Owner's Manual
Covering Amana Cooktop ACC3660
Contents
Gas Downdraft
Cooktop
Keep instructions for future reference.
Be sure manual stays with cooktop.
Important Safety Information ................ 3
Cooktop Cartridges ............................. 5
Adjusting Surface Burner Flame ......... 8
Cookware Recommendations .............. 9
Using the Cooktop ............................ 10
Care and Cleaning ............................. 12
Troubleshooting ................................. 13
Amana Warranty ............................... 16
Natural Gas ONLY
This cooktop is not designed for use with LP/Propane gas
36-32057201-0
Thank you for buying an Amana Cooktop!
Please take the time to complete the registration card and return promptly.
If registration card is missing, call Amana Consumer Affairs Department.
When contacting Amana, provide product information from serial plate
located in the cartridge well.
Model Number __________________________________
Manufacturing (P) Number _________________________
Serial Number (S/N) ______________________________
Purchase Date __________________________________
Dealer Name ___________________________________
Dealer Address _________________________________
Dealer Phone ___________________________________
Keep this manual and your sales receipt together in a safe place for
future reference or if warranty service is required.
For answers to questions or to locate an authorized servicer, call
1-800-843-0304 inside USA or 319-622-5511 outside USA. Warranty
service must be performed by an authorized servicer. Amana Appliances
also recommends contacting an authorized servicer if service is required after
warranty expires.
Questions on cooking, cleaning or usage?
Refer to
Product Assistance at www.amana.com
or
call Consumer Affairs at 1-800-843-0304
What You Need to Know
about Safety Instructions
Warning and Important Safety
Instructions appearing in this manual
are not meant to cover all possible
conditions and situations that may
occur. Common sense, caution, and
care must be exercised when installing,
maintaining, or operating cooktop.
Always contact your dealer, distributor,
service agent, or manufacturer about
problems or conditions you do not
understand.
Asure™ Extended
Service Plan
Amana Appliances offers long-term
service protection for this new
cooktop. Asure™ Extended Service
Plan, covering functional parts, labor,
and travel charges, is specially
designed to supplement a strong
warranty. Call 1-800-528-2682 for
information.
Parts and Accessories
Purchase replacement parts and
additional accessories by phone.
To order accessories for your Amana
product, call
1-800-843-0304 inside USA or
319-622-5511 outside USA.
Save Time and Money
If something seems unusual, please
check Troubleshooting section, which
is designed to help you solve problems
before calling service.
If you have a question, call us at
(800) 843-0304 or write us at:
Consumer Affairs Department
Amana Appliances
2800 - 220th Trail
Amana, Iowa 52204
Remember to include model number
of your appliance, serial number, date
of purchase and your daytime phone
number.
Recognize Safety Symbols, Words, Labels
! DANGER
DANGER—Immediate hazards which WILL result in severe personal
injury or death.
! WARNING
WARNING—Hazards or unsafe practices which COULD result in severe
personal injury or death.
! CAUTION
CAUTION—Hazards or unsafe practices which COULD result in minor
personal injury or product or property damage.
2
IMPORTANT SAFETY INFORMATION
California Safe Drinking Water
and Toxic Enforcement Act (Proposition 65)
The Governor of California is required to publish a list of substances known
to the state of California to cause cancer or reproductive harm and requires
businesses to warn customers of potential exposures to such substances.
This appliance may contain or produce a chemical or chemicals which can
cause death or serious illness and which are known to the State of
California to cause cancer, birth defects, or other reproductive harm. To
reduce the risk from substances in the fuel or from fuel combustion, make
sure this appliance is installed, operated and maintained according to the
instructions provided.
! CAUTION
Do not store items of interest to children in cabinets above a
cooktop or on the backguard behind the cooktop—children climbing
on the cooktop to reach items could be seriously injured.
! CAUTION
To avoid risk of delayed or
improper ignition, do not obstruct
the flow of combustion or
ventilation air.
! WARNING
To avoid risk of electrical shock,
personal injury or death, verify
your cooktop has been properly
grounded and always disconnect
it from main power supply before
servicing.
! WARNING
! CAUTION
DO NOT TOUCH SURFACE BURNERS OR AREAS NEAR
BURNERS—Areas near surface burners may become hot enough to
cause burns. During and after use do not touch, let clothing or other
flammable materials touch or contact surface burners or areas near
surface burners until they have had enough time to cool. These areas
include the cooktop and backguard.
If the information in this manual is
not followed exactly, a fire or
explosion may result causing
property damage, personal injury
or death.
— Do not store or use gasoline
or other flammable vapors and
liquids in the vicinity of this or
any other appliance.
— What To Do If You
Smell Gas
! CAUTION
To avoid fire or smoke damage,
• remove any flammable materials from area around cooktop. Items
like plastic containers and paper manuals can melt or burn.
• clean excess spills as soon as possible.
In Case of Fire
Fires can occur as a result of over cooking or excessive grease.
Though a fire is unlikely, if one occurs, proceed as follows:
Surface Burner Fire
1. Smother the fire with a nonflammable lid or baking soda, or use a Class
ABC or BC extinguisher.
Not water. Not salt. Not flour.
2. As soon as it is safe to do so, turn the surface controls to OFF. Turn off
power at main circuit breaker or fuse box. Turn off gas supply.
• Do not try to light any
appliance.
• Do not touch any electrical
switch.
• Do not use any phone in your
building.
• Immediately call your gas
supplier from a neighbor’s
phone. Follow the gas
supplier’s instructions.
• If you cannot reach your gas
supplier, call the fire
department.
— Installation and service must
be performed by a qualified
installer, service agency or the
gas supplier.
SAVE THESE INSTRUCTIONS
3
IMPORTANT SAFETY INFORMATION (cont’d)
ALL APPLIANCES
SURFACE BURNERS
1. Proper Installation—Be sure your appliance is
properly installed and grounded by a qualified
technician.
2. Never Use Your Appliance for Warming or Heating
the Room.
3. Do Not Leave Children Alone—Children should not
be alone or unattended in the area where the
appliance is in use. They should never be allowed
to sit or stand on any part of the appliance.
4. Wear Proper Apparel—Loose fitting or hanging
garments should never be worn while using
appliance.
5. User Servicing—Do not repair or replace any part
of the appliance unless specifically recommended
in the manual. All other servicing should be referred
to a qualified technician.
6. Storage in or on Appliance—Flammable materials
should not be stored near surface units.
7. Do Not Use Water On Grease Fires—Smother fire
or flame, or use dry chemical or foam-type
extinguisher.
8. Use Only Dry Potholders—Moist or damp
potholders on hot surfaces may result in burns from
steam. Do not let potholder touch burners. Do not
use a towel or other bulky cloth.
!
•
•
•
•
•
•
•
1. Use Proper Pan Size—This appliance is equipped
with one or more surface burners of different sizes.
Select utensils having flat bottoms large enough to
cover the surface burner. The use of undersized
utensils will expose a portion of the burner to direct
contact and may result in ignition of clothing. Use
of oversized utensils concentrates heat on cooking
surface and can cause damage to cooktop. Proper
relationship of utensil to burner improves efficiency.
2. Never Leave Surface Burners Unattended—Boilover
causes smoking and greasy spillovers that may
ignite.
3. Make Sure Reflector Pans or Drip Bowls Are in
Place—Absence of these pans or bowls during
cooking may subject wiring or components
underneath to damage.
4. Protective Liners—Do not use aluminum foil to line
surface burner drip bowls or oven bottom, except as
suggested in the manual. Improper installation of these
liners may result in a risk of electric shock, or fire.
5. Glazed Cooking Utensils—Only certain types of
glass, ceramic, earthware, or other glazed utensils
are suitable for cooktop service without breaking due
to sudden change in temperature.
6. Utensil Handles Should Be Turned Inward and Not
Extended Over Adjacent Surface Burners—To
reduce the risk of burns, ignition of flammable
materials, and spillage due to unintentional contact
with the utensil, the handle of a utensil should be
positioned so that it is turned inward, and does not
extend over adjacent surface burners.
Precautions
•
Do not cook food directly on
cooktop surface, always use
cookware.
Do not mix household cleaning products. Chemical
mixtures may interact with objectionable or even
hazardous results.
Do not put plastic items on warm cooking areas.
They may melt and stick.
Do not slide rough metal objects across cooktop
surface. Scratching or metal marking can result.
Do not leave fat heating unless you remain nearby.
Fat can ignite if overheated by spilling onto hot
surfaces.
Do not allow pots to boil dry as this can cause
damage to cooking surface and pan.
Do not use cooktop surface as a cutting board.
Do not use cooktop for storage or as a display
counter.
VENTILATION HOODS
1. Clean Ventilating Hoods Frequently—Grease should
not be allowed to accumulate on hood or filter.
2. When flaming foods under the hood, turn the fan on.
DELAYED IGNITION
Surface burners
Burner should ignite within 4 seconds. If burner does not
ignite within 4 seconds, turn control knob to OFF and
follow directions for installing burner caps in Adjusting
Surface Burners. Try again. If burner still does not ignite
within 4 seconds, contact an authorized servicer.
SAVE THESE INSTRUCTIONS
4
Cooktop Cartridges
! WARNING
To avoid personal injury, do not
touch surface burners or area near
burners.
• Surface burners may be dark in
color even when hot.
• Areas near burners may be hot
enough to burn.
• Do not allow clothing or other
flammable materials to touch
cooktop during or after use.
Which cartridge should you use?
Your cooktop comes with two gas burner cartridges, but by adding
accessories, you can customize your cooktop to suit your specific needs.
CARTRIDGE TYPE
BURNER TYPE
PLACEMENT
Burner (standard)
Two gas burners
Larger front burner, smaller
rear burner.
Grill (accessory)
Gas grill burner
Can be installed right side
only.
Griddle (accessory)
Gas grill burner
Installed on top of grill
accessory.
! WARNING
To avoid personal injury, all
controls must be in OFF position
before removing or installing
cartridges.
To install the gas burner cartridge:
1. Turn all controls to OFF.
2. Verify surface of cooktop is cool to the touch.
3. Hold cartridge with venturi pointing toward rear of cooktop.
• If cartridge pan from grill or griddle cartridge is in the well, remove before installing the cartridge.
4. Place end of cartridge into cooktop well with venturi facing rear of well.
• Lifting cartridge over 45° angle can cause damage to
cartridge terminals.
5. Slide cartridge towards rear of cooktop until cartridge
engages. Lower front of cartridge into well.
6. Place burner caps on burner
• The cap should not be loose.
• The pegs in the burner base should fit into the
recess on the underside of burner cap.
• Cap should be the correct size for each burner base.
• Cap must be clean and dry for proper ignition.
• Once cap is properly placed, place grate over cap and burner base .
To remove burner cartridges:
1. Turn all controls to OFF. Make sure surface is cool.
• Do not tilt cartridge too high.
• Lifting cartridge over 45° can cause damage to burner venturi.
2. Remove burner grate and cap.
3. Using tab on front of cartridge, lift up slightly.
4. Pull cartridge toward the front of cooktop and carefully lift out.
5
Cooktop Cartridges
(cont’d)
Installing the grill or griddle accessory
! WARNING
To avoid personal injury, do not
touch surface burners or area
near elements.
• Surface burners may be dark in
color even when hot.
• Areas near burners may be hot
enough to burn.
• Do not allow clothing or other
flammable materials to touch
cooktop during or after use.
! WARNING
To avoid personal injury, all
controls must be in OFF position
before removing or installing
cartridges.
1
Turn all controls
to OFF position
HI
Surface of cooktop must be
cool to the touch for burners to
be handled safely.
LO
OFF
Do not cook immediately
before installing cartridges or
changing cartridges.
2
Place drip pan
in cartridge
well in cooktop
Place drip pan in bottom of well. Grill can be installed in
RIGHT SIDE only.
Drip pan
6
Cooktop Cartridges
3
Place the grill
burner in cooktop
! CAUTION
To avoid risk of personal property
damage, do not place the griddle
accessory over the grill grate.
The griddle accessory is to be
placed directly over the grill
burner only.
Place end of cartridge into cooktop
well with air shutters facing rear of
well. Venturi should slide over
orifice hoods as far as possible.
4
Place grill or
griddle over the
grill burner
(cont’d)
Only the grill grate or the griddle
accessory can be used at one time.
The griddle can not be placed on top
of the grill grate.
Griddle accessory must be placed
so the grease trap is toward the rear
of the cooktop.
To remove the grill cartridge:
1.
2.
3.
4.
Turn all controls to OFF position.
Verify the cartridge and surface of grill/griddle is cool to the touch.
Remove grill grate or griddle accessory from cartridge.
Remove burner cartridge.
• Do not tilt cartridge too high. Lifting element over 45° can cause
damage to burner venturi.
5 . Remove drip pan.
• Clean drip pan before next use.
7
Grease
trap
Adjusting Surface Burner Flame
Adjustments must conform to all local, municipal and state building
codes, and local utility regulations.
JUDWH
Placing burner caps
Burner cap must be correctly seated on the burner base for proper operation
of the burner. Verify cap is properly aligned and leveled by moving the
burner cap around on burner base while cooktop is cool.
EXUQHUFDS
•
•
EXUQHUEDVH
•
•
•
The cap should not be loose.
The pegs in the burner base should fit into the recess on the underside
of burner cap.
Cap should be the correct size for each burner base.
Cap must be clean and dry for proper ignition.
Once cap is properly positioned, place grate over cap and burner base.
Testing and adjusting surface burner flame
A properly adjusted surface burner on a high setting has flames that are
clean and blue with a distinct inner cone approximately 1/4 to 1/2" long.
%XUQHU
•
•
•
•
See Delayed Ignition section in Important Safety Information for safety
warnings and procedures.
Flames will not be a uniform size around the cap. This
distribution around the cap and grate allows for optimal heating.
If burner flame is blowing or noisy, airflow should be reduced to
the burner (close air shutter).
If burner flame is weak and does not hold its shape, airflow should be
increased to the burner (open air shutter).
Adjusting Surface Burner Flame
1/2"
Close
Open
1.
2.
3.
4.
5.
Turn controls to OFF position.
Remove grate and burner caps from cartridge.
Remove cartridge according to Cooktop Cartridges.
Locate air shutters on rear of cartridge.
Adjust each air shutter using small screw driver.
• Slide air shutter until shutter is approximately 1/8 inch open.
6. Replace cartridge according to Cooktop Cartridges and check for proper
flame.
7. Replace burner grate when flame is properly adjusted.
Adjusting Grill Cartridge Burner Flame
1.
2.
3.
4.
Turn controls to OFF position.
Remove grill or griddle from cartridge if necessary.
Remove cartridge according to Cooktop Cartridges.
Locate air shutters on rear of cartridge, loosen air shutter lock screw,
and open or close air shutter.
• Tighten air shutter lock screw after adjusting.
5. Replace cartridge according to Cooktop Cartridges and check for proper
flame.
8
Cookware Recommendations
What Should You Consider in Cookware?
Flat Pan Test
SELECT
AVOID
Flat bottomed cookware.
Cookware with rounded or warped bottoms.
Heavy gauge metal cookware.
Light gauge metal cookware.
Handles that are secure, that are not
heavy enough to tilt pan.
Cookware with loose or broken handles or
heavy handles that tip pan when empty.
Proper pan size.
Cookware that is smaller than or greater than
burner grate by 1 inch.
Flat bottomed wok
Wok with a ringstand on bottom.
For best cooking results, use a pan
with a flat bottom. To determine if
pan has a flat bottom:
1. Rotate a ruler along bottom
of pan. If pan is not flat, gaps
between bottom of pan and
edge of ruler can be seen.
2. A small groove or mark on a
pan does not affect cooking
times. However, if a pan has
a gap, formed rings, or an
uneven bottom, it does not
cook efficiently and in some
cases may not boil liquid.
Does not cover burner
More than 1-inch
overhang
COOKWARE
MATERIAL
Can I can?
USES
Aluminum
Heats and cools quickly. Use for frying, braising,
and roasting.
Stainless Steel
Heats and cools at moderate rate. Use for soups,
sauces, vegetables, general cooking.
Copper Clad /
Tin Lined
Heats and cools quickly. Use for gourmet cooking,
wine sauces, egg dishes.
Cast Iron
Heats and cools slowly. Use for low heat cooking,
frying.
Enamelware
Ceramic (Glass)
Heating speed depends on base metal in the
cookware. Use for low heat cooking.
Heats and cools slowly. Use for low heat cooking.
9
Canning is not recommended with
any of the Amana gas ranges or
cooktops due to the intense heat and
large cookware required to can.
The high, sustained heat generated by
the canning cookware overheats both
the burners and the surface of the range
or cooktop. This may cause damage to
burners, knobs, or finish, and may even
cause overheating of surrounding walls.
Damage incurred by canning, or
attempting to can, is not covered under
warranty.
Using the Cooktop
! WARNING
To avoid risk of serious personal
injury, property damage, or fire,
do not leave surface burners
unattended while in operation.
Grease and spillovers can ignite
causing a fire.
Delayed Ignition
Burner should ignite within 4 seconds.
If burner does not ignite within 4
seconds turn control knob to OFF
position and follow directions in
Adjusting Surface Burner Flame
section. Try burner again. If burner still
does not ignite in 4 seconds, contact an
authorized servicer.
Setting Surface Burner Controls
Burner should ignite within 4 seconds. If burner does not ignite within
4 seconds, turn control knob to OFF position and follow directions in
Adjusting Surface Burner Flame section.
1. Push in and turn control knob to LITE.
• Burner should ignite within 4 seconds.
• Burner sparks until knob is turned from LITE.
2. After gas ignites, turn control knob to desired
setting.
• Knobs do not have distinct ‘clicks’.
• Use HI to bring food to boiling temperatures.
When food is boiling temperature setting
should be reduced.
• After lighting burner do not operate for long
periods of time without cookware on grate. The
finish on the grate can chip without cookware to absorb the heat.
• Flame size should match the size of the pan. Do not allow the flame
to extend up the sides of the pan. This can cause clothing to ignite,
make the handle hot, or cause burns.
3. When finished cooking, turn control knob to OFF position.
SURFACE ELEMENT
CONTROL SETTINGS
! WARNING
To avoid risk of personal injury
or property damage due to
excessive smoke or fire do not
attempt to use grill or griddle
when power is not available.
Fan must be running to exhaust
smoke and fumes.
WHEN TO USE SETTING
Use to prepare food at less than boiling
temperatures or to simmer.
Use to maintain boiling of larger amounts of food,
low temperature frying.
Use to bring food to boiling temperatures. When
food is boiling temperature setting should be
reduced to LO through MED.
LO
MED
HI
During a Power Outage
Although the system that lights the
burners is electric, surface burners can
be ignited during a power outage.
Never attempt to light grill burner
(for grill or griddle use) during a
power failure.
1.
2.
3.
Proper Burner Flame Size
•
•
•
While turning burner control knob, watch the burner flame.
Flame size should match the size of the pan.
Flames that extend up the sides of the pan can ignite clothing, making
the handle hot, or cause burns.
Hold match at base of desired
surface burner.
Push in burner control knob and
turn to LITE position.
After gas ignites, remove match
from burner and turn burner control
knob to desired setting.
10
Using the Cooktop (cont'd)
Using the Smoke Control Grill
or Griddle
Before using the grill grate or griddle accessory for the first time, wash it
with warm soapy water, rinse, and dry thoroughly. Lightly wipe the top of the
grill or griddle surface with cooking oil to prevent food from sticking (do not use
shortening or butter). Do not use metal cooking utensils on either the grill or
griddle.
1. While cooktop is cool, insert grill burner in cooktop well.
2. Place grill grate OR griddle accessory over the burner.
2. Push in right front and right rear and control knobs and turn.
• Burner sparks until burner control knob is turned from LITE.
• If using the grill, allow it to preheat for approximately 10 minutes at
MED HI.
• Fan turns on at low speed.
• If the rear knob is used, the indicator light glows but the grill will not
heat, and the fan will not operate.
• Grill or griddle should not be set at HI setting without food. It will
damage the non stick finish.
3. Place food on cooking surface.
• If food begins to cook too quickly, reduce heat.
• When using the griddle, do not allow grease to accumulate.
4. When finished cooking, turn control to OFF and allow cartridge to cool.
5. Once cool, clean the pan and the grill grate or griddle. Do not clean the
grill burner. Any residue left on the actual burner will burn off with future
use.
• Do not use abrasive cleaners that may harm the non stick finish.
• Grill grate and griddle may be washed in a dishwasher.
Exhaust Fan
HI
LO
OFF
•
•
•
•
The variable speed fan is built into the center of the cooktop. The
fan is located beneath the vent area and is used to remove cooking
vapors, odors and smoke.
The fan automatically turns on at low speed when using grill or griddle.
Fan must be manually turned to high speed.
Fan cannot be turned off while grill or griddle are operating.
Clean fan vents and filters frequently. Grease should not be allowed to
accumulate on vent or filter.
11
! WARNING
To avoid risk of serious personal
injury, property damage, or fire,
do not leave surface burners
unattended while in operation.
Grease and spillovers can ignite
causing a fire.
! WARNING
To avoid risk of smoke damage
or fire, do not operate cooktop
without filter.
Removing Vent Filter
1. Lift filter cover to remove vent
filter.
• Duct filter lifts out of vent.
2. Clean and reinstall filter and
vent cover.
• Clean in the dishwasher or
with damp cloth and warm
soapy water.
Care and Cleaning
3DUW
Burner caps and
grates
Hard to clean
burner caps and
grates
6XJJHVWHG0DWHULDOV
*HQHUDO'LUHFWLRQV$QG5HFRPPHQGDWLRQV
Soap and warm water
Cool before cleaning. Frequent cleaning with soap and water, and non-abrasive
pad prolongs time between deep cleanings. Be sure to dry thoroughly.
½ Cup Ammonia
Place burner caps and grates in plastic bag with ½ cup ammonia. Do not pour
ammonia into bag. Ammonia must remain in cup. To avoid rust, do not soak
grates in ammonia. Close bag tightly and leave grate and caps overnight. Before
bag is opened turn face away to avoid breathing or eye contact with fumes.
Remove burner caps and grates from bag and rinse. Clean according to
instructions above.
Gas burners
None
Burners do not need to be cleaned. Soil will burn off while cooking
Cooktop trim
Soap and warm water
Control knobs
Mild soap and warm water
Fan cover and
filter
Soap and warm water, or
dishwasher
Fan must be off before removing filter cover. Clean filter and cover with damp
cloth and soapy water. To remove grease and dried on soil, soak before
cleaning. Rinse and dry after cleaning. Filter and filter cover can be cleaned in
dishwasher. Always replace filter and cover before operating cooktop.
Grill grate or
griddle accessory
Dishwasher or
Soap and a non abrasive
scrubbing pad
Clean in the dishwasher or with damp cloth and soapy water. If necessary, clean
with nonabrasive cleaners or pads. Rinse and dry.
Drip pan,
cartridge pan, or
drip bowls
Soap and warm water
Allow cooktop to cool before cleaning. Clean with damp cloth and soapy water.
Rinse and dry thoroughly. For extra dried on soil, soak the drip bowls in warm
soapy water.
Clean cooktop trim with damp cloth and soapy water. If necessary, clean with
nonabrasive cleaners or pads. Dry thoroughly when finished to avoid rusting.
Do not use harsh powders, oven cleaners, scouring pads, or steel wool.
Pull off knobs. Wash gently but do not soak. Dry and return controls to cooktop,
making sure to match flat area on the knob to the flat area on shaft.
Remove panel and gasket:
Glass control
panel and gasket
Soap and warm water
1.
2.
3.
4.
Pull knobs off stems to remove.
Lift glass out of control panel.
Lift gasket out of control panel.
Replace gasket and knobs after cleaning.
Caring for Stainless Steel
Amana’s stainless steel appliances have been factory finished for high shine and
luster. To maintain this quality appearance:
DO USE:
• Warm soapy water for routine
cleaning on a cool cooktop.
• Dry with soft, clean cloth.
• For heavy soil, ONLY a
stainless steel cleaner designed
for kitchen appliance use.
Citric Acid
DO NOT USE:
•
•
•
•
•
•
•
Abrasive powders or liquids
Citrus based cleaners
Ammonia
Steel wool pads
Abrasive cloths
Oven cleansers
Acidic or vinegar based
12
To prevent damage to the
finish of your stainless
steel cooktop, do not allow
mustard, tomato juice, marinara
sauce, or other citrus based sauces
or products to remain on stainless
steel surface. Citric acid permanently
discolors stainless steel.
Troubleshooting
You may save time and money by checking items below before calling for service. List includes common concerns
that are not the result of defective workmanship or materials. If your question is not explained below, contact
Amana Consumer Affairs Department at 800-843-0304 or visit our website at www.amana.com
7RSLF
3RVVLEOH&DXVH
6ROXWLRQ
OPERATION
Appliance not working
Make sure appliance is plugged in.
Verify that circuit breaker is not tripped.
Replace fuse but do not change fuse capacity.
Power outage
Control knobs do not turn
Normal
Push knob in and then turn.
Improper Installation
Surface burners do not light
Turn knob to OFF. Remove cartridge and install
according to instructions in Cooktop Cartridges section.
NOISE
Roaring or loud flame sound
Improper air shutter setting
Cracking or popping sound
Normal
Wet cooking utensils or possible spillage.
Dirt
Use recommended cleaner to remove dirt
Adjust air shutter.
APPEARANCE
Discoloration
Water spots/marks
Make sure surface is cool. Put a small amount of white
vinegar on the spot and let sit for a few minutes. Rub with
nonabrasive nylon pad. Wipe off any excess with damp
paper towel.
Questions on cooking, cleaning or usage?
Refer to
Product Assistance at www.amana.com
or
call Consumer Affairs at 1-800-843-0304
13
14
15
Amana Warranty
Full ONE Year Warranty
Amana Appliances will repair or replace, including related labor and travel, any part (f.o.b. Amana Iowa) which
proves defective as to workmanship or materials.
Limited Warranty
After one year from the date of original retail purchase, Amana will provide a free part, as listed below, to
replace any part that fails due to a defect in materials or workmanship. The owner will be responsible for
paying all other costs including labor, mileage, and transportation.
Second through Fifth Year
Amana will replace glass/ceramic cooktop, electric surface elements or gas surface burners, part only
(f.o.b. Amana Iowa) which proves defective as to workmanship or materials.
What is not covered by these
warranties
•
•
•
•
•
•
•
•
To Receive Warranty Service
Service must be performed by an authorized Amana
service representative. To schedule service, contact
the Amana dealer where you purchased your appliance
or contact Amana Appliances Factory Service.
Replacement of household fuses, resetting of
circuit breakers, or correction to household wiring
or plumbing.
Normal product maintenance and cleaning,
including light bulbs.
Products with original serial numbers removed,
altered, or not readily determined.
Products purchased for commercial, industrial,
rental, or leased use.
Products located outside of the United States
or Canada.
Premium service charges, if the servicer is
requested to perform service in addition to normal
service or outside normal service hours or area.
Adjustments after the first year.
Repairs resulting from the following:
• Improper installation, exhaust system, or
maintenance.
• Any modification, alteration, or adjustment not
authorized by Amana.
• Accident, misuse, abuse, fire, flood, or
acts of nature.
• Connections to improper electrical current,
voltage supply, or gas supply.
• Use of improper pans, containers, or
accessories that cause damage to the product.
Amana Appliances Factory Service
1-800-628-5782 inside USA
When contacting Amana Appliances please
include the following information:
•
•
•
•
•
Your name, address, and daytime telephone
number.
Model number and serial number of your appliance
(located on the underside of the cooktop).
The name and address of your dealer and the date
of purchase.
A clear description of the problem.
Proof of purchase (sales receipt).
For more information,
Amana Appliances Consumer Affairs
Amana Appliances
2800 220th Trail
Amana, Iowa 52204
1-800-843-0304 inside USA
(319) 622-5511 worldwide
IN NO EVENT SHALL AMANA BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
This warranty gives you specific legal rights, and you may have others which vary from state to state. For example, some states
do not allow the exclusion or limitation of incidental or consequential damages, so this exclusion may not apply to you.
Amana Appliances Online • http://www.amana.com
Part No.36-32057201-0
Printed in U.S.A. 07/01
16
Ó 2001 Amana Appliances
Amana, Iowa 52204
Download PDF
Similar pages
LG LCG3011ST User's Manual
Mora VDP 325 W
Mora VDP 642 GX
Mora VDP 642 GX1