Quick start guide
PERSONAL COMFORT SETTINGS
SHAVER 9500 / SHAVER 9300
1
2
CHARGING
1
2
3
UNPLUG
SHAVING
1
2
3
1 hr.
4
S9531
S9311
QUICK CHARGE
1X
Rechargeable Cordless
Tripleheader Shaver
Question?
Contact
Philips
Norelco
Always here to help you
Register your product and get support at
www.norelco.com/register
WET SHAVING
5 min.
1
2
4
5
3
CLEANING SHAVER
TRIMMING
1
2
1
4
3
3
PREPARING SMARTCLEAN SYSTEM
1
±4 hrs.
3
4
2
10 min.
4
2
1
2
4
2
2
1
3
1
TRAVEL LOCK
1
2
5
3 sec.
QUESTIONS?
See user manual or
www.philips.com/norelco
1
3 sec.
ENGLISH 4
Congratulations on your purchase and
welcome to Philips Norelco!
S9531/S9311
To fully benefit from the support that Philips
Norelco offers, register your product at
www.norelco.com/register
4
ENGLISH
IMPORTANT SAFETY
INSTRUCTIONS
When using an electric appliance, basic precautions should
always be followed, including the following:
Read all instructions before using this appliance.
DANGER
To reduce the risk of electric shock:
1. Do not reach for a corded shaver/SmartClean System that
has fallen into water. Unplug immediately.
2. Power plug and the accessories connected to it are not for
immersion or for use in shower.
3. Do not use an extension cord with this appliance.
4. Do not place or store a SmartClean System where it can
fall or be pulled into a tub or sink. Do not place or drop a
SmartClean System into water or other liquid.
5. Always unplug this shaver/SmartClean System from the
electrical outlet immediately after use, except when shaver/
SmartClean System is (re)charging.
6. Unplug and remove power supply cord from shaver
before cleaning.
7. The batteries used in this device may present a fire or
chemical burn hazard if mistreated. Do not disassemble, heat
above 100ºC (212°F) or incinerate.
WARNING
To reduce the risk of burns, fire, electric shock, or
injury to persons:
ENGLISH
5
1. Close supervision is necessary when this shaver/SmartClean
System is used by, on, or near children or invalids.
2. Use this shaver/SmartClean System for its intended
household use as described in this manual. Do not use
attachments or a cleaning cartridge not recommended by
Philips Electronics North America Corporation.
3. Never operate this shaver/SmartClean System if it has a
damaged cord or charging plug, if it is not working properly,
if it has been dropped or damaged, or dropped into water
while plugged in. For assistance call 1-800-243-3050.
4. Keep the shaver/SmartClean System, cord and charging plug
away from heated surfaces.
5. Never drop or insert any object into any opening.
6. Do not use the adapter in or near a power outlet that
contains an electric air freshener to prevent damage to the
adapter.
7. Do not clean, charge or plug in shaver/SmartClean System
outdoors or operate where aerosol (spray) products are
being used or where oxygen is being administered.
8. Do not use this shaver with a damaged or broken comb, as
facial injury may occur.
9. Always attach plug to shaver/SmartClean System first, then
plug into outlet and then put razor in SmartClean System.
Be certain plug is inserted firmly into shaver, up to mark
indicated on plug. To disconnect, turn SmartClean System
off, remove charging plug from outlet.
10.Never put the shaver/SmartClean System in direct sunlight
or store at a temperature above 140°F (60°C).
11.Keep the cord dry at all times. Do not handle with wet
hands.
12.To prevent possible damage to the cord, do not wrap cord
around the shaver/SmartClean System.
13.Do not attempt to open the appliance to replace the
battery.
6
ENGLISH
14.Only use the power plug and other accessories supplied
with the appliance.
SAVE THESE
INSTRUCTIONS
IMPORTANT: The power plug contains a transformer. Do
not cut off the power plug to replace it with another plug, as
this will cause a hazardous condition.
45 - DAY MONEY-BACK GUARANTEE
To enjoy the closest and most comfortable shave from your new Philips Norelco
Men’s Shaver, the shaver should be used exclusively for 3 weeks. This allows your
hair and skin enough time to adapt to the Philips Norelco Shaving System. If, after
that period of time, you are not fully satisfied with your Philips Norelco Men’s
Shaver, send the product back along with dated sales receipt and we’ll refund
you the full purchase price. The shaver must be shipped prepaid by insured
mail, insurance prepaid, have the original sales receipt, indicating purchase price, the date of purchase, and the money-back guarantee return
authorization form enclosed. We cannot be responsible for lost mail.
The shaver must be postmarked no later than 45 days from the date of purchase.
Philips Norelco reserves the right to verify the purchase price of the shaver and
limit refunds not to exceed suggested retail price.
To obtain money-back guarantee return authorization form,
call 1-800-243-3050 for assistance. Delivery of refund check will
occur 6–8 weeks AFTER receipt of returned product.
ENGLISH
Table of Contents
Features ...................................................... 8-10
Multi-Level Display ................................12-14
Charge Meter ...............................................14
Before First Use ...........................................15
Charging ...................................................15-17
Recharging .....................................................17
Quick Charge ...............................................18
Put It To The Test & Shaving Tips ..............18
How to Shave
With An Electric Shaver .......................19-21
Trimming ..................................................21-23
Travel Lock ..............................................23-24
Cleaning ....................................................24-31
Replacing the Shaving Unit ..................32-35
Maintenance ..................................................36
Storage............................................................36
Assistance ......................................................37
Disposal ..........................................................37
Accessories ...................................................38
Warranty ........................................................39
7
8
ENGLISH
ENGLISH
9
Features
Contour Detect Technology
Shaving Unit
• Hair Chamber
captures shaven
hair
Electronic
On/Off Button
Personal Comfort
Settings Bar
Cleaning
Indicator
Travel Lock
Multi-Level Display
• Shows
remaining power
level of battery
• Battery Charge,
Full & Low
Indicators
Replacement
Shaving Unit
Indicator
Blocked Shaving
Heads Indicator
Click-on Precision
Trimmer
Automatic Worldwide
Voltage 100V to 240V AC
Travel Pouch
Retaining Ring Holder
Rechargeable 1-hour full
charge for up to 50 min.
of cordless shaving time
Quick Charge
Cordless - To shave
without a cord
Full 2-Year Warranty
45-Day Money-Back
Guarantee
10
ENGLISH
11
Features
SmartClean System
SmartClean System Cap
Shaver Holder
On/Off Button
Cleaning
Cartridge
Replacement
Indicator
Cleaning
Indicator
Drying
Indicator
Cleaning
Cartridge
Release Button
Ready Indicator
Charging
Indicator
Cleaning Cartridge
12
ENGLISH
ENGLISH
Multi-Level Display
Remove any sticker or protective foil from
C ◗ the
display before using shaver.
The display provides the following information:
◗ Charging Indicator
-As soon as you connect the power cord to
an electrical outlet, you will hear a beep and
the bottom charging light blinks. As charging
continues, more and more lights will blink to
indicate what level the battery has been charged.
-Quick charge: When the shaver contains enough
energy for one shave, the bottom charging light
lights up white continuously.
C
◗ Full Charge Indicator
the battery has been fully charged,
C -When
all charging lights light up continuously.
After approximately 30 minutes the display
automatically switches off again.
- If the on/off button is pressed during or after
charging, the shaver will beep indicating the
shaver is still connected to the electrical outlet.
C
◗ Remaining Battery Capacity
-The remaining battery capacity is indicated by
the number of charging lights that are on.
13
◗ Low Battery Indicator
the battery is almost empty (5 or less
C -When
shaving minutes left), the bottom charging light
blinks orange and you will hear a beep.
Personal Comfort Settings
C ◗Choose
between three speed settings that best
fit your skin and hair type: slow for a more skinfriendly shave, normal for a thorough shave and
fast for a high powered shave. Press the – or +
buttons to select your personal comfort settings.
Replacement Shaving Unit Indicator
C ◗Every
year, depending on your shaving behavior,
the replacement shaving unit indicator lights up
white continuously, the arrows blink white and
you will hear a beep. See 'Replacing the Shaving
Unit' section for instructions to reset the shaver.
This reminds you that with new shaving heads
you will guarantee yourself optimal shaving
performance.
Blocked Shaving Heads Indicator
C ◗If the
display shows a blinking replacement
shaving unit and faucet, an orange exclamation
mark and the shaver beeps, clean the shaver
thoroughly before continuing to shave (see
‘Cleaning’). After cleaning, if the blinking
replacement shaving unit and faucet with
exclamation mark remain on the display,
immediately replace the shaving unit (see
‘Replacing the Shaving Unit’).
14
ENGLISH
ENGLISH
Before First Use
Indicator
C ◗ForCleaning
optimal shaving performance, we
◗ Charge the shaver before you start using it
(see ‘Charging’). Make sure the shaver is
switched off before you start charging it.
◗ Remove any sticker or protective foil from
the display before using shaver.
recommend cleaning the shaver after EACH use.
The blinking faucet will remind you the
shaving unit needs to be cleaned. This happens
after each shave.
◗ Travel Lock
The shaver is equipped with a travel lock function.
You can use the travel lock function when you are
going to store the shaver for a longer period or if
you are going to take the shaver with you when
traveling. See ‘Travel Lock’ section for instructions
on how to use this function.
Charge Meter
◗ Charge Meter monitors amount of remaining
battery power available. Remaining battery
capacity is based on the amount of power
consumed shaving per minute and is
dependent upon your skin and beard type,
whether you use pre-shave lotion, and how
often the trimmer is used.
◗ Initially your shaver may need to go through 2
or 3 full charge/recharge cycles before
remaining battery capacity indicators begin to
display your accurate battery power left.
15
Important
◗ Only use the power cord or SmartClean
System provided to charge the shaver.
◗ The power plug transforms 100-240V AC to
less than 24V DC.
Charging
◗ Charging, recharging or storing at
temperatures below 40ºF/4,5ºC or higher
than 95ºF/35ºC adversely affects lifetime of
batteries.
◗ Charging or recharging requires one full hour.
◗ A fully charged shaver has a shaving time of up
to 50 minutes.
◗ You may recharge when the display indicates
the battery is almost empty.
◗ This shaver will not operate corded directly
from the electrical outlet.
◗ Do not charge shaver in a pouch.
16
ENGLISH
C
ENGLISH
1
2
1
C
Connect cord directly to shaver (1) and
connect the power plug into any 100V to
240V AC outlet (2). Use only the power
cord provided.
◗ An adaptor plug may be necessary for power
cord usage in some foreign countries. Use
an attachment plug adaptor of the proper
configuration for the power outlet.
3
1
C
2
The power cord will automatically convert to
work on 100V to 240V AC systems.
2
The display on the shaver will indicate
shaver is charging.
3
Charging requires one full hour. A fully
charged shaver has a cordless shaving time
of up to 50 minutes.
1
Charging Shaver with SmartClean
System
1
C
2
Connect the small plug to the SmartClean
System. Connect the power plug into any
100V to 240V AC outlet. Use only the
power cord provided.
Press the top cap to open the SmartClean
System.
3
C
3
17
Hold the shaver head side down above the
shaver holder.
Place the shaver into the holder (1), push
shaver back (2) and press down the top
cap to connect the shaver (3) (click).
The shaver will only fit in the SmartClean System
in one direction.
4
5
The battery and on/off symbol blinks to
indicate the shaver is charging.
6
Charging requires one full hour. A fully
charged shaver has a cordless shaving time
of up to 50 minutes.
7
Press the top cap (1), pull the shaver
forward (2) and lift shaver from holder (3).
2
Recharging
1
Recharging requires one full hour.
Recharge when the display indicates the
battery is almost empty.
18
ENGLISH
ENGLISH
Quick Charge
When batteries are totally depleted, recharging
the shaver for approximately 3-5 minutes gives
enough energy for a 3-minute cordless shave.
Put It To The Test & Shaving Tips
◗ 21 Day Trial and Conversion Process. It is a fact
that your skin and beard need time to adjust to
a new shaving system.
◗ Use your new shaver exclusively for 3 weeks to
fully enjoy the closeness of a Philips Norelco
shave.
◗ At first you may not get as close a shave as you
expect, or your face may even become slightly
irritated. This is normal since your beard and
skin will need time to adjust. Invest 3 weeks
and you’ll soon experience the full joy of your
new shaver.
◗ Stick with it! If you alternate shaving methods
during the adjustment period, it may make it
more difficult to adapt to the Philips Norelco
shaving system.
◗ If you are still not convinced after 21 days,
Philips Norelco will refund you the full
purchase price as long as the request is
received within 45 days of purchase.
19
How To Shave With An Electric Shaver
C ◗ This symbol on the shaver indicates that the
shaver can be used in the bath or shower.
◗ Make sure the SmartClean System does not
get wet or near water.
◗ For hygienic reasons, the shaver should only
be used by one person.
◗ Use this shaver for its intended household use
as described in this manual.
Shaving
◗ For best results pre-trim your beard if you
have not shaved for 3 days or longer.
C
Turn shaver ON by pressing the on/off
button once. Shave against the direction
of beard growth using only circular
movements.
The shaver display will light up briefly.
1
BSelect your personal comfort setting before
using shaver. (See 'Multi-Level Display' chapter).
2
Stretch your skin with your free hand so
blades can lift and cut whiskers. Gently
press shaver to skin so the floating heads
can follow the contours of your face.
DO NOT press too hard. Too much
pressure can pinch the skin into the combs.
20
ENGLISH
ENGLISH
Turn shaver OFF by pressing the on/off
button once.
The display lights up for a few seconds and then
shows the remaining battery capacity.
3
C
4
Clean the shaver after each use (see
chapter ‘Cleaning’).
5
Place the shaver in the SmartClean System
to protect shaver heads.
Wet Shaving
You can also use the shaver on a wet face with
shaving foam or gel.
C
1
C
5
21
Move the shaving heads in circular
movements over your skin.
NOTE: Rinse the shaver under the tap regularly
to ensure that it continues to glide smoothly over
your skin.
Dry your face and thoroughly clean
the shaver after each use (see chapter
‘Cleaning’).
NOTE: Make sure you rinse all foam or gel off the
shaver.
6
C
7
Apply some water to your skin.
Place the shaver in the SmartClean System
to protect heads.
Trimming
C
2
Apply shaving foam or gel to your skin.
3
Rinse the shaving unit under the tap
to ensure that the shaving unit glides
smoothly over your skin.
4
Press the on/off button once to switch on
the shaver.
To Groom Sideburns and Moustache:
1 Pull the shaving unit straight off the shaver.
C NOTE:
Do not turn the shaving unit while you
pull it off the shaver.
C
2
Insert the raised notch of the trimmer into
the slot in the top of the shaver. Press the
trimmer down to attach it to the shaver.You
will hear a ‘click’.
22
ENGLISH
ENGLISH
3 Turn shaver ON.
The display lights up for a few seconds.
C
4
Hold trimmer to exact hairline desired.
Move trimmer downward with gentle
pressure.
5
Trim beard, moustache or sideburns using
the trimmer.
C 10
Thoroughly clean the trimmer after using
(see ‘Cleaning’).
8 Pull the trimmer straight off the shaver.
C NOTE:
Do not turn or twist the trimming unit
while you pull it off the shaver.
If you are going to store the shaver for a longer
time period or if traveling, it is possible to lock the
shaver. The travel lock prevents the shaver from
being switched on by accident.
Activating the travel lock
C
3 sec.
1
9
Insert the raised notch of the shaving unit
into the slot in the top of the shaver. Press
the shaving unit down to attach it to the
shaver.You will hear a ‘click’.
Press the ON/OFF button for 3 seconds.
◗ The travel lock symbol lights up white
continuously.
◗ The shaver beeps and the lock symbol blinks.
2
C
Place the shaver in the SmartClean System
to protect heads.
Travel Lock
6 Turn shaver OFF when finished.
The display lights up for a few seconds and then
shows the remaining battery capacity charge
percentage.
7
23
The travel lock has now been activated.
Deactivating the travel lock
1
Press the ON/OFF button for 3 seconds.
24
ENGLISH
C
ENGLISH
2
The lock symbol blinks and then lights up
continuously. The shaver is now ready for
use.
BThe shaver unlocks automatically when charging
in the SmartClean System or when connected to
an electrical outlet.
25
◗ Regular cleaning guarantees better shaving
results.
◗ While rinsing shaving heads, water may drip
out of the base of shaver. This is a normal
occurrence.
C
1
For best results rinse the shaving unit by
running under hot water for a few minutes.
C
2
Pull the top portion of the shaving unit
straight off the shaver.
C
3
Rinse the hair chamber under the tap.
C
4
Rinse the shaving unit under hot tap water.
Cleaning
◗ Always clean your shaver after each use.
◗ Regular cleaning guarantees better shaving
results.
◗ Never clean, remove or replace shaving unit
while motor is on.
◗ Do not apply pressure to shaving head combs.
Do not touch shaver heads with hard objects
as this may dent or damage precision-made
slotted combs.
◗ Do not use shaver if shaving head combs are
damaged or broken. Facial injury may occur.
◗ Do not use abrasives, scourers or aggressive
liquids such as gasoline or acetone to clean
the shaver.
Cleaning the Shaving Unit
The shaving heads may be quickly cleaned after
each use by rinsing with hot water. Water from
the tap should be on a hot setting, BUT BE
CAREFUL TO TEST WATER FIRST SO AS NOT
TO BURN OR SCALD HANDS.
BE CAREFUL TO TEST WATER FIRST SO AS
NOT TO BURN OR SCALD HANDS.
5
Carefully shake off excess water and let
the shaving unit air dry completely.
26
ENGLISH
ENGLISH
◗ Place the SmartClean System on a flat,
stable and fluid-resistant surface to avoid any
leakage. Be careful not to tip or move the
SmartClean System when it is ready for use.
◗ Use this appliance for its intended household
use as described in this manual.
NOTE: Do not wipe or dry the shaving unit with
a towel or tissue. This could damage the shaving
heads.
6
Press the top portion of the shaving unit
down to attach it to the shaver head
holder.You will hear a ‘click’.
C
Preparing SmartClean System For
Use
CAUTION: Keep cleaning cartridge(s) out of
reach of children. Do not take internally. Avoid
contact with eyes. In case of eye contact,
thoroughly flush with cold water. If irritation
persists, get medical attention.
Important
◗ Only use this shaver, SmartClean System and
cleaning cartridge provided to charge or clean
shaver.
◗ Other Philips Norelco shavers may not work
with this SmartClean System.
◗ For optimal cleaning results, replace the
cleaning cartridge every 3 months.
◗ To avoid evaporation, do not expose cleaning
solution to direct sunlight.
◗ The SmartClean System thoroughly cleans but
does not disinfect your shaver, therefore, do
not share shaver with others.
◗ The charging plug converts 100-240V AC to
less than 24V DC.
27
Place the SmartClean System on a flat, level
surface.
To prevent leaking, do not tilt the SmartClean
System.
1
C
2
While holding the SmartClean System with
one hand, press the button located on the
side of the SmartClean System (1) and lift
the SmartClean System (2).
C
3
Remove the seal off the cleaning cartridge.
2
1
NOTE: ONLY USE PHILIPS NORELCO
SMARTCLEAN CARTRIDGE (MODEL JC302)
WITH THE SMARTCLEAN SYSTEM.
◗ When the cleaning cartridge filter is full, the
replacement symbol blinks indicating the
cleaning cartridge should be replaced. See
'Replacing the SmartClean System Cartridge'.
C
4
Place the cleaning cartridge in the
SmartClean System.
28
ENGLISH
C
ENGLISH
5
While holding the SmartClean System with
one hand, gently push the top part of the
SmartClean System back down.You will
hear a 'click'.
29
removed from the cleaning cartridge (see
‘Preparing SmartClean System For Use’).
C
4
Shake off any excess water from shaver
before placing in the SmartClean System.
C
5
Hold the shaver head side down above the
shaver holder.
When the SmartClean System is ready for use,
do not move appliance to prevent leakage.
Cleaning the Shaver in the
SmartClean System
C ◗ SmartClean System has two phases: a cleaning
phase and a drying phase.
◗ If the shaver does not contain enough power
for one (1) shave, the SmartClean System
may not work properly. Charge the shaver
in the SmartClean System before using the
SmartClean System to clean your shaver.
◗ If you use the shaver with shaving foam or gel,
quickly rinse under hot water before cleaning
in the SmartClean System.
C
1
Connect the small plug to the SmartClean
System. Connect the power plug into any
100V to 240V AC outlet. Use only the
power cord provided.
2
Press the top cap to open the SmartClean
System.
3.
Place the SmartClean System on a flat,
level surface. Make sure the seal has been
3
1
C
2
Place the shaver into the holder (1), push
shaver back (2) and press down the top
cap to connect the shaver (3) (click).
The shaver will only fit in the SmartClean System
in one direction.
6
7
C
The battery symbol slowly blinks to
indicate shaver is charging.
Press the ON/OFF button on the
SmartClean System to start the cleaning
cycle. (click).
The cleaning symbol will blink.
8
◗ The cleaning cycle takes approximately 10
minutes. When completed, the cleaning
symbol will light up continuously and the
drying phase starts automatically.
30
ENGLISH
ENGLISH
C ◗ During the drying phase, the drying symbol
blinks.
◗ The drying phase takes approximately 4 hours.
When completed, the drying symbol will light
up continuously.
◗ Do not press the ON/OFF button while the
cleaning cycle is running. If this does occur, the
cleaning cycle will stop and the cleaning or
drying symbol goes off . The cleaning cycle can
be re-started by pressing the ON/OFF button
once.
◗ If the power plug is disconnected before the
cleaning cycle is complete, reconnect the plug
into the outlet and the cleaning cycle can be
re-started by pressing the ON/OFF button
once.
C
C
1
3
2
NOTE: When the cleaning cartridge filter is full,
the replacement symbol blinks orange. (See
'Replacing the SmartClean System Cartridge').
When the entire cleaning cycle is complete
and the shaver is hygienically clean, the
ready symbol lights up continuously.
The battery symbol on the shaver will light up to
indicate the shaver is fully charged.
9
C 10
Press the top cap (1), pull the shaver
forward (2) and lift shaver from
SmartClean holder (3).
31
◗ The SmartClean System automatically turns
off 30 minutes after the cleaning and drying
phases are complete.
C 11
Place the shaver in the SmartClean System
to protect shaver heads.
Cleaning the Trimmer
Clean the trimmer after each use.
C
C
1
Attach the trimmer to shaver.
2
Turn shaver ON.
3
Rinse the trimmer under hot water. BUT
BE CAREFUL TO TEST WATER FIRST SO
AS NOT TO BURN OR SCALD HANDS.
4
Turn shaver off. Shake off excess water and
allow trimmer to air dry thoroughly.
Tip: For optimal trimmer performance, lubricate
the trimmer teeth with one drop of mineral
oil every 6 months.
32
ENGLISH
ENGLISH
Replacing the Shaving Unit
C
◗ Replace the shaving unit once a year for
optimal shaving results.
◗ Replace damaged or worn shaver heads with
model SH90 Philips Norelco shaver heads
only.
C
Replacement Shaver Head Assembly
Indication
C ◗ The shaving unit symbol lights up continuously,
the arrows blink and you will hear a beep
when the shaver is turned off to remind you
to replace your shaving unit to obtain optimal
shaving results.
3
1
C
1
Pull the top portion of the shaving unit
straight off the shaver.
C
2
Place the retaining ring holder on the
retaining ring (1), turn counterclockwise
(2) and lift it off the shaving head (3).
3
Remove the retaining ring from the
retaining ring holder and repeat the
process for the other retaining rings.
2
C
Remove the shaving heads from the
shaving head holder and discard.
DO NOT discard the retaining ring.
4
5 Place new shaving heads in the holder.
Make sure the notches on both sides of the
shaving heads fit exactly onto the projections in
the shaving head holder.
6
1
2
3
C
C
2
Place the retaining ring holder on the
retaining ring (1), place it on the shaving
head (2) and turn clockwise (3) to reattach
the retaining ring.
NOTE: Each retaining ring has two recesses that
fit exactly into the projections of the shaving
head holder. Turn the ring clockwise until you
hear a click to indicate the ring is fixed into
place.
7
1
33
Repeat this process for the other retaining
rings.
Hold the shaving head holder in your hand
and place the retaining ring on the shaving
head holder (1). Turn clockwise (2) to
reattach the retaining ring.
Do not place the shaving head holder on a
surface, as damage may occur.
8
ENGLISH
34
ENGLISH
Attach the shaving head holder to the
bottom part of the shaving unit (click).
9
7 sec.
C 10
To reset the shaver, press and hold the On/
Off button for approximately 7 seconds.
You will hear 2 beeps.
This shaver/SmartClean System has no other
user-serviceable parts. For assistance call 1-800243-3050.
3 Discard the empty cleaning cartridge.
Contact your local town or city officials for
recycling information.
C
4
Remove the seal off the new cleaning
cartridge.
C
5
Place the new cleaning cartridge in the
SmartClean System.
C
6
While holding the SmartClean System with
one hand, gently push the top part of the
SmartClean System back down.You will
hear a 'click'.
Replacing the SmartClean System
Cleaning Cartridge
C ◗ For optimal cleaning results, replace the
cleaning cartridge when the replacement
indicator blinks orange or every 3 months.
C
1
2
1
C
While holding the SmartClean System
with one hand, press the cartridge release
button on the side of the SmartClean
System (1) and lift the SmartClean System
(2).
Remove the empty cleaning cartridge and
pour any remaining cleaning fluid out of
the cleaning cartridge.
You can safely pour the cleaning fluid down the
sink.
2
35
When the SmartClean System is ready for use,
do not move appliance to prevent leakage.
36
ENGLISH
ENGLISH
Maintenance
Assistance
◗ Always remove shaver from the SmartClean
System before cleaning appliance.
◗ The SmartClean System and shaver may be
wiped clean using a damp cloth.
◗ Water from the tap should be on a warm
setting to clean any washable parts.
◗ For assistance, visit our website:
NOTE: DO NOT place or clean any parts of the
SmartClean System in a dishwasher.
Storage
shaver can be placed in the travel pouch
C ◗ The
or SmartClean System for safe storage.
◗ Be sure shaver is turned off. Remove cord
from outlet before storing in a safe, dry
location where it will not be crushed, banged,
or subject to damage.
◗ Do not wrap power cord around shaver or
SmartClean System when storing.
◗ Store cord in a safe location where it will not
be cut or damaged.
◗ Do not place or store SmartClean System
where it can fall or be pulled into a tub or
sink, water or other liquid while plugged in.
37
www.philips.com/support or
call 1-800-243-3050.
◗ Online information is available 24 hours a day,
7 days a week.
Disposal
Philips Norelco shaver contains a
C ◗ This
rechargeable Lithium-Ion battery
which must be disposed of properly.
◗ Contact your local town or city officials
for battery disposal information or call
1-800-822-8837 or www.rbrc.com for battery
drop-off locations.
◗ Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused. For
recycling information, please contact your
local waste management facilities or visit
www.recycle.philips.com.
◗ For assistance, visit our website,
www.philips.com/support or call toll free:
1-800-243-3050.
38
ENGLISH
39
Accessories
Replacement Shaving Unit
C ◗ Model
SH90 - For maximum shaver
performance, replace your Philips Norelco
shaver heads once a year.
◗ Replacement Cleaning Cartridge
Model JC302 - Philips Norelco SmartClean
Cleaning Cartridge, 2-Pack
Model JC303 - Philips Norelco SmartClean
Cleaning Cartridge, 3-Pack
◗ SmartClick Cleansing Brush
Model RQ585 - Philips Norelco SmartClick
Cleansing Brush
◗ Philips Norelco Shaver Accessories may be
purchased at a store near you, or on our
website www.philips.com/store
FULL TWO YEAR WARRANTY
Philips Electronics North America Corporation warrants each new Philips Norelco Product, Models S9531/
S9311 (except cutters and combs) against defects in materials or workmanship for a period of two years
from the date of purchase, and agrees to repair or replace any defective product without charge.
IMPORTANT: This warranty does not cover damage resulting from accident, misuse or abuse, lack of
reasonable care, the affixing of any attachment not provided with the product or loss
of parts or subjecting the product to any but the specified voltage.*
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply go to www.philips.com/norelco or call 1-800-243-3050 for assistance. It is suggested that for your protection you return shipments of product by insured mail, insurance
prepaid. Damage occurring during shipment is not covered by this warranty.
NOTE: No other warranty, written or oral, is authorized by Philips Electronics North America
Corporation.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to
state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the
above exclusion and limitations may not apply to you.
* Read enclosed instructions carefully.
Manufactured for:
Philips Consumer Lifestyle
A division of Philips Electronics North America Corporation
P.O.Box 10313, Stamford, CT 06904
This symbol on the product’s nameplate means it is
listed by Underwriters’ Laboratories, Inc.
Norelco and Tripleheader are registered trademarks of Philips Electronics North America Corporation.
PHILIPS is a registered trademark of Koninklijke Philips N.V.
© 2016 Philips Electronics North America Corporation. All Rights Reserved.
4222 002 5878 1