Izzi single lever side action monobloc sink mixer

Izzi single lever side action monobloc sink mixer tubular spout
Monobloc sink mixer
Monobloc sink mixer
Size
Pattern No.
Pack 1 Qty
Pack 2 Qty
Code
Barcode
Price (£) ex VAT test
N/A
Monobloc Sink Mixer
1
4
4G4098
5013866083709
£109.26
Code
4G4098
Description
Dimensions
Monobloc Sink Mixer
See Image
Pegler Yorkshire reserve the right to change specifications
10 Year Guarantee
Luxury Taps and Mixers
Pegler Yorkshire Customcare 10 Year Guarantee - Terms and Conditions
Product are subject to a 10 year guarantee that is between Pegler Yorkshire and the final purchaser of the
product.
The guarantee is subject to proof of purchase being supplied.
This guarantee does not affect any statutory rights the consumer may have in law.
The guarantee covers manufacturing or material defects and does not cover parts subject to normal wear
and tear.
Finishes other than chrome are covered for a period of 3 years only and the guarantee on the finish is
subject to the cleaning instructions being followed.
The guarantee is not applicable where the product is fitted contrary to the conditions in the fitting
instructions.
Abusive behaviour and accidental damage to the product are not covered by this guarantee.
The extent of this liability is limited to the cost of the replacement of the defective item and not to fitting or
consequential damages.
Care
To maintain the surface finish, simply wipe occasionally with a mild detergent on a soft damp cloth. Dry,
using a soft cloth. Never use abrasive cleaners or chemical household cleaners and avoid contact with
concentrated bleach.
Maintenance
No regular maintenance is required for this product.
In case of complete replacement Pegler recommend service valves should be fitted to the supply inlets.
For any further help or replacement parts please contact the Service Support Team on 0800 1560050.
Regulations
It is important to ensure that the water supplies to your taps and mixers are connected in accordance with
the water regulations (WRAS) requirements and good plumbing practice.
It is Pegler’s recommendation and good plumbing practice that the supplies of hot and cold water to the
mixer should be at equal (balanced) pressures in order to provide a consistent flow. Supplies should be
from a common source, either mains or tank fed. If supplies are not equal pressures then non return valves
should be fitted.
Monobloc sink mixer
Spare Key
Description
Code
Barcode
1
HD130 Handle
854578
5022050329462
Spare Key
Description
Date From
Date To
Price (£) ex VAT
01/01/1900
To Current
£48.77
1
Code
Barcode
Date From
Date To
Price (£) ex VAT
01/01/1900
To Current
£2.98
2
2
Spare Key
IN20 Indice
854562
Description
5022050330833
Code
Barcode
Date From
Date To
Price (£) ex VAT
3
3
HKS29 Headwork Shroud
854579
5022050329509
01/01/1900
To Current
£11.90
Spare Key
Description
Code
Barcode
Date From
Date To
Price (£) ex VAT
01/01/1900
To Current
£17.50
Date From
Date To
Price (£) ex VAT
01/01/1900
To Current
£53.12
4
4
HKS28 Headwork Shroud
Spare Key
Description
854520
5022050247124
Code
Barcode
5
5
HK101 Headwork Cartridge
854518
5022050247018
Spare Key
Description
Code
Barcode
6
FP55 FIXING PACK
854407
5013866080050
Date From
Date To
Price (£) ex VAT
01/01/1900
To Current
£14.11
6
Spare Key
Description
Code
Barcode
Date From
Date To
Price (£) ex VAT
01/01/1900
To Current
£7.82
7
7
Spare Key
OA7 Sink Outlet
854589
Description
5022050330277
Code
Barcode
Date From
Date To
Price (£) ex VAT
01/01/1900
To Current
£83.70
8
8
Spare Key
SPT42CP Spout Assembly
Description
854810
Code
5022050351869
Barcode
Date From
Date To
Price (£) ex VAT
01/01/1900
To Current
£5.95
9
9
SK24 Head Seal Kit
854580
5022050329578
Spare Key
Description
Code
Barcode
10
IT3 INLET TAILS PAIR (Copper)
812100
5013866055614
Date From
Date To
Price (£) ex VAT
01/01/1900
To Current
£27.93
Date From
Date To
Price (£) ex VAT
01/01/1900
To Current
£5.57
10
Spare Key
Description
Code
Barcode
11 not shown
BN12 SUPPORT BACKNUT
854463
11 not shown
Pegler Yorkshire Group Ltd, St Catherine's Ave, Doncaster, S Yorkshire, DN4 8DF
Telephone: Phone +44 (0) 844 243 4400 Fax: +44 (0) 844 243 9870 Website: www.pegleryorkshire.co.uk
Registered office : Pegler Yorkshire Group Ltd, St Catherine's Ave, Doncaster, S Yorkshire, DN4 8DF Company no : 00401507
5013866084904
Water Regulations Requirements
It is important to ensure that the water supplies to your taps and mixers are connected in
accordance with the water regulations (WRAS) requirements and good plumbing practice.
80mm
84mm
It is Pegler's recommendation and good plumbing practice that the supplies of hot and cold
water to the products should be at equal (balanced) pressures in order to provide a consistent
flow. Supplies should be from a common source, either mains or tank fed. If supplies are not
equal pressures then non return valves should be fitted (supplied).
106mm
27mm
31mm
41mm
231mm
max thickness of
ware/worktop 44
78mm
69mm
352mm
54mm
116mm
½”Basin Taps
¾” Basin Taps
max thickness of
ware/worktop 44
SL Mono Basin
Pipe Connections
180mm
IMPORTANT . Before making any inlet pipe connections all supplies MUST be thoroughly
flushed to remove any debris. Failure to do so could result in damage or low flow from the
mixing valve. It is a requirement of Byelaw 55 of the Water Fittings Byelaw Scheme that this
function is undertaken before making any pipe connections to supplies.
Bath Filler
General Installation Notes
• Care must be taken during installation to prevent any risk of damage to the product or
Injur y to installer.
• Installation must be carried out by a qualified and competent person and in accordance
with the instructions supplied.
• Installations must comply with all Local and National Water Authority Regulations, and
Building/Plumbing Regulations.
• Please ensure that you have read and understood all sections of this manual before
Installation.
213mm
S/A Mono Sink Mixer
108mm
70mm
Water Supply Pressures
47mm
max thickness of
ware/worktop 44
max thickness of
ware/worktop 44
153mm
65mm
168mm
35mm
115mm
115mm
96mm
DC Mono Basin
Please Note : If a pump is to be installed to boost gravity supplies please refer to the pump
manufactures instructions.
The hot and cold inlets for any of the products are hot on the left and cold on the right when
viewed from the front of the fitting. It is our recommendation and good plumbing practice that
a ser vice valve also (Pegler PB300) should be installed upstream in the inlet supply lines.
125mm
86mm
This products has been designed to function on all types of water systems
max thickness of
ware/worktop 44
180mm
Leger fittings have been designed to function under the following conditions:
• Minimum supply pressure 0.1 bar.
• Maximum supply pressure 6.0 bar.
Generous flow rates are achieved at pressures as low as 0.1 bar. At high pressures it may be
necessar y to reduce excessive flow rates by fitting stop or ser vicing valve in the supply line
before the mixer or tap. These stop valves facilitate ease of maintenance should it be Necessar y.
Please Note : The mono basin mixer L565 is supplied with flow straightener fitted and an
alternative aerator nozzle packed separately which can be fitted at high pressures to reduce
Splashing.
Installation
Pillar Taps
i)
ii)
SL Mini Mono Basin
237mm
Mono Sink Mixer
Bath Shower Mixer
iii)
Remove backnut from tap tail.
Fit tap through ware ensuring anti-rotational washer is trapped in position
Between tap base and ware, replace backnut and tighten.
Thoroughly flush pipework and connect to tap. Hot should be on the left and cold
On the right when viewing pipework from the front.
Mono Sink / Side Action Mono Sink Mixer
i)
Screw inlet tails into body and tighten up ensuring washer seal is firmly in place to
prevent any leaks.
Please note: For standard mono sink go to point (iv)
ii)
For Side Action Mono Sink Mixer – Locate the handle from the box and remove the
indice (plastic bung) from under the lever part of the handle. Locate the handle onto
the square spindle of the exposed cartridge, then using the Allen Key provided screw
the grub screw (packaged with the clamping kit) into the handle and tighten onto the
cartridge.
Please note: The handle should be positioned pointing towards you (when viewing the tap
from the front) for its natural off position!
iii)
Once in position relocate the indice (plastic bung) into the hole under the lever,
ensuring the red and blue printed on the indice is the correct way around.
iv)
Screw in the clamping stud into the body and position rubber seal under the base of
the mixer, the n position the mixer into the ware in desired position ensuring lever
movement is not obstructed.
v)
Please note: Ensure free movement of spout is adequate before clamping in position.
vi)
To tighten the mixer to the ware, Firstly, place clamping plate rubber then the steel
clamping Plate onto the stud, then secure by screwing tight the clamping nut. Re
check the mixer position above the ware and ensure the spout still rotates freely.
vii)
Connect inlets to supplies, (Fit non return valves if system is imbalanced
B ath F iller / B ath S hower M ixer
i)
Remove backnuts from inlet tails and fit tails through tap holes of bath ensuring base
rubber is trapped between bath and fitting. Replace and tighten backnuts from
beneath bath.
ii)
Thoroughly flush pipework and connect tap to the supplies ensuring hot is on the left
and cold on the right when viewing the mixer from the front.
iii)
Fit shower hose and kit to the bath mixer.
iv)
For all brassware supplied wi thout handles, see separate handles instructions.
v)
For ser vicing or handle realignment the brassware supplied will be:
•
Snap on (push on –pull off )
•
Fixed with a locating screw
•
Fixed handle and spindle
vi)
Fixing the kit to Bath Shower mixers
•
Mark the holes and drill with 6mm bore
•
Insert plugs and fasten screw
•
Click on the shell and connect the shower hose
M ono b loc B asin M ixer
Pegler Basin mixers are supplied with separate inlet tails. M12 flexible tails 12”long
i)
screw inlet tails into body and tighten up ensuring ‘O’ring seal is firmly in place and
leak proof, unless pre fitted securing studs to be fitted and tighten
Ii)
Locate seal under flange (or base of monobloc).
iii)
Place fittings through hole in ware. Place washer over inlet tails and position on
underside of ware. Place clamping plate on threaded stud/s ensuring that stud is
positioned in the slot inthe clamping plate and that the inlet tails are positioned in
the cut out. Place fixing nut onto threaded studs and loosely tighten firmly up the
base of Ware / worktop.
iv)
Insert click waste
v)
Ensure pipework is thoroughly flushed to remove debris before connecting to the
fitting,
Connect to the water supplies.
i)
Ensure that the O ring seals are fitted correctly in their grooves screw the tails into the
body.
To fit handles (Where applicable)
To fit handle place snap fit connector
(A) onto spline of headwork
(B) and screw down firmly using screw provided
(C). Place handle
(D) over connector and push firmly until it snaps home.
You r Guide to the i nstallation, Care and maintenance of
Izzi
Care & Maintenance
To maintain the surface finishes, simply wipe occasionally with a mild detergent on a soft damp
cloth. Dr y using a soft cloth, never use abrasive cleansers or chemical household cleaners, and
avoid contact with concentrated bleach. Applause products are manufactured to the highest of
standards and should require little or no maintenance. In the unlikely event of any spare part
requirements, please contact your nearest stockist or the Pegler Sales Office, St Catherine’s
Avenue, Doncaster. DN4 8DF, Telephone 01302 368581.
½”Basin Taps
¾”Basin Taps
SL Mini Mono Basin
SL Mono Basin
To maintain the surface finishes, simply wipe occasionally with a mild detergent on soft damp
cloth. Dr y using soft cloth, never use abrasive cleaners or chemical household cleaners, avoid
contact with concentrated bleach.
Pegler products are manufactured to the highest standards and should require little or no
maintenance. In the unlikely event of any spare part requirements, please visit our website:
www.pegler.co.uk , contact you’re nearest stockist or the Pegler Technical Office on telephone
0870 1200285
Customer Reference Data
DC Mono Basin
Date of Purchase…………………………………………………… ………………………………………………
Mono Sink Mixer
Supplier……………………………………………………………… …………………………………………………
Supplier Tel. No……………………………………………………… ……………………………………………..
Model Type…………………………………………………………..………………………………………………..
Serial No……………………………………………………………… ………………………………………………..
Installer………………………………………………………………….……………………………………………...
.
Installer Contact Details………………………………… ………… ………………………………………....
Bath Filler
Pegler Limited, St Catherine’s Avenue, Doncaster DN4 8DF
Telephone 01302 560560, Fax 01302 560109
Deck Bath
Shower Mixer
S/A Mono Sink Mixer
Pegler Limited, St Catherine’s Avenue, Doncaster DN4 8DF
Telephone 01302 560560, Fax 01302 560109