查询FCPS-24S6供应商
捷多邦,专业PCB打样工厂,24小时加急出货
July 20, 2004
DN-6927 • E-30
FCPS-24S6 and FCPS-24S8
6-Amp and 8-Amp
24-Volt Remote Power Supplies
Section: Power Supplies
GENERAL
The FCPS-24S6 (6-amp) and FCPS-24S8 (8-amp) are compact, cost-effective remote power supplies with battery charger.
The FCPS-24S6/-24S8 may be connected to any 12- or 24volt Fire Alarm Control Panel (FACP) or may be used as a
stand-alone supply. Primary applications include Notification
Appliance (bell) Circuit (NAC) expansion (to support ADA requirements and NAC synchronization) or auxiliary power to
support 24-volt system accessories. The FCPS-24S6/-24S8
provides regulated and filtered 24 VDC power to four notification appliance circuits configured as either four Class B (Style
Y) or Class A (Style Z, with ZNAC-4 option module). Alternately, the four outputs may be configured as all non-resettable,
all resettable, or two non-resettable and two resettable. The
FCPS-24S6/-24S8 also contains a battery charger capable of
charging up to 18 AH batteries.
California
State Fire
Marshal
7315-0028:225
S635
MEA
299-02-E
• UL-Listed NAC synchronization using System Sensor,
Wheelock, or Gentex “Commander²” appliances.
• Cascadable for up to ten power supplies (four for Gentex)
with strobe timing maintained.
• Operates as a “sync follower” or as a “sync generator” (default). See note on page 2.
• Contains two fully-isolated input/control circuits — triggered
from FACP NAC (NAC expander mode) or jumpered permanently “ON” (stand-alone mode).
• Four Class B (Style Y) or four Class A (Style Z, with ZNAC-4
module) NACs.
• 6-amp (FCPS-24S6) or 8-amp (FCPS-24S8) full load output,
with 3 amps maximum/circuit, in NAC expander mode (UL 864).
• 4-amp (FCPS-24S6) or 6-amp (FCPS-24S8) continuous output in stand-alone mode (UL 1481).
• Compatible with coded inputs; signals passed through.
• Optional power-supervision relay (A77-716B).
• In stand-alone mode, output power circuits may be configured as: resettable (reset line from FACP required), nonresettable, or a mix of two and two.
• Fully regulated and filtered power output — optimal for powering four-wire smoke detectors, annunciators, and other
system peripherals requiring regulated/filtered power.
• Power-limiting technology meets UL power-limiting requirements.
• Form-C normally-closed trouble relay.
• Fully supervised power supply, battery, and NACs.
• Selectable earth fault detection.
• AC trouble report selectable for immediate or 8-hour delay.
• Works with virtually any UL 864 fire alarm control which utilizes an industry-standard reverse-polarity notification circuit (including unfiltered and unregulated bell power).
• Requires input trigger voltage of 9.0 – 32 VDC.
• Self-contained in compact, locking cabinet — 15" (38.1 cm)
high x 14.5" (36.83 cm) wide x 2.75" (6.985 cm) deep.
• Includes integral battery charger capable of charging up to 18
AH batteries. Cabinet capable of housing 7.0 AH batteries.
6827pho1.jpg
FEATURES
• Battery charger may be disabled via DIP switch for applications requiring larger batteries.
• Fixed, clamp-type terminal blocks accommodate up to 12
AWG (3.1 mm²) wire.
STANDARDS and CODES
The FCPS-24S6/-24S8 complies with the following standards:
• NFPA 72 National Fire Alarm Code.
• UL 864 Standard for Control Units for Fire Alarm Systems
(NAC expander mode).
• UL 1481 Power Supplies for Fire Alarm Systems (standalone mode).
SPECIFICATIONS
Primary (AC) power:
• FCPS-24S6/-24S8: 120 VAC, 60 Hz, 3.2 A maximum.
• Wire size: minimum #14 AWG (2.0 mm²) with 600 V insulation.
Control input circuit:
• Trigger input voltage: 9 to 32 VDC.
• Trigger current: 2.0 mA (16 – 32 V). Per input: 1.0 mA (9 –
16 V).
Trouble contact rating: 5 amps at 24 VDC.
NOTIFIER® is a Honeywell company.
This document is not intended to be used for installation purposes. We try to keep our
product information up-to-date and accurate. We cannot cover all specific applications
or anticipate all requirements. All specifications are subject to change without notice.
For more information, contact NOTIFIER. Phone: (203) 484-7161 FAX: (203) 484-7118
12 Clintonville Road, Northford, Connecticut 06472
Auxiliary power output: specific application power 500 mA
maximum.
Output circuits:
• +24 VDC filtered, regulated.
• 3.0 amps maximum for any one circuit.
• Total continuous current for all outputs (stand-alone mode):
for FCPS-24S6: 4.0 amps maximum; for FCPS-24S8: 6.0
amps maximum.
• Total short-term current for all outputs (NAC expander mode):
for FCPS-24S6: 6.0 amps maximum; for FCPS-24S8: 8.0
amps maximum.
Secondary power (battery) charging circuit:
• Supports lead-acid batteries only.
• Float-charge voltage: 27.6 VDC.
• Maximum charge current: 1.5 amps
• Maximum battery capacity: 18 AH.
APPLICATIONS
Example 1: Expand notification appliance power an additional 6.0 amps (FCPS-24S6) or 8.0 amps (FCPS-24S8). Use
up to four Class B (Style Y) outputs or four Class A (Style Z)
outputs (using ZNAC-4). For example, the FACP notification
appliance circuits will activate the FCPS when reverse-polarity activation occurs. Trouble conditions on the FCPS are
sensed by the FACP through the notification appliance circuit.
Example 2: Use the FCPS to expand auxiliary regulated
24-volt system power up to 4.0 amps (FCPS-24S6) or up to
6.0 amps (FCPS-24S8). Both resettable and non-resettable
power options are available. Resettable outputs are created
by connecting the resettable output from the FACP to one or
both of the FCPS inputs.
Example 3: Use addressable control modules to activate
the FCPS instead of activating it through the FACP notification
appliance circuits. This typically allows for mounting the FCPS
at greater distances* away from the FACP while expanding
system architecture in various applications.
For example, an addressable control module is used to activate the FCPS, and an addressable monitor module is used to
sense FCPS trouble conditions. Local auxiliary power output from
the FCPS provides power to the
addressable control module.
SYNC FOLLOWER/GENERATOR NOTE
In some installations, it is necessary to synchronize the flash
timing of all strobes in the system for ADA compliance. Strobes
accomplish this by monitoring very short timing pulses on the
NAC power which are created by the FACP. When installed at
the end of a NAC wire run, the FCPS-24S6/-24S8 can track
(i.e., “follow”) the strobe synchronization timing pulses on the
existing NAC wire run. This maintains the overall system flash
timing of the additional strobes attached to the FCPS.
When the FCPS-24S6/-24S8 is configured (via DIP switch settings) as a “sync follower,” the FCPS’s NAC outputs track the
strobe synchronization pulses present at the FCPS’s sync input terminal. The pulses originate from an upstream FACP or
other power supply.
When the FCPS-24S6/-24S8 is configured (via DIP switch settings) as a “sync generator,” the FCPS’s sync input terminals
are not used. Rather, the FCPS is the originator of the strobe
synchronization pulses on the FCPS’s NAC outputs. In “sync
generator” mode, the sync type (System Sensor, Wheelock,
or Gentex) is selectable via DIP switch settings.
PRODUCT LINE INFORMATION
FCPS-24S6: 6.0 amp, 120 VAC remote charger power supply. Includes main printed circuit board, transformers, enclosure (15" [38.1 cm] high x 14.5" [36.83 cm] wide x 2.75" [6.985
cm] deep), and installation instructions.
FCPS-24S8: 8.0 amp, 120 VAC remote charger power supply. Includes main printed circuit board, transformers, enclosure (15" [38.1 cm] high x 14.5" [36.83 cm] wide x 2.75" [6.985
cm] deep), and installation instructions.
ZNAC-4: Class A (Style Z) NAC option module.
A77-716B: 12/24 VDC end-of-line relay for monitoring fourwire smoke detector power.
BAT-1270: Battery, 12 volt, 7.0 AH (two required, see BAT
Series data sheet DN-6933).
PS-1270: Battery, 12 volt, 7.0 AH (two required, see PS
Series data sheet DN-1109).
*Addressable FACPs are capable
of locating control and monitor
modules at distances of up to
10,000 feet (3048 meters).
AGENCY LISTINGS
AND APPROVALS
See the first page of this data
sheet for listing agencies and file
numbers. These listings and approvals apply to the FCPS-24S6
and the FCPS-24S8. In some
cases, certain modules or applications may not be listed by certain approval agencies, or listing
may be in process. Consult factory for latest listing status.
6827blok.wmf
SIMPLIFIED
BLOCK DIAGRAM
BOARD LAYOUT
6827bord.wmf