
233 mm
70 mm
13 mm
The modules are supplied as a P.C.B. allowing installation in to other
equipment housings such as control cabinets. 5 x 3.5mm mounting
holes provide suitable secure mounting for the P.C.B’s. Each module
occupies a single Notifier Loop Module address with the first address
being set by DIP switch SW2 and subsequent address being base
address + n up to a maximium of 10. Individual modules may be
disabled via a second DIP switch SW1 such that any module address in
the range can be used for other module addresses on the loop.
• Current Consumption
1.7mA with communication and LED blink enabled
• LED Current, 5mA @ 24Vdc (LED on) per module
Environmental Specifications
• Operating temperature -10°C to +55°C
• Relative humidity:
10% to 93%, non-condensing
Connection Detail
Mounting Detail
Mount using multi-mount enclosure 002-439
Page 11 of 14 - 990-153_0713
www.notifierfiresystems.co.uk
10 Way Input Module MMX-10M
Each input is individually addressed and controlled by the control equipment. This provides a cost effective,
compact solution for installations requiring multiple switching and / or monitoring at a single location.
Inputs may be configured to monitor for open circuit, short circuit and active (fire) conditions.
Each module card utilises up to 10 consecutive addresses with the base address being set by DIP switch
although any of the 10 addresses may be individually disabled allowing the use of this address by other modules
on that loop.
Specifications
10 Way Input Module MMX-10M
Mechanical Specification
• Dimensions:
Height:
Width:
Depth: Electrical Specification
233 mm
70 mm
13 mm
• Current Consumption
1.7mA with communication and LED blink enabled
• LED Current, 5mA @ 24Vdc (LED on) per module
Environmental Specifications
The modules are supplied as a P.C.B. allowing installation in to other
equipment housings such as control cabinets. 5 x 3.5mm mounting
holes provide suitable secure mounting for the P.C.B’s. Each module
occupies a single Notifier Loop Module address with the first address
being set by DIP switch SW2 and subsequent address being base
address + n up to a maximium of 10. Individual modules may be
disabled via a second DIP switch SW1 such that any module address in
the range can be used for other module addresses on the loop.
• Operating temperature -10°C to +55°C
• Relative humidity:
10% to 93%, non-condensing
Connection Detail
Mounting Detail
Mount using multi-mount enclosure 002-439
Page 12 of 14 - 990-153_0713
www.notifierfiresystems.co.uk
5 Way Input and 5 Way Output Module MCX-55
Each input and output are individually addressed and controlled by the control equipment and provide a cost
effective, compact solution for installations requiring multiple switching and / or monitoring at a single location.
Inputs may be configured to monitor for open circuit, short circuit and active (fire) conditions. Each output
consists of a form C (change over) relay contact providing both normally open and normally closed contacts
rated 2A at 30Vdc.
Each module card utilises up to 10 consecutive addresses with the base address being set by DIP switch
although any of the 10 addresses may be individually disabled allowing the use of this address by other modules
on that loop.
Specifications
MCX-55 5 Way Input and 5 Way Output Module
Mechanical Specification
• Dimensions:
Height:
Width:
Depth: Electrical Specification
233 mm
70 mm
13 mm
The modules are supplied as a P.C.B. allowing installation in to other
equipment housings such as control cabinets. 5 x 3.5mm mounting
holes provide suitable secure mounting for the P.C.B’s as indicated
overleaf. Each module occupies a single Notifier Loop Module address
with the first address being set by DIP switch SW2 and subsequent
address being base address + n up to a maximium of 10. Individual
modules may be disabled via a second DIP switch SW1 such that any
module address in the range can be used for other module addresses
on the loop.
• Current Consumption
1.7mA with communication and LED blink enabled
• LED Current, 5mA @ 24Vdc (LED on) per module
Environmental Specifications
• Operating temperature -10°C to +55°C
• Relative humidity:
10% to 93%, non-condensing
Connection Detail
Mounting Detail
Mount using multi-mount enclosure 002-439
Page 13 of 14 - 990-153_0713
www.notifierfiresystems.co.uk
Product Range at a Glance
Part Number
Single output module
M701
Single input unit
M710
Dual input unit
M720
Dual input, single output module
M721
Single 230Vac output unit inc. surface mount box
M701-240
Single 230Vac output unit inc. DIN rail mounting enclosure
M701-240-DIN
Surface Mount Box
M200E-SMB
Surface Mount Box for 6 M7xx series modules
SMB6-V0
Panel Mount Bracket
M200E-PMB
DIN rail mounting clip
M200E-DIN
Addressable micro monitor (input) module - Opal compatible without isolator
NFX-MM1M
Six Channel Output Module - Opal protocol changeover relay output with built-in loop isolation. Complete with
rotary address switch and plug-in terminal blocks. Requires M200-SMB-MM for mounting
NFXI-RM6
Ten Channel Input Module - Opal protocol input module with built-in loop isolation. Complete with rotary address switch and plug-in terminal blocks. Requires M200-SMB-MM for mounting
NFXI-MM10
Surface mounting metal box. H 280 x W 229 x D 64mm
Suitable for mouning one module. (NFXI-RM6, NFXI-MM10)
M200-SMB-MM
10 Way Relay Output Module
CMX-10RM
10 Way Input Module
MMX-10M
5 Way Input & 5 Way Relay Output Module
MCX-55
Multi-Mount Enclosure. Metal, NOTIFIER Black/Grey. The enclosure is capable of housing: one CMX-10RM or
MMX- 10M or MCX-55 module, or up to two MRM or ZMX modules or one NION-232B.
002-439
Page 14 of 14 - 990-153_0713
Charles Avenue
Burgess Hill
W. Sussex
RH15 9UF
T: +44 (0) 116 246 2255
F: +44 (0) 116 246 2210
E: sales@notifierfiresystems.co.uk
www.notifierfiresystems.co.uk