null  null
TM
Dual Alarm Clock Radio
with CD Player
OWNER'S MANUAL
CKD9918
Visit our web site at www.emersonradio.com
WARNING
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE
OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE. TO
PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Avertissement: pour réduire le risque d‚incendie ou de choc électrique, ne pas exposer cet appareil
sous la pluie et l‚humidité.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to
alert the user to the presence of
uninsulated dangerous voltage
within the products enclosure that
may be of sufficient magnitude to
constitute a risk of electric shock
to persons.
WARNING: TO REDUCE THE
RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER
(OR BACK), NO USER
SERVICEABLE
PARTS
INSIDE REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL.
The exclamation point within
an equilateral triangle is
intended to alert the user to
the presence of important
operating and maintenance
(servicing) instructions in the
literature accompanying the
appliance.
The Caution Marking may be located at the bottom enclosure of the apparatus.
Les précautions d’emploi sont inscrites en bas de l’appareil.
IMPORTANT SAFETY INSTRUCTIONS
1.) Read these instructions. Keep these instructions. Follow all instructions. Heed all warnings.
2.) Do not use this apparatus near water.
3.) Clean only with dry cloth.
4.) Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.
5.) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
6.) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has
two blades with one wider than the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong is provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
7.) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
8.) Only use attachments / accessories specified by the manufacturer.
9.) Unplug this apparatus during lightning storms or when unused for long periods of time.
10.) Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
11.) This appliance shall not be exposed to dripping or splashing water and no object filled with
liquids such as vases shall be placed on the apparatus.
L’appqreil ne doit pas être exposé aux écoulements ou éclaboussures et aucun objet ne
contenant de liquide,tel qu’un vase, ne doit être placé sur l’objet.
12.) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
1
13.) Do not overload wall outlet. Use only power source as indicated.
14.) Use replacement parts as specified by the manufacturer.
15.) The product may be mounted to a wall only if recommended by the manufacturer.
16.) Upon completion of any service or repairs to this product, ask the service technician to
perform Safety
17.)
This is CLASS II apparatus with double insulation, and no protective earth provided.
18.) To be completely disconnect the power input, the mains plug of apparatus shall be
disconnected from the mains. The mains plug of apparatus should not be obstructed OR should
be easily accessed during intended use.
Pour être complètement déconnecté de l'alimentation d'entrée, la prise doit être débranchée du
secteur. La prise du secteur ne doit pas être obstruée ou doit être facilement accessible pendant
son utilisation.
19.) Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
Les piles ne doivent pas être exposées à de forte chaleur, tel qu'à la lumière du soleil, au feu ou
autres choses de semblable.
20.) The marking information is located at the bottom of apparatus.
Les marquages sont inscrits en bas de l'appareil.
21.) Lithium battery replacement warning:
CAUTION:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent
type.
Précaution:
Danger d'explosion si les piles sont remplacées de façon incorrect. Remplacer les piles
seulement par le même type de pile ou l'équivalent.
Before We Begin
Thank you for purchasing this Emerson audio product. The Emerson brand is your
assurance of quality, performance and value.
Our engineers have included many useful and convenient features in this product.
Please be sure to read this Owner's Manual completely to make sure you are getting
the maximum benefit from each feature.
This product was manufactured using the highest quality components and standards of
workmanship. It was tested by Emerson inspectors and found to be in perfect working
order before it left our factory. However, there is always the chance that some
problem may occur because of rough handling during shipment to the retail store or to
the final consumer.
If, after reading this Manual, you experience any problems with the operation of this
product, please refer to the instructions for obtaining service at the end of this Manual.
Emerson and Emerson retailers are committed to your satisfaction.
2
IMPORTANT NOTES
CLASS 1 LASER PRODUCT
This product contains a low power Laser Device.
• Avoid installing this unit in places
• Operate controls and switches as
exposed to direct sunlight or close to described in the manual.
heat radiating appliances such as • Before turning on the power, make
electric heaters, on top of other stereo certain that the power cord is properly
equipment that radiates too much heat, installed.
places lacking ventilation or dusty • When moving the set, be sure to first
areas, places subject to constant disconnect the power cord and remove
cords connected to other equipment.
vibration and/or humid or moist areas.
FCC Information
This equipment has been tested and found to comply with the limits for a class
B digital Device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
3
MPORTANT NOTES
PREPARATION
FOR USE
Unpacking And Set Up
Remove the unit from the carton, and remove all packing materials from the
unit.
Save the carton and packing materials in case the unit ever needs to be
returned for service. Using the original carton and packing materials is the
only way to safely repack the unit for shipment.
Remove any descriptive labels or stickers from the top or front of the unit. Do
not remove any labels from the back or bottom of the cabinet.
Remove any small strips of tape that may have been used to prevent the CD
from opening in transit.
Press the CD door in the area marked OPEN/CLOSE button to open the CD
door and remove the ‘dummy CD’ protection card from the CD player and
discard it. Close the CD door.
Unwind the AC power cord and extend it to its full length.
Place the unit on a stable, level surface such as a table, desk, shelf, etc.,
within easy reach of an AC outlet, out of direct sunlight, and away from
sources of excessive heat, dust, moisture or humidity.
Protect Your Furniture
This model is equipped with non-skid rubber 'feet' to prevent the product from
moving when you operate the controls. These 'feet' are made from
non-migrating rubber material specially formulated to avoid leaving any marks
or stains on your furniture. However certain types of oil based furniture
polishes, wood preservatives, or cleaning sprays may cause the rubber 'feet' to
soften, and leave marks or a rubber residue on the furniture. To prevent any
damage to your furniture we strongly recommend that you purchase small
self-adhesive felt pads, available at hardware stores and home improvement
centers everywhere, and apply these pads to the bottom of the rubber 'feet'
before you place the product on fine wooden furniture.
4
5
Battery Back Up System
This unit uses a single CR2032 battery (not included) to maintain the Time,
Alarm time and Radio preset stations settings in the event that it is accidentally
unplugged, or you experience a temporary power failure. We recommend that
you install a well-known brand of Lithium battery for longest life and best
performance.
Installing and replacing the backup battery
1.) Use screw driver to remove the screw that secures the battery compartment
at the bottom of the unit,and move out the battery cartridge from the battery
compartment
2.) Insert a new battery in the battery cartridge with " + " side facing up.
3.) Insert the battery cartridge back into the unit and secure it with the screw.
1
2
3
If the power is interrupted the clock display will go off but the battery will
maintain the Time, Alarm time and Radio preset stations settings. When power
is restored the time display will be correct and the alarm time and preset radio
stations will also be maintained.
If you notice that the time is wrong you probably experienced a power failure.
This could have been caused by a weak battery. Reset the clock and replace
the battery as soon as possible.
NOTE: The battery back up system will not work unless you have installed the
battery (CR2032, not included). Please see above for installation.
After you replaced the new battery, it will be necessary to re-enter the stations
in radio preset memories and reset the clock setting.
6
LOCATION OF CONTROLS AND INDICATORS
3
4
5
6
2
1
8
7
18 17 16 15
9
14
13
10
12
11
19
20
20
21
35
34
33
CLK. SET
22
FUNCTION
32
REPEAT/
RANDOM
PROG./
MEM.
PRESET +
23
31
24
25
26 27 28 29 30
7
LOCATION OF CONTROLS AND INDICATORS
1.)
2.)
3.)
4.)
5.)
6.)
7.)
8.)
9.)
10.)
11.)
12.)
13.)
14.)
15.)
16.)
17.)
18.)
19.)
20.)
21.)
22.)
23.)
24.)
25.)
26.)
27.)
28.)
29.)
30.)
31.)
32.)
33.)
34.)
35.)
VOLUME Control
DIMMER (HIGH / LOW) Selector Switch
STOP Button
PLAY / PAUSE Button
SNOOZE Button
LED Display
AUX IN Jack
PHONES Jack
AM TIME Indicator
AL1 (Alarm 1) Indicator
Time / Frequency Display
AL2 (Alarm 2) Indicator
ST (FM Stereo) Indicator
SLP (Sleep) Timer Indicator
PROG (Program) Indicator
RAN (Random) Indicator
REP (Repeat) Indicator
PLAY Indicator
AC Power Cord
Speaker
CLK (Clock) SET Button
FUNCTION Button (FM/AM/CD/AUX)
REPEAT/RANDOM Button
SLEEP Button
PROGRAM/MEMORY Button
PRESET + Button
TIME-DN /F.REV Button
TIME-UP /F.FWD Button
ALARM 1 Setting Button
ALARM 2 Setting Button
POWER “ON” LED Indicator
DISPLAY Button
POWER/ALARM OFF Button
CD Door OPEN/CLOSE
CD Compartment
8
Setting the Time
Press the POWER/ALARM OFF button to turn off
the unit, press once the CLK SET button and then
press either the
or
buttons to adjust the hour
time forward or backward as desired. Press again
or
the CLK SET button and then either the
buttons to adjust the minute time forward or
backward as desired.
AM
AM
Dimmer Control
If you find the display to be too bright for sleeping, slide the DIMMER selector
switch to the LOW position. The display DIMMER selector switch is located on
the left of the side cabinet.
Listening To the Radio
1.) Press the POWER/ALARM OFF button on the
top panel to turn the unit ‘On’. The POWER LED
indicator will light.
2.) Press the FUNCTION button repeatedly, it will
change on the function to FM radio, AM radio, CD
FM BAND
and Aux. To select FM Radio, press the
FUNCTION button repeatedly until the display
shows "r-F" (FM Radio), and then MHz will
appear on the display. To select AM radio, press
the FUNCTION button repeatedly until the
display shows "r-A" (AM radio), and then KHz will
AM BAND
now appear on the display.
3.) Press and hold the
or
buttons on the top panel to start stations
searches. When a station is received it will stop searching. Repeat the
procedure until your desired stations are selected.
If you tune to an FM stereo station, the ST (STEREO) indicator will light.
4.) Rotate the VOLUME control on the left side panel to adjust the volume level.
5.) When you are finished listening press the POWER/ALARM OFF button to
turn the unit ‘Off’. The POWER LED indicator turns off.
MHz
KHz
In Radio listening mode, the radio frequency display will appear for approx. 3
seconds, then the clock time will appear on the display. Press the DISPLAY
button to show the radio frequency, a few seconds later the display will show the
clock time.
AM
ST
MHz
9
To Store the Preset Stations
This radio system can program up to maximum 20 preset stations for each FM
radio and AM radio.
1. To store the stations to the preset station memory, press the
POWER/ALARM OFF button to turn On the unit.
2. Press FUNCTION button repeatedly until FM radio or AM radio is selected.
3. Press F.FWD or F.REV button to search your desired radio station.
4. Press PROG/MEM button once, the PROG
indicator and Preset station number “01” will
appear and blink on the display.
Press F.FWD or F.REV button to select a
desired location number (1—20) to store the
station. Press PROG/MEM button again to
confirm and store the station into memory.
Then the next preset station number appear
on the display.
5. Follow the procedure 2 to 4 to program the next station into the memory.
Listening to the Preset Stations
1. Press POWER/ALARM OFF button to turn On the unit.
2. Press FUNCTION button to select FM or AM radio.
3. Press PRESET+ button to select preset station. Each time pressing the
PRESET+ button, it will cyclically count up to display the preset station from
the memory.
Or you can press PRESET+ button once, and then press F.FWD or F.REV
button to select the preset stations location directly.
10
Antenna Information
AM
The AM ferrite bar antenna is inside the cabinet. If AM reception is
unsatisfactory, try turning the entire unit slightly until you find the direction that
provides the best reception for the desired station.
FM
The FM antenna is built in to the AC power cord. If the FM reception is weak,
try varying the position and direction of the power cord until you find the
strongest signal.
11
Playing Compact Discs
NOTE: This CD player can read CD-R/RW discs, in addition to normal CDs,
however; the compatibility of CD-R/RW discs may be affected by the type of
software that was used to create the discs, as well as the quality and condition
of the blank media you are using. 100% compatibility cannot be guaranteed.
This is not an indication of a problem with the player.
Normal Playback
1.) Press the POWER/ALARM OFF button to switch the unit ‘On’. The
POWER indicator will light.
2.) Press FUNCTION button repeatedly until the "cd" appears in the display.
3.) Press on the CD door in the area marked
OPEN to open the door.The display will
shows "OP" (open) for 5 seconds, then
change to show clock. If you have not already
done so, remove the ‘dummy CD’ transit
protection card from the CD player and
discard it.
4.) Place your disc on the center spindle with the printed label side facing up.
Press down near the center of the disc to make sure it is firmly ‘seated’ on
the spindle, press on the CD door in the area marked OPEN to close the
CD door.
5.) The “ – –” of “cd: – –” flashes while the player
reads the disc. The display will show the total
number of tracks for a few seconds and then
return to the correct time.
6.) Press the
button to begin playback. The
display will briefly show “cd: 01” (Track 1)
and playback on track 1 begins. After a few
seconds the display returns to the correct
time.
To see the track number at any time during
playback press the DISPLAY button. The track
number will appear for several seconds and
then the display returns to the correct time.
NOTE: If the disc is inserted incorrectly, or if
the disc is badly scratched and cannot be
read by the player, “d ISC” will appear on the
display for a few seconds, and then the
display returns to the correct time.
12
PLAY
7.) To Pause briefly during playback press the
button. The “ PLAY ” indicator flashes and
after a few seconds the display returns to
correct time. The sound stops, but the disc
continues to spin. Press
button again to
cancel pause and resume playback.
or
8.) To skip forward or backward to other tracks repeatedly press the
buttons until the desired track number appears in the display. Playback will
begin on the selected track.
9.) To stop playback at any time press the
button. After the last track has
played the disc stops automatically. Press the OPEN area of CD door to
open the CD door and remove your disc.
PLAY
To Start Playback From A Specific Track
Load your disc and wait until the display shows
the total number of tracks.
or
Press the
buttons to select the desired
track. While the track number is still appearing
press the
button. Playback will begin on the
selected track and continue until the end of the
disc.
High Speed Music Search
You can search rapidly forward or backward within a track to locate a specific
music passage.
or
Press and hold the
buttons to begin high speed search. The
display will show the current track and the player moves rapidly forward or
or
backward. When you reach the desired passage release the
button
and normal playback resumes.
NOTE: The volume level is automatically reduced during high speed
music search.
13
Repeat Playback
You can program the player to repeat a single track or the entire disk
continuously.
One Track Repeat
or
1. During CD disc playback, press the
buttons to select the track
to be repeated.
2. Press the REPEAT/RANDOM button until the
REP (repeat) indicator blinks. The unit will
begin playing the desired track repeatedly.
3. To cancel the setting, press the REPEAT/
RANDOM button until REP indicator is off.
PLAY
REP
All Tracks Repeat
1. During CD disc playback, press the
REPEAT/RANDOM button until the REP
(repeat) indicator light is on. The unit will
repeat all tracks.
2. To cancel the setting, press the REPEAT/RANDOM button repeatedly until
REP(repeat) indicator is off.
PLAY
Random Playback
PLAY
REP
RAN
To listen to the tracks on a disc in random order
1. During CD disc playback, press the
PEPEAT/RANDOM button repeatedly until
the RAN (random) indicator is light on. The unit will begin playing all tracks
randomly.
2. To cancel the setting, press the REPEAT/RANDOM button repeatedly until
the RAN (random) indicator is off.
14
Programmed Playback
The CD player in this unit has a 20 track programmable memory which allows
you to program any disc to play just the tracks you want to hear in the exact
order that you want to hear them. You may program a track or tracks to play
more than once if desired.
NOTE: Programming can only be done while the player is in the Stop
mode. If a disc is playing press the
button to stop playback before
performing the programming steps below.
1) Turn the unit ‘On’, to select the CD function by press FUNCTION button
repeatedly until the “cd” indicator appear on the display and load the desired
disc in the player. Wait until the player reads the disc and the display shows
the total number of tracks.
2) Press the PROG./MEM button. The PROG.
indicator will appear and the Number “1” will
show on the display, indicating that you can
select the first track to be programmed.
or
3) Press the
buttons to select the first track. The desired track
number appears and the track number will blink on the display.
4) Press the PROG./MEM button again. The selected track is entered in the
Program memory, as first programmed track. Then display advances to “2”
indicating that you can select the next track to be programmed.
5) Repeat Steps 3 and 4 to program up to 20 tracks in the memory.
6) After you have programmed all of the desired
tracks press the
button to begin
programmed playback. The PROG indicator
remains lit. Playback will begin on the first
track you programmed and continue until all
programmed tracks have been played.
As each programmed track starts playing the display will briefly show the track
number being played and then return to the correct time.
PROG
PLAY
PLAY
PROG
PLAY
PROG
PROG
AM
NOTES:
• After all programmed tracks have played the player stops but the program
remains in the memory.
Press the PROG./MEM button and then the CD PLAY/PAUSE button to
begin programmed playback again.
• To clear the programmed tracks from the memory, press the STOP
button again or open the CD door,or switching to the Radio function also
clears the program. Pressing the POWER/ALARM OFF button will shut the
unit ‘Off’,
15
Alarm Operation
Setting the ALARM Time (Wake Up time)
AM
This clock radio has two separate wake-up
alarms that can be set and used independently.
To set or adjust the wake-up times please proceed as follows:
Alarm Time Setting : Press the POWER button to off the unit, press and hold
the ALARM 1 or ALARM 2 buttons the Hour time will blink, then press the
or buttons to adjust the hour alarm time forward and backward as desired.
Press the ALARM 1 or ALARM 2 buttons again the Minutes time will blink,
and then press the
or
buttons to adjust the minute time forward and
backward as desired, then press Alarm1 or Alarm 2 button again to confirm
the alarm time. After the alarm time was set, you have to set the wake up
mode (Buzzer alarm or FM radio or AM radio or CD). To select the wake up
mode, press ALARM 1 or ALARM 2 repeatly, the display will appear "bb"
(Buzzer alarm), "r-F" (FM radio), "r-A" (AM radio), "cd" (CD alarm), "OFF"
(Alarm off) cyclically. Select your desired wake up mode. After the wake up
mode is selected, please wait for 3 seconds and the alarm setting is
confirmed.
Check the Alarm Time: During CD or radio, press the ALARM 1 or ALARM 2
buttons once to display the alarm time then the wake up alarm source will automatically show next.
NOTE: If Alarm 1 and Alarm 2 are set in same alarm time, only Alarm 1 will
sound.
AL1
Activate or Deactivate the Wake-up Mode
AL2
After you have adjusted the wake-up times on one or both alarms, you must
activate the alarms and select the wake-up mode. You have the option of waking
to the buzzer, radio or CD.
Setting the Wake Up Mode: Press the POWER button to off mode, press the
ALARM 1 or ALARM 2 buttons repeatly to select the wake-up mode. Once
the wake up mode is activated the AL1 or AL2 indicator will light on the display.
Wake to AM radio: Press the POWER button to turn on the unit, Press
Function button to select AM radio and then press
or
button to select
your desired radio station. Then press the POWER button to turn Off the unit.
Press the ALARM 1 or ALARM 2 button repeatedly until the display shows
"r-A" (wake to AM radio) and AL1 or AL2 indicator turns On. Please wait for 3
seconds, then it will automatically quit out to confirm the wake up mode setting.
Wake to FM radio: Press the POWER button to turn on the unit, Press
Function button to select FM radio and then press or button to select your
desired radio station. Then press the POWER button to turn Off the unit. Press
the ALARM 1 or ALARM 2 button repeatedly until the display shows "r-F"
(wake to FM radio) and AL1 or AL2 indicator turns On. Please wait for 3
seconds, then it will automatically quit out to confirm the wake up mode setting.
16
Wake to CD : Place a CD in the CD compartment and make sure the volume
is set as desired. Press the POWER button to off mode, press the ALARM 1 or
ALARM 2 buttons repeatedly until the display shows “cd” and AL1 or AL2
indicator turn on. Please wait for 3 seconds, then it will automatically quit out to
confirm the wake up mode setting.
Note: If there is no CD inserted, or the CD is damaged, it will automatically
wake to Buzzer.
Wake to Buzzer : Press the POWER button to off mode, press the ALARM 1 or
ALARM 2 buttons until the display shows “bb” and AL1 or AL2 indicator turn on.
Please wait for 3 seconds, then it will automatically quit out to confirm the wake up
mode setting.
Set Alarm Off : To set the alarm Off mode, Press Power button to Off the unit,
then Press ALARM 1 or ALARM 2 button repeatedly until OFF appears in the
display, wait for 3 seconds, it will automatically quit out to confirm the setting.
Turn Off Alarm
During the alarming period, press POWER or ALARM 1/2 button to shut off the
alarm, and the unit will turn on the alarm again at the same time on the follow day.
Snooze/Repeat Alarm
After the alarm turns on, you can press the
SNOOZE button for a few extra minutes sleep
(AL1 or AL2 indicator will flash). The alarm will
stop for approximately 9 minutes and then repeat.
Snooze operation can be repeated several times if desired, but after one hour
the alarm will not turn ‘On’ again.
AM
AL1
AL2
Sleep To Music Timer
You can use the sleep timer to play the Radio or CD player up to 90 minutes
and have the unit shut off automatically.
1.) Press the POWER/ALARM OFF button to turn the power ‘On’ . Operate
the Radio, AUX or CD player as usual. Adjust the VOLUME to the desired
level.
2.) Press the SLEEP button to start sleep timer
(default 90 minutes). To select your desired
sleep timer, repeatedly press the SLEEP
button, the sleep timer will count down per 10
minutes by each time pressing from 90 to 10
minutes cyclically. The SLP (Sleep) indicator will show on the display.
3.) When the display shows the desired timer, then release the SLEEP button.
The Radio or CD play will continue until the sleep timer counts down to ”00”
and then shuts the unit off automatically.
4.) To stop the Radio or CD player before the sleep timer counts down to “00”,
press the POWER / ALARMOFF button to turn the unit “Off”.
NOTE: If the sleep timer is set to CD player, the sound stops when the
disc ends, even if a longer sleep time was selected.
AM
AL1
17
SLP
Auxiliary Input Jack (Connection Cable Not Included)
This unit includes an AUX input jack to allow you to connect external devices,
such as an iPod® or portable MP3 player, and listen to the music stored on
your external device through the speakers of this unit.
Press FUNCTION button repeatly until "AU" appears in the display, then connect
the headphone jack of your external device with a connection cable to the AUX
input jack located on the front panel of this unit. The connection cable is not
included.
IMPORTANT:
Wake up alarm is not available for AUX in function.
After connecting your external device to the AUX input jack, slowly
adjust both the volume controls on this unit and your external device to
find the desired setting. Please note that if the VOLUME control on your
external device is set too high, the sound will be distorted.
18
Headphone (PHONES) Jack
This unit includes a 3.5mm PHONES (headphone) jack on the front panel. This
allows you to connect a set of stereo headphones (not included) for private
listening without disturbing others. When headphones are connected, the
built-in speakers are automatically disconnected.
IMPORTANT! When using stereo headphones always set the volume control
to a low level before you put on the headphones. Then put on the
headphones and gradually adjust the volume control to the desired level.
Remember that prolonged listening with headphones or ear buds at high
volume levels may eventually cause hearing loss
19
CARE AND MAINTEANCE
Compact Disc Care
• To remove a disc from its storage case, press down on the center of the case
and lift the disc out, holding it carefully by the edges.
• Fingerprints and dust should be carefully wiped off the disc’s recorded
surface with a soft cloth. Unlike conventional records, compact discs have no
grooves to collect dust and microscopic debris, so gently wiping with a soft
cloth should remove most particles. Wipe in a straight line from the inside to
the outside of the disc. Small dust particles and light stains will have
absolutely no effect on reproduction quality.
• Clean the disc periodically with a soft, lint-free, dry cloth. Never use
detergents or abrasive cleaners to clean the disc. If necessary, use a CD
cleaning kit.
• Never write on or affix labels to the surface of compact discs.
Care Of The Cabinet
• If the cabinet becomes dusty wipe it with a soft dry dust cloth. Do not use any
wax or polish sprays on the cabinet.
• If the front panel becomes dirty or smudged with fingerprints it may be
cleaned with a soft cloth slightly dampened with a mild soap and water
solution. Never use abrasive cloths or polishes as these will mar the finish of
your unit.
Caution
Never allow any water or other liquids to get inside the unit while cleaning.
20
TROUBLE SHOOTING GUIDE
Symptom
Radio
Noise or sound distorted
on AM or FM broadcasts.
AM or FM, no sound.
Compact Disc Player
CD Player will not play.
CD skips while playing.
Possible Cause
Solution
Station not tuned properly
for AM or FM.
AM: The bar antenna is
not positioned correctly.
Volume at minimum.
Retune the AM or FM
broadcast station.
Reposition the unit until
best reception is obtained.
Increase Volume.
CD is not installed or Insert CD with label side
installed incorrectly.
up.
Disc is dirty or scratched. Wipe disc with cloth or
use another disc.
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE
PLEASE CALL:
1-800-898-9020 OR
1-800-695-0098 OR
E-MAIL TO: [email protected]
21
The Serial Number can be found on the bottom of the unit. We Suggest
that you record the Serial Number of your unit in the space below for
future reference.
CKD9918
22
TM
CKD9918-001-01
Made In China
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement